Orion Electric Co F7T765 17 Inches Color Monitor User Manual

Orion Electric Co Ltd 17 Inches Color Monitor

User Manual

1 INSTRUCTION MANUALCONTENTSSAFETY INSTRUCTION 2 CAUTIONS 4 FCC RF INTERFERENCE STATEMENT 5 INSTALLATION 6 RESOLUTION 7 CONTROLS AND FUNCTIONS 8 REAR VIEW 13 SPECIFICATIONS 14 TROUBLE SHOOTING GUIDE 15 WICHTIGE HINWEISE (GERMAN) 16 This Monitor wasManufactured by ISO 9001Certified Factory
INSTRUCTION MANUAL 2SAFETY INSTRUCTION1. Read all of these instructions.2. Save these instructions for later use.3. Follow all warnings and instructions marked on the product.4. Unplug this product from the wall outlet before cleaning.Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.5. Do not use this product near water.6. Do not place this product on an unstable cart, stand or table.The product may fall, causing serious damage to the product.7. Slots and openings in the cabinet and the back or bottom are provided forventilation: to ensure reliable operation of the product and to protect it fromoverheating these openings must not be blocked by placing the product on a bed,sofa, rug or other similar surface. This product should not be placed near or overa heat register.This product should not be placed in a built-in installation unless proper ventilationis provided.8. This product should be operated from the type of power source indicated on themarking label. If you are not sure of the type of power available, consult your dealeror local power company.9. This product is equipped with a 3 wire grounding type plug having a third(grounding)pin. This is a safety feature. If you are unable to insert the plug into the outlet,contact your electrician to replace your obsolete outlet. Do not defeat the purpose ofthe grounding-type plug.10. Do not allow anything to rest on the power cord.Do not locate this product where persons will walk on the cord.11. If an extension cord is used with this product, make sure that the total of theampere ratings on the products plugged into the extension cord do not exceed theextension cord ampere rating. Also, make sure that the total of all productsplugged into the wall outlet does not exceed 10 amperes.12. Never push objects of any kind into this product through cabinet slots as they maytouch dangerous voltage points or short out parts that could result in a risk of fireor electric shock. Never spill any kind of liquid on the product.
3 INSTRUCTION MANUALSAFETY INSTRUCTIONCAUTION TO SERVICE PERSONNELPOWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE INTHIS PRODUCT. UNPLUG THIS PRODUCT FROM THE WALL OUTLETBEFORE REMOVING THE BACK COVER AND SERVICINGEMISSION CHARACTERISTICS TESTED BY SEMKOTHIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITHTHE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990.10.(MPR )13. Do not attempt to service this product yourself, as opening or removing coversmay expose you to dangerous voltage points or other risks.Refer all servicing to service personnel.14. Unplug this product from the wall outlet and refer servicing to qualified servicepersonnel under the following conditions.A. When the power cord or plug is damaged or frayed.B. If liquid has been spilled into the product.C. If the product has been exposed to rain or water.D. If the Product does not operate normally when the operating instructions arefollowed. Adjust only those controls that are covered by the operatinginstructions since improper adjustment of other controls may result in damageand will often require extensive work by a qualified technician to restore normaloperation.E. If the product has been dropped or the cabinet has been damaged.F. If the product exhibits a distinct change in performance, indicating a need forservice.CCCCAAAAUUUUTTTTIIIIOOOONNNNThe power supply cord is used as the main disconnect device, ensure that thesocket-outlet is located/installed near the equipment and is easily accessible.AAAATTTTTTTTEEEENNNNTTTTIIIIOOOONNNNLe cordon d`alimentation est utillsé comme interrupteur général. La prise decourant doit être située ou installée à proximité du matériel et être faciled`accès
INSTRUCTION MANUAL 4CAUTIONSNEVER REMOVE THE BACK COVERNEVER REMOVE THE BACK COVERRemoval of the back cover should be carried out only by qualified personnel.This display monitor contains high voltage inside.DO NOT USE IN HOSTILE ENVIRONMENTSDO NOT USE IN HOSTILE ENVIRONMENTSTo prevent shock or fire hazard. Do not expose the unit to rain or moisture.This unit is designed to be used in the office or home. Do not subject the unit tovibrations, dust of corrosive gases.KEEP IN A WELL VENTILATED PLACEKEEP IN A WELL VENTILATED PLACEVentilation holes are provided on the cabinet to prevent the temperature fromrising.Do not cover the unit or place anything on the top of unit. Ventilation holes areprovided also on the bottom of the cabinet.AVOID HEATAVOID HEATAvoid placing the unit in direct sunshine or near a heating appliance.BE CAREFUL OF MAGNETIC FIELDSBE CAREFUL OF MAGNETIC FIELDSDo not place a magnet, speaker system, floppy disc drive or anything which willgenerate magnetism near the unit, A magnetic field may cause blurred colors ordistortion of the displayed pattern.TO ELIMINATE EYE FATIGUETO ELIMINATE EYE FATIGUEDo not use the unit against a bright back ground and where sunlight or other lightsources will shine directly on the monitor.BE CAREFUL OF HEAVY OBJECTBE CAREFUL OF HEAVY OBJECTNeither the monitor itself nor any other heavy object should rest on the power cord.Damage to a power cord can cause fire or electrical shock.
5 INSTRUCTION MANUALFCC RFINTERFERENCE STATEMENTNNNNOOOOTTTTEEEE ::::This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation.This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or televisionreception which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the followingmeasures.- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.- Consult the dealer or an experienced radio, TV technician for help. - Only shielded interface cable should be used.Finally, any changes or modifications to the equipment by the user notexpressly approved by the grantee or manufacturer could void the usersauthority to operate such equipment.DOC COMPLIANCE NOTICEThis digital apparatus does not exceed the Class B limits for radio noise emissionsfrom digital apparatus set out in the radio interference regulation of CanadianDepartment of Communications.AVIS DE CONFORMATION AU MDC(DOC)Le présent appareil numérique n´émet pas de bruits radio-électriques dépassant leslimites appliqués aux appareils numériques de Class B d´après les règlements surle brouillage radio-électrique conçuent par le ministère des communications duCanada.
NO TOOLS ARE REQUIRED TO INSTALL THE MONITOR.SIMPLY FOLLOW THE INSTRUCTIONS OUTLINED IN THE FOLLOWING PAGE.1. INSTALLING THE TILT/SWIVEL STAND1) Align the stand with the front slots in the bottom of the monitor and insert theTilt/Swivel Stand into the slots.2) Push the Tilt/Swivel Stand firmly toward the front of the monitor until the latchesclick into the locked position.2. CONNECT THE SIGNAL CABLE1) Connect the end into the graphic card on back of the computer.2) Secure the connection with the screws on the plug.3. CONNECT THE POWER CORDConnect the female end of the power cord to the power inputreceptacle on the back panel of the monitor.Then, plug the male end of the power cord to an AC outlet or computer.4. TURN THIS MONITOR ON AND START YOUR SYSTEMINSTRUCTION MANUAL 6INSTALLATIONHook122
INSTRUCTION MANUAL 8A. POWER ON/OFF( )Turns the power ON or OFF. There will be a few seconds delay beforethe display appears.The power LED(next to the power switch) lights when the poweris turned ON.The power is turned off by pressing the power switch again andthe power LED goes out.B. MENUActivates and exits the On Screen Display. This button can also beused to move previous menu or status.There are two OSD menu or status.They are MAIN MENU1 (H.POSITION, H.SIZE, V.POSITION, V.SIZE,PINCUSHION, TRAPEZOID, PARALLELOGRAM,PINBALANCE, CORNER CORRECTION, COLOR-TEMP, BRIGHTNESS, CONTRAST) MAIN MENU2 (RECALL, ROTATION, LANGUAGE, DEGAUSS,OSD H.POSITION, OSD V.POSITION, OSD ON TIME,VIDEO LEVEL, MOIRE, INFORMATION, EXIT)CONTROLS AND FUNCTIONSB. MENU BUTTOND. ADJUST BUTTONS(DOWN & UP)C. SELECT BUTTON POWER INDICATOR(LED)A. POWER SWITCH
9 INSTRUCTION MANUALCONTROLS AND FUNCTIONSC. SELECTThe select button allows user to activate the desired adjustmentwith blinking icon.D. ADJUST ( , )The Adjust button allows user to choose the icons (controls) in the menu.Pressing the adjust button or will step through all availableadjustment icons (controls).In addition this adjust button can be used to adjust the icons (dot controls)that is selected and activated (blinking) via the select button. When the adjust buttonis pressed, The adjustment bar in the window will be increased or decreased.After completing all the desired adjustments, the On Screen Displaywill disappear with pressing the menu button.1. SELF-TEST DISPLAYWhen there is no connection, the On Screen Displaywill show.MAIN MENU 1 activates when you press the Menu button.MAIN MENU 2 activates when you press () at the CONTRAST(EXIT) icon in the menu1.NO SIGNALCHECK SIGNAL CABLE
INSTRUCTION MANUAL 10CONTROLS AND FUNCTIONS2. AUTO REGISTRATIONThis monitor has 10 preset modes. If the current video is one of thepreset modes, the monitor keeps storing the custom display settingsinto the permanent memory.There are also 10 user modes that allow you to save the custom displaysettings made to any video mode that is not one of the preset modes.Adjustments are automatically registered without pressing any buttons.Up to 10 user modes are stored automatically on a “First-In-First-Out”basis.3. OSD MENU DESCRIPTIONMAIN MENU 1H. POSITION (Horizontal Position)Moves images horizontally on screen left( ) or right( ).H. SIZE (Horizontal Size)Increases( ) or decreases( ) Size of image horizontally.V. POSITION (Vertical Position)Moves images vertically on screen up( ) or down( ).V. SIZE (Vertical Size)Increases( ) or decreases( ) Size of image vertically.PINCUSHIONAdjusts the side Pincushion or barrelling.TRAPEZOIDAdjusts the display sides to be parallel.PARALLELOGRAMAdjusts the tilt of the display sides.PINBALANCEAdjusts the curvature of the left and right sides of the screen image.
11 INSTRUCTION MANUALCONTROLS AND FUNCTIONSCORNER CORRECTIONUser can select Top or Bottom Corner correction by pressingthe Select button.TOP CORNER CORRECTIONCorrects the top corner image shape to a rectangle.BOTTOM CORNER CORRECTIONCorrects the bottom corner image shape to a rectangle.COLOR-TEMPAdjusts color temperature to 9300K, 6500K(notes : 9300K is factory default).Or, for a custom color mode, select “USER” and keep pressing select key approximately 2 seconds to activate the RGB Sub-menu.This adjust the intensity of the RGB video output. Using the select buttonactivate(blinking) the R-GAIN(Red Gain), G-GAIN(Green Gain) or B-GAIN(Blue Gain) and change color strength for a customized color mode.BRIGHTNESSIncreases( ) or decreases( ) the intensity(illumination) of the image.CONTRASTIncreases( ) or decreases( ) the strength(lightness or dimness)of the image.MAIN MENU 2RECALLResets the control functions back to the original factory preset values.In order for the Recall function working, the timing must fall under oneof the factory preset timing modes.ROTATIONAdjusts the tilt of image.LANGUAGESelects a language among ENGLISH, DEUTSCH, FRANÇAIS, ESPAÑOL, (JAPANESE).DEGAUSSManually demagnetizes the CDT. This can be used if the displaybecomes discolored.Allow a minimum of 20 minutes to elapse between each degauss.The monitor also will automatically degauss when power is applied, and power saving mode is changed to normal mode.
OSD H.POSITIONMoves the OSD position to left or right.OSD V.POSITIONMoves the OSD position to up or down.OSD ON TIMEIf there isn’t key pressure OSD will be disappeared automatically the setted seconds later.VIDEO LEVELSelects the video level of the Video Graphic Card.If the intensity of image is high select 1.0V & if low select 0.7V.MOIREAdjusts the moire level of the screen.H. MOIRE ADJUSTReduces the optical effect of horizontal wavy lines on the display image.These effects are usually more noticeable on large gray areas or on black & white check board patterns.V. MOIRE ADJUSTReduces the optical effect of vertical wavy lines on the display image. These effects are usually more noticeable on large gray areas or on black & white check board patterns.INFORMATIONDisplays the current mode, horizontal frequency, vertical frequency,the factory preset mode and user preset mode.EXITExit user menu.INSTRUCTION MANUAL 12CONTROLS AND FUNCTIONS
13 INSTRUCTION MANUALREAR VIEWE. AC INLETPower cord connection.NNOOTTEE::Power cord is used as main power disconnect device in this product.F. D-SUB CONNECTOR OF SIGNAL CABLEConnect to the analog RGB signal output connector of IBM PS/2, or compatible computer.ACCESSORY1. POWER CORD2. INSTRUCTION MANUALE. AC INLET F. D-SUB CONNECTOROF SIGNAL CABLE
SPECIFICATIONSINSTRUCTION MANUAL 14PICTURE TUBE17 (16V) Flat CDTDot Type 0.25mm Pitch Black Matrix Screen High resolution screenDark Faceplate Glass High contrast screen90 Deflection and 29.1mm Diameter Neck Lower power consumption16 Visual Screen Diagonal Full-square type screenAnti-Static Charge Face Electro static charge eliminatedHi-view(Silica coat, Anti-Glare, Anti-Reflection) Surface Glare problem eliminatedInvar Shadow Mask.INPUT SIGNALD-SUB INPUTAnalog RGB Video: 0.7Vpp / 75Sync.: TTL LevelSWEEP FREQUENCYHorizontal: 30-70KHz(Automatically)Vertical: 50-150Hz(Automatically)DISPLAY AREA(16 Viewable Size)Full Size: 326 x 245mmPreset Size: 305 x 225mmPOWER INPUTAC 100-240V, 50/60Hz, 1.6-0.8A (FREE VOLTAGE)POWER CONSUMPTION85Watts(Max.)Power Saving: Less than 5WDimensions (W x D x H)399mm X 411mm X 394mmWEIGHTNet Weight : 16.0Kg Gross Weight : 18.5KgRESOLUTION1280 dots x 1024 lines(Max.)DDC 1/2BOSD(On Screen Display)NNOOTTEE ::Technical specifications are subject to change without notice.
15 INSTRUCTION MANUALTROUBLE SHOOTING GUIDEThe video card should be completelyseated in its slot.Power switch and computer power switch shouldbe in the ON position.The signal cable should be completely connectedto the video card/computer.Check connector for bent or pushed-in pins.Power switch should be in the ON position and thepower cord should be connected.Adjust size and position controls to adjust theimage.Wait approximately ten seconds after makingadjustments before changing or disconnection thesignal or powering OFF the monitor.Signal cable should be completely attached to thecomputer.Check the pin assignments and signal timmings ofthe monitor and your video card.Move electrical that may be causing electricalinterference away from the monitor.Adjust the side pin-cushion control.PROBLEM CHECK THESE ITEMSNo Picture(Not in power saving mode)LED on the monitor is not litDisplay image is notcentered, too small or too largeDisplay size and positionwere not savedImage is scrolling orunstablePicture bounces or a wavepattern is present inthe pictureEdges of the display imageare curved either inwardor outward

Navigation menu