PAC R-VN Vandal Resistant Reader User Manual T81153 14104 Readers
PAC International Limited Vandal Resistant Reader T81153 14104 Readers
PAC >
Manual
T81153v2.2 14104 Mar 05 Designer and Vandal-Resistant Readers Installation Guide Designer und Vandal-Resistant Lesers Installationsanleitung Designer et Vandal-Resistant Lecteurs Guide d'installation Designer y Vandal-Resistant Lectores Guía de instalación Designer och Vandal-Resistant Läsare Installationsanvisningar Designer en Vandal-Resistant Lezers Installatiehandleiding Reader Part Numbers / Leser Teilnummern / Numéros de pièces du lecteur / Números de pieza del lector / Läsarens Artikelnummer/ Lezer Productnummers black/ schwarz/ noir/ negro/ svart/ zwart grey/ grave/ grise/ grid white/ weiß/ blanc/ blanco/ vit/ wit Mullion Designer 21N-MPRBLACK 21N-MPRGREY 21N-MPRWHITE Standard Designer 21N-SPRBLACK 21N-SPRGREY 21N-SPRWHITE Vandal-Resistant 21N-VPR-SS Card/Token Part Numbers / Karten/Token Teilnummern / Numéros de pièces de carte/fiche / Números de pieza de la tarjeta/ficha / Kort/Nyckel Artikelnummer / Passen/Penningen Productnummers Card/Karten/Kort/Passen x10 11N-PT-10 With Magstripe//Mit Magnetstreifen/avec bande magnétique/ Con banda magnética/med magnetremsa x10 11N-MPT-10 Token/Nyckel /Penningen x10 11N-FPT-10 Specification / Spezifikation / Spécification / Especificaciones / Specifikation / Specificaties / 技术规格 Card Range Token Range Power Current Mullion Designer up to 3.5in/90mm up to 1.9in/50mm +10.5 to +28V <100mA Standard Designer up to 7.8in/200mm up to 1.9in/50mm +10.5 to +28V <100mA Vandal-Resistant up to 1.9in/50mm up to 1.9in/50mm +10.5 to +20V <85mA Temperature / Temperatur / Température / Temperatura / Temperatur / Temperatuur Operating -3 to 130ºF/-20 to +55ºC; Storage -35 to175ºF/-30 to +80ºC Humidity / Feuchtigkeit / Humidité / Humedad / Luftfuktighet / Vochtigheid Operating 10 to 85% RH at 85 ± 4ºF/30 ± 2ºC for 24 hours Ingress Protection / Eindringschutz / Protection contre l'entrée / Protección de acceso / Kapsling / Stofbescherming IP 66 FCC Mullion Designer FCC ID OQL-R-DM This device complies with part 15 of the FCC Rules. Operation Standard Designer FCC ID OQL-R-DS is subject to the following two conditions: (1) This device may Vandal-Resistant FCC ID OQL-R-VN not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. In compliance with FCC requirement 15.27 no special accessories are required in order to comply with part 15 of the FCC regulations. Changes or modifications not expressly approved by Stanley Security Solutions could void the user's authority to operate the equipment. T81153v2.2 Connections/ Anschlüsse / Connexions / Conexiones / Anslutningar / Voedingsaansluitingen All dimensions ins/mm / Alle Ausmaße in zoll/mm / Toutes dimensions en pce/mm / Todas las dimensiones en pulg./mm /Alla mått i tum/mm / Alle afmetingen inch/mm Mullion Designer 10.5-28V (10.5-20V for Vandal-Resistant) SIG/D1/DATA/SIGNAL LED GND/0V D0/CLK Tamper/Sabotage/Effraction/Manip.fraud./Manip/Tamper Sounder/Signaltongeber/ Alarme sonore/Sonido/Ljudsignal/Alarm H Not used/Nicht verwendet/N'est pas utilisé/ No se utiliza/Används inte/Niet gebruikt Standard Designer Vandal-Resistant Red/Rot/Rouge/Rojo/Röd/Rood White/Weiß/Blanc/Blanco/Vit/Wi Brown/Braun/Marron/Marrón/Brun/Bruin Black/Schwarz/Noir/Negro /Svart/Zwart Green/Grün/Vert/Verde/Grön/Groen Blue/Blau/Bleu/Azul/Blå/Blauw Yellow/Gelb/Jaune/Amarillo/Gul/Geel Output Format Selection / Wahl des Ausgabeformats / Sélection de format de sortie / Selección de formato de salida / Val av utdataformat / Selectie van uitvoerformaat Connections/Anschlüsse/ No. of flashes/ Zahl der Blinkvorgänge/ Verbindingen/Conexiones/ Nb. de clignotements/ Núm. de Anslutningar/ Connexions destellos/Aantal flitsen/ Antal blinkningar Stanley (default/vorgabe/ C-B standaard/por defecto) Wiegand 26-bit C-E Wiegand 34-bit C-B G-E Magstripe/gnetstreifen/ G-E magnetremsa Barcode C-E G-B T81153v2.2 English Installation 1. Ensure your product comes with the items indicated on page 2; if not please contact your dealer. 2. Mounting on metal surfaces will reduce the reader range. 3. Mount readers >3ft/1m apart. 4. For outside readers, use corrosion-resistant fasteners and silicone sealant on terminals. 5. The Metal Oxide Varistor (MOV) should be fitted across the power terminals of the lock. 6. After installation of a Designer Reader, fill the connector well with silicone to seal it. Stanley recommend a high-quality sealant like Dow Corning Type 732. Output Format Selection 1. Short together the connections indicated in the table on page 3. 2. Apply power for 2 seconds 3. Separate all connections. 4. Re-apply power. 5. LED flashes to indicate ouput format set in the table on page 3. Deutsch Installation 1. Überprüfen Sie, ob Ihr Produkt die einzelteile angezeigt auf Seite 2. Wenn nicht, wenden Sie sich bitte an Ihren Händler. 2. Die Befestigung an den Metalloberflächen verringert die Leserstrecke. 3. Leser im Abstand von > 3 Fuß/1 m anbringen. 4. Für Leser im Freien korrosionsbeständige Befestigungselemente und Silikondichtungsmittel an den Anschlüssen verwenden. 5. Der MOV sollte über die Stromanschlüsse des Schlosses angebracht werden. 6. Nach der Installation von einnem Designer Leser, den Stecker vollständig mit Silikon füllen, um ihn zu versiegeln. Stanley empfehlen ein hochwertiges Dichtungsmittel wie Dow Corning Art 732. Wahl des Ausgabeformats 1. Die Anschlüsse wie auf der nachfolgenden Tabelle angegeben auf Seite 3 miteinander kurzschließen. 2. 2 Sekunden lang Strom anlegen. 3. Alle Anschlüsse trennen. 4. Nochmals Strom anlegen. 5. Die LED Blitze, zum des ouput Formats anzuzeigen stellten in die Tabelle auf Seite 3 ein. Français Installation 1. Vérifiez que votre produit contient toutes les articles indiqués à la page 2. En cas de pièce manquante , contactez votre distributeur 2. Le montage sur des surfaces en métal réduira la gamme de lecteur. 3. Monter les lecteurs à de telle sorte qu'ils soient espacés d'1 m. 4. Pour les lecteurs extérieurs, utiliser des fixations résistantes à la corrosion et du silicone sur les bornes. 5. Le MOV (varistor à oxyde métallique) doit être installé en travers des bornes d'alimentation du verrou. 6. Après l'installation d'un Designer Lecteur, bien remplir le connecteur de silicone pour l'étanchéiser. Stanley recommandent un mastic de haute qualité comme le Dow Corning type 732. Sélection de format de sortie 1. Court-circuiter les connexions indiquées dans le tableau à la page 3. 2. Mettre sous tension pendant 2 secondes. 3. Séparer toutes les connexions. 4. Mettre à nouveau sous tension. 5. Les flashes de LED pour indiquer le format d'ouput ont placé dans la table à la page 3. T81153v2.2 Español Instalación Asegure que el producto se suministra con los artículos artículos indicados en la página 2; en caso contrario, rogamos que se ponga en contacto con el vendedor. 1. El montar en superficies del metal reducirá la gama del lector. 2. Monte los lectores a una distancia entre sí >1 m. 3. Para los lectores exteriores, utilice fijaciones anticorrosivas y sellador de silicona en las terminales. 4. El varistor de metal-óxido se debería montar a través de los terminales de potencia de la cerradura. 5. Tras la instalación de un Designer Lector, rellene bien el conector con silicona para sellarlo. Stanley recomiendan un sellante de alta calidad como el Dow Corning tipo 732. Selección de formato de salida 1. Puntee las conexiones que se indican en la tabla en la página 3. 2. Aplique potencia durante 2 segundos 3. Separe todas las conexiones. 4. Vuelva a aplicar potencia. 5. Los flashes del LED para indicar formato del ouput fijaron en la tabla en la página 3 Svensk Installation 1. Kontrollera att din produkt åtföljs artikeln antyd på sida 2. Kontakta din återförsäljare om. 2. Monteringen på metall utsidorna vilja reducera läsaren ställa i rad. 3. Montera läsarna mer än 1 meter isär. 4. För utomhusläsare ska korrosionståliga fästanordningar och silikontätningar användas på terminalerna. 5. Metalloxidvaristorn ska monteras över låsets spänningsanslutningar. 6. Fyll kontakten allra Design Läsare, ordentligt med silikon efter installationen för att täta den. Stanley rekommendera en hög - kvalitet sätta sigill på lik Dow Corning typ 732. Val av utdataformat 1. Kortslut anslutningarna som anges i tabellen på sida 3. 2. Aktivera spänningsmatningen under 2 sekunder. 3. Separera alla anslutningar. 4. Lägg på spänningsmatningen igen. 5. LED blinkar till ange ouput formaten sätta inne borden på sida 3. Nederlands Installatie 1. Controleer of met het product de punten die op pagina 2 worden vermeld. Indien dit niet het geval is, neem dan contact op met de leverancier. 2. Het opzetten op metaaloppervlakten zal de lezerswaaier verminderen. 3. Plaats de sensors minstens 1 m uit elkaar. 4. Voor sensors die buiten worden gemonteerd dienen corrosiebestendige bevestigingsmiddelen en een siliconen afdichtmiddel op de aansluitpunten gebruikt te worden. 5. Breng de MOV over de aansluitingen van het slot aan. 6. Na het installeren van een Designer Lezer, dient u de holte van het verbindingsmiddel met siliconenafdichtmiddel op te vullen. Stanley adviseert een dichtingsproduct van uitstekende kwaliteit zoals Dow Corning Type 732. Selectie van uitvoerformaat 1. Sluit de verbindingen aan volgens de tabel op pagina 3. 2. 2 seconden onder stroom zetten 3. Alle verbindingen losmaken. 4. Nogmaals onder stroom zetten. 5. De LED flitsen om ouput op formaat te wijzen plaatsen in de lijst aangaande pagina 3. T81153v2.2 6 T81153v2.2 T81153v2.2 Stanley Security Solutions, Inc. 6161 E. 75th St. Indianapolis, IN 46250 T: (317) 849-2250 Stanley Security Solutions - Europe Ltd Blick House Bramble Road Swindon, SN2 8ER T: +44 1793 692401 Stanley Security Solutions - Europe Ltd Blick France 15 rue du 1er Mai 92752 Nanterre Cedex T: 01 47 60 02 70 Stanley Technology Co Ltd 1/F, Building E Zone A Hongfa Industrial Park Shi Yan Bao'an District Shenzhen 518108 T: +86 755 29833111 © 2005 Stanley Security Systems, Inc. www.stanleysecuritysolutions.com Contact your local Stanley Security Solutions Systems Integration Office for Technical Support.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 8 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:3e5d1517-81d8-4f70-a4c4-64d2ee554fde Producer : Acrobat Distiller 6.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2005:03:24 10:39:23Z Create Date : 2005:03:24 10:39:23Z Document ID : uuid:d4b9cd47-5edb-40a6-8098-938e9dea1acc Format : application/pdf Title : Microsoft Word - T81153_14104_Readers.doc Creator : JohnF Author : JohnFEXIF Metadata provided by EXIF.tools