Ondas Networks FS-NPCS000 PtMP Broadband Wireless System User Manual FCC Part 15

Download:
Mirror Download [FCC.gov]
Document ID	1252905
Application ID	OaG/xdy4/MpVBpZQU3weEQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	75.75kB (946871 bits)
Date Submitted	2010-03-16 00:00:00
Date Available	2010-03-16 00:00:00
Creation Date	2010-03-10 11:30:40
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2010-03-10 11:31:09
Document Title	FCC Part 15
Document Creator	Acrobat PDFMaker 9.1 for Word
Document Author:	kgrzovic

Rhein Tech Laboratories, Inc.
360 Herndon Parkway
Suite 1400
Herndon, VA 20170
http://www.rheintech.com
Appendix J :
Client: Full Spectrum Inc.
Models: BS100 & MS400
FCC ID: X27-FS-NPCS000
Standard: FCC Part 24
Report #: 2009306
Manual
Please refer to the following pages.
42 of 46
Fullax BS100 and MS400 User Manual Version 1.1
FullMax BS100 and MS400 User
Manual
Version 1.1
March 9, 2010
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
Table of Contents
Overview ........................................................................................................ 3
FullMax Description ....................................................................................... 4
2.1
System Description .............................................................................. 4
2.2
BS100 and MS400 Hardware Architecture ......................................... 5
2.3
FullMax BS100 and BS400 Software Architecture ........................... 11
FullMax BS100 and MS400 Embedded Software Functionality ................... 12
FullMax System Installation and Commissioning ......................................... 14
4.1
Enclosure of BS100 and MS400 ........................................................ 14
4.2
Connecting the BS100 and MS400 .................................................... 14
4.3
FullMax BS100 & MS400 Tune Up and Alignment Procedures....... 15
4.4
CLI Commands for BS100 ................................................................. 16
4.5
Monitoring the BS / MS with FullMax NMS ....................................... 17
FullMax system operation ............................................................................ 18
5.1
Operation Restrictions ....................................................................... 18
5.2
BS100 Operation................................................................................. 19
5.2.1 Main Group ................................................................................................... 19
5.2.2 mac-config .................................................................................................... 21
5.2.3 ul-config ........................................................................................................ 28
5.2.4 dl-config ........................................................................................................ 40
5.2.5 zone-config ................................................................................................... 45
5.2.6 bs-cap-config................................................................................................. 51
5.2.7 bs-burst-profile .............................................................................................. 53
5.2.8 bs-ss-action ................................................................................................... 56
5.2.9 ss-registered .................................................................................................. 57
5.2.10
ss-ip ........................................................................................................... 59
5.2.11
device ........................................................................................................ 61
5.2.12
Measurements ........................................................................................... 64
5.2.13
pkm–config ............................................................................................... 67
5.2.14
bs-private................................................................................................... 70
5.2.15
trap-config ................................................................................................. 76
5.2.16
lapc-config ................................................................................................ 78
5.3
MS400 Operation ................................................................................ 92
5.3.1 Main Group ................................................................................................... 92
5.3.2 ss-config ........................................................................................................ 93
5.3.3 device ............................................................................................................ 99
5.3.4 Measurements ............................................................................................. 102
5.3.5 ss-private ..................................................................................................... 105
5.3.6 ss-chconfig .................................................................................................. 111
5.3.7 ss-trap .......................................................................................................... 114
Annex A: Frequency Reuse Schemes ........... Error! Bookmark not defined.
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
1 Overview
a) FullMax is a Point to Multipoint (PtMP) broadband wireless system based on the
WiMAX-e (IEEE 802.16e-2005) protocol with modifications needed to enable its
operation in the Narrow PCS band (NPCS). The system consists of BS100 Base
Stations, MS400 Mobile or Fixed subscriber stations, standard backhaul
networking equipment connecting the BS100 Base Stations to a Router at the
Network Operating Center (NOC) and a Network Management System (NMS).
b) FullMax main modifications relative to the IEEE802.16e-2005 air interface
protocol are:
1) The RF front end can tune to the enter frequencies within the following NPCS
channels:
a. 940.3000 – 940.8000 (500 kHz)
b. 901.3000 – 901.7500 (450 kHz)
c. 901.3000 – 901.7000 (400 kHz)
d. 901.3500 – 901.7500 (400 kHz)
e. 930.0000 – 930.4000 (400 kHz)
f. 930.6000 – 931.0000 (400 kHz)
g. 940.3000 – 940.7500 (450 kHz)
h. 940.3000 – 940.7000 (400 kHz)
i. 940.3500 – 940.7500 (400 kHz)
2) The BS100& MS400 operate in 400 KHz, 450 KHz and 500 KHz wide
channels which are available in the NPCS band.
3) The BS100 and MS400 have analog and digital filters which are designed to
meet the FCC Part 24 spectral mask in the transmit direction and the channel
selectivity in the receive direction.
c) Outline of the document:
1) Paragraph 2: FullMax system description
2) Paragraph 3: FullMax system operation
3) Paragraph 4: BS100 and MS400 installation and commissioning.
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
2 FullMax Description
2.1 System Description
a) FullMax system architecture is described in figure 2-1 below. The system is used
to establish private, multi-cell, Point to Multipoint broadband wireless service for
electrical utilities and other mission critical industries. It supports both fixed and
mobile applications. FullMax BS’s are typically installed in the existing Private
Land Mobile Radio (PLMR) towers serving their respective cells. Wireless
backhaul facilities are used to connect the BS’s to the central site of the system.
FullMax fixed and mobile SS’s are deployed throughout the tower’s serving area.
BS
BS
BS
Fig. 2-1: FullMax system architecture
b) FullMax operates in unpaired spectrum using Time Division Duplex (TDD).
FullMax also operates in paired spectrum employing each portion of the paired
spectrum as an independent unpaired spectrum.
c) FullMax BS100 is designed to support a single sector and as such, it supports the
construction of a Base Station with multiple sectors (1, 2, 3 or more). An external
bridge/router is used to forward/route the traffic to the appropriate sector. Note
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
that the most common deployment is a 3 sector configuration. The sector
configuration dictates the type of antenna that should be used.
d) FullMax supports various frequency reuse schemes as outlined in Annex A to this
document.
e) The FullMax BS antenna is typically installed at an existing utility tower. The
antenna should be installed as high on the tower as possible. The BS also employs
a GPS antenna for TDD framing synchronization.
f) FullMax MS400 can be used as either a fixed indoor Subscriber Station with an
outdoor antenna or as a Mobile Station in a Utility truck. As a fixed SS, MS400
supports both Ethernet 100 Base T connectivity as well as serial RS232
connectivity. The serial connectivity is needed to support various legacy
applications like Supervisory Control And Data Acquisition (SCADA)
applications.
2.2 BS100 and MS400 Hardware Architecture
a) The FullMax BS100 & MS400 radio architecture is described in figure 2-1 and 2-2
below. It consists of a Baseband Processor Board (BBP), an Analog Front End (AFE)
section and a Low Voltage Power Supply (LVPS) board.
b) The BBP block diagram is described in figure 2-3. It is the heart of the FullMax radio.
It is designed to perform MAC, PHY, networking, network management and other
functions that are required in a broadband wireless BS and MS. The BBP has the
following main characteristics:
1) Processing resources:
a. A TI DSP and a Xilinx Spartan 3A FPGA to execute the PHY
layer
b. A Freescale PQ3 processor to execute the MAC layer and
complementary embedded software
2) A GPS time reference module is available for synchronization1 and for
location based services.
3) User interfaces: 100 Base T, RS232
4) Interface to the AFE is done through a digital I/Q interface.
c) The AFE section block diagram is described in figure 2-4. The AFE section performs
signal processing functions that are needed to deliver the signal to the antenna and to
receive the signal from the antenna. The AFE consists of:
1) A RF Small Signal (RFSS) board which contains a baseband section, an
IF section and an RF section.
e.g. for TDD frame synchronization.
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
a. The baseband section consists of an A/D, D/A, a programmable
receive baseband filter, a Digital Pre Distortion (DPD) Equalizer a
programmable sampling clock synthesizer and a FPGA.
b. The IF section consists of an IF LO, an I/Q
modulator/demodulator, an IF receive channel bank and an IF
transmit filter.
c. The RF section consists of a RF LO, an RF up/down convertor, an
RF receive channel bank and a RF transmit filter.
2) A RF Front End (RFFE) board which contains a RF PA, LNA, AGC and
T/R switch.
3) The AFE employs three 8051 microcontrollers for monitoring and control
of all aspects of the AFE operation. A serial interface protocol is available
to support control of the master housekeeping microcontroller on the
RFSS board by the main PQ3 processor on the BBP board.
Note: The AFE employs a non agile external RF bandpass filter which is shown as a
yellow block in the AFE block diagram in figure 4.
d) The Low Voltage Power Supply (LVPS) block diagram is described in figure 2-5.
The LVPS generates all the voltages that are needed at the BBP and the AFE. It is
designed for an input voltage range of 9 to 36 VDC to support power feed for a
vehicle battery. An optional external power brick is available if needed to support AC
or -48 VDC power feed.
Figure 2-1: FullMax BS100 & MS400 High Level Architecture
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
SDR BS/MS
On-Off
(For BS)
I-2
Low Voltage
Power Supply
(LVPS)
On-off
switch
(For BS)
I-5
Power -on
Indicator
I-6
BIT
Indicator
I-7
SDR
Wireless
connectivity
I-8
GPS
Wireless
connectivity
RFFE
SDR
Antenna
(For MS)
Analog Front End (AFE)
DC power
UI
I-1
Power
Conn.
Power LED
BIT LED
Power
Connector
10/100
Ethernet
I-3
RJ45
Ethernet
connector
AFE
Connector
RFSS
GPS
Antenna
BBP Board
GPS
SMA
RS232
COM port
I-4
DB-9
Serial
Connector
Processor
JTAG
Test
Connector
DSP
JTAG
FPGA
JTAG
Figure 2-2: FullMax BS100 & MS400 Block Diagram
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
Power -LED
POWER
SUPPLY
3.3V
5V
32V
15V
5V
3.3V
ENABLE 1.1V
CPLD
3.3V
5V
1.1V
ENABLE 1.1V
ENABLE 2.5V
ENABLE 1.8V
ENABLE 1.24V
MPC
ENABLE 1.2V
ENABLE
2.5V
ENABLE
1.8V
2.5V
1.1V
SENSOR
ENABLE
1.24V
1.8V
2.5V
SENSOR
MPC
ENABLE
1.2V
1.24V
1.8V
SENSOR
MPC I/O SUPPLY
TMS I/O SUPPLY
FPGA I/O SUPPLY
1.2V
1.24V
SENSOR
MPC
TMS(DDR2)
1.2V
SENSOR
FPGA
TMS
MCX
Conncector
2.54mm
10X2
DDR2
128MB
DDR2
128MB
DDR2
128MB
Integrated
Magnetic
Vertical
RJ45
Connector
125MHz
32MB
32MB
DDR2
DDR2
GPS
25MHz
16X
BUFFER
25MHz
PROM
MULTIPLIER
133MHz
Flash1
64MB
0MARVEL
MPC8548E
SWITCH
SGMII
GPIO-1,2
TMS320TCI6482
32V
5V
15V 3.3V
AFE
FPGA
XC3SD3400A
EMIFA
MUX
I2C
I2C
I2C EEPROM
RS232
Driver
Serial Configuration
UART 1 & 2
33.33MHz
MPC
JTAG
TRANSLA
TOR
RJ45
CONNECTOR
MPC TEMP
SENSOR
LED
TMS
JTAG
XILINIX
JTAG
Flash1
64MB
I/O - 16
DDR2
128MB
LED
LED
Figure 2-3: Baseband Processor (BBP) Board Block Diagram
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
Figure 2- 4: Analog Front End (AFE) Block Diagram
Full Spectrum Confidential
FullMax BS100 and MS400 User Manual Version 1.1
O/P
connectors
Low Voltage Power supply block diagram
I_IN_1
U5
28V/5A
LM5118
BuckBoost
I_OUT_1
Protection circuits
Reverse
Polarity
protection
9-36V DC
Control
I_IN _2
U3
5.15V/10A
TPS40054
Buck
I_OUT_2
To RFSS
U9
15V
@75mA
LM78L15AC
Fly back
U15
5V@2A
TPS75801
LDO
U17
3.3V@1.5A
EN5336Q
Buck
FUSE
U1
Under/ Over
Voltage
monitor
LT4356 )
U6
SMPS
Controller
(UC3843)
To RFFE
U8
32V@10mA
LM317L
Fly back
(U8)
FILTER
Over current
protection
28V/5A
To RFSS
To RFSS
To RFSS
I_IN
U4
5V@3A
TPS75801
LDO
U16
3.3V@3A
EN5364Q
Buck
To BBP
To BBP
Figure 2-5: Low Voltage Power Supply (LVPS) Block Diagram
Full Spectrum Confidential
10
FullMax BS100 and MS400 User Manual Version 1.1
2.3 FullMax BS100 and BS400 Software Architecture
a) FullMax BS100 and MS400 software architecture is described in figure 2-6
below. It consists of PHY layer, MAC layer and general purpose embedded
software components.
Figure 2-6: FullMax BS100 & MS400 software architecture
Full Spectrum Confidential
11
FullMax BS100 and MS400 User Manual Version 1.1
3 FullMax BS100 and MS400 Embedded Software
Functionality
a) FullMax BS100 and MS400 support the MAC and PHY layer requirements as
defined in the “WiMAX Forum Mobile System Profile Release 1.0 Approved
Specifications”. This section describes the complementary embedded software
that is not considered part of the MAC and the PHY layer software.
b) Networking:
o Supports communication over a 100 Base T Ethernet interface
o Supports IP host functionality: BS100 & MS400 have an IP address and
they support the following IP protocols: DHCP, ARP, ICMP, TFTP, FTP,
SNMP, ToD (RFC-868). Also, BS100 and MS400 have a read only MAC
address which is programmable during manufacturing.
o Learning bridge and layer 2 forwarding: BS100 and MS400 support
learning bridge functionality, maintain a Table of Connected Entities (TCE)
and use it to forward packets to the correct destination (Ethernet interface,
wireless interface or IP host)
c) QOS:
o Most of the QOS functionality is considered part of the MAC layer. The
general purpose embedded software provides complimentary QOS
functionality such as traffic prioritization.
d) Security:
o The general embedded software supports encryption and authentication
functionality and processes which are complimentary to the MAC layer
security functionality.
e) Provisioning:
o IP address provisioning (the BS100 and MS400 acquire an IP address from
an external standard DHCP server).
o Time provisioning (the BS100 and MS400 acquire date and time from an
RFC-868 Time server).
o EAP Provisioning (The BS100 and MS400 acquire the MSK Key from the
AAA server).
o Configuration provisioning (The BS100 and MS400 configuration
provisioning is done through CLI and through SNMP commands).
o QoS Provisioning (The BS100 and MS400 QOS provisioning is done
through SNMP commands).
Full Spectrum Confidential
12
FullMax BS100 and MS400 User Manual Version 1.1
f) Channel Acquisition
o The MS400 supports a pre-configured channel acquisition plan, i.e., a
preconfigured list of channel alternatives, characterized by their center
frequency and the bandwidth. The MS400 goes through the list and
performs successive channel acquisition attempts until an attempt is
successful.
o Criteria for channel acquisition success:
■ Successful registration if the MS400 was not registered prior to
channel acquisition.
■ Successful ranging if the MS400 was registered prior to channel
acquisition (i.e., in the case of moving to a new BS100).
Once a channel is successfully acquired, the parameters of the acquired
channel are saved to the MS400 flash memory and are used as first
acquisition option on MS400 power on.
g) Network Management Support
o The BS100 and MS400 have a SNMPv2c agent and they can be remotely
managed by FullMax Network Management System outlined in Paragraph 4
below.
o The BS100 and MS400 also support a Telnet based Command Line
Interface (CLI) protocol which can be used to configure all BS100 and
MS400 parameters.
h) Miscellaneous BS100 and MS400 hardware platform Management
o Remote and secure software download
o Initialization and configuration Persistence: The BS100 and MS400
support a CLI command that initiates the saving of the configuration in the
flash. Saved configuration is used after power off.
Full Spectrum Confidential
13
FullMax BS100 and MS400 User Manual Version 1.1
4 FullMax System Installation and Commissioning
4.1 Enclosure of BS100 and MS400
The BS100 and MS400 devices share the same enclosures
Figure 1: Top View
Figure 2: Bottom View (with FCC label)
Figure 3: Front View
Figure 4: Rear View
Figure 5: Right Side View
Figure 6: Left Side View
4.2 Connecting the BS100 and MS400
1. Place the enclosure in a stable location. Make sure that air can run
freely to the fans on the rear of the enclosure and the holes on the
enclosures sides.
2. Connect the cable from the Antenna to the device RF connector on the
enclosure left side.
Full Spectrum Confidential
14
FullMax BS100 and MS400 User Manual Version 1.1
3. Use an Ethernet cable to connect the device with end equipment
4. Connect the power cable to the power connector on the enclosure left
side.
5. Connect the power label to the power source.
4.3 FullMax BS100 & MS400 Tune Up and Alignment Procedures
1. Frequency and transmit power configuration of the FullMax BS100 and
MS400 is done by means of either a Command Line Interface (CLI) tool or
a Web based Network Management (NMS) tool.
2. The NMS/CLI tools is used to configure the following parameters:
a. BS100 parameters:
i. Center RF frequency
ii. Channel bandwidth
iii. Transmit power
b. MS400 parameters:
i. Maximum uplink transmit power
ii. An automatic channel acquisition table with up to 10 entries.
Each entry includes the center frequency and the channel
bandwidth.
3. The center frequency, channel bandwidth and transmit power at the
BS100 are configured statically by the NMS/CLI tool. This means that the
values will be maintained unless they are changed by the CLI/NMS tool.
4. The MS400 on the other hand, performs automatic channel acquisition by
selecting dynamically, the best channel (highest RSSI) from a list of up to
10 pre-configured entries (see paragraph 2bi above). The transmit power
of the MS is controlled by an automatic closed loop power control
algorithm running at the BS100. The transmit power of the MS will be
increased by the BS100 as the distance to the MS is increased (i.e., as
the path loss increases and the RSSI as measured by the BS100
becomes lower). Note however that the MS will not transmit above the
maximum uplink transmit power (see paragraph 2bii) even if ordered by
the BS100.
5. Both BS and MS employ an external RF bandpass filter as described in
Annex A to this document. This is an additional safeguard which
guarantees that the BS100 and the MS400 will not transmit outside the
band.
Full Spectrum Confidential
15
FullMax BS100 and MS400 User Manual Version 1.1
6. The remainder of the document describes the CLI commands that are
used to configure the BS100 and MS400 parameters described above.
4.4 CLI Commands for BS100
After logging in through telnet
[FULLMAX]$ Prompt
for user is displayed.
Type help or ? to look at different groups.
Lock to dl-config group using dl-config command
[FULLMAX]$
[FULLMAX]$ dl-config
You are locked to dl-config group.
Only dl-config operations are allowed.
Use help or ? for help.
[FULLMAX(dl-config)]$
For Frequency:
[FULLMAX(dl-config)]$ show center-freq
center-freq 940500 khz
[FULLMAX(dl-config)]$ set center-freq
updated center-freq 930800 khz
For Tx Power :
[FULLMAX(dl-config)]$ show tx_power
tx_power 9 dbm
[FULLMAX(dl-config)]$ set tx_power 16
updated tx_power 16 dbm
For Channel Bandwidth:
[FULLMAX(dl-config)]$ show bandwidth
bandwidth 500 khz
For FFT-Size:
Full Spectrum Confidential
16
FullMax BS100 and MS400 User Manual Version 1.1
[FULLMAX(dl-config)]$ show fft_size
fft_size 128fft
4.5 Monitoring the BS / MS with FullMax NMS
For monitoring the BS availability and performance it should be added to the
NMS.
Login to NMS as an 'Admin'.
If the BS100 is located in a new tower:
On NMS menu select: Admin 
New BS Tower
Type in tower name
Click 'Save'
On NMS menu select: Admin 
New BS Sector
Type in a 'sector name'
Select the tower on which the sector is installed
Add the BS100 IP address
Click 'Save'
The BS100 availability and performance will now be monitored by the NMS
Full Spectrum Confidential
17
FullMax BS100 and MS400 User Manual Version 1.1
5 FullMax system operation
5.1 Operation Restrictions
a) Changes or modifications not expressly approved by Full Spectrum Inc.
could void the user’s authority to operate the equipment.
b) While operated as a Mobile (non fixed application), the MS400 equipment
shall only be installed and operated with the antenna type, and antenna
gain not more than that approved for this certification (as per the table
below). The antenna will be installed with minimum separation distance
between the antenna and the general public and between the antenna and
the trained personnel during normal operation as stated in the table below
for the respective antenna gains.
c) An example of an antenna authorized for use with the MS400 while used
in a mobile application is Laird # B8965C Mobile Load Coil Antenna with
unity gain in the horizontal direction and with 5 dBi vertical gain.
Environment
Numeric
Gain
Average
Power (W)
Separation
Distance
(cm)
Power
Density
(mW/cm2)
General
population/Uncontrolled
3.16
3.1
36
0.6
Occupational/Controlled
3.16
3.1
20
General
population/Uncontrolled
20
3.1
91
0.6
Occupational/Controlled
20
3.1
41
d) This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
Full Spectrum Confidential
18
FullMax BS100 and MS400 User Manual Version 1.1
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
5.2 BS100 Operation
FullMax BS CLI supports the following commands. The access to this commands are
based on the user privileges. The Admin has the privilege to control and monitor all the
information supported by the FullMax BS CLI commands, where as the operator has
limited privileges. After the successful authentication, the user Is permitted access to the
command line interface. Based on the user privileges, the help menu will be displayed to
the user.
5.2.1 Main Group
When user logs in to the CLI it will lock to the default group which is the main
group.When ever the user enters the Main group,CLI will display the main
prompt .Help command in main group will show the commands supported in
main group along with the group lock commands. Only commands related to
main group can be executed in main group.
FullMax#
ipip-address
System IP address.
Command
FullMax# set ip-address

FullMax# show ipaddress
Purpose
Updates the system IP
address.
Displays the system IP
address.
Privileges
A/O
A/O
Example:
FullMax#set ip-address 10.60.4.42
Updated IP address: 10.60.4.42
FullMax# show ip-address
IP address: 10.60.4.56
dhcpdhcp-configconfig-serverserver-ip
DHCP server IP address.
Command
Purpose
Allows
the user to update the
FullMax#set dhcp-configBS with the DHCP server IP
server-ip 
address.
Allows the user to display the
FullMax# show dhcpremote DHCP server IP
config-server-ip
address
Full Spectrum Confidential
Privileges
A/O
A/O
19
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax# set dhcp-config-server-ip 10.60.1.11
Updated DHCP server IP 10.60.1.11
FullMax# show dhcp-config-server-ip
DHCP server IP 0.0.0.0
dhcpdhcp-configconfig-remoteremote-id
DHCP remote ID.
Command
FullMax# set dhcpconfig-remote-id 
FullMax# show dhcpconfig-remote-id
Purpose
Allows the user to update the
DHCP remote ID
Privileges
A/O
Allows the user to displays the
DHCP remote ID
A/O
Example:
FullMax# set dhcp-config-remote-id 0019D1:50CC62
Updated dhcp-config-remote-id 0019D1:50CC62
FullMax# show dhcp-config-remote-id
dhcp-config-remote-id 0019D1:50CC62
dhcpdhcp-configconfig-circuitcircuit-id
DHCP circuit ID
Command
FullMax# set dhcpconfig-circuit-id
FullMax# show dhcpconfig-circuit-id
Purpose
Allows the user to updates the
DHCP circuit ID
Allows the user to display the
DHCP circuit ID
Privileges
A/O
A/O
Example:
FullMax# set dhcp-config-circuit-id 3
Updated dhcp-config-circuit-id 3
FullMax# show dhcp-config-circuit-id
dhcp-config-circuit-id 0
Full Spectrum Confidential
20
FullMax BS100 and MS400 User Manual Version 1.1
5.2.2 mac-config
mac-config group defines the commands that monitors or updates the MAC configuration
information. The user upon entering the mac-config command , locks into this particular
group to execute commands only related to BS configuration.
FullMax#
FullMax# mac-config
FullMax(mac-config)#
Command
Purpose
Privileges
FullMax# macconfig
The command allows the user to lock into
the group mac-config and execute all the
commands related to the group.
A/O
The commands supported by the mac-config group are
dcd-interval
The command describes the time between transmissions of DCD messages in
milliseconds.
Command
FullMax(mac-config)# set
dcd-interval 
FullMax(mac-config)#show
dcd-interval
Privileges
Purpose
The command allows the user to
update the transmission time
between to DCD messages.
The command allows the user to find A/O
the time interval for transmission of
consecutive DCD messages.
Example:
FullMax(mac-config)# set dcd-interval 30
Updated dcd-interval 30 milliseconds
FullMax(mac-config)# show dcd-interval
dcd-interval 30 milliseconds
ucducd-interval
The command describes the time between transmissions of UCD messages in
milliseconds.
Command
FullMax(mac-config)# set
ucd-interval 
Purpose
The command allows the user to update the
transmission time between to UCD
messages.
Full Spectrum Confidential
Privileges
21
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(mac-config)# show
ucd-interval
The command allows the user to find the
time interval for transmission of consecutive
UCD messages.
A/O
Example:
FullMax(mac-config)# set ucd-interval 30
Updated ucd-interval 30 milliseconds
FullMax(mac-config)# show ucd-interval
ucd-interval 30 milliseconds
dcddcd-transition
The number of frames from the end of the frame carrying the DCD message the BS shall
wait after transmitting a DCD message with an incremented Configuration Change count
before issuing a DL-MAP message referring to Downlink Burst profiles defined in that
DCD message.
Command
FullMax(mac-config)# set
dcd-transition 
FullMax(mac-config)#show
dcd-transition
Purpose
Privileges
This command allows the user to change A
the configuration count, the BS shall wait
to transmit DL-MAP after transmitting
the DCD message.
The command allows the user to find the A/O
configuration count, the BS shall wait
(no. of frames) to transmit DL-MAP after
transmitting the DCD message.
Example:
FullMax(mac-config)# set dcd-transition 30
Updated dcd-transition 30 (MAC Frames)
FullMax(mac-config)# show dcd-transition
dcd-transition 30 (MAC Frames)
ucducd-transition
The number of frames from the end of the frame carrying the UCD message the BS shall
wait after transmitting a UCD message with an incremented Configuration Change count
before issuing a UL-MAP message referring to Uplink Burst profiles defined in that UCD
message.
Command
FullMax(mac-config)# set
ucd-transition 
FullMax(mac-config)#show
Purpose
This command allows the user to change the
configuration count, the BS shall wait to
transmit UL-MAP after transmitting the UCD
message.
The command allows the user to find the
Full Spectrum Confidential
22
Privileges
A/O
FullMax BS100 and MS400 User Manual Version 1.1
ucd-transition
configuration count, the BS shall wait (no. of
frames) to transmit UL-MAP after transmitting
the UCD message.
Example:
FullMax(mac-config)# set ucd-transition 30
Updated ucd-transition 30 (MAC Frames)
FullMax(mac-config)# show ucd-transition
ucd-transition 30 (MAC Frames)
DsxDsx-rsprsp-retries
Number of Timeout Retries on DSA/DSC/DSD Responses.
Command
FullMax(mac-config)# set
dsx-rsp-retries 
FullMax(mac-config)# show
dsx-rsp-retries
Purpose
The command updates the value of the
DSA/DSC/DSD responses retries
timeout.
The command displays the
DSA/DSC/DSD responses retries
timeout.
Privileges
A/O
Example:
FullMax(mac-config)#set dsx-rsp-retries 6
Updated dsx-rsp-retries 6.
FullMax(mac-config)#show dsx-rsp-retries
dsx-rsp-retries 3
DsxDsx-reqreq-retries
Number of Timeout Retries on DSA/DSC/DSD Requests.
Command
Purpose
Privileges
FullMax(mac-config)# set
dsx-req-retries 
FullMax(mac-config)#show
dsx-req-retries
The command updates the value of the
DSA/DSC/DSD requests retries timeout.
The command displays the
DSA/DSC/DSD requests retries timeout.
A/O
Example:
FullMax(mac-config)#set dsx-req-retries 6000
Updated dsx-req-retries 6000 milliseconds.
FullMax(mac-config)#show dsx-req-retries
dsx-req-retries 3.
Full Spectrum Confidential
23
FullMax BS100 and MS400 User Manual Version 1.1
T7-timeout
Wait for DSA/DSC/DSD Response Timeout in ms.
Command
FullMax (mac-config) #
set t7-timeout 
FullMax (mac-config) #
show t7-timeout
Purpose
The command updates the value of T7
timer, with in which the BS/SS should
wait for a DSx response.
The command displays the T7 timer,
configured to which the BS/SS should
wait for a DSx response.
Privileges
A/O
Example:
FullMax(mac-config)#set t7-timeout 300
Updated t7-timeout 300 milliseconds.
FullMax(mac-config)# show t7-timeout
t7-timeout 300 milliseconds.
T8T8-timeout
Wait for DSA/DSC/DSD Acknowledge Timeout in ms.
Command
FullMax(mac-config)# set
t8-timeout 
FullMax(mac-config)# show
t8-timeout
Purpose
The command updates the value of T8
timer, with in which the BS/SS should wait
for a DSx acknowledge.
The command displays the T8 timer,
configured to which the BS/SS should wait
for a DSx acknowledge.
Privileges
A/O
Example:
FullMax(mac-config)# set t8-timeout 100
Updated t8-timeout 100 milliseconds.
FullMax(mac-config)# show t8-timeout
t8-timeout 100 milliseconds.
T9-timeout
The time allowed between the BS sending a RNG-RSP to an SS, and receiving an SBCREQ from that same SS.
Command
FullMax(mac-config)# set
t9-timeout 
Purpose
The command updates the T9 timer value
that waits for an SBC-REQ from an MS to
Full Spectrum Confidential
Privileges
24
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(mac-config)#show
t9-timeout
which it has sent a RNG-RSP.
The command displays the T9 Timer value
configured in BS to wait for SBC-REQ
from an MS to which the BS has sent the
RNG-RSP.
A/O
Example:
FullMax(mac-config)#set t9-timeout 3200
Updated t9-timeout 3200 milliseconds
FullMax(mac-config)#show t9-timeout
t9-timeout 3200 milliseconds
T10-timeout
The maximum time allowed to wait for a dynamic service transaction to end.
Command
FullMax(mac-config)#set
t10-timeout 
FullMax(mac-config)#show
t10-timeout
Purpose
The command updates the T10 timer
value that waits for a dynamic service
transaction end.
The command displays the T10 timer
value that waits for a dynamic service
transaction end.
Privileges
A/O
Example:
FullMax(mac-config)# set t10-timeout 1000
Updated t10-timeout 1000milliseconds
FullMax(mac-config)# show t10-timeout
T10-timeout 1000milliseconds
T1313-timeout
Time allowed for an SS, following the receipt of a REG-RSP message to send a TFTPCPLT message to the BS.
Command
FullMax(mac-config)#set
t13-timeout 
FullMax(mac-config)#show
t13-timeout
Purpose
The command updates the T13 timer for
which the BS waits to receive TFTP-CPLT
message after sending the REG-RSP.
The command displays the T13 timer
configured at BS to wait for TFTP-CPLT
message after sending the REG-RSP
Privileges
A/O
Example:
FullMax(mac-config)# set t13-timeout 13000
Full Spectrum Confidential
25
FullMax BS100 and MS400 User Manual Version 1.1
Updated t13-timeout 13000 milliseconds
FullMax(mac-config)# show t13-timeout
t13-timeout 13000 milliseconds
T1717-timeout
Time allowed for SS to complete authorization and key exchange.
Command
FullMax(mac-config)#set
t17-timeout 
FullMax(mac-config)#show
t17-timeout
Purpose
Privileges
The command updates the value of T17
timer, with in which the SS should complete
the authorization and key exchange.
The command displays the T17 timer,
A/O
configured to which the SS should complete
the authorization and key exchange.
Example:
FullMax(mac-config)#set t17-timeout 6000
Updated t17-timeout 6000 milliseconds.
FullMax(mac-config)#show t17-timeout
t17-timeout 6000 milliseconds.
T2222-timeout
Time to wait for an ARQ-reset.
Command
FullMax(mac-config)# set
t22-timeout 
FullMax(mac-config)# show
t22-timeout
Purpose
The command updates the T22 timer for
which the BS waits for ARQ reset.
The command displays the T22 timer
configured at BS to wait for ARQ reset.
Privileges
A/O
Example:
FullMax(mac-config)# set t22-timeout 200
Updated t22-timeout 200 milliseconds
FullMax(mac-config)# show t22-timeout
t22-timeout 200 milliseconds
autoauto-sfidsfid-enabled
The command defines weather BS is allowed to autonomously allocate SFIDs. If the BS
is enabled with this feature, the BS can autonomously allocate SFIDs in configured SFID
range. An SF is autonomously when it is not provisioned and may be initiated either by
either BS or SS.
Full Spectrum Confidential
26
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(mac-config)# set
auto-sfid-enabled {enable
| disable }
FullMax(mac-config)# show
auto-sfid-enabled {enable
| disable }
Purpose
This command allows the user to
configure BS by allowing the BS to
autonomously allocate SFIDs.
Privileges
This command displays the user, weather
the BS is enabled/disabled to allocate
SFIDs.
A/
Example:
FullMax(mac-config)# set auto-sfid-enabled ENABLE
Updated auto-sfid-enabled ENABLED
FullMax(mac-config)# show auto-sfid-enabled
auto-sfid-enabled ENABLED
minmin-autoauto-sfidsfid-range
The command defines the minimum value of the SFID for the range allocated to support
the creation of service flows autonomously.
Command
FullMax(mac-config)# set
min-auto-sfid-range 
FullMax(mac-config)#show
min-auto-sfid-range
Purpose
This command allows the user to define
the minimum value of SFID to define the
range in which the BS can autonomously
create Service flows.
The command displays the user, the
minimum value of sfid from which the BS
can create service flows autonomously.
Privileges
A/O
Example:
FullMax(mac-config)# set min-auto-sfid-range 6200
Updated min-auto-sfid-range 6200
FullMax(mac-config)# show min-auto-sfid-range
Updated min-auto-sfid-range 6200
maxmax-autoauto-sfidsfid-range
The command defines the maximum value of the SFID for the range allocated to support
the creation of service flows autonomously.
Command
FullMax(mac-config)# set
max-auto-sfid-range 
FullMax(mac-config)# show
Purpose
This command allows the user to define the
maximum value of SFID range in which the
BS can autonomously create Service flows.
The command displays the user, the
Full Spectrum Confidential
Privileges
A/O
27
FullMax BS100 and MS400 User Manual Version 1.1
max-auto-sfid-range
maximum value of sfid upto which the BS
can create service flows autonomously.
Example:
FullMax(mac-config)# set max-auto-sfid-range 6300
Updated max-auto-sfid-range 6300
FullMax(mac-config)# show max-auto-sfid-range
max-auto-sfid-range 6300
all
This command displays all the parametrs values for the mac-config group in CLI.
Command
FullMax(mac-config)#show
all
Purpose
The command displays the user, the
value of all the mib parameters of tables
in the group.
Privileges
A/O
Example:
FullMax(mac-config)# show all
dcd-interval 5000 milliseconds
ucd-interval 5000 milliseconds
ucd-transition 0 (MAC Frames)
dcd-transition 0 (MAC Frames)
t9-timeout 8000 milliseconds
t13-timeout 0 milliseconds
t15-timer 0 milliseconds
t17-timeout 0 milliseconds
auto-sfid-enabled DISABLE
min-auto-sfid-range 0
max-auto-sfid-range 0
dsx-req-retries 3
dsx-rsp-retries 3
T7-timer 1000 milliseconds
t8-timer 300 milliseconds
t10-timer 3000 milliseconds
t22-timer 200 milliseconds
5.2.3 ul-config
The group defines the commands that monitors or updates the UCD channel attributes
that define the characteristics of uplink channels. The user upon entering the ul-config
command locks into the CLI to execute commands only related to BS uplink channel
characteristics.
Full Spectrum Confidential
28
FullMax BS100 and MS400 User Manual Version 1.1
FullMax#
FullMax# ul-config
FullMax(ul-config)#
Command
FullMax# ul-config
Purpose
The command allows the user to lock into the
group ul-config and execute all the
commands related to the group.
ct-based-reserve-timeout
The number of UL-MAPs to receive before contention-based reservation is attempted
again for the same connection.
Command
FullMax(ul-config)# set
ct-based-reserve-timeout

FullMax(ul-config)#show
ct-based-reserve-timeout
Purpose
The command allows the user to update
number of UL-MAPs to receive before
contention-based reservation is attempted
again for the same connection.
The command allows the user to display
number of UL-MAPs to receive before
contention-based reservation is attempted
again for the same connection.
Privileges
A/O
Example:
FullMax(ul-config)# set ct-based-reserve-timeout 30
Updated ct-based-reserve-timeout 30
FullMax(ul-config)# show ct-based-reserve-timeout
ct-based-reserve-timeout 30
uplink-center-frequency
Uplink center frequency (in KHz).
Command
FullMax(ul-config)#set
uplink-center-frequecy 
FullMax(ul-config)#show
uplink-center-frequecy
Purpose
The command allows the user to update
the uplink center frequency.
The command allows the user to display
the uplink center frequency.
Privileges
A/O
Example:
FullMax (ul-config) # set uplink-center-frequency 30
updated uplink-center-frequecy 30 KHz
FullMax (ul-config) # show uplink-center-frequency
uplink-center-frequecy 30 KHz
Full Spectrum Confidential
29
FullMax BS100 and MS400 User Manual Version 1.1
init-rng-codes
Number of initial ranging CDMA codes.
Command
FullMax(ul-config)# set
init-rng-codes 
FullMax(ul-config)#show
init-rng-codes
Purpose
The command allows the user to update
the Number of initial ranging CDMA
codes.
The command allows the user to display
the number of initial ranging CDMA
codes.
Privileges
A/O
Example:
FullMax(ul-config)# set init-rng-codes 10
Updated init-rng-codes 10
FullMax(ul-config)# show init-rng-codes
init-rng-codes 10
periodic-rng-codes
Number of periodic ranging CDMA codes.
Command
FullMax(ul-config)# set
periodic-rng-codes 
FullMax(ul-config)#show
periodic-rng-codes
Purpose
The command allows the user to update
the Number of periodic ranging CDMA
codes.
The command allows the user to display
the number of periodic ranging CDMA
codes.
Privileges
A/O
Example:
FullMax(ul-config)# set periodic-rng-codes 20
Updated periodic-rng-codes 20
FullMax(ul-config)# show periodic-rng-codes
periodic-rng-codes 20
bandwidth-request-codes
Number of bandwidth request codes.
Command
FullMax(ul-config)#set
bandwidth-requestcodes 
FullMax(ul-config)#show
Purpose
The command allows the user to update
the number of bandwidth request codes.
Privileges
The command allows the user to display
A/O
Full Spectrum Confidential
30
FullMax BS100 and MS400 User Manual Version 1.1
bandwidth-request-codes
the number of bandwidth request codes.
Example:
FullMax(ul-config)#set bandwidth-request-codes 20
Updated bandwidth-request-codes 20
FullMax(ul-config)#show bandwidth-request-codes
bandwidth-request-codes 20
per-rng-backoff-start
Initial backoff window size for periodic ranging contention expressed as a power of 2
Command
FullMax(ul-config)#set
per-rng-backoff-start

FullMax(ul-config)#show
per-rng-backoff-start
Purpose
The command allows the user to
update the initial backoff window
size for periodic ranging
contention.
The command allows the user to display
the initial backoff window size for
periodic ranging contention.
Privileges
A/O
Example:
FullMax (ul-config) # set per-rng-backoff-start 4
Updated per-rng-backoff-start 4
FullMax (ul-config) # show per-rng-backoff-start
per-rng-backoff-start 4
per-rng-backoff-end
Final backoff window size for periodic ranging contention, expressed as a power of 2
Command
FullMax(ul-config)# set
per-rng-backoff-end 
FullMax(ul-config)# show
per-rng-backoff-end
Purpose
The command allows the user to update
the final backoff window size for periodic
ranging contention.
The command allows the user to display
the final backoff window size for periodic
ranging contention.
Privileges
A/O
Example:
FullMax(ul-config)# set per-rng-backoff-end 8
Updated per-rng-backoff-end 8
Full Spectrum Confidential
31
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(ul-config)# show per-rng-backoff-end
per-rng-backoff-end 8
start-off-rng-codes
Indicates the starting number, of the group of codes used for uplink
Command
FullMax(ul-config)#set
start-off-rng-codes 
FullMax(ul-config)#show
start-off-rng-codes
Purpose
The command allows the user to update
the starting number of the codes used for
uplink
The command allows the user to display
the starting number of the codes used for
uplink.
Privileges
A/O
Example:
FullMax(ul-config)# set start-off-rng-codes 64
Updated start-off-rng-codes 64
FullMax(ul-config)# show start-off-rng-codes
start-off-rng-codes 64
permutation-base
Determines the UL_PermBase parameter for the sub carrier permutation to be used on
this uplink channel.
Command
FullMax(ul-config)# set
permutation-base 
FullMax(ul-config)# show
permuation-base
Purpose
The command allows the user to updates
the UL_PermBase parameter for the sub
carrier permutation to be used on this
uplink channel.
The command allows the user to display
the UL_PermBase parameter for the sub
carrier permutation to be used on this
uplink channel.
Privileges
A/O
Example:
FullMax(ul-config)# set permutation-base 127
Updated permutation-base 127
FullMax(ul-config)#show permutation-base
permutation-base 8
ul-alloc-sub-channel-bitmap
Full Spectrum Confidential
32
FullMax BS100 and MS400 User Manual Version 1.1
This is a bitmap describing the physical sub-channels allocated to the segment in the UL,
when using the uplink PUSC permutation. The LSB of the first byte shall correspond to
subchannel 0.
Command
FullMax(ul-config)# set
ul-alloc-sub-channelbitmap 
FullMax(ul-config)#show
ul-alloc-sub-channelbitmap
Purpose
The command allows the used to update
the ofdma subchannel allocation.
Privileges
The command allows the user to display
the ofdma subchannel allocation.
A/O
Example:
FullMax(ul-config)#set ul-alloc-sub-channel-bitmap
00110001
Updated ul-alloc-sub-channel-bitmap ff
FullMax(ul-config)# show ul-alloc-sub-channel-bitmap
ul-alloc-sub-channel-bitmap 00110001
band-amc-alloc-threshold
Threshold of the maximum of the standard deviations of the individual bands CINR
measurements over time to trigger mode transition from normal sub channel to Band
AMC.
Command
FullMax(ul-config)# set
band-amc-alloc-threshold

FullMax(ul-config)#show
band-amc-alloc-threshold
Purpose
Privileges
The command allows the user to update A
the parameter for AMC band allocation
Threshold.
The command allows the user to
display the parameter for AMC band
allocation threshold.
A/O
Example:
FullMax(ul-config)# set band-amc-alloc-threshold 64
Updated band-amc-alloc-threshold 64 dB
FullMax(ul-config)# show band-amc-alloc-threshold
band-amc-alloc-threshold 64 dB
bandband-amcamc-releaserelease-threshold
Threshold of the maximum of the standard deviations of the individual bands CINR
measurements over time to trigger mode transition from Band AMC to normal
subchannel.
Full Spectrum Confidential
33
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(ul-config)# set
band-amc-release-threshold

FullMax(ul-config)#show
band-amc-release-threshold
Purpose
The command allows the user to update
the parameter that defines the maximum
threshold for AMC band.
The command allows the user to display
the parameter that defines the maximum
threshold for AMC band.
Privileges
A/O
Example:
FullMax(ul-config)# set band-amc-release-threshold 56
Updated band-amc-release-threshold 56 dB
FullMax(ul-config)# show band-amc-release-threshold
band-amc-release-threshold 56 dB
bandband-amcamc-allocalloc-timer
Minimum required number of frames to measure the average and standard deviation for
the event of Band AMC triggering.
Command
Purpose
FullMax(ul-config)# set
band-amc-alloc-timer 
The command allows the user to update
the parameter that defines the minimum
required number of frames to measure
the average and standard deviation for
the event of Band AMC triggering.
The command allows the user to display
parameter that defines the minimum
required number of frames to measure
the average and standard deviation for
the event of Band AMC triggering.
FullMax(ul-config)#show
band-amc-alloc-timer
Privilege
A/O
Example:
FullMax(ul-config)# set band-amc-alloc-timer 22
Updated band-amc-alloc-timer 22 Frames
FullMax(ul-config)# show band-amc-alloc-timer
band-amc-alloc-timer 22 Frames
bandband-amcamc-releaserelease-timer
Minimum required number of frames to measure the average and standard deviation for
the event of Band AMC triggering.
Full Spectrum Confidential
34
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(ul-config)# set
band-amc-release-timer

FullMax(ul-config)#show
band-amc-release-timer
Purpose
The command allows the user to update
the parameter that defines the minimum
required number of frames to measure
the average and standard deviation for
the event of Band AMC triggering.
The command allows the user to display
parameter that defines the minimum
required number of frames to measure
the average and standard deviation for
the event of Band AMC triggering.
Privileges
A/O
Example:
FullMax(ul-config)#set band-amc-release-timer 22
Updated band-amc-release-timer 22 Frames
FullMax(ul-config)#show band-amc-release-timer
band-amc-release-timer 22 Frames
bandband-amcamc-retryretry-timer
Backoff timer between consecutive mode transitions from normal subchannel to Band
AMC when the previous request is failed.
Command
FullMax(ul-config)#set
band-amc-retry-timer 
FullMax(ul-config)#show
band-amc-retry-timer
Purpose
The command allows the user to
update the parameter band AMC retry
timer
The command allows the user to
display parameter band AMC retry
timer.
Privileges
A/O
Example:
FullMax(ul-config)# set band-amc-retry-timer 5
Updated band-amc-retry-timer 5
FullMax(ul-config)# show band-amc-retry-timer
band-amc-retry-timer 5
bandband-statstat-reprep-maxmax-period
Maximum period between refreshing the Band CINR measurement by the unsolicited
REP-RSP.
Command
FullMax(ul-config)# set
band-stat-rep-max-period

Purpose
The command allows the user to update the
maximum period between refreshing the
Band CINR measurement by the unsolicited
REP-RSP.
Full Spectrum Confidential
Privileges
35
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(ul-config)# show
band-stat-rep-max-period
The command allows the user to display the
maximum period between refreshing the
Band CINR measurement by the unsolicited
REP-RSP.
A/O
Example:
FullMax(ul-config)# set band-stat-rep-max-period 12
Updated band-stat-rep-max-period 12
FullMax(ul-config)# show band-stat-rep-max-period
band-stat-rep-max-period 12
upup-powerpower-adjadj-step
MS specific up power offset adjustment step.
Command
FullMax(ul-config)#set
band-stat-rep-max-period

FullMax(ul-config)#show
band-stat-rep-max-period
Purpose
The command allows the user to update
the maximum period between refreshing
the Band CINR measurement by the
unsolicited REP-RSP.
The command allows the user to display
the maximum period between refreshing
the Band CINR measurement by the
unsolicited REP-RSP.
Privileges
A/O
Example:
FullMax(ul-config)# set up-power-adj-step 12
Updated up-power-adj-step 12 (in 0.01 dB).
FullMax(ul-config)# show up-power-adj-step
up-power-adj-step 12 (in 0.01 dB).
down-power-offset-adj-step
MS specific down power offset adjumstment step.
Command
FullMax(ul-config)# set
down-power-offset-adj-step

FullMax ul-config)# show
down-power-offset-adj-step
Purpose
The command allows the user to update
the MS specific down power offset
adjustment step.
Privileges
The command allows the user to display
the MS specific down power offset
adjustment step.
A/O
Example:
FullMax(ul-config)# set down-power-offset-adj-step 6
Full Spectrum Confidential
36
FullMax BS100 and MS400 User Manual Version 1.1
Updated down-power-offset-adj-step 6 (in 0.01 dB).
FullMax(ul-config)# show up-power-offset-adj-step
up-power-offset-adj-step 6 (in 0.01 dB).
min-power-offset-adj
Minimum level of power offset adjustment.
Command
FullMax(ul-config)# set
min-power-offset-adj 
Purpose
The command allows the user to update
the value of Minimum level of power
offset adjustment.
The command allows the user to display
the value of Minimum level of power
offset adjustment.
FullMax(ul-config)#show
min-power-offset-adj
Privileges
A/O
Example:
FullMax(ul-config)# set min-power-offset-adj 2
Updated min-power-offset-adj 2 (in 0.01 dB).
FullMax(ul-config)# show min-power-offset-adj
min-power-offset-adj 2 (in 0.01 dB).
maxmax-powerpower-offsetoffset-adj
Maximum level of power offset adjustment.
Command
FullMax(ul-config)#set
max-power-offset-adj

FullMax(ul-config)#show
max-power-offset-adj
Purpose
The command allows the user to update the
value of maximum level of power offset
adjustment.
Privileges
The command allows the user to display the
value of maximum level of power offset
adjustment.
A/O
Example:
FullMax (ul-config) # set max-power-offset-adj 16
Updated max-power-offset-adj 16 (in 0.01 dB).
FullMax (ul-config) # show max-power-offset-adj
max-power-offset-adj 16 (in 0.01 dB).
initialinitial-rngrng-backoffbackoff-start
Initial backoff window size for initial ranging connection, expressed as a power of 2.
Command
FullMax(ul-config)# set
intial-rng-backoff-start
Purpose
The command allows the user to update
the value of initial backoff window size
for initial ranging connection.
Full Spectrum Confidential
37
Privileges
FullMax BS100 and MS400 User Manual Version 1.1

FullMax(ul-config)#show
intial-rng-backoff-start
The command allows the user to display
the value of initial backoff window size
for initial ranging connection.
A/O
Example:
FullMax(ul-config)# set intial-rng-backoff-start 2
Updated intial-rng-backoff-start 2
FullMax(ul-config)# show intial-rng-backoff-start
intial-rng-backoff-start 2
initialinitial-rngrng-backoffbackoff-end
Final backoff window size for initial ranging connection, expressed as a power of 2.
Command
FullMax(ul-config)# set
intial-rng-backoff-end

FullMax(ul-config)# show
intial-rng-backoff-end
Purpose
The command allows the user to update
the value of final backoff window size
for initial ranging connection.
Privileges
The command allows the user to display
the value of final backoff window size
for initial ranging connection.
A/O
Example:
FullMax(ul-config)# set intial-rng-backoff-end 8
Updated intial-rng-backoff-end 8
FullMax(ul-config)# show intial-rng-backoff-end
intial-rng-backoff-end 8
bwbw-reqreq-backoffbackoff-start
Initial backoff window size for contention bandwidth requests, expressed as a power of 2.
Command
FullMax(ul-config)# set
bw-req-backoff-start 
FullMax(ul-config)#show
bw-req-backoff-start
Purpose
The command allows the user to update
the value of initial backoff window size
for contention bandwidth requests.
The command allows the user to display
the value of initial backoff window size
for contention bandwidth requests.
Full Spectrum Confidential
Privileges
A/O
38
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(ul-config)#set bw-req-backoff-start 4
Updated bw-req-backoff-start 4
FullMax(ul-config)#show bw-req-backoff-start
bw-req-backoff-start 4
bwbw-reqreq-backoffbackoff-end
Final backoff window size for contention bandwidth requests, expressed as a power of 2.
Command
FullMax(ul-config)# set
bw-req-backoff-end 
FullMax(ul-config)# show
bw-req-backoff-end
Purpose
The command allows the user to update the
value of final backoff window size for
contention bandwidth requests.
The command allows the user to display the
value of final backoff window size for
contention bandwidth requests.
Privileges
A/O
Example:
FullMax(ul-config)# set bw-req-backoff-end 8
Updated bw-req-backoff-end 4
FullMax(ul-config)# show bw-req-backoff-end
bw-req-backoff-end 4
all
This command displays all the parameter values of tables supported in this group.
Command
FullMax(ul-config)#
show all
Purpose
The command allows the user to display the
value of all the MIB parameters of tables
supported in this group.
Privileges
A/O
Example:
FullMax(ul-config)# show all
ct-based-reserve-timeout 200
uplink-center-frequency 200
init-rng-codes 0
periodic-rng-codes 50
bandwidth-request-codes 0
per-rng-backoff-start 20
permutation-base 0
ul-alloc-sub-channel-bitmap 3
band-amc-alloc-threshold 60 db
band-amc-release-threshold 0 db
Full Spectrum Confidential
39
FullMax BS100 and MS400 User Manual Version 1.1
band-amc-alloc-timer 255 Frames
band-amc-release-timer 0 Frames
5.2.4 dl-config
The group defines the commands that monitors or updates the DCD channel attributes
that define the characteristics of downlink channel. The user upon entering the dl-config
command locks into the CLI to execute commands only related to BS downlink channel
characteristics.
FullMax#
FullMax# dl-config
FullMax(dl-config)#
Command
FullMax# dl-config
Purpose
Privileges
The command allows the user to lock
A/O
into the group dl-config and execute
all the commands related to the group.
dldl-channelchannel-table
This command Displays the values of all the commands affiliated to dl-channel-table in
the dl-config group.
Command
FullMax(dl-config)#show
dl-channel-table
Purpose
The command allows the user to display
the DL Channel table MIB parameter
values.
Privileges
A/O
Example:
FullMax(dl-config)# show dl-channel-table
bs-eirp 244 dBm
downlink-center-frequency 244 khz
bsid 00f401:0000f4
hysterisis-margin 45 dB
time-to-trigger 2 milliseconds
frameframe-durationduration-code
The duration of the frame
Command
FullMax(dl-config)#set
frame-duration-code
FullMax(dl-config)#show
frame-duration-code
Purpose
The command allows the user to update
the OFDMA frame duration code.
The command allows the user to display
the OFDMA frame duration code.
Full Spectrum Confidential
Privileges
A/O
40
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(dl-config)# set frame-duration-code 12
updated frame-duration-code 12
FullMax(dl-config)# show frame-duration-code
frame-duration-code 12
bsbs-eirp
The EIRP is the equivalent isotropic radiated power of the base station, which computed
for a simple single-antenna transmitter.
Command
FullMax(dl-config)#set
bs-eirp 
FullMax(dl-config)#show
bs-eirp
Purpose
The command allows the user to update
the BS EIRP parameter
Privileges
The command allows the user to display
the BS EIRP parameter
A/O
Example:
FullMax(dl-config)# set bs-eirp 3770
Updated bs-eirp 3770 dBm
FullMax(dl-config)# show bs-eirp
bs-eirp 3770 dBm
downlinkdownlink-centercenter-frequency
Downlink center frequency (Khz).
Command
FullMax(dl-config)# set
downlink-center-frequency

FullMax(dl-config)#show
downlink-center-frequency
Purpose
Privileges
The command allows the user to update the A
downlink center frequency.
The command allows the user to display
the downlink center frequency.
A/O
Example:
FullMax (dl-config)# set downlink-center-frequency
11000
Updated downlink-center-frequency 11000 kHz
FullMax(dl-config)# show downlink-center-frequency
downlink-center-frequency 11000 kHz.
Full Spectrum Confidential
41
FullMax BS100 and MS400 User Manual Version 1.1
bsid
Defines the encoding of BSID. The BSID is a 6 byte number and follows the encoding
rules of MacAddress textual convention, e.e as if it were transmitted least-significant bit
first. The value should be displayed with 2 parts clearly separated by a colon e.g :
001DFF:00003A. The most significant part is representing the operator ID.
Command
FullMax(dl-config)# set
bsid 
FullMax(dl-config)#show
bsid
Purpose
The command allows the user to update the
BS ID
Privileges
The command allows the user to display the
BS ID
A/O
Example:
FullMax(dl-config)# set bsid 0A30A1:10FE11
Updated bsid 0A30A1:10FE11
FullMax(dl-config)# show bsid
bsid 0A30A1:10FE11
bandwidth
Channel Bandwidth in Khz
Command
FullMax(dl-config)# set
bandwidth 
FullMax(dl-config)#show
bandwidth
Purpose
Privileges
The command allows the user to updates the A
channel bandwidth.
The command allows the user to display the
channel bandwidh.
A/O
Example:
FullMax(dl-config)# set bandwidth 400
Updated bandwidth 400 KHz
FullMax(dl-config)# show bandwidth
bandwidth 400 KHz
SamplingSampling-clock
Sampling clock for the channel
Command
FullMax(dl-config)#set
sampling-clock 
FullMax(dl-config)#show
sampling-clock
Purpose
The command allows the user to updates the
sampling clock.
Privileges
The command allows the user to display the
sampling clock.
A/O
Full Spectrum Confidential
42
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(dl-config)# set sampling-clock 12800
Updated sampling-clock 12800 KHz
FullMax(dl-config)# show sampling-clock
sampling-clock 12800 KHz
filterfilter-id
The ID of the PHY filter to use for this channel
Command
FullMax(dl-config)# set
filter-id 
Purpose
The command allows the user to updates
the filter id.
Privileges
FullMax(dl-config)#show
filter-id
The command allows the user to display
the filter id.
A./O
Example:
FullMax(dl-config)# set filter-id 1
Updated filter-id 1
FullMax(dl-config)# show filter-id
filter-id 1
fft_size
FFT size for OFDMA PHY
Command
FullMax(dl-config)# set
fft_size 
FullMax(dl-config)#show
fft_size
Purpose
The command allows the user to
updates the fft_size.
The command allows the user to display the
fft_size
Privileges
A/O
Example:
FullMax (dl-config)# set fft_size 512
Updated fft_size 512
FullMax (dl-config) # show fft_size
fft_size 512
dl_framedl_frame-duration
This field indicates the number of OFDMA symbols allocated for downlink transmission
in the OFDMA frame
Command
FullMax(dl-config)# set
dl_frame-duration 
Purpose
The command allows the user to
updates the downlink frame duration
Full Spectrum Confidential
Privileges
43
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(dl-config)# show
dl_frame-duration
The command allows the user to
display the downlink frame duration
A/O
Example:
FullMax (dl-config)# set dl_frame-duration 20
Updated dl_frame-duration 20 ofdma symbols
FullMax (dl-config) # show dl_frame-duration
dl_frame-duration 20 ofdma symbols
ul_frameul_frame-duration
This field indicates the number of OFDMA symbols allocated for uplink transmission in
the OFDMA frame.
Command
FullMax(dl-config)# set
ul_frame-duration 
FullMax(dl-config)#show
ul_frame-duration
Purpose
Privileges
The command allows the user to updates A
the uplink frame duration.
The command allows the user to display
the uplink frame duration.
A/O
Example:
FullMax (dl-config)# set ul_frame-duration 10
Updated ul_frame-duration 10 ofdma symbols
FullMax (dl-config) # show ul_frame-duration
ul_frame-duration 10 ofdma symbols
dl_zones_num
Number of downlink zones for the BS
Command
FullMax(dl-config)#set
dl_zones_num 
FullMax(dl-config)#show
dl_zones_num
Purpose
Privileges
The command allows the user to update A
the number of downlink zones.
The command allows the user to
display the number of downlink zones.
A/O
Example:
FullMax (dl-config)# set dl_zones_num 2
Updated dl_zones_num 2 zones
FullMax (dl-config) # show dl_zones_num
dl_zones_num 2 zones
Full Spectrum Confidential
44
FullMax BS100 and MS400 User Manual Version 1.1
ul_zones_num
Number of uplink zones for the BS
Command
FullMax(dl-config)# set
ul_zones_num 
Purpose
The command allows the user to
updates the number of uplink
zones
The command allows the user to
display the number of uplink zones.
FullMax(dl-config)#show
ul_zones_num
Privileges
A/O
Example:
FullMax(dl-config)# set ul_zones_num 2
Updated ul_zones_num 2 zones
FullMax (dl-config)# show ul_zones_num
ul_zones_num 2 zones
5.2.5 zone-config
The group defines the commands that monitors or updates the downlink and uplink zones
attributes. The user upon entering the zone-config command locks into the CLI to execute
commands only related to BS downlink and uplink zones characteristics.
FullMax#
FullMax# zone-config
FullMax(zone-config)#
Command
FullMax# zone-config
Purpose
The command allows the user to lock into
the group zone-config and execute all
the commands related to the group.
Privileges
A/O
dldl-zonezone-id
The downlink zone identifier ,the index of the first zone will always be 0
Command
FullMax(zone-config)#show
dl-zone-id
Purpose
The command allows the user to
display the avaliable DL zone ids.
Privileges
A/O
Example:
FullMax(zone-config)#show dl-zone-id
dl-zone-id 0
dl-zone-id 1
Full Spectrum Confidential
45
FullMax BS100 and MS400 User Manual Version 1.1
dl-zone-id 2
dldl-zonezone-table
This table contains zone attributes that characterize a downlink zone
Command
FullMax(zone-config)#
show dl_zone-table
Purpose
The command allows the user to display the
list of downlink zones.
FullMax(zone-config)# show dl-zone-table
dl-zone-stc 0
dl-perm-type pusc
dl-perm-base 17
dl-start-symbol 11
dl-all-sc YES
dl-cinr-threshold 2 dB
Privileges
A/O
dldl-permperm-type
Permutation type of this zone
Command
FullMax(zone-config)# set
dl-perm-type  
FullMax(zone-config)# show
dl-perm-type 
Purpose
The command allows the user to
update the downlink permutation
type of zone 
The command allows the user to
display the permutation type of
zone 
Privileges
A/O
Example:
FullMax(zone-config)# set dl-perm-type 0 1
Updated dl-perm-type of zone 0 to pusc (1)
FullMax(zone-config)# show dl-perm-type 0
dl-perm-type of zone 0 is pusc (2)
dldl-zonezone-stc
Downlink zone
Command
FullMax(zone-config)# set
dl-perm-zone 

FullMax(zone-config)#show
Purpose
The command allows the user to
update the downlink permutation
zone of zone 
The command allows the user to
Full Spectrum Confidential
Privileges
A/O
46
FullMax BS100 and MS400 User Manual Version 1.1
dl-perm-zone 
display the permutation zone of zone

Example:
FullMax(zone-config)# set dl-zone-stc 0 2
Updated dl-zone-stc of zone 0 to nonstc (2)
FullMax(zone-config)# show dl-zone-stc 0
dl-zone-stc of zone 0 is nonstc (2)
dldl-permperm-base
Permutation base for this zone
Command
FullMax(zone-config)#
set dl-perm-base 

FullMax(zone-config)#
show dl-perm-base 
Purpose
Privileges
The command allows the user to update the A
downlink permutation base of zone 
The command allows the user to display
the permutation base of zone 
A/O
Example:
FullMax(zone-config)# set dl-perm-base 0 17
Updated dl-perm-base of zone 0 to 17
FullMax(zone-config)# show dl-perm-base
dl-perm-base of zone 0 is 17
dldl-startstart-symbol
Index of the starting symbol for this zone.
Command
FullMax(zone-config)# set
dl-start-symbol 

FullMax(zone-config)#show
dl-start-symbol 
Purpose
The command allows the user to update
the start-symbol downlink of 
Privileges
The command allows the user to display
the start-symbol of 
A/O
Example:
FullMax (zone-config)# set dl-start-symbol 0 5
Updated dl-perm-type of zone 0 to 5
FullMax(zone-config)# show dl-start-symbol
dl-start-symbol of zone 0 is 5
dldl-allall-sc
Full Spectrum Confidential
47
FullMax BS100 and MS400 User Manual Version 1.1
Use all subchannels.
1 (true): use_all_SC=1
2 (false): use_all_SC=0
Downlink zone parameters –
Command
FullMax (zone-config)#set
dl-all-sc  
FullMax(zone-config)#show
dl-all-sc 
Purpose
The command allows the user to
update the downlink zone–allsubchannels parameter
The command allows the user to
display the all subchannels parameter
of 
Privileges
A/O
Example:
FullMax(zone-config)# set dl-all-sc 0 YES
Updated dl-all-sc of zone 0 to YES
FullMax (zone-config) # show dl-all-sc 0
dl-all-sc of zone 0 is YES
dldl-cinrcinr-threshold
Threshold of the maximum of the standard deviations of the individual bands CINR
measurements over time to trigger mode transition from zone 0 to this zone.
Command
FullMax(zone-config)# set
dl-cinr-threshold 

FullMax(zone-config)#show
dl-cinr-threshold 
Purpose
Privileges
The command allows the user to update A
the CINR threshold for 
The command allows the user to
display the CINR threshold for 
A/O
Example:
FullMax(zone-config)# set dl- cinr-threshold 0 2
Updated dl-cinr-threshold of zone 0 to 2 dB
FullMax(zone-config)# show dl-cinr-threshold 0
dl-cinr-threshold of zone 0 is 2 dB
ulul-ZoneZone-id
The uplink zone identifier , The index of the first uplink zone will always be 0
Command
FullMax(zone-config)# show
ul-zone-id
Purpose
The command allows the user to display
the ul zone indixes avaliable
Full Spectrum Confidential
Privileges
A/O
48
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(zone-config)#show ul-zone-id
ul-zone-id 0
ul-zone-id 1
ul-zone-id 2
ul-zone-table
Displays the Uplink zones table
Command
FullMax(zone-config)#show
ul_zone-table
Purpose
The command allows the user to
display the list of uplink zones.
Privileges
A/O
Example:
FullMax(zone-config)# show ul-zone-table 0
ul-perm-type for zone-id (0) : nonstc(2)
ul-perm-base for zone-id (0) : 17
ul-start-symbol for zone-id (0) : 11
ul-alloc-bitmap for zone-id (0) : 3
ul-cinr-threshold for zone-id (0) : 2 dB
ul-perm-type
A zone permutation type
Command
FullMax(zone-config)#set
ul-perm-type  
FullMax(zone-config)#show
ul-perm-type 
Purpose
The command allows the user to
update the uplink permutation type of

The command allows the user to
display the permutation type of zone

Privileges
A/O
Example:
FullMax(zone-config)# set ul-perm-type 0 2
Updated ul-perm-type for zone-id(0): to non-stc (2)
FullMax(zone-config)# show ul-perm-type 0
ul-perm-type for zone-id (0) : non-stc (2)
ul-perm-base
Determines the Permutation Base parameter for the zone, permutation to be used on this
uplink zone
Command
Purpose
Full Spectrum Confidential
Privileges
49
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(zone-config)# set
ul-perm-base  
FullMax(zone-config)#show
ul-perm-base 
The command allows the user to
update the uplink permutation base of

The command allows the user to
A/O
display the permutation base of

Example:
FullMax(zone-config)# set ul-perm-base 0 17
Updated ul-perm-base for zone-id (0) to 17
FullMax (zone-config) # show ul-perm-base
ul-perm-base for zone-id (0) : 17
ul-start-symbol
Index of the starting symbol for this zonehat segment
Command
FullMax(zone-config)# set
ul-start-symbol 

FullMax(zone-config)# show
ul-start-symbol 
Purpose
The command allows the user to
update the start-symbol uplink of

The command allows the user to
display the start-symbol of 
Privileges
A/O
Example:
FullMax (zone-config)# set ul-start-symbol 0 5
Updated ul-start-symbol for zone-id (0) to 5
FullMax (zone-config) # show ul-start-symbol
ul-start-symbol for-id zone-id(0) :5
ul-alloc-bitmap
This is a bitmap describing the physical sub-channels allocated to the segment in the UL,
when using the uplink PUSC permutation. The LSB of the first byte shall corrspond to
subchannel 0. For any bit that is not set, the corresponding subchannel shall not be used
by the SS on that segment
Command
FullMax(zone-config)# set
ul-alloc-bitmap 

FullMax(zone-config)#show
ul-alloc-bitmap 
Purpose
The command allows the user to
update the uplink zone – allocation
bitmap parameter
The command allows the user to
display the allocation bitmap
parameter of zone 
Privileges
A/O
Example:
Full Spectrum Confidential
50
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(zone-config)# set ul-alloc-bitmap 0 010101
Updated ul-alloc-bitmap for zone-id (0) : to 010101
FullMax(zone-config) # show ul-alloc-bitmap 0
ul-alloc-bitmap of zone-id (0) : 01010101
ul-cinr-threshold
This object is used to ensure that the write operation to multiple columns is guaranteed to
be treated as atomic operation by agent.
Command
FullMax(zone-config)# set
ul-cinr-threshold 

FullMax(zone-config)# show
ul-cinr-threshold 
Purpose
The command allows the user to
update the CINR threshold for
zone 
The command allows the user to
display the CINR threshold for
zone 
Privileges
A/O
Example:
FullMax(zone-config)# set ul-cinr-threshold 0 2
Updated ul-cinr-threshold for zone-id (0) to 2 dB
FullMax(zone-config)# show ul-cinr-threshold 0
ul-cinr-threshold for zone-id (0): 2 dB
5.2.6 bs-cap-config
The group defines the commands to configure the basic capabilities of BS. The user
upon entering the bs-capability-config command locks into the CLI to execute commands
only related to basic capabilities of BS.
FullMax#
FullMax# bs-cap-config
FullMax(bs-cap-config)#
Command
FullMax# bs-cap-config
all
Purpose
The command allows the user to lock into
the group bs-cap-config and execute all the
commands related to the group.
Privileges
A/O
Description
Command
FullMax(bs-cap-
Purpose
The command allows the user to
Full Spectrum Confidential
Privileges
A/O
51
FullMax BS100 and MS400 User Manual Version 1.1
onfig)#show all
display values of all the attributes of
bs-cap-config group
Example:
FullMax(bs-cap-config)# show all
capability-ttg-transition-gap 34 microseconds
capability-rtg-transition-gap 34 microseconds
capability-pn-window-size 1000
capability-number-of-ul-harq-channel 0
capability-number-of-dl-harq-channel 0
Capability-ttg-transition-gap
This parameter indicates the configured transition speed SSTTG for TDD and H-FDD
SSs. The usage is defined by ss-transistion-gap
Command
FullMax(bs-cap-config)# set
capability-ttg-transitio-gap

FullMax(bs-cap-config)# show
capability-ttg-transitio-gap
Purpose
The command allows the user to
update the TTG transition gap
parameter
Privileges
The command allows the user to
display the TTG transition gap
parameter
A/O
Example:
FullMax(bs-cap-config)# set capability-ttg-transitio-gap

Updated capability-ttg-transitio-gap
FullMax(bs-cap-config)# show capability-ttg-transitio-gap
capability-ttg-transitio-gap
Capability-rtg-transition-gap
This parameter indicates the configured transition speed SSTTG for TDD and H-FDD
SSs. The usage is defined by ss-transition-gap.
Command
FullMax(bs-cap-config)# set
capability-rtg-transition-gap

Purpose
The command allows the user to
update the RTG transition gap.
Full Spectrum Confidential
Privileges
52
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(bs-cap-config)#show
capability-rtg-transition-gap
The command allows the user to
display the RTG transition gap.
A/O
Example:
FullMax(bs-cap-config)# set capability-rtg-transition-gap
30
Updated capability-rtg-transition-gap
FullMax (bs-cap-config)# show capability-rtg-transitiongap
capability-rtg-transition-gap 30
5.2.7 bs-burst-profile
The group defines the commands to burst profile commands of BS. The user upon
entering the bs-burst-profile command locks into the CLI to execute commands only
related to BS burst profile of BS.
FullMax#
FullMax# bs-burst-profile
FullMax(bs-burst-profile)#
Command
FullMax#bs-burst-profile
uiuc-index
Purpose
The command allows the user to lock
into the group bs-burst-profile and
execute all the commands related to the
group.
Privileges
A/O
The uplink interval usage code inidicates the uplink burst profile in the ucd message and
is used along the index to identify the ucd-fec-code. Max uiuc -index range for OFDMA
PHY <0- 10 >
Command
FullMax(bs-burst-Profile)#
show uiuc-index
Purpose
The command allows the user to
display the Uplink intetrval usage
codes indexes avaliable in the MAC
Privileges
A/O
Example:
FullMax(bs-burst-profile)# show uiuc-index
uiuc-index 0
uiuc-index 1
uiuc-index 2
uiuc-index 3
Full Spectrum Confidential
53
FullMax BS100 and MS400 User Manual Version 1.1
ucd-fec-code-type
Uplink FEC code type and modulation type
Command
FullMax (bs-burst-rofile)#
show dcd-fec-code-type

Purpose
The command allows the user to
display the different FEC and coding
options for uplink burst profile.
Privileges
A/O
Example:
FullMax(bs-burst-profile)# show ucd-fec-code-type 1
ucd-fec-code-type for uiuc-index (1) :
qpskCc1Over2(0), qpskCc3Over4(1),
sixteenQamCc1Over2(2), sixteenQamCc3Over4(3),
sixtyFourQamCc1Over2(4), sixtyFourQamCc2Over3(5),
sixtyFourQamCc3Over4(6), qpskBtc1Over2(7),
qpskBtc3Over4Or2Over3(8), sixteenQamBtc3Over5(9),
sixteenQamBtc4Over5(10),
sixtyFourQamBtc2Over3Or5Over8(11),
sixtyFourQamBtc5Over6Or4Over5(12), qpskCtc1Over2(13),
reserved14(14), qpskCtc3Over4(15),
sixteenQamCtc1Over2(16), sixteenQamCtc3Over4(17),
sixtyFourQamCtc1Over2(18), sixtyFourQamCtc2Over3(19),
sixtyFourQamCtc3Over4(20), sixtyFourQamCtc5Over6(21),
qpskZtCc1Over2(22), qpskZtCc3Over4(23),
sixteenQamZtCc1Over2(24), sixteenQamZtCc3Over4(25),
sixtyFourQamZtCc1Over2(26),
sixtyFourQamZtCc2Over3(27),
sixtyFourQamZtCc3Over4(28), qpskLdpc1over2(29),
qpskLdpc2over3A(30), qpskLdpc3over4A(31),
sixteenQamLdpc1over2(32), sixteenQamLdpc2over3A(33),
sixteenQamLdpc3over4A(34), sixtyFourQamLdpc1over2(35),
sixtyFourQamLdpc2over3A(36),
sixtyFourQamLdpc3over4A(37), qpskLdpc2over3B(38),
qpskLdpc3over4B(39), sixteenQamLdpc2over3B(40),
sixteenQamLdpc3over4B(41),
sixtyFourQamLdpc2over3B(42),
sixtyFourQamLdpc3over4B(43), qpskCcOptIntv1over2(44),
qpskCcOptIntv3over4(45),
sixteenQamCcOptIntv1over2(46),
sixteenQamCcOptIntv3over4(47),
sixtyFourQamCcOptIntv2over3(48),
sixtyFourQamCcOptIntv3over4(49), qpskLdpc5over6(50),
sixteenQamLdpc5over6(51), sixtyFourQamLdpc5over6(52)
diuc-index
Full Spectrum Confidential
54
FullMax BS100 and MS400 User Manual Version 1.1
The Downlink interval usage code inidicates the uplink burst profile in the ucd message
and is used along the index to identify the Dcd-fec-code. Max diuc -index range for
OFDMA PHY <0- 12 >
Command
FullMax(bs-burst-Profile)#
show diuc-index
Purpose
The command allows the user to
display the Downlink interval
usage codes indexes avaliable in
the MAC
Privileges
A/O
Example:
FullMax(bs-burst-profile)# show diuc index
diuc-index 0
diuc-index 1
diuc-index 2
diuc-index 3
dcd-fec-code-type
Displays FEC and coding options for downlink burst profiles
Command
FullMax (bs-burstprofile)# show dcdfec-code-type 
Purpose
The command allows the user to display
the different FEC and coding options for
downlink burst profile.
Privileges
A/O
Example:
FullMax (bs-burst-profile) # show dcd-fec-code-type 2
dcd-fec-code-type for dicu-index (2) is
qpskCc1Over2(0), qpskCc3Over4(1),
sixteenQamCc1Over2(2), sixteenQamCc3Over4(3),
sixtyFourQamCc1Over2(4), sixtyFourQamCc2Over3(5),
sixtyFourQamCc3Over4(6), qpskBtc1Over2(7),
qpskBtc3Over4Or2Over3(8), sixteenQamBtc3Over5(9),
sixteenQamBtc4Over5(10),
sixtyFourQamBtc2Over3Or5Over8(11),
sixtyFourQamBtc5Over6Or4Over5(12), qpskCtc1Over2(13),
reserved14(14), qpskCtc3Over4(15),
sixteenQamCtc1Over2(16), sixteenQamCtc3Over4(17),
sixtyFourQamCtc1Over2(18), sixtyFourQamCtc2Over3(19),
sixtyFourQamCtc3Over4(20), sixtyFourQamCtc5Over6(21),
qpskZtCc1Over2(22), qpskZtCc3Over4(23),
sixteenQamZtCc1Over2(24), sixteenQamZtCc3Over4(25),
sixtyFourQamZtCc1Over2(26),
sixtyFourQamZtCc2Over3(27),
Full Spectrum Confidential
55
FullMax BS100 and MS400 User Manual Version 1.1
sixtyFourQamZtCc3Over4(28), qpskLdpc1over2(29),
qpskLdpc2over3A(30), qpskLdpc3over4A(31),
sixteenQamLdpc1over2(32), sixteenQamLdpc2over3A(33),
sixteenQamLdpc3over4A(34), sixtyFourQamLdpc1over2(35),
sixtyFourQamLdpc2over3A(36),
sixtyFourQamLdpc3over4A(37), qpskLdpc2over3B(38),
qpskLdpc3over4B(39), sixteenQamLdpc2over3B(40),
sixteenQamLdpc3over4B(41),
sixtyFourQamLdpc2over3B(42),
sixtyFourQamLdpc3over4B(43), qpskCcOptIntv1over2(44),
qpskCcOptIntv3over4(45),
sixteenQamCcOptIntv1over2(46),
sixteenQamCcOptIntv3over4(47),
sixtyFourQamCcOptIntv2over3(48),
sixtyFourQamCcOptIntv3over4(49), qpskLdpc5over6(50),
sixteenQamLdpc5over6(51), sixtyFourQamLdpc5over6(52)
5.2.8 bs-ss-action
The bs-ss-action group define the commands that monitors or updates the actions
specified for SS. The user upon entering the bs-ss-action command locks into the CLI to
execute commands only related to BS private mib.
FullMax#
FullMax#bs-ss-action
FullMax(bs-ss-action)#
Command
FullMax#bs-ss-action
reset-ss
Purpose
The command allows the user to lock into
the group bs-ss-action and execute all the
commands related to the group.
Privileges
A/O
Reset action performed on SS.
Command
FullMax(bs-ss-action)#set
reset-ss 
Purpose
The command allows the user to
perform reset action on SS
Privileges
Example:
FullMax(bs-ss-action)# set reset-ss 1 0A1234:5678AB
Reset-ss message sent to 0A1234:5678AB
abort-ss
Abort action performed on SS.
Full Spectrum Confidential
56
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(bs-ss-action)#set
abort-ss   [-d:dl-freq] [u:up-id]
Purpose
The command allows the user
to perform the abort action on
SS
Privileges
A/O
FullMax(bs-ss-action)# set abort-ss 1 
abort-ss message sent to 
FullMax(bs-ss-action)# set abort-ss 2 0A1234:5678AB
-d:210000
abort-ss message with downlink frequency override
210000 KHz sent to 0A1234:5678AB
de-reg-ss
De-registration action on SS
Command
FullMax(bs-ss-action)#
set abort-ss   [d:dl-freq] [-u:up-id]
FullMax(bs-ss-action)#
reg-ss message sent to
transmission code (2)
FullMax(bs-ss-action)#
De-reg-ss message
transmission code (1)
Purpose
The command allows the user to perform
the abort action on SS
set de-reg-ss 0A1234:5678AB 2
0A1234:5678AB with limited
Privileges
A/O
De-
set de-reg-ss 0A1234:5678AB 1
sent to 0A1234:5678AB with no
5.2.9 ss-registered
The ss-registered group defines the commands that monitors or updates the standard mib
related information. The user upon entering the ss-registered command locks into the CLI
to execute commands only related to SS registered table mib.
FullMax#
FullMax# ss-registered
FullMax ss-registered)#
Command
FullMax# ss-registered
Purpose
The command allows the user to lock
into the group ss-registered and execute
all the commands related to the group.
Full Spectrum Confidential
Privileges
A/O
57
FullMax BS100 and MS400 User Manual Version 1.1
ss-mac-addresss
The MAC address of SS is received in the RNG-REQ message when SS registers ,this
MAC address is entered in to the Bs Registered Ss Table.
Command
FullMax(ssregistered)# show
registered-ss-macaddress
Purpose
The command allows the user
display all the SS MAC addresses.
Privileges
A/O
Example:
FullMax(ss-registered)# show registered-ss-mac-address
Registered SS MAC Addresses are:
registered-ss-mac-address 1 001BFE:01020A
registered-ss-mac-address 2 001BAA:01030F
registered-ss-mac-address 3 001BEF:01F01A
max-tx-power-qpsk
SS’s Maximum available power for QPSK in dBm. This parameter is only applicable to
systems supporting the SCa, OFDM or OFDMA PHY.
Command
FullMax(ss-registered)#
show max-tx-power-qpsk

Purpose
The command allows the user
display SS’s Maximum available
power for QPSK in dBm. Here key
is SS’s MAC address.
Privileges
A/O
Example:
FullMax(ss-registered)# show max-tx-power-qpsk
001BFE:01020A
max-tx-power-qpsk 27 dBm
max-tx-power-16qam
SS’s Maximum available power for 16-QAM constellations in dBm. This parameter is
only applicable to systems supporting the SCa, OFDM or OFDMA PHY.
Command
FullMax(ssregistered)# show maxtx-power-16qam 
Purpose
The command allows the user
display SS’s Maximum available
power for 16QAM in dBm. Here
key is SS’s MAC address.
Privileges
A/O
Example:
Full Spectrum Confidential
58
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(ss-registered)# show max-tx-power-16qam
001BAA:01030F
max-tx-power-16qam 20 dBm
max-tx-power-64qam
SS’s Maximum available power for 64-QAM constellations in dBm. This parameter is
only applicable to systems supporting the SCa, OFDM or OFDMA PHY.
Command
FullMax(ssregistered)# show maxtx-power-64qam 
Purpose
The command allows the user
display SS’s Maximum available
power for 64QAM in dBm. Here
key is SS’s MAC address.
Privileges
A/O
Example:
FullMax(ss-registered)# show max-tx-power-64qam
001BEF:01F01A
max-tx-power-64qam 25 dBm
5.2.10
ss-ip
The bs-ss-ip group define the commands that monitors or updates the BsSsIp related
information. The user upon entering the ss-ip command locks into the CLI to execute
commands only related to BsSsIpTable defined in the private mib.
FullMax#
FullMax# ss-ip
FullMax(ss-ip)#
Command
FullMax# ss-ip
Purpose
The command allows the user to lock into the
group ss-ip and execute all the commands
related to the group.
Privileges
A/O
ss-ip-table
This table contains the IP configuration information of Subcriber station's as set by
DHCP Relay function in the Base Station.
Command
FullMax(ss-ip)#show
ss-ip-table
Purpose
The command allows the user display the
MS IP table.
Privileges
A/O
Example:
FullMax (bs-private) # show ss-ip-table 001BFE:01020A
ss-mac-address 001BFE:01020A
Full Spectrum Confidential
59
FullMax BS100 and MS400 User Manual Version 1.1
ss-ip-address 192.168.0.1
ss-subnet-mask 192.168.0.0
ss-mac-address
The MAC address of SS is received from the RNG-REQ message. When SS registers,
this MAC address is entered into the table, and used as the identifier to the SS.
Command
FullMax (ss-ip) #
show ss-mac-address
Purpose
The command allows the user
display the MS MAC address
of all MS.
Privileges
A/O
Example:
FullMax (ss-ip) # show ss-mac-address
ss-mac-addres 00A1B3:01AB03
ss-mac-addres 00A1B3:010203
ss-mac-addres 00A1B3:010405
ss-ip-address
The subnet mask address of SS as received from BS DHCP Relay. When SS Registers,
this IP address is entered into the table, and used as the identifier to the SS.
Command
FullMax (ss-ip) #
show ss-ip-address
Purpose
The command allows the user
display the IP address.
Privileges
A/O
Example:
FullMax(ss-ip)# show ss-ip-address 00A1B3:01AB03
ss-ip-addres 192.168.0.1
ss-subnet-mask
The IP address of SS is received from the DHCP-Relay in the BS when SS register, this
IP address is entered into the table, and used as the identifier to the SS.
Command
FullMax(ss-ip)#show
ss-ip-address
Purpose
The command allows the user display the
subnet mask of all the MS.
Privileges
A/O
Example:
FullMax(ss-ip)# show ss-subnet-mask 00A1B3:01AB03
ss-subnet-mask 192.168.0.0
Full Spectrum Confidential
60
FullMax BS100 and MS400 User Manual Version 1.1
5.2.11
device
The device group define the commands that monitors or
updates the device related information in the private MIB.
The user upon entering the device command locks into the
CLI to execute commands only related to device.
FullMax#
FullMax# device
FullMax(device)#
Command
FullMax# device
Purpose
The command allows the user to lock into the
group device and execute all the commands
related to the group.
Privileges
A/O
Purpose
The command allows the user display the
device type (BS/MS/SS)
Privileges
A/O
type
Type of device (BS/MS/SS).
Command
FullMax(device)
# show type
Example:
FullMax(device)# show type
type BS
gpos
The geographical position of the device ,
i.e. the real number describing the longitude and latitusde encoded as a printable string.
Longitude - the precision is within the range -90..90 degrees.Positive numbers indicate
locations north of the equator.
Latitude - The precision is within the range -180..180 degrees.Positive numbers indicate
locations east of the prime meridian
Command
FullMax(device)# set
gpos 
FullMax(device)#
show gpos
Example:
Purpose
The command allows the user to update the
geographical position of the device
The command allows the user display
geographical position of the device.
Privileges
A/O
FullMax(device)# set gpos 64.000 88.3400
updated gpos 64.000 88.3400
Full Spectrum Confidential
61
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(device) # show gpos
gpos 64.000 88.3400
boot-time
The absolute time of last device boot up.
Command
FullMax(device)#
show boot-time
Purpose
The command allows the user display the
device boot up time.
Privileges
A/O
Example:
FullMax(device)# show boot-time
boot-time 230404:18052008
commit-save
Setting this object to TRUE causes the device to write all configuration changes in
FLASH memory. On next boot the changes will be relevant. If this operation does not
occur, configuration changes will not be maintained through reset Reading this object
always returns FALSE
Command
FullMax(device)# set
commit-save 
Purpose
The command allows the user update
the commit-save to TRUE .
Privileges
FullMax(device)# show
commit-save
The command allows the user display A/O
the commit-save
Example:
FullMax(device)# set commit-save TRUE
Updated commit-save TRUE
FullMax(device)# show commit-save
commit-save FALSE
gps-card
GPS card availability in the device.
Command
FullMax(device)#sho
w gps-card
Purpose
The command allows the user display
the availability of GPS card in the
device.
Privileges
A/O
Example:
FullMax(device)# show gps-card
gps-card YES
Full Spectrum Confidential
62
FullMax BS100 and MS400 User Manual Version 1.1
bpc-hw-version
Hardware version of baseband processor card.
Command
FullMax(device)#show
bpc-hw-version
Purpose
The command allows the user display the
hardware version of baseband processor
card.
Privileges
A/O
Example:
FullMax(device)# show bpc-hw-version
bpc-hw-version 1.10
afe-hw-ver
Hardware version of the Analog Front End (AFE)
Command
FullMax(device)#show
afe-hw-ver
Purpose
The command allows the user display the
hardware version of AFE.
Privileges
A/O
Example:
FullMax(device)# show afe-hw-ver
device-afe-hw-version 1.3
afe-sw-ver
Software version of the Analog Front End (AFE)
Command
FullMax(device)#show
afe-sw-ver
Purpose
The command allows the user display the
software version of AFE.
Privileges
A/O
Example:
FullMax(device)# show afe-sw-ver
device-afe-sw-version 1.3
build-sw-ver
Software version of the device general embedded software
Command
FullMax(device)#show
build-sw-ver
Purpose
The command allows the user display the
software version of the software build
Privileges
A/O
Example:
Full Spectrum Confidential
63
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(device)# show build-sw-ver
build-sw-version
5.2.12
Measurements
The Measurement group defines the commands that monitors or updates the
measurement related information in the private MIB. The user upon entering the device
command locks into the CLI to execute commands only related to Measurement.
FullMax#
FullMax# measurement
FullMax(measurement)#
Temperature
Temperature degree in Celsius
Command
FullMax(measurement)#show
temperature
Purpose
The command allows the user
display temperature of the
device.
FullMax(measurement)#track [- The command allows the user to
rN] [-tN] temperature
display real time temperature
sample of the device.
Privileges
A/O
A/O
Example:
FullMax(measurement)# show temperature
Temperature 45 degrees-Celsius
FullMax(measurement)# track –r3 –i2 temperature
Temperature 45 degrees-Celsius
Temperature 46 degrees-Celsius
Temperature 45 degrees-Celsius
Voltage
Voltage measurement
Command
FullMax(measurement)#
show voltage
FullMax(measurement)#
track [-rN] [-tN]
voltage
Purpose
The command allows the user display
voltage of the device.
The command allows the user to display
multiple voltage samples of the device.
Privileges
A/O
A/O
Example:
FullMax (measurement) # show voltage
Voltage 3 volts
FullMax (measurement) # track –r3 –i10 voltage
Full Spectrum Confidential
64
FullMax BS100 and MS400 User Manual Version 1.1
Voltage 3 volts
Voltage 3 volts
Voltage 3 volts
Current
Current measurements
Command
FullMax(measurement)#
show current
FullMax(measurement)#
track [-rN] [-tN]
current
Purpose
Privileges
The command allows the user display A/O
the current in the device.
The command allows the user to
A/O
display multiple current
measurements in the device.
Example:
FullMax (measurement) # show current
Current 2 amp
FullMax (measurement) # track –r4 current
Current 2 amp
Current 2 amp
Current 2 amp
Tx-power
Transmit power
Command
FullMax(measurement
)# show tx-power
FullMax(measurement)#
track [-rN] [-tN] txpower
Purpose
The command allows the user display
the transmit power.
Privileges
A/O
The command allows the user to display
multple transmit power measurements.
A/O
Example:
FullMax (measurement) # show tx-power
Tx-power 45 dBm
FullMax (measurement) # track –r2 tx-power
Tx-power 45 dBm
Tx-power 43 dBm
Rx-power
Receive power
Command
FullMax(measurement)#
Purpose
The command allows the user display
Full Spectrum Confidential
Privileges
A/O
65
FullMax BS100 and MS400 User Manual Version 1.1
show rx-power
FullMax(measurement)#
track [-rN] [-tN] rxpower
the receive power.
The command allows the user to display
multiple receive power measurements.
A/O
Example:
FullMax(measurement)# show rx-power
rx-power 45 dBm
FullMax(measurement)# track –r2 -i2 rx-power
rx-power 45 dBm
rx-power 45 dBm
afe-temperature
Read the temperature from the Analog Front End.
Command
FullMax(measurement)#
show afe-temperature
FullMax(measurement)#
track [-rN] [-tN]
afe-temperature
Purpose
The command allows the user display
temperatue from Analog Front End.
The command allows the user to track
the temperatue from Analog Front
End.
Privileges
A/O
A/O
Example:
FullMax(measurement)# show afe-temperatue
afe-temperature 27 celcius
FullMax(measurement)# track -r4 -i30 afe-temperatue
afe-temperature 27 celcius
afe-temperature 27 celcius
afe-temperature 27 celcius
afe-temperature 27 celcius
afe-rssi
Read the Receive Signal Strength Indicator (RSSI) from the Analog Front End.
Command
FullMax(measurement)#show
afe-rssi
FullMax(measurement)#track
[-rN] [-tN] afe-rssi
Purpose
The command allows the user display
RSSI from Analog Front End.
The command allows the user to track
RSSI from Analog Front End.
Privileges
A/O
A/O
Example:
FullMax(measurement)# show afe-rssi
afe-rssi 80 dBm
FullMax(measurement)# track -r3 -i30 afe-rssi
Full Spectrum Confidential
66
FullMax BS100 and MS400 User Manual Version 1.1
afe-rssi 80 dBm
afe-rssi 80 dBm
afe-rssi 80 dBm
5.2.13
pkm–config
pkm–config
The Pkm-Config group defines the commands that moniters or updates the Private Key
Management Version 2 Realated information in the Standard MIB .The user upon
entering the pkm-config command locks into this group to execute commands only
related to this group.
FullMax#
FullMax# pkm–config
FullMax(pkm–config)
Command
FullMax# pkm –config
Purpose
The command allows the user
to lock to pkm-config group
and display the pkm –config
prompt.
Privileges
A/O
FullMax# pkm–config
pkm-v2-config-table
This table conatins the configuration of the pkm attributes that are needed to pkm
operation.
Command
FullMax(pkm–
config)# show pkmv2-config-table
Purpose
The command allows the user display
all the Pkm V2 Config table parameter
Privileges
A/O
values.
Example:
FullMax(pkm–config)# show pkm-v2-config-table
pmk-pre-handshake-lifetime 10 second
pmk-lifetime 3600 seconds
sa-tek-challenge-timeout 10000 milliseconds
max-sa-tek-challenge 3
max-sa-tek-request 3
Full Spectrum Confidential
67
FullMax BS100 and MS400 User Manual Version 1.1
pkm-pmk-pre-handshake-lifetime
Defines the PkmPmkPrehandshakeLifetime.
Command
FullMax(pkm–
config)#set pkm-pmkpre-handshakelifetime 
FullMax(pkm–config)#show
pkm-pmk-pre-handshakelifetime
Purpose
The command allows the user update
Privileges
A/O
PkmPmkPrehandshakeLifetime.
A/O
The command allows the user to
display PkmPmkPrehandshakeLifetime
value
Example:
FullMax(pkm–config)# set pkm-pmk-pre-handshake-lifetime
11
Updated pkm-pmk-pre-handshake-lifetime 11 second
FullMax(pkm–config)# show pkm-pmk-pre-handshake-lifetime
pmk-pre-handshake-lifetime 10 second
pkm-pmk-lifetime
Defines the PMK life time
Command
FullMax(pkm–
config)#set pkm-pmklifetime 
FullMax(pkm–config)#show
pkm-pmk-lifetime
Purpose
The command allows the user to
update pkm-pmk-lifetime value
Privileges
The command allows the user
display pkm-pmk-lifetime.
A/O
Example:
FullMax(pkm–config) # set pkm-pmk-lifetime 3300
Updated pkm-pmk-lifetime 3300 seconds
FullMax(pkm–config) # show pkm-pmk-lifetime 3600 seconds
pkm-pmk-lifetime 3300 seconds
sa-challenge-timeout
This object defines the timeout value for SA-TEk challenge Retransmission.
Command
Purpose
Full Spectrum Confidential
Pri
vile
ges
68
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(pkm–
config)#set sachallenge-timeout

FullMax(pkm–config)#show
sa-challenge-timeout
The command allows the user to update A
sa-challenge-timeout.
The command allows the user display
sa-challenge-timeout.
A/O
Example:
FullMax(pkm–config) # set sa-challenge-timeout 666
updated value of sa-tek-challenge-timeout 666
millisecond
FullMax(pkm–config) # show sa-challenge-timeout
sa-tek-challenge-timeout 10000 milliseconds
max-sa-tek-challange
This object defines the maximum number of SA-TEK-Challenge Transmissions
Command
FullMax(pkm–
config)#set max-satek-challenge 
FullMax(pkm–config)#show
max-sa-tek-challange
Purpose
The command allows the user to update sachallenge-timeout.
Privileges
The command allows the user display max- A/O
sa-tek-challenge.
Example:
FullMax(pkm–config)# set max-sa-tek-challange 2
updated value of max-sa-tek-challenge 2
FullMax(pkm–config)# show max-sa-tek-challange
max-sa-tek-challenge 3
max-sa-tek-request
This object defines the maximum number of SA-TEK -Request retransmission.
Command
FullMax(pkm–
config)#set max-satek-request 
FullMax(pkm–config)#show
max-sa-tek-request
Purpose
Privileges
The command allows the user to update A
max-sa-tek-request.
The command allows the user to
display max-sa-tek-request.
Full Spectrum Confidential
A/O
69
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(pkm–config)# set max-sa-tek-request 2
updated value of max-sa-tek-request 2
FullMax(pkm–config)# show max-sa-tek-request
max-sa-tek-request 3
all
The command allows the user to display all the parameters of the tables in this group.
Command
FullMax(pkm–config)#show
all
Purpose
The command allows the user to display
all the parameters values of the in this
group.
Privileges
A/O
FullMax(pkm–config) # show all
pmk-pre-handshake-lifetime 10 second
pmk-lifetime 3600 seconds
sa-tek-challenge-timeout 10000 milliseconds
max-sa-tek-challenge 3
max-sa-tek-request 3
5.2.14
bs-private
FullMax#
FullMax# bs-private
FullMax(bs-private)#
Command
FullMax#bs-private
bs-rx-amc-count-table
Purpose
The command allows the user to lock
to bs-private group and display the bsprivate prompt.
Privileges
A/O
This table contains statistical information that can be used to characterize the adaptive
modulation and coding performance in the uplink.
Command
FullMax(bs-private)# show
bs-rx-amc-count-table

Purpose
This command shows all the
parameters and their values for
AmcCountTable
Privileges
A/O
Example:
FullMax(bs-private)# show bs-rx-amc-count-table 1
bs-rx-octets for uiuc index 1 is 0
Full Spectrum Confidential
70
FullMax BS100 and MS400 User Manual Version 1.1
bs-rx-packets for uiuc index 1 is 0
bs-tx-erroredpackets for uiuc index 1 is 0
bs-rx-uiuc-index
The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message,
and is used along with ifIndex to identify an entry in the
wmanIf2BsOfdmaUcdBurstProfileTable.
Command
FullMax(bs-private)#show
bs-rx-uiuc-index
Purpose
Show all the Uplink Interval Usage
Code index available.A/O
Privileges
A/O
Example:
FullMax(bs-private)# show bs-rx-uiuc-index
uiuc indices are
bs-ul-uiuc-index: 1
bs-ul-uiuc-index: 2
bs-ul-uiuc-index: 3
bs-ul-uiuc-index: 4
bs-ul-uiuc-index: 5
bs-ul-uiuc-index: 6
bs-ul-uiuc-index: 7
bs-ul-uiuc-index: 8
bs-ul-uiuc-index: 9
bs-ul-uiuc-index: 10
bs-rx-octets
This object counts the number of octets received in the uplink using the uplink burst
profile indexed by wmanPriBsRxUiucIndex.
Command
FullMax(bs-private)#show
bs-rx-octets 
Purpose
Show the no of octet received in the
uplink for the given index
Privileges
A/O
Example:
FullMax(bs-private)# show bs-rx-octets 1
bs-rx-octets for uiuc index 1 is 0
bs-rx-packets
This object counts the number of packets received in the uplinkusing the uplink burst
profile indexed by UiucIndex
Command
FullMax(bsprivate)#show bs-
Purpose
Shows the number of packets
received in the uplink for the
Full Spectrum Confidential
Privileges
A/O
71
FullMax BS100 and MS400 User Manual Version 1.1
rx-packets 
given index
Example:
FullMax(bs-private)# show bs-rx-packets 1
bs-rx-packets for uiuc index 1 is 0
bs-rx-erroredPackets
This object counts the number of errored packets received in the uplink using the uplink
burst profile indexed by UiucIndex.
Command
Purpose
FullMax(bs-private)#show Shows the number of errored packets
received in the uplink for the given index
bs-rx-erroredPackets

Privileges
A/O
Example:
FullMax(bs-private)# show bs-rx-erroredPackets 1
bs-tx-errored packets for uiuc index 1 is 0
bs-tx-amc-count-table
This table contains statistical information that can be used to characterize the adaptive
modulation and coding performance in the downlink.
Command
FullMax(bs-private)#show
bs-tx-amc-count-table

Purpose
Show all the parameters and their
values of the TxAmcCountTable
table for the given index
Privileges
A/O
Example:
FullMax(bs-private)# show bs-tx-amc-count-table 1
bs-tx-octets for diuc index 1 is 0
bs-tx-packets for diuc index 1 is 0
bsbs-txtx-diucdiuc-index
The Downlink Interval Usage Code indicates the downlink burst profile in the DCD
message.
Command
FullMax(bs-private)#show
bs-tx-diuc-index
Purpose
Show all the available Downlink
Interval Usage indices.
Privileges
A/O
Example:
FullMax(bs-private)# show bs-tx-diuc-index
diuc indices are
Full Spectrum Confidential
72
FullMax BS100 and MS400 User Manual Version 1.1
bs-dl-diuc-index: 0
bs-dl-diuc-index: 1
bs-dl-diuc-index: 2
bs-dl-diuc-index: 3
bs-dl-diuc-index: 4
bs-dl-diuc-index: 5
bs-dl-diuc-index: 6
bs-dl-diuc-index: 7
bs-dl-diuc-index: 8
bs-dl-diuc-index: 9
bs-dl-diuc-index: 10
bs-dl-diuc-index: 11
bs-dl-diuc-index: 12
bs-tx-octets
This object counts the number of octets transmitted in the downlink using the downlink
burst profile indexed by DiucIndex.
Command
FullMax(bs-private)# show
bs-tx-octets 
Purpose
Shows the number of octets
transmitted in the downlink for the
given index
Privileges
A/O
Example:
FullMax(bs-private)# show bs-tx-octets 1
bs-tx-octets for diuc index 1 is 0
bs-tx-packets
This object counts the number of packets transmitted in the downlink using the downlink
burst profile indexed by Diuc Index.
Command
FullMax(bs-rivate)#show
bs-tx-packets 
Purpose
Shows the number of packets
transmitted in the downlink for the
given index
Privileges
A/O
Example:
FullMax(bs-private)# show bs-tx-packets 1
bs-tx-packets for diuc index 1 is 0
cmn-sf-table
This Table measures service flow traffic .
Command
FullMax(bs-private)#show
cmn-sf-table 
Purpose
This command show all the
parameters and their values of Cmn-
Full Spectrum Confidential
Privileges
A/O
73
FullMax BS100 and MS400 User Manual Version 1.1
sf-table.
Example:
FullMax(bs-private)# show cmn-sf-table 2001
sf-total-octets for sfid 2001 is 100
sf-total-pkts for sfid 2001 is 2
sf-errored-pkts for sfid 2001 is 1
sf-frag-orig for sfid 2001 is 1
sf-frag-total for sfid 2001 is 2
sf-missing-frag for sfid 2001 is 0
cmn-pm-sfid
This is a 32 bit quantity that uniquely identifies a service flow to both the subscriber
station and base station.
Command
FullMax(bs-private)#show
cmn-pm-sfid 
Purpose
This command shows all the
avaliable Service Flow Id's
Avaliable for a particular MSID.
Privileges
A/O
Example :
FullMax(bs-private)# show cmn-pm-sfid 112233:445566
cmn-pm-sfid 2001
cmn-pm-sfid 2002
cmn-pm-sfid 2003
cmn-pm-sfid 2006
sf-total-octets
This determines the total octets received/transmitted on this service flow.
Command
FullMax(bs-private)# show
sf-total-octets 
Purpose
This command allows the user to
diplay the total octets received or
transmitted for this service-flow.
Privileges
A/O
Example:
FullMax(bs-private)#show sf-total-octets 2001
sf-total-octets for sfid (2001) : 1000
sf-total-pkts
This determines the total number of packets received /transmitted on this service flow.
Command
FullMax(bs-private)#show
sf-total-pkts 
Purpose
This Command allows the user to
display the total packets received or
trasmitted for this service-flow
Full Spectrum Confidential
Privileges
A/O
74
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(bs-private)#show sf-total-pkts 2001
sf-total-pkts for sfid (2001): 22
sf-errored-pkts
This determines number of packets that were dropped due to missing fragments / bad
ARQ blocks.
Command
FullMax(bs-private)#show
sf-errored-pkts 
Purpose
This Command Allows the user to
display the total errored packets
received or transmitted for this
service flow.
Privileges
A/O
Example:
FullMax(bs-private)# show sf-errored-pkts 2001
sf-errored-pkts for sfid (2001): 1
sfsf-fragfrag-orig
This determines number of fragments / ARQ blocks originally transmitted/received on
this service flow.
Command
FullMax(bs-private)#show
sf-frag-orig 
Purpose
This Command allows the user to
display the total fragments
received or transmitted originally
on this service flow.
Privileges
A/O
Example:
FullMax(bs-private)#show sf-frag-orig 2001
sf-frag-orig for sfid (2001) : 2
sfsf-fragfrag-total
This determines total fragments / ARQ blocks transmitted / received on this service
flow.
Command
FullMax(bs-private)#show
sf-frag-total 
Purpose
This Command allows the user to
display the total fragments received
or transmitted on this service flow.
Example:
FullMax(bs-private)# show sf-frag-total
Full Spectrum Confidential
Privileges
A/O
2001
75
FullMax BS100 and MS400 User Manual Version 1.1
sf-frag-total for sfid (2001): 2
sfsf-missingmissing-frag
Description
This determines the number of missing received fragments received or NACK.
Command
FullMax(bs-private)#
show sf-missing-frag

Purpose
This command allows the user to
display the number of missing received
fragments or NACK.
Privileges
A/O
Example:
FullMax(bs-private)# show sf-missing-frag 2001
sf-missing-frag for sfid (2001): 1
5.2.15
trap-config
traptrap-config
This Command allows the user to lock to trap config group.
Purpose
Command
FullMax # trap- This command allows the user
to Locks to the trap config
config
group and displays the
coresponding group prompt.
Privileges
A/O
Example:
FullMax # trap-config
FullMax(trap-config) #
stdstd-traptrap-ctrl
The object is used to enable or disable Base Station traps From left to right, the set bit
indicates the corresponding Base Station trap is enabled
{wmanIf2BsSsStatusNotification (0),
wmanIf2BsSsDynamicServiceFail (1),
wmanIf2BsSsRssiStatusChange (2),
wmanIf2BsSsRegister
(3),
wmanIf2BsSsPkmFail
(4),
wmanIf2BsPerformanceCounters (5)}
Command
FullMax(trapconfig) # set
std-trap-ctrl
Purpose
Privileges
This command Allows the
user to update the value of stdtrap-ctrl parameter.
Full Spectrum Confidential
76
FullMax BS100 and MS400 User Manual Version 1.1

FullMax(trap-config)
# show std-trap-ctrl
This command Allows the
user to display the value of
std-trap-ctrl parameter.
A/O
Example:
FullMax(trap-config) # set std-trap-ctrl 25
updated bs-trap-control {wmanIf2BsSsStatusNotification(0),
wmanIf2BsSsRegister(3),
wmanIf2BsPerformanceCounters (4)
FullMax(bs-private)# show std-trap-ctrl
bs-trap-control enabled are {
wmanIf2BsSsStatusNotification(0),
wmanIf2BsSsRegister(3),
wmanIf2BsPerformanceCounters
(4) }
stdstd-traptrap-statusstatus-ctrl
The object is used to enable or disable Base Station status notification traps.
The set bit indicates the corresponding Base Station trap is enabled.
{ unused(0), ssInitRangingSucc(1), ssInitRangingFail(2), ssRegistered(3),
ssRegistrationFail(4), ssDeregistered(5), ssBasicCapabilitySucc(6),
ssBasicCapabilityFail(7), ssAuthorizationSucc(8), ssAuthorizationFail(9),
tftpSucc(10), tftpFail(11), sfCreationSucc(12), sfCreationFail(13) }
Command
FullMax(trapconfig) # set
std-trapstatus-ctrl

FullMax(trap-config)
# show std-trapstatus-ctrl
Purpose
Privileges
This command Allows the
user to update the value of stdtrap-status-ctrl parameter.
This command Allows the
user to display the value of
std-trap-status-ctrl parameter.
A/O
FullMax(bs-private)# set std-trap-status-ctrl 10900
updated bs-trap-status-ctrl
{ssInitRangingFail(2),
ssRegistrationFail(4),
ssBasicCapabilityFail(7),ssAuthorizationFail(9),
tftpFail(11), sfCreationFail(13) }
Full Spectrum Confidential
77
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(bs-private)# show std-trap-status-ctrl
bs-trap-status-ctrl enabled are
{ssInitRangingFail(2),
ssRegistrationFail(4),
ssBasicCapabilityFail(7),ssAuthorizationFail(9),
tftpFail(11), sfCreationFail(13) }
privateprivate-traptrap-ctrl
The object is used to enable or disable Base Station traps From left to right, the set bit
indicates the corresponding Base Station trap is enabled.
{ wmanPriPowerStatusChange (0), wmanPriFanStatusChange (1),
wmanPriTemperatureChange (2), wmanPriConfigChange (3),
wmanPriAfeBitError (4) }
Command
FullMax(trapconfig) # set
private-trapctrl 
FullMax(trap-config)
# show private-trapctrl
Purpose
This command Allows the
user to update the value of
private-trap-ctrl parameter.
Privileges
This command Allows the
user to display the value of
private-trap-ctrl parameter.
A/O
FullMax(bs-private)# set private-trap-ctrl 21
updated private-trap-ctrl
{ wmanPriPowerStatusChange(0),
wmanPriPowerStatusChange(2),
wmanPriPowerStatusChange (4)}
FullMax(bs-private)# show private-trap-ctrl
private-trap-ctl enabled
{ wmanPriPowerStatusChange(0),
wmanPriPowerStatusChange(2),
wmanPriPowerStatusChange (4)}
5.2.16
lapc-config
LapcLapc-config
This group contains commands to manipulate the Link Adaption and Power Control
configuration parameters for the Base Station MAC.
Command
Purpose
Full Spectrum Confidential
78
FullMax BS100 and MS400 User Manual Version 1.1
FullMax#lapc-config
The command allows the user to lock to config group
and display the config prompt.
FULLMAX#lapc-config
FULLMAX(lapc-config)]#
uiuc
Command
FullMax(lapc-config)#
show uiuc
Purpose
Shows the values of uiuc avaliable.
Example:
FULLMAX(lapc-config)#show uiuc
uiuc 1
uiuc 2
Uplink_FEC_Code_Type
Command
Purpose
FullMax(lapc-config)#
The command sets the value of
set Uplink_FEC_Code_Type Uplink_FEC_Code_Type for the given index
 value
The command show the value of
FullMax(lapc-config)#
show Uplink_FEC_Code_Type Uplink_FEC_Code_Type for the particunlar uiuc
index

Example:
FULLMAX(lapc-config)#set Uplink_FEC_Code_Type 1 333
Updated Uplink_FEC_Code_Type for uiuc index 1 is 333
FULLMAX(lapc-config)#show Uplink_FEC_Code_Type 1
Uplink_FEC_Code_Type for uiuc index 1 is 0
Ranging_Data_Ratio
Command
FullMax(lapc-config)#
set Ranging_Data_Ratio

FullMax(lapc-config)#
show Ranging_Data_Ratio

Purpose
The command sets the value of Ranging_Data_Ratio
for the given index.
The command shows the value of
Ranging_Data_Ratio for the given index.
Example:
Full Spectrum Confidential
79
FullMax BS100 and MS400 User Manual Version 1.1
FULLMAX(lapc-config)#set Ranging_Data_Ratio 1 22
Updated Ranging_Data_Ratio for uiuc index 1 is 22
FULLMAX(lapc-config)#show Ranging_Data_Ratio 1
Ranging_Data_Ratio for uiuc index 1 is 19
Normalised_C_by_N_Mantissa
Command
FullMax(lapc-config)#
set
Normalised_C_by_N_Mantis
sa 
FullMax(lapc-config)#
show
Normalised_C_by_N_Mantis
sa 
Purpose
The commnad sets the value of
Normalised_C_by_N_Mantissa for the given index
The commnad shows the value of
Normalised_C_by_N_Mantissa for the given index
Example:
FULLMAX(lapc-config)#set Normalised_C_by_N_Mantissa 1 77
Updated Normalised_C_by_N_Mantissa for uiuc index 1 is
77
FULLMAX(lapc-config)#show Normalised_C_by_N_Mantissa 1
Normalised_C_by_N_Mantissa for uiuc index 1 is 60
Normalised_C_by_N_Exponent
Command
Purpose
FullMax(lapc-config)#
The command sets the value of
set
Normalised_C_by_N_Exponent for the given index
Normalised_C_by_N_Expone
nt 
FullMax(lapc-config)#
The command shows the value of
show
Normalised_C_by_N_Exponent for the given index
Normalised_C_by_N_Expone
nt 
Example:
FULLMAX(lapc-config)#set Normalised_C_by_N_Exponent 1 1
Updated Normalised_C_by_N_Exponent for index 1 is 1
FULLMAX(lapc-config)#show Normalised_C_by_N_Exponent 1
Normalised_C_by_N_Exponent for index 1 is -1
FIR_filter_coefficient_mantissa
Full Spectrum Confidential
80
FullMax BS100 and MS400 User Manual Version 1.1
Command
Purpose
FullMax(lapc-config)#
The command sets the value of
set
FIR_filter_coefficient_mantissa for the given index
FIR_filter_coefficient_ma
ntissa  value
FullMax(lapc-config)#
The command shows the value of
show
FIR_filter_coefficient_mantissa for the given
FIR_filter_coefficient_ma
index
ntissa 
Example:
FULLMAX(lapc-config)#set FIR_filter_coefficient_mantissa 1
65
Updated FIR_filter_coefficient_mantissa for index 1 is
65
FULLMAX(lapc-config)#show FIR_filter_coefficient_mantissa 1
FIR_filter_coefficient_mantissa for index 1 is 65
FIR_filter_coefficient_TenPwr
Command
Purpose
FullMax(lapc-config)#set
The command sets the value of
FIR_filter_coefficient_TenP FIR_filter_coefficient_TenPwr for the given index.
wr  
FullMax(lapc-config)#show
The command shows the value of
FIR_filter_coefficient_TenP FIR_filter_coefficient_TenPwr for the given index.
wr 
Example:
FULLMAX(lapc-config)#set FIR_filter_coefficient_TenPwr 1 3
Updated FIR_filter_coefficient_TenPwr for index 1 is 3
FULLMAX(lapc-config)#show FIR_filter_coefficient_TenPwr 1
FIR_filter_coefficient_TenPwr for index 1 is 3
Dl_Benchmark_Entry_Threshold_CINR
Description
Command
FullMax(lapc-config)#set
Dl_Benchmark_Entry_Threshold_C
INR 
 
FullMax(lapc-config)#show
Dl_Benchmark_Entry_Threshold_C
Purpose
Sets the value of
Dl_Benchmark_Entry_Threshold_CINR for the
given fec code and repetition .
Displays the value of
Dl_Benchmark_Entry_Threshold_CINR for the
Full Spectrum Confidential
81
FullMax BS100 and MS400 User Manual Version 1.1
INR 

given fec code and repetition .
Example:
FULLMAX(lapc-config)#set Dl_Benchmark_Entry_Threshold_CINR
4 2 41e3
Updated Dl_Benchmark_Entry_Threshold_CINR for fec code
and repition 2 is 41e3
FULLMAX(lapc-config)#show Dl_Benchmark_Entry_Threshold_CINR
4 2
Dl_Benchmark_Entry_Threshold_CINR for fec code 4 and
repition 2 is 19e1
Dl_Benchmark_Exit_Threshold_CINR
Description
Command
Purpose
FullMax(lapc-config)#set
Sets the value of
Dl_Benchmark_Exit_Threshold_CI Dl_Benchmark_Exit_Threshold_CINR for the
NR 
given fec code and repetition .
 
Displays the value of
FullMax(lapc-config)#show
Dl_Benchmark_Exit_Threshold_CI Dl_Benchmark_Exit_Threshold_CINR for the
given fec code and repetition .
NR 

Example:
FULLMAX(lapc-config)#set Dl_Benchmark_Exit_Threshold_CINR 4
2 41e3
Updated Dl_Benchmark_Exit_Threshold_CINR for fec code
4 and
repition 2 is 41e3
FULLMAX(lapc-config)#show Dl_Benchmark_Exit_Threshold_CINR
4 2
Dl_Benchmark_Exit_Threshold_CINR for fec code 4 and
repition 2 is 19e1
Ul_Benchmark_Entry_Threshold_CINR
Command
Purpose
FullMax(lapc-config)#set
Sets the value of
Ul_Benchmark_Entry_Threshold_C Ul_Benchmark_Entry_Threshold_CINR for the
Full Spectrum Confidential
82
FullMax BS100 and MS400 User Manual Version 1.1
INR 
 
FullMax(lapc-config)#show
Ul_Benchmark_Entry_Threshold_C
INR 

given fec code and repetition .
Displays the value of
Ul_Benchmark_Entry_Threshold_CINR for the
given fec code and repetition .
FULLMAX(lapc-config)#set Ul_Benchmark_Entry_Threshold_CINR
4 2 41e3
Updated Ul_Benchmark_Entry_Threshold_CINR for fec code
and repition 2 is 41e3
FULLMAX(lapc-config)#show Ul_Benchmark_Entry_Threshold_CINR
4 2
Ul_Benchmark_Entry_Threshold_CINR for fec code 4 and
repition 2 is 19e1
Ul_Benchmark_Exit_Threshold_CINR
Description
Command
FullMax(lapc-config)#set
Ul_Benchmark_Exit_Threshold_CI
NR 
 
FullMax(lapc-config)#show
Ul_Benchmark_Exit_Threshold_CI
NR 

Purpose
Sets the value of
Ul_Benchmark_Exit_Threshold_CINR for the
given fec code and repetition .
Displays the value of
Ul_Benchmark_Exit_Threshold_CINR for the
given fec code and repetition .
Example:
FULLMAX(lapc-config)#set Dl_Benchmark_Exit_Threshold_CINR 4
2 41e3
Updated Dl_Benchmark_Exit_Threshold_CINR for fec code
4 and repition 2 is 41e3
FULLMAX(lapc-config)#show Dl_Benchmark_Exit_Threshold_CINR
4 2
Dl_Benchmark_Exit_Threshold_CINR for fec code 4 and
repition 2 is 19e1
Burst_Profile_evaluation_Timer
Command
Purpose
Full Spectrum Confidential
83
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(lapc-config)#set
Burst_Profile_evaluation_Timer
FullMax(lapc-config)#show
Burst_Profile_evaluation_Timer
The command sets the value of
_Profile_evaluation_Timer
The command shows the value of
_Profile_evaluation_Timer
Example:
FULLMAX(lapc-config)#set Burst_Profile_evaluation_Timer 222
Updated Burst_Profile_evaluation_Timer: 250
FULLMAX(lapc-config)#show Burst_Profile_evaluation_Timer
Burst_Profile_evaluation_Timer: 250
Mantissa_Lower_Thld_Rx_Power_Density
Description
Command
FullMax(lapc-config)# set
Mantissa_Lower_Thld_Rx_Power_Densi
ty 
FullMax(lapc-config)# show
Mantissa_Lower_Thld_Rx_Power_Densi
ty
Purpose
Sets the value of
Mantissa_Lower_Thld_Rx_Power_Density
Displays the value of
Mantissa_Lower_Thld_Rx_Power_Density.
Example:
FULLMAX(lapc-config)#set
Mantissa_Lower_Thld_Rx_Power_Density 22
Updated Mantissa_Lower_Thld_Rx_Power_Density -100
FULLMAX(lapc-config)#show
Mantissa_Lower_Thld_Rx_Power_Density
Mantissa_Lower_Thld_Rx_Power_Density -100
Mantissa_Higher_Thld_Rx_Power_Density
Description
Command
FullMax(lapc-config)#set
Mantissa_Higher_Thld_Rx_Power_Dens
ity
FullMax(lapc-config)#show
Mantissa_Higher_Thld_Rx_Power_Dens
ity
Purpose
Sets the value of
Mantissa_Higher_Thld_Rx_Power_Density to the
given value.
Display the value of
Mantissa_Higher_Thld_Rx_Power_Density
Example:
Full Spectrum Confidential
84
FullMax BS100 and MS400 User Manual Version 1.1
FULLMAX(lapc-config)#set
Mantissa_Higher_Thld_Rx_Power_Density 22
Updated Mantissa_Higher_Thld_Rx_Power_Density 22
FULLMAX(lapc-config)#show
Mantissa_Higher_Thld_Rx_Power_Density
Mantissa_Higher_Thld_Rx_Power_Density -60
Max_Length_Of_DLMAP_Mesg
Command
FullMax(lapc-config)#set
Max_Length_Of_DLMAP_Mesg 
FullMax(lapc-config)#show
Max_Length_Of_DLMAP_Mesg
Purpose
The command sets the value of
_Length_Of_DLMAP_Mesg to the value given
The command shows the value of
_Length_Of_DLMAP_Mesg
Example:
FULLMAX(lapc-config)#set Max_Length_Of_DLMAP_Mesg 22
Updated Max_Length_Of_DLMAP_Mesg: 22
FULLMAX(lapc-config)#show Max_Length_Of_DLMAP_Mesg
Max_Length_Of_DLMAP_Mesg: 2
Max_Aggregate_Length_Of_Control_Messages
Command
Purpose
FullMax(lapc-config)# set
The command sets the value of
Max_Aggregate_Length_Of_Control_M _Aggregate_Length_Of_Control_Messages to the
essages 
given value.
The
command shows the value of
FullMax(lapc-config)# show
Max_Aggregate_Length_Of_Control_M _Aggregate_Length_Of_Control_Messages.
essages
Example:
FULLMAX(lapc-config)#set
Max_Aggregate_Length_Of_Control_Messages 22
Updated Max_Aggregate_Length_Of_Control_Messages: 22
FULLMAX(lapc-config)#show
Max_Aggregate_Length_Of_Control_Messages
Max_Length_Of_DLMAP_Mesg: 48
Max_No_Of_Slots_Used_For_Future_Allocation_In_DL
Full Spectrum Confidential
85
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(lapc-config)# set
Max_No_Of_Slots_Used_For_Future_Al
location_In_DL 
FullMax(lapc-config)# show
Max_No_Of_Slots_Used_For_Future_Al
location_In_DL
Purpose
The command sets the value of
_No_Of_Slots_Used_For_Future_Allocation_In_D
L to the given value.
The command shows the value of
_No_Of_Slots_Used_For_Future_Allocation_In_D
L.
Example:
[FULLMAX(lapc-config)]$set
Max_No_Of_Slots_Used_For_Future_Allocation_In_DL 33
Updated Max_No_Of_Slots_Used_For_Future_Allocation_In_DL:
33
[FULLMAX(lapc-config)]$show
Max_No_Of_Slots_Used_For_Future_Allocation_In_DL
Max_Aggregate_Length_Of_Control_Messages: 90
Max_No_Of_Slots_Used_For_Future_Allocation_In_UL
Command
FullMax(lapc-config)# set
Max_No_Of_Slots_Used_For_Future_Al
location_In_UL 
FullMax(lapc-config)# show
Max_No_Of_Slots_Used_For_Future_Al
location_In_UL
Purpose
The command sets the value of
_No_Of_Slots_Used_For_Future_Allocation_In_U
L to the given value.
The command shows the value of
_No_Of_Slots_Used_For_Future_Allocation_In_U
L.
Example:
FULLMAX(lapc-config)#set
Max_No_Of_Slots_Used_For_Future_Allocation_In_UL 44
Updated Max_No_Of_Slots_Used_For_Future_Allocation_In_DL:
44
FULLMAX(lapc-config)#show
Max_No_Of_Slots_Used_For_Future_Allocation_In_UL
Max_No_Of_Slots_Used_For_Future_Allocation_In_DL: 10
Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame
Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_UL_Frame
Full Spectrum Confidential
86
FullMax BS100 and MS400 User Manual Version 1.1
Command
Purpose
FullMax(lapc-config)#set
The command sets the value of
Max_No_Of_Slots_Can_Be_Used_For_C _No_Of_Slots_Can_Be_Used_For_CDMA_Alloca
DMA_Allocation_In_Single_UL_Frame tion_In_Single_UL_Frame to the given value.

FullMax(lapc-config)#show
The command shows the value of
Max_No_Of_Slots_Can_Be_Used_For_C _No_Of_Slots_Can_Be_Used_For_CDMA_Alloca
DMA_Allocation_In_Single_UL_Frame tion_In_Single_UL_Frame.
Example:
FULLMAX(lapc-config)#set
Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_U
L_Frame 22
Updated
Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_U
L_Frame: 22
FULLMAX(lapc-config)#show
Max_No_Of_Slots_Can_Be_Used_For_CDMA_Allocation_In_Single_U
L_Frame
Max_No_Of_Slots_Used_For_Future_Allocation_In_DL: 10
No_Of_CDMA_Ranging_Slots
Command
Purpose
FullMax(lapc-config)# set
The command sets the value of
No_Of_CDMA_Ranging_Slots  _Of_CDMA_Ranging_Slots to the given
value.
FullMax(lapc-config)# show
The command shows the value of
No_Of_CDMA_Ranging_Slots
_Of_CDMA_Ranging_Slots.
FULLMAX(lapc-config)#set No_Of_CDMA_Ranging_Slots 33
Updated No_Of_CDMA_Ranging_Slots: 33
FULLMAX(lapc-config)#show No_Of_CDMA_Ranging_Slots
No_Of_CDMA_Ranging_Slots: 1
CDMA_Ranging_Period
Command
FullMax(lapc-config)# set
CDMA_Band_Width_Period 
FullMax(lapc-config)# show
Purpose
The command sets the value of
CDMA_Band_Width_Period to the given value.
The command shows the value of
Full Spectrum Confidential
87
FullMax BS100 and MS400 User Manual Version 1.1
CDMA_Band_Width_Period
CDMA_Band_Width_Period
FULLMAX(lapc-config)#set CDMA_Band_Width_Period 33
Updated CDMA_Band_Width_Period: 33
FULLMAX(lapc-config)#show CDMA_Band_Width_Period
CDMA_Band_Width_Period: 6
No_Of_CDMA_Band_Width_Slots
Command
Purpose
FullMax(lapc-config)# set
The command sets the value of
No_Of_CDMA_Band_Width_Slots
_Of_CDMA_Band_Width_Slots to the given value

FullMax(lapc-config)# show
The command shows the value of
No_Of_CDMA_Band_Width_Slots
_Of_CDMA_Band_Width_Slots
Example:
FULLMAX(lapc-config)#set No_Of_CDMA_Band_Width_Slots 33
Updated No_Of_CDMA_Band_Width_Slots: 33
FULLMAX(lapc-config)#show No_Of_CDMA_Band_Width_Slots
No_Of_CDMA_Band_Width_Slots: 3
CDMA_Band_Width_Period
Command
FullMax(lapc-config)# set
CDMA_Band_Width_Period 
FullMax(lapc-config)# show
CDMA_Band_Width_Period
Purpose
The command sets the value of
_Band_Width_Period to the given value.
The command shows the value of
_Band_Width_Period.
Example:
FULLMAX(lapc-config)#set CDMA_Band_Width_Period 33
Updated CDMA_Band_Width_Period: 33
FULLMAX(lapc-config)#show CDMA_Band_Width_Period
CDMA_Band_Width_Period: 6
Max_Frame_Slots_Dl_Harq_Retransmission
Command
FullMax(lapc-config)# set
Max_Frame_Slots_Dl_Harq_Retransm
ission 
Purpose
The command sets the value of
_Frame_Slots_Dl_Harq_Retransmission to the
given value.
Full Spectrum Confidential
88
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(lapc-config)# show
The command shows the value of
Max_Frame_Slots_Dl_Harq_Retransm _Frame_Slots_Dl_Harq_Retransmission.
ission
Example:
FULLMAX(lapc-config)#set
Max_Frame_Slots_Dl_Harq_Retransmission 33
Updated Max_Frame_Slots_Dl_Harq_Retransmission 33
FULLMAX(lapc-config)#show
Max_Frame_Slots_Dl_Harq_Retransmission
Max_Frame_Slots_Dl_Harq_Retransmission: 20
Max_Frame_Slots_Ul_Harq_Retransmission
Command
FullMax(lapc-config)# set
Max_Frame_Slots_Ul_Harq_Retransm
ission 
FullMax(lapc-config)# show
Max_Frame_Slots_Ul_Harq_Retransm
ission
Purpose
The command sets the value of
Max_Frame_Slots_Ul_Harq_Retransmission to the
given value.
The command shows the value of
_Frame_Slots_Ul_Harq_Retransmission.
Example:
FULLMAX(lapc-config)#set
Max_Frame_Slots_Ul_Harq_Retransmission 33
Update Max_Frame_Slots_Ul_Harq_Retransmission: 33
FULLMAX(lapc-config)#show
Max_Frame_Slots_Ul_Harq_Retransmission
Max_Frame_Slots_Ul_Harq_Retransmission: 20
Max_Ul_Harq_Ack_slots
Command
FullMax(lapc-config)# set
Max_Ul_Harq_Ack_slots 
FullMax(lapc-config)# show
Max_Ul_Harq_Ack_slots
Purpose
The command sets the value of
Max_Ul_Harq_Ack_slots to the givan value.
The command shows the value of
Max_Ul_Harq_Ack_slots
Example:
FULLMAX(lapc-config)#set Max_Ul_Harq_Ack_slots 24
Updated Max_Ul_Harq_Ack_slots: 24
FULLMAX(lapc-config)#show Max_Ul_Harq_Ack_slots
Full Spectrum Confidential
89
FullMax BS100 and MS400 User Manual Version 1.1
Max_Ul_Harq_Ack_slots: 2
Initial_Ranging_Backoff_Start
Command
FullMax(lapc-config)# set
Initial_Ranging_Backoff_Start

FullMax(lapc-config)# show
Initial_Ranging_Backoff_Start
Purpose
The command sets the value of
_Ranging_Backoff_Start to the given value.
The command shows the value of
_Ranging_Backoff_Start
Example:
FULLMAX(lapc-config)#set Initial_Ranging_Backoff_Start
55
Updated Initial_Ranging_Backoff_Start: 55
FULLMAX(lapc-config)#show Initial_Ranging_Backoff_Start
Initial_Ranging_Backoff_Start: 15
Initial_Ranging_Backoff_End
Command
FullMax(lapc-config)# set
Initial_Ranging_Backoff_End

FullMax(lapc-config)# show
Initial_Ranging_Backoff_End
Purpose
The command sets the value of
_Ranging_Backoff_End to the given value.
The command shows the value of
_Ranging_Backoff_End.
FULLMAX(lapc-config)#set Initial_Ranging_Backoff_End 44
Updated Initial_Ranging_Backoff_End: 44
FULLMAX(lapc-config)#show Initial_Ranging_Backoff_End
Initial_Ranging_Backoff_End: 12
Bandwidth_Request_Backoff_Start
Command
FullMax(lapc-config)# set
Bandwidth_Request_Backoff_Start

FullMax(lapc-config)# show
Bandwidth_Request_Backoff_Start
Purpose
The command sets the value of
_Request_Backoff_Start to the given value.
The command shows the value of
_Request_Backoff_Start.
Example:
Full Spectrum Confidential
90
FullMax BS100 and MS400 User Manual Version 1.1
FULLMAX(lapc-config)#set Bandwidth_Request_Backoff_Start 44
Updated Bandwidth_Request_Backoff_Start: 44
FULLMAX(lapc-config)#show Bandwidth_Request_Backoff_Start
Bandwidth_Request_Backoff_Start: 3
Bandwidth_Request_Backoff_End
Command
FullMax(lapc-config)# set
Bandwidth_Request_Backoff_End

FullMax(lapc-config)# show
Bandwidth_Request_Backoff_End
Purpose
The
command
sets
the
value
_Request_Backoff_End to the given value.
The
command
shows
_Request_Backoff_End.
the
value
Example:
FULLMAX(lapc-config)#set Bandwidth_Request_Backoff_End 55
Updated Bandwidth_Request_Backoff_End: 55
FULLMAX(lapc-config)#show Bandwidth_Request_Backoff_End
Bandwidth_Request_Backoff_End: 2
Percentage_Of_Reserved_Symbols
Command
FullMax(lapc-config)# set
Percentage_Of_Reserved_Symbols

FullMax(lapc-config)# show
Percentage_Of_Reserved_Symbols
Purpose
The command sets the value of
_Of_Reserved_Symbols to the given value.
The command shows the value of
_Of_Reserved_Symbols.
Example:
FULLMAX(lapc-config)#set Percentage_Of_Reserved_Symbols 99
Updated Percentage_Of_Reserved_Symbols: 99
FULLMAX(lapc-config)#show Percentage_Of_Reserved_Symbols
Percentage_Of_Reserved_Symbols: 10
Percentags_Of_Head_Room_For_MAC
Command
Purpose
The command sets the value of
FullMax(lapc-config)# set
Percentags_Of_Head_Room_For_MAC _Of_Head_Room_For_MAC to the given
value.

Full Spectrum Confidential
91
of
of
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(lapc-config)# show
The command shows the value of
Percentags_Of_Head_Room_For_MAC _Of_Head_Room_For_MAC.
Example:
FULLMAX(lapc-config)#set Percentags_Of_Head_Room_For_MAC 88
Updated Percentags_Of_Head_Room_For_MAC: 88
FULLMAX(lapc-config)#show Percentags_Of_Head_Room_For_MAC
Percentags_Of_Head_Room_For_MAC: 10
5.3 MS400 Operation
The FullMax MS CLI supports the following commands. The access to this commands
are based on the user privileges. The Admin has the privilege to control and monitor all
the information supported by the FullMax MS CLI commands, where as the operator has
limited privileges.
After the successful authentication, the user gets the access permission to the command
line interface. Based on the user privileges, the help menu will be displayed to the user.
5.3.1 Main Group
When user logs in to the CLI it will lock to the default group which is the main
group.When ever the user enters the Main group,CLI will display the main
prompt .Help command in main group will show the commands supported in
main group along with the group lock commands. Only commands related to
main group can be executed in main group.
FullMax# main group
ipip-address
System IP address.
Command
FullMax# set ip-address

FullMax# show ipaddress
Purpose
Updates the system IP
address.
Displays the system IP
address.
Privileges
A/O
A/O
Example:
FullMax#set ip-address 10.60.4.42
Updated IP address: 10.60.4.42
FullMax# show ip-address
IP address: 10.60.4.56
Full Spectrum Confidential
92
FullMax BS100 and MS400 User Manual Version 1.1
5.3.2 ss-config
The ms-config group define the commands that monitors or updates the configuration
information. The user upon entering the ms-config command locks into the CLI to
execute commands only related to MS configuration.
FullMax#
FullMax# ss-config
FullMax(ss-config)#
Command
FullMax# ss-config
Purpose
The command allows the user to lock
into the group ss-config and execute
all the commands related to the group.
Privileges
A/O
The commands supported by the ss-config group are.
LostLost-dldl-mapmap-interval
Time since last received DL-MAP message before downlink synchronization is
considered lost in ms.
Command
FullMax(ss-config)# set
lost-dl-map-interval

FullMax(ss-config)# show
lost-dl-map-interval
Purpose
Privileges
The command allows the user to update A
timer value since last received DLMAP message before downlink
synchronization is considered lost.
The command allows the user to
A/O
display the timer value since last
received DL-MAP message before
downlink synchronization is considered
lost.
Example:
FullMax(ss-config) # set lost-dl-map-interval 300
Updated lost-dl-map-interval 300 milliseconds
FullMax (ss-config) # show lost-dl-map-interval
lost-dl-map-interval 300 milliseconds
LostLost-ulul-mapmap-interval
Time since last received UL-MAP message before downlink synchronization is
considered lost in ms.
Command
Purpose
Full Spectrum Confidential
Privileges
93
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(ss-config)# set
lost-ul-map-interval

FullMax(ss-config)# show
lost-ul-map-interval
The command allows the user to update
timer value since last received UL-MAP
message before downlink
synchronization is considered lost.
The command allows the user to display
the timer value since last received ULMAP message before downlink
synchronization is considered lost.
A/O
Example:
FullMax(ss-config)# set lost-ul-map-interval 300
Updated lost-ul-map-interval 300 milliseconds
FullMax(ss-config)# show lost-ul-map-interval
lost-ul-map-interval 300 milliseconds
ContentionContention-rngrng-retries
Number of retries on contention ranging requests.
Command
FullMax(ss-config)# set
contention-rng-retries

FullMax(ss-config)#show
contention-rng-retries
Purpose
The command allows the user to update
the contention ranging retries parameter.
Privileges
The command allows the user to display
the contention ranging retries parameter.
A/O
Example:
FullMax(ss-config)# set contention-rng-retries 20
Updated contention-rng-retries 20
FullMax(ss-config)# show contention-rng-retries
contention-rng-retries 20
RequestRequest-retries
Number of retries on bandwidth allocation request.
Command
FullMax(ss-config)# set
request-retries 
FullMax(ss-config)# show
request-retries
Purpose
Privileges
The command allows the user
to update the number of retries
on
bandwidth
allocation
request.
The command allows the user to
A/O
display the number of retries on
bandwidth allocation request.
Full Spectrum Confidential
94
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(ss-config)# set request-retries 88
Updated request-retries 88
FullMax(ss-config)# show request-retries
request-retries 88
RegReg-requsetrequset-retries
Number of retries on registration request.
Command
FullMax(ss-config)# set
reg-requset-retries 
FullMax(ss-config)# show
reg-requset-retries
Purpose
The command allows the user to
update the number of retries on
registration request.
The command allows the user to
display the number of retries on
registration request.
Privileges
A/O
Example:
FullMax(ss-config)# set reg-requset-retries 8
Updated reg-requset-retries 8
FullMax(ss-config)# show reg-requset-retries
reg-requset-retries 8
T1-timeout
Wait for DCD timeout in milliseconds.
Command
FullMax(ss-config)# set
t1-timeout 
FullMax(ss-config)# show
t1-timeout
Purpose
The command allows the user to
update the DCD timeout parameter.
The command allows the user to
display the DCD timeout parameter.
Privileges
A/O
Example:
FullMax(ss-config)# set t1-timeout 9000
Updated t1-timeout 9000 milliseconds.
FullMax(ss-config)# show t1-timeout
t1-timeout 9000 milliseconds.
T2T2-timeout
Wait for broadcast ranging timeout in milliseconds.
Full Spectrum Confidential
95
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(ss-config)# set
t2-timeout 
FullMax(ss-config)# show
t2-timeout
Purpose
Privileges
The command allows the user to update A
the broadcast ranging timeout
parameter
The command allows the user to
A/O
display the broadcast ranging timeout
parameter
Example:
FullMax(ss-config) # set t2-timeout 8000
Updated t2-timeout 8000 milliseconds.
FullMax(ss-config)# show t2-timeout
t2-timeout 8000 milliseconds.
T3T3-timeout
Ranging response reception timeout following the transmission of Ranging Request in
milliseconds.
Command
FullMax(ss-config)# set
t3-timeout 
FullMax(ss-config)# show
t3-timeout
Purpose
Privileges
The command allows the user to update A
the ranging response timeout
parameter.
The command allows the user to
A/O
display the ranging response timeout
parameter.
Example:
FullMax(ss-config)# set t3-timeout 45
Updated t3-timeout 45 milliseconds.
FullMax(ss-config)# show t3-timeout
T3-timeout 45 milliseconds.
T4T4-timeout
Wait for ranging opportunity or data grant. If pending until complete field was used
earlier by this SS, then the value of that field shall be added to this interval in second.
Command
FullMax(ss-config)# set
t4-timeout 
FullMax(ss-config)# show
t4-timeout
Purpose
The command allows the user to
update the wait for ranging
opportunity timeout parameter.
The command allows the user to
display the wait for ranging
opportunity timeout parameter.
Full Spectrum Confidential
Privileges
A/O
96
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(ss-config) # set t4-timeout 45
Updated t4-timeout 45 milliseconds.
FullMax(ss-config)# show t4-timeout
T4-timeout 45 milliseconds.
T16T16-timeout
Wait for Registration Response in milliseconds.
Command
FullMax(ss-config)#set
t16-timeout 
FullMax (ss-config)#show
t16-timeout
Purpose
Privileges
The command allows the user to
update the Registration response wait
timer.
The command allows the user to
A/O
display the Registration response wait
timer.
Example:
FullMax(ss-config)#set t16-timeout 540
Updated t16-timeout 540 milliseconds.
FullMax (ss-config) # show t16-timeout
T16-timeout 540 milliseconds.
T12T12-timeout
Wait for UCD descriptor in milliseconds.
Command
FullMax(ss-config)# set
t12-timeout 
FullMax(ss-config)# show
t12-timeout
Purpose
The command allows the user to
update wait for UCD descriptor
timer.
The command allows the user to
display the wait for UCD descriptor
timer.
Privileges
A/O
Example:
FullMax(ss-config) # set t12-timeout 12000
Updated t12-timeout 12000 milliseconds.
FullMax (ss-config) # show t12-timeout
t12-timeout 12000 milliseconds.
T18T18-timeout
Full Spectrum Confidential
97
FullMax BS100 and MS400 User Manual Version 1.1
Wait for SBC-RSP timeout in milliseconds.
Command
FullMax(ss-config)# set
t18-timeout 
FullMax(ss-config)# show
t18-timeout
Purpose
The command allows the user to
update wait for SBC-RSP timeout
parameter.
The command allows the user to
display the wait for SBC-RSP
timeout parameter.
Privileges
A/O
Example:
FullMax(ss-config) # set t18-timeout 7000
Updated t18-timeout 7000 milliseconds.
FullMax (ss-config) # show t18-timeout
t18-timeout 7000 milliseconds.
T19T19-timeout
Time DL-channel remains unusable in ms.
Command
FullMax(ss-config)#set
t19-timeout 
FullMax(ss-config)#show
t19-timeout
Purpose
Privileges
The command allows the user to
update time for DL-channel remains
unusable in ms..
The command allows the user to
A/O
display the time for DL-channel
remains unusable in ms.
Example:
FullMax(ss-config)# set t19-timeout 7000
Updated t19-timeout 7000 milliseconds.
FullMax(ss-config)# show t19-timeout
t19-timeout 7000 milliseconds.
T20T20-timeout
Time SS searches for preambles on a given channel in milliseconds.
Command
FullMax(ss-config)#set
t20-timeout 
FullMax(ss-config)#show
t20-timeout
Purpose
The command allows the user to update
the time to search for preambles on a
given channel.
The command allows the user to display
time to search for preambles on a given
channel.
Full Spectrum Confidential
Privileges
A/O
98
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(ss-config) # set t20-timeout 600
Updated t20-timeout 600 milliseconds.
FullMax (ss-config) # show t20-timeout
t20-timeout 600 milliseconds.
T21T21-timeout
Time SS searches for DL-MAP on a given channel in milliseconds.
Command
FullMax(ss-config)#set
t21-timeout 
FullMax(ss-config)#show
t21-timeout
Purpose
The command allows the user to update
the time to search for DL-MAP on a
given channel.
The command allows the user to display
time to search for DL-MAP on a given
channel.
Privileges
A/O
Example:
FullMax(ss-config)# set t21-timeout 1200
Updated t21-timeout 1200 milliseconds.
FullMax(ss-config)# show t21-timeout
t21-timeout 1200 milliseconds.
5.3.3 device
The device group define the commands that monitors or updates the device related
information in the private MIB. The user upon entering the device command locks into
the CLI to execute commands only related to device.
FullMax#
FullMax# device
FullMax(device)#
Command
FullMax#
Purpose
The command allows the user to lock into the
group device and execute all the commands
related to the group.
Privileges
A/O
type
Type of the device (BS / MS / SS).
Full Spectrum Confidential
99
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(device)#show
type
Purpose
The command allows the user display the
device type (BS/MS/SS)
Privileges
A/O
Example:
FullMax(device)# show type
type SS
gpos
The geographical position of the device ,
i.e. the real number describing the longitude and latitusde encoded as a printable string.
Longitude - the precision is within the range -90..90 degrees.Positive numbers indicate
locations north of the equator.
Latitude - The precision is within the range -180..180 degrees.Positive numbers indicate
locations east of the prime meridian
Command
FullMax(device)#set
gpos 
FullMax(device)#show
gpos
Purpose
The command allows the user to send the
command to the GPS avaliable on the
system.
The command allows the user display
geographical position of the device.
Privileges
A/O
Example:
FullMax(device)# set gpos 64.000 88.3400
updated gpos 64.000 88.3400
FullMax(device)# show gpos
gpos 64.000 88.3400
bootboot-time
The absolute time of last device boot up.
Command
FullMax(device)# show
boot-
Purpose
timeThe command allows the user
display the device boot up time.
Privileges
A/O
Example:
FullMax(device)# show boot-time
boot-time 230404:18052008
commitcommit-save
Setting this object to TRUE causes the device to write all configuration changes in
FLASH memory. On next boot the changes will be relevant. If this operation does not
occur, configuration changes will not be maintained through reset Reading this object
always returns FALSE
Full Spectrum Confidential
100
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(device)#set
commit-save 
FullMax(device)#show
commit-save
Purpose
The command allows the user to set the
value to TRUE so as to save the
configuration changes in FLASH.
The command allows the user display the
device commit-save
Privileges
A/O
Example:
FullMax(device)# set commit-save
commit-save TRUE
FullMax(device)# show commit-save
commit-save FALSE
gpsgps-card
GPS card availability in the device.
Command
FullMax(device)#show
gps-card
Purpose
The command allows the user display the
availability of GPS card in the device.
Privileges
A/O
Example:
FullMax(device)# show gps-card
gps-card YES
bpcbpc-hwhw-version
Hardware version of baseband processor card.
Command
FullMax(device)#show
bpc-hw-version
Purpose
The command allows the user display the
hardware version of baseband processor
card.
Privileges
A/O
Example:
FullMax(device)# show bpc-hw-version
bpc-hw-version 1.10
afeafe-hwhw-ver
Hardware version of the Analog Front End (AFE)
Command
FullMax(device)#show
afe-hw-ver
Purpose
The command allows the user display the
hardware version of AFE.
Full Spectrum Confidential
Privileges
A/O
101
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(device)# show afe-hw-ver
device-afe-hw-version 1.3
afeafe-swsw-ver
Software version of the Analog Front End (AFE)
Command
FullMax(device)#show
afe-sw-ver
Purpose
The command allows the user display the
software version of AFE.
Privileges
A/O
Example:
FullMax(device)# show afe-sw-ver
device-afe-sw-version 1.3
buildbuild-swsw-ver
Software version of the device general embedded software.
Command
FullMax(device)#show
build-sw-ver
Purpose
The command allows the user display the
software version of the software build
Privileges
A/O
Example:
FullMax(device)#show build-sw-ver
build-sw-version
5.3.4 Measurements
The Measurement group define the commands that monitors or updates the
measurement related information in the private MIB. The user upon entering the device
command locks into the CLI to execute commands only related to Measurement.
FullMax#
FullMax# measurement
FullMax(measurement)#
Command
FullMax#
measurement
Purpose
The command allows the user to lock into
the group Measurement and execute all the
commands related to this group.
Full Spectrum Confidential
Privileges
A/O
102
FullMax BS100 and MS400 User Manual Version 1.1
Temperature
Temperature degree in Celsius
Command
FullMax(measurement)#
show temperature
Purpose
The command allows the user display
temperature of the device.
Privileges
A/O
FullMax(measurement)#
track [-rN][-iN]
temperature
The command allows the user to display
real time temperature sample of the device.
A/O
Example:
FullMax(measurement)# show temperature
Temperature 45 degrees-Celsius
FullMax(measurement)# track –r3 –i2 temperature
Temperature 45 degrees-Celsius
Temperature 46 degrees-Celsius
Temperature 45 degrees-Celsius
Voltage
Voltage measurement
Command
FullMax(measurement)# show
voltage
Purpose
The command allows the user
display voltage of the device.
Privileges
A/O
FullMax(measurement)# track
[-rN][-iN] voltage
The command allows the user to
display multiple voltage samples of
the device.
A/O
Example:
FullMax(measurement)# show voltage
Voltage 3 volts
FullMax(measurement)# track –r3 –i10 voltage
Voltage 3 volts
Voltage 3 volts
Voltage 3 volts
Current
Current measurements
Command
FullMax(measurement)#show
current
FullMax(measurement)#track
Purpose
The command allows the user
display the current in the device.
Privileges
A/O
The command allows the user to
A/O
Full Spectrum Confidential
103
FullMax BS100 and MS400 User Manual Version 1.1
[-rN][-iN] current.
display multiple current
measurements in the device
Example:
FullMax(measurement)# show current
Current 2 amp
FullMax(measurement)# track –r4 current
Current 2 amp
Current 2 amp
Current 2 amp
TxTx-power
Transmit power
Command
FullMax(measurement)#show
tx-power
FullMax(measurement #track
[-rN][-iN] tx-power
Purpose
The command allows the user
display the transmit power.
The command allows the user to
display multple transmit power
measurements.
Privileges
A/O
A/O
Example:
FullMax(measurement)# show tx-power
Tx-power 45 dBm
FullMax(measurement)# track –r2 tx-power
Tx-power 45 dBm
Tx-power 43 dBm
RxRx-power
Receive power
Command
FullMax(measurement)#show
rx-power
FullMax(measurement)#track
[-rN][-iN] rx-power
Purpose
The command allows the user
display the receive power.
The command allows the user to
display multiple receive power
measurements.
Privileges
A/O
A/O
Example:
FullMax(measurement)# show rx-power
rx-power 45 dBm
FullMax(measurement)# track –r2 -i2 rx-power
rx-power 45 dBm
rx-power 45 dBm
Full Spectrum Confidential
104
FullMax BS100 and MS400 User Manual Version 1.1
afeafe-temperature
Read the temperature from the Analog Front End.
Command
FullMax(measurement)#show
afe-temperature
FullMax(measurement)#track
[-rN][-iN] afe-temperature
Purpose
The command allows the user
display temperatue from Analog
Front End.
The command allows the user to
display multiple temperatue
measurements from Analog Front
End
Privileges
A/O.
A/O
Example:
FullMax(measurement)# show afe-temperatue
afe-temperature 27 celcius
FullMax(measurement)# track -r4 -i30 afe-temperatue
afe-temperature 27 celcius
afe-temperature 27 celcius
afe-temperature 27 celcius
afe-temperature 27 celcius
afeafe-rssi
Read the Receive Signal Strength Indicator (RSSI) from the Analog Front End.
Command
Purpose
FullMax(measurement)#show
The command allows the user display
afe-rssi
RSSI from Analog Front End.
FullMax(measurement)#track The command allows the user to
[-rN][-iN] afe-rssi
display multiple RSSI measurements
from Analog Front End .
Privileges
A/O
A/O
Example:
FullMax(measurement)# show afe-rssi
afe-rssi 80 dBm
FullMax(measurement)# track -r4 -i30 afe-rssi
afe-rssi 80 dBm
afe-rssi 80 dBm
afe-rssi 80 dBm
afe-rssi 80 dBm
5.3.5 ss-private
The bs-private group define the commands that monitors or updates the private mib
related information. The user upon entering the ss-private command locks into the CLI to
execute commands only related to BS private mib.
FullMax#
Full Spectrum Confidential
105
FullMax BS100 and MS400 User Manual Version 1.1
FullMax# ss-private
FullMax(ss-private)#
Command
FullMax# ss-private
Purpose
The command allows the user to lock into
the group ss-private and execute all the
commands related to the group.
Privileges
A/O
ssss-rxrx-amcamc-countcount-table
This table contains statistical information that can be used to characterize the adaptive
modulation and coding performance in the uplink.
Command
FullMax(ss-private)#show
ss-rx-amc-count-table

Purpose
This command shows all the
parameters and their values for
RxAmcCountTable..
Privileges
A/O
Example:
FullMax(ss-private)# show ss-rx-amc-count-table 1
ss-rx-octets for diuc-index 1 is 0
ss-rx-packets for diuc-index 1 is 0
ss-tx-erroredpackets for diuc-index 1 is 0
ssss-rxrx-diucdiuc-index
The Downlink Interval Usage Code indicates the uplink burst profile in the UCD
message.
Command
FullMax(ss-private)# show
ss-rx-diuc-index
Example:
FullMax(ss-private)# show
ss-ul-diuc-index: 1
ss-ul-diuc-index: 2
ss-ul-diuc-index: 3
ss-ul-diuc-index: 4
ss-ul-diuc-index: 5
ss-ul-diuc-index: 6
ss-ul-diuc-index: 7
ss-ul-diuc-index: 8
ss-ul-diuc-index: 9
ss-ul-diuc-index: 10
Purpose
Privileges
This command allows the users to A/O
display the avaliable diuc-index
ss-rx-diuc-index
ssss-rxrx-octets
This object counts the number of octets received in the downlink using the downlink
burst profile indexed by diuc-index.
Full Spectrum Confidential
106
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(ss-private)#show
ss-rx-octets

Purpose
Privileges
This command allows the user to
display the number of octets
received in DL burst profile indexed
by diuc-index.
A/O
Example:
FullMax(ss-private)# show ss-rx-octets 1
ss-rx-octets for diuc-index 1 is 0
ssss-rxrx-packets
This object counts the number of packets received in the downlink using the downlink
burst profile indexed by
Command
FullMax(ss-private)#show
ss-rx-packets

Purpose
This Command allows the user to display
the number of packets received in DL
burst profile indexed by diuc-index
Privileges
A/O
Example:
FullMax(ss-private)#show ss-rx-packets 1
ss-rx-packets for diuc-index 1 is 0
ssss-rxrx-erroredPackets
Command
FullMax(ss-private)#show
ss-rx-erroredPackets

Purpose
This command allows the use rto
display the number of errored
packets indexed by diuc-index
Privileges
A/O
Example:
FullMax(ss-private)# show ss-rx-erroredPackets 1
ss-tx-errored packets for uiuc index 1 is 0
ssss-txtx-amcamc-countcount-table
This table contains statistical information that can be used to characterize the adaptive
modulation and coding performance in the downlink.
Command
FullMax(ss-private)#show
ss-tx-amc-count-table

Purpose
This command allows the user to
display the parametes and values of
the TxAmcCount Table.
Privileges
A/O
Example:
FullMax(ss-private)# show ss-tx-amc-count-table 1
ss-tx-octets for uiuc-index 1 is 0
Full Spectrum Confidential
107
FullMax BS100 and MS400 User Manual Version 1.1
ss-tx-packets for uiuc-index 1 is 0
ssss-txtx-uiucuiuc-index
The Uplink Interval Usage Code indicates the uplink burst profile in the UCD message.
Command
FullMax(ss-private)# show
ss-tx-uiuc-index
Purpose
This command allows the user to
display avaliable uiuc- indices
Privileges
A/O
Example:
FullMax(ss-private)# show ss-tx-uiuc-index
ss-dl-uiuc-index: 0
ss-dl-uiuc-index: 1
ss-dl-uiuc-index: 2
ss-dl-uiuc-index: 3
ss-dl-uiuc-index: 4
ss-dl-uiuc-index: 5
ss-dl-uiuc-index: 6
ss-dl-uiuc-index: 7
ss-dl-uiuc-index: 8
ss-dl-uiuc-index: 9
ss-dl-uiuc-index: 10
ss-dl-uiuc-index: 11
ss-dl-uiuc-index: 12
ssss-txtx-octets
This object counts the number of octets transmitted in the uplink using the uplink burst
profile indexed by uiuc-index
Command
FullMax(ss-private)#show
ss-tx-octets 
Purpose
This command allows the user to
display the Octets indexed by
uiuc-index.
Privileges
A/O
Example:
FullMax(ss-private)# show ss-tx-octets 1
ss-tx-octets for uiuc-index 1 is 0
ssss-txtx-packets
This object counts the number of packets transmitted in the uplink using the uplink burst
profile indexed by uiuc-index .
Command
FullMax(ss-private)#show
ss-tx-packets 
Purpose
This command allows the user to
display the packets in UL burst
indexed by uiuc-index
Full Spectrum Confidential
Privileges
A/O
108
FullMax BS100 and MS400 User Manual Version 1.1
Example:
FullMax(ss-private)# show ss-tx-packets 1
ss-tx-packets for uiuc-index 1 is 0
cmncmn-sfsf-table
This Table measures service flow traffic
Command
FullMax(ss-private)# show
cmn-sf-table 
Purpose
This command allows the user to
display the parameters and values
for cmn-sf-table for this SFID
Privileges
A/O
Example:
FullMax(ss-private)#show cmn-sf-table 2001
sf-total-octets for sfid 2001 is 0
sf-total-pkts for sfid 2001 is 0
sf-errored-pkts for sfid 2001 is 0
sf-frag-orig for sfid 2001 is 0
sf-frag-total for sfid 2001 is 0
sf-missing-frag for sfid 2001 is 0
cmncmn-pmpm-sfid
Command
FullMax(ss-private)#show
cmn-pm-sfid
Purpose
This command allows the user to
display the avlaibale SFID.
Privileges
A/O
Example:
FullMax(ss-private)# show cmn-pm-sfid
cmn-pm-sfid 2001
cmn-pm-sfid 2002
cmn-pm-sfid 3000
sfsf-totaltotal-octets
This determines the total octets received/transmitted on this service flow.
Command
FullMax(ss-private)#show
sf-total-octets 
Purpose
Privileges
This command allows the user to diplay
A/O
the total octets received or transmitted for
this service-flow.
Example:
FullMax(ss-private)# show sf-total-octets 2001
sf-total-octets for sfid (2001) : 1000
Full Spectrum Confidential
109
FullMax BS100 and MS400 User Manual Version 1.1
sfsf-totaltotal-pkts
This determines the total number of packets received /transmitted on this service flow.
Command
FullMax(ss-private)#show
sf-total-pkts 
Purpose
This Command allows the user to
display the total packets received
or trasmitted for this service-flow
Privileges
A/O
Example:
FullMax(bs-private)#show sf-total-pkts 2001
sf-total-pkts for sfid (2001): 22
sfsf-errorederrored-pkts
This determines number of packets that were dropped due to missing fragments / bad
ARQ blocks.
Command
FullMax(ss-private)#show
sf-errored-pkts 
Purpose
This Command Allows the user to
display the total errored packets
received or transmitted for this service
flow.
Privileges
A/O
Example:
FullMax(ss-private)# show sf-errored-pkts 2001
sf-errored-pkts for sfid (2001): 1
sfsf-fragfrag-orig
This determines number of fragments / ARQ blocks originally transmitted/received on
this service flow.
Command
FullMax(ss-private)#
show sf-frag-orig 
Purpose
This Command allows the user to
display the total fragments received
or transmitted originally on this
service flow.
Privileges
A/O
Example:
FullMax(ss-private)# show sf-frag-orig 2001
sf-frag-orig for sfid (2001) : 2
sfsf-fragfrag-total
This determines total fragments / ARQ blocks transmitted / received on this service
flow.
Full Spectrum Confidential
110
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(ss-private)# show
sf-frag-total 
Purpose
This Command allows the user to
display the total fragments
received or transmitted on this
service flow.
Example:
FullMax(ss-private)# show sf-frag-total
sf-frag-total for sfid (2001): 2
Privileges
A/O
2001
sfsf-missingmissing-frag
Description
This determines the number of missing received fragments received or NACK.
Command
FullMax(ss-private)# show
sf-missing-frag 
Purpose
This command allows the user to
display the number of missing
received fragments or NACK.
Privileges
A/O
Example:
FullMax(ss-private)# show sf-missing-frag 2001
sf-missing-frag for sfid (2001): 1
5.3.6 ss-chconfig
The ss-chconfig group define the commands that monitors or updates the channel config
MIB related information. The user upon entering(locking) the ss-chconfig group can
execute commands only related to ss-chconfig group.
FullMax#
FullMax# ss-chconfig
FullMax(ss-chconfig)#
Command
FullMax#ss-chconfig
Purpose
The command allows the user to lock into
the group ss-chconfig and execute all the
commands related to the group.
Privileges
A/O
ChannelChannel-configconfig-table
Each entry in the table contains optional channels configuration. A table can include a
single active channel configuration and some inactive channel configurations A MS
when searching for a new BS will scan the table for available channels.
Full Spectrum Confidential
111
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(ss-chconfig)#show
ss-channel-config-table

Purpose
The command allows the user
display the channel configuration
based on index. A/O
Privileges
A/O
Example:
FullMax(ss-chconfig)# show channel-config-table 1
center-channel-frequency for chn-index 1 is 12000
Hz
center-bandwidth for chn-index 1 is 120 Hz
center-config-status for chn-index 1 is ACTIVE
ChannelChannel-configconfig-index
Index in channel-config-table.
Command
FullMax(ss-chconfig)# show
channel-config-index
Purpose
Privileges
The command allows the user display A/O
all the channel configuration indices
Example:
FullMax(ss-chconfig)# show channel-config-index
Channel-config-index 1
Channel-config-index 2
CenterCenter-channelchannel-frequency
frequency
sets an optional center frequency for the transmitter and receiver Units are in Hz
Command
Purpose
Privileges
FullMax(ss-chconfig)# show The command allows the user display A/O
center-channel-frequency
center frequencies for the given

index.
Example:
FullMax(ss-chconfig)# show center-channel-frequency 1
center-channel-frequency for chn-index 1 16000 Hz
ChannelChannel-bandwidth
sets the bandwidth of the channel in the associated center frequency Units are in Hz.
Command
FullMax(ss-chconfig)#show
center-bandwidth

Purpose
Privileges
The command allows the user display A/O
bandwidth for the given index.
Example:
FullMax(ss-chconfig)# show center-bandwidth 2
Full Spectrum Confidential
112
FullMax BS100 and MS400 User Manual Version 1.1
center-bandwidth for chn-index 2 is 1600 Hz
samplingsampling-clock
The channel sampling clock
Command
FullMax(ss-chconfig)#show
sampling-clock 
Purpose
Privileges
The command allows the user display A/O
sampling clock time for the given
index.
Example:
FullMax(ss-chconfig)# show sampling-clock 2
sampling-clock for chn-index 2 is 16
filterfilter-id
The ID of the PHY filter to use for this channel.
Command
FullMax(ss-chconfig)#show
filter-id 
Purpose
Privileges
The command allows the user display A/O
filter id for the given index.
Example:
FullMax(ss-chconfig)# show filter-id 2
filter-id for chn-index 2 is 16
ChannelChannel-configconfig-status
Indicates the current state of this entry
inactiveOption(0) - indicates that this entry is a scanning option that is not currently in
use.
currentActive(1) - indicates that this entry is the current channel channel configuration
Command
FullMax(ss-chconfig)#show
channel-config-status 
Purpose
The command allows the user
display the current status for the
given index
Privileges
A/O
Example:
FullMax(ss-chconfig)# show channel-config-status 2
channel-config-status for chn-index 2 is ACTIVE
channelchannel-rowrow-status
This determines the row status of the Channel config table for this config-index.
Command
FullMax(ss-chconfig)#show
Purpose
The command allows the user
Full Spectrum Confidential
Privileges
A/O
113
FullMax BS100 and MS400 User Manual Version 1.1
channel-row-status
display the row status for the
given index
Example:
FullMax(ss-chconfig)# show channel-row-status 2
channel-row-status for chn-index 2 is ACTIVE
5.3.7 ss-trap
The trap-ctrl-register group defines the commands that monitors or updates the trap mib
related information. The user upon entering the trap-ctrl-register command locks into the
CLI to execute commands only related to BS and MS trap control register mib.
FullMax#
FullMax# ss-trap
FullMax (ss-trap) #
Command
FullMax# ss-trap
Purpose
The command allows the user to lock into
the group ss-trap and execute all the
commands related to the group
Privileges
A/O
Within this group we can get the following parameters.
SstrapControlRegister
PriTrapControlRegister.
ssss-traptrap-controlcontrol-register
The parameter is used to enable or disable the SS traps.
Command
FullMax(ss-trap)# set sstrap-control-register 
(enable or disable)
FullMax(ss-trap)#show sstrap-control-register
Purpose
The command allows the user to
enable or disable the SS traps
Privileges
The command allows the user
display the enable or disable
status of the SS traps.
A/O
Example:
FullMax(ss-trap)# set ss-trap-control-register 0
Updated ss-trap-control-register 0 (disable)
FullMax(ss-trap)# show ss-trap-control-register
ss-trap-control-register 0 (disable)
RssiRssi-lowlow-threshold
Low Rssi threshold for generating the RSSI alarm trap.
Full Spectrum Confidential
114
FullMax BS100 and MS400 User Manual Version 1.1
Command
FullMax(ss-trap)# set
rssi-low-threshold 
FullMax(ss-trap)#show
rssi-low-threshold
Purpose
The command allows the user to
update the lower threshold for
generating RSSI alaram trap
The command allows the user to
display the lower threshold for
generating RSSI alaram trap
Privileges
A/O
Example:
FullMax(ss-trap)# set rssi-low-threshold 34
Updated rssi-low-threshold 34 dBm
FullMax(ss-trap)# show rssi-low-threshold
rssi-low-threshold 34 dBm
RssiRssi-highhigh-threshold
High Rssi threshold for generating the RSSI alarm trap.
Command
Purpose
Privileges
FullMax(ss-trap)# set
The command allows the user to update A
rssi-high-threshold  the higher threshold for generating
RSSI alaram trap
FullMax(ss-trap)# show
The command allows the user to
A/O
rssi-high-threshold
display the higher threshold for
generating RSSI alaram trap.
Example:
FullMax(ss-trap)# set rssi-high-threshold 34
Updated rssi-high-threshold 54 dBm
FullMax(ss-trap)# show rssi-high-threshold
rssi-high-threshold 54 dBm
private-trap-ctrl
private
The object is used to enable or disable Base Station traps From left to right, the set bit
indicates the corresponding Base Station trap is enabled.
{ wmanPriPowerStatusChange (0), wmanPriFanStatusChange (1),
wmanPriTemperatureChange (2), wmanPriConfigChange (3),
wmanPriAfeBitError (4) }
Command
FullMax(ss-trap)#set
private-trap-ctrl 
Purpose
This command allows the user to
display the value of the private trap
control
Full Spectrum Confidential
Privileges
115
FullMax BS100 and MS400 User Manual Version 1.1
FullMax(ss-trap)#show
private-trap-ctrl
This command allows the user to
display the value of the private trap
control
A/O
Example:
FullMax(ss-trap)# set private-trap-ctrl 21
updated private-trap-ctrl
{ wmanPriPowerStatusChange(0),
wmanPriPowerStatusChange(2),
wmanPriPowerStatusChange(4)}
FullMax(ss-trap)# show private-trap-ctrl
private-trap-ctl enabled
{ wmanPriPowerStatusChange(0),
wmanPriPowerStatusChange(2),
wmanPriPowerStatusChange (4)}
Full Spectrum Confidential
116

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : kgrzovic
Create Date                     : 2010:03:10 11:30:40-07:00
Modify Date                     : 2010:03:10 11:31:09-07:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2010:03:10 11:31:09-07:00
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Format                          : application/pdf
Title                           : FCC Part 15
Creator                         : kgrzovic
Document ID                     : uuid:5a6fa310-3b15-4cbb-936b-5088600f335d
Instance ID                     : uuid:f3e94d66-38f6-44cf-b65e-035491d5f064
Producer                        : Adobe PDF Library 9.0
Page Count                      : 117

EXIF Metadata provided by EXIF.tools