Option OMO0201 GSM/GPRS/UMTS/HSDPA QUAD BAND PCI MINI CARD User Manual Z06 131 GTM kit 353W QS v2 indd

Download:
Mirror Download [FCC.gov]
Document ID	1014362
Application ID	lgqtGDI8JuOTgNdrwSYrBw==
Document Description	User Manual Quick Start Guide II
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	199.36kB (2492039 bits)
Date Submitted	2008-10-14 00:00:00
Date Available	2007-01-24 00:00:00
Creation Date	2007-01-24 15:39:16
Producing Software	Adobe PDF Library 6.0
Document Lastmod	2007-01-24 15:39:35
Document Title	Z06.131_GTM_kit_353W_QS_v2.indd
Document Creator	Adobe InDesign CS (3.0.1)

PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
15 of 30
(7) When you launch the GT connect application it looks like Figure 22. For detailed application
description and usage, refer to the release notes on the CD-ROM provided with the package.
Figure 22: GT Connect application
With this application you can easily connect to the internet.
(8) To close GT Connect completely, go with your mouse pointer to the title bar and choose
“Exit” from the context menu.
[ OPTION CONFIDENTIAL ]
Figure 23: Exit GT Connect
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
16 of 30
HYPERTERMINAL
This section describes briefly how to setup HyperTerminal to communicate with the PCI
Express Mini Card by AT commands.
(1) Go to device manager, and check which port is the Application port.
In this example, the application port is COM6. It also important to know is that GT Connect
takes hold of the Application port. So before going any further, exit GT Connect completely.
Refer to the previous chapter.
Figure 24: Device manager
To get to device manager go to “Start” menu and select “Run”. In the next dialogue type
[ OPTION CONFIDENTIAL ]
“devmgmt.msc” as shown on the next screenshot:
Figure 25: Run to device manager
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
17 of 30
(2) Open HyperTerminal with the “Start” menu in Windows:
Start > Programs > accessories > Communication > HyperTerminal
(3) Normally, you have to do the following two steps only once. If you already have done so
in the past you can skip to step 5. If not, choose a country and an area code. For use with the
module, it does not matter, so just enter anything.
Figure 26: Location information
[ OPTION CONFIDENTIAL ]
(4) Just “OK” the next “Phone and Modem Options” screen.
Figure 27: Phone and Modem Options
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
18 of 30
(5) Enter a name for your HyperTerminal Connection and press OK.
Figure 28: Location information
(6) In the next window, change the “Connect using:” field to the Application Port
(COM6 in this example). Click OK.
[ OPTION CONFIDENTIAL ]
Figure 29: Phone and Modem Options
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
19 of 30
(7) Now the next window will appear. Modify the Bit per second field to 115200 and click OK.
Figure 30: Connection Properties
HyperTerminal is configured and you are now ready issue AT commands to the PCI Express
Mini Card module. Figure 31 shows a typical HyperTerminal session. If you don’t have visual
feedback of what you are typing, you need to turn echo on by typing ATE1 followed by enter
[ OPTION CONFIDENTIAL ]
first as shown in below example.
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
20 of 30
Figure 31: Typical HyperTerminal session
When you close HyperTerminal, you have the opportunity to save your HyperTerminal profile.
Saved profiles can be found under Start > Programs > accessories > Communication
[ OPTION CONFIDENTIAL ]
> HyperTerminal
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
21 of 30
SET UP A DATA CALL
Besides using dashboard applications, it is also possible to set up a data call using
windows dial-up networking.
This section explains how to set up a dial-up connection.
(1) Go to Start > Control Panel > Network Connections and click on the icon “New
Connection Wizard”. The next screen will appear:
Figure 32: Network connections
(2) Click ‘Next’ and Figure 33 will appear. Select “Connect to the Internet” and click
[ OPTION CONFIDENTIAL ]
“Next” again. Now Figure 34 will appear.
Figure 33: New network connection
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
22 of 30
Figure 34: Manual connection setup
(3) Select “Set up the connection manually”, and click the “Next” button.
Choose the “Connect using a dial-up modem” option, and click the “Next” button.
[ OPTION CONFIDENTIAL ]
Figure 35: Connection with dial-up modem
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
23 of 30
(4) Select the correct modem (Modem - Globetrotter 3G+ modem interface), and
click the ‘Next’ button.
Figure 36: Select modem
(5) Type a name for the connection, which you will select the next time you need this
dial-up connection, and click the ‘Next’ button.
[ OPTION CONFIDENTIAL ]
Figure 37: Connection Name
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
24 of 30
(6) Type in the Phone number to dial, which is *99#, and click the ‘Next’ button.
Figure 38: Number to dial
(7) Choose the option you like, and then click the ‘Next’ button.
[ OPTION CONFIDENTIAL ]
Figure 39: Connection availability
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
25 of 30
(8) If your service provider requests to enter username and password for setting up a
PS data call connection, please enter it using the screen below.
Figure 40: Internet Account Information
(9) The connection is set up and ready to use. Click the ‘Finish’ button to close the
wizard.
[ OPTION CONFIDENTIAL ]
Figure 41: Connection complete
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
26 of 30
(10) Before attempting to make the dial-up connection, make sure you are registered
to the network. Observe that the Registration LED in Figure 1 is on. Also, the APN for
your operator should be set correctly in the module. This can be done with
the following AT command:
AT+CGDCONT=1,,”your APN here”
You have to set this command only once for each module as this setting is stored in
non-volatile memory of the module. Use the explanation from the previous chapter
on how to use HyperTerminal to send AT commands.
To verify the APN setting just type: AT+CGDCONT?
(11) Then, if your module is registered on the network, you can use the above
configured dial-up connection to activate a PDP context and make an internet
connection.
[ OPTION CONFIDENTIAL ]
Go to Start > Connect to > “Module PDP” and select it.
Figure 42: Connect Module PDP
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
27 of 30
(12) Click the Dial button. After a while, a connection to the internet is made.
Figure 43: Connecting Module PDP
Figure 44: Module PDP is now connected
To disconnect, go to the appropriate network systray icon and select “Disconnect”
from the context menu (right mouse button).
[ OPTION CONFIDENTIAL ]
Figure 45: Disconnect Module PDP
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
28 of 30
9 SET UP A VOICE CALL
Remark! This section is only applicable for GTM378 and GTM353 (Hardware version
3.1 or later).
Verify below AT commands in order to set-up the module for voice calls. Refer to
Chapter 7 on how to send AT commands to the module using HyperTerminal.
First of all make sure your PIN code is entered and that you are registered to the
network. Observe the Registration LED on Figure 1.
• AT_ODO=0
With this AT command circuit switched data transfer, which is needed for voice
calls, is enabled. This setting is stored in non-volatile memory on the module.
The response on this AT command should be: OK
• AT_OPCMENABLE=1
Per default, the voice part of the firmware is disabled. To enable digital voice, the
command above must be set. This setting is stored in non-volatile memory on the
module.
The response on this AT command should be: OK
• AT_OPCMCONFIG=102,3,0,256,0,1,4
This AT command configures the PCM codec for 16bit linear with volume
padding, maximum volume (Short Synch 8kHz, 2MHz CLK). This is also the default
configuration. NOTE: In this configuration the jumper in the upper right corner
should be set to the two most right pins (see Figure 1). This setting is stored in
non-volatile memory on the module.
The response on this AT command should be: OK
OR
• AT_OPCMCONFIG=0,0,0,256,0,1,4
This AT command configures the PCM codec for 8bit Ulaw, maximum volume
(Short Synch 8kHz, 2MHz CLK). NOTE: In this configuration the jumper in the upper
right corner should be set to the two most left pins (see Figure 1). This setting is
[ OPTION CONFIDENTIAL ]
stored in non-volatile memory on the module.
The response on this AT command should be: OK
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
29 of 30
• ATD;
To set-up the call, the ATD command followed by a phone number must be used.
NOTE: Do not forget the semicolon (;) at the end of the AT command!!!
The response on this AT command should be: OK
Now the phone on the other side should answer the paging and a voice
conversation can be made. To stop the conversation to other side can simply hangup the phone and a “NO CARRIER” string is displayed in HyperTerminal. If you want
to end the call from your side you can type ATH, followed by an OK. The next figure
shows an example voice call set-up and termination.
[ OPTION CONFIDENTIAL ]
Figure 46: Voice call set-up
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3
PAGE :
GLO B ET R OT T ER Q UIC K S TA R T G UID E
30 of 30
REFERENCES
Document
Integration Manual
[ OPTION CONFIDENTIAL ]
Ref
AUTHOR : G. Van Overbeke
CREATION DATE :
Aug 8, 2006 |
VERSION :
v01-f3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Modify Date                     : 2007:01:24 15:39:35+01:00
Create Date                     : 2007:01:24 15:39:16+01:00
Metadata Date                   : 2007:01:24 15:39:35+01:00
Creator Tool                    : Adobe InDesign CS (3.0.1)
Format                          : application/pdf
Title                           : Z06.131_GTM_kit_353W_QS_v2.indd
Document ID                     : uuid:88ffa6ef-388f-4b46-851a-d3ce1909a946
Instance ID                     : uuid:3720d59b-6d0c-4ccc-af83-43d899ed36b6
Producer                        : Adobe PDF Library 6.0
Page Count                      : 16
Creator                         : Adobe InDesign CS (3.0.1)

EXIF Metadata provided by EXIF.tools