Users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 68602 |
| Application ID | n3Gup8ulNcqViWCRMzk4HA== |
| Document Description | Users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 2.14kB (26745 bits) |
| Date Submitted | 1999-11-08 00:00:00 |
| Date Available | 2000-02-25 00:00:00 |
| Creation Date | 2001-05-18 15:04:28 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-05-18 15:04:29 |
| Document Title | Users manual |
INTERNATIONAL Data Sheet October 1999 17XXX Ver 1.0 20447-2 KeyPAC Desktop Reader Installation Instructions Description The KeyPAC PC Desktop Reader is an accessory for use with a PAC Adminstration interface unit. This system is used for direct PC to controller communications (fig. 1). Note: This Desktop Reader will read KeyPAC ID-devices including ISO thickness ID cards. It will not read the earlier PAC ID devices. Always specify KeyPAC when you buy ID devices. Note: It is unlikely that you will need an Interface Kit at a PC that already has a KeyPAC CNC attached. CNCs have front panel readers, which can also be used for administration. WARNING: The Interface Unit contains mains voltages. This procedure should only be carried out by a suitably qualified and experienced person. If you have any doubts as to your suitability contact PAC for advice. Failure to do so may result in injury or death by electric shock. WARNING: If, at any time, the interface kit or its wiring appear damaged then immediately disconnect it from the mains and contact PAC for advice. Failure to do so can result in electric shock and/or further damage to equipment. KeyPAC 17 Ver 1.0 Installation Opening the Interface Unit WARNING: This Interface Unit contains mains voltages. Before opening ensure that it is disconnected from the mains. Failure to do so can result in injury or death by electric shock. Make sure that the Interface Unit is not connected to the mains then remove the lid by removing the 4 screws recessed in the base. There are removable terminal blocks fitted to the circuit board as shown below: Connecting the Desktop reader The Desktop reader supplied with the kit is complete with cable and terminal block. Fit the terminal block with the screw heads facing the centre of the interface unit, and route the cable through the grommet provided. Wiring for provided cables - for information only KeyPAC Desktop Reader to Interface 1.5m cable supplied. KeyPAC PC Interface Desktop Reader 4-pole Terminal Block -V VCA SIG +V Page 2 KeyPAC Desktop reader ———— ———— ———— ———— -V VCA SIG +V DRAFT Green Yellow White Brown ©1999 PAC International Ltd. KeyPAC 17 Ver 1.0 Specification Dimensions 5.12in x 3.54in x 1.25in Voltage 10.5v DC to 20v DC (Supplied by Administration Interface Unit) Current Idle: 10-20mA Reading: 10-20mA Operating: -10°C to +55°C (14°F to 130°F) Storage: -30°C to +80°C (-20°F to 175°F) Humidity Operating: 0-90% RH at 30°C ±2°C (85°F±5°F) for 24 hours Reading Range 0-2 inches Lead Length 56 inches Temperature This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID OQL-PAC-DT Page 3 DRAFT ©1999 PAC International Ltd.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:05:18 15:04:28 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:05:18 15:04:29-04:00 Page Count : 3EXIF Metadata provided by EXIF.tools