Orolia PLB-3-GPS Fastfind User Manual 32223 fstfnd manual 120x120
Orolia Ltd Fastfind 32223 fstfnd manual 120x120
Orolia >
User manual
32223 fstfnd manual 120x120 28/1/09 12:09 USER MANUAL FAST FIND MODELS 200 & 210 GET FOUND WITH FAST FIND Page 2 32223 fstfnd manual 120x120 28/1/09 12:09 Page 3 SAFETY NOTICES WARNING: A Personal Locator Beacon (PLB) is an emergency radio beacon; Use only in situations of grave and imminent danger to life. CAUTION: False alerts endanger lives and cause expensive disruption to Search and Rescue services, deliberate misuse of the PLB could result in penalty and fine. CAUTION: Spring action antenna deployment; tilt the PLB away from your face when deploying the antenna. CAUTION: Do not dismantle the PLB, contains no user-serviceable parts. CAUTION: Contains lithium batteries. Do not incinerate, puncture, deform, short-circuit or recharge. CAUTION: Dispose of a used PLB in accordance with local waste disposal regulations. Refer to End of Life Statement. Your PLBs unique identification information CAUTION: Avoid using chemical solvents to clean the PLB as some solvents can damage the case material. CAUTION: Radio licensing, the PLB is a radio transmitter. Some administrations may require that the user holds a valid radio license to cover its ownership and use. CAUTION: The PLB will not float; fit a lanyard restraint when near water to avoid loss. RADIO FREQUENCY EXPOSURE WARNING WARNING: The PLB emits low levels of radio frequency radiation; avoid handling the antenna once activated. REGISTRATION WARNING: The PLB must be promptly registered with the appropriate National Authority. Failure to register the PLB could delay a Search and Rescue (SAR) response and may be unlawful. Stick copy Programming label here 32223 fstfnd manual 120x120 28/1/09 12:09 Page 4 GET FOUND WITH FAST FIND INTRODUCTION Congratulations on purchasing the Fast Find Personal Location Beacon (PLB). When carrying a Fast Find you enjoy the reassurance of a last resort safeguard against any life threatening incidents that may occur anywhere in the world. If you find yourself in a remote area without any other form of emergency communication, on land or at sea, your Fast Find can call for help. Fast Find will transmit a unique emergency identifier to the Cospas Sarsat satellite system which can determine your location anywhere on the earth’s surface. In most cases the emergency alert is received within 5 minutes of activation but depending on satellite coverage at the time this can sometimes extend to 45 minutes. When the emergency alert message is received at a Rescue Co-ordination Centre (RCC) it is cross referenced using the unique identifier (often called Hex ID) against your registration details. Detail of the alert is forwarded to the appropriate local Search And Rescue (SAR) teams. Keeping your registration details up to date is critical to ensuring a quick SAR response. Fast Find has a secondary ‘homing’ transmitter which allows SAR teams to direction find or ‘home’ on it once they arrive on scene. Fast Find has a storage life of 5 years and once activated will continue to transmit emergency alerts for a minimum of 24 hours. For further information visit Cospas Sarsat on line at www.cospas-sarsat.org and www.mcmurdo.co.uk. The ‘frequently asked questions’ section is a good place to start. 32223 fstfnd manual 120x120 28/1/09 12:09 Page 5 GPS VERSION USER REGISTRATION Fast Find 210 has a built-in Global Positioning System (GPS) receiver to potentially reduce the time for SAR teams to arrive on scene. If the sky view is obscured by tree canopy or a steep-sided canyon, the GPS may take longer, or possibly fail to obtain a position fix. In this case the distress alert may be transmitted without GPS location information. The PLB’s unique identifier must be registered with the national authority indicated in the white area on the rear of the PLB. Complete the user registration form and return it to the address indicated on the form. Some national authorities allow online registration, a good starting place is the online emergency beacon registration database called IBRD at www.406registration.com. IBRD will not accept all registrations and where appropriate you will be re-directed to your national authority. Some countries (including USA and UK) will send the registered user a DECAL label which you are obliged to fit to the rear of the PLB as ‘proof of registration’. RADIO LICENSE U.S. users are not required to hold a radio license for a PLB. Other national administrations may require the PLB user to be licensed, for further advice check with your dealer or contact your national communications licensing authority. Battery expiry date Country name & Hex ID Fit “proof-of-registration” DECAL label here 32223 fstfnd manual 120x120 28/1/09 12:09 Page 6 GET FOUND WITH FAST FIND OVERVIEW Red pull handle Pull to expose antenna Only pull in an emergency Pulling breaks the plastic anti-tamper seal that can not be reset by the user. White indicator Light Flashes every 3 seconds once PLB is active, Long flash every 50 seconds means satellite transmission OK For PLB 210 only Flashes twice a second when GPS is searching 3 rapid flashes means GPS location sent Antenna Unwraps and stands vertical once cover is off GPS antenna zone (PLB 210 only) Do not obstruct Needs a clear view of the sky for best operation ON button Press once to activate PLB. When the PLB is on, push the ON button again to make the indicator light flash an SOS signal pattern. TEST / OFF button Push and hold to start the self test feature, a flash of white light indicates that the self test is successful. Once PLB is active Hold TEST to turn PLB off Eyelet for lanyard 32223 fstfnd manual 120x120 28/1/09 12:09 ACTIVATING THE FASTFIND PLB Only ever activate in situations of grave or imminent danger. 1) Flip up the red pull handle, Pull the antenna cover off IMPORTANT The antenna cover is an anti-tamper seal, once broken it can not be refitted. 2) Hold the end of the antenna. Unwrap the antenna until it stands vertical CAUTION Spring action antenna deployment; tilt the PLB away from your face before deploying the antenna. 3) Press the ON button Transmission of the first emergency alert message takes place 50 seconds after initial activation, in the event of an accidental or false activation this delay allows time for the user to turn off the Fast Find before the first alert is transmitted. Page 7 32223 fstfnd manual 120x120 28/1/09 12:09 Page 8 GET FOUND WITH FAST FIND DEPLOYING THE PLB • Always position the PLB so that the antenna stands vertical • If it’s windy, rotate the PLB so that the white indicator light faces into the wind YES YES Do NOT allow the PLB to tip over NO Do NOT hold the antenna NO Do NOT allow the antenna to sit in a puddle of water Do NOT cover the GPS antenna zone Use around water The Fast Find will NOT float but is waterproof to 10 meters submersion for short periods. To avoid loss if dropped into water fit a retaining lanyard through the eye hole in the base of the PLB and fasten it securely to your clothing or personal floatation device. The PLB is not a substitute for an EPIRB that may be required under maritime regulation. Note: In some countries the Fast Find PLB may be sold with an auxiliary flotation device but is not designed to float in an upright position or transmit a distress alert when floating in water. 32223 fstfnd manual 120x120 28/1/09 12:09 Page 9 INDICATOR LIGHT FLASH SOS FEATURE The indicator light will start flashing immediately the Fast Find is activated When the PLB is active, pressing the ON button will cause the indicator light to flash a Morse code SOS pattern. This can be used to attract attention after nightfall. The SOS pattern is repeated four times on each press. FAST FIND 200 Light indication PLB ACTIVE 1 flash every 3 seconds SATELLITE TRANSMISSION OK Large flash once every 50 seconds FAST FIND 210 WITH GPS Light indication GPS SEARCHING 2 flashes every 1 second SATELLITE TRANSMISSION SENT WITH GPS LOCATION OK Sequence repeats every 50 seconds PLB ACTIVE 1 flash every 3 seconds To conserve battery life a maximum of 30 presses are allowed, after which this feature is disabled. 32223 fstfnd manual 120x120 28/1/09 12:09 Page 10 GET FOUND WITH FAST FIND DE-ACTIVATION AFTER USE To turn off the Fast Find, press and hold the TEST button for several seconds until the indicator light stops flashing. We recommend the antenna is re-wound under the plastic peg. If possible, the yellow antenna cover should be pushed back in place and temporarily taped over, to avoid accidentally pressing of the ON button. Important As soon as possible the PLB should be returned to a service agent, who will fit a new antenna cover and check the battery condition. If the PLB was active for more than a few hours we recommend fitting a fresh battery to ensure the full 24 hour operational life is still available. SELF TEST Self-test verifies operation of the PLB by checking all key features including the battery and alert transmitters. TEST button Push and hold the SELF TEST button for a minimum of 2 seconds, the indicator light will flash once to indicate the start of the self test sequence. After a few seconds, a good self-test will result in the indicator light flashing a number of times in quick succession depending on battery usage; fresh battery self test pass minimum usage self test pass medium usage self test pass NO FLASH self test fail PLB requires service The PLB will switch off automatically when the self-test has completed Important Each self-test draws small amounts of energy from the battery pack. Unnecessary testing of the PLB will reduce the run time of the PLB in an emergency. On average, the PLB should only be self tested 12 times per year, or a total of 60 times during the 5 year battery lifetime. 32223 fstfnd manual 120x120 28/1/09 GPS POSITION ACQUISITION TEST When testing the GPS, take the PLB outside into an open space with a clear view of the surrounding sky. Self testing of the in-built GPS is restricted to a maximum of 10 tests throughout the 5 year storage life of the battery. Once all the tests have been used up, attempting further tests will cause the indicator light to flash 4 times in quick succession and the PLB to power off. The GPS self-test feature can only be accessed after first completing a standard PLB self-test routine; Push and hold the TEST button for a minimum of 2 seconds, the indicator light will flash once to indicate the start of the self test sequence. Release the TEST button. After a few seconds the standard self-test routine will complete and should result in the indicator light flashing a number of times in quick succession depending on the past battery usage. Immediately after the indicator light stops flashing, hold down the TEST button for around 30 seconds. The GPS test routine starts when the indicator light begins to flash, now release the TEST button. The light will continue to flash slowly for up to 5 minutes; you should continue to watch the PLB throughout this period. 12:09 Page 11 A successful GPS test is signalled by the indicator light flashing a number of longer flashes in quick succession. GPS self test pass 10 – 4 GPS tests remaining GPS self test pass 3 – 1 GPS tests remaining GPS self test pass No GPS tests remaining Important To preserve battery life, GPS testing is restricted to a maximum of 10 tests throughout the 5 year battery life. Once used up, further GPS tests are prohibited. CHOOSING THE BEST LOCATION The Fast Find works best under an unobstructed view of the sky. This ensures the emergency alert message reaches the satellite system and gives the GPS receiver (Fast Find 210) the best signals to work with. If it’s not possible to pick a location with an unobstructed view of the sky, then try to maximize the amount of sky available. Tree canopy degrades performance. Find a clearing with as much sky view as possible. Ravines, canyons, caves and overhangs should be avoided if at all possible. 32223 fstfnd manual 120x120 28/1/09 12:09 Page 12 GET FOUND WITH FAST FIND Stay put - Rescue teams expect you to remain stationary. Trying to walk for help is generally not advised and will probably slow down the rescue effort. On foot If you must walk for help, ensure the Fast Find antenna remains vertical. Aircraft A PLB is often used as an additional carry-off safety device. The PLB should NOT be activated aboard an aircraft. The signal will be blocked by metalwork and the PLB may be damaged by any impact. Activate the PLB after landing, away from the aircraft, as it may cause shadowing. Vehicles The PLB will not work well inside a vehicle due to metalwork shadowing. Exit the vehicle, activate the PLB, and place it on the roof, the hood, or just on the ground away from the vehicle. Land Find the best sky view, then place the PLB on flat ground. Keep the antenna pointing towards the sky and ensure wind doesn’t knock the PLB over. Do NOT allow the antenna to sit in a puddle of water. Aboard ship Place the PLB flat on the deck, choosing a position with the best sky view. Liferaft Try to keep the PLB flat and try to elevate the PLB to avoid bodies blocking the signal. Consider holding the PLB outside the canopy. But first attach a lanyard between the PLB and your clothing to avoid loss of the PLB. Lifejacket Attach a lanyard cord between the PLB and clothing to avoid loss of the PLB. Hold the PLB flat on top of the life vest and try to keep it above any wave wash. Keep the antenna vertical. Avoid holding the antenna, or blocking the GPS zone with your hand. False alerts If the PLB has been accidentally activated, or if rescue has been effected before arrival of the rescue services: • Switch off the PLB and notify the appropriate rescue services or authorities at the earliest possible time. • Contact the rescue services, coastguard, or police by radio or telephone to advise them of the false alert. In the U.S. call 1-800-851-3051 In the UK call MRCC Falmouth +44 1326 317575 11 32223 fstfnd manual 120x120 28/1/09 TRANSPORTATION Passenger Aircraft; These products contain small lithium metal batteries. They can normally be carried on board passenger aircraft as a personal item in carry-on baggage. McMurdo always recommends declaring the PLB to airline staff at check in, in the same way you would for a laptop PC or video camera. As air cargo; These products contain small lithium metal batteries. Due to the overall low level of lithium content they are not restricted as air cargo under IATA SP 188 - PI 970, always check with the carrier concerned for any additional restrictions that could apply. END OF LIFE STATEMENT At the end of the products useful life, it is vital that the battery is removed from the main body of the PLB to prevent false alerts. False alerts cause expensive disruption to Search and Rescue services and may endanger lives as a consequence. Safe disposal Contains traces of lithium, may contain lead and brominated flame retardants (BFRs), both in the housing material and circuit boards. 12:09 Page 13 DO NOT INCINERATE McMurdo strongly recommends that this PLB product is disposed of in a sensible and considerate manner. For example, do not simply discard the product in the domestic waste. Instead take it to a civil recycling facility, or contact McMurdo for advice. 32223 fstfnd manual 120x120 28/1/09 12:09 Page 14 GET FOUND WITH FAST FIND FAST FIND 200, 210 STANDARDS APPLIED COSPAS-SARSAT T.001/T.007 class2 RTCM SC110 STD 11010.2 ETSI EN 302-152-1 AS/NZS 4280.2 NSS-PLB06 ENVIRONMENTAL Exterior Finish Sealing Highly visible yellow Temporary immersion to 10m (30 ft) for 5 mins. (IP 58, IPX7) Operating Class 2, -20°C to +55°C temperature (-4°F to +131°F) Storage Temperature Class 2, -30°C to +70°C (-22°F to +158°F) Altitude MIL-STD-810E (10,000 feet) BATTERY Battery Type Battery storage Battery replacement Battery use OPERATION Activation Self test SOS flash light 6V Lithium Metal 5 years By service centre Logged by microcontroller. Three stage manual activation Tests transmitters, battery and light Morse code SOS pattern (30 operations allowed) TRANSPORTATION Air cargo UN 3091, not restricted, IATA SP 188 - PI 970 ELECTRICAL 406.037 MHz transmitter 121.5 MHz transmitter Homer sweep direction Transmit Antenna Programming interface PHYSICAL Fast Find 200, 210 Size (D x W x L) Weight GPS Receive Antenna GPS Self test PART NUMBER 91-001-200A 91-001-210A ± 1KHz, 5W ± 2dB ± 3KHz, 50mW ± 3dB PERP UP or DOWN Deployable flexible vertical blade Optical Infra-red link Category 2, will not float 34 x 47 x 106 mm (1.34” x 1.85” x 4.17”) 150g ( 5.3 oz) (Fast Find 210 only ) 50 channel Ceramic Patch Position acquisition test (10 operations allowed) Fast Find 200 PLB retail pack Fast Find 210 PLB (with GPS) retail pack FAST FIND 200, 210 models do not float and are not recommended for use on or in water unless provided with an auxiliary flotation device. A Fast Find PLB is not an ELT or an EPIRB and does not meet the regulatory requirements for an ELT or an EPIRB. 13 32223 fstfnd manual 120x120 28/1/09 12:09 Page 1 DISCLAIMER McMurdo is a brand name operated by Signature Industries Limited. The information and illustrations contained in this publication are to the best of our knowledge correct at the time of going to print. We reserve the right to change specifications, equipment, installation and maintenance instructions without notice as part of our policy of continuous product development and improvement. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise without permission in writing from McMurdo, Signature Industries Limited. No liability can be accepted for any inaccuracies or omissions in the publication, although every care has been taken to make it as complete and accurate as possible. DISCLAIMER McMurdo is a brand name operated by Signature Industries Limited. The information and illustrations contained in this publication are to the best of our knowledge correct at the time of going to print. We reserve the right to change specifications, equipment, installation and maintenance instructions without notice as part of our policy of continuous product development and improvement. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise without permission in writing from McMurdo, Signature Industries Limited. No liability can be accepted for any inaccuracies or omissions in the publication, although every care has been taken to make it as complete and accurate as possible. DISCLAIMER McMurdo is a brand name operated by Signature Industries Limited. The information and illustrations contained in this publication are to the best of our knowledge correct at the time of going to print. We reserve the right to change specifications, equipment, installation and maintenance instructions without notice as part of our policy of continuous product development and improvement. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise without permission in writing from McMurdo, Signature Industries Limited. No liability can be accepted for any inaccuracies or omissions in the publication, although every care has been taken to make it as complete and accurate as possible. 91-210 Iss 1
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 for Macintosh Create Date : 2009:01:28 12:10:34Z Modify Date : 2009:01:28 12:12:20Z Creator Tool : QuarkXPress: pictwpstops filter 1.0 Metadata Date : 2009:01:28 12:12:20Z Format : application/pdf Title : 32223 fstfnd manual 120x120 Creator : silverfox Document ID : uuid:e9b5bf7e-ed34-11dd-9ab9-0011246eef20 Instance ID : uuid:e9b5c440-ed34-11dd-9ab9-0011246eef20 Page Count : 14 Author : silverfoxEXIF Metadata provided by EXIF.tools