PAX Technology PX7W Multi-Lane Payment Terminal User Manual PX7 W fcc

PAX Technology Limited Multi-Lane Payment Terminal PX7 W fcc

User manual

Reset Button and Audio Jack7Reset Button and Audio Jack Mounting Slots ResetButton Audio Jack If required, restart the terminal by pressing in and holding the reset button for 2-3 seconds.Cable Lock8Cable LockIf required, insert customer-provided cable lock into K-Slot®. Loop cable around permanent object to secure in place.Stand Installation9Stand InstallationPAX TECHNOLOGY INC.Stylus PortIf required, a visually disabled person can connect a headphone to the terminal for audio prompting using the 3.5mm output audio jack.Route CablesxIf required, the P terminal may be mounted to a stand. Instructions may vary depending on stand specifications.Carefully route the required cables up through the stand pipe and out the top. Connect the cables to the xP terminal ports.Insert the three mounting slots on the underside of the terminal into the three metal prongs on the stand base.Slide the terminal firmly into position, locking the terminal in place on the stand. Secure with fastening screw or locking device as required.PAX TECHNOLOGY INC.PAX TECHNOLOGY INC.xP termi nals that include a default commu nication module come standard with one Et hernet port and RS 232, USB, and PU SB network capabilities. However, if the default commu nication mo dule is replaced with an optional commu nication mo dule, your choice of these additional netwo rk capabilities are available:Communication ModuleCommunication Module Power ConnectionsPower Connections3PAX TECHNOLOGY INC.Communication ports are labeled and color-coded:Green Blue Black Yellow Red WhiteProduct DescriptionProduct DescriptionStylus penTouch screenMagnetic stripe readerContactless readerPrivacy shieldKeypadSmart card readerCable retention clipsCommunication portsSpeakersMAC address labelRegulatory labelCommunication modulePart number/serial number labelPower can be supplied via the power port or a single data cable that carries power. This power can be provided via a “powered cable” where the connected POS terminal provides the powerx (i.e. PUSB or Power over Ethernet) or by connecting a P power supply directly to the data cable (i.e. RS232 or USB). 1) Power PortInsert the power connector into the green POWER port. Turn the power connector, locking the tab behind the short plastic wall.Dress the cable through the retention clips. A separate data cable is also required.2) POS CableInsert the cable connector into the appropriate port on the terminal. Dress the cable through the retention clips opposite the port. Connect power supply to cable as required.The cash register could also supply power to terminal.3) Power over Ethernet (PoE) Power is available over the red LAN1 port when the optional PoE and Ethernet hub communication module is installed.• A second Et hernet port• Power over Ethernet• An Et hernet hub• Wi-Fi and Bluetooth LE• Wi-Fi and Cellular GS MThe commu nication module is located on the underside of the termi nal.CommunicationmoduleA communication module must be installed before power can be applied to the terminal. Once the new communication module is properly installed, operate the terminal as usual. WARNING:Working Environment: Temperature -10°C～50°C (14°F～122°F) R.H.: 10%～93% (non-condensing)Storage Environment: Temperature -20°C～60°C (-4°F～140°F) R.H.: 5%～95% (non-condensing) PlugsPlugs61) Stylus Holder PlugIf required, to prevent stylus pen from being inserted vertically into stylus holder, firmly insert plug into openingin holder, aligning with curve of stylus holder.2) Smart Card Reader PlugIf required, insert smart card reader plug into smart card receptacle slot. To remove, if required, gently pry out the plug using a small screwdriver in the slit along top of plug.3) Ethernet PlugAn Ethernet plug is included in case you want to block an inactive LAN port. Align plug so that it matches the shape of the port and gently push into opening. To remove, if required, gently pry off using a small screwdriver in the slit along the top of the plug.Note: LAN2 port is enabled only when Ethernet hub or PoE and Ethernet hub communication module is installed.1) StylusHolderPlug2) Smart Card Reader Plug3) EthernetPlug1) Mounting Locations2) Stylus Po rt 3) RetentionClips1) Align stylus holder over metal screw openings at left side or top of terminal. Insert tabs into indentations along edge. Attach with captive screws.2) Insert connector end of stylus pen into stylus port on left side of terminal.3) Use enclosed plastic card to press stylus cord into retention clips on left side of terminal.Privacy ShieldPrivacy Shield5Insert tabs and snap shield firmly in place to left and right of keypad. Not designed to be removable. Removing the shield breaks the retention tabs and the ability to remotely track the status of the shield is lost.1Privacy ShieldDecorative PlugDecorative Plug – If a privacy shield is not installed, a non-removable decorative plug may be installed in its place. This plug does not provide any PIN entry privacy. CAUTION: If the privacy shield is not installed, you must use PCI-approved alternative methods to secure the PIN pad. Stylus Holder and PenStylus Holder and Pen4

Navigation menu