Orion Electric Co LA530SH 15" LCD Monitor User Manual

Orion Electric Co Ltd 15" LCD Monitor

User Manual

1INSTRUCTION MANUALCONTENTSSAFETY INSTRUCTION 2 CAUTIONS 4 FCC RF INTERFERENCE STATEMENT 5 CONNECTING WITH EXTERNAL EQUIPMENT 6 RESOLUTION 7 CONTROLS AND FUNCTIONS 8 REAR VIEW 13 D-SUB CONNECTOR PIN ASSIGNMENTS 14 POWER MANAGEMENT 15 SPECIFICATIONS 16 TROUBLESHOOTING GUIDE 17 WICHTIGE HINWEISE (GERMAN) 18 This Monitor wasManufactured by ISO 9001Certified Factory
INSTRUCTION MANUAL 2SAFETY INSTRUCTION1. Read all of these instructions.2. Save these instructions for later use.3. Follow all warnings and instructions marked on the product.4. Unplug this product from the wall outlet before cleaning.Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.5. Do not use this product near water.6. Do not place this product on an unstable cart, stand or table.The product may fall, causing serious damage to the product.7. Slots and openings in the cabinet and the back are provided forventilation: to ensure reliable operation of the product, these openingsmust not be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a heat register.This product should not be placed in a built-in installation unless proper ventilationis provided.8. This product should be operated from the type of power source indicated on themarking label. If you are not sure of the type of power available, consult your dealeror local power company.9. This product is equipped with a 3 wire grounding type plug having a third(grounding)pin. This is a safety feature. If you are unable to insert the plug into the outlet,contact your electrician to replace your obsolete outlet. Do not defeat the purpose ofthe grounding-type plug.10. Do not allow anything to rest on the power cord.Do not locate this product where persons will walk on the cord.11. If an extension cord is used with this product, make sure that the total of theampere ratings on the products plugged into the extension cord do not exceed theextension cord ampere rating. Also, make sure that the total of all productsplugged into the wall outlet does not exceed 10 amperes.12. Never push objects of any kind into this product through cabinet slots as they maytouch dangerous voltage points or short out parts that could result in a risk of fireor electric shock. Never spill any kind of liquid on the product.13. Do not attempt to service this product yourself, as opening or removing coversmay expose you to dangerous voltage points or other risks.Refer all servicing to service personnel.
3 INSTRUCTION MANUALSAFETY INSTRUCTION14. Unplug this product from the wall outlet and refer servicing to qualified servicepersonnel under the following conditions.A. When the power cord or plug is damaged or frayed.B. If liquid has been spilled into the product.C. If the product has been exposed to rain or water.D. If the Product does not operate normally when the operating instructions arefollowed. Adjust only those controls that are covered by the operatinginstructions since improper adjustment of other controls may result in damageand will often require extensive work by a qualified technician to restore normaloperation.E. If the product has been dropped or the cabinet has been damaged.F. If the product exhibits a distinct change in performance, indicating a need forservice.CCCCAAAAUUUUTTTTIIIIOOOONNNNThe power supply cord is used as the main disconnect device, ensure that thesocket-outlet is located/installed near the equipment and is easily accessible.AAAATTTTTTTTEEEENNNNTTTTIIIIOOOONNNNLe cordon d`alimentation est utillsé comme interrupteur général. La prise decourant doit être située ou installée à proximité du matériel et être faciled`accèsCAUTION TO SERVICE PERSONNELPOWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE INTHIS PRODUCT. UNPLUG THIS PRODUCT FROM THE WALL OUTLETBEFORE REMOVING THE BACK COVER AND SERVICINGEMISSION CHARACTERISTICS TESTED BY SEMKOTHIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITHTHE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990.10.(MPR )
INSTRUCTION MANUAL 4CAUTIONSNEVER REMOVE THE BACK COVERRemoval of the back cover should be carried out only by qualified personnel.DO NOT USE IN HOSTILE ENVIRONMENTSTo prevent shock or fire hazard, do not expose the unit to rain or moisture.This unit is designed to be used in the office or home. Do not subject the unit tovibrations, dust of corrosive gases.KEEP IN A WELL VENTILATED PLACEVentilation holes are provided on the cabinet to prevent the temperature fromrising.Do not cover the unit or place anything on the top of unit. AVOID HEATAvoid placing the unit in direct sunshine or near a heating appliance.TO ELIMINATE EYE FATIGUEDo not use the unit against a bright back ground and where sunlight or other lightsources will shine directly on the monitor.BE CAREFUL OF HEAVY OBJECTNeither the monitor itself nor any other heavy object should rest on the power cord.Damage to a power cord can cause fire or electrical shock.
5 INSTRUCTION MANUALFCC RFINTERFERENCE STATEMENTNNNNOOOOTTTTEEEE ::::This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation.This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or televisionreception which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the followingmeasures.- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.- Consult the dealer or an experienced radio, TV technician for help. - Only shielded interface cable should be used.Finally, any changes or modifications to the equipment by the user notexpressly approved by the grantee or manufacturer could void the usersauthority to operate such equipment.DOC COMPLIANCE NOTICEThis digital apparatus does not exceed the Class B limits for radio noise emissionsfrom digital apparatus set out in the radio interference regulation of CanadianDepartment of Communications.AVIS DE CONFORMATION AU MDC(DOC)Le presént appareil numérique n`émet pas de bruits radio-électriques dépassant leslimites appliqués aux appareils numériques de Class B d´arès les règlement sur lebrouillage radio-électrique conçuent par le ministère des communications du Canada.
INSTRUCTION MANUAL 6CONNECTING WITH EXTERNALEQUIPMENTCCCCAAAAUUUUTTTTIIIIOOOONNNNBe sure to turn off the power of your computer before connecting the monitor.1. CONNECT THE VIDEO SIGNAL CABLEA. Connect one end of the signal cable to the back panel of the monitor and connect the other end to the graphic card on back of the computer.B. Secure the connection with the screws on the plug.2. CONNECT THE POWER CORDA. Connect the plug of the AC/DC adaptor to the monitor.B. Connect the female end of the power cord to the power inputreceptacle on the AC/DC adaptor .Then, plug the male end of the power cord to an AC outlet or computer.3. TURN THIS MONITOR ON AND START YOUR SYSTEM
640 350 31.5 70720 400 31.5 70640 480 31.5 60640 480 35.0 67800 600 37.8 601024 768 48.3 60RESOLUTION FREQUENCYH(Pixels) V(Lines) H(KHz) V(Hz)PRESET MODESVGAMACVESA7 INSTRUCTION MANUALRESOLUTIONThis monitor is a digitally-controlled multi-frequency monitor.It operates at horizontal frequencies of 31 to 60KHz and verticalfrequencies of 56 to 75Hz.Because of its micro processor-based designs it offers auto-synchronizationand auto-sizing capabilities. This monitor offers 6 programmed settingsas listed in the table below.And designs its best quality at 1024X768, 48KHz@60Hz.Sometimes, displayed image quality couldn’t be good enough in other modes because of TFT-LCD Monitor’s basic characteristics.To enjoy the best quality, change the mode; click the right mouse botton anywhere on the desktop “Properties” “Settings”, and applies the resolution to1024X768. Click the “Advanced” button, change “Refresh rate” to 60Hz.These 6 preset modes cover most of the common video modes supported bypopular graphic adaptors. However, each adaptors implementation of thesevideo modes may vary slightly in timings. You may find it necessary to makeminor adjustments to the display settings (i.e., horizontal position) usingthe On Screen Display. For further information and instructions on usingthe On Screen Display, please refer to “Controls and Functions.”
INSTRUCTION MANUAL 8A. POWER ON/OFF( )Turns the power ON or OFF. There will be a few seconds delay beforethe display appears.The power LED(next to the power switch) lights when the poweris turned ON.The power is turned off by pressing the power switch again andthe power LED goes out.B. MENUActivates and exits the On Screen Display. Auto AdjustScreen : Brightness, Contrast, H. Position, V. Position, Phase Adjust, Clock AdjustColor : Color Temp, Red, Green, BlueUtility : Recall, Full AutoLanguage: English, Francais, Deutsch, Espanol, OSD : OSD Timeout, OSD H. Position, OSD V. Position, OSD TransparencyC. AUTO( )Auto geometry adjustment.CONTROLS AND FUNCTIONSB. MENU BUTTONE. ADJUST BUTTONS(LEFT & RIGHT)D. SELECT BUTTONPOWER INDICATOR(LED)A. POWER SWITCHC. AUTO
9 INSTRUCTION MANUALCONTROLS AND FUNCTIONSD. SELECT( )The select button allows user to activate the desired adjustmentwith changing the adjustment bar to green.E. ADJUST ( , )The Adjust button allows user to choose the icons (controls) in the menu.Pressing the adjust button or will step through all availableadjustment icons (controls).In addition this adjust button can be used to adjust the icons (controls)that is selected and changing the adjustment bar to green via the select button whenthe adjust button is pressed, the window containing an adjustment bar will increaseor decrease.After completing all the desired adjustments, the On Screen Displaywill disappear with pressing the menu button.1. SELF-TEST DISPLAYWhen there is no connection, the On Screen Display will show “Check Input Signal”for 5 seconds.Check Input Signal2. OSD MENU DESCRIPTIONAuto AdjustAuto geometry adjustment.This function can be also activated by pushing the “AUTO” buttonon the monitor without the OSD window. To get the best quality of picture, while any stop motion image to the screen,click the “start” button of Windows “system shutdown” and then push the “AUTO” button on the monitor to Auto-adjustment. Cancel the “shutdown”.If there is still noise, use Phase Adjust / Clock Adjust function.
ScreenAdjusts the Brightness, Contrast, H. Position, V. Position, Phase and Frequencyof the Screen.BrightnessIncreases( ) or decreases( ) the intensity(illumination) of the image.ContrastIncreases( ) or decreases( ) the strength(lightness or dimness) of the image.H. PositionMoves images to left( ) or right( ).V. PositionMoves images to up( ) or down( ).Phase AdjustAs removing horizontal noise, adjusts the focus of the screen’s image.Clock AdjustThe clock adjust function can be used, if the screen image is shaking orhorizontal size isn’t fitted with bezel size. This noise can be caused by someabnormal modes.INSTRUCTION MANUAL 10CONTROLS AND FUNCTIONS
11 INSTRUCTION MANUALCONTROLS AND FUNCTIONSColorAdjusts the Color Temperature, Red, Green, Blue of the Screen.Color TempAdjusts color temperature to 9300K, 6500K, custom color mode. (9300K is Factory default data)RedIncreases or Decrease the strength of the Red.GreenIncreases or Decrease the strength of the Green.BlueIncreases or Decrease the strength of the Blue.UtilityExtra Functions. (Recall, Full Auto)RecallResets the control functions back to the original factory preset values.Full AutoAuto-adjusts of geometry and color balance.
INSTRUCTION MANUAL 12CONTROLS AND FUNCTIONSLanguageSelects a language among English, Francais, Deutsch, Espanol, .OSDAdjusts the OSD Timeout, OSD H. Position, OSD V. Position and Transparency of the OSDOSD TimeoutAdjusts the OSD display timing.Increase or Decrease the display time of the OSD.OSD H. PositionMoves the OSD position to left/right.OSD V. PositionMoves the OSD position to up/down.OSD Transparency Increase or Decrease the display Transparency of the OSD.ExitExit user menu.
F. DC JACKAC/DC adaptor connection.G. D-SUB CONNECTOR Connect to the video signal cable.AC/DC ADAPTORACCESSORY1. POWER CORD2. USE’R MANUAL3. AC/DC ADAPTOR4. VIDEO SIGNAL CABLEREAR VIEWF. DC JACK2G. D-SUB CONNECTOR112GROUNDDC+12V out13 INSTRUCTION MANUAL
Pin 123456789101112131415RED VIDEOGREEN VIDEO SIGNAL CABLE DETECTBLUE VIDEO GROUNDGROUND SDA(for DDC)GROUND H-SYNC.(or H+V SYNC.)RED GROUND V-SYNC.GREEN GROUND SCL(for DDC)BLUE GROUNDD-SUB CONNECTORPIN ASSIGNMENTSPIN ASSIGNMENTSD-SUBINSTRUCTION MANUAL 14
MODEONSTANDBYSUSPENDACTIVE OFFNOT PRESET MODEOUT OF RANGEGREENAMBER GREENLED COLOR MONITOR OPERATIONNormal OperationScreen blanks after preset idle timeand some electronic circuits or allcircuitry in the monitor shut down.Normal operation but the on screendisplay will show error massage.This monitor features a power management system to “power down” upon receipt of theVESA DPMS(The display power management signaling) from a VESA DPMS videocard.The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal.This monitor enters an appropriate mode through identifying each of the three modesof the signaling system.POWER CONSUMPTIONLED INDICATORThe power management feature of the monitor is comprised of fourstages : On(Green), Standby, Suspend, Active off(Amber)and Not preset mode(Green).< 35W< 5W< 5W< 5WMODEONSTANDBYSUSPENDACTIVE OFFPOWER CONSUMPTIONPOWER MANAGEMENT15 INSTRUCTION MANUAL
SPECIFICATIONSLCD Type15.0 Diagonal AM-TFT(Active-Matrix)DOT PITCH: 0.297mmBRIGHTNESS: 250cd/ (Typical)CONTRAST RATIO: 300:1(Typical)RESPONSE TIME: 25 msec(Typical)RESOLUTION(H x V)1024X768 @60HzFREQUENCYHORIZONTAL: 31-60KHzVERTICAL: 56-75HzVIDEO DOT RATE80MHzINPUT SIGNALVIDEO(Analog 0.7Vp-p / 75 )SYNC(Separate TTL Level)ACTIVE DISPLAY AREA (W x H)304mm X 228mmDIMENSIONS (W x D x H)367mm X 181mm X 358mmWEIGHTNet Weight : 3KgGross Weight : 5KgELECTRICAL RATINGSINPUT: AC100 - 240V, 50/60Hz (auto switching)OUTPUT: DC12V, 2.5ANNOOTTEE ::Technical specifications are subject to change without notice.INSTRUCTION MANUAL 16
No image on display screen“Check Input Signal”message on screenDisplay image is notcentered, too small or too largeVertical or Horizontal noiseis present in the picture1. Check that power cord of the Monitor havebeen connected securely into wall outletor grounded extension cable or strip.2. Power switch should be in the ON positionand LED is lit.3. Check that the Brightness and/or the Contrastadjustments of the Display have not beenturned down to minimum levels.1. The signal cable should be completelyconnected to the video card/computer.2. The video card should be completely seated inits slot and the computer is switched ON.Select “Auto” in the OSD.Adjust H-Size and Clock-Phase in the OSD.TROUBLESHOOTING TIPTROUBLESHOOTING GUIDETROUBLE17 INSTRUCTION MANUAL
Achten Sie darauf, da das Gerät nur in eine AC100-240V(DC12V) Schuko-Steckdose eingesteckt wird.Die Steckdose sollte jederzeit frei zugänglich sein, um bei einem evtl.auftretenden Notfall das Gerät schnell von der Stromversorgung zu trennen.Achten Sie desweiteren darauf, da die Netzanschlu leitung nichtmechanisch beansprucht noch sonstwie beschädigt wird.Öffnen Sie niemals das Gerät! Im Inneren befinden sich Teile mitgefährlicher Spannung.Bevor Sie das Gerät reinigen, ziehen Sie bitte den Netzstecker aus derSteckdose. Säubern Sie das Gerät dann mit einem feuchten (keinesfallstropfnassen) Lappen.Das Gerät ist funkentstört nach EN55022, EN55024 & EN61000-3-2 / -3-3. Stellen Sie das Gerät an einem ergonomisch günstigen Ort auf und sorgenSie dafür, da der Betrieb des Monitors mit nach ISO9241-3.7.8geprüfter Peripherie sichergestellt ist.Maschinenlärminformationsverordnung 3. GSGV, 18.01.91 : Derarbeitsplatzbezogene Schalldruckpegel beträgt 70dB(A) oder wenigergemä ISO 7779.Falls SIe dennoch Fragen haben, auf die die Bedienungsanleitung keineAntwork geben kann, so kontaktieren Sie bitte den nächsten Fachhändler.FOR GERMAN WICHTIGE HINWEISEINSTRUCTION MANUAL 18

Navigation menu