Omni Intelligent Technology C1 Wireless remote control of intelligent tail lights User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3722035
Application ID	k1AF0IdnpUSGMd/kVABNIQ==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.44kB (330527 bits)
Date Submitted	2018-01-22 00:00:00
Date Available	2018-01-22 00:00:00
Creation Date	2018-01-18 19:45:59
Producing Software	LibreOffice 5.2
Document Lastmod	0000-00-00 00:00:00
Document Title	user manual
Document Creator	Draw

VI. Product specification:
IV. Installation:
◇Rear light size : 110mm*65mm*30mm ◇Wireless
Installation of the rear light:
1. Remove the rear light and bracket from packaging. Attach the bracket to the light
Wireless remote control of
intelligent tail lights
using the provided bolt and secure with the nut. See Photo A for reference.
2. As shown in Photo B, attach the bracket onto the bicycle's seat tube and secure with
lights, brake light, safety laser lane guidance lights, low battery warning light, and ambient sensor
detection. All this controlled by the rechargeable remote that attaches to the handlebars for easy
Photo B
①
⑥
①
⑥
②
Yellow left turning light
③
Yellow right turning light
④
⑤
②
③
⑤
④
Red alarming light
⑥
On/off button
USB charging interface
Left/right laser light
Button on rear light:
3. Rear light bracket 1pcs
1.When the light is OFF, press the power button to check the battery status and
4. Rubber belt 1pcs
2.Press and hold the power button to turn the unit ON and the LED red light
7. Manual Instruction 1pcs
60% Power Display
Photo C
will stay ON.
2. Please charge this light if six months no use, otherwise may cause battery less charged
Ambient light sensor
3. This product waterproof level is IPX4. Could be used in small to moderate rain, please don’t suck
When the unit is in OFF mode (bike light turned ON but red LED turned OFF), the ambient light sensor
is active. If the sensors (located on the underbelly of the bike light) are exposed to light for more than
5 seconds, the unit's red LED lights will shut off. If the sensors are exposed to darkness for more than
user’s authority to operate the equipment. This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
Photo D
television reception, which can be determined by turning the equipment off and on, the user is encouraged
‐‐ Reorient or relocate the receiving antenna.
Photo E
‐‐ Consult the dealer or an experienced radio/TV technician for help.
5.Right Turning Button: Same as left turning button. See photo F.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2)This device must accept any interference received,
6.Braking Light: Press and hold the brake light when braking. The LED light will
be get brighter to signal users that you are braking.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
light will turn itself OFF and return to original mode after 1 minute. See photo E.
Brake light
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
to try to correct the interference by one or more of the following measures:
4.Left Turning Button: Press to activate the left turning signal. The yellow LED light
Laser light
the product in to water
. FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the
and OFF. See photo D.
will be flashing on the left side of the bike light. Press again to turn OFF. The
NOTE : Rear light screw , nut : M5*30mm Remote control screw , nut : M5*30mm
Light-bracket screw, nut : M4*26.5mm
damage is not included in warranty
ON, blinking, and OFF.
3.Laser Light Button: Press to select between 3 modes; constantly ON, blinking,
Left turning light
VII I. Warning :
1. Don’t disassemble the rear light by yourself . Inside the light there is dismantling fragile stickers,
2.Mode Switch Button: Press to switch between the 3 modes; constant ON,
Right turning light
manual guide
6. USB Charging Wire 1pcs
3.When light is ON, press the power button to switch between 3 modes; constant
blinking, and OFF (ambient sensor).
Remote control
bicycle turning rear laser light
5. Screw ,nut 3pcs
the red LED lights will come on to show current power. Each set of 3 LED lights
Remote control function(rear light should be on)
Mode Switch Button
VI I.Packing list:
2. Remote control 1pcs
1. On / Off Button: Press and hold the power button to turn ON and OFF.
On/off button
constantly ON when fully charged.
1. 433.92MHz Bicycle Rear Light 1pcs
2 seconds, the red LED lights will come ON.
III. Remote control button
Rear light off standby over 3 years
◇Remote control endurance: standby more than 4 months
V. Function:
LED lights with blink 3 times and then turn OFF.
Ⅱ .Product appearance :
◇
Waterproof level : IPX4
-20-- +60℃
◇Remote control charging time: 2.5 hours. Led light will be flashing white charging and stay
represents 20% power. When the power is too low to turn the unit ON, the red
functionality.
◇emote control battery capacity: 180mAh
◇Working environment:
◇Rear light full battery standby: rear light button on but light off standby time 14 days
and nut to secure onto the handlebar. The remote control is suitable for 18-20mm wide handlebars.
inspired by batman himself, the light is stylish and functional. The light offers left and right turn signal
◇Rear light battery capacity: 2200mAh
Full charge red light constant on
3.The degree of the rear light can be adjusted and secured into place by tightening
Remove the remote control from packaging and attach to the handlebar of the bicycle. Use the provided bolt
A rechargeable bicycle light that offers additional safety for cyclists while riding at night. A design
◇
Laser light transmission distance : 5m
◇Rear light charging time: charging take 3.5 hours. When charging 3 red light flashing.
the tube within the bracket. The bracket is for a suitable seat tube of 25-32mm.
Installation of the remote control
Ⅰ .Product information:
◇
Rear light charging input : DC5V 800Ma
◇Red alarming light brightness : 85 lumen
◇Rear light endurance: normal brightness 7 hours
the bolt and nut. If it is too loose, add the provided rubber belt by wrapping it around
the bolt and nut combo from step 1.
Manual guide
Photo A
◇Rear light weight : 125g
transfer mode : 433.92MHz
Photo F
including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 1
Creator                         : Draw
Producer                        : LibreOffice 5.2
Create Date                     : 2018:01:18 19:45:59+01:00

EXIF Metadata provided by EXIF.tools