Ondas Networks FS-NPCS000 PtMP Broadband Wireless System User Manual FCC Part 15

Full Spectrum Inc. PtMP Broadband Wireless System FCC Part 15

User Manual

Rhein Tech Laboratories, Inc. Client: Full Spectrum Inc. 360 Herndon Parkway Models: BS100 & MS400 Suite 1400 FCC ID: X27-FS-NPCS000 Herndon, VA 20170 Standard: FCC Part 24 http://www.rheintech.com Report #: 2009306 42 of 46 Appendix J : Manual Please refer to the following pages.
Fullax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential FullMax BS100 and MS400 User Manual Version 1.1 March 9, 2010
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 2Table of Contents 1 Overview ........................................................................................................ 3 2 FullMax Description ....................................................................................... 4 2.1 System Description .............................................................................. 4 2.2 BS100 and MS400 Hardware Architecture ......................................... 5 2.3 FullMax BS100 and BS400 Software Architecture ........................... 11 3 FullMax BS100 and MS400 Embedded Software Functionality ................... 12 4 FullMax System Installation and Commissioning ......................................... 14 4.1 Enclosure of BS100 and MS400 ........................................................ 14 4.2 Connecting the BS100 and MS400 .................................................... 14 4.3 FullMax BS100 & MS400 Tune Up and Alignment Procedures ....... 15 4.4 CLI Commands for BS100 ................................................................. 16 4.5 Monitoring the BS / MS with FullMax NMS ....................................... 17 5 FullMax system operation ............................................................................ 18 5.1 Operation Restrictions ....................................................................... 18 5.2 BS100 Operation ................................................................................. 19 5.2.1 Main Group ................................................................................................... 19 5.2.2 mac-config .................................................................................................... 21 5.2.3 ul-config ........................................................................................................ 28 5.2.4 dl-config ........................................................................................................ 40 5.2.5 zone-config ................................................................................................... 45 5.2.6 bs-cap-config................................................................................................. 51 5.2.7 bs-burst-profile .............................................................................................. 53 5.2.8 bs-ss-action ................................................................................................... 56 5.2.9 ss-registered .................................................................................................. 57 5.2.10 ss-ip ........................................................................................................... 59 5.2.11 device ........................................................................................................ 61 5.2.12 Measurements ........................................................................................... 64 5.2.13 pkm–config ............................................................................................... 67 5.2.14 bs-private................................................................................................... 70 5.2.15 trap-config ................................................................................................. 76 5.2.16 lapc-config ................................................................................................ 78 5.3 MS400 Operation ................................................................................ 92 5.3.1 Main Group ................................................................................................... 92 5.3.2 ss-config ........................................................................................................ 93 5.3.3 device ............................................................................................................ 99 5.3.4 Measurements ............................................................................................. 102 5.3.5 ss-private ..................................................................................................... 105 5.3.6 ss-chconfig .................................................................................................. 111 5.3.7 ss-trap .......................................................................................................... 114 6 Annex A: Frequency Reuse Schemes ........... Error! Bookmark not defined.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 31 Overview a) FullMax is a Point to Multipoint (PtMP) broadband wireless system based on the WiMAX-e (IEEE 802.16e-2005) protocol with modifications needed to enable its operation in the Narrow PCS band (NPCS). The system consists of BS100 Base Stations, MS400 Mobile or Fixed subscriber stations, standard backhaul networking equipment connecting the BS100 Base Stations to a Router at the Network Operating Center (NOC) and a Network Management System (NMS). b) FullMax main modifications relative to the IEEE802.16e-2005 air interface protocol are: 1) The RF front end can tune to the enter frequencies within the following NPCS channels: a. 940.3000 – 940.8000 (500 kHz) b. 901.3000 – 901.7500 (450 kHz) c. 901.3000 – 901.7000 (400 kHz) d. 901.3500 – 901.7500 (400 kHz) e. 930.0000 – 930.4000 (400 kHz) f. 930.6000 – 931.0000 (400 kHz) g. 940.3000 – 940.7500 (450 kHz) h. 940.3000 – 940.7000 (400 kHz) i. 940.3500 – 940.7500 (400 kHz) 2) The BS100& MS400 operate in 400 KHz, 450 KHz and 500 KHz wide channels which are available in the NPCS band. 3) The BS100 and MS400 have analog and digital filters which are designed to meet the FCC Part 24 spectral mask in the transmit direction and the channel selectivity in the receive direction. c) Outline of the document: 1) Paragraph 2: FullMax system description 2) Paragraph 3: FullMax system operation 3) Paragraph 4: BS100 and MS400 installation and commissioning.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 42 FullMax Description 2.1 System Description a) FullMax system architecture is described in figure 2-1 below. The system is used to establish private, multi-cell, Point to Multipoint broadband wireless service for electrical utilities and other mission critical industries. It supports both fixed and mobile applications. FullMax BS’s are typically installed in the existing Private Land Mobile Radio (PLMR) towers serving their respective cells. Wireless backhaul facilities are used to connect the BS’s to the central site of the system. FullMax fixed and mobile SS’s are deployed throughout the tower’s serving area. BSBSBSBSBSBS Fig. 2-1: FullMax system architecture b) FullMax operates in unpaired spectrum using Time Division Duplex (TDD). FullMax also operates in paired spectrum employing each portion of the paired spectrum as an independent unpaired spectrum. c) FullMax BS100 is designed to support a single sector and as such, it supports the construction of a Base Station with multiple sectors (1, 2, 3 or more). An external bridge/router is used to forward/route the traffic to the appropriate sector. Note
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 5that the most common deployment is a 3 sector configuration. The sector configuration dictates the type of antenna that should be used. d) FullMax supports various frequency reuse schemes as outlined in Annex A to this document. e) The FullMax BS antenna is typically installed at an existing utility tower. The antenna should be installed as high on the tower as possible. The BS also employs a GPS antenna for TDD framing synchronization. f) FullMax MS400 can be used as either a fixed indoor Subscriber Station with an outdoor antenna or as a Mobile Station in a Utility truck. As a fixed SS, MS400 supports both Ethernet 100 Base T connectivity as well as serial RS232 connectivity. The serial connectivity is needed to support various legacy applications like Supervisory Control And Data Acquisition (SCADA) applications. 2.2 BS100 and MS400 Hardware Architecture a) The FullMax BS100 & MS400 radio architecture is described in figure 2-1 and 2-2 below. It consists of a Baseband Processor Board (BBP), an Analog Front End (AFE) section and a Low Voltage Power Supply (LVPS) board. b) The BBP block diagram is described in figure 2-3. It is the heart of the FullMax radio. It is designed to perform MAC, PHY, networking, network management and other functions that are required in a broadband wireless BS and MS. The BBP has the following main characteristics: 1) Processing resources: a. A TI DSP and a Xilinx Spartan 3A FPGA to execute the PHY layer b. A Freescale PQ3 processor to execute the MAC layer and complementary embedded software 2) A GPS time reference module is available for synchronization1 and for location based services. 3) User interfaces: 100 Base T, RS232 4) Interface to the AFE is done through a digital I/Q interface. c) The AFE section block diagram is described in figure 2-4. The AFE section performs signal processing functions that are needed to deliver the signal to the antenna and to receive the signal from the antenna. The AFE consists of: 1) A RF Small Signal (RFSS) board which contains a baseband section, an IF section and an RF section. 1 e.g. for TDD frame synchronization.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 6a. The baseband section consists of an A/D, D/A, a programmable receive baseband filter, a Digital Pre Distortion (DPD) Equalizer a programmable sampling clock synthesizer and a FPGA. b. The IF section consists of an IF LO, an I/Q modulator/demodulator, an IF receive channel bank and an IF transmit filter. c. The RF section consists of a RF LO, an RF up/down convertor, an RF receive channel bank and a RF transmit filter. 2) A RF Front End (RFFE) board which contains a RF PA, LNA, AGC and T/R switch. 3) The AFE employs three 8051 microcontrollers for monitoring and control of all aspects of the AFE operation. A serial interface protocol is available to support control of the master housekeeping microcontroller on the RFSS board by the main PQ3 processor on the BBP board. Note: The AFE employs a non agile external RF bandpass filter which is shown as a yellow block in the AFE block diagram in figure 4. d) The Low Voltage Power Supply (LVPS) block diagram is described in figure 2-5. The LVPS generates all the voltages that are needed at the BBP and the AFE. It is designed for an input voltage range of 9 to 36 VDC to support power feed for a vehicle battery. An optional external power brick is available if needed to support AC or -48 VDC power feed. Figure 2-1: FullMax BS100 & MS400 High Level Architecture
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 7 Figure 2-2: FullMax BS100 & MS400 Block Diagram SDR BS/MSAnalog Front End (AFE) BBP BoardRFSSRFFEPower Conn.On-off switch (For BS) I-3I-2UI110/100 Ethernet On-Off(For BS)DC power I-1I-4RS232COM portSDR Wireless connectivity GPS Wireless connectivityI-5I-7I-6Power -on Indicator I-8BITIndicator RJ45DB-9Low Voltage Power Supply (LVPS)(For MS)Power LED BIT LEDPower ConnectorEthernetconnectorSerial ConnectorProcessorJTAGDSPJTAGFPGAJTAGGPS SMAAFE ConnectorTest ConnectorGPS AntennaSDRAntenna
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 8MPC8548EFlash164MBBUFFERLATCHGPSTRANSLATORTMS320TCI6482I2CFPGAXC3SD3400AEMIFASerial ConfigurationAFECONNECTORIntegratedMagneticVerticalRJ45ConnectorPROMRJ45CONNECTORRS232DriverCPLDUART 1 & 233.33MHzMPC TEMPSENSORI2C EEPROMI2C25MHz125MHzPOWERSUPPLY3.3V5VMULTIPLIERMPCJTAGTMSJTAGXILINIXJTAG1.1V 2.5V 1.8V 1.24V 1.2V3.3V5V1.1VSENSOR2.5VSENSOR1.8VSENSOR1.24VSENSOR1.2VSENSORENABLE 1.1VENABLE 2.5VENABLE 1.8VENABLE 1.24VENABLE 1.2VENABLE 1.1VENABLE2.5VENABLE1.8VENABLE1.24VENABLE1.2VMPC I/O SUPPLYTMS I/O SUPPLYFPGA I/O SUPPLYMPC MPC MPC&TMS(DDR2)TMS FPGALED LED LED16XBUFFERGPIO-1,2I/O - 162.54mm10X2MCXConncectorMUX32MB 32MBPower -LED25MHzMARVELSWITCHRGMIIRGMIIAFE32V15V5V3.3V32V15V 5V3.3VDDR2 DDR2PORT0PORT2PORT1DDR2128MBDDR2128MBDDR2128MBDDR2128MBFlash164MB133MHzTRANSLATORSGMII Figure 2-3: Baseband Processor (BBP) Board Block Diagram
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 9 Figure 2- 4: Analog Front End (AFE) Block Diagram
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 10INPUTC0NNECTORRFFEU832V@10mALM317LFly back(U8)U915V@75mALM78L15ACFly backU155V@2ATPS75801LDOU173.3V@1.5AEN5336QBuckU163.3V@3AEN5364QBuckRFSS/BBPU528V/5ALM5118Buck-BoostFILTERU1Under/ OverVoltagemonitorLT4356 )O/Pconnectors9-36V DCReversePolarityprotectionProtection circuitsLow Voltage Power supply block diagramControlOver currentprotectionFUSEI_INI_IN_1I_IN_2I_OUT_128V/5A To RFFETo RFSSTo RFSSTo RFSSTo BBPTo BBPTo RFSSU35.15V/10ATPS40054BuckU45V@3ATPS75801LDOI_OUT_2U6SMPSController(UC3843) Figure 2-5: Low Voltage Power Supply (LVPS) Block Diagram
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 112.3 FullMax BS100 and BS400 Software Architecture a) FullMax BS100 and MS400 software architecture is described in figure 2-6 below. It consists of PHY layer, MAC layer and general purpose embedded software components. Figure 2-6: FullMax BS100 & MS400 software architecture
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 123 FullMax BS100 and MS400 Embedded Software Functionality a) FullMax BS100 and MS400 support the MAC and PHY layer requirements as defined in the “WiMAX Forum Mobile System Profile Release 1.0 Approved Specifications”. This section describes the complementary embedded software that is not considered part of the MAC and the PHY layer software. b) Networking: o Supports communication over a 100 Base T Ethernet interface o Supports IP host functionality: BS100 & MS400 have an IP address and they support the following IP protocols: DHCP, ARP, ICMP, TFTP, FTP, SNMP, ToD (RFC-868). Also, BS100 and MS400 have a read only MAC address which is programmable during manufacturing. o Learning bridge and layer 2 forwarding: BS100 and MS400 support learning bridge functionality, maintain a Table of Connected Entities (TCE) and use it to forward packets to the correct destination (Ethernet interface, wireless interface or IP host) c) QOS: o Most of the QOS functionality is considered part of the MAC layer. The general purpose embedded software provides complimentary QOS functionality such as traffic prioritization. d) Security: o The general embedded software supports encryption and authentication functionality and processes which are complimentary to the MAC layer security functionality. e) Provisioning: o IP address provisioning (the BS100 and MS400 acquire an IP address from an external standard DHCP server). o Time provisioning (the BS100 and MS400 acquire date and time from an RFC-868 Time server). o EAP Provisioning (The BS100 and MS400 acquire the MSK Key from the AAA server). o Configuration provisioning (The BS100 and MS400 configuration provisioning is done through CLI and through SNMP commands). o QoS Provisioning (The BS100 and MS400 QOS provisioning is done through SNMP commands).
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 13f) Channel Acquisition o The MS400 supports a pre-configured channel acquisition plan, i.e., a preconfigured list of channel alternatives, characterized by their center frequency and the bandwidth. The MS400 goes through the list and performs successive channel acquisition attempts until an attempt is successful. o Criteria for channel acquisition success: ■ Successful registration if the MS400 was not registered prior to channel acquisition. ■ Successful ranging if the MS400 was registered prior to channel acquisition (i.e., in the case of moving to a new BS100). o Once a channel is successfully acquired, the parameters of the acquired channel are saved to the MS400 flash memory and are used as first acquisition option on MS400 power on. g) Network Management Support o The BS100 and MS400 have a SNMPv2c agent and they can be remotely managed by FullMax Network Management System outlined in Paragraph 4 below. o The BS100 and MS400 also support a Telnet based Command Line Interface (CLI) protocol which can be used to configure all BS100 and MS400 parameters. h) Miscellaneous BS100 and MS400 hardware platform Management o Remote and secure software download o Initialization and configuration Persistence: The BS100 and MS400 support a CLI command that initiates the saving of the configuration in the flash. Saved configuration is used after power off.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 144 FullMax System Installation and Commissioning 4.1 Enclosure of BS100 and MS400 The BS100 and MS400 devices share the same enclosures Figure 1: Top View Figure 2: Bottom View (with FCC label) Figure 3: Front View Figure 4: Rear View Figure 5: Right Side View Figure 6: Left Side View 4.2 Connecting the BS100 and MS400 1. Place the enclosure in a stable location. Make sure that air can run freely to the fans on the rear of the enclosure and the holes on the enclosures sides. 2. Connect the cable from the Antenna to the device RF connector on the enclosure left side.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 153. Use an Ethernet cable to connect the device with end equipment 4. Connect the power cable to the power connector on the enclosure left side. 5. Connect the power label to the power source. 4.3 FullMax BS100 & MS400 Tune Up and Alignment Procedures 1. Frequency and transmit power configuration of the FullMax BS100 and MS400 is done by means of either a Command Line Interface (CLI) tool or a Web based Network Management (NMS) tool. 2. The NMS/CLI tools is used to configure the following parameters: a. BS100 parameters: i. Center RF frequency ii. Channel bandwidth iii. Transmit power b. MS400 parameters: i. Maximum uplink transmit power ii. An automatic channel acquisition table with up to 10 entries. Each entry includes the center frequency and the channel bandwidth. 3. The center frequency, channel bandwidth and transmit power at the BS100 are configured statically by the NMS/CLI tool. This means that the values will be maintained unless they are changed by the CLI/NMS tool. 4. The MS400 on the other hand, performs automatic channel acquisition by selecting dynamically, the best channel (highest RSSI) from a list of up to 10 pre-configured entries (see paragraph 2bi above). The transmit power of the MS is controlled by an automatic closed loop power control algorithm running at the BS100. The transmit power of the MS will be increased by the BS100 as the distance to the MS is increased (i.e., as the path loss increases and the RSSI as measured by the BS100 becomes lower). Note however that the MS will not transmit above the maximum uplink transmit power (see paragraph 2bii) even if ordered by the BS100. 5. Both BS and MS employ an external RF bandpass filter as described in Annex A to this document. This is an additional safeguard which guarantees that the BS100 and the MS400 will not transmit outside the band.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 16 6. The remainder of the document describes the CLI commands that are used to configure the BS100 and MS400 parameters described above. 4.4 CLI Commands for BS100 After logging in through telnet [FULLMAX]$ Prompt for user is displayed. Type help or ? to look at different groups. Lock to dl-config group using dl-config command [FULLMAX]$ [FULLMAX]$ dl-config You are locked to dl-config group. Only dl-config operations are allowed. Use help or ? for help. [FULLMAX(dl-config)]$ For Frequency: [FULLMAX(dl-config)]$ show center-freq center-freq 940500 khz [FULLMAX(dl-config)]$ set center-freq updated center-freq 930800 khz For Tx Power : [FULLMAX(dl-config)]$ show tx_power tx_power 9 dbm [FULLMAX(dl-config)]$ set tx_power 16 updated tx_power 16 dbm For Channel Bandwidth: [FULLMAX(dl-config)]$ show bandwidth bandwidth 500 khz For FFT-Size:
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 17 [FULLMAX(dl-config)]$ show fft_size fft_size 128fft 4.5 Monitoring the BS / MS with FullMax NMS For monitoring the BS availability and performance it should be added to the NMS. Login to NMS as an 'Admin'. If the BS100 is located in a new tower: On NMS menu select: Admin New BS Tower Type in tower name Click 'Save' On NMS menu select: Admin New BS Sector Type in a 'sector name' Select the tower on which the sector is installed Add the BS100 IP address Click 'Save' The BS100 availability and performance will now be monitored by the NMS
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 185 FullMax system operation 5.1 Operation Restrictions a) Changes or modifications not expressly approved by Full Spectrum Inc. could void the user’s authority to operate the equipment. b) While operated as a Mobile (non fixed application), the MS400 equipment shall only be installed and operated with the antenna type, and antenna gain not more than that approved for this certification (as per the table below). The antenna will be installed with minimum separation distance between the antenna and the general public and between the antenna and the trained personnel during normal operation as stated in the table below for the respective antenna gains. c) An example of an antenna authorized for use with the MS400 while used in a mobile application is Laird # B8965C Mobile Load Coil Antenna with unity gain in the horizontal direction and with 5 dBi vertical gain. Environment Numeric Gain Average Power (W) Separation Distance (cm) Power Density (mW/cm2) General population/Uncontrolled 3.16 3.1 36 0.6 Occupational/Controlled 3.16 3.1 20 3 General population/Uncontrolled 20 3.1 91 0.6 Occupational/Controlled 20 3.1 41 3 d) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 19to cause harmful interference in which case the user will be required to correct the interference at his own expense. 5.2 BS100 Operation FullMax BS CLI supports the following commands. The access to this commands are based on the user privileges. The Admin has the privilege to control and monitor all the information supported by the FullMax BS CLI commands, where as the operator has limited privileges. After the successful authentication, the user Is permitted access to the command line interface. Based on the user privileges, the help menu will be displayed to the user. 5.2.1 Main Group When user logs in to the CLI it will lock to the default group which is the main group.When ever the user enters the Main group,CLI will display the main prompt .Help command in main group will show the commands supported in main group along with the group lock commands. Only commands related to main group can be executed in main group. FullMax# ipipipip----addressaddressaddressaddress System IP address. Command Purpose Privileges FullMax# set ip-address <ip-address> Updates the system IP address. A/O FullMax# show ip-address Displays the system IP address. A/O Example: FullMax#set ip-address 10.60.4.42 Updated IP address: 10.60.4.42 FullMax# show ip-address IP address: 10.60.4.56 dhcpdhcpdhcpdhcp----configconfigconfigconfig----serverserverserverserver----ipipipip DHCP server IP address. Command Purpose Privileges FullMax#set dhcp-config-server-ip <ip-address> Allows the user to update the BS with the DHCP server IP address. A/O FullMax# show dhcp-config-server-ip Allows the user to display the remote DHCP server IP address A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 20 Example: FullMax# set dhcp-config-server-ip 10.60.1.11 Updated DHCP server IP 10.60.1.11 FullMax# show dhcp-config-server-ip DHCP server IP 0.0.0.0 dhcpdhcpdhcpdhcp----configconfigconfigconfig----remoteremoteremoteremote----idididid DHCP remote ID. Command Purpose Privileges FullMax# set dhcp-config-remote-id <mac-address> Allows the user to update the DHCP remote ID A/O FullMax# show dhcp-config-remote-id Allows the user to displays the DHCP remote ID A/O Example: FullMax# set dhcp-config-remote-id 0019D1:50CC62 Updated dhcp-config-remote-id 0019D1:50CC62 FullMax# show dhcp-config-remote-id dhcp-config-remote-id 0019D1:50CC62 dhcpdhcpdhcpdhcp----configconfigconfigconfig----circuitcircuitcircuitcircuit----idididid DHCP circuit ID Command Purpose Privileges FullMax# set dhcp-config-circuit-id Allows the user to updates the DHCP circuit ID A/O FullMax# show dhcp-config-circuit-id Allows the user to display the DHCP circuit ID A/O Example: FullMax# set dhcp-config-circuit-id 3 Updated dhcp-config-circuit-id 3 FullMax# show dhcp-config-circuit-id dhcp-config-circuit-id 0
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 21 5.2.2 mac-config mac-config group defines the commands that monitors or updates the MAC configuration information. The user upon entering the mac-config command , locks into this particular group to execute commands only related to BS configuration. FullMax# FullMax# mac-config FullMax(mac-config)# Command Purpose Privileges FullMax# mac-config The command allows the user to lock into the group mac-config and execute all the commands related to the group. A/O The commands supported by the mac-config group are dcd-interval The command describes the time between transmissions of DCD messages in milliseconds. Command Purpose Privileges FullMax(mac-config)# set dcd-interval <val> The command allows the user to update the transmission time between to DCD messages. A FullMax(mac-config)#show dcd-interval The command allows the user to find the time interval for transmission of consecutive DCD messages. A/O Example: FullMax(mac-config)# set dcd-interval 30 Updated dcd-interval 30 milliseconds FullMax(mac-config)# show dcd-interval dcd-interval 30 milliseconds ucducducducd----intervalintervalintervalinterval The command describes the time between transmissions of UCD messages in milliseconds. Command Purpose Privileges FullMax(mac-config)# set ucd-interval <val> The command allows the user to update the transmission time between to UCD messages. A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 22FullMax(mac-config)# show ucd-interval The command allows the user to find the time interval for transmission of consecutive UCD messages. A/O Example: FullMax(mac-config)# set ucd-interval 30 Updated ucd-interval 30 milliseconds FullMax(mac-config)# show ucd-interval ucd-interval 30 milliseconds dcddcddcddcd----transitiontransitiontransitiontransition The number of frames from the end of the frame carrying the DCD message the BS shall wait after transmitting a DCD message with an incremented Configuration Change count before issuing a DL-MAP message referring to Downlink Burst profiles defined in that DCD message. Command Purpose Privileges FullMax(mac-config)# set dcd-transition <val> This command allows the user to change the configuration count, the BS shall wait to transmit DL-MAP after transmitting the DCD message. A FullMax(mac-config)#show dcd-transition The command allows the user to find the configuration count, the BS shall wait (no. of frames) to transmit DL-MAP after transmitting the DCD message. A/O Example: FullMax(mac-config)# set dcd-transition 30 Updated dcd-transition 30 (MAC Frames) FullMax(mac-config)# show dcd-transition dcd-transition 30 (MAC Frames) ucducducducd----transitiontransitiontransitiontransition The number of frames from the end of the frame carrying the UCD message the BS shall wait after transmitting a UCD message with an incremented Configuration Change count before issuing a UL-MAP message referring to Uplink Burst profiles defined in that UCD message. Command Purpose Privileges FullMax(mac-config)# set ucd-transition <val> This command allows the user to change the configuration count, the BS shall wait to transmit UL-MAP after transmitting the UCD message. A FullMax(mac-config)#show The command allows the user to find the A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 23ucd-transition configuration count, the BS shall wait (no. of frames) to transmit UL-MAP after transmitting the UCD message. Example: FullMax(mac-config)# set ucd-transition 30 Updated ucd-transition 30 (MAC Frames) FullMax(mac-config)# show ucd-transition ucd-transition 30 (MAC Frames) DsxDsxDsxDsx----rsprsprsprsp----retriesretriesretriesretries Number of Timeout Retries on DSA/DSC/DSD Responses. Command Purpose Privileges FullMax(mac-config)# set dsx-rsp-retries <val> The command updates the value of the DSA/DSC/DSD responses retries timeout. A FullMax(mac-config)# show dsx-rsp-retries The command displays the DSA/DSC/DSD responses retries timeout. A/O Example: FullMax(mac-config)#set dsx-rsp-retries 6 Updated dsx-rsp-retries 6. FullMax(mac-config)#show dsx-rsp-retries dsx-rsp-retries 3 DsxDsxDsxDsx----reqreqreqreq----retriesretriesretriesretries Number of Timeout Retries on DSA/DSC/DSD Requests. Command Purpose Privileges FullMax(mac-config)# set dsx-req-retries <val> The command updates the value of the DSA/DSC/DSD requests retries timeout. A FullMax(mac-config)#show dsx-req-retries The command displays the DSA/DSC/DSD requests retries timeout. A/O Example: FullMax(mac-config)#set dsx-req-retries 6000 Updated dsx-req-retries 6000 milliseconds. FullMax(mac-config)#show dsx-req-retries dsx-req-retries 3.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 24 TTTT7777----timeouttimeouttimeouttimeout Wait for DSA/DSC/DSD Response Timeout in ms. Command Purpose Privileges FullMax (mac-config) # set t7-timeout <val> The command updates the value of T7 timer, with in which the BS/SS should wait for a DSx response. A FullMax (mac-config) # show t7-timeout The command displays the T7 timer, configured to which the BS/SS should wait for a DSx response. A/O Example: FullMax(mac-config)#set t7-timeout 300 Updated t7-timeout 300 milliseconds. FullMax(mac-config)# show t7-timeout t7-timeout 300 milliseconds. T8T8T8T8----timeouttimeouttimeouttimeout Wait for DSA/DSC/DSD Acknowledge Timeout in ms. Command Purpose Privileges FullMax(mac-config)# set t8-timeout <val> The command updates the value of T8 timer, with in which the BS/SS should wait for a DSx acknowledge. A FullMax(mac-config)# show t8-timeout The command displays the T8 timer, configured to which the BS/SS should wait for a DSx acknowledge. A/O Example: FullMax(mac-config)# set t8-timeout 100 Updated t8-timeout 100 milliseconds. FullMax(mac-config)# show t8-timeout t8-timeout 100 milliseconds. TTTT9999----timeouttimeouttimeouttimeout The time allowed between the BS sending a RNG-RSP to an SS, and receiving an SBC-REQ from that same SS. Command Purpose Privileges FullMax(mac-config)# set t9-timeout <val> The command updates the T9 timer value that waits for an SBC-REQ from an MS to A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 25which it has sent a RNG-RSP. FullMax(mac-config)#show t9-timeout The command displays the T9 Timer value configured in BS to wait for SBC-REQ from an MS to which the BS has sent the RNG-RSP. A/O Example: FullMax(mac-config)#set t9-timeout 3200 Updated t9-timeout 3200 milliseconds FullMax(mac-config)#show t9-timeout t9-timeout 3200 milliseconds TTTT11110000----timeouttimeouttimeouttimeout The maximum time allowed to wait for a dynamic service transaction to end. Command Purpose Privileges FullMax(mac-config)#set t10-timeout <val> The command updates the T10 timer value that waits for a dynamic service transaction end. A FullMax(mac-config)#show t10-timeout The command displays the T10 timer value that waits for a dynamic service transaction end. A/O Example: FullMax(mac-config)# set t10-timeout 1000 Updated t10-timeout 1000milliseconds FullMax(mac-config)# show t10-timeout T10-timeout 1000milliseconds TTTT13131313----timeouttimeouttimeouttimeout Time allowed for an SS, following the receipt of a REG-RSP message to send a TFTP-CPLT message to the BS. Command Purpose Privileges FullMax(mac-config)#set t13-timeout <val> The command updates the T13 timer for which the BS waits to receive TFTP-CPLT message after sending the REG-RSP. A FullMax(mac-config)#show t13-timeout The command displays the T13 timer configured at BS to wait for TFTP-CPLT message after sending the REG-RSP A/O Example: FullMax(mac-config)# set t13-timeout 13000
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 26 Updated t13-timeout 13000 milliseconds FullMax(mac-config)# show t13-timeout t13-timeout 13000 milliseconds TTTT17171717----timeouttimeouttimeouttimeout Time allowed for SS to complete authorization and key exchange. Command Purpose Privileges FullMax(mac-config)#set t17-timeout <val> The command updates the value of T17 timer, with in which the SS should complete the authorization and key exchange. A FullMax(mac-config)#show t17-timeout The command displays the T17 timer, configured to which the SS should complete the authorization and key exchange. A/O Example: FullMax(mac-config)#set t17-timeout 6000 Updated t17-timeout 6000 milliseconds. FullMax(mac-config)#show t17-timeout t17-timeout 6000 milliseconds. TTTT22222222----timeouttimeouttimeouttimeout Time to wait for an ARQ-reset. Command Purpose Privileges FullMax(mac-config)# set t22-timeout <val> The command updates the T22 timer for which the BS waits for ARQ reset. A FullMax(mac-config)# show t22-timeout The command displays the T22 timer configured at BS to wait for ARQ reset. A/O Example: FullMax(mac-config)# set t22-timeout 200 Updated t22-timeout 200 milliseconds FullMax(mac-config)# show t22-timeout t22-timeout 200 milliseconds autoautoautoauto----sfidsfidsfidsfid----enabledenabledenabledenabled The command defines weather BS is allowed to autonomously allocate SFIDs. If the BS is enabled with this feature, the BS can autonomously allocate SFIDs in configured SFID range. An SF is autonomously when it is not provisioned and may be initiated either by either BS or SS.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 27Command Purpose Privileges FullMax(mac-config)# set auto-sfid-enabled {enable | disable } This command allows the user to configure BS by allowing the BS to autonomously allocate SFIDs. A FullMax(mac-config)# show auto-sfid-enabled {enable | disable } This command displays the user, weather the BS is enabled/disabled to allocate SFIDs. A/O Example: FullMax(mac-config)# set auto-sfid-enabled ENABLE Updated auto-sfid-enabled ENABLED FullMax(mac-config)# show auto-sfid-enabled auto-sfid-enabled ENABLED minminminmin----autoautoautoauto----sfidsfidsfidsfid----rangerangerangerange The command defines the minimum value of the SFID for the range allocated to support the creation of service flows autonomously. Command Purpose Privileges FullMax(mac-config)# set min-auto-sfid-range <val> This command allows the user to define the minimum value of SFID to define the range in which the BS can autonomously create Service flows. A FullMax(mac-config)#show min-auto-sfid-range The command displays the user, the minimum value of sfid from which the BS can create service flows autonomously. A/O Example: FullMax(mac-config)# set min-auto-sfid-range 6200 Updated min-auto-sfid-range 6200 FullMax(mac-config)# show min-auto-sfid-range Updated min-auto-sfid-range 6200 maxmaxmaxmax----autoautoautoauto----sfidsfidsfidsfid----rangerangerangerange The command defines the maximum value of the SFID for the range allocated to support the creation of service flows autonomously. Command Purpose Privileges FullMax(mac-config)# set max-auto-sfid-range <val> This command allows the user to define the maximum value of SFID range in which the BS can autonomously create Service flows. A FullMax(mac-config)# show The command displays the user, the A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 28max-auto-sfid-range maximum value of sfid upto which the BS can create service flows autonomously. Example: FullMax(mac-config)# set max-auto-sfid-range 6300 Updated max-auto-sfid-range 6300 FullMax(mac-config)# show max-auto-sfid-range max-auto-sfid-range 6300 allallallall This command displays all the parametrs values for the mac-config group in CLI. Command Purpose Privileges FullMax(mac-config)#show all The command displays the user, the value of all the mib parameters of tables in the group. A/O Example: FullMax(mac-config)# show all dcd-interval 5000 milliseconds ucd-interval 5000 milliseconds ucd-transition 0 (MAC Frames) dcd-transition 0 (MAC Frames) t9-timeout 8000 milliseconds t13-timeout 0 milliseconds t15-timer 0 milliseconds t17-timeout 0 milliseconds auto-sfid-enabled DISABLE min-auto-sfid-range 0 max-auto-sfid-range 0 dsx-req-retries 3 dsx-rsp-retries 3 T7-timer 1000 milliseconds t8-timer 300 milliseconds t10-timer 3000 milliseconds t22-timer 200 milliseconds 5.2.3 ul-config The group defines the commands that monitors or updates the UCD channel attributes that define the characteristics of uplink channels. The user upon entering the ul-config command locks into the CLI to execute commands only related to BS uplink channel characteristics.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 29FullMax# FullMax# ul-config FullMax(ul-config)# Command Purpose FullMax# ul-config The command allows the user to lock into the group ul-config and execute all the commands related to the group. ct-based-reserve-timeout The number of UL-MAPs to receive before contention-based reservation is attempted again for the same connection. Command Purpose Privileges FullMax(ul-config)# set ct-based-reserve-timeout <val> The command allows the user to update number of UL-MAPs to receive before contention-based reservation is attempted again for the same connection. A FullMax(ul-config)#show ct-based-reserve-timeout The command allows the user to display number of UL-MAPs to receive before contention-based reservation is attempted again for the same connection. A/O Example: FullMax(ul-config)# set ct-based-reserve-timeout 30 Updated ct-based-reserve-timeout 30 FullMax(ul-config)# show ct-based-reserve-timeout ct-based-reserve-timeout 30 uplink-center-frequency Uplink center frequency (in KHz). Command Purpose Privileges FullMax(ul-config)#set uplink-center-frequecy <val> The command allows the user to update the uplink center frequency. A FullMax(ul-config)#show uplink-center-frequecy The command allows the user to display the uplink center frequency. A/O Example: FullMax (ul-config) # set uplink-center-frequency 30 updated uplink-center-frequecy 30 KHz FullMax (ul-config) # show uplink-center-frequency uplink-center-frequecy 30 KHz
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 30 init-rng-codes Number of initial ranging CDMA codes. Command Purpose Privileges FullMax(ul-config)# set init-rng-codes <val> The command allows the user to update the Number of initial ranging CDMA codes. A FullMax(ul-config)#show init-rng-codes The command allows the user to display the number of initial ranging CDMA codes. A/O Example: FullMax(ul-config)# set init-rng-codes 10 Updated init-rng-codes 10 FullMax(ul-config)# show init-rng-codes init-rng-codes 10 periodic-rng-codes Number of periodic ranging CDMA codes. Command Purpose Privileges FullMax(ul-config)# set periodic-rng-codes <val> The command allows the user to update the Number of periodic ranging CDMA codes. A FullMax(ul-config)#show periodic-rng-codes The command allows the user to display the number of periodic ranging CDMA codes. A/O Example: FullMax(ul-config)# set periodic-rng-codes 20 Updated periodic-rng-codes 20 FullMax(ul-config)# show periodic-rng-codes periodic-rng-codes 20 bandwidth-request-codes Number of bandwidth request codes. Command Purpose Privileges FullMax(ul-config)#set bandwidth-request-codes <val> The command allows the user to update the number of bandwidth request codes. A FullMax(ul-config)#show The command allows the user to display A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 31bandwidth-request-codes the number of bandwidth request codes. Example: FullMax(ul-config)#set bandwidth-request-codes 20 Updated bandwidth-request-codes 20 FullMax(ul-config)#show bandwidth-request-codes bandwidth-request-codes 20 per-rng-backoff-start Initial backoff window size for periodic ranging contention expressed as a power of 2 Command Purpose Privileges FullMax(ul-config)#set per-rng-backoff-start <val> The command allows the user to update the initial backoff window size for periodic ranging contention. A FullMax(ul-config)#show per-rng-backoff-start The command allows the user to display the initial backoff window size for periodic ranging contention. A/O Example: FullMax (ul-config) # set per-rng-backoff-start 4 Updated per-rng-backoff-start 4 FullMax (ul-config) # show per-rng-backoff-start per-rng-backoff-start 4 per-rng-backoff-end Final backoff window size for periodic ranging contention, expressed as a power of 2 Command Purpose Privileges FullMax(ul-config)# set per-rng-backoff-end <val> The command allows the user to update the final backoff window size for periodic ranging contention. A FullMax(ul-config)# show per-rng-backoff-end The command allows the user to display the final backoff window size for periodic ranging contention. A/O Example: FullMax(ul-config)# set per-rng-backoff-end 8 Updated per-rng-backoff-end 8
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 32 FullMax(ul-config)# show per-rng-backoff-end per-rng-backoff-end 8 start-off-rng-codes Indicates the starting number, of the group of codes used for uplink Command Purpose Privileges FullMax(ul-config)#set start-off-rng-codes <val> The command allows the user to update the starting number of the codes used for uplink A FullMax(ul-config)#show start-off-rng-codes The command allows the user to display the starting number of the codes used for uplink. A/O Example: FullMax(ul-config)# set start-off-rng-codes 64 Updated start-off-rng-codes 64 FullMax(ul-config)# show start-off-rng-codes start-off-rng-codes 64 permutation-base Determines the UL_PermBase parameter for the sub carrier permutation to be used on this uplink channel. Command Purpose Privileges FullMax(ul-config)# set permutation-base <val> The command allows the user to updates the UL_PermBase parameter for the sub carrier permutation to be used on this uplink channel. A FullMax(ul-config)# show permuation-base The command allows the user to display the UL_PermBase parameter for the sub carrier permutation to be used on this uplink channel. A/O Example: FullMax(ul-config)# set permutation-base 127 Updated permutation-base 127 FullMax(ul-config)#show permutation-base permutation-base 8 ul-alloc-sub-channel-bitmap
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 33This is a bitmap describing the physical sub-channels allocated to the segment in the UL, when using the uplink PUSC permutation. The LSB of the first byte shall correspond to subchannel 0. Command Purpose Privileges FullMax(ul-config)# set ul-alloc-sub-channel-bitmap <val> The command allows the used to update the ofdma subchannel allocation. A FullMax(ul-config)#show ul-alloc-sub-channel-bitmap The command allows the user to display the ofdma subchannel allocation. A/O Example: FullMax(ul-config)#set ul-alloc-sub-channel-bitmap 00110001 Updated ul-alloc-sub-channel-bitmap ff FullMax(ul-config)# show ul-alloc-sub-channel-bitmap ul-alloc-sub-channel-bitmap 00110001 band-amc-alloc-threshold Threshold of the maximum of the standard deviations of the individual bands CINR measurements over time to trigger mode transition from normal sub channel to Band AMC. Command Purpose Privileges FullMax(ul-config)# set band-amc-alloc-threshold <val> The command allows the user to update the parameter for AMC band allocation Threshold. A FullMax(ul-config)#show band-amc-alloc-threshold The command allows the user to display the parameter for AMC band allocation threshold. A/O Example: FullMax(ul-config)# set band-amc-alloc-threshold 64 Updated band-amc-alloc-threshold 64 dB FullMax(ul-config)# show band-amc-alloc-threshold band-amc-alloc-threshold 64 dB bandbandbandband----amcamcamcamc----releasereleasereleaserelease----thresholdthresholdthresholdthreshold Threshold of the maximum of the standard deviations of the individual bands CINR measurements over time to trigger mode transition from Band AMC to normal subchannel.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 34 Command Purpose Privileges FullMax(ul-config)# set band-amc-release-threshold <val> The command allows the user to update the parameter that defines the maximum threshold for AMC band. A FullMax(ul-config)#show band-amc-release-threshold The command allows the user to display the parameter that defines the maximum threshold for AMC band. A/O Example: FullMax(ul-config)# set band-amc-release-threshold 56 Updated band-amc-release-threshold 56 dB FullMax(ul-config)# show band-amc-release-threshold band-amc-release-threshold 56 dB bandbandbandband----amcamcamcamc----allocallocallocalloc----timertimertimertimer Minimum required number of frames to measure the average and standard deviation for the event of Band AMC triggering. Command Purpose Privileges FullMax(ul-config)# set band-amc-alloc-timer <val> The command allows the user to update the parameter that defines the minimum required number of frames to measure the average and standard deviation for the event of Band AMC triggering. A FullMax(ul-config)#show band-amc-alloc-timer The command allows the user to display parameter that defines the minimum required number of frames to measure the average and standard deviation for the event of Band AMC triggering. A/O Example: FullMax(ul-config)# set band-amc-alloc-timer 22 Updated band-amc-alloc-timer 22 Frames FullMax(ul-config)# show band-amc-alloc-timer band-amc-alloc-timer 22 Frames bandbandbandband----amcamcamcamc----releasereleasereleaserelease----timertimertimertimer Minimum required number of frames to measure the average and standard deviation for the event of Band AMC triggering.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 35 Command Purpose Privileges FullMax(ul-config)# set band-amc-release-timer <val> The command allows the user to update the parameter that defines the minimum required number of frames to measure the average and standard deviation for the event of Band AMC triggering. A FullMax(ul-config)#show band-amc-release-timer The command allows the user to display parameter that defines the minimum required number of frames to measure the average and standard deviation for the event of Band AMC triggering. A/O Example: FullMax(ul-config)#set band-amc-release-timer 22 Updated band-amc-release-timer 22 Frames FullMax(ul-config)#show band-amc-release-timer band-amc-release-timer 22 Frames bandbandbandband----amcamcamcamc----retryretryretryretry----timertimertimertimer Backoff timer between consecutive mode transitions from normal subchannel to Band AMC when the previous request is failed. Command Purpose Privileges FullMax(ul-config)#set band-amc-retry-timer <val> The command allows the user to update the parameter band AMC retry timer A FullMax(ul-config)#show band-amc-retry-timer The command allows the user to display parameter band AMC retry timer. A/O Example: FullMax(ul-config)# set band-amc-retry-timer 5 Updated band-amc-retry-timer 5 FullMax(ul-config)# show band-amc-retry-timer band-amc-retry-timer 5 bandbandbandband----statstatstatstat----reprepreprep----maxmaxmaxmax----periodperiodperiodperiod Maximum period between refreshing the Band CINR measurement by the unsolicited REP-RSP. Command Purpose Privileges FullMax(ul-config)# set band-stat-rep-max-period <val> The command allows the user to update the maximum period between refreshing the Band CINR measurement by the unsolicited REP-RSP. A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 36FullMax(ul-config)# show band-stat-rep-max-period The command allows the user to display the maximum period between refreshing the Band CINR measurement by the unsolicited REP-RSP. A/O Example: FullMax(ul-config)# set band-stat-rep-max-period 12 Updated band-stat-rep-max-period 12 FullMax(ul-config)# show band-stat-rep-max-period band-stat-rep-max-period 12 upupupup----powerpowerpowerpower----adjadjadjadj----stepstepstepstep MS specific up power offset adjustment step. Command Purpose Privileges FullMax(ul-config)#set band-stat-rep-max-period <val> The command allows the user to update the maximum period between refreshing the Band CINR measurement by the unsolicited REP-RSP. A FullMax(ul-config)#show band-stat-rep-max-period The command allows the user to display the maximum period between refreshing the Band CINR measurement by the unsolicited REP-RSP. A/O Example: FullMax(ul-config)# set up-power-adj-step 12 Updated up-power-adj-step 12 (in 0.01 dB). FullMax(ul-config)# show up-power-adj-step up-power-adj-step 12 (in 0.01 dB). down-power-offset-adj-step MS specific down power offset adjumstment step. Command Purpose Privileges FullMax(ul-config)# set down-power-offset-adj-step <val> The command allows the user to update the MS specific down power offset adjustment step. A FullMax ul-config)# show down-power-offset-adj-step The command allows the user to display the MS specific down power offset adjustment step. A/O Example: FullMax(ul-config)# set down-power-offset-adj-step 6
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 37 Updated down-power-offset-adj-step 6 (in 0.01 dB). FullMax(ul-config)# show up-power-offset-adj-step up-power-offset-adj-step 6 (in 0.01 dB). min-power-offset-adj Minimum level of power offset adjustment. Command Purpose Privileges FullMax(ul-config)# set min-power-offset-adj <val> The command allows the user to update the value of Minimum level of power offset adjustment. A FullMax(ul-config)#show min-power-offset-adj The command allows the user to display the value of Minimum level of power offset adjustment. A/O Example: FullMax(ul-config)# set min-power-offset-adj 2 Updated min-power-offset-adj 2 (in 0.01 dB). FullMax(ul-config)# show min-power-offset-adj min-power-offset-adj 2 (in 0.01 dB). maxmaxmaxmax----powerpowerpowerpower----offsetoffsetoffsetoffset----adjadjadjadj Maximum level of power offset adjustment. Command Purpose Privileges FullMax(ul-config)#set max-power-offset-adj <val> The command allows the user to update the value of maximum level of power offset adjustment. A FullMax(ul-config)#show max-power-offset-adj The command allows the user to display the value of maximum level of power offset adjustment. A/O Example: FullMax (ul-config) # set max-power-offset-adj 16 Updated max-power-offset-adj 16 (in 0.01 dB). FullMax (ul-config) # show max-power-offset-adj max-power-offset-adj 16 (in 0.01 dB). initialinitialinitialinitial----rngrngrngrng----backoffbackoffbackoffbackoff----startstartstartstart Initial backoff window size for initial ranging connection, expressed as a power of 2. Command Purpose Privileges FullMax(ul-config)# set intial-rng-backoff-start The command allows the user to update the value of initial backoff window size for initial ranging connection. A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 38<val> FullMax(ul-config)#show intial-rng-backoff-start The command allows the user to display the value of initial backoff window size for initial ranging connection. A/O Example: FullMax(ul-config)# set intial-rng-backoff-start 2 Updated intial-rng-backoff-start 2 FullMax(ul-config)# show intial-rng-backoff-start intial-rng-backoff-start 2 initialinitialinitialinitial----rngrngrngrng----backoffbackoffbackoffbackoff----endendendend Final backoff window size for initial ranging connection, expressed as a power of 2. Command Purpose Privileges FullMax(ul-config)# set intial-rng-backoff-end <val> The command allows the user to update the value of final backoff window size for initial ranging connection. A FullMax(ul-config)# show intial-rng-backoff-end The command allows the user to display the value of final backoff window size for initial ranging connection. A/O Example: FullMax(ul-config)# set intial-rng-backoff-end 8 Updated intial-rng-backoff-end 8 FullMax(ul-config)# show intial-rng-backoff-end intial-rng-backoff-end 8 bwbwbwbw----reqreqreqreq----backoffbackoffbackoffbackoff----startstartstartstart Initial backoff window size for contention bandwidth requests, expressed as a power of 2. Command Purpose Privileges FullMax(ul-config)# set bw-req-backoff-start <val> The command allows the user to update the value of initial backoff window size for contention bandwidth requests. A FullMax(ul-config)#show bw-req-backoff-start The command allows the user to display the value of initial backoff window size for contention bandwidth requests. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 39 Example: FullMax(ul-config)#set bw-req-backoff-start 4 Updated bw-req-backoff-start 4 FullMax(ul-config)#show bw-req-backoff-start bw-req-backoff-start 4 bwbwbwbw----reqreqreqreq----backoffbackoffbackoffbackoff----endendendend Final backoff window size for contention bandwidth requests, expressed as a power of 2. Command Purpose Privileges FullMax(ul-config)# set bw-req-backoff-end <val> The command allows the user to update the value of final backoff window size for contention bandwidth requests. A FullMax(ul-config)# show bw-req-backoff-end The command allows the user to display the value of final backoff window size for contention bandwidth requests. A/O Example: FullMax(ul-config)# set bw-req-backoff-end 8 Updated bw-req-backoff-end 4 FullMax(ul-config)# show bw-req-backoff-end bw-req-backoff-end 4 allallallall This command displays all the parameter values of tables supported in this group. Command Purpose Privileges FullMax(ul-config)# show all The command allows the user to display the value of all the MIB parameters of tables supported in this group. A/O Example: FullMax(ul-config)# show all ct-based-reserve-timeout 200 uplink-center-frequency 200 init-rng-codes 0 periodic-rng-codes 50 bandwidth-request-codes 0 per-rng-backoff-start 20 permutation-base 0 ul-alloc-sub-channel-bitmap 3 band-amc-alloc-threshold 60 db band-amc-release-threshold 0 db
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 40band-amc-alloc-timer 255 Frames band-amc-release-timer 0 Frames 5.2.4 dl-config The group defines the commands that monitors or updates the DCD channel attributes that define the characteristics of downlink channel. The user upon entering the dl-config command locks into the CLI to execute commands only related to BS downlink channel characteristics. FullMax# FullMax# dl-config FullMax(dl-config)# Command Purpose Privileges FullMax# dl-config The command allows the user to lock into the group dl-config and execute all the commands related to the group. A/O dldldldl----channelchannelchannelchannel----tabletabletabletable This command Displays the values of all the commands affiliated to dl-channel-table in the dl-config group. Command Purpose Privileges FullMax(dl-config)#show dl-channel-table The command allows the user to display the DL Channel table MIB parameter values. A/O Example: FullMax(dl-config)# show dl-channel-table bs-eirp 244 dBm downlink-center-frequency 244 khz bsid 00f401:0000f4 hysterisis-margin 45 dB time-to-trigger 2 milliseconds frameframeframeframe----durationdurationdurationduration----codecodecodecode The duration of the frame Command Purpose Privileges FullMax(dl-config)#set frame-duration-code The command allows the user to update the OFDMA frame duration code. A FullMax(dl-config)#show frame-duration-code The command allows the user to display the OFDMA frame duration code. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 41Example: FullMax(dl-config)# set frame-duration-code 12 updated frame-duration-code 12 FullMax(dl-config)# show frame-duration-code frame-duration-code 12 bsbsbsbs----eirpeirpeirpeirp The EIRP is the equivalent isotropic radiated power of the base station, which computed for a simple single-antenna transmitter. Command Purpose Privileges FullMax(dl-config)#set bs-eirp <val> The command allows the user to update the BS EIRP parameter A FullMax(dl-config)#show bs-eirp The command allows the user to display the BS EIRP parameter A/O Example: FullMax(dl-config)# set bs-eirp 3770 Updated bs-eirp 3770 dBm FullMax(dl-config)# show bs-eirp bs-eirp 3770 dBm downlinkdownlinkdownlinkdownlink----centercentercentercenter----frequencyfrequencyfrequencyfrequency Downlink center frequency (Khz). Command Purpose Privileges FullMax(dl-config)# set downlink-center-frequency <val> The command allows the user to update the downlink center frequency. A FullMax(dl-config)#show downlink-center-frequency The command allows the user to display the downlink center frequency. A/O Example: FullMax (dl-config)# set downlink-center-frequency 11000 Updated downlink-center-frequency 11000 kHz FullMax(dl-config)# show downlink-center-frequency downlink-center-frequency 11000 kHz.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 42 bsidbsidbsidbsid Defines the encoding of BSID. The BSID is a 6 byte number and follows the encoding rules of MacAddress textual convention, e.e as if it were transmitted least-significant bit first. The value should be displayed with 2 parts clearly separated by a colon e.g : 001DFF:00003A. The most significant part is representing the operator ID. Command Purpose Privileges FullMax(dl-config)# set bsid <val> The command allows the user to update the BS ID A FullMax(dl-config)#show bsid The command allows the user to display the BS ID A/O Example: FullMax(dl-config)# set bsid 0A30A1:10FE11 Updated bsid 0A30A1:10FE11 FullMax(dl-config)# show bsid bsid 0A30A1:10FE11 bandwidthbandwidthbandwidthbandwidth Channel Bandwidth in Khz Command Purpose Privileges FullMax(dl-config)# set bandwidth <val> The command allows the user to updates the channel bandwidth. A FullMax(dl-config)#show bandwidth The command allows the user to display the channel bandwidh. A/O Example: FullMax(dl-config)# set bandwidth 400 Updated bandwidth 400 KHz FullMax(dl-config)# show bandwidth bandwidth 400 KHz SamplingSamplingSamplingSampling----clockclockclockclock Sampling clock for the channel Command Purpose Privileges FullMax(dl-config)#set sampling-clock <val> The command allows the user to updates the sampling clock. A FullMax(dl-config)#show sampling-clock The command allows the user to display the sampling clock. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 43 Example: FullMax(dl-config)# set sampling-clock 12800 Updated sampling-clock 12800 KHz FullMax(dl-config)# show sampling-clock sampling-clock 12800 KHz filterfilterfilterfilter----idididid The ID of the PHY filter to use for this channel Command Purpose Privileges FullMax(dl-config)# set filter-id <val> The command allows the user to updates the filter id. A FullMax(dl-config)#show filter-id The command allows the user to display the filter id. A./O Example: FullMax(dl-config)# set filter-id 1 Updated filter-id 1 FullMax(dl-config)# show filter-id filter-id 1 fft_sizefft_sizefft_sizefft_size FFT size for OFDMA PHY Command Purpose Privileges FullMax(dl-config)# set fft_size <val> The command allows the user to updates the fft_size. A FullMax(dl-config)#show fft_size The command allows the user to display the fft_size A/O Example: FullMax (dl-config)# set fft_size 512 Updated fft_size 512 FullMax (dl-config) # show fft_size fft_size 512 dl_framedl_framedl_framedl_frame----durationdurationdurationduration This field indicates the number of OFDMA symbols allocated for downlink transmission in the OFDMA frame Command Purpose Privileges FullMax(dl-config)# set dl_frame-duration <val> The command allows the user to updates the downlink frame duration A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 44FullMax(dl-config)# show dl_frame-duration The command allows the user to display the downlink frame duration A/O Example: FullMax (dl-config)# set dl_frame-duration 20 Updated dl_frame-duration 20 ofdma symbols FullMax (dl-config) # show dl_frame-duration dl_frame-duration 20 ofdma symbols ul_frameul_frameul_frameul_frame----durationdurationdurationduration This field indicates the number of OFDMA symbols allocated for uplink transmission in the OFDMA frame. Command Purpose Privileges FullMax(dl-config)# set ul_frame-duration <val> The command allows the user to updates the uplink frame duration. A FullMax(dl-config)#show ul_frame-duration The command allows the user to display the uplink frame duration. A/O Example: FullMax (dl-config)# set ul_frame-duration 10 Updated ul_frame-duration 10 ofdma symbols FullMax (dl-config) # show ul_frame-duration ul_frame-duration 10 ofdma symbols dl_zones_numdl_zones_numdl_zones_numdl_zones_num Number of downlink zones for the BS Command Purpose Privileges FullMax(dl-config)#set dl_zones_num <val> The command allows the user to update the number of downlink zones. A FullMax(dl-config)#show dl_zones_num The command allows the user to display the number of downlink zones. A/O Example: FullMax (dl-config)# set dl_zones_num 2 Updated dl_zones_num 2 zones FullMax (dl-config) # show dl_zones_num dl_zones_num 2 zones
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 45ul_zones_numul_zones_numul_zones_numul_zones_num Number of uplink zones for the BS Command Purpose Privileges FullMax(dl-config)# set ul_zones_num <val> The command allows the user to updates the number of uplink zones A FullMax(dl-config)#show ul_zones_num The command allows the user to display the number of uplink zones. A/O Example: FullMax(dl-config)# set ul_zones_num 2 Updated ul_zones_num 2 zones FullMax (dl-config)# show ul_zones_num ul_zones_num 2 zones 5.2.5 zone-config The group defines the commands that monitors or updates the downlink and uplink zones attributes. The user upon entering the zone-config command locks into the CLI to execute commands only related to BS downlink and uplink zones characteristics. FullMax# FullMax# zone-config FullMax(zone-config)# Command Purpose Privileges FullMax# zone-config The command allows the user to lock into the group zone-config and execute all the commands related to the group. A/O dldldldl----zonezonezonezone----idididid The downlink zone identifier ,the index of the first zone will always be 0 Command Purpose Privileges FullMax(zone-config)#show dl-zone-id The command allows the user to display the avaliable DL zone ids. A/O Example: FullMax(zone-config)#show dl-zone-id dl-zone-id 0 dl-zone-id 1
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 46 dl-zone-id 2 dldldldl----zonezonezonezone----tabletabletabletable This table contains zone attributes that characterize a downlink zone Command Purpose Privileges FullMax(zone-config)# show dl_zone-table The command allows the user to display the list of downlink zones. A/O FullMax(zone-config)# show dl-zone-table 2 dl-zone-stc 0 dl-perm-type pusc dl-perm-base 17 dl-start-symbol 11 dl-all-sc YES dl-cinr-threshold 2 dB dldldldl----permpermpermperm----typetypetypetype Permutation type of this zone Command Purpose Privileges FullMax(zone-config)# set dl-perm-type <id> <val> The command allows the user to update the downlink permutation type of zone <id> A FullMax(zone-config)# show dl-perm-type <id> The command allows the user to display the permutation type of zone <id> A/O Example: FullMax(zone-config)# set dl-perm-type 0 1 Updated dl-perm-type of zone 0 to pusc (1) FullMax(zone-config)# show dl-perm-type 0 dl-perm-type of zone 0 is pusc (2) dldldldl----zonezonezonezone----stcstcstcstc Downlink zone Command Purpose Privileges FullMax(zone-config)# set dl-perm-zone <zone-id> <val> The command allows the user to update the downlink permutation zone of zone <zone-id> A FullMax(zone-config)#show The command allows the user to A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 47dl-perm-zone <zone-id> display the permutation zone of zone <zone-id> Example: FullMax(zone-config)# set dl-zone-stc 0 2 Updated dl-zone-stc of zone 0 to nonstc (2) FullMax(zone-config)# show dl-zone-stc 0 dl-zone-stc of zone 0 is nonstc (2) dldldldl----permpermpermperm----basebasebasebase Permutation base for this zone Command Purpose Privileges FullMax(zone-config)# set dl-perm-base <id> <val> The command allows the user to update the downlink permutation base of zone <id> A FullMax(zone-config)# show dl-perm-base <id> The command allows the user to display the permutation base of zone <id> A/O Example: FullMax(zone-config)# set dl-perm-base 0 17 Updated dl-perm-base of zone 0 to 17 FullMax(zone-config)# show dl-perm-base dl-perm-base of zone 0 is 17 dldldldl----startstartstartstart----symbolsymbolsymbolsymbol Index of the starting symbol for this zone. Command Purpose Privileges FullMax(zone-config)# set dl-start-symbol <zone-id> <val> The command allows the user to update the start-symbol downlink of <zone-id> A FullMax(zone-config)#show dl-start-symbol <zone-id> The command allows the user to display the start-symbol of <zone-id> A/O Example: FullMax (zone-config)# set dl-start-symbol 0 5 Updated dl-perm-type of zone 0 to 5 FullMax(zone-config)# show dl-start-symbol dl-start-symbol of zone 0 is 5 dldldldl----allallallall----scscscsc
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 48Use all subchannels. 1 (true): use_all_SC=1 2 (false): use_all_SC=0 Downlink zone parameters – Command Purpose Privileges FullMax (zone-config)#set dl-all-sc <zone-id> <val> The command allows the user to update the downlink zone–all-subchannels parameter A FullMax(zone-config)#show dl-all-sc <zone-id> The command allows the user to display the all subchannels parameter of <zone-id> A/O Example: FullMax(zone-config)# set dl-all-sc 0 YES Updated dl-all-sc of zone 0 to YES FullMax (zone-config) # show dl-all-sc 0 dl-all-sc of zone 0 is YES dldldldl----cinrcinrcinrcinr----thresholdthresholdthresholdthreshold Threshold of the maximum of the standard deviations of the individual bands CINR measurements over time to trigger mode transition from zone 0 to this zone. Command Purpose Privileges FullMax(zone-config)# set dl-cinr-threshold <zone-id> <val> The command allows the user to update the CINR threshold for <zone-id> A FullMax(zone-config)#show dl-cinr-threshold <zone-id> The command allows the user to display the CINR threshold for <zone-id> A/O Example: FullMax(zone-config)# set dl- cinr-threshold 0 2 Updated dl-cinr-threshold of zone 0 to 2 dB FullMax(zone-config)# show dl-cinr-threshold 0 dl-cinr-threshold of zone 0 is 2 dB ulululul----ZoneZoneZoneZone----idididid The uplink zone identifier , The index of the first uplink zone will always be 0 Command Purpose Privileges FullMax(zone-config)# show ul-zone-id The command allows the user to display the ul zone indixes avaliable A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 49 Example: FullMax(zone-config)#show ul-zone-id ul-zone-id 0 ul-zone-id 1 ul-zone-id 2 ul-zone-table Displays the Uplink zones table Command Purpose Privileges FullMax(zone-config)#show ul_zone-table The command allows the user to display the list of uplink zones. A/O Example: FullMax(zone-config)# show ul-zone-table 0 ul-perm-type for zone-id (0) : nonstc(2) ul-perm-base for zone-id (0) : 17 ul-start-symbol for zone-id (0) : 11 ul-alloc-bitmap for zone-id (0) : 3 ul-cinr-threshold for zone-id (0) : 2 dB ul-perm-type A zone permutation type Command Purpose Privileges FullMax(zone-config)#set ul-perm-type <id> <val> The command allows the user to update the uplink permutation type of <zone-id> A FullMax(zone-config)#show ul-perm-type <id> The command allows the user to display the permutation type of zone <zone-id> A/O Example: FullMax(zone-config)# set ul-perm-type 0 2 Updated ul-perm-type for zone-id(0): to non-stc (2) FullMax(zone-config)# show ul-perm-type 0 ul-perm-type for zone-id (0) : non-stc (2) ul-perm-base Determines the Permutation Base parameter for the zone, permutation to be used on this uplink zone Command Purpose Privileges
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 50FullMax(zone-config)# set ul-perm-base <id> <val> The command allows the user to update the uplink permutation base of <zone-id> A FullMax(zone-config)#show ul-perm-base <id> The command allows the user to display the permutation base of <zone-id> A/O Example: FullMax(zone-config)# set ul-perm-base 0 17 Updated ul-perm-base for zone-id (0) to 17 FullMax (zone-config) # show ul-perm-base ul-perm-base for zone-id (0) : 17 ul-start-symbol Index of the starting symbol for this zonehat segment Command Purpose Privileges FullMax(zone-config)# set ul-start-symbol <zone-id> <val> The command allows the user to update the start-symbol uplink of <zone-id> A FullMax(zone-config)# show ul-start-symbol <zone-id> The command allows the user to display the start-symbol of <zone-id> A/O Example: FullMax (zone-config)# set ul-start-symbol 0 5 Updated ul-start-symbol for zone-id (0) to 5 FullMax (zone-config) # show ul-start-symbol ul-start-symbol for-id zone-id(0) :5 ul-alloc-bitmap This is a bitmap describing the physical sub-channels allocated to the segment in the UL, when using the uplink PUSC permutation. The LSB of the first byte shall corrspond to subchannel 0. For any bit that is not set, the corresponding subchannel shall not be used by the SS on that segment Command Purpose Privileges FullMax(zone-config)# set ul-alloc-bitmap <zone-id> <val> The command allows the user to update the uplink zone – allocation bitmap parameter A FullMax(zone-config)#show ul-alloc-bitmap <zone-id> The command allows the user to display the allocation bitmap parameter of zone <id> A/O Example:
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 51 FullMax(zone-config)# set ul-alloc-bitmap 0 010101 Updated ul-alloc-bitmap for zone-id (0) : to 010101 FullMax(zone-config) # show ul-alloc-bitmap 0 ul-alloc-bitmap of zone-id (0) : 01010101 ul-cinr-threshold This object is used to ensure that the write operation to multiple columns is guaranteed to be treated as atomic operation by agent. Command Purpose Privileges FullMax(zone-config)# set ul-cinr-threshold <zone-id> <val> The command allows the user to update the CINR threshold for zone <id> A FullMax(zone-config)# show ul-cinr-threshold <zone-id> The command allows the user to display the CINR threshold for zone <id> A/O Example: FullMax(zone-config)# set ul-cinr-threshold 0 2 Updated ul-cinr-threshold for zone-id (0) to 2 dB FullMax(zone-config)# show ul-cinr-threshold 0 ul-cinr-threshold for zone-id (0): 2 dB 5.2.6 bs-cap-config The group defines the commands to configure the basic capabilities of BS. The user upon entering the bs-capability-config command locks into the CLI to execute commands only related to basic capabilities of BS. FullMax# FullMax# bs-cap-config FullMax(bs-cap-config)# Command Purpose Privileges FullMax# bs-cap-config The command allows the user to lock into the group bs-cap-config and execute all the commands related to the group. A/O all Description Command Purpose Privileges FullMax(bs-cap- The command allows the user to A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 52onfig)#show all display values of all the attributes of bs-cap-config group Example: FullMax(bs-cap-config)# show all capability-ttg-transition-gap 34 microseconds capability-rtg-transition-gap 34 microseconds capability-pn-window-size 1000 capability-number-of-ul-harq-channel 0 capability-number-of-dl-harq-channel 0 Capability-ttg-transition-gap This parameter indicates the configured transition speed SSTTG for TDD and H-FDD SSs. The usage is defined by ss-transistion-gap Command Purpose Privileges FullMax(bs-cap-config)# set capability-ttg-transitio-gap <val> The command allows the user to update the TTG transition gap parameter A FullMax(bs-cap-config)# show capability-ttg-transitio-gap The command allows the user to display the TTG transition gap parameter A/O Example: FullMax(bs-cap-config)# set capability-ttg-transitio-gap <val> Updated capability-ttg-transitio-gap FullMax(bs-cap-config)# show capability-ttg-transitio-gap capability-ttg-transitio-gap Capability-rtg-transition-gap This parameter indicates the configured transition speed SSTTG for TDD and H-FDD SSs. The usage is defined by ss-transition-gap. Command Purpose Privileges FullMax(bs-cap-config)# set capability-rtg-transition-gap <val> The command allows the user to update the RTG transition gap. A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 53FullMax(bs-cap-config)#show capability-rtg-transition-gap The command allows the user to display the RTG transition gap. A/O Example: FullMax(bs-cap-config)# set capability-rtg-transition-gap 30 Updated capability-rtg-transition-gap FullMax (bs-cap-config)# show capability-rtg-transition-gap capability-rtg-transition-gap 30 5.2.7 bs-burst-profile The group defines the commands to burst profile commands of BS. The user upon entering the bs-burst-profile command locks into the CLI to execute commands only related to BS burst profile of BS. FullMax# FullMax# bs-burst-profile FullMax(bs-burst-profile)# Command Purpose Privileges FullMax#bs-burst-profile The command allows the user to lock into the group bs-burst-profile and execute all the commands related to the group. A/O uiuc-index The uplink interval usage code inidicates the uplink burst profile in the ucd message and is used along the index to identify the ucd-fec-code. Max uiuc -index range for OFDMA PHY <0- 10 > Command Purpose Privileges FullMax(bs-burst-Profile)# show uiuc-index The command allows the user to display the Uplink intetrval usage codes indexes avaliable in the MAC A/O Example: FullMax(bs-burst-profile)# show uiuc-index uiuc-index 0 uiuc-index 1 uiuc-index 2 uiuc-index 3
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 54ucd-fec-code-type Uplink FEC code type and modulation type Command Purpose Privileges FullMax (bs-burst-rofile)# show dcd-fec-code-type <uiuc-index> The command allows the user to display the different FEC and coding options for uplink burst profile. A/O Example: FullMax(bs-burst-profile)# show ucd-fec-code-type 1 ucd-fec-code-type for uiuc-index (1) : qpskCc1Over2(0), qpskCc3Over4(1), sixteenQamCc1Over2(2), sixteenQamCc3Over4(3), sixtyFourQamCc1Over2(4), sixtyFourQamCc2Over3(5), sixtyFourQamCc3Over4(6), qpskBtc1Over2(7), qpskBtc3Over4Or2Over3(8), sixteenQamBtc3Over5(9), sixteenQamBtc4Over5(10), sixtyFourQamBtc2Over3Or5Over8(11), sixtyFourQamBtc5Over6Or4Over5(12), qpskCtc1Over2(13), reserved14(14), qpskCtc3Over4(15), sixteenQamCtc1Over2(16), sixteenQamCtc3Over4(17), sixtyFourQamCtc1Over2(18), sixtyFourQamCtc2Over3(19), sixtyFourQamCtc3Over4(20), sixtyFourQamCtc5Over6(21), qpskZtCc1Over2(22), qpskZtCc3Over4(23), sixteenQamZtCc1Over2(24), sixteenQamZtCc3Over4(25), sixtyFourQamZtCc1Over2(26), sixtyFourQamZtCc2Over3(27), sixtyFourQamZtCc3Over4(28), qpskLdpc1over2(29), qpskLdpc2over3A(30), qpskLdpc3over4A(31), sixteenQamLdpc1over2(32), sixteenQamLdpc2over3A(33), sixteenQamLdpc3over4A(34), sixtyFourQamLdpc1over2(35), sixtyFourQamLdpc2over3A(36), sixtyFourQamLdpc3over4A(37), qpskLdpc2over3B(38), qpskLdpc3over4B(39), sixteenQamLdpc2over3B(40), sixteenQamLdpc3over4B(41), sixtyFourQamLdpc2over3B(42), sixtyFourQamLdpc3over4B(43), qpskCcOptIntv1over2(44), qpskCcOptIntv3over4(45), sixteenQamCcOptIntv1over2(46), sixteenQamCcOptIntv3over4(47), sixtyFourQamCcOptIntv2over3(48), sixtyFourQamCcOptIntv3over4(49), qpskLdpc5over6(50), sixteenQamLdpc5over6(51), sixtyFourQamLdpc5over6(52) diuc-index
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 55The Downlink interval usage code inidicates the uplink burst profile in the ucd message and is used along the index to identify the Dcd-fec-code. Max diuc -index range for OFDMA PHY <0- 12 > Command Purpose Privileges FullMax(bs-burst-Profile)# show diuc-index The command allows the user to display the Downlink interval usage codes indexes avaliable in the MAC A/O Example: FullMax(bs-burst-profile)# show diuc index diuc-index 0 diuc-index 1 diuc-index 2 diuc-index 3 dcd-fec-code-type Displays FEC and coding options for downlink burst profiles Command Purpose Privileges FullMax (bs-burst-profile)# show dcd-fec-code-type <diuc-index> The command allows the user to display the different FEC and coding options for downlink burst profile. A/O Example: FullMax (bs-burst-profile) # show dcd-fec-code-type 2 dcd-fec-code-type for dicu-index (2) is qpskCc1Over2(0), qpskCc3Over4(1), sixteenQamCc1Over2(2), sixteenQamCc3Over4(3), sixtyFourQamCc1Over2(4), sixtyFourQamCc2Over3(5), sixtyFourQamCc3Over4(6), qpskBtc1Over2(7), qpskBtc3Over4Or2Over3(8), sixteenQamBtc3Over5(9), sixteenQamBtc4Over5(10), sixtyFourQamBtc2Over3Or5Over8(11), sixtyFourQamBtc5Over6Or4Over5(12), qpskCtc1Over2(13), reserved14(14), qpskCtc3Over4(15), sixteenQamCtc1Over2(16), sixteenQamCtc3Over4(17), sixtyFourQamCtc1Over2(18), sixtyFourQamCtc2Over3(19), sixtyFourQamCtc3Over4(20), sixtyFourQamCtc5Over6(21), qpskZtCc1Over2(22), qpskZtCc3Over4(23), sixteenQamZtCc1Over2(24), sixteenQamZtCc3Over4(25), sixtyFourQamZtCc1Over2(26), sixtyFourQamZtCc2Over3(27),
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 56sixtyFourQamZtCc3Over4(28), qpskLdpc1over2(29), qpskLdpc2over3A(30), qpskLdpc3over4A(31), sixteenQamLdpc1over2(32), sixteenQamLdpc2over3A(33), sixteenQamLdpc3over4A(34), sixtyFourQamLdpc1over2(35), sixtyFourQamLdpc2over3A(36), sixtyFourQamLdpc3over4A(37), qpskLdpc2over3B(38), qpskLdpc3over4B(39), sixteenQamLdpc2over3B(40), sixteenQamLdpc3over4B(41), sixtyFourQamLdpc2over3B(42), sixtyFourQamLdpc3over4B(43), qpskCcOptIntv1over2(44), qpskCcOptIntv3over4(45), sixteenQamCcOptIntv1over2(46), sixteenQamCcOptIntv3over4(47), sixtyFourQamCcOptIntv2over3(48), sixtyFourQamCcOptIntv3over4(49), qpskLdpc5over6(50), sixteenQamLdpc5over6(51), sixtyFourQamLdpc5over6(52) 5.2.8 bs-ss-action The bs-ss-action group define the commands that monitors or updates the actions specified for SS. The user upon entering the bs-ss-action command locks into the CLI to execute commands only related to BS private mib. FullMax# FullMax#bs-ss-action FullMax(bs-ss-action)# Command Purpose Privileges FullMax#bs-ss-action The command allows the user to lock into the group bs-ss-action and execute all the commands related to the group. A/O reset-ss Reset action performed on SS. Command Purpose Privileges FullMax(bs-ss-action)#set reset-ss <mac-address> The command allows the user to perform reset action on SS A Example: FullMax(bs-ss-action)# set reset-ss 1 0A1234:5678AB Reset-ss message sent to 0A1234:5678AB abort-ss Abort action performed on SS.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 57Command Purpose Privileges FullMax(bs-ss-action)#set abort-ss <abort-op> <mac-address> [-d:dl-freq] [-u:up-id] The command allows the user to perform the abort action on SS A/O FullMax(bs-ss-action)# set abort-ss 1 <mac-address> abort-ss message sent to <mac-address> FullMax(bs-ss-action)# set abort-ss 2 0A1234:5678AB -d:210000 abort-ss message with downlink frequency override 210000 KHz sent to 0A1234:5678AB de-reg-ss De-registration action on SS Command Purpose Privileges FullMax(bs-ss-action)# set abort-ss <abort-op> <mac-address> [-d:dl-freq] [-u:up-id] The command allows the user to perform the abort action on SS A/O FullMax(bs-ss-action)# set de-reg-ss 0A1234:5678AB 2 De-reg-ss message sent to 0A1234:5678AB with limited transmission code (2) FullMax(bs-ss-action)# set de-reg-ss 0A1234:5678AB 1 De-reg-ss message sent to 0A1234:5678AB with no transmission code (1) 5.2.9 ss-registered The ss-registered group defines the commands that monitors or updates the standard mib related information. The user upon entering the ss-registered command locks into the CLI to execute commands only related to SS registered table mib. FullMax# FullMax# ss-registered FullMax ss-registered)# Command Purpose Privileges FullMax# ss-registered The command allows the user to lock into the group ss-registered and execute all the commands related to the group. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 58ss-mac-addresss The MAC address of SS is received in the RNG-REQ message when SS registers ,this MAC address is entered in to the Bs Registered Ss Table. Command Purpose Privileges FullMax(ss-registered)# show registered-ss-mac-address The command allows the user display all the SS MAC addresses. A/O Example: FullMax(ss-registered)# show registered-ss-mac-address Registered SS MAC Addresses are: registered-ss-mac-address 1 001BFE:01020A registered-ss-mac-address 2 001BAA:01030F registered-ss-mac-address 3 001BEF:01F01A max-tx-power-qpsk SS’s Maximum available power for QPSK in dBm. This parameter is only applicable to systems supporting the SCa, OFDM or OFDMA PHY. Command Purpose Privileges FullMax(ss-registered)# show max-tx-power-qpsk <Key> The command allows the user display SS’s Maximum available power for QPSK in dBm. Here key is SS’s MAC address. A/O Example: FullMax(ss-registered)# show max-tx-power-qpsk 001BFE:01020A max-tx-power-qpsk 27 dBm max-tx-power-16qam SS’s Maximum available power for 16-QAM constellations in dBm. This parameter is only applicable to systems supporting the SCa, OFDM or OFDMA PHY. Command Purpose Privileges FullMax(ss-registered)# show max-tx-power-16qam <key> The command allows the user display SS’s Maximum available power for 16QAM in dBm. Here key is SS’s MAC address. A/O Example:
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 59FullMax(ss-registered)# show max-tx-power-16qam 001BAA:01030F max-tx-power-16qam 20 dBm max-tx-power-64qam SS’s Maximum available power for 64-QAM constellations in dBm. This parameter is only applicable to systems supporting the SCa, OFDM or OFDMA PHY. Command Purpose Privileges FullMax(ss-registered)# show max-tx-power-64qam <key> The command allows the user display SS’s Maximum available power for 64QAM in dBm. Here key is SS’s MAC address. A/O Example: FullMax(ss-registered)# show max-tx-power-64qam 001BEF:01F01A max-tx-power-64qam 25 dBm 5.2.10 ss-ip The bs-ss-ip group define the commands that monitors or updates the BsSsIp related information. The user upon entering the ss-ip command locks into the CLI to execute commands only related to BsSsIpTable defined in the private mib. FullMax# FullMax# ss-ip FullMax(ss-ip)# Command Purpose Privileges FullMax# ss-ip The command allows the user to lock into the group ss-ip and execute all the commands related to the group. A/O ss-ip-table This table contains the IP configuration information of Subcriber station's as set by DHCP Relay function in the Base Station. Command Purpose Privileges FullMax(ss-ip)#show ss-ip-table The command allows the user display the MS IP table. A/O Example: FullMax (bs-private) # show ss-ip-table 001BFE:01020A ss-mac-address 001BFE:01020A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 60 ss-ip-address 192.168.0.1 ss-subnet-mask 192.168.0.0 ss-mac-address The MAC address of SS is received from the RNG-REQ message. When SS registers, this MAC address is entered into the table, and used as the identifier to the SS. Command Purpose Privileges FullMax (ss-ip) # show ss-mac-address The command allows the user display the MS MAC address of all MS. A/O Example: FullMax (ss-ip) # show ss-mac-address ss-mac-addres 00A1B3:01AB03 ss-mac-addres 00A1B3:010203 ss-mac-addres 00A1B3:010405 ss-ip-address The subnet mask address of SS as received from BS DHCP Relay. When SS Registers, this IP address is entered into the table, and used as the identifier to the SS. Command Purpose Privileges FullMax (ss-ip) # show ss-ip-address The command allows the user display the IP address. A/O Example: FullMax(ss-ip)# show ss-ip-address 00A1B3:01AB03 ss-ip-addres 192.168.0.1 ss-subnet-mask The IP address of SS is received from the DHCP-Relay in the BS when SS register, this IP address is entered into the table, and used as the identifier to the SS. Command Purpose Privileges FullMax(ss-ip)#show ss-ip-address The command allows the user display the subnet mask of all the MS. A/O Example: FullMax(ss-ip)# show ss-subnet-mask 00A1B3:01AB03 ss-subnet-mask 192.168.0.0
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 615.2.11 device The device group define the commands that monitors or updates the device related information in the private MIB. The user upon entering the device command locks into the CLI to execute commands only related to device. FullMax# FullMax# device FullMax(device)# Command Purpose Privileges FullMax# device The command allows the user to lock into the group device and execute all the commands related to the group. A/O type Type of device (BS/MS/SS). Command Purpose Privileges FullMax(device)# show type The command allows the user display the device type (BS/MS/SS) A/O Example: FullMax(device)# show type type BS gpos The geographical position of the device , i.e. the real number describing the longitude and latitusde encoded as a printable string. Longitude - the precision is within the range -90..90 degrees.Positive numbers indicate locations north of the equator. Latitude - The precision is within the range -180..180 degrees.Positive numbers indicate locations east of the prime meridian Command Purpose Privileges FullMax(device)# set gpos <val> The command allows the user to update the geographical position of the device A FullMax(device)# show gpos The command allows the user display geographical position of the device. A/O Example: FullMax(device)# set gpos 64.000 88.3400 updated gpos 64.000 88.3400
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 62 FullMax(device) # show gpos gpos 64.000 88.3400 boot-time The absolute time of last device boot up. Command Purpose Privileges FullMax(device)# show boot-time The command allows the user display the device boot up time. A/O Example: FullMax(device)# show boot-time boot-time 230404:18052008 commit-save Setting this object to TRUE causes the device to write all configuration changes in FLASH memory. On next boot the changes will be relevant. If this operation does not occur, configuration changes will not be maintained through reset Reading this object always returns FALSE Command Purpose Privileges FullMax(device)# set commit-save <val> The command allows the user update the commit-save to TRUE . A FullMax(device)# show commit-save The command allows the user display the commit-save A/O Example: FullMax(device)# set commit-save TRUE Updated commit-save TRUE FullMax(device)# show commit-save commit-save FALSE gps-card GPS card availability in the device. Command Purpose Privileges FullMax(device)#show gps-card The command allows the user display the availability of GPS card in the device. A/O Example: FullMax(device)# show gps-card gps-card YES
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 63bpc-hw-version Hardware version of baseband processor card. Command Purpose Privileges FullMax(device)#show bpc-hw-version The command allows the user display the hardware version of baseband processor card. A/O Example: FullMax(device)# show bpc-hw-version bpc-hw-version 1.10 afe-hw-ver Hardware version of the Analog Front End (AFE) Command Purpose Privileges FullMax(device)#show afe-hw-ver The command allows the user display the hardware version of AFE. A/O Example: FullMax(device)# show afe-hw-ver device-afe-hw-version 1.3 afe-sw-ver Software version of the Analog Front End (AFE) Command Purpose Privileges FullMax(device)#show afe-sw-ver The command allows the user display the software version of AFE. A/O Example: FullMax(device)# show afe-sw-ver device-afe-sw-version 1.3 build-sw-ver Software version of the device general embedded software Command Purpose Privileges FullMax(device)#show build-sw-ver The command allows the user display the software version of the software build A/O Example:
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 64FullMax(device)# show build-sw-ver build-sw-version 5.2.12 Measurements The Measurement group defines the commands that monitors or updates the measurement related information in the private MIB. The user upon entering the device command locks into the CLI to execute commands only related to Measurement. FullMax# FullMax# measurement FullMax(measurement)# Temperature Temperature degree in Celsius Command Purpose Privileges FullMax(measurement)#show temperature The command allows the user display temperature of the device. A/O FullMax(measurement)#track [-rN] [-tN] temperature The command allows the user to display real time temperature sample of the device. A/O Example: FullMax(measurement)# show temperature Temperature 45 degrees-Celsius FullMax(measurement)# track –r3 –i2 temperature Temperature 45 degrees-Celsius Temperature 46 degrees-Celsius Temperature 45 degrees-Celsius Voltage Voltage measurement Command Purpose Privileges FullMax(measurement)# show voltage The command allows the user display voltage of the device. A/O FullMax(measurement)# track [-rN] [-tN] voltage The command allows the user to display multiple voltage samples of the device. A/O Example: FullMax (measurement) # show voltage Voltage 3 volts FullMax (measurement) # track –r3 –i10 voltage
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 65 Voltage 3 volts Voltage 3 volts Voltage 3 volts Current Current measurements Command Purpose Privileges FullMax(measurement)# show current The command allows the user display the current in the device. A/O FullMax(measurement)# track [-rN] [-tN] current The command allows the user to display multiple current measurements in the device. A/O Example: FullMax (measurement) # show current Current 2 amp FullMax (measurement) # track –r4 current Current 2 amp Current 2 amp Current 2 amp Tx-power Transmit power Command Purpose Privileges FullMax(measurement)# show tx-power The command allows the user display the transmit power. A/O FullMax(measurement)# track [-rN] [-tN] tx-power The command allows the user to display multple transmit power measurements. A/O Example: FullMax (measurement) # show tx-power Tx-power 45 dBm FullMax (measurement) # track –r2 tx-power Tx-power 45 dBm Tx-power 43 dBm Rx-power Receive power Command Purpose Privileges FullMax(measurement)# The command allows the user display A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 66show rx-power the receive power. FullMax(measurement)# track [-rN] [-tN] rx-power The command allows the user to display multiple receive power measurements. A/O Example: FullMax(measurement)# show rx-power rx-power 45 dBm FullMax(measurement)# track –r2 -i2 rx-power rx-power 45 dBm rx-power 45 dBm afe-temperature Read the temperature from the Analog Front End. Command Purpose Privileges FullMax(measurement)# show afe-temperature The command allows the user display temperatue from Analog Front End. A/O FullMax(measurement)# track [-rN] [-tN] afe-temperature The command allows the user to track the temperatue from Analog Front End. A/O Example: FullMax(measurement)# show afe-temperatue afe-temperature 27 celcius FullMax(measurement)# track -r4 -i30 afe-temperatue afe-temperature 27 celcius afe-temperature 27 celcius afe-temperature 27 celcius afe-temperature 27 celcius afe-rssi Read the Receive Signal Strength Indicator (RSSI) from the Analog Front End. Command Purpose Privileges FullMax(measurement)#show afe-rssi The command allows the user display RSSI from Analog Front End. A/O FullMax(measurement)#track [-rN] [-tN] afe-rssi The command allows the user to track RSSI from Analog Front End. A/O Example: FullMax(measurement)# show afe-rssi afe-rssi 80 dBm FullMax(measurement)# track -r3 -i30 afe-rssi
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 67 afe-rssi 80 dBm afe-rssi 80 dBm afe-rssi 80 dBm 5.2.13 pkm–config pkm–config The Pkm-Config group defines the commands that moniters or updates the Private Key Management Version 2 Realated information in the Standard MIB .The user upon entering the pkm-config command locks into this group to execute commands only related to this group. FullMax# FullMax# pkm–config FullMax(pkm–config) Command Purpose Privileges FullMax# pkm –config The command allows the user to lock to pkm-config group and display the pkm –config prompt. A/O FullMax# pkm–config pkm-v2-config-table This table conatins the configuration of the pkm attributes that are needed to pkm operation. Command Purpose Privileges FullMax(pkm–config)# show pkm-v2-config-table The command allows the user display all the Pkm V2 Config table parameter values. A/O Example: FullMax(pkm–config)# show pkm-v2-config-table pmk-pre-handshake-lifetime 10 second pmk-lifetime 3600 seconds sa-tek-challenge-timeout 10000 milliseconds max-sa-tek-challenge 3 max-sa-tek-request 3
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 68pkm-pmk-pre-handshake-lifetime Defines the PkmPmkPrehandshakeLifetime. Command Purpose Privileges FullMax(pkm–config)#set pkm-pmk-pre-handshake-lifetime <val> The command allows the user update PkmPmkPrehandshakeLifetime. A/O FullMax(pkm–config)#show pkm-pmk-pre-handshake-lifetime The command allows the user to display PkmPmkPrehandshakeLifetime value A/O Example: FullMax(pkm–config)# set pkm-pmk-pre-handshake-lifetime 11 Updated pkm-pmk-pre-handshake-lifetime 11 second FullMax(pkm–config)# show pkm-pmk-pre-handshake-lifetime pmk-pre-handshake-lifetime 10 second pkm-pmk-lifetime Defines the PMK life time Command Purpose Privileges FullMax(pkm–config)#set pkm-pmk-lifetime <val> The command allows the user to update pkm-pmk-lifetime value A FullMax(pkm–config)#show pkm-pmk-lifetime The command allows the user display pkm-pmk-lifetime. A/O Example: FullMax(pkm–config) # set pkm-pmk-lifetime 3300 Updated pkm-pmk-lifetime 3300 seconds FullMax(pkm–config) # show pkm-pmk-lifetime 3600 seconds pkm-pmk-lifetime 3300 seconds sa-challenge-timeout This object defines the timeout value for SA-TEk challenge Retransmission. Command Purpose Privileges
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 69FullMax(pkm–config)#set sa-challenge-timeout <val> The command allows the user to update sa-challenge-timeout. A FullMax(pkm–config)#show sa-challenge-timeout The command allows the user display sa-challenge-timeout. A/O Example: FullMax(pkm–config) # set sa-challenge-timeout 666 updated value of sa-tek-challenge-timeout 666 millisecond FullMax(pkm–config) # show sa-challenge-timeout sa-tek-challenge-timeout 10000 milliseconds max-sa-tek-challange This object defines the maximum number of SA-TEK-Challenge Transmissions Command Purpose Privileges FullMax(pkm–config)#set max-sa-tek-challenge <val> The command allows the user to update sa-challenge-timeout. A FullMax(pkm–config)#show max-sa-tek-challange The command allows the user display max-sa-tek-challenge. A/O Example: FullMax(pkm–config)# set max-sa-tek-challange 2 updated value of max-sa-tek-challenge 2 FullMax(pkm–config)# show max-sa-tek-challange max-sa-tek-challenge 3 max-sa-tek-request This object defines the maximum number of SA-TEK -Request retransmission. Command Purpose Privileges FullMax(pkm–config)#set max-sa-tek-request <val> The command allows the user to update max-sa-tek-request. A FullMax(pkm–config)#show max-sa-tek-request The command allows the user to display max-sa-tek-request. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 70 Example: FullMax(pkm–config)# set max-sa-tek-request 2 updated value of max-sa-tek-request 2 FullMax(pkm–config)# show max-sa-tek-request max-sa-tek-request 3 all The command allows the user to display all the parameters of the tables in this group. Command Purpose Privileges FullMax(pkm–config)#show all The command allows the user to display all the parameters values of the in this group. A/O FullMax(pkm–config) # show all pmk-pre-handshake-lifetime 10 second pmk-lifetime 3600 seconds sa-tek-challenge-timeout 10000 milliseconds max-sa-tek-challenge 3 max-sa-tek-request 3 5.2.14 bs-private FullMax# FullMax# bs-private FullMax(bs-private)# Command Purpose Privileges FullMax#bs-private The command allows the user to lock to bs-private group and display the bs-private prompt. A/O bs-rx-amc-count-table This table contains statistical information that can be used to characterize the adaptive modulation and coding performance in the uplink. Command Purpose Privileges FullMax(bs-private)# show bs-rx-amc-count-table <uiuc-index> This command shows all the parameters and their values for AmcCountTable A/O Example: FullMax(bs-private)# show bs-rx-amc-count-table 1 bs-rx-octets for uiuc index 1 is 0
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 71 bs-rx-packets for uiuc index 1 is 0 bs-tx-erroredpackets for uiuc index 1 is 0 bs-rx-uiuc-index The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message, and is used along with ifIndex to identify an entry in the wmanIf2BsOfdmaUcdBurstProfileTable. Command Purpose Privileges FullMax(bs-private)#show bs-rx-uiuc-index Show all the Uplink Interval Usage Code index available.A/O A/O Example: FullMax(bs-private)# show bs-rx-uiuc-index uiuc indices are bs-ul-uiuc-index: 1 bs-ul-uiuc-index: 2 bs-ul-uiuc-index: 3 bs-ul-uiuc-index: 4 bs-ul-uiuc-index: 5 bs-ul-uiuc-index: 6 bs-ul-uiuc-index: 7 bs-ul-uiuc-index: 8 bs-ul-uiuc-index: 9 bs-ul-uiuc-index: 10 bs-rx-octets This object counts the number of octets received in the uplink using the uplink burst profile indexed by wmanPriBsRxUiucIndex. Command Purpose Privileges FullMax(bs-private)#show bs-rx-octets <uiuc-index> Show the no of octet received in the uplink for the given index A/O Example: FullMax(bs-private)# show bs-rx-octets 1 bs-rx-octets for uiuc index 1 is 0 bs-rx-packets This object counts the number of packets received in the uplinkusing the uplink burst profile indexed by UiucIndex Command Purpose Privileges FullMax(bs-private)#show bs-Shows the number of packets received in the uplink for the A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 72rx-packets <uiuc-index> given index Example: FullMax(bs-private)# show bs-rx-packets 1 bs-rx-packets for uiuc index 1 is 0 bs-rx-erroredPackets This object counts the number of errored packets received in the uplink using the uplink burst profile indexed by UiucIndex. Command Purpose Privileges FullMax(bs-private)#show bs-rx-erroredPackets <uiuc-index> Shows the number of errored packets received in the uplink for the given index A/O Example: FullMax(bs-private)# show bs-rx-erroredPackets 1 bs-tx-errored packets for uiuc index 1 is 0 bs-tx-amc-count-table This table contains statistical information that can be used to characterize the adaptive modulation and coding performance in the downlink. Command Purpose Privileges FullMax(bs-private)#show bs-tx-amc-count-table <diuc-index> Show all the parameters and their values of the TxAmcCountTable table for the given index A/O Example: FullMax(bs-private)# show bs-tx-amc-count-table 1 bs-tx-octets for diuc index 1 is 0 bs-tx-packets for diuc index 1 is 0 bsbsbsbs----txtxtxtx----diucdiucdiucdiuc----indexindexindexindex The Downlink Interval Usage Code indicates the downlink burst profile in the DCD message. Command Purpose Privileges FullMax(bs-private)#show bs-tx-diuc-index Show all the available Downlink Interval Usage indices. A/O Example: FullMax(bs-private)# show bs-tx-diuc-index diuc indices are
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 73 bs-dl-diuc-index: 0 bs-dl-diuc-index: 1 bs-dl-diuc-index: 2 bs-dl-diuc-index: 3 bs-dl-diuc-index: 4 bs-dl-diuc-index: 5 bs-dl-diuc-index: 6 bs-dl-diuc-index: 7 bs-dl-diuc-index: 8 bs-dl-diuc-index: 9 bs-dl-diuc-index: 10 bs-dl-diuc-index: 11 bs-dl-diuc-index: 12 bs-tx-octets This object counts the number of octets transmitted in the downlink using the downlink burst profile indexed by DiucIndex. Command Purpose Privileges FullMax(bs-private)# show bs-tx-octets <diuc-index> Shows the number of octets transmitted in the downlink for the given index A/O Example: FullMax(bs-private)# show bs-tx-octets 1 bs-tx-octets for diuc index 1 is 0 bs-tx-packets This object counts the number of packets transmitted in the downlink using the downlink burst profile indexed by Diuc Index. Command Purpose Privileges FullMax(bs-rivate)#show bs-tx-packets <diuc-index> Shows the number of packets transmitted in the downlink for the given index A/O Example: FullMax(bs-private)# show bs-tx-packets 1 bs-tx-packets for diuc index 1 is 0 cmn-sf-table This Table measures service flow traffic . Command Purpose Privileges FullMax(bs-private)#show cmn-sf-table <sfid> This command show all the parameters and their values of Cmn-A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 74sf-table. Example: FullMax(bs-private)# show cmn-sf-table 2001 sf-total-octets for sfid 2001 is 100 sf-total-pkts for sfid 2001 is 2 sf-errored-pkts for sfid 2001 is 1 sf-frag-orig for sfid 2001 is 1 sf-frag-total for sfid 2001 is 2 sf-missing-frag for sfid 2001 is 0 cmn-pm-sfid This is a 32 bit quantity that uniquely identifies a service flow to both the subscriber station and base station. Command Purpose Privileges FullMax(bs-private)#show cmn-pm-sfid <mac-ddress> This command shows all the avaliable Service Flow Id's Avaliable for a particular MSID. A/O Example : FullMax(bs-private)# show cmn-pm-sfid 112233:445566 cmn-pm-sfid 2001 cmn-pm-sfid 2002 cmn-pm-sfid 2003 cmn-pm-sfid 2006 sf-total-octets This determines the total octets received/transmitted on this service flow. Command Purpose Privileges FullMax(bs-private)# show sf-total-octets <sfid> This command allows the user to diplay the total octets received or transmitted for this service-flow. A/O Example: FullMax(bs-private)#show sf-total-octets 2001 sf-total-octets for sfid (2001) : 1000 sf-total-pkts This determines the total number of packets received /transmitted on this service flow. Command Purpose Privileges FullMax(bs-private)#show sf-total-pkts <sfid> This Command allows the user to display the total packets received or trasmitted for this service-flow A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 75 Example: FullMax(bs-private)#show sf-total-pkts 2001 sf-total-pkts for sfid (2001): 22 sf-errored-pkts This determines number of packets that were dropped due to missing fragments / bad ARQ blocks. Command Purpose Privileges FullMax(bs-private)#show sf-errored-pkts <sfid> This Command Allows the user to display the total errored packets received or transmitted for this service flow. A/O Example: FullMax(bs-private)# show sf-errored-pkts 2001 sf-errored-pkts for sfid (2001): 1 sfsfsfsf----fragfragfragfrag----origorigorigorig This determines number of fragments / ARQ blocks originally transmitted/received on this service flow. Command Purpose Privileges FullMax(bs-private)#show sf-frag-orig <sfid> This Command allows the user to display the total fragments received or transmitted originally on this service flow. A/O Example: FullMax(bs-private)#show sf-frag-orig 2001 sf-frag-orig for sfid (2001) : 2 sfsfsfsf----fragfragfragfrag----totaltotaltotaltotal This determines total fragments / ARQ blocks transmitted / received on this service flow. Command Purpose Privileges FullMax(bs-private)#show sf-frag-total <sfid> This Command allows the user to display the total fragments received or transmitted on this service flow. A/O Example: FullMax(bs-private)# show sf-frag-total 2001
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 76 sf-frag-total for sfid (2001): 2 sfsfsfsf----missingmissingmissingmissing----fragfragfragfrag Description This determines the number of missing received fragments received or NACK. Command Purpose Privileges FullMax(bs-private)# show sf-missing-frag <sfid> This command allows the user to display the number of missing received fragments or NACK. A/O Example: FullMax(bs-private)# show sf-missing-frag 2001 sf-missing-frag for sfid (2001): 1 5.2.15 trap-config traptraptraptrap----configconfigconfigconfig This Command allows the user to lock to trap config group. Command Purpose Privileges FullMax # trap-config This command allows the user to Locks to the trap config group and displays the coresponding group prompt. A/O Example: FullMax # trap-config FullMax(trap-config) # stdstdstdstd----traptraptraptrap----ctrlctrlctrlctrl The object is used to enable or disable Base Station traps From left to right, the set bit indicates the corresponding Base Station trap is enabled {wmanIf2BsSsStatusNotification (0), wmanIf2BsSsDynamicServiceFail (1), wmanIf2BsSsRssiStatusChange (2), wmanIf2BsSsRegister (3), wmanIf2BsSsPkmFail (4), wmanIf2BsPerformanceCounters (5)} Command Purpose Privileges FullMax(trap-config) # set std-trap-ctrl This command Allows the user to update the value of std-trap-ctrl parameter. A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 77<val> FullMax(trap-config) # show std-trap-ctrl This command Allows the user to display the value of std-trap-ctrl parameter. A/O Example: FullMax(trap-config) # set std-trap-ctrl 25 updated bs-trap-control {wmanIf2BsSsStatusNotification(0), wmanIf2BsSsRegister(3), wmanIf2BsPerformanceCounters (4) } FullMax(bs-private)# show std-trap-ctrl bs-trap-control enabled are { wmanIf2BsSsStatusNotification(0), wmanIf2BsSsRegister(3), wmanIf2BsPerformanceCounters (4) } stdstdstdstd----traptraptraptrap----statusstatusstatusstatus----ctrlctrlctrlctrl The object is used to enable or disable Base Station status notification traps. The set bit indicates the corresponding Base Station trap is enabled. { unused(0), ssInitRangingSucc(1), ssInitRangingFail(2), ssRegistered(3), ssRegistrationFail(4), ssDeregistered(5), ssBasicCapabilitySucc(6), ssBasicCapabilityFail(7), ssAuthorizationSucc(8), ssAuthorizationFail(9), tftpSucc(10), tftpFail(11), sfCreationSucc(12), sfCreationFail(13) } Command Purpose Privileges FullMax(trap-config) # set std-trap-status-ctrl <val> This command Allows the user to update the value of std-trap-status-ctrl parameter. A FullMax(trap-config) # show std-trap-status-ctrl This command Allows the user to display the value of std-trap-status-ctrl parameter. A/O FullMax(bs-private)# set std-trap-status-ctrl 10900 updated bs-trap-status-ctrl {ssInitRangingFail(2), ssRegistrationFail(4), ssBasicCapabilityFail(7),ssAuthorizationFail(9), tftpFail(11), sfCreationFail(13) }
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 78 FullMax(bs-private)# show std-trap-status-ctrl bs-trap-status-ctrl enabled are {ssInitRangingFail(2), ssRegistrationFail(4), ssBasicCapabilityFail(7),ssAuthorizationFail(9), tftpFail(11), sfCreationFail(13) } privateprivateprivateprivate----traptraptraptrap----ctrlctrlctrlctrl The object is used to enable or disable Base Station traps From left to right, the set bit indicates the corresponding Base Station trap is enabled. { wmanPriPowerStatusChange (0), wmanPriFanStatusChange (1), wmanPriTemperatureChange (2), wmanPriConfigChange (3), wmanPriAfeBitError (4) } Command Purpose Privileges FullMax(trap-config) # set private-trap-ctrl <val> This command Allows the user to update the value of private-trap-ctrl parameter. A FullMax(trap-config) # show private-trap-ctrl This command Allows the user to display the value of private-trap-ctrl parameter. A/O FullMax(bs-private)# set private-trap-ctrl 21 updated private-trap-ctrl { wmanPriPowerStatusChange(0), wmanPriPowerStatusChange(2), wmanPriPowerStatusChange (4)} FullMax(bs-private)# show private-trap-ctrl private-trap-ctl enabled { wmanPriPowerStatusChange(0), wmanPriPowerStatusChange(2), wmanPriPowerStatusChange (4)} 5.2.16 lapc-config LapcLapcLapcLapc----configconfigconfigconfig This group contains commands to manipulate the Link Adaption and Power Control configuration parameters for the Base Station MAC. Command Purpose
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 79FullMax#lapc-config The command allows the user to lock to config group and display the config prompt. FULLMAX#lapc-config FULLMAX(lapc-config)]# uiucuiucuiucuiuc Command Purpose FullMax(lapc-config)# show uiuc Shows the values of uiuc avaliable. Example: FULLMAX(lapc-config)#show uiuc uiuc 1 uiuc 2 Uplink_FEC_Code_TypeUplink_FEC_Code_TypeUplink_FEC_Code_TypeUplink_FEC_Code_Type Command Purpose FullMax(lapc-config)# set Uplink_FEC_Code_Type <uiuc index> value The command sets the value of Uplink_FEC_Code_Type for the given index FullMax(lapc-config)# show Uplink_FEC_Code_Type <uiuc index> The command show the value of Uplink_FEC_Code_Type for the particunlar uiuc index Example: FULLMAX(lapc-config)#set Uplink_FEC_Code_Type 1 333 Updated Uplink_FEC_Code_Type for uiuc index 1 is 333 FULLMAX(lapc-config)#show Uplink_FEC_Code_Type 1 Uplink_FEC_Code_Type for uiuc index 1 is 0 Ranging_Data_RatioRanging_Data_RatioRanging_Data_RatioRanging_Data_Ratio Command Purpose FullMax(lapc-config)# set Ranging_Data_Ratio <uiuc index> The command sets the value of Ranging_Data_Ratio for the given index. FullMax(lapc-config)# show Ranging_Data_Ratio <uiuc index> The command shows the value of Ranging_Data_Ratio for the given index. Example:
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 80 FULLMAX(lapc-config)#set Ranging_Data_Ratio 1 22 Updated Ranging_Data_Ratio for uiuc index 1 is 22 FULLMAX(lapc-config)#show Ranging_Data_Ratio 1 Ranging_Data_Ratio for uiuc index 1 is 19 Normalised_C_by_N_MantissaNormalised_C_by_N_MantissaNormalised_C_by_N_MantissaNormalised_C_by_N_Mantissa Command Purpose FullMax(lapc-config)# set Normalised_C_by_N_Mantissa <uiuc index> The commnad sets the value of Normalised_C_by_N_Mantissa for the given index FullMax(lapc-config)# show Normalised_C_by_N_Mantissa <uiuc index> The commnad shows the value of Normalised_C_by_N_Mantissa for the given index Example: FULLMAX(lapc-config)#set Normalised_C_by_N_Mantissa 1 77 Updated Normalised_C_by_N_Mantissa for uiuc index 1 is 77 FULLMAX(lapc-config)#show Normalised_C_by_N_Mantissa 1 Normalised_C_by_N_Mantissa for uiuc index 1 is 60 Normalised_C_by_N_ExponentNormalised_C_by_N_ExponentNormalised_C_by_N_ExponentNormalised_C_by_N_Exponent Command Purpose FullMax(lapc-config)# set Normalised_C_by_N_Exponent <uiuc index> The command sets the value of Normalised_C_by_N_Exponent for the given index FullMax(lapc-config)# show Normalised_C_by_N_Exponent <uiuc index> The command shows the value of Normalised_C_by_N_Exponent for the given index Example: FULLMAX(lapc-config)#set Normalised_C_by_N_Exponent 1 1 Updated Normalised_C_by_N_Exponent for index 1 is 1 FULLMAX(lapc-config)#show Normalised_C_by_N_Exponent 1 Normalised_C_by_N_Exponent for index 1 is -1 FIR_filter_coefficient_mantissaFIR_filter_coefficient_mantissaFIR_filter_coefficient_mantissaFIR_filter_coefficient_mantissa
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 81Command Purpose FullMax(lapc-config)# set FIR_filter_coefficient_mantissa <index> value The command sets the value of FIR_filter_coefficient_mantissa for the given index FullMax(lapc-config)# show FIR_filter_coefficient_mantissa <index> The command shows the value of FIR_filter_coefficient_mantissa for the given index Example: FULLMAX(lapc-config)#set FIR_filter_coefficient_mantissa 1 65 Updated FIR_filter_coefficient_mantissa for index 1 is 65 FULLMAX(lapc-config)#show FIR_filter_coefficient_mantissa 1 FIR_filter_coefficient_mantissa for index 1 is 65 FIR_filter_coefficient_TenPwrFIR_filter_coefficient_TenPwrFIR_filter_coefficient_TenPwrFIR_filter_coefficient_TenPwr Command Purpose FullMax(lapc-config)#set FIR_filter_coefficient_TenPwr <index> <val> The command sets the value of FIR_filter_coefficient_TenPwr for the given index. FullMax(lapc-config)#show FIR_filter_coefficient_TenPwr <index> The command shows the value of FIR_filter_coefficient_TenPwr for the given index. Example: FULLMAX(lapc-config)#set FIR_filter_coefficient_TenPwr 1 3 Updated FIR_filter_coefficient_TenPwr for index 1 is 3 FULLMAX(lapc-config)#show FIR_filter_coefficient_TenPwr 1 FIR_filter_coefficient_TenPwr for index 1 is 3 Dl_Benchmark_Entry_Threshold_CINRDl_Benchmark_Entry_Threshold_CINRDl_Benchmark_Entry_Threshold_CINRDl_Benchmark_Entry_Threshold_CINR Description Command Purpose FullMax(lapc-config)#set Dl_Benchmark_Entry_Threshold_CINR <dl_fec_code> <dl_repetition> <val> Sets the value of Dl_Benchmark_Entry_Threshold_CINR for the given fec code and repetition . FullMax(lapc-config)#show Dl_Benchmark_Entry_Threshold_CDisplays the value of Dl_Benchmark_Entry_Threshold_CINR for the
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 82INR <dl_fec_code> <dl_repetition> given fec code and repetition . Example: FULLMAX(lapc-config)#set Dl_Benchmark_Entry_Threshold_CINR 4 2 41e3 Updated Dl_Benchmark_Entry_Threshold_CINR for fec code 4 and repition 2 is 41e3 FULLMAX(lapc-config)#show Dl_Benchmark_Entry_Threshold_CINR 4 2 Dl_Benchmark_Entry_Threshold_CINR for fec code 4 and repition 2 is 19e1 Dl_Benchmark_Exit_Threshold_CINRDl_Benchmark_Exit_Threshold_CINRDl_Benchmark_Exit_Threshold_CINRDl_Benchmark_Exit_Threshold_CINR Description Command Purpose FullMax(lapc-config)#set Dl_Benchmark_Exit_Threshold_CINR <dl_fec_code> <dl_repetition> <val> Sets the value of Dl_Benchmark_Exit_Threshold_CINR for the given fec code and repetition . FullMax(lapc-config)#show Dl_Benchmark_Exit_Threshold_CINR <dl_fec_code> <dl_repetition> Displays the value of Dl_Benchmark_Exit_Threshold_CINR for the given fec code and repetition . Example: FULLMAX(lapc-config)#set Dl_Benchmark_Exit_Threshold_CINR 4 2 41e3 Updated Dl_Benchmark_Exit_Threshold_CINR for fec code 4 and repition 2 is 41e3 FULLMAX(lapc-config)#show Dl_Benchmark_Exit_Threshold_CINR 4 2 Dl_Benchmark_Exit_Threshold_CINR for fec code 4 and repition 2 is 19e1 Ul_Benchmark_Entry_Threshold_CINRUl_Benchmark_Entry_Threshold_CINRUl_Benchmark_Entry_Threshold_CINRUl_Benchmark_Entry_Threshold_CINR Command Purpose FullMax(lapc-config)#set Ul_Benchmark_Entry_Threshold_CSets the value of Ul_Benchmark_Entry_Threshold_CINR for the
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 83INR <dl_fec_code> <dl_repetition> <val> given fec code and repetition . FullMax(lapc-config)#show Ul_Benchmark_Entry_Threshold_CINR <dl_fec_code> <dl_repetition> Displays the value of Ul_Benchmark_Entry_Threshold_CINR for the given fec code and repetition . FULLMAX(lapc-config)#set Ul_Benchmark_Entry_Threshold_CINR 4 2 41e3 Updated Ul_Benchmark_Entry_Threshold_CINR for fec code 4 and repition 2 is 41e3 FULLMAX(lapc-config)#show Ul_Benchmark_Entry_Threshold_CINR 4 2 Ul_Benchmark_Entry_Threshold_CINR for fec code 4 and repition 2 is 19e1 Ul_Benchmark_Exit_Threshold_CINRUl_Benchmark_Exit_Threshold_CINRUl_Benchmark_Exit_Threshold_CINRUl_Benchmark_Exit_Threshold_CINR Description Command Purpose FullMax(lapc-config)#set Ul_Benchmark_Exit_Threshold_CINR <ul_fec_code> <ul_repetition> <val> Sets the value of Ul_Benchmark_Exit_Threshold_CINR for the given fec code and repetition . FullMax(lapc-config)#show Ul_Benchmark_Exit_Threshold_CINR <ul_fec_code> <ul_repetition> Displays the value of Ul_Benchmark_Exit_Threshold_CINR for the given fec code and repetition . Example: FULLMAX(lapc-config)#set Dl_Benchmark_Exit_Threshold_CINR 4 2 41e3 Updated Dl_Benchmark_Exit_Threshold_CINR for fec code 4 and repition 2 is 41e3 FULLMAX(lapc-config)#show Dl_Benchmark_Exit_Threshold_CINR 4 2 Dl_Benchmark_Exit_Threshold_CINR for fec code 4 and repition 2 is 19e1 Burst_Profile_evaluation_TimerBurst_Profile_evaluation_TimerBurst_Profile_evaluation_TimerBurst_Profile_evaluation_Timer Command Purpose
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 84FullMax(lapc-config)#set Burst_Profile_evaluation_Timer The command sets the value of _Profile_evaluation_Timer FullMax(lapc-config)#show Burst_Profile_evaluation_Timer The command shows the value of _Profile_evaluation_Timer Example: FULLMAX(lapc-config)#set Burst_Profile_evaluation_Timer 222 Updated Burst_Profile_evaluation_Timer: 250 FULLMAX(lapc-config)#show Burst_Profile_evaluation_Timer Burst_Profile_evaluation_Timer: 250 Mantissa_Lower_Thld_Rx_Power_DensityMantissa_Lower_Thld_Rx_Power_DensityMantissa_Lower_Thld_Rx_Power_DensityMantissa_Lower_Thld_Rx_Power_Density Description Command Purpose FullMax(lapc-config)# set Mantissa_Lower_Thld_Rx_Power_Density <val> Sets the value of Mantissa_Lower_Thld_Rx_Power_Density FullMax(lapc-config)# show Mantissa_Lower_Thld_Rx_Power_Density Displays the value of Mantissa_Lower_Thld_Rx_Power_Density. Example: FULLMAX(lapc-config)#set Mantissa_Lower_Thld_Rx_Power_Density 22 Updated Mantissa_Lower_Thld_Rx_Power_Density -100 FULLMAX(lapc-config)#show Mantissa_Lower_Thld_Rx_Power_Density Mantissa_Lower_Thld_Rx_Power_Density -100 Mantissa_Higher_Thld_Rx_Power_DensityMantissa_Higher_Thld_Rx_Power_DensityMantissa_Higher_Thld_Rx_Power_DensityMantissa_Higher_Thld_Rx_Power_Density Description Command Purpose FullMax(lapc-config)#set Mantissa_Higher_Thld_Rx_Power_Density Sets the value of Mantissa_Higher_Thld_Rx_Power_Density to the given value. FullMax(lapc-config)#show Mantissa_Higher_Thld_Rx_Power_Density Display the value of Mantissa_Higher_Thld_Rx_Power_Density Example:
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 85FULLMAX(lapc-config)#set Mantissa_Higher_Thld_Rx_Power_Density 22 Updated Mantissa_Higher_Thld_Rx_Power_Density 22 FULLMAX(lapc-config)#show Mantissa_Higher_Thld_Rx_Power_Density Mantissa_Higher_Thld_Rx_Power_Density -60 Max_Length_Of_DLMAP_MesgMax_Length_Of_DLMAP_MesgMax_Length_Of_DLMAP_MesgMax_Length_Of_DLMAP_Mesg Command Purpose FullMax(lapc-config)#set Max_Length_Of_DLMAP_Mesg <value> The command sets the value of _Length_Of_DLMAP_Mesg to the value given FullMax(lapc-config)#show Max_Length_Of_DLMAP_Mesg The command shows the value of _Length_Of_DLMAP_Mesg Example: FULLMAX(lapc-config)#set Max_Length_Of_DLMAP_Mesg 22 Updated Max_Length_Of_DLMAP_Mesg: 22 FULLMAX(lapc-config)#show Max_Length_Of_DLMAP_Mesg Max_Length_Of_DLMAP_Mesg: 2 Max_Aggregate_Length_Of_Control_Messages Command Purpose FullMax(lapc-config)# set Max_Aggregate_Length_Of_Control_Messages <value> The command sets the value of _Aggregate_Length_Of_Control_Messages to the given value. FullMax(lapc-config)# show Max_Aggregate_Length_Of_Control_Messages The command shows the value of _Aggregate_Length_Of_Control_Messages. Example: FULLMAX(lapc-config)#set Max_Aggregate_Length_Of_Control_Messages 22 Updated Max_Aggregate_Length_Of_Control_Messages: 22 FULLMAX(lapc-config)#show Max_Aggregate_Length_Of_Control_Messages Max_Length_Of_DLMAP_Mesg: 48 Max_No_Of_Slots_Used_For_Future_Allocation_In_DLMax_No_Of_Slots_Used_For_Future_Allocation_In_DLMax_No_Of_Slots_Used_For_Future_Allocation_In_DLMax_No_Of_Slots_Used_For_Future_Allocation_In_DL
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 86Command Purpose FullMax(lapc-config)# set Max_No_Of_Slots_Used_For_Future_Allocation_In_DL <value> The command sets the value of _No_Of_Slots_Used_For_Future_Allocation_In_DL to the given value. FullMax(lapc-config)# show Max_No_Of_Slots_Used_For_Future_Allocation_In_DL The command shows the value of _No_Of_Slots_Used_For_Future_Allocation_In_DL. Example: [FULLMAX(lapc-config)]$set Max_No_Of_Slots_Used_For_Future_Allocation_In_DL 33 Updated Max_No_Of_Slots_Used_For_Future_Allocation_In_DL: 33 [FULLMAX(lapc-config)]$show Max_No_Of_Slots_Used_For_Future_Allocation_In_DL Max_Aggregate_Length_Of_Control_Messages: 90 Max_No_Of_Slots_Used_For_Future_Allocation_In_ULMax_No_Of_Slots_Used_For_Future_Allocation_In_ULMax_No_Of_Slots_Used_For_Future_Allocation_In_ULMax_No_Of_Slots_Used_For_Future_Allocation_In_UL Command Purpose FullMax(lapc-config)# set Max_No_Of_Slots_Used_For_Future_Allocation_In_UL <value> The command sets the value of _No_Of_Slots_Used_For_Future_Allocation_In_UL to the given value. FullMax(lapc-config)# show Max_No_Of_Slots_Used_For_Future_Allocation_In_UL The command shows the value of _No_Of_Slots_Used_For_Future_Allocation_In_UL. Example: FULLMAX(lapc-config)#set Max_No_Of_Slots_Used_For_Future_Allocation_In_UL 44 Updated Max_No_Of_Slots_Used_For_Future_Allocation_In_DL: 44 FULLMAX(lapc-config)#show Max_No_Of_Slots_Used_For_Future_Allocation_In_UL Max_No_Of_Slots_Used_For_Future_Allocation_In_DL: 10
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 87Command Purpose FullMax(lapc-config)#set Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame <value> The command sets the value of _No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame to the given value. FullMax(lapc-config)#show Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame The command shows the value of _No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame. Example: FULLMAX(lapc-config)#set Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame 22 Updated Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame: 22 FULLMAX(lapc-config)#show Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame Max_No_Of_Slots_Used_For_Future_Allocation_In_DL: 10 No_Of_CDMA_Ranging_SlotsNo_Of_CDMA_Ranging_SlotsNo_Of_CDMA_Ranging_SlotsNo_Of_CDMA_Ranging_Slots Command Purpose FullMax(lapc-config)# set No_Of_CDMA_Ranging_Slots <value> The command sets the value of _Of_CDMA_Ranging_Slots to the given value. FullMax(lapc-config)# show No_Of_CDMA_Ranging_Slots The command shows the value of _Of_CDMA_Ranging_Slots. FULLMAX(lapc-config)#set No_Of_CDMA_Ranging_Slots 33 Updated No_Of_CDMA_Ranging_Slots: 33 FULLMAX(lapc-config)#show No_Of_CDMA_Ranging_Slots No_Of_CDMA_Ranging_Slots: 1 CDMA_Ranging_PeriodCDMA_Ranging_PeriodCDMA_Ranging_PeriodCDMA_Ranging_Period Command Purpose FullMax(lapc-config)# set CDMA_Band_Width_Period <value> The command sets the value of CDMA_Band_Width_Period to the given value. FullMax(lapc-config)# show The command shows the value of
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 88CDMA_Band_Width_Period CDMA_Band_Width_Period FULLMAX(lapc-config)#set CDMA_Band_Width_Period 33 Updated CDMA_Band_Width_Period: 33 FULLMAX(lapc-config)#show CDMA_Band_Width_Period CDMA_Band_Width_Period: 6 No_Of_CDMA_Band_Width_SlotsNo_Of_CDMA_Band_Width_SlotsNo_Of_CDMA_Band_Width_SlotsNo_Of_CDMA_Band_Width_Slots Command Purpose FullMax(lapc-config)# set No_Of_CDMA_Band_Width_Slots <value> The command sets the value of _Of_CDMA_Band_Width_Slots to the given value FullMax(lapc-config)# show No_Of_CDMA_Band_Width_Slots The command shows the value of _Of_CDMA_Band_Width_Slots Example: FULLMAX(lapc-config)#set No_Of_CDMA_Band_Width_Slots 33 Updated No_Of_CDMA_Band_Width_Slots: 33 FULLMAX(lapc-config)#show No_Of_CDMA_Band_Width_Slots No_Of_CDMA_Band_Width_Slots: 3 CDMA_Band_Width_PeriodCDMA_Band_Width_PeriodCDMA_Band_Width_PeriodCDMA_Band_Width_Period Command Purpose FullMax(lapc-config)# set CDMA_Band_Width_Period <value> The command sets the value of _Band_Width_Period to the given value. FullMax(lapc-config)# show CDMA_Band_Width_Period The command shows the value of _Band_Width_Period. Example: FULLMAX(lapc-config)#set CDMA_Band_Width_Period 33 Updated CDMA_Band_Width_Period: 33 FULLMAX(lapc-config)#show CDMA_Band_Width_Period CDMA_Band_Width_Period: 6 Max_Frame_Slots_Dl_Harq_RetransmissionMax_Frame_Slots_Dl_Harq_RetransmissionMax_Frame_Slots_Dl_Harq_RetransmissionMax_Frame_Slots_Dl_Harq_Retransmission Command Purpose FullMax(lapc-config)# set Max_Frame_Slots_Dl_Harq_Retransmission <value> The command sets the value of _Frame_Slots_Dl_Harq_Retransmission to the given value.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 89FullMax(lapc-config)# show Max_Frame_Slots_Dl_Harq_Retransmission The command shows the value of _Frame_Slots_Dl_Harq_Retransmission. Example: FULLMAX(lapc-config)#set Max_Frame_Slots_Dl_Harq_Retransmission 33 Updated Max_Frame_Slots_Dl_Harq_Retransmission 33 FULLMAX(lapc-config)#show Max_Frame_Slots_Dl_Harq_Retransmission Max_Frame_Slots_Dl_Harq_Retransmission: 20 Max_Frame_Slots_Ul_Harq_RetransmissionMax_Frame_Slots_Ul_Harq_RetransmissionMax_Frame_Slots_Ul_Harq_RetransmissionMax_Frame_Slots_Ul_Harq_Retransmission Command Purpose FullMax(lapc-config)# set Max_Frame_Slots_Ul_Harq_Retransmission <value> The command sets the value of Max_Frame_Slots_Ul_Harq_Retransmission to the given value. FullMax(lapc-config)# show Max_Frame_Slots_Ul_Harq_Retransmission The command shows the value of _Frame_Slots_Ul_Harq_Retransmission. Example: FULLMAX(lapc-config)#set Max_Frame_Slots_Ul_Harq_Retransmission 33 Update Max_Frame_Slots_Ul_Harq_Retransmission: 33 FULLMAX(lapc-config)#show Max_Frame_Slots_Ul_Harq_Retransmission Max_Frame_Slots_Ul_Harq_Retransmission: 20 Max_Ul_Harq_Ack_slotsMax_Ul_Harq_Ack_slotsMax_Ul_Harq_Ack_slotsMax_Ul_Harq_Ack_slots Command Purpose FullMax(lapc-config)# set Max_Ul_Harq_Ack_slots <value> The command sets the value of Max_Ul_Harq_Ack_slots to the givan value. FullMax(lapc-config)# show Max_Ul_Harq_Ack_slots The command shows the value of Max_Ul_Harq_Ack_slots Example: FULLMAX(lapc-config)#set Max_Ul_Harq_Ack_slots 24 Updated Max_Ul_Harq_Ack_slots: 24 FULLMAX(lapc-config)#show Max_Ul_Harq_Ack_slots
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 90Max_Ul_Harq_Ack_slots: 2 Initial_Ranging_Backoff_StartInitial_Ranging_Backoff_StartInitial_Ranging_Backoff_StartInitial_Ranging_Backoff_Start Command Purpose FullMax(lapc-config)# set Initial_Ranging_Backoff_Start <value> The command sets the value of _Ranging_Backoff_Start to the given value. FullMax(lapc-config)# show Initial_Ranging_Backoff_Start The command shows the value of _Ranging_Backoff_Start Example: FULLMAX(lapc-config)#set Initial_Ranging_Backoff_Start 55 Updated Initial_Ranging_Backoff_Start: 55 FULLMAX(lapc-config)#show Initial_Ranging_Backoff_Start Initial_Ranging_Backoff_Start: 15 Initial_Ranging_Backoff_End Command Purpose FullMax(lapc-config)# set Initial_Ranging_Backoff_End <value> The command sets the value of _Ranging_Backoff_End to the given value. FullMax(lapc-config)# show Initial_Ranging_Backoff_End The command shows the value of _Ranging_Backoff_End. FULLMAX(lapc-config)#set Initial_Ranging_Backoff_End 44 Updated Initial_Ranging_Backoff_End: 44 FULLMAX(lapc-config)#show Initial_Ranging_Backoff_End Initial_Ranging_Backoff_End: 12 Bandwidth_Request_Backoff_Start Command Purpose FullMax(lapc-config)# set Bandwidth_Request_Backoff_Start <value> The command sets the value of _Request_Backoff_Start to the given value. FullMax(lapc-config)# show Bandwidth_Request_Backoff_Start The command shows the value of _Request_Backoff_Start. Example:
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 91FULLMAX(lapc-config)#set Bandwidth_Request_Backoff_Start 44 Updated Bandwidth_Request_Backoff_Start: 44 FULLMAX(lapc-config)#show Bandwidth_Request_Backoff_Start Bandwidth_Request_Backoff_Start: 3 Bandwidth_Request_Backoff_End Command Purpose FullMax(lapc-config)# set Bandwidth_Request_Backoff_End <value> The command sets the value of _Request_Backoff_End to the given value. FullMax(lapc-config)# show Bandwidth_Request_Backoff_End The command shows the value of _Request_Backoff_End. Example: FULLMAX(lapc-config)#set Bandwidth_Request_Backoff_End 55 Updated Bandwidth_Request_Backoff_End: 55 FULLMAX(lapc-config)#show Bandwidth_Request_Backoff_End Bandwidth_Request_Backoff_End: 2 Percentage_Of_Reserved_Symbols Command Purpose FullMax(lapc-config)# set Percentage_Of_Reserved_Symbols <value> The command sets the value of _Of_Reserved_Symbols to the given value. FullMax(lapc-config)# show Percentage_Of_Reserved_Symbols The command shows the value of _Of_Reserved_Symbols. Example: FULLMAX(lapc-config)#set Percentage_Of_Reserved_Symbols 99 Updated Percentage_Of_Reserved_Symbols: 99 FULLMAX(lapc-config)#show Percentage_Of_Reserved_Symbols Percentage_Of_Reserved_Symbols: 10 Percentags_Of_Head_Room_For_MAC Command Purpose FullMax(lapc-config)# set Percentags_Of_Head_Room_For_MAC <value> The command sets the value of _Of_Head_Room_For_MAC to the given value.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 92FullMax(lapc-config)# show Percentags_Of_Head_Room_For_MAC The command shows the value of _Of_Head_Room_For_MAC. Example: FULLMAX(lapc-config)#set Percentags_Of_Head_Room_For_MAC 88 Updated Percentags_Of_Head_Room_For_MAC: 88 FULLMAX(lapc-config)#show Percentags_Of_Head_Room_For_MAC Percentags_Of_Head_Room_For_MAC: 10 5.3 MS400 Operation The FullMax MS CLI supports the following commands. The access to this commands are based on the user privileges. The Admin has the privilege to control and monitor all the information supported by the FullMax MS CLI commands, where as the operator has limited privileges. After the successful authentication, the user gets the access permission to the command line interface. Based on the user privileges, the help menu will be displayed to the user. 5.3.1 Main Group When user logs in to the CLI it will lock to the default group which is the main group.When ever the user enters the Main group,CLI will display the main prompt .Help command in main group will show the commands supported in main group along with the group lock commands. Only commands related to main group can be executed in main group. FullMax# main group ipipipip----addressaddressaddressaddress System IP address. Command Purpose Privileges FullMax# set ip-address <ip-address> Updates the system IP address. A/O FullMax# show ip-address Displays the system IP address. A/O Example: FullMax#set ip-address 10.60.4.42 Updated IP address: 10.60.4.42 FullMax# show ip-address IP address: 10.60.4.56
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 93 5.3.2 ss-config The ms-config group define the commands that monitors or updates the configuration information. The user upon entering the ms-config command locks into the CLI to execute commands only related to MS configuration. FullMax# FullMax# ss-config FullMax(ss-config)# Command Purpose Privileges FullMax# ss-config The command allows the user to lock into the group ss-config and execute all the commands related to the group. A/O The commands supported by the ss-config group are. LostLostLostLost----dldldldl----mapmapmapmap----intervalintervalintervalinterval Time since last received DL-MAP message before downlink synchronization is considered lost in ms. Command Purpose Privileges FullMax(ss-config)# set lost-dl-map-interval <val> The command allows the user to update timer value since last received DL-MAP message before downlink synchronization is considered lost. A FullMax(ss-config)# show lost-dl-map-interval The command allows the user to display the timer value since last received DL-MAP message before downlink synchronization is considered lost. A/O Example: FullMax(ss-config) # set lost-dl-map-interval 300 Updated lost-dl-map-interval 300 milliseconds FullMax (ss-config) # show lost-dl-map-interval lost-dl-map-interval 300 milliseconds LostLostLostLost----ulululul----mapmapmapmap----intervalintervalintervalinterval Time since last received UL-MAP message before downlink synchronization is considered lost in ms. Command Purpose Privileges
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 94FullMax(ss-config)# set lost-ul-map-interval <val> The command allows the user to update timer value since last received UL-MAP message before downlink synchronization is considered lost. A FullMax(ss-config)# show lost-ul-map-interval The command allows the user to display the timer value since last received UL-MAP message before downlink synchronization is considered lost. A/O Example: FullMax(ss-config)# set lost-ul-map-interval 300 Updated lost-ul-map-interval 300 milliseconds FullMax(ss-config)# show lost-ul-map-interval lost-ul-map-interval 300 milliseconds ContentionContentionContentionContention----rngrngrngrng----retriesretriesretriesretries Number of retries on contention ranging requests. Command Purpose Privileges FullMax(ss-config)# set contention-rng-retries <val> The command allows the user to update the contention ranging retries parameter. A FullMax(ss-config)#show contention-rng-retries The command allows the user to display the contention ranging retries parameter. A/O Example: FullMax(ss-config)# set contention-rng-retries 20 Updated contention-rng-retries 20 FullMax(ss-config)# show contention-rng-retries contention-rng-retries 20 RequestRequestRequestRequest----retriesretriesretriesretries Number of retries on bandwidth allocation request. Command Purpose Privileges FullMax(ss-config)# set request-retries <val> The command allows the user to update the number of retries on bandwidth allocation request. A FullMax(ss-config)# show request-retries The command allows the user to display the number of retries on bandwidth allocation request. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 95 Example: FullMax(ss-config)# set request-retries 88 Updated request-retries 88 FullMax(ss-config)# show request-retries request-retries 88 RegRegRegReg----requsetrequsetrequsetrequset----retries retries retries retries Number of retries on registration request. Command Purpose Privileges FullMax(ss-config)# set reg-requset-retries <val> The command allows the user to update the number of retries on registration request. A FullMax(ss-config)# show reg-requset-retries The command allows the user to display the number of retries on registration request. A/O Example: FullMax(ss-config)# set reg-requset-retries 8 Updated reg-requset-retries 8 FullMax(ss-config)# show reg-requset-retries reg-requset-retries 8 TTTT1111----timeouttimeouttimeouttimeout Wait for DCD timeout in milliseconds. Command Purpose Privileges FullMax(ss-config)# set t1-timeout <val> The command allows the user to update the DCD timeout parameter. A FullMax(ss-config)# show t1-timeout The command allows the user to display the DCD timeout parameter. A/O Example: FullMax(ss-config)# set t1-timeout 9000 Updated t1-timeout 9000 milliseconds. FullMax(ss-config)# show t1-timeout t1-timeout 9000 milliseconds. T2T2T2T2----timeouttimeouttimeouttimeout Wait for broadcast ranging timeout in milliseconds.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 96Command Purpose Privileges FullMax(ss-config)# set t2-timeout <val> The command allows the user to update the broadcast ranging timeout parameter A FullMax(ss-config)# show t2-timeout The command allows the user to display the broadcast ranging timeout parameter A/O Example: FullMax(ss-config) # set t2-timeout 8000 Updated t2-timeout 8000 milliseconds. FullMax(ss-config)# show t2-timeout t2-timeout 8000 milliseconds. T3T3T3T3----timeouttimeouttimeouttimeout Ranging response reception timeout following the transmission of Ranging Request in milliseconds. Command Purpose Privileges FullMax(ss-config)# set t3-timeout <val> The command allows the user to update the ranging response timeout parameter. A FullMax(ss-config)# show t3-timeout The command allows the user to display the ranging response timeout parameter. A/O Example: FullMax(ss-config)# set t3-timeout 45 Updated t3-timeout 45 milliseconds. FullMax(ss-config)# show t3-timeout T3-timeout 45 milliseconds. T4T4T4T4----timeouttimeouttimeouttimeout Wait for ranging opportunity or data grant. If pending until complete field was used earlier by this SS, then the value of that field shall be added to this interval in second. Command Purpose Privileges FullMax(ss-config)# set t4-timeout <val> The command allows the user to update the wait for ranging opportunity timeout parameter. A FullMax(ss-config)# show t4-timeout The command allows the user to display the wait for ranging opportunity timeout parameter. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 97 Example: FullMax(ss-config) # set t4-timeout 45 Updated t4-timeout 45 milliseconds. FullMax(ss-config)# show t4-timeout T4-timeout 45 milliseconds. T16T16T16T16----timeouttimeouttimeouttimeout Wait for Registration Response in milliseconds. Command Purpose Privileges FullMax(ss-config)#set t16-timeout <val> The command allows the user to update the Registration response wait timer. A FullMax (ss-config)#show t16-timeout The command allows the user to display the Registration response wait timer. A/O Example: FullMax(ss-config)#set t16-timeout 540 Updated t16-timeout 540 milliseconds. FullMax (ss-config) # show t16-timeout T16-timeout 540 milliseconds. T12T12T12T12----timeouttimeouttimeouttimeout Wait for UCD descriptor in milliseconds. Command Purpose Privileges FullMax(ss-config)# set t12-timeout <val> The command allows the user to update wait for UCD descriptor timer. A FullMax(ss-config)# show t12-timeout The command allows the user to display the wait for UCD descriptor timer. A/O Example: FullMax(ss-config) # set t12-timeout 12000 Updated t12-timeout 12000 milliseconds. FullMax (ss-config) # show t12-timeout t12-timeout 12000 milliseconds. T18T18T18T18----timeouttimeouttimeouttimeout
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 98Wait for SBC-RSP timeout in milliseconds. Command Purpose Privileges FullMax(ss-config)# set t18-timeout <val> The command allows the user to update wait for SBC-RSP timeout parameter. A FullMax(ss-config)# show t18-timeout The command allows the user to display the wait for SBC-RSP timeout parameter. A/O Example: FullMax(ss-config) # set t18-timeout 7000 Updated t18-timeout 7000 milliseconds. FullMax (ss-config) # show t18-timeout t18-timeout 7000 milliseconds. T19T19T19T19----timeouttimeouttimeouttimeout Time DL-channel remains unusable in ms. Command Purpose Privileges FullMax(ss-config)#set t19-timeout <val> The command allows the user to update time for DL-channel remains unusable in ms.. A FullMax(ss-config)#show t19-timeout The command allows the user to display the time for DL-channel remains unusable in ms. A/O Example: FullMax(ss-config)# set t19-timeout 7000 Updated t19-timeout 7000 milliseconds. FullMax(ss-config)# show t19-timeout t19-timeout 7000 milliseconds. T20T20T20T20----timeouttimeouttimeouttimeout Time SS searches for preambles on a given channel in milliseconds. Command Purpose Privileges FullMax(ss-config)#set t20-timeout <val> The command allows the user to update the time to search for preambles on a given channel. A FullMax(ss-config)#show t20-timeout The command allows the user to display time to search for preambles on a given channel. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 99Example: FullMax(ss-config) # set t20-timeout 600 Updated t20-timeout 600 milliseconds. FullMax (ss-config) # show t20-timeout t20-timeout 600 milliseconds. T21T21T21T21----timeouttimeouttimeouttimeout Time SS searches for DL-MAP on a given channel in milliseconds. Command Purpose Privileges FullMax(ss-config)#set t21-timeout <val> The command allows the user to update the time to search for DL-MAP on a given channel. A FullMax(ss-config)#show t21-timeout The command allows the user to display time to search for DL-MAP on a given channel. A/O Example: FullMax(ss-config)# set t21-timeout 1200 Updated t21-timeout 1200 milliseconds. FullMax(ss-config)# show t21-timeout t21-timeout 1200 milliseconds. 5.3.3 device The device group define the commands that monitors or updates the device related information in the private MIB. The user upon entering the device command locks into the CLI to execute commands only related to device. FullMax# FullMax# device FullMax(device)# Command Purpose Privileges FullMax# The command allows the user to lock into the group device and execute all the commands related to the group. A/O type type type type Type of the device (BS / MS / SS).
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 100Command Purpose Privileges FullMax(device)#show type The command allows the user display the device type (BS/MS/SS) A/O Example: FullMax(device)# show type type SS gposgposgposgpos The geographical position of the device , i.e. the real number describing the longitude and latitusde encoded as a printable string. Longitude - the precision is within the range -90..90 degrees.Positive numbers indicate locations north of the equator. Latitude - The precision is within the range -180..180 degrees.Positive numbers indicate locations east of the prime meridian Command Purpose Privileges FullMax(device)#set gpos <val> The command allows the user to send the command to the GPS avaliable on the system. A FullMax(device)#show gpos The command allows the user display geographical position of the device. A/O Example: FullMax(device)# set gpos 64.000 88.3400 updated gpos 64.000 88.3400 FullMax(device)# show gpos gpos 64.000 88.3400 bootbootbootboot----timetimetimetime The absolute time of last device boot up. Command Purpose Privileges FullMax(device)# show boot- timeThe command allows the user display the device boot up time. A/O Example: FullMax(device)# show boot-time boot-time 230404:18052008 commitcommitcommitcommit----savesavesavesave Setting this object to TRUE causes the device to write all configuration changes in FLASH memory. On next boot the changes will be relevant. If this operation does not occur, configuration changes will not be maintained through reset Reading this object always returns FALSE
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 101 Command Purpose Privileges FullMax(device)#set commit-save <val> The command allows the user to set the value to TRUE so as to save the configuration changes in FLASH. A FullMax(device)#show commit-save The command allows the user display the device commit-save A/O Example: FullMax(device)# set commit-save commit-save TRUE FullMax(device)# show commit-save commit-save FALSE gpsgpsgpsgps----cardcardcardcard GPS card availability in the device. Command Purpose Privileges FullMax(device)#show gps-card The command allows the user display the availability of GPS card in the device. A/O Example: FullMax(device)# show gps-card gps-card YES bpcbpcbpcbpc----hwhwhwhw----versionversionversionversion Hardware version of baseband processor card. Command Purpose Privileges FullMax(device)#show bpc-hw-version The command allows the user display the hardware version of baseband processor card. A/O Example: FullMax(device)# show bpc-hw-version bpc-hw-version 1.10 afeafeafeafe----hwhwhwhw----verververver Hardware version of the Analog Front End (AFE) Command Purpose Privileges FullMax(device)#show afe-hw-ver The command allows the user display the hardware version of AFE. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 102 Example: FullMax(device)# show afe-hw-ver device-afe-hw-version 1.3 afeafeafeafe----swswswsw----verververver Software version of the Analog Front End (AFE) Command Purpose Privileges FullMax(device)#show afe-sw-ver The command allows the user display the software version of AFE. A/O Example: FullMax(device)# show afe-sw-ver device-afe-sw-version 1.3 buildbuildbuildbuild----swswswsw----verververver Software version of the device general embedded software. Command Purpose Privileges FullMax(device)#show build-sw-ver The command allows the user display the software version of the software build A/O Example: FullMax(device)#show build-sw-ver build-sw-version 5.3.4 Measurements The Measurement group define the commands that monitors or updates the measurement related information in the private MIB. The user upon entering the device command locks into the CLI to execute commands only related to Measurement. FullMax# FullMax# measurement FullMax(measurement)# Command Purpose Privileges FullMax# measurement The command allows the user to lock into the group Measurement and execute all the commands related to this group. A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 103TemperatureTemperatureTemperatureTemperature Temperature degree in Celsius Command Purpose Privileges FullMax(measurement)#show temperature The command allows the user display temperature of the device. A/O FullMax(measurement)#track [-rN][-iN] temperature The command allows the user to display real time temperature sample of the device. A/O Example: FullMax(measurement)# show temperature Temperature 45 degrees-Celsius FullMax(measurement)# track –r3 –i2 temperature Temperature 45 degrees-Celsius Temperature 46 degrees-Celsius Temperature 45 degrees-Celsius VoltageVoltageVoltageVoltage Voltage measurement Command Purpose Privileges FullMax(measurement)# show voltage The command allows the user display voltage of the device. A/O FullMax(measurement)# track [-rN][-iN] voltage The command allows the user to display multiple voltage samples of the device. A/O Example: FullMax(measurement)# show voltage Voltage 3 volts FullMax(measurement)# track –r3 –i10 voltage Voltage 3 volts Voltage 3 volts Voltage 3 volts CurrentCurrentCurrentCurrent Current measurements Command Purpose Privileges FullMax(measurement)#show current The command allows the user display the current in the device. A/O FullMax(measurement)#track The command allows the user to A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 104[-rN][-iN] current. display multiple current measurements in the device Example: FullMax(measurement)# show current Current 2 amp FullMax(measurement)# track –r4 current Current 2 amp Current 2 amp Current 2 amp TxTxTxTx----powerpowerpowerpower Transmit power Command Purpose Privileges FullMax(measurement)#show tx-power The command allows the user display the transmit power. A/O FullMax(measurement #track [-rN][-iN] tx-power The command allows the user to display multple transmit power measurements. A/O Example: FullMax(measurement)# show tx-power Tx-power 45 dBm FullMax(measurement)# track –r2 tx-power Tx-power 45 dBm Tx-power 43 dBm RxRxRxRx----powerpowerpowerpower Receive power Command Purpose Privileges FullMax(measurement)#show rx-power The command allows the user display the receive power. A/O FullMax(measurement)#track [-rN][-iN] rx-power The command allows the user to display multiple receive power measurements. A/O Example: FullMax(measurement)# show rx-power rx-power 45 dBm FullMax(measurement)# track –r2 -i2 rx-power rx-power 45 dBm rx-power 45 dBm
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 105afeafeafeafe----temperaturetemperaturetemperaturetemperature Read the temperature from the Analog Front End. Command Purpose Privileges FullMax(measurement)#show afe-temperature The command allows the user display temperatue from Analog Front End. A/O. FullMax(measurement)#track [-rN][-iN] afe-temperature The command allows the user to display multiple temperatue measurements from Analog Front End A/O Example: FullMax(measurement)# show afe-temperatue afe-temperature 27 celcius FullMax(measurement)# track -r4 -i30 afe-temperatue afe-temperature 27 celcius afe-temperature 27 celcius afe-temperature 27 celcius afe-temperature 27 celcius afeafeafeafe----rssirssirssirssi Read the Receive Signal Strength Indicator (RSSI) from the Analog Front End. Command Purpose Privileges FullMax(measurement)#show afe-rssi The command allows the user display RSSI from Analog Front End. A/O FullMax(measurement)#track [-rN][-iN] afe-rssi The command allows the user to display multiple RSSI measurements from Analog Front End . A/O Example: FullMax(measurement)# show afe-rssi afe-rssi 80 dBm FullMax(measurement)# track -r4 -i30 afe-rssi afe-rssi 80 dBm afe-rssi 80 dBm afe-rssi 80 dBm afe-rssi 80 dBm 5.3.5 ss-private The bs-private group define the commands that monitors or updates the private mib related information. The user upon entering the ss-private command locks into the CLI to execute commands only related to BS private mib. FullMax#
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 106 FullMax# ss-private FullMax(ss-private)# Command Purpose Privileges FullMax# ss-private The command allows the user to lock into the group ss-private and execute all the commands related to the group. A/O ssssssss----rxrxrxrx----amcamcamcamc----countcountcountcount----tabletabletabletable This table contains statistical information that can be used to characterize the adaptive modulation and coding performance in the uplink. Command Purpose Privileges FullMax(ss-private)#show ss-rx-amc-count-table <diuc-index> This command shows all the parameters and their values for RxAmcCountTable.. A/O Example: FullMax(ss-private)# show ss-rx-amc-count-table 1 ss-rx-octets for diuc-index 1 is 0 ss-rx-packets for diuc-index 1 is 0 ss-tx-erroredpackets for diuc-index 1 is 0 ssssssss----rxrxrxrx----diucdiucdiucdiuc----indexindexindexindex The Downlink Interval Usage Code indicates the uplink burst profile in the UCD message. Command Purpose Privileges FullMax(ss-private)# show ss-rx-diuc-index This command allows the users to display the avaliable diuc-index A/O Example: FullMax(ss-private)# show ss-rx-diuc-index ss-ul-diuc-index: 1 ss-ul-diuc-index: 2 ss-ul-diuc-index: 3 ss-ul-diuc-index: 4 ss-ul-diuc-index: 5 ss-ul-diuc-index: 6 ss-ul-diuc-index: 7 ss-ul-diuc-index: 8 ss-ul-diuc-index: 9 ss-ul-diuc-index: 10 ssssssss----rxrxrxrx----octetsoctetsoctetsoctets This object counts the number of octets received in the downlink using the downlink burst profile indexed by diuc-index.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 107 Command Purpose Privileges FullMax(ss-private)#show ss-rx-octets <diuc-index> This command allows the user to display the number of octets received in DL burst profile indexed by diuc-index. A/O Example: FullMax(ss-private)# show ss-rx-octets 1 ss-rx-octets for diuc-index 1 is 0 ssssssss----rxrxrxrx----packetspacketspacketspackets This object counts the number of packets received in the downlink using the downlink burst profile indexed by Command Purpose Privileges FullMax(ss-private)#show ss-rx-packets <diuc-index> This Command allows the user to display the number of packets received in DL burst profile indexed by diuc-index A/O Example: FullMax(ss-private)#show ss-rx-packets 1 ss-rx-packets for diuc-index 1 is 0 ssssssss----rxrxrxrx----erroredPacketserroredPacketserroredPacketserroredPackets Command Purpose Privileges FullMax(ss-private)#show ss-rx-erroredPackets <diuc-index> This command allows the use rto display the number of errored packets indexed by diuc-index A/O Example: FullMax(ss-private)# show ss-rx-erroredPackets 1 ss-tx-errored packets for uiuc index 1 is 0 ssssssss----txtxtxtx----amcamcamcamc----countcountcountcount----tabletabletabletable This table contains statistical information that can be used to characterize the adaptive modulation and coding performance in the downlink. Command Purpose Privileges FullMax(ss-private)#show ss-tx-amc-count-table <uiuc-index> This command allows the user to display the parametes and values of the TxAmcCount Table. A/O Example: FullMax(ss-private)# show ss-tx-amc-count-table 1 ss-tx-octets for uiuc-index 1 is 0
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 108 ss-tx-packets for uiuc-index 1 is 0 ssssssss----txtxtxtx----uiucuiucuiucuiuc----indexindexindexindex The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message. Command Purpose Privileges FullMax(ss-private)# show ss-tx-uiuc-index This command allows the user to display avaliable uiuc- indices A/O Example: FullMax(ss-private)# show ss-tx-uiuc-index ss-dl-uiuc-index: 0 ss-dl-uiuc-index: 1 ss-dl-uiuc-index: 2 ss-dl-uiuc-index: 3 ss-dl-uiuc-index: 4 ss-dl-uiuc-index: 5 ss-dl-uiuc-index: 6 ss-dl-uiuc-index: 7 ss-dl-uiuc-index: 8 ss-dl-uiuc-index: 9 ss-dl-uiuc-index: 10 ss-dl-uiuc-index: 11 ss-dl-uiuc-index: 12 ssssssss----txtxtxtx----octetsoctetsoctetsoctets This object counts the number of octets transmitted in the uplink using the uplink burst profile indexed by uiuc-index Command Purpose Privileges FullMax(ss-private)#show ss-tx-octets <uiuc-index> This command allows the user to display the Octets indexed by uiuc-index. A/O Example: FullMax(ss-private)# show ss-tx-octets 1 ss-tx-octets for uiuc-index 1 is 0 ssssssss----txtxtxtx----packetspacketspacketspackets This object counts the number of packets transmitted in the uplink using the uplink burst profile indexed by uiuc-index . Command Purpose Privileges FullMax(ss-private)#show ss-tx-packets <diuc-index> This command allows the user to display the packets in UL burst indexed by uiuc-index A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 109 Example: FullMax(ss-private)# show ss-tx-packets 1 ss-tx-packets for uiuc-index 1 is 0 cmncmncmncmn----sfsfsfsf----tabletabletabletable This Table measures service flow traffic Command Purpose Privileges FullMax(ss-private)# show cmn-sf-table <sfid> This command allows the user to display the parameters and values for cmn-sf-table for this SFID A/O Example: FullMax(ss-private)#show cmn-sf-table 2001 sf-total-octets for sfid 2001 is 0 sf-total-pkts for sfid 2001 is 0 sf-errored-pkts for sfid 2001 is 0 sf-frag-orig for sfid 2001 is 0 sf-frag-total for sfid 2001 is 0 sf-missing-frag for sfid 2001 is 0 cmncmncmncmn----pmpmpmpm----sfidsfidsfidsfid Command Purpose Privileges FullMax(ss-private)#show cmn-pm-sfid This command allows the user to display the avlaibale SFID. A/O Example: FullMax(ss-private)# show cmn-pm-sfid cmn-pm-sfid 2001 cmn-pm-sfid 2002 cmn-pm-sfid 3000 sfsfsfsf----totaltotaltotaltotal----octetsoctetsoctetsoctets This determines the total octets received/transmitted on this service flow. Command Purpose Privileges FullMax(ss-private)#show sf-total-octets <sfid> This command allows the user to diplay the total octets received or transmitted for this service-flow. A/O Example: FullMax(ss-private)# show sf-total-octets 2001 sf-total-octets for sfid (2001) : 1000
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 110sfsfsfsf----totaltotaltotaltotal----pktspktspktspkts This determines the total number of packets received /transmitted on this service flow. Command Purpose Privileges FullMax(ss-private)#show sf-total-pkts <sfid> This Command allows the user to display the total packets received or trasmitted for this service-flow A/O Example: FullMax(bs-private)#show sf-total-pkts 2001 sf-total-pkts for sfid (2001): 22 sfsfsfsf----errorederrorederrorederrored----pktspktspktspkts This determines number of packets that were dropped due to missing fragments / bad ARQ blocks. Command Purpose Privileges FullMax(ss-private)#show sf-errored-pkts <sfid> This Command Allows the user to display the total errored packets received or transmitted for this service flow. A/O Example: FullMax(ss-private)# show sf-errored-pkts 2001 sf-errored-pkts for sfid (2001): 1 sfsfsfsf----fragfragfragfrag----origorigorigorig This determines number of fragments / ARQ blocks originally transmitted/received on this service flow. Command Purpose Privileges FullMax(ss-private)# show sf-frag-orig <sfid> This Command allows the user to display the total fragments received or transmitted originally on this service flow. A/O Example: FullMax(ss-private)# show sf-frag-orig 2001 sf-frag-orig for sfid (2001) : 2 sfsfsfsf----fragfragfragfrag----totaltotaltotaltotal This determines total fragments / ARQ blocks transmitted / received on this service flow.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 111Command Purpose Privileges FullMax(ss-private)# show sf-frag-total <sfid> This Command allows the user to display the total fragments received or transmitted on this service flow. A/O Example: FullMax(ss-private)# show sf-frag-total 2001 sf-frag-total for sfid (2001): 2 sfsfsfsf----missingmissingmissingmissing----fragfragfragfrag Description This determines the number of missing received fragments received or NACK. Command Purpose Privileges FullMax(ss-private)# show sf-missing-frag <sfid> This command allows the user to display the number of missing received fragments or NACK. A/O Example: FullMax(ss-private)# show sf-missing-frag 2001 sf-missing-frag for sfid (2001): 1 5.3.6 ss-chconfig The ss-chconfig group define the commands that monitors or updates the channel config MIB related information. The user upon entering(locking) the ss-chconfig group can execute commands only related to ss-chconfig group. FullMax# FullMax# ss-chconfig FullMax(ss-chconfig)# Command Purpose Privileges FullMax#ss-chconfig The command allows the user to lock into the group ss-chconfig and execute all the commands related to the group. A/O ChannelChannelChannelChannel----configconfigconfigconfig----tabletabletabletable Each entry in the table contains optional channels configuration. A table can include a single active channel configuration and some inactive channel configurations A MS when searching for a new BS will scan the table for available channels.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 112Command Purpose Privileges FullMax(ss-chconfig)#show ss-channel-config-table <chn-index> The command allows the user display the channel configuration based on index. A/O A/O Example: FullMax(ss-chconfig)# show channel-config-table 1 center-channel-frequency for chn-index 1 is 12000 Hz center-bandwidth for chn-index 1 is 120 Hz center-config-status for chn-index 1 is ACTIVE ChannelChannelChannelChannel----configconfigconfigconfig----indexindexindexindex Index in channel-config-table. Command Purpose Privileges FullMax(ss-chconfig)# show channel-config-index The command allows the user display all the channel configuration indices A/O Example: FullMax(ss-chconfig)# show channel-config-index Channel-config-index 1 Channel-config-index 2 CenterCenterCenterCenter----channelchannelchannelchannel----frequefrequefrequefrequencyncyncyncy sets an optional center frequency for the transmitter and receiver Units are in Hz Command Purpose Privileges FullMax(ss-chconfig)# show center-channel-frequency <chn-index> The command allows the user display center frequencies for the given index. A/O Example: FullMax(ss-chconfig)# show center-channel-frequency 1 center-channel-frequency for chn-index 1 16000 Hz ChannelChannelChannelChannel----bandwidthbandwidthbandwidthbandwidth sets the bandwidth of the channel in the associated center frequency Units are in Hz. Command Purpose Privileges FullMax(ss-chconfig)#show center-bandwidth <chn-index> The command allows the user display bandwidth for the given index. A/O Example: FullMax(ss-chconfig)# show center-bandwidth 2
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 113 center-bandwidth for chn-index 2 is 1600 Hz samplingsamplingsamplingsampling----clockclockclockclock The channel sampling clock Command Purpose Privileges FullMax(ss-chconfig)#show sampling-clock <chn-index> The command allows the user display sampling clock time for the given index. A/O Example: FullMax(ss-chconfig)# show sampling-clock 2 sampling-clock for chn-index 2 is 16 filterfilterfilterfilter----idididid The ID of the PHY filter to use for this channel. Command Purpose Privileges FullMax(ss-chconfig)#show filter-id <chn-index> The command allows the user display filter id for the given index. A/O Example: FullMax(ss-chconfig)# show filter-id 2 filter-id for chn-index 2 is 16 ChannelChannelChannelChannel----configconfigconfigconfig----statusstatusstatusstatus Indicates the current state of this entry inactiveOption(0) - indicates that this entry is a scanning option that is not currently in use. currentActive(1) - indicates that this entry is the current channel channel configuration Command Purpose Privileges FullMax(ss-chconfig)#show channel-config-status <chn-index> The command allows the user display the current status for the given index A/O Example: FullMax(ss-chconfig)# show channel-config-status 2 channel-config-status for chn-index 2 is ACTIVE channelchannelchannelchannel----rowrowrowrow----statusstatusstatusstatus This determines the row status of the Channel config table for this config-index. Command Purpose Privileges FullMax(ss-chconfig)#show The command allows the user A/O
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 114channel-row-status display the row status for the given index Example: FullMax(ss-chconfig)# show channel-row-status 2 channel-row-status for chn-index 2 is ACTIVE 5.3.7 ss-trap The trap-ctrl-register group defines the commands that monitors or updates the trap mib related information. The user upon entering the trap-ctrl-register command locks into the CLI to execute commands only related to BS and MS trap control register mib. FullMax# FullMax# ss-trap FullMax (ss-trap) # Command Purpose Privileges FullMax# ss-trap The command allows the user to lock into the group ss-trap and execute all the commands related to the group A/O Within this group we can get the following parameters. SstrapControlRegister PriTrapControlRegister. ssssssss----traptraptraptrap----controlcontrolcontrolcontrol----register register register register The parameter is used to enable or disable the SS traps. Command Purpose Privileges FullMax(ss-trap)# set ss-trap-control-register <val> (enable or disable) The command allows the user to enable or disable the SS traps A FullMax(ss-trap)#show ss-trap-control-register The command allows the user display the enable or disable status of the SS traps. A/O Example: FullMax(ss-trap)# set ss-trap-control-register 0 Updated ss-trap-control-register 0 (disable) FullMax(ss-trap)# show ss-trap-control-register ss-trap-control-register 0 (disable) RssiRssiRssiRssi----lowlowlowlow----thresholdthresholdthresholdthreshold Low Rssi threshold for generating the RSSI alarm trap.
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 115Command Purpose Privileges FullMax(ss-trap)# set rssi-low-threshold <val> The command allows the user to update the lower threshold for generating RSSI alaram trap A FullMax(ss-trap)#show rssi-low-threshold The command allows the user to display the lower threshold for generating RSSI alaram trap A/O Example: FullMax(ss-trap)# set rssi-low-threshold 34 Updated rssi-low-threshold 34 dBm FullMax(ss-trap)# show rssi-low-threshold rssi-low-threshold 34 dBm RssiRssiRssiRssi----highhighhighhigh----thresholdthresholdthresholdthreshold High Rssi threshold for generating the RSSI alarm trap. Command Purpose Privileges FullMax(ss-trap)# set rssi-high-threshold <val> The command allows the user to update the higher threshold for generating RSSI alaram trap A FullMax(ss-trap)# show rssi-high-threshold The command allows the user to display the higher threshold for generating RSSI alaram trap. A/O Example: FullMax(ss-trap)# set rssi-high-threshold 34 Updated rssi-high-threshold 54 dBm FullMax(ss-trap)# show rssi-high-threshold rssi-high-threshold 54 dBm privateprivateprivateprivate-trap-ctrl The object is used to enable or disable Base Station traps From left to right, the set bit indicates the corresponding Base Station trap is enabled. { wmanPriPowerStatusChange (0), wmanPriFanStatusChange (1), wmanPriTemperatureChange (2), wmanPriConfigChange (3), wmanPriAfeBitError (4) } Command Purpose Privileges FullMax(ss-trap)#set private-trap-ctrl <val> This command allows the user to display the value of the private trap control A
FullMax BS100 and MS400 User Manual Version 1.1 Full Spectrum Confidential 116FullMax(ss-trap)#show private-trap-ctrl This command allows the user to display the value of the private trap control A/O Example: FullMax(ss-trap)# set private-trap-ctrl 21 updated private-trap-ctrl { wmanPriPowerStatusChange(0), wmanPriPowerStatusChange(2), wmanPriPowerStatusChange(4)} FullMax(ss-trap)# show private-trap-ctrl private-trap-ctl enabled { wmanPriPowerStatusChange(0), wmanPriPowerStatusChange(2), wmanPriPowerStatusChange (4)}

Navigation menu