Olympia Innovations Y00L Smart Lantern User Manual

Olympia Innovations Inc. Smart Lantern O2Tech Quickstart ML 1204 R2ai

a href="https://usermanual.wiki/Olympia-Innovations" itemprop="url"> Olympia Innovations >

User Manual

SMART LANTERNHARDWARE SETUP1Remove the battery pack from the base of the lantern by squeezing the side clips and insert four (4) D cell batteries (batteries not included).Slide the battery pack back into the base of the lantern until you hear the side clips snap into place.2Press the power button once to turn on the lantern.Press the power button again to cycle through the High, Medium, Low, Flash, S.O.S. and Standby modes.Press and hold the power button continuously for 3 seconds to completely power off the lantern.DOWNLOAD THE APP3Get the O2Tech Smart Lantern app for Android or iPhone by scanning this QR code, or by visiting http://o2tech.co on your smartphone.TURN OVER PAGEPAGE 1 / 3SMART LANTERNFCC RULES OPERATIONNOTICE:This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions:¥ This device may not cause harmful interference, and ¥ This device must accept any interference received, including interference that may !!cause undesired operation.NOTICE:Changes or modiÞcations made to this equipment not expressly approved by (manufacturer name) may void the FCC authorization to operate this equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:¥ Reorient or relocate the receiving antenna.¥ Increase the separation between the equipment and receiver.¥ Connect the equipment into an outlet on a circuit different from that to which the ! !receiver is connected.¥ Consult the dealer or an experienced radio/TV technician for help.The radiated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.PAGE 3 / 3PAGE 4/4 PAGE 1/4
SMART LANTERNCONNECT THE LANTERN TO YOUR PHONE4Press the power button once to ensure the lantern is turned on. The logo on the power button will glow white when the lantern is on, or in standby mode.Standby mode allows the lantern to remain connected to your app while no light is on. 5On your iPhone or Android device, go to your device’s Settings screen and tap on Bluetooth. In the Bluetooth screen, make sure Bluetooth has been switched on.It’s best to place your lantern close to your iPhone or Android device when Þrst connecting.6Open the O2Tech Smart Lantern app and follow the instructions to connect to your lantern.You can control up to Þve lanterns at once from the same app. Any settings you change such as brightness or color will apply to all lanterns at once.PAGE 2 / 3SMART LANTERNBATTERY WARNINGFrequent attempts to connect to the O2Tech Smart Lantern while not in use by Bluetooth apps may drain the lantern's battery pack. Please remove the battery pack from your O2Tech Smart Lantern while not in use.PAGE 2/4PAGE 3/4
Download: Olympia Innovations Y00L Smart Lantern User Manual
Mirror Download [FCC.gov]Olympia Innovations Y00L Smart Lantern User Manual
Document ID3043238
Application IDdBhRx3qVuZ517B3ZAD3utA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize117.79kB (1472363 bits)
Date Submitted2016-06-28 00:00:00
Date Available2016-07-03 00:00:00
Creation Date2016-04-12 16:11:01
Producing SoftwareAdobe PDF library 10.01
Document Lastmod2016-04-12 16:11:02
Document TitleO2Tech Quickstart.ML 1204 R2ai
Document CreatorAdobe Illustrator CS6 (Windows)
FCC ID Filing: 2AHNTY00L

Navigation menu