Ox Co OPMW Microwave Module User Manual PCB Outline

Optex Co Ltd Microwave Module PCB Outline

User MAnual

Operation Manual 1. Scope 2. Note and Warning 3. Electrical Specification 4. Pin Assignment 5. FCC Statement & IC Statement
1. Scope This module is designed for motion sensing applications. It consists of Oscillator, Mixer, Filter, detecter and 2element Antennas(T), 2element Antennas(R). In addition, It have Frequency adjustment, Maintenance structure and Shield case. 2. Note and Warning The product is wireless device.It can radiation and receive RF signal. These electric equipments are very sensitive for RF signal in airplane,hospital,and place to life relate. The electric equipments almost interference from RF signal if it not shelter enough and flaw in design. In order to avoid damage for life and property,in compliance with standard of ever place and electric equipment to use the product. If the product collide,operate improper,and maintain by oneself. We are not indemnification. Place responsibility by oneself. The product need solder a By Pass Capacitor in 22~100nF on DC +5V supply point of the main PCB. The value of By Pass Capacitor is for reference. Determination of value must according to require of your system. 3. Electrical Specification Operating Voltage 5.0±0.2 V dc Operating Current 35mA typ. (CW operation) Center Frequency 10.525GHz typ. Frequency Stability ±5 MHz max. (-30 to +65℃) Output Power 20mw (E.I.R.P.) max. Second Harmonic Emission 1μW max. Antenna beamwidth (-3dB) E-Plane H-Plane 70 deg. nom. 40 deg. nom.
4. Pin Assignment 1. +5V 2. GND 3. IF out
5. FCC Statement & IC Statement FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID:DC9OPMW ". If the size of the end product is larger than The end user has to be informed that the FCC radio-frequency exposureguidelines for an uncontrolled environment can be satisfied. The end userhas to also be informed that any changes or modifications not expresslyapproved by the manufacturer could void the user's authority to operate thisequipment. The FCC part 15.19 statement below has to also be available inthe manual: This device complies with Part 15 of FCC rules. Operation issubject to the following two conditions: (1) this device may not cause harmfulinterference and (2) this device must accept any interference received,including interference that may cause undesired operation.
8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. For MPE Statement – Mobile device IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX IC :4012A-OPMW ". The end user has to be informed that the IC radio-frequency exposureguidelines for an uncontrolled environment can be satisfied. The end user hasto also be informed that any changes or modifications not expressly approvedby the manufacturer could void the user's authority to operate this equipment.IC statement is required to be available in the users manual: This Class Bdigital apparatus complies with Canadian ICES-003. Operation is subject tothe following two conditions: (1) this device may not cause harmfulinterference and (2) this device must accept any interference received,including interference that may cause undesired operation.

Navigation menu