Orion Electric Co LN710S 17 inch LCD Monitor User Manual Manual

Orion Electric Co Ltd 17 inch LCD Monitor Manual

users manual

CONTENTSSAFETY INSTRUCTION 2CAUTIONS 4FCC RF INTERFERENCE STATEMENT 5CONNECTING WITH EXTERNAL EQUIPMENT 6RESOLUTIONS 7CONTROLS AND FUNCTIONS 8REAR VIEW 13D-SUB CONNECTOR PIN ASSIGNMENT 14POWER MANAGEMENT 15SPECIFICATIONS 16TROUBLESHOOTING GUIDE 171…………………………………………….…………………………...…INSTRUCTION MANUALSAFETY INSTRUCTION 1. Read all of instructions. 2. Save these instructions for later use. 3. Follow all warnings and instructions marked on the product. 4. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use this product near water. 6. Do not place this product on an unstable cart, stand or table. The product may fall, causing serious damage to the product.7. Slots and openings in the cabinet and the back are provided for ventilation : to ensure reliable operation of the product, these openings must not be blocked by placing the product on a bed, sofa, rug or other similar surface This product should never be placed near or over a heat resister. This product should not be placed in a built-in installation unless proper ventillation Is provided.8. This product should be operated from the type of power source indicated on the Marking label. If you are not sure of the type of power available, consult your dealer or local power company.9. This product is equipped with a 3 wire grounding type plug having a third(grounding) pin. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.10. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.11. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord ampere rating. Also, make sure that the total of all products plugged into the wall outlet does not exceed 10 amperes.12. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill any kind of liquid on the product.13. Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to service personnel. INSTRUCTION MANUAL………………………………………………………………………………...2This Monitor wasManufactured ISO9001Certified Factory
SAFETY INSTRUCTION 14. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions. A. When the power cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since importer adjustmentof other controls may result in damage and will often require extensive work by a qualified technician to restore normal operation. E. If the product has been dropped or the cabinet has been damaged. F. If the product exhibits a distinct change in performance, indicating a need for service. 44444444CCAAUUTTIIOONN The power supply cord is used as the main disconnect device, ensure that the Socket-outlet is located/installed near the equipment and easily accessible.3…………………………………………………………………...………...…INSTRUCTION MANUALCAUTIONS 44NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel. 44DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in the office or home. Do not subject the unit to Vibrations, dust of corrosive gases. 44KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from Rising. Do not cover the unit or place anything on the top of unit. 44AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance. 44TO ELIMINATE EYE FATIGUE Do not use the unit against a bright back ground and where sunlight or other light Sources will shine directly on the monitor. 44BE CAREFUL OF HEAVY OBJECT Neither the monitor itself nor any other heavy object should rest on the power cord. Damage to a power cord can cause fire or electrical shock. INSTRUCTION MANUAL………………………………………………………..…………………...4CAUTION TO SERVICE PERSONNELPOWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE INTHIS PRODUCT. UNPLUG THIS PRODUCT FROM THE WALL OUTLETBEFORE REMOVING THE BACK COVER AND SERVICING
FCC RFINTERFERENCE STATEMENT 44444444NNOOTTEE :: This equipment has tested and found to comply with the limits for a Class B digital device, pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, If not iastalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by on eor more of the following measures. - Reorient or relocate the receiving antenna. - Increase the seperation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio, TV technician for help. - Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by user not expressly approved by the guarantee or manufacturer could void the users authority to operate such equipment. 4444 DDOOCC CCOOMMPPLLIIAANNCCEE NNOOTTIICCEE The digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of Communications.5…………………………………………………………………...………...…INSTRUCTION MANUALCONNECTING WITH EXTERNALEQUIPMENT 44444444CCAAUUTTIIOONN Be sure to turn off the power of your computer before connecting the monitor.1. CONNECT THE VIDEO SIGNAL CABLEA. Connect one end of the signal cable to the back panel of the monitor and connect the other end to the graphic card on back of the computer. B. Secure the connection with the screws on the plug. 2. CONNECT THE POWER CORD A. Connect the plug of the AC/DC adaptor to the monitor. B. Connect the female end of the power cord to the power input receptacle on the AC/DC adaptor. Then, plug the male end of the power cord to an AC outlet or computer. 3. TURN THIS MONITOR ON AND START YOUR SYSTEM INSTRUCTION MANUAL………………………………………………………..…………………...6
RESOLUTION FREQUENCYPRESET MODES H(Pixels) V(Lines) H(KHz) V(Hz)640 350 31.5 70720 400 31.5 70640 480 31.5 60VGA640 480 43.2 85MAC 640 480 35.0 67800 600 37.8 60800 600 53.6 851024 768 48.3 601024 768 68.6 85VESA1280 1024 63.9 60 7…………………………………………………………………...………...…INSTRUCTION MANUALRESOLUTION This monitor is a digitally-controlled multi-frequency monitor.It operates at horizontal frequencies of 31 to 70KHz and vertical frequenciesof 60 to 85Hz.Because of its micro processor-based designs it offers auto-synchronizationand auto-sizing capabilities. This monitor offers 10 programmed settingsas listed in the table below.And designs its best quality at 1280×1024, 64KHz@60Hz.These 10 preset modes cover most of the common video modes supported bypopular graphic adaptors. However, each adaptors implementation of thesevideo modes may vary slightly in timings. You may find it necessary to makeminor adjustments to the display settings (i.e., horizontal position) usingthe On Screen Display. For further information and instructions on usingthe On Screen Display, please refer to “Controls and Functions”.CONTROLS AND FUNCTIONSA. POWER ON/OFF( ) )Turns the power ON or OFF. There will be a few seconds delay beforethe display appears.The power LED(next to the power switch) lights when the poweris turned ON.The power is turned off by pressing the power switch again andthe power LED goes out.B. MENU (MENU)Activate sand exits the On Screen Display. This button can also beused to move previous menu or status.MAIN MENU : BRIGHTNESS / CONTRAST, COLOR TEMPERATURE, FREQUENCY&PHASE, POSITION, LANGUAGE, UTILITIES, EXITINSTRUCTION MANUAL………………………………………………………..…………………...8
CONTROLS AND FUNCTIONSMAIN MENU activates when you press the Menu button. C. SELECT (SELECT) The select button allows user to activate the desired adjustment with blinking icon. D. ADJUST (DOWN, UP) The adjust button allows user to choose the icons(controls) in the menu. Pressing the adjust button Down or Up will step through all available adjustment icons(controls). In addition this adjust button can be used to adjust the icons(controls) that is selected and activated via the select button when the adjust button is pressed, the window containing an adjustment bar will increase or decrease. After completing all the desired adjustments, the On Screen Display will disappear with pressing the menu button. 1. SELF-TEST DISPLAY When there is no connection, the On Screen Display will show for 3 seconds.9…………………………………………………………………...………...…INSTRUCTION MANUALCONTROLS AND FUNCTIONS 2. MAIN MENU DESCRIPTION : BRIGHTNESS / CONTRAST BRIGHTNESS : Increase(+) or decrease(-) the intensity(illumination) of the image. CONTRAST : Increase(+) or decrease(-) the strength(lightness or dimness) of the image. : COLOR TEMPERATURE Adjusts color temperature to 9300K, 8000K, 6500K, 5000K (Notes : 9300K is factory default). : FREQUENCY, PHASE FREQUENCY : Adjusts the horizontal noise of screen image. PHASE : Adjusts the vertical noise of screen image.INSTRUCTION MANUAL………………………………………………………..…………………...10Check Cable or No Signal
CONTROLS AND FUNCTIONS : POSITION VERTICAL : Moves images vertically on screen up() or down(). HORIZONTAL : Moves images horizontally on screen right(+) left(-). : LANGUAGE Selects a language among ENGLISH, KOREAN, GERMAN, FRENCH, SPANISH, ITALIAN. : UTILITIES11…………………………………………………………………...………...…INSTRUCTION MANUALCONTROLS AND FUNCTIONS USER Settings OSD Horz Position : Moves the OSD position to right(+) or left(-). OSD vert Position : Moves the OSD position to up() or down(). OSD Background : Selects the OSD background. User Timeout : Selects the OSD display timing. Auto Adjust Automatically adjusts the contrast, the image position, and the clock-phase settings. Reset to factory defaults Press “Select”key to reset all setting to the factory default values. Zooming Increase(+) or decrease(-) the screen size.INSTRUCTION MANUAL………………………………………………………..…………………...12
REAR VIEWE. DC JACK AC/DC adaptor connection.F. D-SUB CONNECTORC JACK Connect to the video signal cable. E. DC JACK F. D-SUB CONNECTOR AC/DC ADAPTOR 1 : GROUND 2 : DC+12V out  ACCESSORY 1. POWER CORD 2. INSTRUCTION MANUAL 3. AC/DC ADAPTOR 4. VIDEO SIGNAL CABLE13…………………………………………………………………...………...…INSTRUCTION MANUALD-SUB CONNECTORPIN ASSIGNMENTS PIN ASSIGNMENTS D-SUBINSTRUCTION MANUAL………………………………………………………..…………………...14Pin 1 RED VIDEO 92GREEN VIDEO 10 GROUND3BLUE VIDEO 114 12 SDA(for DDC)5GROUND 13 H-SYNC.(or H+V SYNC.)6RED GROUND 14 V-SYNC.7GREEN GROUND 15 SCL(for DDC8BLUE GROUND
POWER MANAGEMENTThis monitor features a power management system to “power down” upon receipt of theVESA DPMS(The display power management signaling) from a VESA DPMS videocard.The VESA DPMS-compliant video card performs this signaling system through notsending horizontal, vertical, or sync signal.This monitor enters an appropriate mode through identifying each of the three modesof the signaling system.POWER CONSUMPTION LED INDICATORThe power management feature of the monitor is comprised of fourstages : On(Green), Standby, Suspend, Active odd(Amber blinking)and Not preset mode(Amber).15…………………………………………………………………...………...…INSTRUCTION MANUALSPECIFICATIONS LCD Type 17.0” Diagonal AM-TFT(Active –Matrix) DOT PITCH : 0.264mm BRIGHTNESS : 200cd/m2(Typical) CONTRAST RATIO : 350 : 1(Typical) RESPONSE TIME : 20msec(Typical) Resolution(H ×V) 1280 ×1024 @ 60Hz Frequency HORIZONTAL : 31–70KHz VERTICAL : 60-85Hz  VIDEO DOT RATE 108MHZ  INPUT SIGNAL VIDEO(Analog 0.7Vp-p / 75) SYNC(Separate and Composite TTL Level) ACTIVE DISPLAY AREA (W ×H) 338mm ×270mm DIMENSION (W ×D ×H) 494mm ×240mm ×537mm(Carton Box) WEIGHT Net Weight : 7.3Kg Gross Weight : 8.5Kg  POWER SUPPLY INPUT : AC100-240V, 50/60Hz(auto switching) OUTPUT : DC12V, 3.5A  NOTE : Technical specifications are subject to change without notice.INSTRUCTION MANUAL………………………………………………………..…………………...16MODE POWER CONSUMPTIONON <45WSTANDBY <5WSUSPEND <5WACTIVE OFF <5WMODE LED COLOR MONITOR OPERATIONON GREEN Normal OperationSTANDBYSUSPENDACTIVE OFFNOT PRESETMODEOUT OF RANGE GREEN Normal operation but the on screendisplay will show error massage.MODE POWER CONSUMPTIONON <45WSTANDBY <5WSUSPEND <5WACTIVE OFF <5W
TROUBLESHOOTING GUIDE17…………………………………………………………………...………...…INSTRUCTION MANUALTROUBLE TROUBLESHOOTING TIPNo image on display screen1. Check that power cord of the Monitor havebeen connected securely into wall outletor grounded extension cable or strip.2. Power switch should be in the On positionand LED is lit.3. Check that the Brightness and/or the Contrastadjustments of the Display have not beenturned down to minimum levels.“No signal, Check signalCable” message on screen1. The signal cable should be completelyconnected to the video card/computer.2. The video card should be completely seated inits slot and the computer is switched ON.Display image is notcentered, too small ortoo large Select Auto-adjust in the OSD.Vertical or Horizontal noise ispreset in the picture Adjust Frequency and Phase in the OSD.

Navigation menu