User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1049634 |
| Application ID | 9PiCMnyYu+jqCfvmP5+dnA== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 96.02kB (1200242 bits) |
| Date Submitted | 2008-12-24 00:00:00 |
| Date Available | 2008-12-24 00:00:00 |
| Creation Date | 2008-12-11 13:03:40 |
| Producing Software | Adobe PDF library 5.00 |
| Document Lastmod | 2008-12-23 17:13:38 |
| Document Title | User manual |
| Document Creator | Adobe Illustrator 10.0 |
1000 FEATURES • Compatible with RC-10U (Chime Box W/Relay), RG-10U (Single Relay Receiver) • Can be installed on Door/Window. • Weather proof structure (IP54) for indoor and outdoor where don’t have rain direct. • Over 8 million codes possible, eliminates interference from neighbors • Powered by CR123 3-Volt lithium battery (not included) • Low battery signal • Two unique functions; the first is for its built-in magnet switch and the second is input terminal for the OPTEX’s battery operated detectors. TC-10U DOOR/WINDOW TRANSMITTER This product is only compatible with Wireless 1000 series. TC-10U MANUAL Please read this manual carefully before installation. CAUTION Please be careful of the following: 1. Outdoor Use The TC-10U Transmitter is suitable for both indoor and outdoor where don’t have rain direct. 2. High Temperature, High Humidity & Dirty Fumes Do not expose the TC-10U to high temperatures, rapid temperature changes, steam, high humidity, dirty fumes or oily smoke. 3. Transmission range may decrease under following conditions. • A steel door, reinforced concrete, or other metal obstructions between the TC-10U and the receiver. • Installing either the TC-10U or the receiver on a metal surface. • Places near strong radio sources such as a broadcast stations or high power lines. • To comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. The changes or modifications not expressly approved by the party responsible 4. Other Electric Devices Use the TC-10U at least 3ft (1m) away from following devices: TV, radio, personal Computer, microwave oven, refrigerator, and any device that has an electric motor (This may cause malfunction). 5. Impact/Shock Do not drop the TC-10U or give it a strong impact/shock. 6. Tampering The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 7. Battery Replacement Replace the battery every 2 years. Use only CR123 3V lithium battery. 8. Cleaning Harsh cleaners such as paint remover or benzene may ruin the surface. Use a soft, wet cloth and mild soap or detergent to clean. for compliance could void the user's authority to operate the equipment. PART IDENTIFICATION TRANSMITTER UNIT MAGNET UNIT TRANSMITTER UNIT Front cover Screw hole (for mounting) Knockout (for mounting) Slide switch (for select function) Status indicator Input terminal Front cover magnet box Battery Rear cover magnet box Wall plate MAXIMUM TRANSMISSION RANGE OPERATING CONDITION It transmits when the door opens or when the transmitter unit is removed from the wall plate. TC-10U Door/ Window Wall • Use only CR123 3V lithium battery 700ft. (open field, line of sight.) Measurements were made over level ground without obstruction. Natural or man-made obstacles and other environmental factors can interfere with or otherwise reduce transmission range. Always confirm actual transmission range during installation of system. Please use the information below as a reference for transmission performance. 110ft Plaster construction: It transmits when the distance of the magnet unit from the transmitter unit is as shown. Reinforced concrete construction: 0.40 ~ 1.18 (10 ~ 30) 0.16 ~ 0.40 (4 ~ 10) 70ft 0.32 ~ 0.79 (8 ~ 20) Unit: inches (mm) When using OPTEX’s battery operated detector Lead the wire from OPTEX’s battery operated detector into the input terminal. Move the Slide switch to input terminal for change function. Wiring knockout Remove the wiring knockout as shown. * It will lost weatherproof structure. * Put in these detectors’s backbox. * About these detectors, please contact your supplier for services. INSTALLATION BATTERY 1. Remove the Front cover as shown. 2. Insert batteries. Observe polarity. (+/- direction) 3. To replace the cover. • When the power is low, Status indicator starts flash. Replace the battery in such case. • Low power may become the cause of false alarm. • There is no need to readjust the TC-10U nor the receiver after replacing battery. • Don’t throw the battery in the fire because there is the explosion hazard. *confirm its closed surely TEACH TRANSMITTER CODES TO THE RECEIVER The receiver must be taught this TC-10U’s unique code before use. Refer to the receiver’s manual for details. 1. Preparation 2. Activation 3. Verification • Separate the magnet unit from transmitter unit. • Verity that the receiver has learned successfully by observing the zone indicators of the receiver. Zone indicators should have stopped flashing and remain continuously on. • Press Switch 1 of the receiver until the power indicator starts flashing. • Press switch 2 to select the zone you wish to assign to the sensor. Note: • After teaching all the transmitter’s codes (if you have multiple transmitters), return the receiver to normal operating status. • Make sure that the receiver operates correctly with all the transmitters. INSTALLATION Cover the TC-10U until you are ready to teach the receiver. Unwanted detection can cause the TC-10U to be assigned to the wrong zone and override the data of other transmitters. CONFIRMATION Double stick tape installation After installation, door/window open and close. And confirm the receiver weather it is received. Clean the installation positions before Wall Door/ Window installing them. Install the transmitter unit on the wall. Install the magnet unit on the door or window. *Align the magnet unit within 0.2 inch (5 mm). Screw installation Wall knockout Door/ Window Rubberwasher SPECIFICATIONS Model Description Status Indicator Power Source Battery Life Frequency Input terminal Operating Temp. Installation Location Accessories Weight TC-10U Door/Window Transmitter Red LED 3V:CR123 lithium battery (not include) 2years [100 times per day at 70°F (20°C)] 418MHz Our battery operated detector only 15°F ~ 120°F (-10°C ~ +50°C) Indoor / Outdoor where don’t have rain direct. Double stick tape × 3, Screw × 4, Rubber Washer × 2 2.5oz (70g) (not included battery) Specifications may change without notice DIMENSIONS To put back the cover. 1.5 (36.7) Install the transmitter unit on the wall with rubber washer and mounting screws (two places). Install the magnet unit on the door or window with mounting screws. Unit: inches (mm) *If it is without rubber washer, it will lost weatherproof structure. *Align the magnet unit within 0.2 inch (5mm). 3.1 (79) TROUBLESHOOTING 0.85 (21.7) Put the double stick tape as shown. 1. The system is not operating. Is the status indicator flashing? If not, check to see if the battery is inserted correctly. Otherwise try a new battery. The magnet unit away by enough distance? Please separate it by 0.6 inch (15 mm). The battery is old. Replace the battery. Check the receiver (or repeater). Is the power indicator of the receiver lit? The receiver does not respond to the TC10U. The zone indicator of the receiver is on, but nothing happens. Is there anything blocking the transmission? Is the receiver on? Check the wiring, power switch and connection. The TC-10U is not properly recognized by the receiver. Teach the receiver correctly. Receiver has not been properly setup. Refer to the receiver’s manual and verify the setting. Relocate the receiver and/or the TC-10U. Metal objects can shorten the effective transmission range. 2. The system is not operating correctly. It does not transmitting. Before contacting the supplier! Does it makes between Transmitter unit and Magnet unit within 0.2 inch (5 mm)? Is its distance more than transmission range to receiver? Please use repeater. Remove the battery, then reinsert the new batteries and verify the TC-10U’s operation again. • If the above solutions do not work, please contact your supplier for services. 1.8 (45) 0.6 (15) 1.0 (24) 0.95 (24.2) Does the status indicator light up when you remove transmitter unit from wallplate? 0.95 (24.2) Check the transmitter. LIMITED ONE-YEAR WARRANTY (1) This Sensor Transmitter is warranted to the original consumer purchaser to be free from defects in material and workmanship under normal use for one (1) year from the date of purchase. If the product proves to be defective, return it postage prepaid with a copy of your dated sales receipt for repairs or replacement without charge. (2) This warranty is in lieu of any and all other warranties, whether expressed or implied, including but not limited to any warranty of merchantability or fitness for a particular purpose. (3) This warranty is invalid under the following circumstances: • Mechanical or electrical modification(s) are made to the product or it is otherwise altered manually. • The product is already been serviced at place(s) other than the manufacturer. • It is determined that the product malfunction has resulted from improper use or from an accident. • No copy of the dated sales receipt has been submitted together with the product to be serviced. OPTEX CO., LTD. (JAPAN) (ISO 9001 Certified) (ISO 14001 Certified) 5-8-12 Ogoto Otsu Shiga 520-0101 JAPAN TEL:+81-77-579-8670 FAX:+81-77-579-8190 URL:http://www.optex.co.jp/e/ OPTEX INCORPORATED (USA) OPTEX SECURITY Sp.z o.o. (POLAND) OPTEX (EUROPE) LTD. (UK) OPTEX KOREA CO., LTD. (KOREA) TEL:+82-2-719-5971 TEL:+1-909-993-5770 Tech:(800)966-7839 URL:http://www.optexamerica.com TEL:+48-22-598-06-55 URL:http://www.optex.com.pl TEL:+44-1628-631000 URL:http://www.optexeurope.com URL:http://www.optexkorea.com OPTEX SECURITY SAS (FRANCE) TEL:+33-437-55-50-50 URL:http://www.optex-security.com OPTEX (DONGGUAN) CO., LTD. SHENZHEN OFFICE (CHINA) TEL:+86-755-33302950 URL:http://www.optexchina.com 0851Q 5915570
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print Modify Date : 2008:12:23 17:13:38+08:00 Create Date : 2008:12:11 13:03:40+10:00 Creator : Adobe Illustrator 10.0 Page Count : 2 For : y, C-and-F Title : C:\2008_DATA\CFAVXg˗2008\0810-1202\ƒ\W1000-TC-10U_081202\TC-10U_p1.eps Bounding Box : 27 29 1074 1174 Container Version : 9 Creator Version : 10 About : uuid:1b69d936-9173-40f6-9f6d-ac27cc5f3144 Producer : Adobe PDF library 5.00 Creation Date : 2008:12:11 13:03:40+10:00 Mod Date : 2008:12:23 17:13:38+08:00 Creator Tool : Adobe Illustrator 10.0 Metadata Date : 2008:12:23 17:13:38+08:00 Document ID : uuid:591e7cd5-9714-431d-9104-b0f3e3f5f247 Instance ID : uuid:e06a2b73-8703-4b46-89c3-fe1c5e02af96 Format : application/pdf Has XFA : No Image Height : 1145 Image Width : 1047 Image Size : 1047x1145 Megapixels : 1.2EXIF Metadata provided by EXIF.tools