Ortek Electronics TD-650 Car Radio User Manual
Shanghai Ortek Electronics Co.,LTD Car Radio
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3895625 |
| Application ID | SpaObINevmHFayUNCyFKFg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 83.11kB (1038903 bits) |
| Date Submitted | 2018-06-20 00:00:00 |
| Date Available | 2018-06-20 00:00:00 |
| Creation Date | 2018-06-12 16:10:28 |
| Document Lastmod | 2018-06-12 16:10:28 |
| Document Title | User Manual |
| Document Creator | WPS Office |
| Document Author: | User |
Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 TD - 650 Car Radio User Manual Shanghai Ortek Electronics Co.,LTD. Address: Bridge 16 southern, Cao’an Road, Jiading District, Shanghai, China T：021-3911 7568 F：021-3911 7569#8031 PC：201812 E-Mai：mail@orteksh.com 1|Pa g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Thanks for choosing our product TD-650. To ensure safety and good user experience, please read this user manual thoroughly before starting to use the product. Important Note: 1. Please use the rated voltage stated on the product for power supply. 2. Please remain open circuit for BAT connection to avoid short circuit. 3. Please study the connection requirements carefully. 4. Please change a rated fuse if necessary. 5. Please do not knock down the product without professional guidance. 6. Please do not let metal or other things go into the inner part of the product to avoid unnecessary accident. 7. Please contact our aftersales service department by (86) 021-39117568 #8011. FCC Requirement （1）、changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. （2）、Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. （5） 、This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2|Pa g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Contents Control panel.…………………………………………………………………………………… ……………………….. LCD Display.………………………………………………………………………………… …………………………….. Power Up / Down…………………………………………………………………………………… ………………….. Time Setting.………………………………………………………………………………… …………………………… Mode Switching……………….……………………………………………………………… ………………………… Reset…………………………………………………………………………………… ……………………………………… Tune Operation………………………………………………………………………………… ………………………… Auto Seek Function Manual Seek Function Auto Preset Stations Manual Preset Stations Multiple Region Frequency Selection USB Play……………………………………………………………………………………… ……………………………… USB Mode Operation Sound Setting…………………………………………………………………………………… ………………………… Sound Effect Setting…………………………………………………………..……………………… ………………… Loud Function………………………………………………………………………………… ………………………….. Bluetooth Operation………………………………………………………………………………… ………………… 3|Pa g e P.4 P.5 P.6 P.6~7 P.7 P.7 P.8~11 P12~13 P.14 P.14 P.15 P.15~17 Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Bluetooth Connection Bluetooth Music Player Bluetooth Phone Function AUX IN Mode…..……….……………………………………………………………………… ………………………… Definitions………………………………………………………………………..……… …………………………………. Connector and Pin Definitions (Reference)………………………………………………………………….. Assembling Demonstration (Reference)………………………..……………………………………………… Maintenance…………………………………………………………………………… …………………………………… FAQ…………………………………….……………………………………………… ………………………………………… 4|Pa g e P17 P.18 P.19 P.20 P.20 P.20 Shanghai Ortek Electronics Co., Ltd. Control Panel 10 11 12 13 14 15 16 17 18 19 Microphone Loud / End of phone call / Refuse to pick up Mode Reset Volume control / Menu / Call pick up Preset radio stations / songs FM / AM selection Power on Clock display / Clock setting Preset station 1 / Play / Stop Preset station 2 / Pre-play song (fast scan) Preset station 3 / Repeat Preset station 4 / Random Preset station 5 / Next 10 songs Preset station 6 / Previous 10 songs Tune down / Next song Tune Up / Previous song USB / AUX connector LCD display 5|Pa g e P0B650X04A6 Shanghai Ortek Electronics Co., Ltd. LCD Display 10 11 12 13 14 15 16 17 Track indication Pre-play indication (fast scan) Repeat indication Folder indication Random indication File name indication POP effect indication Song name indication ROCK effect indication Album name indication CLASS effect indication Artist name indication FLAT effect indication FM stereo sound indication Loud indication Preset station indication Main display area 6|Pa g e P0B650X04A6 Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Power Up / Down 1. Press “PWR” to turn on. 2. Press “PWR” again to turn off. Time Setting Setting Method 1: Step1 Enter Time setting mode When the machine is turn on, it will display Time with 24-hr format. Press and hold “CLK” (>2 sec) until the display is flashing. Now you can start to set the Time. Step2 Set Hour Digit Following Step 1, by rotating “Switch 5”, you can add or minus the hour digit when the hour digit is flashing. Step3 Set Minute Digit Following Step 2, press “CLK” and minute digit starts to flash, by rotating “Switch 5” to add or minus the minute digit. Step4 End of setting The setting is completed if not operation within 5 secs. 7|Pa g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Setting Method 2: When the machine is under operation, press “CLK” to show Time information. Press “CLK” again or without operation within 5 secs then display goes back to normal mode. Press and hold “CLK” will enter Time setting mode. You can set the Time by the same procedure as Method 1。 Turn off the machine by pressing “PWR”, LCD backlight is off while Time still displays. Mode Switching 1. Press “PWR” to turn on the machine. 2. Press “MOD” to switch across different sound source correspondingly. If USB device is inserted, the machine will directly get into next mode. This machine has RADIO mode, Bluetooth PLAY mode, USB MP3 mode and AUX IN MP3 mode. Reset If the machine is malfunction, please use a pointy object to press the reset button to reset the machine to see if the machine can restore. Note: The machine uses FLASH for saving, preset stations will not be initialized. 8|Pa g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Tune Operation Frequencies of FM1, FM2, and FM3 are the same (E.g. for China range of FM frequency is 87.5 – 108.0MHz). Frequencies of AM1 and AM2 are the same (E.g. for China range of AM frequency is 522 - 1620 KHz). The machine can store the last frequency after turning off. If the FM signal is good then FM stereo sound indicator is “ ”lit up. Auto Seek Function 1. Press “BND” to switch from FM1, FM2, FM3, AM1 or AM2. 2. Press “ ” or “ ” to seek radio stations by tuning up or down respectively. The seeking will be stopped when station is sought. 3. Press “ ” or “ ” during auto seek, seeking will be stopped by interruption. 9|Pa g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Manual Seek Function 1. Press “BND” to switch from FM1, FM2, FM3, AM1 or AM2. 2. Press and hold “ ” or “ ” for 2 seconds to enter single step tuning. Each press then can increase or decrease the frequency by a designated step width (E.g. China step width: FM: 0.1MHz and AM: 9 KHz). 3. Press “ ” or “ ” each time to increase or decrease by a step width. 4. Go back to Auto Seek Function without operation in 5 secs. Auto Preset Stations 1. Press “BND” to switch from FM1, FM2, FM3, AM1 or AM2. 2. Press and hold “AS/PS” for 2 seconds to enable auto preset process. Preset stations will be stored starting from lower frequency to higher one. During the scanning process, each effective station will be played for 2 seconds and continue to scan. Press “AS/PS” again to interrupt and stop the auto preset process. 10 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Every Preset station set can store 6 stations. Preset stations are based on stronger signal, higher priority to be stored. After Auto preset station setting, “Preset button 1” will show the corresponding radio station. (Below is reference) If you reset again the preset stations, the previous preset stations maybe overwrite. (Below is for reference) Manual Preset Stations 1. Press “BND” to switch from FM1, FM2, FM3, AM1 or AM2. 2. Press “ ” or “ ” to tune until the frequency needed to be stored. 3. Press and hold any “1” ……“6” for 2 seconds to overwrite current frequency to preset station memory correspondingly. 4. Repeat the above procedures, FM1, FM2, FM3, AM1 and AM2 can stored at most 6 preset stations. If there is already a preset station previously, the new preset station will overwrite the previous one. (Below is for reference) 11 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Multiple Region Frequency Selection Operating Procedure During standby mode, press accordingly “LOU”, “MOD”, “AS/PS”, “BND” and any “1~5” which represent the corresponding area to complete selection. 12 | P a g e Area 1. China/ Europe 2. Middle East 3. America 4. Japan 5. Russia FM/AM FM AM FM AM FM AM FM AM FM AM Frequency Range 87.5 - 108.0MHz 522 - 1620KHz 87.5 - 108.0 MHz 531 - 1602KHz 87.5 - 107.9 MHz 530 - 1710KHz 76 - 90 MHz 522-1692KHz 65 - 74 MHz 522-1602KHz Step Width 0.1MHz 9KHz 0.1MHz 9KHz 0.2MHz 9KHz 0.1MHz 9KHz 0.1MHz 9KHz Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 USB Play 1. Press “PWR” to turn on. 2. Insert USB device into USB Port 3. If there are MP3 format files, then after several seconds, display total number of MP3 files. 4. After several seconds, display the current file sequence. 5. After several seconds, display the current sound track time. 13 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 USB Mode Operation Button Function Descriptions under USB Mode Press to pause or start to play, press and hold to stop. Press to play next song, press and hold for fast forward. Press to play previous song, press and hold for fast backward. Press to skip 10 songs and play the next 10th song. Press to skip 10 songs and play the previous 10th song. Press “INT” and LCD displays “INT”. Starting from next song, each song will be played for 8 seconds and jump to next song until pressing “INT” again. Press “RPT” and LCD displays “RPT”. The current song will be played repeatedly until pressing “RPT” again. Press “RDM” and LCD displays “RDM”. The play list will become random and until pressing “RDM” again. 14 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Sound Setting 1. Press “PWR” to turn on. 2. Press the rotary button, to switch Main-Volume, TREB, BASS or BAL left/right. 3. According to the LCD display, rotate to set corresponding as below. Item VOLVOL+ MAIN-V Volume decrease Volume increase TREB Treble decrease Treble increase BASS Bass decrease Bass increase BAL LxRx Balance left/right decrease Balance left/right increase 4. Complete setting without pressing any button for 5 seconds. The default function for the rotary button is MAIN-V. Sound Effect setting The machine has 4 sound effects for choosing. POP, ROCK, CLASSIC or FLAT. The default function is FLAT. 1. Press and hold the rotary button for 2 seconds to change setting. 2. Rotate the button to switch from POP, ROCK, CLASSIC or FLAT. 15 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 3. Complete setting without pressing any button for 5 seconds. Loud Function Press “LOU” to amplify the sound source especially when the volume is low. The LCD will display “LOUD ON”. Press again to turn off this function. Bluetooth Operation When you need to use the Bluetooth function, please enable the Bluetooth module of the phone device needed to be connected. Search and connect to our machine named: ORTEK_TD650. Connect successfully to start the below. Bluetooth Connection 1. Turn on phone Bluetooth. 2. Search for new device. When the machine is detected by the phone, click “connect”. When the connection is successful, LCD will display “ ” to represent 16 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 effective connection. 3. After connection, press “MOD” to switch the mode to BT PLAY Different phone may lead to different operation procedure. The above illustration is for your reference only. Bluetooth Music Player Functions of corresponding buttons under Bluetooth Mode: Button Functions Press to Pause / Play the music. If the music is paused, then LCD displays “PAUSE”. (Need phone support) Press to play the next song (Need phone support) Press to play the previous song (Need phone support) Press to play the next song (Need phone support) Press to play the previous song (Need phone support) 17 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Bluetooth phone function Functions of corresponding buttons under Bluetooth Mode: Button Functions Press to refuse the call when ringing. Press to end the call when calling. Press to pick up the call when ringing. Press to end the call when calling. Microphone for voice input. AUX IN Mode 1. Press “MOD” to switch to “AUX IN” mode. 2. Through 3.5mm AUX in cable, play external MP3 files in external device 18 | P a g e Shanghai Ortek Electronics Co., Ltd. including MP3 device / Phone device. Definitions LCD Display FM1+Digit FM2+Digit FM3+Digit AM1+Digit AM2+Digit USB MAX+Digit CUR+Digit PAUSE MUTE MAIN-V+Digit VOL+Digit TREB+Digit BASS+Digit BAL L+Digit/ R+Digit POP CLASSIC ROCK FLAT LOUD ON LOUD OFF BT PLAY PHONE AUX IN 19 | P a g e Definition Radio FM1 (Each set can store 6 preset stations) Radio FM2 Radio FM3 Radio AM1 Radio AM2 USB Mode USB device total MP3 files USB device current MP3 file number Pause Mute Volume Volume, same as MAIN-V Treble Bass Balance Sound effect Pop Sound effect Classic Sound effect Rock Sound effect Flat Loud On Loud Off Bluetooth Mode Phone call in Aux in Mode P0B650X04A6 Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Connector and Pin Definitions (Reference) Connector Pin No. Fuse（ATY-N 5A） Definition of each Pin for connector is shown as below: Pin No. Function Pin No. Function Battery +（BAT+） Battery -（GND） ACC —— Light Control（+12/24V） —— Antenna（9V） —— 10 —— —— 11 —— 12 —— 13 Left Speaker 14 Left Speaker + 15 Right Speaker 16 Right Speaker + The above connector and Pin definition is for reference only. You have to check with your engineer or our aftersales service department for more information. 20 | P a g e Shanghai Ortek Electronics Co., Ltd. P0B650X04A6 Maintenance When you need to clean the panel, please do not use with alcohol, phenyl-related or any corrosive solvent or water. Instead you can use tissue paper or some soft towel for cleaning. FAQ FAQ No sound after turning on the machine No Power Radio no signal Can do with auto seek Buttons malfunction USB can’t charge phone 21 | P a g e Possible reasons 1. Volume to low 2. Speaker not connected How to deal with 1. Volume Up 2. Check with the Speakers 1. ACC not turn on yet 2. Fuse broken 1. Antenna not connected 2. Bad signal in the region Bad signal in the region Possible Program bugs This machine may not have USB charging functions 1. Turn on ACC 2. Change the fuse 1. Check with the Antenna 2. Try again at open area Use manual seek instead Use reset button to reset Check with your vendor and don’t charge if not this function
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Page Count : 21 Create Date : 2018:06:12 16:10:28+00:00 Modify Date : 2018:06:12 16:10:28+00:00 Author : User Creator : WPS OfficeEXIF Metadata provided by EXIF.tools