Otter OBFTC-0010-A Bluetooth Eearphones User Manual Customer

Otter Products, LLC. Bluetooth Eearphones Customer

user manual

Otter Products, LLC. OBFTC-0010-A Page 1 of 2 Function of the headset operation Before operating each function of the headset, please read the following introduction: function button and time (seconds) status sketch remarks Power on In off mode ,pull apart the headset, it will power on . Red and blue indicator light will flash ,it will last for 1 second Could hear “Power on”/YEJ Pairing 1.Pull apart the headset ,it will enter into pairing mode automatically （never connected / paired with any devices ）； 2. In pairing mode,headset disconnect with phone and other devices,it will pair automatically Blue and red light is rapid flashing alternately After enter into the pairing mode, blue and red light alternately flashing,it will last for 2 minutes.Enter into pairing/YEJ warning voice Power off In On mode,touch the magnet together,it will power off Red and blue indicator light will flash ,it will last for 1 second YEJ warning voice Last Number Redialing Pree MFB for twice;If in 2 link status,then press and hold “+”volume key for 2 seconds Aim at redialing the last phone number that you called (your phone must be supported with Bluetooth redialing mode Answering the call 1.听In On mode,shortly press MFB ； When in On mode ,could not use the magnetic function to answer the call 2. In off mode ：Requirement:headset must be have pairing record with the phone When a call coming,pull apart the magnet,it will pair with the phone again ,if successful,could answer the call automatically Can answer the call through the headset In music state ,press MFB to answer the call. If use the magnetic function to end the call ,music will transfer to your phone. (Recommend not use the magnetic function to end the call under such condition) (End the call) 1.Shortly press MFB 2.Touch the magnet together ,at the same When you want to cut off the call Beep once FCC ID: 2AEEVOBFTC-0010-ABS156RLIC: 20048-OBFTC0010A
Otter Products, LLC. OBFTC-0010-A Page 2 of 2 time, headset will power off. Rejecting call Press and hold MFB for 2 seconds(In pairing mode) Directly rejecting the incoming call Could hear beep twice ,and headset will enter into standby mode(you phone need to support it) Mute Press and hold “V+” button for 3 seconds The caller won’t hear the sound from headset Could here Beep twice Two link function Separated twice to Connected with 2 phone Connected with two phone at the same time, enter into standby mode your phone need to support Music play /stop 1.In standby mode, shortly press MFB 2. touch the magnetic to pause music and power off 3. pull apart magnetic for playing music On music state Led shining once on every 10 second forward Long press V- for 2 second on music state With voice guidance of “dou” backward Long press V+ for 2 second on music state With voice guidance of “dou” Ring for coming call No need any operation It should support by phone sirr On music state, shortly press V+ AND v- at the same time automaticed by cellphone(voice dial) it should support by phone Clear pairing list Without connection state. Long press V+ and V- until the red and blue light flashed twice at the same time, then power off for clearing pairing list red and blue light flashed twice at the same time Voice guidance with “dou do” 1.Some function will differ due to phone’s brand 2.For the Aptx function, it should be supported by phone with aptx BS156RL
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and(2) this device must accept any interference, includinginterference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre lefonctionnement.

Navigation menu