Omron Master Control Units Users Manual

2015-01-24

• Front
• CompoBus/S SRM1(-V2) Master Control Units Operation Manual
• Notice:
• TABLE OF CONTENTS
• About this Manual:
• PRECAUTIONS
  • 1 Intended Audience
  • 2 General Precautions
  • 3 Safety Precautions
  • 4 Operating Environment Precautions
  • 5 Application Precautions
• SECTION 1 Introduction
  • 1-1 SRM1 Features and Functions
    • 1-1-1 Features
    • 1-1-2 Functions
  • 1-2 System Configuration
    • 1-2-1 Basic Configuration
    • 1-2-2 SRM1 Models
    • 1-2-3 Peripheral Connections
  • 1-3 Procedures From System Design to Test Operation
  • 1-4 I/O and Data Area Allocations
    • 1-4-1 I/O Allocations
    • 1-4-2 Data Area Allocation
• SECTION 2 Specifications and Components
  • 2-1 Specifications
    • 2-1-1 General Specifications
    • 2-1-2 Characteristics
    • 2-1-3 CompoBus/S Communications Specifications
  • 2-2 Unit Components
• SECTION 3 Installation and Wiring
  • 3-1 System Design
    • 3-1-1 Power Supply Wiring
    • 3-1-2 Interlock and Limit Circuits
    • 3-1-3 Power Supply Sequence
  • 3-2 Selecting an Installation Site
    • 3-2-1 Installation Site Conditions
    • 3-2-2 Panel/Cabinet Installation
  • 3-3 Installing the SRM1
    • 3-3-1 Surface Installation
    • 3-3-2 DIN Track Installation
  • 3-4 Wiring and Connections
    • 3-4-1 General Precautions for Wiring
    • 3-4-2 Power Supply Wiring
    • 3-4-3 CompoBus/S Transmission Line Wiring
    • 3-4-4 RS-232C Port Wiring
    • 3-4-5 Host Link Connections
  • 3-5 One-to-one NT Link
  • 3-6 One-to-N NT Link
  • 3-7 One-to-one PC Link Connections
    • 3-7-1 Basics
    • 3-7-2 Restrictions
    • 3-7-3 Cable Connections
    • 3-7-4 PC Setup Settings
• SECTION 4 Using the Programming Console
  • 4-1 Basic Operations
    • 4-1-1 Compatible Programming Consoles
    • 4-1-2 Connecting the Programming Console
    • 4-1-3 Changing the SRM1’s Mode
  • 4-2 Programming Console Operations
    • 4-2-1 Overview
    • 4-2-2 Clearing Memory
    • 4-2-3 Reading/Clearing Error Messages
    • 4-2-4 Buzzer Operation
    • 4-2-5 Reading UM Area Information
    • 4-2-6 Setting Expansion Instructions
    • 4-2-7 Setting and Reading a Program Memory Address and Monitoring I/O Bit Status
    • 4-2-8 Instruction Search
    • 4-2-9 Bit Operand Search
    • 4-2-10 Inserting and Deleting Instructions
    • -4- 2-11 Entering or Editing Programs
    • 4-2-12 Checking the Program
    • 4-2-13 Bit, Digit, Word Monitor
    • 4-2-14 Differentiation Monitor
    • 4-2-15 Binary Monitor
    • 4-2-16 Three-Word Monitor
    • 4-2-17 Signed Decimal Monitor
    • 4-2-18 Unsigned Decimal Monitor
    • 4-2-19 Three-Word Data Modification
    • 4-2-20 Changing Timer, Counter SV
    • 4-2-21 Hexadecimal, BCD Data Modification
    • 4-2-22 Binary Data Modification
    • 4-2-23 Signed Decimal Data Modification
    • 4-2-24 Unsigned Decimal Data Modification
    • 4-2-25 Force Set, Reset
    • 4-2-26 Clear Force Set/Reset
    • 4-2-27 Hex-ASCII Display Change
    • 4-2-28 Displaying the Cycle Time
• SECTION 5 Test Runs and Error Processing
  • 5-1 Startup Procedure
    • 5-1-1 Flowchart for Configuring and Checking the System
    • 5-1-2 SRM1 Test Run Procedure
    • 5-1-3 Flash Memory Precautions
  • 5-2 Entering the Program
    • 5-2-1 Before Programming
    • 5-2-2 Clearing Memory
    • 5-2-3 Ladder Programming Example
    • 5-2-4 Writing the Program
    • 5-2-5 Checking the Program
  • 5-3 Test Run
  • 5-4 Error Processing
    • 5-4-1 Non-fatal Errors
    • 5-4-2 Fatal Errors
    • 5-4-3 Identifying Errors
    • 5-4-4 User-defined Errors
    • 5-4-5 Reading/Clearing Error Messages
  • 5-5 Programming Console Operation Errors
  • 5-6 Programming Errors
  • 5-7 Troubleshooting Flowcharts
• SECTION 6 Expansion Memory Unit
  • 6-1 Overview
    • 6-1-1 Memory Areas
    • 6-1-2 Precautions
  • 6-2 Specifications and Nomenclature
    • 6-2-1 Specifications
    • 6-2-2 Nomenclature
  • 6-3 Handling
    • 6-3-1 Mounting/Removing EEPROM
    • 6-3-2 PC Connections
    • 6-3-3 Uploading Programs
    • 6-3-4 Downloading Programs
• Appendix
  • Appendix A Standard Models
  • Appendix B External Dimensions
• Glossary
• Index
• Revision History