Ox Co RC-20U CHIME BOX WITH RELAY RECEIVER User Manual RC 20U IM p1 Black A4 150110r

Optex Co Ltd CHIME BOX WITH RELAY RECEIVER RC 20U IM p1 Black A4 150110r

User manual

2000Transmission range must be changed according to environment.Please check if system works properly for the site.In the case of insufficient transmission range, use TR-20U (Repeater unit) to extend its range.Receiver/ RepeaterRC-20U/ TR-20USensor unitTD-20URepeaterTR-20UContact unitTC-10UButton unitTS-10URC-20U INSTALLATION INSTRUCTIONS CHIME BOX W/RELAY RECEIVERPlease read this manual carefully before installation.2 PARTS IDENTIFICATION1 CAUTION AND WARNING4 INSTALLATION 5 POWER CONNECTION6 TEACH TRANSMITTER CODES TO RC-20U “LEARN MODE”3 TRANSMISSION RANGE (REFERENCE)2000ft (Open field, line of sight)150ft (Stucco/Plaster construction)100ft (Concrete construction)1400ft (Open field, line of sight)150ft (Stucco/Plaster construction)100ft (Concrete construction)Wall MountingUse the mounting screw on a wall. Leave some length of the screw out for mounting hole of the RC-20U.Desktop Pull out the stand on the back of the RC-20U and place it on any flat surface. Remove the connection terminal cover. Use the terminal marked “COM-N.O.” for N.O. devices and “COM-N.C.” for N.C. devices. Remove knockouts according to wiring needs. Close the connection terminal cover. Each transmitter has a unique transmitter code which can be automatically learned by RC-20U.The RC-20U’s zones must be taught to respond to the appropriate transmitter. (No transmitter is taught on default setting.)Note:・ Verify that each transmitter has been successfully learned by RC-20U by triggering them.・ Each zone can learn max. 3 transmitters.・ Zone indicator shows the activated transmitter by the number of flash. (e.g. If learned second transmitter in zone 1 is activated, zone 1 indicator flashes twice.)・ Single transmitter cannot be learned by multiple zones・ RC-20U learned code will keep memorized even if turning OFF the power. A) The RC-20U automatically starts in “LEARN MODE” if no transmitter code has been programmed.ORB) Press and hold switch 1 until the power indicator starts to flash.Use only the power adaptor supplied with the product. Terminal connectionAny device with a zero voltage input terminal can be connected to this terminal. This may include electronic locks, emergency sounding devices, and automatic reporting equipment.CAUTION1. Impact/Shock Impact or Shock can cause severe damage or break the RC-20U.2. Electric Devices Use RC-20U at least 3ft (1m) away from electronic devices such as TVs, Radios, PCs, Microwave ovens, or any other devices with an electric motors. This may cause the unit to malfunction.3. Transmission range Transmission range may decrease under the following conditions: - Either transmission units or RC-20U installed on a metal surface. - Presence of a steel door, reinforced concrete or other metal obstructions between transmission units and RC-20U. - Places near strong radio sources such as broadcast stations or substation.4. Cleaning Harsh cleaners such as paint removers or benzene may ruin the surface. Use a soft wet cloth and mild soap to clean.WARNING1. Harsh environments Do not use the RC-20U outdoors, severe conditions as out of warranted temperature, rapid temperature change, high humidity, or steam. This may cause the unit to malfunction.2. Tampering Any changes or modifications not expressly approved by OPTEX could void the user’s authority to operate the equipment.3. Adaptor Do not use any other AC adaptor except what is included.Mounting holeStandConnection terminalcoverOutput connection terminal(Inside of the cover)FRONTNote: When you recycle this product, please disassemble product and recycle according to state law.BACKZone indicator 1Zone indicator 2Zone indicator 3Switch 1Switch 2Adaptor JackPowerSwitchPower indicatorSpeakerFunctionAC AdaptorMounting screwSwitch 1 Activating “LEARN MODE” and“TERMINAL OUTPUT DURATION MODE”.Activating “VOLUME ADJUSTMENT MODE” and making selection.Switch 2Activate “LEARN MODE” Teach the transmitter code to RC-20UZone 1 Zone 2 Zone 3 Zone 4(Special/ refer 8 )Normal Operation StatusThe corresponding zone indicator flash rapidly at interval’s of 1 sec according to the related transmitter.Activate the transmitter you wish to teach the receiver.((Receiver startsin Zone 1. Press switch 2 to advance to the next zone and chime sound. Press switch 2 to return to normal operation status.BlinkLightFEATURES・ Compatible with TD-20U (Indoor/Outdoor Sensor Transmitter),TS-10U (Hand-Held Transmitter), TR-20U(Repeater), TC-10U(Door/Window Transmitter) and any transmission units of WIRELESS1000 series.・ Identifies 4 zones by 3 different tones and LED lights (3 normal zones + 1 continuous zone).・ Able to learn 12 transmission codes (Each zone can learn 3 transmitters maximum). ・ Automatic “Learning” function facilitates to preset transmission codes to RC-20U.・ Over 8 million codes possible, eliminates interference from neighbors.・ Latches into alarm with “Continuous mode” function.・ Programmed ”Utility Output Mode” to inactivate chime tone (applicable for zone 3).・ Adjustable duration for terminal output. ・ Adjustable volume.・ Low battery indicator to recognize transmission units’ battery status. ・ Powered by a 9VDC adaptor(Included).Erasing codes from RC-20U’s memory.1) Hold down switch 1 until the power indicator starts to flash.2) Press switch 2 until the appropriate zone indicator is lit.3) Press switch 1 to erase. The zone indicator will start to flash. (Note: All programming in that particular zone will be erased.)4) Press switch 2 a few times until the power indicator stops flashing and remains lit.Erasing all codes from RC-20U. (Return to the factory default)To erase all programming, turn on power while holding switch 1.
Unit: inches (mm)1. The system is not operatingCheck the transmitter.Does the status indicator light up when you trigger the transmitter?Check to see whether the battery is inserted correctly. If the battery is old, replace it with a new one.Is the status indicator of the transmitter flashing? The battery is old. Replace the battery.Check the receiver.Is the power indicator of the RC-20U lit? Is the receiver on? Check the wiring and connection.Have all the transmitter codes have been taught correctly? Teach the transmitter codes correctly. The system will not operate without this process. Is the volume setting correct? Is the volume set to “0”? If so, readjust the volume.Are there other high power appliances using thesame electrical power outlet? Please connect the RC-20U to a different electrical outlet.The zone indicator of the RC-20U is on, but nothing happens.Check to see whether the terminal is properly connected to other devices. Are the zone indicators flashing slowly? Follow directions in 10 LOW BATTERY INDICATION.Is there anything blocking the transmission? Relocate the receiver and/or the RC-20U. Metal objects can shorten the effective transmission range.2. The system is not operating correctly.The RC-20U does not learn the transmitter codes. The RC-20U gets reception in the wrong zone. Check whether the transmitter codes have already been learned in a different zone. If so, erase the memory and teach again.Erase memory in the zone in which the RC-20U responds and teach using the correct zone. The RC-20U does not respond to some of the transmitters.You may have taught multiple transmitter codes in the same zone. Teach the transmitter codes for which no response is received using an empty zone.A certain zone seem to malfunction.This is probably the transmitter’s problem. Check the transmitter that corresponds to that zone.Before contacting the supplier! Go through the setups again after turning on the power while holding down switch 1.• If the above solutions do not work, please contact your supplier for services.Model DescriptionPower Source Chime ToneVolumeRelay outputOutput TimerFrequency Operating TemperatureInstallation LocationRC-20UChime Box w/Relay Receiver3 Tone & Continue Zone (Selectable)9VDC (Exclusive AC Adaptor)Power Consumption 8W Max. (Including AC Adaptor 120V, 60Hz)Adjustable: 0~80dB/ 5 levelsSelectable: Off/1/5/30/60sec/ Utility output modeStatus IndicatorPower Indicator: GreenZone Indicator: Red x 3Form “C” MAX 1A/50VAC 24VDC418MHz15° F ~ 105° F (-10°C ~ +40°C) IndoorAccessories Mounting Screw × 1. AC AdaptorWeight 6.0 oz (170g)Specifications may change without notice7 VOLUME ADJUSTMENT8 TERMINAL OUTPUT DURATION ADJUSTMENT9 TROUBLESHOOTING 10 LOW BATTERY INDICATION11 SPECIFICATION 12 DIMENSIONS14 WARRANTY13 COMPLIANCE1. This product is warranted under normal use for 2 years from the date of purchase. If the product proves to be defective, return it with a copy of your dated sales receipt for repairs or replacement without charge.2. The warranty is not applicable when below circumstances will be found: • Mechanical or electrical modification(s) are made to the product or it is otherwise altered manually. • The product is already been serviced at place(s) other than the manufacturer. • It is determined that the product malfunction has resulted from improper use or from an accident. • No copy of the dated sales receipt has been submitted together with the product to be serviced.FCC ID : DC9RC-20UThe changes or modifications not expressly approved by the OPTEX could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter.Note: This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.(1)Reorient or relocate the receiving antenna. (2)Increase the separation between the equipment and receiver.(3)Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.(4)Consult the dealer or an experienced radio/TV technician for help.IC ID : 4012A-000000TD20UOperation is subject to the following two conditions.(1)this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.3.5 (88)1.1 (28)7.4 (188)5.3 (134)This adjustment is applicable for zone 1 to 3 as a group and zone 4 independently. There are volume setting from Level 0 to 4. (Default setting for zone 1-3 is level 3, for zone 4 is level 4.) 2 modes can be set according to the application. Press switch 2 for 1 time to activate “VOLUME ADJUSTMENT MODE” for zone 1-3 or hold switch 2 for 5 seconds for zone 4. (Power indicator goes OFF and zone indicators display the current setting).RC-20U will automatically return to normal operation status after 5 seconds without any operation. (Zone indicators will go OFF and power indicator will remain lit.)LouderPress switch 2 to change volume level (Level 4 is the loudest.) Level 0 Level 1 Level 2 Level 3 Level 4Normal Operation StatusRC-20U will automatically return to normal operation status after 5 seconds without any operation. (Zone indicators will go OFF and power indicator will remain lit.)Press switch 2 to change duration time and setting. NO OUTPUT 1 SEC. 5 SEC. 30 SEC. 60 SEC. UTILITYOUTPUT MODENormalOperation StatusUtility Output modeRegular modeZone 1 Chime tone 1 Terminal output(Time duration according to setting)Continuous tone and terminal output(Latches until switch 2 is presses to inactivate.)Note: Time of the chime will not change according to terminal output duration adjustment.Chime tone 2Chime tone 3Zone 2Zone 3Zone 4Zone 1 Chime tone 1 No terminal outputTerminal output for only 5 sec.Continuous tone and terminal output(Latches until switch 2 is presses to inactivate.)Note: Time of the chime will not change according to terminal output duration adjustment.Chime tone 2No chime Zone 2Zone 3Zone 4Press switch 1 twice within 2 seconds to activate “ TERMINAL OUTPUT DURATION MODE” (zone indicators display the current setting).Zone indicator start slow flashing and sound a chime followed by 2 beeps whenever the corresponding transmitters have low battery. Any operation cannot be done until one of operations below are conducted. 1) Replace transmitter’s batteries. 2) Press switch 2. RC-20U will not need to relearn transmitter after replacing the batteries.Note: Check low battery status at the correspondingtransmitter in case several units are learned in 1 channel. 5916470

Navigation menu