Panasonic of North America 96NKX-TDA1052 2.4GHz CELL STATION User Manual 100 TDE IM 07 02

Download:
Mirror Download [FCC.gov]
Document ID	799956
Application ID	0jMyFvXoZBXKmWID9oduxA==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	316.23kB (3952859 bits)
Date Submitted	2007-06-04 00:00:00
Date Available	2007-06-05 00:00:00
Creation Date	2007-02-22 17:01:54
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2007-05-31 11:36:46
Document Title	100_TDE_IM_07-02.book
Document Creator	FrameMaker 7.0
Document Author:	kiyota

Pure IP-PBX
Installation Manual
Model
KX-TDE100
KX-TDE200
Thank you for purchasing a Panasonic Pure IP-PBX.
Please read this manual carefully before using this product and save this manual for future use.
KX-TDE100/KX-TDE200: PMMPR Software File Version 1.0000 or later
SD Logo is
a trademark.
Document Version: 2007-02
System Components
System Components Table
Category
Shelves
Model No.
KX-TDE100
Basic Shelf
KX-TDE200
Basic Shelf
Main Processing Card
IPCMPR Option Cards
Description
IP Convergence Main Processing Card (IPCMPR)
KX-TDE0110
16-Channel VoIP DSP Card (DSP16)
KX-TDE0111
64-Channel VoIP DSP Card (DSP64)
KX-TDA0196
Remote Card (RMT)
KX-NCS4104
4-Channel IP Trunk Activation Key (SHGW4)
KX-NCS4208
8-Channel IP Softphone/IP Proprietary Telephone Activation
Key (IPPTS8)
KX-NCS4508
8-Channel IP Proprietary Telephone Activation Key (IPPT8)
KX-NCS4716
16-Channel SIP Extension Activation Key (SPE16)
KX-NCS4910
Activation Key for Software Upgrade to Enhanced Version
(UCAV2)
Virtual CO Line Card
Virtual 16-Channel VoIP Gateway Card (V-IPGW16)
Virtual Extension Cards
Virtual 32-Channel VoIP Extension Card (V-IPEXT32)
Virtual 32-Channel SIP Extension Card (V-SIPEXT32)
KX-TDA0180
8-Port Analog Trunk Card (LCOT8)
KX-TDA0181
16-Port Analog Trunk Card (LCOT16)
KX-TDA0187
T-1 Trunk Card (T1)
KX-TDA0193
8-Port Caller ID Card (CID8)
KX-TDA0290
PRI Card (PRI23)
KX-TDA0484
4-Channel VoIP Gateway Card (IP-GW4E)
KX-TDA0490
16-Channel VoIP Gateway Card (IP-GW16)
Activation Key Cards
Physical CO Line Cards
Installation Manual
System Components Table
Category
Model No.
Description
Physical Extension Cards KX-TDA0143
4 Cell Station Interface Card (CSIF4)
KX-TDA0144
8 Cell Station Interface Card (CSIF8)
KX-TDA0170
8-Port Digital Hybrid Extension Card (DHLC8)
KX-TDA0171
8-Port Digital Extension Card (DLC8)
KX-TDA0172
16-Port Digital Extension Card (DLC16)
KX-TDA0173
8-Port Single Line Telephone Extension Card (SLC8)
KX-TDA0174
16-Port Single Line Telephone Extension Card (SLC16)
KX-TDA0175
16-Port Single Line Telephone Extension with Message
Lamp Card (MSLC16)
KX-TDA0470
16-Channel VoIP Extension Card (IP-EXT16)
KX-TDA0161
4-Port Doorphone Card (DPH4)
KX-TDA0164
4-Port External Input/Output Card (EIO4)
KX-TDA0166
16-Channel Echo Canceller Card (ECHO16)
KX-TDA0168
Extension Caller ID Card (EXT-CID)
KX-TDA0190
Optional 3-Slot Base Card (OPB3)
KX-TDA0191
4-Channel Message Card (MSG4)
KX-TDA0103
L-Type Power Supply Unit (PSU-L)
KX-TDA0104
M-Type Power Supply Unit (PSU-M)
KX-TDA0108
S-Type Power Supply Unit (PSU-S)
KX-T0141
2-Channel Cell Station Unit Using a DHLC/DLC Card (PTinterface CS) for 2.4 GHz Portable Station
KX-TDA0142
3-Channel Cell Station Unit Using a CSIF Card for 2.4 GHz
Portable Station
KX-T0151
2-Channel Cell Station Unit Using a DHLC/DLC Card (PTinterface CS) for 2.4 GHz Portable Station
KX-TDA0152
3/4-Channel Cell Station Unit Using a CSIF Card for 2.4 GHz
Portable Station
KX-TDA0158
5-Channel High-density Cell Station Unit Using a DHLC/DLC
Card (PT-interface CS) for 2.4 GHz Portable Station
KX-A258
Blank Slot Cover
KX-T30865
Doorphone
Other Physical Cards
Power Supply Units
(PSUs)
Cell
Stations
(CSs)
Basic CSs
High-density
CSs
Proprietary Equipment
Installation Manual
Compatible Panasonic Proprietary Telephones
The PBX supports the following telephones:
•
IP proprietary telephones (e.g., KX-NT300 series)
•
IP softphones (e.g., KX-NCS8100)
•
Digital proprietary telephones (e.g., KX-T7600 series)
•
Analog proprietary telephones (e.g., KX-T7700 series)
•
Portable stations (e.g., KX-TD7690)
•
DSS consoles (e.g., KX-T7640)
Note
KX-NT300 series IP-PTs are supported by the IPCMPR card, but not by the IP-EXT16 card. In contrast,
KX-NT136 and KX-NT265 IP-PTs are supported by the IP-EXT16 card, but not by the IPCMPR card.
Only the KX-NT265 (D) IP-PT is supported by both cards.
Incompatible Panasonic Proprietary Telephones
The PBX does not support the following telephones:
•
KX-T30800 series proprietary telephones and DSS consoles
•
KX-T61600 series proprietary telephones and DSS consoles
•
KX-T123200 series proprietary telephones and DSS consoles
Notes
•
•
For the equipment (e.g., Add-on Key Module, USB Module, Headset*1) that can be connected to a
particular telephone, refer to the telephone's manual.
For other equipment that can be connected to the PBX, refer to "1.2.2 System Connection
Diagram".
List of Abbreviations
•
•
•
•
•
•
•
APT → Analog Proprietary Telephone
DPT → Digital Proprietary Telephone
IP-PT → IP Proprietary Telephone
PS → Portable Station
PT → Proprietary Telephone
SIP Extension → Session Initiation Protocol Extension (SIP hardphones/SIP softphones)
SLT → Single Line Telephone
Notice
This PBX supports SIP Extensions. However, some PBX features may not be available for SIP
Extensions, depending on your telephone type.
*1
The KX-T7090 headset can be connected to the KX-T7000, KX-T7200, KX-T7300, and KX-T7400 series telephones.
Installation Manual
Important Notice
Prior to connection of this product, please verify that the intended operating environment is supported.
Satisfactory performance cannot be guaranteed for the following:
– interoperability and compatibility with all devices and systems connected to this product
– proper operation and compatibility with services provided by telecommunications companies over
connected networks
Installation Manual
Important Safety Instructions
SAFETY REQUIREMENTS
When using your telephone equipment, basic safety precautions should always be followed to reduce the
risk of fire, electric shock and injury to persons, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Clean with a damp cloth.
4. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry
tub, in a wet basement, or near a swimming pool.
5. Do not place the product on an unstable surface, as a fall may cause serious internal damage.
6. Slots and openings in the front, back and bottom of the cabinet are provided for ventilation; to protect
it from overheating, these openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface while in use. The product
should never be placed near or over a radiator or other heat source. This product should not be placed
in a sealed environment unless proper ventilation is provided.
7. The product should only be connected to the type of electrical power supply specified on the product
label. If you are not sure of the type of power supply to your home, consult your dealer or local power
company.
8. For safety purposes this unit is equipped with a grounded plug. If you do not have a grounded outlet,
please have one installed. Do not bypass this safety feature by tampering with the plug.
9. Do not allow anything to rest on the power cord. Do not locate this product where the power cord may
be stepped on or tripped on.
10. To reduce the risk of fire or electric shock, do not overload wall outlets and extension cords.
11. Do not insert objects of any kind into this product through its slots and openings, as they may touch
dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill
liquid of any kind on or in the product.
12. To reduce the risk of electric shock, do not disassemble this product. Only qualified personnel should
service this product. Opening or removing covers may expose you to dangerous voltages or other risks.
Incorrect reassembly can cause electric shock.
13. Unplug this product from the wall outlet and have it serviced by qualified service personnel in the
following cases:
a)
b)
c)
d)
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate according to the operating instructions. Adjust only the controls that
are explained in the operating instructions. Improper adjustment of other controls may result in
damage and may require service by a qualified technician to restore the product to normal
operation.
e) If the product has been dropped or the cabinet has been damaged.
f) If product performance deteriorates.
14. Avoid using wired telephones during an electrical storm. There is a remote risk of electric shock from
lightning.
15. Do not use a telephone in the vicinity of a gas leak to report the leak.
Installation Manual
SAVE THESE INSTRUCTIONS
Installation Manual
Precaution
WARNING
DO
NOT
REMOVE
SD
MEMORY
CARD
WHILE
POWER
IS
SUPPLIED TO THE PBX
Doing so may cause the PBX to fail to
start when you try to restart the system.
Installation Manual
•
Keep the unit away from heating appliances and devices that generate electrical noise such as
fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of
the PBX.
•
This unit should be kept free of dust, moisture, high temperature (more than 40 ˚C) and vibration, and
should not be exposed to direct sunlight.
If you are having problems making calls to outside destinations, follow this procedure to test the CO
lines:
•
1. Disconnect the PBX from all CO lines.
2. Connect known working SLTs to those CO lines.
3. Make a call to an external destination using those SLTs.
•
If a call cannot be carried out correctly, there may be a problem with the CO line that the SLT is
connected to. Contact your telephone company.
If all SLTs operate properly, there may be a problem with your PBX. Do not reconnect the PBX to the
CO lines until it has been serviced by an authorized Panasonic Factory Service Center.
Wipe the unit with a soft cloth. Do not clean with abrasive powders or with chemical agents such as
benzene or thinner.
WARNING
•
•
•
•
•
•
•
•
THIS UNIT MAY ONLY BE INSTALLED AND SERVICED BY QUALIFIED SERVICE
PERSONNEL.
IF DAMAGE TO THE UNIT EXPOSES ANY INTERNAL PARTS, DISCONNECT THE
POWER SUPPLY CORD IMMEDIATELY AND RETURN THE UNIT TO YOUR DEALER.
UNPLUG THIS UNIT FROM THE AC OUTLET IF IT EMITS SMOKE, AN ABNORMAL
SMELL OR MAKES UNUSUAL NOISE. THESE CONDITIONS CAN CAUSE FIRE OR
ELECTRIC SHOCK. CONFIRM THAT SMOKE HAS STOPPED AND CONTACT AN
AUTHORIZED PANASONIC FACTORY SERVICE CENTER.
WHEN RELOCATING THE EQUIPMENT, FIRST DISCONNECT THE TELECOM
CONNECTION BEFORE DISCONNECTING THE POWER CONNECTION. WHEN THE
UNIT IS INSTALLED IN THE NEW LOCATION, RECONNECT THE POWER FIRST,
AND THEN RECONNECT THE TELECOM CONNECTION.
TO PREVENT POSSIBLE FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
THE POWER SUPPLY CORD IS USED AS THE MAIN DISCONNECT DEVICE.
ENSURE THAT THE AC OUTLET IS LOCATED NEAR THE EQUIPMENT AND IS
EASILY ACCESSIBLE.
DANGER OF EXPLOSION EXISTS IF A BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE
BATTERY MANUFACTURER. DISPOSE OF USED BATTERIES ACCORDING TO THE
MANUFACTURER'S INSTRUCTIONS.
THE SD MEMORY CARD POSES A CHOKING HAZARD. KEEP THE SD MEMORY
CARD OUT OF REACH OF CHILDREN.
Installation Manual
Password Security
Warning to the Administrator or Installer regarding the system password
1. Please provide all system passwords to the customer.
2. To avoid unauthorized access and possible abuse of the PBX, keep the passwords secret, and
inform the customer of the importance of the passwords, and the possible dangers if they become
known to others.
3. The PBX has default passwords preset. For security, change these passwords the first time that
you program the PBX.
4. Change the passwords periodically.
5. It is strongly recommended that passwords of 10 numbers or characters be used for maximum
protection against unauthorized access. For a list of numbers and characters that can be used in
system passwords, refer to "1.1.2 Entering Characters" in the PC Programming Manual.
6. If a system password is forgotten, it can be found by loading a backup of the system data into a
PC, and checking the password using the KX-TDA Maintenance Console software. If you do not
have a backup of the system data, you must reset the PBX to its factory defaults and reprogram it.
Therefore, we strongly recommend maintaining a backup of the system data. For more information
on how to back up the system data, refer to "2.4.1 Tool—SD memory backup" in the PC
Programming Manual.
However, as system passwords can be extracted from backup copies of the system data file, do
not allow unauthorized access to these files.
Notice for users in California
This product contains a CR coin cell lithium battery that
contains perchlorate material—special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
10
Installation Manual
When you ship the product
Carefully pack and send it prepaid, adequately insured and preferably in the original carton. Attach a
postage-paid letter, detailing the symptom, to the outside of the carton. DO NOT send the product to the
Executive or Regional Sales offices. They are NOT equipped to make repairs.
Product Service
Panasonic Factory Service Centers for this product are listed in the service center directory. Consult your
certified Panasonic dealer for detailed instructions.
For Future Reference
Please print, record, and retain the following information for future reference.
For Future Reference
Please print, record, and retain the following information for future reference.
Note
The serial number of this product can be found on the label affixed to the unit. You should record the
model number and the serial number of this unit as a permanent record of your purchase to aid in
identification in the event of theft.
MODEL NO.
SERIAL NO.
DATE OF PURCHASE
NAME OF DEALER
DEALER'S ADDRESS
DEALER'S TEL. NO.
Installation Manual
11
Introduction
This Installation Manual is designed to serve as an overall technical reference for the Panasonic Pure IPPBX, KX-TDE100/KX-TDE200. It provides instructions for installing the hardware, and programming the
PBX using the KX-TDE Maintenance Console.
The Structure of this Manual
This manual contains the following sections:
Section 1 System Outline
Provides general information on the PBX, including the system capacity and specifications.
Section 2 Activation Key Installation
Describes information on activation keys, including how to obtain an activation key and install it in the
SD Memory Card.
Section 3 Installation
Describes the procedures to install the PBX. Detailed instructions for planning the installation site,
installing the shelves and optional service cards, and cabling of peripheral equipment are provided.
Further information on system expansion and peripheral equipment installation is included.
Section 4 Guide for the KX-TDE Maintenance Console
Explains the installation procedure, structure, and basic information of the KX-TDE Maintenance
Console.
Section 5 Troubleshooting
Provides information on the PBX and telephone troubleshooting.
About the Other Manuals
Along with this Installation Manual, the following manuals are available:
Feature Manual
Describes all basic, optional and programmable features of the PBX.
PC Programming Manual
Provides step-by-step instructions for performing system programming using a PC.
PT Programming Manual
Provides step-by-step instructions for performing system programming using a PT.
Operating Manual
Provides operating instructions for end users using a PT, SLT, PS, or DSS Console.
About the software version of your PBX
The contents of this manual apply to PBXs with a certain software version, as indicated on the cover of this
manual. To confirm the software version of your PBX, see "How do I confirm the software version of the PBX
or installed cards?" in the FAQ of the PC Programming Manual, or "[190] Main Processing (MPR) Software
Version Reference" in the PT Programming Manual.
Trademarks
•
•
•
12
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such
marks by Matsushita Electric Industrial Co., Ltd. is under licence.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
Intel and Celeron are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the United States and other countries.
Installation Manual
•
•
All other trademarks identified herein are the property of their respective owners.
Screen shots reprinted with permission from Microsoft Corporation.
Installation Manual
13
F.C.C. REQUIREMENTS AND RELEVANT
INFORMATION
1. Notification to the Telephone Company
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On
the side of this equipment is a label that contains, among other information, a product identifier in the
following format:
•
US:AAAEQ##TXXXX
If requested, this number must be provided to the telephone company.
Installation must be performed by a qualified professional installer. If required, provide the telephone
company with the following technical information:
•
Telephone numbers to which the system will be connected
•
Make: Panasonic
•
Model: KX-TDE100 and KX-TDE200
•
Certification No.: found on the side of the unit
•
Ringer Equivalence No.: 0.3A
•
Facility Interface Code: 02LS2, 04DU9.BN/DN/1KN/1SN, METALLIC
•
Service Order Code: 9.0F, 6.0P
•
Required Network Interface Jack: RJ21X, RJ48C, RJ2HX
2. Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number
of devices that may be connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part of the product
identifier that has the following format:
•
US:AAAEQ##TXXXX
The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier
products, the REN is separately shown on the label.
3. Incidence of Harm to the Telephone Lines
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn't practical,
the telephone company will notify the customer as soon as possible. Also, you will be advised of your
right to file a complaint with the FCC if you believe it is necessary.
4. Changes in Telephone Company Communications Facilities, Equipment, Operations and
Procedures
The telephone company may make changes in its facilities, equipment, operations or procedures that
could affect the operation of the equipment. If this happens the telephone company will provide
advance notice in order for you to make necessary modifications to maintain uninterrupted service.
5. Trouble with this equipment
If trouble is experienced with this equipment, for repair or warranty information, please see the attached
warranty, which includes the Servicenter Directory. If the equipment is causing harm to the telephone
network, the telephone company may request that you disconnect the equipment until the problem is
resolved.
6. Connection to Party Line
Connection to party line service is subject to state tariffs. Contact the state public utility commission,
public service commission or corporation commission for information.
14
Installation Manual
7. Combined Use with Alarm Equipment
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment does not disable your alarm equipment. If you have questions about what
will disable alarm equipment, consult your telephone company or a qualified installer.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this device.
When programming emergency numbers and/or making test calls to emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the call before hanging up.
2. Perform such activities in the off-peak hours, such as early morning hours or late evenings.
WARNING
The software contained in the ARS and TRS features to allow user access to the
network must be upgraded to recognize newly established network area codes and
exchange codes as they are placed into service. Failure to upgrade the on-premise
PBXs or peripheral equipment to recognize the new codes as they are established will
restrict the customer and users of the PBX from gaining access to the network and to
these codes.
KEEP THE SOFTWARE UP-TO-DATE WITH THE LATEST DATA.
Installation Manual
15
For Cell Station
CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could
void user's authority to operate this device.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Some wireless telephones operate at frequencies that may cause interference to nearby TVs and
VCRs. To minimize or prevent such interference, the base of the wireless telephone should not be
placed near or on top of a TV or VCR. If interference is experienced, move the wireless telephone
further away from the TV or VCR. This will often reduce, or eliminate, interference.
Operating near 2.4 GHz electrical appliances may cause interference. Move away from the electrical
appliances.
CAUTION
To comply with FCC RF exposure requirements in uncontrolled environment:
•
This equipment must be installed and operated in accordance with provided instructions and a
minimum 20 cm (8 in) spacing must be provided between antenna and all person's body (excluding
extremities of hands, wrist and feet) during wireless modes of operation.
•
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
Medical—consult the manufacturer of any personal medical devices, such as pacemakers, to
determine if they are adequately shielded from external RF (radio frequency) energy. (The unit operates
in the frequency range of 2401 MHz to 2480 MHz, and the power output level can range from 0.004 W
to 0.4 W.) Do not use the unit in health care facilities if any regulations posted in the area instruct you
not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to
external RF (radio frequency) energy.
16
Installation Manual
Table of Contents
System Outline ..................................................................................... 21
1.1
1.1.1
1.2
1.2.1
1.2.2
1.3
1.3.1
1.4
1.4.1
1.4.2
1.4.3
Activation Key Installation................................................................... 41
2.1
2.1.1
2.1.2
2.1.3
System Highlights .......................................................................................................... 22
System Highlights ............................................................................................................. 22
Basic System Construction ........................................................................................... 26
Basic Shelf ........................................................................................................................ 26
System Connection Diagram ............................................................................................ 27
Optional Equipment........................................................................................................ 29
Optional Equipment .......................................................................................................... 29
Specifications ................................................................................................................. 31
General Description .......................................................................................................... 31
Characteristics .................................................................................................................. 33
System Capacity ............................................................................................................... 34
Information about the Activation Keys ......................................................................... 42
Activation Keys.................................................................................................................. 42
Activation Key Card and Key Management System.......................................................... 44
Activation Key File............................................................................................................. 45
Installation............................................................................................. 47
3.1
3.1.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.2.6
3.2.7
3.2.8
3.2.9
3.2.10
3.2.11
3.2.12
3.2.13
3.3
3.3.1
3.3.2
3.3.3
3.4
3.4.1
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
Before Installation........................................................................................................... 48
Before Installation ............................................................................................................. 48
Installation of the PBX.................................................................................................... 50
Unpacking ......................................................................................................................... 50
Names and Locations ....................................................................................................... 51
Opening/Closing the Front Cover...................................................................................... 52
Installing/Replacing the Power Supply Unit ...................................................................... 54
Frame ground Connection ................................................................................................ 58
Installing/Removing the Optional Service Cards .............................................................. 59
Types of Connectors ......................................................................................................... 64
Attaching a Ferrite Core.................................................................................................... 66
Fastening an Amphenol Connector .................................................................................. 68
Wall Mounting (KX-TDE200)............................................................................................. 70
Wall Mounting (KX-TDE100)............................................................................................. 72
Floor Standing (KX-TDE200 Only).................................................................................... 74
Surge Protector Installation .............................................................................................. 76
Information about the Main Processing Card .............................................................. 79
IPCMPR Card ................................................................................................................... 79
DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111) ........................................ 82
RMT Card (KX-TDA0196)................................................................................................. 83
Information about the Virtual Cards.............................................................................. 84
Virtual Cards ..................................................................................................................... 84
Information about the Physical Trunk Cards................................................................ 85
LCOT8 Card (KX-TDA0180) and LCOT16 Card (KX-TDA0181)....................................... 85
CID8 Card (KX-TDA0193) ................................................................................................ 87
T1 Card (KX-TDA0187) .................................................................................................... 88
PRI23 Card (KX-TDA0290)............................................................................................... 90
IP-GW4E Card (KX-TDA0484) ......................................................................................... 92
Installation Manual
17
3.5.6
3.6
3.6.1
3.6.2
3.6.3
3.6.4
3.6.5
3.6.6
3.6.7
3.6.8
3.7
3.7.1
3.7.2
3.7.3
3.7.4
3.7.5
3.8
3.8.1
3.8.2
3.8.3
3.8.4
3.9
3.9.1
3.9.2
3.9.3
3.9.4
3.9.5
3.9.6
3.9.7
3.9.8
3.10
3.10.1
3.11
3.11.1
3.12
3.12.1
3.13
3.13.1
3.14
3.14.1
Guide for the KX-TDE Maintenance Console ................................... 171
4.1
4.1.1
4.2
4.2.1
4.3
4.3.1
5.1
18
IP-GW16 Card (KX-TDA0490) ..........................................................................................94
Information about the Physical Extension Cards ........................................................96
CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) ...........................................96
DHLC8 Card (KX-TDA0170) .............................................................................................99
DLC8 Card (KX-TDA0171).............................................................................................. 102
DLC16 Card (KX-TDA0172)............................................................................................ 104
SLC8 Card (KX-TDA0173).............................................................................................. 106
EXT-CID Card (KX-TDA0168) .........................................................................................108
SLC16 Card (KX-TDA0174) and MSLC16 Card (KX-TDA0175)..................................... 109
IP-EXT16 Card (KX-TDA0470) ....................................................................................... 111
Information about the Other Physical Cards .............................................................. 113
OPB3 Card (KX-TDA0190) ............................................................................................. 113
DPH4 Card (KX-TDA0161) ............................................................................................. 114
EIO4 Card (KX-TDA0164)............................................................................................... 116
ECHO16 Card (KX-TDA0166) ........................................................................................ 119
MSG4 Card (KX-TDA0191)............................................................................................. 120
Connection of Extensions............................................................................................ 121
Maximum Cabling Distances of the Extension Wiring (Twisted Cable) ...........................121
Parallel Connection of the Extensions ............................................................................ 123
Digital EXtra Device Port (Digital XDP) Connection........................................................126
First Party Call Control CTI Connection .......................................................................... 128
Connection of 2.4 GHz Portable Stations ...................................................................129
Overview ......................................................................................................................... 129
Procedure Overview........................................................................................................ 131
Site Planning ................................................................................................................... 133
Before Site Survey .......................................................................................................... 137
Site Survey...................................................................................................................... 141
After Site Survey .............................................................................................................145
Connecting a Cell Station to the PBX ............................................................................. 146
Wall Mounting ................................................................................................................. 155
Connection of Doorphones, Door Openers, External Sensors, and External Relays........... 159
Connection of Doorphones, Door Openers, External Sensors, and External Relays............ 159
Connection of Peripherals ........................................................................................... 162
Connection of Peripherals ............................................................................................... 162
LAN Connection ............................................................................................................ 166
LAN Connection .............................................................................................................. 166
Power Failure Connections .......................................................................................... 167
Power Failure Connections ............................................................................................. 167
Starting the PBX............................................................................................................ 169
Starting the PBX .............................................................................................................169
Overview ........................................................................................................................172
Overview ......................................................................................................................... 172
Connection .................................................................................................................... 173
Connection ...................................................................................................................... 173
Installation of the KX-TDE Maintenance Console ...................................................... 175
Installing and Starting the KX-TDE Maintenance Console ............................................. 175
Troubleshooting.................................................................................. 179
Troubleshooting ............................................................................................................ 180
Installation Manual
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
Installation....................................................................................................................... 180
Connection...................................................................................................................... 183
Operation ........................................................................................................................ 185
Using the Reset Button ................................................................................................... 187
Troubleshooting by Error Log .......................................................................................... 188
Index .......................................................................................................... 191
Installation Manual
19
20
Installation Manual
Section
System Outline
This section provides general information on the PBX,
including the system capacity and specifications.
Installation Manual
21
1.1 System Highlights
1.1
System Highlights
1.1.1
System Highlights
IPCMPR Card Features
The IPCMPR card (the pre-installed Main Processing card) includes the following features and resources:
VoIP CO Lines/VoIP Extensions
The IPCMPR card allows the use of IP CO lines (H.323) and IP telephones (IP-PTs, IP softphones, and
SIP Extensions). By connecting a DSP card to the IPCMPR card, these IP CO lines and extensions can
be used. It is also possible to increase the number of IP CO lines (max. 32) and extensions (max. 128)
through the purchase of activation key cards.
LAN Connection
The IPCMPR card comes included with a Local Area Network (LAN) port (RJ45 port) allowing for the
PBX to be connected to a LAN.
Computer Telephony Integration (CTI) Features
Connecting a PC to a DPT, or connecting a CTI Server to this PBX, allows functions of the PC, PBX
and extensions to be integrated. For example, detailed caller information can be taken from a database
and displayed on the PC as a call arrives, or the PC can dial numbers for the extension automatically.
Simplified Voice Message (SVM) Features
The IPCMPR card comes pre-installed with the SVM feature (2 channels), allowing for simple
answering machine services to be supported.
Internet Protocol (IP) Telephone Features
This PBX supports the following telephone features that use IP:
IP-PT Features
This PBX supports the connection of IP-PTs which function almost identically to normal PTs. However,
they connect to the PBX over a LAN and make and receive calls using IP. In addition, KX-NT300 series
IP-PTs support the following features:
– Self Labelling (KX-NT366 only)
The LCDs featured next to the 12 flexible buttons of the KX-NT366 can be programmed to display
information regarding the setting of the corresponding flexible button. In addition, the flexible
buttons can be organized into 4 “pages” allowing you to assign a total of 4 items to each physical
button.
– Optional Modules
•
–
22
KX-NT307(PSLP1528) Bluetooth ® Module:
Allows for a Bluetooth wireless headset to be connected to a KX-NT300 series IP-PT.
•
KX-NT303 Add-on 12 Key Module:
Allows for 12 additional flexible buttons to be connected to a KX-NT346 or KX-NT343.
•
KX-NT305 Add-on 60 Key Module:
Allows for 60 additional flexible buttons to be connected to a KX-NT346 or KX-NT343.
High Sound Quality
Installation Manual
1.1 System Highlights
Calls between KX-NT300 series IP-PTs support G.722 CODEC allowing for high sound quality
conversations.
SIP (Session Initiation Protocol) Extensions
This PBX supports the connection of third party SIP supported IP telephones (hardphones and
softphones). SIP Extensions make and receive calls using IP.
IP Softphones
This PBX supports the connection of Panasonic IP softphones, providing IP-PT operations and features
using software on a PC.
Internet Protocol (IP) Related Features
Server Connection
This PBX supports the connection to the following servers, allowing for enhanced efficiency and record
keeping:
– SNMP Server:
Allows for users assigned as SNMP managers to manage and receive PBX system status
information, such as local alarm information and general system activity using Simple Network
Management Protocol (SNMP).
– SNTP Server:
Allows for the PBX to automatically receive and update the time setting using Simple Network Time
Protocol (SNTP).
– DHCP Server:
Allows for this PBX to receive IP addresses from a Dynamic Host Configuration Protocol (DHCP)
server.
Peer-to-peer Connection
Intercom calls can be made between peer-to-peer compatible IP extensions allowing for
communication without using the PBX's VoIP resources.
Networking Features
This PBX supports the following networking features:
Voice over Internet Protocol (VoIP) Network
The PBX can connect to another PBX via a private IP network. In this case, voice signals are converted
into IP packets and sent through this network. Automatic rerouting of VoIP calls to public CO lines is
also available, in case of network difficulties.
TIE Line Service
A TIE line is a privately leased communication line between two or more PBXs, which provides cost
effective communications between company members at different locations.
Virtual Private Network (VPN)
VPN is a service provided by the VPN service provider. It uses an existing public line as if it were a
private line.
QSIG Network
QSIG is a protocol based on ISDN (Q.931) and offers enhanced PBX features in a private network of
two or more connected PBXs.
Installation Manual
23
1.1 System Highlights
External Device Support
The following are just a few of the many useful optional devices available to enhance your telephony system:
Portable Station (PS) Features
PSs can be connected to this PBX. It is possible to use the PBX features using the PS like a PT. This
PBX supports basic CSs (allows up to 4 PSs to be on a call simultaneously) as well as high-density
CSs (allows up to 8 PSs to be on a call simultaneously). A PS can also be used in parallel with a wired
telephone (Wireless XDP Parallel Mode). In this case, the wired telephone is the main telephone and
the PS is the sub telephone.
Cellular Phone Features (KX-NCS4910 required)
This PBX supports the use of cellular phones destinations with the PBX. In combination with the use
of certain features such as Virtual PS, DISA, and XDP Parallel mode, cellular phones can make and
receive calls as if they were registered extensions.
Phone Assistant (PA) Pro Series
This PBX supports KX-TDA Phone Assistant Pro Series applications, a collection of highly-intuitive CTI
applications that allow you to use your PC to access a variety of PBX features conveniently and
efficiently. PA Pro series applications combine the efficiency and user-friendliness of CTI applications
with the convenience of server-based applications, allowing User IDs, passwords and PBX settings to
be configured over a web browser.
Voice Mail Features
This PBX supports Voice Processing Systems (VPS) with DTMF Integration as well as DPT (Digital)
Integration, connected locally and over a network.
ACD Report Server (KX-NCV200)
This PBX supports VPSs with an ACD Report Server. In addition to VPS features, the ACD Report
Server provides you with a variety of features, such as monitoring, reporting, call logging features and
creating performance graphs, to manage call information efficiently.
Other Useful Features
Easy Installation and Setup
–
–
With Physical Cards
By simply connecting telephones and outside lines to analog extension and CO line cards you can
make and receive calls. For digital CO lines (e.g., T1, etc.), it may be necessary to first make the
required settings and restart the PBX.
With Virtual Cards
By connecting the PBX to the LAN, installing each virtual card and registering the IP telephones
through system programming, you can make and receive calls.
Enhanced Walking Extension Feature
It is possible to use the Walking Extension feature with extensions in Service-in (functions normally)
and Service-out (cannot make CO line calls or receive calls) modes, allowing users to use their
extensions at home and at work, or for multiple users who work in shifts to use their own extension
settings on a single telephone.
24
Installation Manual
1.1 System Highlights
Built-in Small Call Centre Features
An incoming call distribution (ICD) group can be used as a small call centre with the following features:
– Queuing Feature
When a preprogrammed number of extensions in an ICD group are busy, additional incoming calls
can wait in a queue. While callers are waiting in the queue, they can be sent an outgoing message
(OGM) informing the caller of the current situation, or be redirected to another destination or
disconnected depending on the amount of time the caller has been waiting.
– Log-in/Log-out
ICD group members can join (Log-in) or leave (Log-out) their groups manually. After a call is
completed, a preprogrammed time period where users will not receive calls can be assigned
(Wrap-up). This gives time for users to make reports about the previous call without be interrupted
or allows users to not receive calls while they are taking a break.
– VIP Call
The VIP Call feature is one method of making sure that calls from preferred customers or callers
are answered quickly. When using VIP Call mode, ICD groups are assigned a priority, allowing calls
in higher-priority groups to be answered before calls in lower-priority groups.
Hospitality Features
This PBX has several features allowing it to be used effectively and efficiently in a hotel-type
environment. These features allow extensions assigned as hotel operators to change and monitor the
room status of guest rooms, check or set wake-up calls, and print out records of guest charges.
Installation Manual
25
1.2 Basic System Construction
1.2
Basic System Construction
1.2.1
Basic Shelf
The basic shelf contains an IPCMPR card for controlling the PBX. To use the system, install a power supply
unit (PSU) in the PSU Slot and optional service cards in the basic shelf.
KX-TDE100
KX-TDE200
Construction of the Basic Shelf
IPCMPR Card
Free Slots
PSU Slot
KX-TDE100
26
Installation Manual
IPCMPR Card
Free Slots
PSU Slot
KX-TDE200
1.2 Basic System Construction
1.2.2
System Connection Diagram
Private
IP Network
CO (Telephone Company) Lines
Analog/PRI/T1
Remote PC
Router
Pure IP-PBX
PC
Batteries
IP-PT
IP Softphone
Fax Machine
SLT
PC
SIP Extension
Printer
Wireless Phone
APT
DSS Console
CTI Server
ISDN Telephone
External Sensor/
External Relay Device
Doorphone & Door Opener
DPT
PS
DSS Console
USB
CS
KX-T7636/
KX-T7633
PC
PC
BGM/Music On Hold (MOH)
PC
Voice Processing
System
Pager/ Amplifier
Speaker
KX-T7600 DPT
KX-T7600 DPT
Installation Manual
27
1.2 Basic System Construction
LCOT4
LCOT16
(KX-TDA0183)
(KX-TDA0181)
LCOT8
(KX-TDA0180)
CID8
(KX-TDA0193)
Analog
CO Line
Telephone
Company
ISDN PRI Line
(Digital CO Line)
T1 Line
(Digital CO Line)
MSLC16
(KX-TDA0175)
SLC16
(KX-TDA0174)
SLT
Wireless Phone
Fax Machine
SLC8
(KX-TDA0173)
EXT-CID
(KX-TDA0168)
KX-T7636/
KX-T7633
PRI23
(KX-TDA0290)
KX-T7600
DPT
PC
KX-T7600
DPT
DLC16
(KX-TDA0172)
Voice
Processing
System
DLC8
(KX-TDA0171)
T1
(KX-TDA0187)
DHLC8
(KX-TDA0170)
OPB3
(KX-TDA0190)
DPT
DSS Console
APT
DPT
SLT Wireless Phone
DPH4
(KX-TDA0161)
EIO4
(KX-TDA0164)
PT-interface CS PS
(Basic/High-density)
DSS Console
Fax Machine
PT-interface CS PS
Voice
(Basic/High-density)
Processing
System
KX-T7636/
KX-T7633
PC
KX-T7600 KX-T7600
DPT
DPT
Doorphone & Door Opener
ECHO16
(KX-TDA0166)
IP-GW4E
(KX-TDA0484)
Private IP
Network
Router
Uninterruptible
Power Supply (UPS)
MSG4
(KX-TDA0191)
IP-GW16
(KX-TDA0490)
PSU-S/M/L
(KX-TDA0108/
KX-TDA0104/
KX-TDA0103)
CSIF4
(KX-TDA0143)
CSIF8
(KX-TDA0144)
IP-EXT16
(KX-TDA0470)
Station Message
Detail Recording (SMDR)
External Sensor/External Relay Device
CS
PS
LAN
IPCMPR
(Installed by default)
RMT
(KX-TDA0196)
IP-PT
IP Softphone
Radio
DSP16
(KX-TDE0110)
Amplifier
DSP64
(KX-TDE0111)
Pager/Speaker
PC
Private IP
Network
Router
Virtual Trunk
Slot
Virtual
Extension Slot
V-IPGW16
V-IPEXT32
V-SIPEXT32
LAN
IP-PT
Mountable Equipment
28
Installation Manual
IP Softphone SIP Extension
PC
CTI Server
1.3 Optional Equipment
1.3
Optional Equipment
1.3.1
Optional Equipment
Model No.
Model Name
Description
KX-TDE0110
16-Channel VoIP DSP Card (DSP16) 16-channel digital signal processor card with an
SHGW4 activation key and an IPPT8 activation key
pre-installed. Compliant with ITU-T G.729a and
G.711 CODEC methods. To be mounted on the
IPCMPR card.
KX-TDE0111
64-Channel VoIP DSP Card (DSP64) 64-channel digital signal processor card with four
SHGW4 activation keys and four IPPT8 activation
keys pre-installed. Compliant with ITU-T G.729a
and G.711 CODEC methods. To be mounted on the
IPCMPR card.
KX-TDA0103
L-Type Power Supply Unit (PSU-L)
Power Supply Unit for the KX-TDE200. Total power
output of 279 W. Safety Class 1 compliant.
KX-TDA0104
M-Type Power Supply Unit (PSU-M)
Power Supply Unit for the KX-TDE100 and KXTDE200. Total power output of 140.4 W. Safety
Class 1 compliant.
KX-TDA0108
S-Type Power Supply Unit (PSU-S)
Power Supply Unit for the KX-TDE100. Total power
output of 74 W. Safety Class 1 compliant.
KX-TDA0143
4 Cell Station Interface Card (CSIF4) 4-port CS interface card for 4 CSs.
KX-TDA0144
8 Cell Station Interface Card (CSIF8) 8-port CS interface card for 8 CSs.
KX-TDA0161
4-Port Doorphone Card (DPH4)
4-port doorphone card for 4 doorphones and 4 door
openers. To be mounted on the OPB3 card.
KX-TDA0164
4-Port External Input/Output Card
(EIO4)
4-port external input/output card. To be mounted on
the OPB3 card.
KX-TDA0166
16-Channel Echo Canceller Card
(ECHO16)
16-channel card for echo cancellation during
conferences. To be mounted on the OPB3 card.
KX-TDA0168
Extension Caller ID Card (EXT-CID)
Sends Caller ID signals to extension ports. To be
mounted on the SLC8 card only.
KX-TDA0170
8-Port Digital Hybrid Extension Card 8-port digital hybrid extension card for DPTs, APTs,
(DHLC8)
SLTs, DSS consoles, and PT-interface CSs (Basic/
High-density), with 2 power failure transfer (PFT)
ports.
KX-TDA0171
8-Port Digital Extension Card (DLC8) 8-port digital extension card for DPTs, DSS
consoles, and PT-interface CSs (Basic/Highdensity).
KX-TDA0172
16-Port Digital Extension Card
(DLC16)
16-port digital extension card for DPTs, DSS
consoles, and PT-interface CSs (Basic/Highdensity).
Installation Manual
29
1.3 Optional Equipment
Model No.
Model Name
Description
KX-TDA0173
8-Port Single Line Telephone
Extension Card (SLC8)
8-port extension card for SLTs with 2 power failure
transfer (PFT) ports.
KX-TDA0174
16-Port Single Line Telephone
Extension Card (SLC16)
16-port extension card for SLTs with 4 power failure
transfer (PFT) ports.
KX-TDA0175
16-Port Single Line Telephone
Extension with Message Lamp Card
(MSLC16)
16-port extension card for SLTs with Message
Waiting Lamp control and 4 power failure transfer
(PFT) ports. Maximum power output of 160 V/90 V
for Message Waiting Lamp control.
KX-TDA0180
8-Port Analog Trunk Card (LCOT8)
8-port analog CO line card with 2 power failure
transfer (PFT) ports.
KX-TDA0181
16-Port Analog Trunk Card (LCOT16) 16-port analog CO line card with 4 power failure
transfer (PFT) ports.
KX-TDA0187
T-1 Trunk Card (T1)
1-port T1 CO line card. EIA/TIA standard compliant.
KX-TDA0190
Optional 3-Slot Base Card (OPB3)
Optional 3-slot base card for mounting a maximum
of 3 option cards from the following: MSG4, DPH4,
or ECHO16 card.
KX-TDA0191
4-Channel Message Card (MSG4)
4-channel message card. To be mounted on the
OPB3 card.
KX-TDA0193
8-Port Caller ID Card (CID8)
8-port Caller ID signal type FSK/FSK (with Call
Waiting Caller ID [Visual Caller ID])/DTMF. To be
mounted on the LCOT8/LCOT16 cards.
KX-TDA0196
Remote Card (RMT)
Analog modem card for remote communication with
the PBX. ITU-T V.90 support. To be mounted on the
IPCMPR card.
KX-TDA0290
PRI Card (PRI23)
1-port ISDN Primary Rate Interface card (23B
channels). NI (North American standard ISDN
protocol) compliant.
KX-TDA0470
16-Channel VoIP Extension Card (IP- 16-channel VoIP extension card. Compliant with
EXT16)
Panasonic proprietary protocol, and ITU-T G.729a
and G.711 CODEC methods.
KX-TDA0484
4-Channel VoIP Gateway Card (IPGW4E)
KX-TDA0490
16-Channel VoIP Gateway Card (IP- 16-channel VoIP gateway card. Compliant with VoIP
GW16)
H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and
G.711 CODEC methods.
4-channel VoIP gateway card. Compliant with VoIP
H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and
G.711 CODEC methods.
Note
For the maximum number of optional service cards that can be installed in the PBX, refer to "1.4.3
System Capacity".
30
Installation Manual
1.4 Specifications
1.4
Specifications
1.4.1
General Description
Control Bus
Original bus (16-bit, 8 MHz, 10 megabytes per second)
Communication Bus
H.100 bus conformity (1024 time slots)
Switching
Non-blocking
Power Input
PSU-S
100 V AC to 130 V AC; 1.4 A/200 V AC to 240 V AC; 0.8 A;
50 Hz/60 Hz
PSU-M
100 V AC to 130 V AC; 2.5 A/200 V AC to 240 V AC; 1.4 A;
50 Hz/60 Hz
PSU-L
100 V AC to 130 V AC; 5.1 A/200 V AC to 240 V AC; 2.55 A;
50 Hz/60 Hz
Maximum Power Failure Tolerance*1
+36 V DC (+12 V DC × 3, recommended maximum capacity
is 28 Ah)
Maximum Power Failure Tolerance
300 ms (without using backup batteries)
Memory Backup Duration
7 years
Dialing
CO Line
Dial Pulse (DP) 10 pps, 20 pps
Tone (DTMF) Dialing
Extension
Dial Pulse (DP) 10 pps, 20 pps
Tone (DTMF) Dialing
Mode Conversion
DP-DTMF, DTMF-DP
Ring Frequency
20 Hz/25 Hz (selectable)
Central Office Loop Limit
1600 Ω maximum
Operating
Environment
Temperature
0 °C to 40 °C (32 °F to 104 °F)
Humidity
10 % to 90 % (non-condensing)
Conference Call CO Line
From 10 × 3-party conference call to 4 × 8-party conference
call
Music on Hold (MOH)
2 ports (Level Control: -11 dB to +11 dB in 1 dB steps)
MOH1: External Music Source port
MOH2: Selectable Internal/External Music Source port
Paging
Serial Interface Port
Internal
Level Control: -15 dB to +6 dB in 3 dB steps
External
2 ports (Volume Control: -15 dB to +15 dB in 1 dB steps)
RS-232C
1 (maximum 115.2 kbps)
RJ45
Installation Manual
31
1.4 Specifications
Extension Connection Cable
Dimension
Weight (when fully
mounted)
*1
32
SLT
1-pair wire (T, R)
DPT
1-pair wire (D1, D2) or
2-pair wire (T, R, D1, D2)
APT
2-pair wire (T, R, D1, D2)
PT-interface CS (Basic/
High-density)
1-pair wire (D1, D2)
DSS Console and Add-on
Key Module
1-pair wire (D1, D2)
KX-TDE100
334 mm (W) × 390 mm (H) × 272 mm (D)
(13-1/3 in × 15-3/5 in × 10-3/4 in)
KX-TDE200
430 mm (W) × 415 mm (H) × 276 mm (D)
(17-1/5 in × 16-3/5 in × 10-7/8 in)
KX-TDE100
Under 12 kg (26.4 lb)
KX-TDE200
Under 16 kg (35.2 lb)
If tolerance may be exceeded, an Uninterruptible Power Supply (UPS) is recommended.
Installation Manual
1.4 Specifications
1.4.2
Characteristics
PT: KX-T7600 series DPT: 90 Ω; all other DPTs/APTs: 40 Ω
SLT: 600 Ω including set
Doorphone: 20 Ω
CS: 130 Ω; PT-interface CS (Basic/High-density): 65 Ω
Terminal Equipment Loop Limit
•
•
•
•
Minimum Leakage Resistance
15 000 Ω minimum
Maximum Number of Extension
Instruments per Line
1 for PT or SLT
2 by Parallel or eXtra Device Port connection of an APT/DPT and an SLT
3 by Digital eXtra Device Port connection of 2 DPTs and an SLT
Ring Voltage
75 Vrms at 20 Hz/25 Hz depending on the Ringing Load
Central Office Loop Limit
1600 Ω maximum
Hookswitch Flash Timing Range
24 ms to 2032 ms
Door Opener Current Limit
24 V DC/30 V AC, 1 A maximum
External Relay Current Limit
24 V DC/30 V AC, 1 A maximum
External Sensor Current Limit
Power to the external sensor is provided from the EIO4 card and must be
grounded through the EIO4 card. For the connection diagram, refer to
"3.7.3 EIO4 Card (KX-TDA0164)". The PBX detects input from the sensor
when the signal is under 100 Ω.
Paging Terminal Impedance
600 Ω
MOH (Music on Hold) Terminal
Impedance
10 000 Ω
Installation Manual
33
1.4 Specifications
1.4.3
System Capacity
Type and Maximum Number of Slots
The PBX supports the following type and number of slots.
Slot Type
Maximum Number
KX-TDE100
KX-TDE200
IPCMPR Card Slot
Free Slot
11
Virtual CO Line Slot
Virtual Extension Slot
Virtual Slot
IPCMPR Card Slot and Free Slots
KX-TDE100
KX-TDE200
IPCMPR Card Slot
Free Slots 1 to 6 (from the left)
IPCMPR Card Slot
Free Slots 1 to 11 (from the left)
Virtual Slots of the IPCMPR Card
Virtual
CO Line Slots
IPCMPR Card
34
Installation Manual
Virtual
Extension Slots
Virtual Slots
1.4 Specifications
Maximum Optional Service Cards
The following number of cards can be installed in the Free Slots or Virtual Slots of the PBX.
Notes
•
•
Any card that exceeds the capacity of the PBX will be ignored.
When the PBX starts up with an invalid configuration, some cards will be ignored.
Cards Installed in Free Slots or Virtual Slots
Card Type
IPCMPR
CO Line Card
Virtual CO Line Card
V-IPGW16
Physical CO Line Card
LCOT8
LCOT16
T1
PRI23
IP-GW4E
IP-GW16
Extension Card
Virtual Extension Card
V-IPEXT32
V-SIPEXT32
Physical Extension Card
DHLC8
DLC8
DLC16
SLC8
SLC16
MSLC16
IP-EXT16
CSIF4
CSIF8
OPB3
Total
*1
*2
Maximum Number
KX-TDE200
KX-TDE100
Total 6 *1
Total 8 *2
Total 6
Total 8
14
16
When installing T1 and PRI23 cards, make sure that the number of these cards
IP-GW4E cards) does not exceed 8.
One T1 or PRI23 card counts as 2 cards.
2 + the number of the other cards (including
Installation Manual
35
1.4 Specifications
Cards Mounted on Other Optional Service Cards
Maximum Number
Card Type
Mounted on
KX-TDE100
KX-TDE200
DSP16
DSP64
IPCMPR Card
RMT
EXT-CID
DPH4
2*1
2*1
MSG4
EIO4
ECHO16
*1
SLC8 Card
OPB3 Card
Only 1 ECHO16 card can be mounted on each OPB3 card.
Maximum CO Line and Extension
The PBX supports the following number of CO lines and extensions.
Type
KX-TDE100
KX-TDE200
128
128
CO Line (Physical CO Line Card)
120
128
CO Line (Virtual CO Line Card)
32
32
256
256
Extension (Physical Extension Card)
160
256
Extension (Virtual Extension Card)
128
128
IP-PT and IP Softphone
64
64
SIP Extension
128
128
Total Number of CO Line
Total Number of Extension
36
Installation Manual
1.4 Specifications
Maximum Terminal Equipment
The following shows the number of each terminal equipment type supported by the PBX.
Terminal Equipment Type
KX-TDE100
KX-TDE200
Telephone
256
256
SLT
96
128
KX-T7600 series DPT
128
256
Other DPT
32
128
APT
24
64
IP-PT
160
160
IP-PT*1 (supported by IP-EXT16
card)
96
128
IP-PT*2 (supported by IPCMPR
card)
64
64
128
128
DSS console
Basic CS
32
32
High-density CS
16
16
PS
128
128
Voice Processing System (VPS)
Doorphone
16
16
Door Opener
16
16
External Sensor
16
16
External Relay
16
16
SIP Extension
*1
*2
KX-NT136 and KX-NT265
KX-NT300 series and KX-NT265 (software version 2.00 or later only)
Installation Manual
37
1.4 Specifications
Note for KX-NT265 IP-PT users
The supported card varies depending on the software version of your KX-NT265 IP-PT. To confirm the
version, follow the procedure below:
While starting up
SP-PHONE
PROGRAM
SP-PHONE
"AP Version".
Select
"Version display".
Select
"Maintenance".
To exit the programming mode
SP-PHONE
Software version
is displayed.
HOLD
HOLD
HOLD
HOLD
Power Supply Unit Selection
The PBX needs a power supply unit (PSU) suitable for its configuration. Calculate the load figure from the
type and number of items of equipment to be connected, and determine the type of PSU that will be
required.
Load Figure Calculation
Equipment Type
PT
Extension Card*1
KX-T7600 series DPT/KX-T7600 series DSS
console
Other DPT/Other DSS console
APT
IP-PT
SIP Extension
DHLC8
SLC8
SLC16
16
MSLC16
16
Basic CS (1 unit)
High-density CS (1 unit)
VPS (1 port)
*1
38
Load Figure
Only the extension cards that can support SLTs count for the load figures.
Installation Manual
1.4 Specifications
PSU Capacity
Each PSU supports a different load figure.
PSU Type
Maximum Load Figure
PSU-S (for KX-TDE100 only)
64
PSU-M
128
PSU-L (for KX-TDE200 only)
512
Calculation Example (KX-TDE200)
Equipment Type
Load Figure
KX-T7600 series DPT
48 units
48
Other DPT
2 units
SLC16
1 card
16
MSLC16
1 card
16
VPS
8 ports
Total
96
The total load figure is 96. As this is between 64 and 128, you should install the PSU-M. But if you expect
expansion in the future, it may be better to install the PSU-L. There is no harm in installing a PSU that is
larger than is required for the current configuration.
Installation Manual
39
1.4 Specifications
40
Installation Manual
Section
Activation Key Installation
This section describes information on activation keys,
including how to obtain an activation key and install it in the SD
Memory Card.
Installation Manual
41
2.1 Information about the Activation Keys
2.1
Information about the Activation Keys
2.1.1
Activation Keys
To use IP CO lines and IP telephones on a private IP network using the IPCMPR card or to upgrade the
software for enhanced features, you need the appropriate activation keys.
Type and Maximum Number of Activation Keys
The PBX supports the following type and number of activation keys:
Description
Maximum
Number
Supported IP CO
Lines/IP Telephones
SHGW4
Allows the use of 4 IP CO lines via a
V-IPGW16 card.
32 IP CO lines
IPPT8
Allows the use of 8 IP-PTs via a VIPEXT32 card.
64 IP-PTs/IP softphones
IPPTS8
Allows the use of 8 IP-PTs/IP
softphones via a V-IPEXT32 card.
SPE16
Allows the use of 16 SIP Extensions
via a V-SIPEXT32 card.
128 SIP Extensions
UCAV2
Upgrades software to use enhanced
features.
Activation Key Type
Pre-installed Activation Keys in the DSP16/DSP64
The following type and number of activation keys are pre-installed on the DSP16/DSP64 card:
Card Type
Activation Key
Supported IP CO Lines/IP-PTs
SHGW4
4 IP CO lines
IPPT8
8 IP-PTs
SHGW4
16 IP CO lines
IPPT8
32 IP-PTs
DSP16
DSP64
Depending on the number of IP CO lines and IP-PTs to be used, you need to select either the DSP16 or
DSP64 card.
42
Installation Manual
2.1 Information about the Activation Keys
Additional Activation Keys in the SD Memory Card (Activation Key Files)
In addition to the pre-installed activation keys on the DSP16/DSP64 card, the following type and number of
activation keys are installed in the SD Memory Card:
Activation Key
Type
Maximum Number
Supported IP CO Lines/IP Telephones
with DSP16
with DSP64
with DSP16
with DSP64
28 IP CO lines
16 IP CO lines
56 IP-PTs/IP
softphones
32 IP-PTs/IP
softphones
SHGW4
IPPT8
IPPTS8
SPE16
128 SIP Extensions
UCAV2
If the pre-installed activation keys in the DSP card are not enough for the desired configuration or if you wish
to use enhanced features, it is necessary to obtain additional activation keys in the form of activation key
files and install them in the SD Memory Card. For information about how to obtain the additional activation
keys, refer to "2.1.2 Activation Key Card and Key Management System". For information about how to install
the activation key files in the SD Memory Card, refer to "2.1.3 Activation Key File".
Activation Key Installation Example
The following shows an example of when using 32 IP CO lines, 32 IP-PTs, 32 IP softphones, and 64 SIP
Extensions on a private IP network using the IPCMPR card.
Virtual CO Line
Slots
Virtual Extension
Slots
IPCMPR Card
SD Memory Card
SHGW4
DSP64 Card
SHGW4
SPE16
16 IP CO lines
16 IP CO lines
IPPTS8
IPPT8
64 SIP Extensions
32 IP softphones
Total
32 IP CO lines
Total
32 IP-PTs
32 IP softphones
64 SIP Extensions
32 IP-PTs
Virtual Slots
Installation Manual
43
2.1 Information about the Activation Keys
2.1.2
Activation Key Card and Key Management System
To obtain additional activation keys, you need to purchase the appropriate activation key cards and access
the Key Management System. You can download the activation keys as an activation key file from the Key
Management System. To download the activation keys, enter the MPR ID number shown on the IPCMPR
card in the PBX, and activation key number and registration ID provided on each activation key card.
The following activation key cards are available:
Model No.
Description
KX-NCS4104
4-Channel IP Trunk Activation Key
KX-NCS4208
8-Channel IP Softphone/IP
Provides the activation key number and
Proprietary Telephone Activation Key registration ID to download the IPPTS8
activation key.
KX-NCS4508
8-Channel IP Proprietary Telephone
Activation Key
KX-NCS4716
16-Channel SIP Extension Activation Provides the activation key number and
Key
registration ID to download the SPE16
activation key.
KX-NCS4910
Activation Key for Software Upgrade
to Enhanced Version
Notes
•
•
•
•
•
44
Card Name
Provides the activation key number and
registration ID to download the SHGW4
activation key.
Provides the activation key number and
registration ID to download the IPPT8 activation
key.
Provides the activation key number and
registration ID to download the UCAV2
activation key.
You can only download the activation key file once using the activation key number and registration
ID provided on the activation key card.
Up to 8 activation keys can be downloaded as one activation key file.
It is possible to send the activation key file to a specified e-mail address at the same time as
downloading it to a PC.
Make sure to backup the downloaded activation key files on your PC.
In the event of a system malfunction, you need a temporary activation key for maintenance
purposes. The temporary activation key can be downloaded from the Key Management System in
the same way as downloading activation key files.
Installation Manual
2.1 Information about the Activation Keys
2.1.3
Activation Key File
The corresponding number of IP CO lines and IP telephones or enhanced features can be activated by
installing the downloaded activation key file(s) in the SD Memory Card of the IPCMPR card using the KXTDE Maintenance Console.
Installing the Activation Key File in the SD Memory Card
Make sure to install the KX-TDE Maintenance Console on the PC in advance, and connect the PC to the
PBX. For details about the KX-TDE Maintenance Console, refer to "Guide for the KX-TDE Maintenance
Console".
1. Start the KX-TDE Maintenance Console from the Start menu on the PC.
2. From the Utility menu, select File Transfer PC to PBX (SD Card).
A dialogue box will be displayed.
3. Select the file to upload.
A window showing the upload progress will be displayed.
While transferring files to the SD memory card, the PBX automatically renames them according to the
header information.
A message will be displayed when the transfer is complete.
4. Click OK.
Note
It is necessary to restart the PBX to activate the UCAV2 activation key after performing the procedure
above. To restart the PBX, refer to "5.1.4 Using the Reset Button".
CAUTION
The activation key file can only be installed in the PBX with the MPR ID number entered when the
activation key file was downloaded. The activation key file cannot be reissued unless the IPCMPR card
crashes.
Installation Manual
45
2.1 Information about the Activation Keys
46
Installation Manual
Section
Installation
This section describes the procedures to install the PBX.
Detailed instructions for planning the installation site, installing
the shelves and optional service cards, and cabling of
peripheral equipment are provided. Further information on
system expansion and peripheral equipment installation is
included.
Installation Manual
47
3.1 Before Installation
3.1
Before Installation
3.1.1
Before Installation
Please read the following notes concerning installation and connection before installing the PBX and
terminal equipment.
Be sure to comply with all applicable laws, regulations, and guidelines.
Safety Installation Instructions
When installing telephone wiring, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and injury to persons, including the following:
1. Never install telephone wiring during a lightning storm.
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected
at the network interface.
4. Use caution when installing or modifying telephone lines.
5. Anti-static precautions should be taken during installation.
Installation Precautions
This set is made for wall mounting (KX-TDE100/KX-TDE200) or floor standing (KX-TDE200 only), and
should be installed in a location where it is accessible for inspections and maintenance.
To prevent malfunction, noise, or discoloration, avoid installing the system in the following locations:
1.
2.
3.
4.
5.
6.
In direct sunlight and hot, cold, or humid places. (Temperature range: 0 ˚C to 40 ˚C)
Areas where sulfuric gases may be present, such as near thermal springs.
Areas where shocks or vibrations are frequent or strong.
High-dust areas, or places the system may come into contact with water or oil.
Near devices that generate high frequencies, such as sewing machines or electric welders.
On or near computers, telexes, or other office equipment, as well as microwave ovens or air
conditioners. (It is preferable not to install the system in the same room as the above equipment.)
7. Within 1.8 m (6 ft) of radios and televisions. (Both the PBX and PTs should be at least 1.8 m (6 ft) away
from such devices).
8. Locations where other objects will obstruct the area around the PBX. Be especially careful to leave at
least 20 cm (8 in) of space above and 10 cm (4 in) to the sides of the PBX for ventilation.
9. Do not block the openings of the PBX.
10. Do not stack up the optional service cards.
Wiring Precautions
Be sure to follow these instructions when wiring the unit:
1. Do not run unshielded telephone cables near AC power cables, computer cables, AC power sources,
etc. When running cables near other noise-generating devices or cables, use shielded telephone
cables or shield the telephone cables with metal tubing.
2. If cables are run on the floor, use protectors to prevent the cables from being stepped on. Avoid running
cables under carpets.
48
Installation Manual
3.1 Before Installation
3. Avoid using the same AC outlet for computers, telexes, and other office equipment, as noise generated
by such equipment may hamper system performance or interrupt the system.
4. Use 2-pair telephone cables when connecting PTs.
Use 1-pair telephone cables when connecting SLTs, data terminals, answering machines, computers,
Voice Processing Systems, etc.
5. Unplug the system from its power source when wiring, and plug the system back in only after all wiring
is completed.
6. Mis-wiring may cause the PBX to operate improperly. Refer to Section 2 "Installation" when wiring the
system.
7. If an extension does not operate properly, disconnect the telephone from the extension line and connect
it again, or turn off the PBX using the power switch, then turn it on again.
8. For safety purposes this unit is equipped with a grounded plug. If you do not have a grounded outlet,
please have one installed. Do not bypass this safety feature by tampering with the plug.
9. Use twisted pair cable for CO line connection.
10. CO Lines should be installed with surge protectors. For details, refer to "3.2.13 Surge Protector
Installation".
11. To assure good quality telephone connection, it is recommended new and modifications to existing
installation of customer premise wiring shall use solid twisted pair copper conductors with minimum 24
gauge that comply with the electrical specifications for Category 3 wiring as detailed in ANSI/EIA/TIA570A Building Wiring Standards.
Installation Manual
49
3.2 Installation of the PBX
3.2
Installation of the PBX
3.2.1
Unpacking
Unpack the box and check the items below:
50
KX-TDE100
KX-TDE200
Main Unit
Ferrite Core (for the IPCMPR card)
Metal Bracket
Screw A
Screw B (Black)
Anchor Plug
Mini Plug (for pager and music source)
SD Memory Card
Installation Manual
3.2 Installation of the PBX
3.2.2
Names and Locations
Inside View
KX-TDE100
KX-TDE200
E F
A.
B.
C.
D.
E.
F.
G.
H.
I.
RUN Indicator
ALARM Indicator
RJ45 Ports
RS-232C Port
PSU Slot
Null Slot (not available for any optional service card)
Free Slots 1 to 6 (from the left)
IPCMPR Card Slot
Free Slots 1 to 11 (from the left)
Installation Manual
51
3.2 Installation of the PBX
3.2.3
Opening/Closing the Front Cover
Opening the Front Cover
1. Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw
cover.
Screw Cover
2. Turn the screw anticlockwise to loosen.
3. Slide the front cover to the right until it stops, then lift the front cover.
52
Installation Manual
3.2 Installation of the PBX
Closing the Front Cover
1. Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the
shelf). Then slide the front cover to the left until it locks.
2. Turn the screw clockwise to tighten.
3. Secure the screw cover.
Notes
•
•
For safety reasons, close the front cover and tighten the screw before operating the PBX.
Do not forget to tighten the screw before securing the screw cover.
Installation Manual
53
3.2 Installation of the PBX
3.2.4
Installing/Replacing the Power Supply Unit
Function
PSU Type
Lower/Upper Input Voltage Range
Current
PSU-S
(for KX-TDE100)
Lower: 100 V AC to 130 V AC
1.4 A
Upper: 200 V AC to 240 V AC
0.8 A
PSU-M
(for KX-TDE100/KXTDE200)
Lower: 100 V AC to 130 V AC
2.5 A
Upper: 200 V AC to 240 V AC
1.4 A
PSU-L
(for KX-TDE200)
Lower: 100 V AC to 130 V AC
5.1 A
Upper: 200 V AC to 240 V AC
2.55 A
PSU-S
Input Frequency
50 Hz or 60 Hz
PSU-M/PSU-L
Ground Terminal
Power Switch
Ground Terminal
AC Inlet
Power Switch
AC Inlet
Accessories and User-supplied Items
Accessories (included): Screws × 4, AC power cord × 1
User-supplied (not included): Grounding wire
Notes
•
For details about frame ground connection, refer to "3.2.5 Frame ground Connection".
Safety Instructions
Each PSU complies with Safety Class 1 of IEC60950, EN60950, UL60950,
CAN/CSA-C22.2 No.60950, and AS/NZS60950; therefore a protective ground connection exists between
the mains outlet ground and the PSU case. To ensure the PBX chassis is safely grounded, it is essential
that the PSU case be securely fastened to the PBX chassis with the 4 screws provided with each PSU.
When installing or replacing a PSU, basic safety precautions should always be followed to reduce the risk
of fire, electric shock and injury to persons, including the following:
1. Never install or replace a PSU during a lightning storm.
2. Never install or replace a PSU in wet locations.
3. Never install or replace a PSU unless at least 20 s has elapsed after the AC supply is disconnected.
54
Installation Manual
3.2 Installation of the PBX
4. To protect the back board from static electricity, do not touch parts on the back board in the main
unit and PSU. To discharge static electricity, touch ground or wear a grounding strap.
The following procedures are for installing or replacing a PSU only. Do not replace or remove the
PSU for any other purpose.
Installing the Power Supply Unit
1. Insert the PSU along the guide rails.
CAUTION
For safety reasons, do not touch parts in the PSU.
Guide Rail
Installation Manual
55
3.2 Installation of the PBX
2. Push the release lever in the direction of the arrow, so that the PSU engages securely with the
connector on the back board.
Back Board
Release Lever
3. Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU.
3 2
Screws
4 1
Replacing the Power Supply Unit
1. Unplug the AC power cord.
56
Installation Manual
3.2 Installation of the PBX
2. Turn the 4 screws anticlockwise to loosen them.
Screws
3. Pull the release lever in the direction of the arrow to disconnect the PSU from the back board.
Back Board
Release Lever
4. Replace the PSU.
New PSU
Current PSU
5. Follow the steps in "Installing the Power Supply Unit".
Installation Manual
57
3.2 Installation of the PBX
3.2.5
Frame ground Connection
IMPORTANT
Connect the frame of the PBX to ground.
1. Loosen the screw.
2. Insert a grounding wire (user-
Screw
supplied)*.
3. Tighten the screw.
4. Connect the grounding wire to
ground.
Grounding
wire
To earth
* For grounding wire, green-and-yellow insulation is required, and the cross-sectional area of the
conductor must be more than 0.75 mm2 or 18 AWG.
•
•
•
Be sure to comply with applicable local regulations (e.g., laws, guidelines).
Proper grounding (connection to ground) is very important to protect the PBX from the bad effects of
external noise or to reduce the risk to the user of electrocution in the case of a lightning strike.
The grounding wire of the AC cable has an effect against external noise and lightning strikes, but it may
not be enough to protect the PBX. A permanent connection between ground and the ground terminal
of the PBX must be made.
In most of the continental United States, the ground provided by the "Third wire ground" at the commercial
power outlet will be satisfactory. However, in a small percentage of cases this ground may be installed
incorrectly. Therefore, the following test procedure should be performed.
Test Procedure
1. Obtain a suitable voltmeter and set it for a possible reading of up to 250 V AC.
2. Connect the meter probes between the 2 main AC voltage points on the wall outlet. The reading
obtained should be 108 V AC to 132 V AC.
3. Move one of the meter probes to the 3rd prong terminal (GND).
Either the same reading or a reading of 0 volt should be obtained.
4. If a reading of 0 volt at one terminal and a reading of 108 V AC to 132 V AC at the other terminal
is not obtained, the outlet is not properly grounded.
This condition should be corrected by a qualified electrician (per article 250 of the National
Electrical Code).
5. If a reading of 0 volt at one terminal and a reading of 108 V AC to 132 V AC at the other terminal
is obtained, then set the meter to the "OHMS/RX1" scale, place one probe at the GND Terminal
and the other probe at the terminal which gave a reading of 0 volt.
A reading of less than 1 ohm should be obtained. If the reading is not obtained, the outlet is not
adequately grounded. See qualified electrician.
58
Installation Manual
3.2 Installation of the PBX
3.2.6
Installing/Removing the Optional Service Cards
CAUTION
To protect the back board from static electricity, do not touch parts on the back board in the main unit
and on the optional service cards. To discharge static electricity, touch ground or wear a grounding
strap.
Note
The optional service cards can be installed or removed while the DC power is supplied. However, when
installing or removing the IPCMPR card, the DC power supply must be turned off.
Installing Optional Service Cards
1. Insert the card along the guide rails.
Guide Rail
Installation Manual
59
3.2 Installation of the PBX
2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card
engages securely with the connector on the back board.
Back Board
Release Lever
3. Turn the 2 screws clockwise to fix the card in place.
Screws
Note
Make sure the screws are tightened to ground the card securely.
60
Installation Manual
3.2 Installation of the PBX
Covering the Blank Slots
Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover.
CAUTION
Failure to install the Blank Slot Cover may cause electromagnetic interference.
Installation Manual
61
3.2 Installation of the PBX
Handling of the Cables
When cables are connected to the PBX, run the cables to either the right or the left and then towards the
back of the shelf as shown below.
Note
For safety reasons, do not stretch, bend, or pinch the AC power cord.
62
Installation Manual
3.2 Installation of the PBX
Removing the Optional Service Cards
1. Turn the 2 screws anticlockwise to loosen them.
Screws
2. Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the
card from the shelf to remove it.
Back Board
Release Lever
Installation Manual
63
3.2 Installation of the PBX
3.2.7
Types of Connectors
Connector Type
Pin Number
RJ11
Used for
•
•
•
•
•
•
DHLC8 (KX-TDA0170)
SLC8 (KX-TDA0173)
SLC16 (KX-TDA0174)
MSLC16 (KX-TDA0175)
LCOT8 (KX-TDA0180)
LCOT16 (KX-TDA0181)
•
•
•
•
•
•
•
•
IPCMPR
CSIF4 (KX-TDA0143)
CSIF8 (KX-TDA0144)
T1 (KX-TDA0187)
PRI23 (KX-TDA0290)
IP-EXT16 (KX-TDA0470)
IP-GW4E (KX-TDA0484)
IP-GW16 (KX-TDA0490)
•
•
•
•
•
•
•
•
DHLC8 (KX-TDA0170)
DLC8 (KX-TDA0171)
DLC16 (KX-TDA0172)
SLC8 (KX-TDA0173)
SLC16 (KX-TDA0174)
MSLC16 (KX-TDA0175)
LCOT8 (KX-TDA0180)
LCOT16 (KX-TDA0181)
•
•
DPH4 (KX-TDA0161)
EIO4 (KX-TDA0164)
•
Basic Shelf
(Twisted pair cable)
RJ45
(Twisted pair cable)
Amphenol
Type A Type B
50
25
26
(Shielded twisted pair
cable)
10-pin
8-pin
Terminal Terminal
Block
Block
10
RS-232C
64
Installation Manual
3.2 Installation of the PBX
Connector Type
Pin Number
Used for
•
IPCMPR
Mini Plug
Installation Manual
65
3.2 Installation of the PBX
3.2.8
Attaching a Ferrite Core
A ferrite core must be attached when:
•
an RJ45 connector is connected to an IPCMPR, IP-GW16 or IP-EXT16 cards, or
•
an Amphenol connector is connected to an extension card.
Attaching to an RJ45 Connector
For the IPCMPR Card
Wrap the cable once around the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3
cm (1-3/16 in) away from the connector. The ferrite core is included with the PBX.
3 cm
(1-3/16 in)
For IP-GW16/IP-EXT16 Cards
Wrap the cable once around the ferrite core, then close the case of the ferrite core. Attach the ferrite core 5
cm (1-15/16 in) away from the connector. The ferrite core is included with the card.
5 cm
(1-15/16 in)
66
Installation Manual
3.2 Installation of the PBX
Attaching to an Amphenol Connector
For Extension Cards
Pass the cable through the ferrite core, then close the case of the ferrite core. Attach the ferrite core 3 cm
(1-3/16 in) away from the connector. The ferrite core is included with the card.
3 cm
(1-3/16 in)
If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core.
Installation Manual
67
3.2 Installation of the PBX
3.2.9
Fastening an Amphenol Connector
An Amphenol 57JE-type connector is used on some of the optional service cards.
To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro ® tape
to fix the lower part of the connector.
Type A (Spring Latch + Velcro Tape)
Type B (Screw + Velcro Tape)
Velcro
Tape
Velcro
Tape
Spring
Latch
Remove the
screw on the
optional service
card.
Spring
Latch
Insert the screw (included
with the Amphenol or
optional service card).
68
Installation Manual
3.2 Installation of the PBX
Amphenol Connector Pin Assignment Chart
Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol
connector. For more details, refer to the appropriate section in "3.5 Information about the Physical Trunk
Cards" and "3.6 Information about the Physical Extension Cards".
Pin No. LCOT8
RA
26
TA
RB
27
TB
RC
28
TC
RD
29
TD
RE
30
TE
RF
31
TF
RG
32
TG
RH
33
TH
34
10
35
11
36
12
37
13
38
14
39
15
40
16
41
17
42
18
43
19
44
20
45
21
46
22
47
23
48
24
49
25
50
LCOT16
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
RI
TI
RJ
TJ
RK
TK
RL
TL
RM
TM
RN
TN
RO
TO
RP
TP
DHLC8
RA
TA
D2A
D1A
RB
TB
D2B
D1B
RC
TC
D2C
D1C
RD
TD
D2D
D1D
RE
TE
D2E
D1E
RF
TF
D2F
D1F
RG
TG
D2G
D1G
RH
TH
D2H
D1H
DLC8
D2A
D1A
D2B
D1B
D2C
D1C
D2D
D1D
D2E
D1E
DLC16
D2A
D1A
D2B
D1B
D2C
D1C
D2D
D1D
D2E
D1E
D2F
D1F
D2G
D1G
D2H
D1H
D2I
D1I
D2J
D1J
D2K
D1K
D2L
D1L
D2M
D1M
D2N
D1N
D2O
D1O
D2P
D1P
MSLC16
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
RI
TI
RJ
TJ
RK
TK
RL
TL
RM
TM
RN
TN
RO
TO
RP
TP
SLC16
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
RG
TG
RH
TH
RI
TI
RJ
TJ
RK
TK
RL
TL
RM
TM
RN
TN
RO
TO
RP
TP
SLC8
RA
TA
RB
TB
RC
TC
RD
TD
RE
TE
RF
TF
D2F
D1F
RG
TG
D2G
D1G
RH
TH
D2H
D1H
Installation Manual
69
3.2 Installation of the PBX
3.2.10 Wall Mounting (KX-TDE200)
CAUTION
•
•
Notes
•
•
•
•
Make sure that the wall the shelf will be attached to is capable of supporting at least 4 times the
weight of the shelf.
Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or
metal plates in the wall.
Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in)
at the sides of the shelf.
Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on
the back of the shelf will not be blocked.
Make sure that the surface behind the shelf is not made of wood.
Be careful not to drop the shelf.
1. Install 4 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 4
screws (A).
Anchor Plug
Wall
Hammer
Anchor Plug
Metal Bracket
8 mm
(5/16 in)
30 mm
(1-3/16 in)
Screw (A)
Screw (A)
Metal Bracket
70
Installation Manual
3.2 Installation of the PBX
2. Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts
of the metal bracket. Use 2 screws (B) to fix both sides of the shelf.
TOP
Screw (B)
Installation Manual
71
3.2 Installation of the PBX
3.2.11 Wall Mounting (KX-TDE100)
CAUTION
•
•
Notes
•
•
•
•
Make sure that the wall the shelf will be attached to is capable of supporting at least 4 times the
weight of the shelf.
Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or
metal plates in the wall.
Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in)
at the sides of the shelf.
Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on
the back of the shelf will not be blocked.
Make sure that the surface behind the shelf is not made of wood.
Be careful not to drop the shelf.
1. Install 3 anchor plugs in the wall, using the metal bracket as a template. Fix the metal bracket with 3
screws (A).
Anchor Plug
Hammer
Anchor Plug
Wall
8 mm
(5/16 in)
Metal Bracket
30 mm
(1-3/16 in)
TOP
Screw (A)
TOP
Screw (A)
Metal Bracket
72
Installation Manual
3.2 Installation of the PBX
2. Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts
of the metal bracket. Use 2 screws (B) to fix both sides of the shelf.
TOP
Screw (B)
Installation Manual
73
3.2 Installation of the PBX
3.2.12 Floor Standing (KX-TDE200 Only)
Notes
•
•
•
•
Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in)
at the sides of the shelf.
Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on
the back of the shelf will not be blocked.
Make sure that the surface behind the shelf is not made of wood.
Be careful not to drop the shelf.
1. Install 4 anchor plugs in the floor, using the metal bracket as a template. Fix the metal bracket with 4
screws (A).
Screw (A)
Metal Bracket
TOP
Screw (A)
Anchor
Plug
Hammer
Anchor
Plug
30 mm
(1-3/16 in)
Floor
8 mm
(5/16 in)
2. Remove the front cover of the shelf (refer to "3.2.3 Opening/Closing the Front Cover").
74
Installation Manual
Metal
Bracket
3.2 Installation of the PBX
3. Lift the shelf, attach it to the metal bracket, slide it backwards until it locks, and retain it with 2 screws (B).
TOP
FRONT
Screws (B)
Metal Bracket
4. Fix the front cover on the shelf (refer to "3.2.3 Opening/Closing the Front Cover").
Installation Manual
75
3.2 Installation of the PBX
3.2.13 Surge Protector Installation
Overview
A massive electrical surge can be caused if lightning strikes a telephone cable 10 m (33 ft) above ground,
or if a telephone line comes into contact with a power line. A surge protector is a device that is connected
to a CO line to prevent potentially dangerous electrical surges from entering the building via the CO line and
damaging the PBX and connected equipment.
To protect the system from electrical surges, we strongly recommend connecting the system to a surge
protector that meets the following specifications:
– Surge arrestor type: 3-electrode arrestor
– DC spark-over voltage: 230 V
– Maximum peak current: at least 10 kA
Additionally, proper grounding is very important for the protection of the system (refer to "3.2.5 Frame ground
Connection").
Many countries/areas have regulations requiring surge protection. Be sure to comply with all applicable
laws, regulations, and guidelines.
Installation
CO Line
CO Line
CO Line
Surge
Protector
Terminal
Board
Extn.
PBX
Extn.
SLT
PT
PT-interface CS
Ground
76
Installation Manual
CS
Frame
Ground
Extn.: Extension line
3.2 Installation of the PBX
Outside Installation
(Main Building)
Surge Protector
CO Line
(Another Building)
CO Line
Extn.
Terminal
Board
PBX
Extn.
Surge
Protector
CS
Extn.
Extn.
SLT
PT
PT-interface CS
SLT
PT
PT-interface CS
CS
Ground
Extn.: Extension Line
If you install an extension outside of the building, the following precautions are recommended:
a. Install the extension wire underground.
b. Use a conduit to protect the wire.
Note
The surge protector for an extension and CS is different from that for CO lines.
Installation of a ground Rod
Surge Protector
CO Line
Grounding
Wire
PBX
(Underground)
Ground Rod
Installation Manual
77
3.2 Installation of the PBX
1. Connect the ground rod to the surge protector using a grounding wire with a cross-sectional area of at
least 1.3 mm2.
2. Bury the ground rod near the protector. The grounding wire should be as short as possible.
3. The grounding wire should run straight to the ground rod. Do not run the wire around other objects.
4. Bury the ground rod at least 50 cm (20 in) underground.
Notes
•
•
78
The above figures are recommendations only.
The length of ground rod and the required depth depend on the composition of the soil.
Installation Manual
3.3 Information about the Main Processing Card
3.3
Information about the Main Processing Card
3.3.1
IPCMPR Card
Function
The IPCMPR card is the pre-installed main processing card with built-in SVM feature (2-channel). The
Virtual Cards (CO line/extension) can be installed in Virtual Slots of the IPCMPR card and can be activated
with the activation keys. Also, the IPCMPR supports LAN connection so that IP telephones (IP-PTs, IP
softphones, SIP Extensions) and PCs can be connected on a private IP network.
Mountable Cards
•
•
Either one of the DSP16 or DSP64 cards (refer to "3.3.2 DSP16 Card (KX-TDE0110) and DSP64
Card (KX-TDE0111)" )
RMT card (refer to "3.3.3 RMT Card (KX-TDA0196)" )
SD
CARD
LEDs
SD Memory Card
Slot Cover
Reset Button
SD
Memory
Card 3
System Initialize
Switch
SD
CARD
RJ45
(10BASE-T/100BASE-TX
Full Duplex)
BGM/MOH
Pager
MPR ID Number
SD
CARD
RJ45 (for PC Maintenance)
To PC
To LAN
LEDs
RJ45 (for LAN Connection)
Installation Manual
79
3.3 Information about the Main Processing Card
Notes
•
•
•
•
•
•
•
•
The maximum length of the cable to be connected to the IPCMPR card is 100 m (328 ft).
When connecting the RJ45 connector, attach the ferrite core included with the PBX. Refer to "3.2.8
Attaching a Ferrite Core".
For details about Virtual Slots, refer to "1.4.3 System Capacity".
For details about the activation keys, refer to "2.1 Information about the Activation Keys".
For details about connecting to a LAN, refer to "3.12 LAN Connection".
For details about connecting peripherals, refer to "3.11.1 Connection of Peripherals".
For details about System Initialize Switch, refer to "3.14.1 Starting the PBX".
For details about Reset Button, refer to "5.1.4 Using the Reset Button".
WARNING
A LITHIUM BATTERY IS USED IN THE IPCMPR CARD. THERE IS A RISK OF EXPLOSION
IF THE BATTERY IS REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED
BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
CAUTION
•
•
•
•
Use only the SD Memory Card included with the PBX.
The SD Memory Card contains software for all the processes of the PBX and all the customer data.
The SD Memory Card must be inserted before startup.
Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the
PBX to fail to start when you try to restart the system.
To prevent data leakage, render the SD Memory Card physically unusable before disposal.
Pin Assignments
RJ45 Connector (10BASE-T/100BASE-TX)
80
Installation Manual
No.
Signal Name
Input (I)/Output (O)
Function
TPO+
Transmit data+
TPO-
Transmit data-
TPI+
Receive data+
4-5
Reserved
–
–
TPI-
Receive data-
7-8
Reserved
–
–
3.3 Information about the Main Processing Card
LED Indications
Indication
Color
Description
BATT ALARM
Red
Battery alarm indication
•
OFF: Normal
ON: Alarm
SD ACCESS
Green
SD memory card status
•
ON: Accessing
(for PC Maintenance)
(for LAN Connection)
LINK Green
Link status indication
•
OFF: Off-line
•
ON: Linked normally
•
Flashing: In communication
100
Data transmission speed indication
•
OFF: 10 Mbps
•
ON: 100 Mbps
Yellow
LINK Green
Link status indication
•
OFF: Off-line
•
ON: Linked normally
•
Flashing: In communication
100
Data transmission speed indication
•
OFF: 10 Mbps
•
ON: 100 Mbps
Yellow
Installation Manual
81
3.3 Information about the Main Processing Card
3.3.2
DSP16 Card (KX-TDE0110) and DSP64 Card (KX-TDE0111)
Function
DSP16:
DSP64:
16-channel digital signal processor card with an SHGW4 activation key and an IPPT8
activation key pre-installed. Compliant with ITU-T G.729a and G.711 CODEC methods. To be
mounted on the IPCMPR card.
64-channel digital signal processor card with four SHGW4 activation keys and four IPPT8
activation keys pre-installed. Compliant with ITU-T G.729a and G.711 CODEC methods. To
be mounted on the IPCMPR card.
inside
Screw
DSP16 Card/
DSP64 Card
Accessories and User-supplied Items
Accessories (included): Screws × 3
User-supplied (not included): none
Notes
•
•
82
Depending on the number and the type of CO lines and IP telephones you wish to use, required
activation keys are determined, and either the DSP16 or DSP64 card is selected to be installed.
If the pre-installed activation keys on the DSP16 or DSP64 cards are not enough for the desired
configuration, you need to purchase activation key cards. For details about the activation keys,
refer to "2.1 Information about the Activation Keys".
Installation Manual
3.3 Information about the Main Processing Card
3.3.3
RMT Card (KX-TDA0196)
Function
Analog modem card for remote communication with the PBX. ITU-T V.90 support. To be mounted on the
IPCMPR card.
IPCMPR Card
inside
RMT Card
Screw
Accessories and User-supplied Items
Accessories (included): Screws × 2
User-supplied (not included): none
Installation Manual
83
3.4 Information about the Virtual Cards
3.4
Information about the Virtual Cards
3.4.1
Virtual Cards
Function
Virtual Cards are included with the IPCMPR card and can be activated with the appropriate activation key.
By installing Virtual Cards in the Virtual Slots of the IPCMPR card using the KX-TDE Maintenance Console,
IP CO lines and IP extensions can be used via the IPCMPR card.
Virtual Card
Description
Virtual 16-Channel VoIP Gateway Card
(V-IPGW16)
Virtual Card for 16-channel VoIP CO line. Compliant with VoIP
H.323 V.5 protocol.
Virtual 32-Channel VoIP Extension Card Virtual Card for 32 VoIP extensions. Compliant with Panasonic
(V-IPEXT32)
proprietary protocol.
Virtual 32-Channel SIP Extension Card
(V-SIPEXT32)
Virtual Card for 32 SIP Extensions. Compliant with RFC 3261,
3264, 3310, and 2327 protocols.
Example: Virtual Cards in the Virtual Slots
Virtual CO Line
Slots
Virtual Extension
Slots
IPCMPR Card
Virtual Slots
84
Installation Manual
3.5 Information about the Physical Trunk Cards
3.5
Information about the Physical Trunk Cards
3.5.1
LCOT8 Card (KX-TDA0180) and LCOT16 Card (KXTDA0181)
Function
LCOT8:
LCOT16:
8-port analog CO line card with 2 power failure transfer (PFT) ports. One CID8 card can be
mounted on the LCOT8 card (refer to "3.5.2 CID8 Card (KX-TDA0193)").
16-port analog CO line card with 4 power failure transfer (PFT) ports. A maximum of 2 CID8
cards can be mounted on the LCOT16 card (refer to "3.5.2 CID8 Card (KX-TDA0193)").
LED
Amphenol
To CO line
Accessories and User-supplied Items
Accessories (included): Screws × 2
User-supplied (not included): Amphenol connector
Notes
•
•
•
To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector".
For details about power failure transfer, refer to "3.13.1 Power Failure Connections".
To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting
the PBX".
Installation Manual
85
3.5 Information about the Physical Trunk Cards
Pin Assignments
Amphenol Connector
50
26
Notes
•
•
25
No.
Signal Name Function
No.
Signal Name Function
RA
Ring port 1
26
TA
Tip port 1
RB
Ring port 2
27
TB
Tip port 2
RC
Ring port 3
28
TC
Tip port 3
RD
Ring port 4
29
TD
Tip port 4
RE
Ring port 5
30
TE
Tip port 5
RF
Ring port 6
31
TF
Tip port 6
RG
Ring port 7
32
TG
Tip port 7
RH
Ring port 8
33
TH
Tip port 8
RI
Ring port 9
34
TI
Tip port 9
10
RJ
Ring port 10
35
TJ
Tip port 10
11
RK
Ring port 11
36
TK
Tip port 11
12
RL
Ring port 12
37
TL
Tip port 12
13
RM
Ring port 13
38
TM
Tip port 13
14
RN
Ring port 14
39
TN
Tip port 14
15
RO
Ring port 15
40
TO
Tip port 15
16
RP
Ring port 16
41
TP
Tip port 16
17-25
Reserved
–
42-50
Reserved
–
Pin assignments for the pins 5 to 8 and 30 to 33 are for the LCOT8 and LCOT16 card only.
Pin assignments for the pins 9 to 16 and 34 to 41 are for the LCOT16 card only.
LED Indications
86
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
3.5 Information about the Physical Trunk Cards
3.5.2
CID8 Card (KX-TDA0193)
Function
8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted
on the LCOT8/LCOT16 cards.
LCOT16 card only
OFF
inside
ON
SW2
CID8 Card
Screw
SW1
ON
OFF
Accessories and User-supplied Items
Accessories (included): Screws × 2
User-supplied (not included): none
Note
Only 1 CID8 card can be mounted on the LCOT8 card.
Switch Settings (on LCOT8/LCOT16 cards)
Switch
Type
Usage and Status Definition
Port Setting
DIP
Keep all DIP switches at default "ON" positions. Do not change the
positions of these switches.
Note
SW2 is for the LCOT16 card only.
Installation Manual
87
3.5 Information about the Physical Trunk Cards
3.5.3
T1 Card (KX-TDA0187)
Function
1-port T1 CO line card. EIA/TIA standard compliant.
LEDs
RJ45
To NT1
Accessories and User-supplied Items
Accessories (included): none
User-supplied (not included): RJ45 connector
Notes
•
•
•
Connect this optional service card to the CO line through NT1; do not connect to the CO line
directly.
T1 Card must be installed behind an FCC registered and UL or CSA-NRTL listed CSU.
To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting
the PBX".
CAUTION
T1 ports are SELV ports and should only be connected to SELV services.
Switch Settings
88
Switch
Type
Usage and Status Definition
A/B
Slide
Keep the switch at default A position. Do not change the position of
this switch.
Installation Manual
3.5 Information about the Physical Trunk Cards
Pin Assignments
RJ45 Connector
No.
Signal Name
Level [V]
Function
RX+
(+)
Receive data (+)
RX-
(-)
Receive data (-)
Reserved
–
–
TX-
(-)
Transmit data (-)
TX+
(+)
Transmit data (+)
6-8
Reserved
–
–
LED Indications
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
SYNC-ERR
Red
Non-synchronisation status indication
•
OFF: Normal
•
ON: Out of synchronisation
RAI
Red
RAI signal status indication
•
OFF: Normal
•
ON: Alarm (Clock Slave)
•
Flashing (60 times per minute): Alarm (Clock Master)
AIS
Red
AIS status indication
•
OFF: Normal
•
ON: Alarm
SYNC
Green
Synchronisation status indication
•
OFF: Not synchronised
•
ON: Synchronised
•
Flashing (60 times per minute): Synchronised (Clock Master)
Installation Manual
89
3.5 Information about the Physical Trunk Cards
3.5.4
PRI23 Card (KX-TDA0290)
Function
1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol)
compliant.
LEDs
RJ45
To NT1
Accessories and User-supplied Items
Accessories (included): none
User-supplied (not included): RJ45 connector
Notes
•
•
Connect this optional service card to the CO line through an NT1; do not connect to the U interface
of the CO line directly.
To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting
the PBX".
CAUTION
PRI ports are SELV ports and should only be connected to SELV services.
Switch Settings
90
Switch
Type
Usage and Status Definition
A/B
Slide
Keep the switch at default A position. Do not change the position of
this switch.
Installation Manual
3.5 Information about the Physical Trunk Cards
Pin Assignments
RJ45 Connector
No.
Signal Name
Level [V]
Function
RX+
(+)
Receive data (+)
RX-
(-)
Receive data (-)
Reserved
–
–
TX-
(-)
Transmit data (-)
TX+
(+)
Transmit data (+)
6-8
Reserved
–
–
LED Indications
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
SYNC-ERR
Red
Non-synchronisation status indication
•
OFF: Normal
•
ON: Out of synchronisation
RAI
Red
RAI signal status indication
•
OFF: Normal
•
ON: Alarm (Clock Slave)
•
Flashing (60 times per minute): Alarm (Clock Master)
AIS
Red
AIS status indication
•
OFF: Normal
•
ON: Alarm
SYNC
Green
Synchronisation status indication
•
OFF: Not synchronised
•
ON: Synchronised
•
Flashing (60 times per minute): Synchronised (Clock Master)
D-LINK
Green
Data link status indication
•
OFF: Not established
•
ON: Established
Installation Manual
91
3.5 Information about the Physical Trunk Cards
3.5.5
IP-GW4E Card (KX-TDA0484)
Function
4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and
G.711 CODEC methods.
LEDs
RJ45
(10BASE-T/100BASE-TX)
To private IP network
Accessories and User-supplied Items
Accessories (included): CD-ROM (including documentation for web programming) × 1
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
The maximum length of the cable to be connected to this optional service card is 100 m (328 ft).
The IP-GW4E card occupies the space of only 1 free slot when it is installed in the PBX.
For programming instructions and other information about the IP-GW4E card, refer to the
documentation for the IP-GW4E card. To program the IP-GW4E card, use the web programming
designed for the IP-GW4E card.
To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting
the PBX".
Pin Assignments
RJ45 Connector (10BASE-T/100BASE-TX)
92
Installation Manual
No.
Signal Name
Input (I)/Output (O)
Function
TPO+
Transmit data+
TPO-
Transmit data-
TPI+
Receive data+
4-5
Reserved
–
–
TPI-
Receive data-
7-8
Reserved
–
–
3.5 Information about the Physical Trunk Cards
LED Indications
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
ONLINE
Green
On-line status indication
•
ON: On-line mode
•
OFF: Off-line mode
•
Flashing: Maintenance mode
Note
If the LINK indicator is OFF, the ONLINE indicator will also be
OFF.
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm
VoIP BUSY
Green
VoIP (H.323) process indication
•
OFF: VoIP process inactive
•
ON: VoIP process active
LINK
Green
Link status indication
•
OFF: Connection error
•
ON: Normal connection
DATA
Green
Data transmission indication
•
OFF: No data transmitted
•
ON: Data transmitting
Installation Manual
93
3.5 Information about the Physical Trunk Cards
3.5.6
IP-GW16 Card (KX-TDA0490)
Function
16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1 and
G.711 CODEC methods.
LEDs
RJ45
(10BASE-T/100BASE-TX
Full Duplex)
To private IP network
Accessories and User-supplied Items
Accessories (included): Ferrite core × 1, CD-ROM (including documentation for web programming) × 1
User-supplied (not included): RJ45 connector
Notes
•
•
•
•
The maximum length of the cable to be connected to this optional service card is 100 m (328 ft).
When connecting the RJ45 connector, attach the included ferrite core. Refer to "3.2.8 Attaching a
Ferrite Core".
For programming instructions and other information about the IP-GW16 card, refer to the
documentation for the IP-GW16 card. To program the IP-GW16 card, use the web programming
designed for the IP-GW16 card.
To confirm the CO line connection, refer to "Confirming the CO Line Connection" in "3.14.1 Starting
the PBX".
Pin Assignments
RJ45 Connector (10BASE-T/100BASE-TX)
94
Installation Manual
No.
Signal Name
Input (I)/Output (O)
Function
TPO+
Transmit data+
TPO-
Transmit data-
TPI+
Receive data+
4-5
Reserved
–
–
TPI-
Receive data-
7-8
Reserved
–
–
3.5 Information about the Physical Trunk Cards
LED Indications
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
ONLINE
Green
On-line status indication
•
ON: On-line mode
•
OFF: Off-line mode
•
Flashing: Maintenance mode
Note
If the LINK indicator is OFF, the ONLINE indicator will also be
OFF.
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm
VoIP BUSY
Green
VoIP (H.323) process indication
•
OFF: VoIP process inactive
•
ON: VoIP process active
LINK
Green
Link status indication
•
OFF: Connection error
•
ON: Normal connection
DATA
Green
Data transmission indication
•
OFF: No data transmitted
•
ON: Data transmitting
Installation Manual
95
3.6 Information about the Physical Extension Cards
3.6
Information about the Physical Extension
Cards
3.6.1
CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144)
Function
CSIF4: 4-port CS interface card for 4 CSs.
CSIF8: 8-port CS interface card for 8 CSs.
LED
RJ45
(LINE 1 to LINE 8)
To CS
Accessories and User-supplied Items
Accessories (included): none
User-supplied (not included): RJ45 connector
CAUTION
Make sure that the status of all the CSs connected to the CSIF cards are set to in-service (INS). For
information about how to view CS information using the KX-TDE Maintenance Console, refer to "2.5.14
Utility—CS Information" in the PC Programming Manual. If there is a CS in out-of-service (OUS) status,
make sure that it is securely connected to the CSIF card. If the CS remains in OUS status, there may
be a fault with the connection. Do not leave the connected CS in OUS status since it may cause severe
damage to the CSIF card.
Notes
•
•
•
96
LINE 5 to LINE 8 are for CSIF8 card only.
When using the CSIF4 card, please note that the PBX software will recognise the CSIF4 card as
the CSIF8 card. As a result, 8 cell stations may appear to be available; however, only 4 cell stations
are supported by the CSIF4 card.
For details about connecting the CS, refer to "3.9.7 Connecting a Cell Station to the PBX" in "3.9
Connection of 2.4 GHz Portable Stations".
Installation Manual
3.6 Information about the Physical Extension Cards
Editing the CS Name using the KX-TDE Maintenance Console
While programming the PBX, we strongly recommend that you input a unique recognizable CS name
(maximum 20 characters) for each CS port in use, and "(Reserved)" or "(Not for CSIF4)" for unused ports
or unavailable ports respectively for the following reasons:
a. you will be able to easily distinguish installed CSs.
b. you will be able to know which CSIF card has been installed; CSIF4 or CSIF8.
Example: When the CSIF4 card has been installed*1
Pin Assignments
RJ45 Connector
*1
No.
Signal Name
Function
1-2
Reserved
–
D1
Data port (High)
POWH
Power (High)
POWL
Power (Low)
D2
Data port (Low)
7-8
Reserved
–
The contents and design of the software are subject to change without notice.
Installation Manual
97
3.6 Information about the Physical Extension Cards
LED Indications
98
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
3.6 Information about the Physical Extension Cards
3.6.2
DHLC8 Card (KX-TDA0170)
Function
8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs (Basic/Highdensity), with 2 power failure transfer (PFT) ports.
LED
Amphenol
To extensions
Accessories and User-supplied Items
Accessories (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
•
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector".
For details about power failure transfer, refer to "3.13.1 Power Failure Connections".
Installation Manual
99
3.6 Information about the Physical Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
No. Signal Name Function
No. Signal Name Function
RA
SLT Ring port 1
26
TA
SLT Tip port 1
D2A
PT Data port 1 (Low)
27
D1A
PT Data port 1 (High)
Reserved
–
28
Reserved
–
RB
SLT Ring port 2
29
TB
SLT Tip port 2
D2B
PT Data port 2 (Low)
30
D1B
PT Data port 2 (High)
Reserved
–
31
Reserved
–
RC
SLT Ring port 3
32
TC
SLT Tip port 3
D2C
PT Data port 3 (Low)
33
D1C
PT Data port 3 (High)
Reserved
–
34
Reserved
–
10
RD
SLT Ring port 4
35
TD
SLT Tip port 4
11
D2D
PT Data port 4 (Low)
36
D1D
PT Data port 4 (High)
12
Reserved
–
37
Reserved
–
13
RE
SLT Ring port 5
38
TE
SLT Tip port 5
14
D2E
PT Data port 5 (Low)
39
D1E
PT Data port 5 (High)
15
Reserved
–
40
Reserved
–
16
RF
SLT Ring port 6
41
TF
SLT Tip port 6
17
D2F
PT Data port 6 (Low)
42
D1F
PT Data port 6 (High)
18
Reserved
–
43
Reserved
–
19
RG
SLT Ring port 7
44
TG
SLT Tip port 7
20
D2G
PT Data port 7 (Low)
45
D1G
PT Data port 7 (High)
21
Reserved
–
46
Reserved
–
22
RH
SLT Ring port 8
47
TH
SLT Tip port 8
23
D2H
PT Data port 8 (Low)
48
D1H
PT Data port 8 (High)
–
49- Reserved
50
24- Reserved
25
100
Installation Manual
–
3.6 Information about the Physical Extension Cards
LED Indications
Indication
Color
Description
CARD STATUS
Green/
Orange/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Orange Flashing: Detection of PT-interface CS connection (when
starting up the PT-interface CS [Basic/High-density])
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
101
3.6 Information about the Physical Extension Cards
3.6.3
DLC8 Card (KX-TDA0171)
Function
8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-density).
LED
Amphenol
To extensions
Accessories and User-supplied Items
Accessories (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
102
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector".
Installation Manual
3.6 Information about the Physical Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
No.
Signal Name Function
No.
Signal Name Function
Reserved
–
26
Reserved
–
D2A
Data port 1 (Low)
27
D1A
Data port 1 (High)
3-4
Reserved
–
28-29
Reserved
–
D2B
Data port 2 (Low)
30
D1B
Data port 2 (High)
6-7
Reserved
–
31-32
Reserved
–
D2C
Data port 3 (Low)
33
D1C
Data port 3 (High)
9-10
Reserved
–
34-35
Reserved
–
11
D2D
Data port 4 (Low)
36
D1D
Data port 4 (High)
12-13
Reserved
–
37-38
Reserved
–
14
D2E
Data port 5 (Low)
39
D1E
Data port 5 (High)
15-16
Reserved
–
40-41
Reserved
–
17
D2F
Data port 6 (Low)
42
D1F
Data port 6 (High)
18-19
Reserved
–
43-44
Reserved
–
20
D2G
Data port 7 (Low)
45
D1G
Data port 7 (High)
21-22
Reserved
–
46-47
Reserved
–
23
D2H
Data port 8 (Low)
48
D1H
Data port 8 (High)
24-25
Reserved
–
49-50
Reserved
–
LED Indications
Indication
Color
Description
CARD STATUS
Green/
Orange/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Orange Flashing: Detection of PT-interface CS connection (when
starting up the PT-interface CS [Basic/High-density])
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
103
3.6 Information about the Physical Extension Cards
3.6.4
DLC16 Card (KX-TDA0172)
Function
16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs (Basic/High-density).
LED
Amphenol
To extensions
Accessories and User-supplied Items
Accessories (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
104
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector".
Installation Manual
3.6 Information about the Physical Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
No.
Signal Name Function
No.
Signal Name Function
D2A
Data port 1 (Low)
26
D1A
Data port 1 (High)
D2B
Data port 2 (Low)
27
D1B
Data port 2 (High)
D2C
Data port 3 (Low)
28
D1C
Data port 3 (High)
D2D
Data port 4 (Low)
29
D1D
Data port 4 (High)
D2E
Data port 5 (Low)
30
D1E
Data port 5 (High)
D2F
Data port 6 (Low)
31
D1F
Data port 6 (High)
D2G
Data port 7 (Low)
32
D1G
Data port 7 (High)
D2H
Data port 8 (Low)
33
D1H
Data port 8 (High)
D2I
Data port 9 (Low)
34
D1I
Data port 9 (High)
10
D2J
Data port 10 (Low)
35
D1J
Data port 10 (High)
11
D2K
Data port 11 (Low)
36
D1K
Data port 11 (High)
12
D2L
Data port 12 (Low)
37
D1L
Data port 12 (High)
13
D2M
Data port 13 (Low)
38
D1M
Data port 13 (High)
14
D2N
Data port 14 (Low)
39
D1N
Data port 14 (High)
15
D2O
Data port 15 (Low)
40
D1O
Data port 15 (High)
16
D2P
Data port 16 (Low)
41
D1P
Data port 16 (High)
17-25
Reserved
–
42-50
Reserved
–
LED Indications
Indication
Color
Description
CARD STATUS
Green/
Orange/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Orange Flashing: Detection of PT-interface CS connection (when
starting up the PT-interface CS [Basic/High-density])
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
105
3.6 Information about the Physical Extension Cards
3.6.5
SLC8 Card (KX-TDA0173)
Function
8-port extension card for SLTs with 2 power failure transfer (PFT) ports.
LED
Amphenol
To extensions
Accessories and User-supplied Items
Accessories (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
•
106
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector".
For details about power failure transfer, refer to "3.13.1 Power Failure Connections".
Installation Manual
3.6 Information about the Physical Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
No.
Signal Name Function
No.
Signal Name Function
RA
Ring port 1
26
TA
Tip port 1
2-3
Reserved
–
27-28
Reserved
–
RB
Ring port 2
29
TB
Tip port 2
5-6
Reserved
–
30-31
Reserved
–
RC
Ring port 3
32
TC
Tip port 3
8-9
Reserved
–
33-34
Reserved
–
10
RD
Ring port 4
35
TD
Tip port 4
11-12
Reserved
–
36-37
Reserved
–
13
RE
Ring port 5
38
TE
Tip port 5
14-15
Reserved
–
39-40
Reserved
–
16
RF
Ring port 6
41
TF
Tip port 6
17-18
Reserved
–
43-44
Reserved
–
19
RG
Ring port 7
44
TG
Tip port 7
20-21
Reserved
–
45-46
Reserved
–
22
RH
Ring port 8
47
TH
Tip port 8
23-25
Reserved
–
48-50
Reserved
–
LED Indications
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
107
3.6 Information about the Physical Extension Cards
3.6.6
EXT-CID Card (KX-TDA0168)
Function
Sends Caller ID signals to extension ports. To be mounted on the SLC8 card only.
inside
SLC8 Card
Screw
EXT-CID Card
Accessories and User-supplied Items
Accessories (included): Screws × 2
User-supplied (not included): none
108
Installation Manual
3.6 Information about the Physical Extension Cards
3.6.7
SLC16 Card (KX-TDA0174) and MSLC16 Card (KXTDA0175)
Function
SLC16:
MSLC16:
16-port extension card for SLTs with 4 power failure transfer (PFT) ports.
16-port extension card for SLTs with Message Waiting Lamp control and 4 power failure
transfer (PFT) ports. Maximum power output of 160 V/90 V for Message Waiting Lamp
control.
LED
Amphenol
To extensions
Accessories and User-supplied Items
Accessories (included): Screws × 2, Ferrite core × 1
User-supplied (not included): Amphenol connector
Notes
•
•
•
•
Panasonic SLT with Message Waiting Lamp (e.g., KX-T7310) is recommended for connection to
the MSLC16 card.
Attach the included ferrite core to the cable. Refer to "3.2.8 Attaching a Ferrite Core".
To connect the Amphenol connector, refer to "3.2.9 Fastening an Amphenol Connector".
For details about power failure transfer, refer to "3.13.1 Power Failure Connections".
Installation Manual
109
3.6 Information about the Physical Extension Cards
Pin Assignments
Amphenol Connector
50
26
25
No.
Signal Name Function
No.
Signal Name Function
RA
Ring port 1
26
TA
Tip port 1
RB
Ring port 2
27
TB
Tip port 2
RC
Ring port 3
28
TC
Tip port 3
RD
Ring port 4
29
TD
Tip port 4
RE
Ring port 5
30
TE
Tip port 5
RF
Ring port 6
31
TF
Tip port 6
RG
Ring port 7
32
TG
Tip port 7
RH
Ring port 8
33
TH
Tip port 8
RI
Ring port 9
34
TI
Tip port 9
10
RJ
Ring port 10
35
TJ
Tip port 10
11
RK
Ring port 11
36
TK
Tip port 11
12
RL
Ring port 12
37
TL
Tip port 12
13
RM
Ring port 13
38
TM
Tip port 13
14
RN
Ring port 14
39
TN
Tip port 14
15
RO
Ring port 15
40
TO
Tip port 15
16
RP
Ring port 16
41
TP
Tip port 16
17-25
Reserved
–
42-50
Reserved
–
LED Indications
110
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
3.6 Information about the Physical Extension Cards
3.6.8
IP-EXT16 Card (KX-TDA0470)
Function
16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729a and
G.711 CODEC methods.
LEDs
RJ45
(10BASE-T/100BASE-TX
Full Duplex)
To LAN
Accessories and User-supplied Items
Accessories (included): Ferrite core × 1
User-supplied (not included): RJ45 connector
Notes
•
•
The maximum length of the cable to be connected to this optional service card is 100 m (328 ft).
When connecting the RJ45 connector, attach the included ferrite core. Refer to "3.2.8 Attaching a
Ferrite Core".
Pin Assignments
RJ45 Connector (10BASE-T/100BASE-TX)
No.
Signal Name
Input (I)/Output (O)
Function
TPO+
Transmit data+
TPO-
Transmit data-
TPI+
Receive data+
4-5
Reserved
–
–
TPI-
Receive data-
7-8
Reserved
–
–
Installation Manual
111
3.6 Information about the Physical Extension Cards
LED Indications
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
ONLINE
Green
On-line status indication
•
ON: At least one port is in use (an IP-PT is connected)
•
OFF: No ports are in use (no IP-PTs are connected)
Note
If the LINK indicator is OFF, the ONLINE indicator will also be
OFF.
112
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm
VoIP BUSY
Green
Panasonic proprietary VoIP protocol process indication
•
OFF: VoIP process inactive
•
ON: VoIP process active
LINK
Green
Link status indication
•
OFF: Connection error
•
ON: Normal connection
DATA
Green
Data transmission indication
•
OFF: No data transmitted
•
ON: Data transmitting
Installation Manual
3.7 Information about the Other Physical Cards
3.7
Information about the Other Physical Cards
3.7.1
OPB3 Card (KX-TDA0190)
Function
Optional 3-slot base card for mounting a maximum of 3 option cards from the following:
•
DPH4 card
•
EIO4 card
•
ECHO16 card
•
MSG4 card
LED
Accessories and User-supplied Items
Accessories (included): none
User-supplied (not included): none
WARNING
A LITHIUM BATTERY IS USED IN OPB3 CARD. THERE IS A RISK OF EXPLOSION IF THE
BATTERY IS REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
LED Indications
Indication
Color
Description
CARD STATUS
Green/Red
Card status indication
•
OFF: Power Off
•
Green ON: Normal (all ports are idle)
•
Green Flashing (60 times per minute): Normal (a port is in use)
•
Red ON: Fault (includes reset)
•
Red Flashing (60 times per minute): Out of Service
Installation Manual
113
3.7 Information about the Other Physical Cards
3.7.2
DPH4 Card (KX-TDA0161)
Function
4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card.
Fully insert the connectors through
the panel openings.
OPB3 Card
DPH4 Card
8-pin
Screw
To doorphones
To door openers
10-pin
Accessories and User-supplied Items
Accessories (included): Screws × 3, 10-pin terminal block × 1, 8-pin terminal block × 1
User-supplied (not included): Copper wire
Note
For details about connection to doorphones and door openers, refer to "3.10.1 Connection of
Doorphones, Door Openers, External Sensors, and External Relays".
114
Installation Manual
3.7 Information about the Other Physical Cards
Pin Assignments
8-pin Terminal Block
No.
Signal Name
Function
DP4
Doorphone 4 transmit
com4
Doorphone 4 receive
DP3
Doorphone 3 transmit
com3
Doorphone 3 receive
DP2
Doorphone 2 transmit
com2
Doorphone 2 receive
DP1
Doorphone 1 transmit
com1
Doorphone 1 receive
No.
Signal Name
Function
1-2
Reserved
–
OP4b
Door opener 4
OP4a
Door opener 4 com
OP3b
Door opener 3
OP3a
Door opener 3 com
OP2b
Door opener 2
OP2a
Door opener 2 com
OP1b
Door opener 1
10
OP1a
Door opener 1 com
10-pin Terminal Block
10
Installation Manual
115
3.7 Information about the Other Physical Cards
3.7.3
EIO4 Card (KX-TDA0164)
Function
4-port external input/output card. To be mounted on the OPB3 card.
Fully insert the connectors through
the panel openings.
OPB3 Card
EIO4 Card
8-pin
Screw
To external sensors
To external relays
10-pin
Accessories and User-supplied Items
Accessories (included): Screws × 3, 10-pin terminal block × 1, 8-pin terminal block × 1
User-supplied (not included): Copper wire
Note
For details about connection to external sensors and external relays, refer to "3.10.1 Connection of
Doorphones, Door Openers, External Sensors, and External Relays".
116
Installation Manual
3.7 Information about the Other Physical Cards
Pin Assignments
8-pin Terminal Block
No.
Signal Name
Function
C4b
Control 4
C4a
Control 4 com
C3b
Control 3
C3a
Control 3 com
C2b
Control 2
C2a
Control 2 com
C1b
Control 1
C1a
Control 1 com
No.
Signal Name
Function
1-2
Reserved
–
OP4b
Opener 4
OP4a
Opener 4 com
OP3b
Opener 3
OP3a
Opener 3 com
OP2b
Opener 2
OP2a
Opener 2 com
OP1b
Opener 1
10
OP1a
Opener 1 com
10-pin Terminal Block
10
Installation Manual
117
3.7 Information about the Other Physical Cards
External Sensor
Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card
as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card
for each external sensor. The PBX detects input from the sensor when the signal is under 100 Ω.
Connection Diagram
PBX
OPB3
EIO4
+5V
33
10K
I/O
4.7K
External Sensor
+5V
sensor
33
common
4.7K
External Relay
Current Limit: 24 V DC/30 V AC, 1 A maximum
118
Installation Manual
3.7 Information about the Other Physical Cards
3.7.4
ECHO16 Card (KX-TDA0166)
Function
16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card.
OPB3 Card
inside
ECHO16 Card
Screw
Accessories and User-supplied Items
Accessories (included): Screws × 3
User-supplied (not included): none
Note
To establish a conference call involving 6 to 8 parties, install an ECHO16 card and enable echo
cancellation for conferences using the KX-TDE Maintenance Console. For details, refer to "Echo
Cancel—Conference" in "2.8.18 [2-9] System Options" of the PC Programming Manual.
Installation Manual
119
3.7 Information about the Other Physical Cards
3.7.5
MSG4 Card (KX-TDA0191)
Function
4-channel message card. To be mounted on the OPB3 card.
OPB3 Card
inside
MSG4 Card
Screw
Accessories and User-supplied Items
Accessories (included): Screws × 3
User-supplied (not included): none
120
Installation Manual
3.8 Connection of Extensions
3.8
Connection of Extensions
3.8.1
Maximum Cabling Distances of the Extension Wiring
(Twisted Cable)
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
222 m (728 ft)
347 m (1138 ft)
500 m (1640 ft)
347 m (1138 ft)
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
500 m (1640 ft)
720 m (2362 ft)
830 m (2723 ft)
720 m (2362 ft)
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
140 m (459 ft)
229 m (751 ft)
360 m (1181 ft)
229 m (751 ft)
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
698 m (2289 ft)
1128 m (3700 ft)
1798 m (5897 ft)
1128 m (3700 ft)
PT-interface CS
(Basic/High-density)
KX-T7600 Series DPT*
Other PT (DPT/APT)
and DSS Console
SLT
* The maximum cabling distance from the PBX is the same even when the KX-T7600 series DPT is the
master DPT on the Digital XDP connection.
Notice
The maximum cabling distance may vary depending on the conditions.
Installation Manual
121
3.8 Connection of Extensions
PT-interface CS
(Basic/Highdensity)
DPT
APT
DHLC8 Card
MSLC16, SLC16,
SLC8 Cards
DLC16, DLC8 Cards
122
" indicates that the extension card supports the terminal.
Installation Manual
DSS Console
SLT
3.8 Connection of Extensions
3.8.2
Parallel Connection of the Extensions
Any SLT can be connected in parallel with an APT or a DPT as follows.
Note
In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in
parallel with an APT or a DPT.
With APT
For parallel connection, eXtra Device Port (XDP) mode must be disabled for that port through system
programming. Refer to "1.11.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the
Feature Manual for further information.
To DHLC8 card
Modular
T-Adaptor
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "T", "R", "D1",
and "D2".
APT
SLT
Installation Manual
123
3.8 Connection of Extensions
With DPT
Parallel mode or eXtra Device Port (XDP) mode can be selected through system programming.
If XDP mode is enabled through system programming, parallel connection is not possible. Refer to "1.11.9
Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Manual for further
information.
Using a Modular T-Adaptor
To DHLC8 card
Modular
T-Adaptor
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "D1" and
"D2".
DPT
SLT
Using an EXtra Device Port
With KX-T7600 Series DPT (except KX-T7665)
To DHLC8 card
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
DPT
SLT
TO MAIN UNIT TO TEL
/ PABX
To DHLC8 card
To SLT
124
Installation Manual
3.8 Connection of Extensions
With Other DPT
To DHLC8 card
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
DPT
SLT
TO TEL
TO EMSS or TO MAIN UNIT
To DHLC8 card
To SLT
Installation Manual
125
3.8 Connection of Extensions
3.8.3
Digital EXtra Device Port (Digital XDP) Connection
A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected
to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode.
Notes
•
•
•
Both DPTs must be KX-T7600 series DPTs (except KX-T7640). Note that the KX-T7667 can only
be connected as a slave DPT.
Parallel mode or XDP mode can be selected through system programming.
If XDP mode is enabled through system programming, parallel connection is not possible. Refer to
"1.11.9 Parallelled Telephone" and "2.1.1 Extension Port Configuration" in the Feature Manual for
further information.
With KX-T7600 Series DPT
Using a Modular T-Adaptor
To DLC8/DLC16 card
Modular
T-Adaptor
To DHLC8 card
(for connection of SLT)
2-conductor wiring cord
Connect pins "T" and "R".
4-conductor wiring cord
Connect pins "D1" and "D2".
4-conductor wiring cord
Connect pins "D1" and
"D2".
SLT
Master DPT
Slave DPT
Back View of DPTs
TO TEL
TO MAIN UNIT
/ PABX
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
TO MAIN UNIT
/ PABX
Maximum Distance
30 m (98 ft)
50 m (164 ft)
60 m (196 ft)
50 m (164 ft)
Master DPT
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
126
Installation Manual
Slave DPT
3.8 Connection of Extensions
Using an EXtra Device Port
To DLC8/DLC16 card
To DHLC8 card
(for connection of SLT)
4-conductor wiring cord
Connect pins "T", "R",
"D1" and "D2".
4-conductor wiring cord
Connect pins "T", "R", 2-conductor wiring cord
"D1" and "D2".
Connect pins "T" and "R".
Master DPT
Slave DPT
SLT
Back View of DPTs
TO MAIN UNIT
/ PABX
TO TEL
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
TO MAIN UNIT
/ PABX
Maximum Distance
30 m (98 ft)
50 m (164 ft)
60 m (196 ft)
50 m (164 ft)
TO TEL
Master DPT
To DLC8/DLC16 card
Slave DPT
To SLT
To DHLC8 card
(for connection of SLT)
Installation Manual
127
3.8 Connection of Extensions
3.8.4
First Party Call Control CTI Connection
CTI connection between a PC and a KX-T7633/T7636 DPT provides first party call control. The CTI
connection is made via a USB interface (version 2.0), and uses the TAPI 2.1 protocol.
A USB Module (KX-T7601) must be connected to the KX-T7633/T7636 DPT.
Note
The operating system of the PC required for first party call control depends on your CTI application
software. For details, refer to the manual for your CTI application software.
To PC
USB Port
UL
USB Cable
USB Module
Notes
•
•
128
The maximum length of the USB cable is 3 m (9 ft 10 in).
USB Modules must not be connected to DPTs in the Digital XDP connection. In a Digital XDP
connection, the PC cannot be used. If a USB module is connected to a slave DPT, the DPT will not
work properly.
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
3.9
Connection of 2.4 GHz Portable Stations
3.9.1
Overview
Radio Methods
There are new and old radio methods for the 2.4 GHz wireless system. The radio method can be selected
through system programming. Make sure that all CSs on a wireless system have the same radio method.
Required Equipment and Maximum Number of Calls
CSs determine the area covered by the wireless system. The number of calls that can be made
simultaneously through each CS varies depending on the model and radio method, as follows:
Radio Method
New
Old
CS
Connection Card
Maximum Calls
KX-T0151
DHLC/DLC
KX-TDA0152
CSIF
KX-TDA0158
DHLC/DLC
KX-T0151
DHLC/DLC
KX-TDA0152
CSIF
KX-T0141
DHLC/DLC
KX-TDA0142
CSIF
Compatible PSs
•
•
KX-TD7685
KX-TD7695
•
•
•
•
KX-TD7684
KX-TD7694
KX-TD7680
KX-TD7690
Note
For more details about the PS, refer to the Operating Instructions of the PS.
CAUTION
•
•
•
•
•
•
The CS should be kept free of dust, moisture, high temperature (more than 40 ˚C), low temperature
(less than 0 ˚C), and vibration, and should not be exposed to direct sunlight.
The CS should not be placed outdoors (use indoors).
The CS should not be placed near high-voltage equipment.
The CS should not be placed on a metal object.
Systems using 2.4 GHz ISM (Industrial, Scientific and Medical) band may interfere with the KXTDA wireless system. Examples of such systems are cordless telephones, wireless LAN, Home
RF, microwave ovens and other ISM devices. These systems may cause minor noise.
Keeping some distance between the equipment listed below may prevent interference. (The
distance may vary depending on the environment.)
Equipment
Distance
CS and office equipment such as a computer, telex, fax
machine, etc.
More than 2 m (6 ft 7 in)
CS and PS
More than (3 ft 3 in)
Each PS
More than 0.5 m (1 ft 8 in)
PBX and CS
More than 2 m (6 ft 7 in)
Installation Manual
129
3.9 Connection of 2.4 GHz Portable Stations
Equipment
Distance
CS and CS
More than 15 m (49 ft)
Please take into consideration the distance between the CSs when site planning. Please consult
a certified dealer for details.
However, the required distance between CSs may vary depending on the environment of the
installation site and conditions in which the wireless system is used. Conduct the site survey to
determine the appropriate distance.
130
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
3.9.2
Procedure Overview
When connecting the wireless system, use extreme care in conducting the site survey. An incorrectly
performed site survey can result in poor service area, frequent noise, and disconnection of calls.
1. Investigate the installation site
Refer to "3.9.3 Site Planning".
a. Obtain a map of the CS installation site.
b. Identify the service area required by the user on the map.
c. Plan the location of each CS, taking account of distance, building materials, etc.
2. Prepare the CS for site survey
Refer to "3.9.4 Before Site Survey".
a. Assign a CS number to each CS by setting the DIP switches on the back of the CS.
b. Supply electricity to each CS using an AC adaptor or a battery box.
c. Install each CS temporarily as planned.
Notes
•
•
Install at least 2 m (6 ft 7 in) above the floor.
Keep the antennas in the upright position.
3. Conduct the site survey
Refer to "3.9.5 Site Survey".
a. Test the radio signal strength using the PS.
Confirm that the radio signal strength level is "12" near the CS.
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
Display example:
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
CS NO.1 LEVEL:12
<< SEARCHING >>
SAVE:0123456789
1 to 9
Using the KX-TD7680
Display example:
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
CS NO.1 LEVEL:12
<< SEARCHING >>
SAVE:0123456789
1 to 9
Using the KX-TD7690
Display example:
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
1 to 9
CS NO.1 LEVEL:12
<< SEARCHING >>
SAVE:0123456789
b. By walking away from the CS with the PS, check the radio signal strength. The radio signal strength
weakens as you walk away from the CS.
c. Map the CS coverage area at radio signal strength levels "3" and "8".
Installation Manual
131
3.9 Connection of 2.4 GHz Portable Stations
d. Make sure that adjacent CS coverage areas overlap where the radio signal strength level is "8" by
at least 5 m (16 ft).
e. Make sure that the radio signal strength level is greater than "3" at any location within the service
area required by the user.
4. Finish the site survey
Refer to "3.9.6 After Site Survey".
a. Return all DIP switches of each CS to the OFF position, and stop supplying power.
b. Turn off the PS.
5. Connect the CS and PS to the PBX and test the operation
Refer to "3.9.7 Connecting a Cell Station to the PBX".
a. Connect the CSs to the PBX.
b. Register the PSs to the PBX.
c. Walk around the service area while having a conversation using a registered PS. If noise is
frequent or conversations disconnect, relocate the CSs or install an additional CS.
6. Mount the CS on the wall
Refer to "3.9.8 Wall Mounting".
a. If there are no problems in testing, mount the CS on the wall.
132
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
3.9.3
Site Planning
Choosing the best site for the CS requires careful planning and testing of essential areas. The best location
may not always be convenient for installation. Read the following information before installing the unit.
Understanding Radio Waves
Characteristics of Radio Waves
The transmission of radio waves and the CS coverage area depend on the structure and materials of the
building.
Office equipment, such as computers and fax machines, can interfere with radio waves. Such equipment
may create noise or interfere with the performance of the PS.
The illustration below shows the special transmitting patterns of radio waves.
1. Radio waves are reflected by objects made of materials such as metal.
2. Radio waves are diffracted by objects such as metallic columns.
3. Radio waves penetrate objects made of materials such as glass.
CS
1. Reflection
Column
2. Diffraction
3. Penetration
Relationships Between Radio Waves and Building Structure and Materials
•
•
•
•
•
The CS coverage area is affected more by the building materials and their thickness than the number
of obstacles.
Radio waves tend to be reflected or diffracted by conductive objects and rarely penetrate them.
Radio waves tend to penetrate insulated objects and are rarely reflected by them.
Radio waves penetrate thin objects more than thick objects.
The table below shows the transmission tendency of radio waves when they reach objects made from
various materials.
Installation Manual
133
3.9 Connection of 2.4 GHz Portable Stations
Object
Material
Transmission Tendency
Wall
Concrete
The thicker they are, the less radio waves
penetrate them.
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves are reflected.
Glass
Radio waves usually penetrate them.
Glass with wire net
Radio waves can penetrate them, but tend to be
reflected.
Window
Glass covered with heat- Radio waves are weakened considerably when
resistant film
they penetrate windows.
Floor
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves are reflected.
Partition
Steel
Radio waves are reflected and rarely penetrate
them.
Plywood, Glass
Radio waves usually penetrate them.
Ferroconcrete
Radio waves can penetrate them, but the more iron
there is, the more radio waves tend to be reflected
or diffracted.
Metal
Radio waves tend to be reflected or diffracted.
Steel
Radio waves are usually reflected or diffracted,
and rarely penetrate them.
Wood
Radio waves can penetrate them, but they are
weakened.
Column
Cabinet
134
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
CS Coverage Area
The example below shows the size of the coverage area of 1 CS if it is installed in an area with no obstacles.
Note
Radio signal strength levels are measured during the site survey (refer to "3.9.5 Site Survey").
Coverage Area
Radio signal strength level is
greater than "3".
(About 50 m to 60 m
[164 ft to 197 ft])
Gray Zone:
Conversation will be
intermittent
Good Coverage Area
Radio signal strength
level is greater than "8".
(About 30 m to 40 m
[98 ft to 131 ft])
Good sound quality
can be maintained.
Out of Service:
Cannot make/receive calls
Radio Signal Strength Levels
Level: 00
Level: 01 to 02
Level: 03 to 07
Level: 08 to 10
Level: 11 to 12
Out of range
Receives noise easily or disconnects
May receive noise
Good
Better
Site Survey Preparation
1. Obtain a map and investigate the installation site.
a. Check the obstacles (e.g., shelves, columns, and partitions).
b. Check the materials of the structures (e.g., metal, concrete, and plywood).
c. Check the layout and dimensions of the room, corridor, etc.
d. Write down the above information on the map.
2. Examine the service area required by the user on the map, referring to the following example.
a. Draw the coverage area around a CS. Extend the coverage area 30 to 60 meters (98 to 197 feet)
in each direction, depending on the materials of the building structures and obstacles in the
installation site. Note that a CS cannot be installed outside a building.
b. If one CS cannot cover the entire service area, install additional CSs as required. Overlap the
coverage areas of adjacent CSs.
Where CS coverage areas overlap, the PS will start call handover to the next CS if the signal from
Installation Manual
135
3.9 Connection of 2.4 GHz Portable Stations
one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available
for handover, the PS may go out of range and the call could be lost.
If the signal from the CS fades, due to the structure of the building, there may be some handover
delay. The user will hear a range warning before handover in this case. This also applies in the case
of interference from 2.4 GHz apparatus.
Example: Installing in a Room Separated by Interior Walls
Things to take note of:
•
The room is separated by interior walls.
•
The room is surrounded by concrete walls.
CS installation plan:
•
The coverage area of each CS will not extend as far as when there are no obstacles, because the
radio signals will be weakened by separating walls. Therefore, you will need 5 CSs to cover the
entire room.
150 m (492 ft)
70 m
(230 ft)
CS no. 1
CS no. 2
CS no. 5
CS no. 3
136
Installation Manual
CS no. 4
3.9 Connection of 2.4 GHz Portable Stations
3.9.4
Before Site Survey
Setting and Installing the CS Temporarily for Site Survey
1. Switch the Radio Signal Test switch from OFF to ON.
2. Set the CS number switches as desired.
KX-T0151/KX-TDA0152
CS no. 1
CS no. 2
CS no. 3
CS no. 4
CS no. 5
CS no. 6
ON
DIP Switch
CS no. 7
OFF
CS Number Switch
Keep this switch at the default
"OFF" position. Otherwise, the
CS will not function.
Radio Signal
Test Switch
CS no. 8
CS no. 9
Installation Manual
137
3.9 Connection of 2.4 GHz Portable Stations
KX-TDA0158
OFF
ON
Radio Signal
Test Switch
Keep this switch at the default
"OFF" position. Otherwise, the
CS will not function.
CS Number Switch
DIP Switch
CS no. 1
138
CS no. 2
CS no. 3
CS no. 4
CS no. 5
CS no. 6
CS no. 7
CS no. 8
CS no. 9
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
KX-T0141/KX-TDA0142
DIP Switch
OFF
ON
CS Number Switch
Keep this switch at the default
"OFF" position. Otherwise, the
CS will not function.
CS no. 1
CS no. 2
CS no. 3
CS no. 4
Radio Signal
Test Switch
CS no. 5
CS no. 6
CS no. 7
CS no. 8
CS no. 9
Note
If more than 1 CS is in Radio Signal Test mode, each CS must have a unique CS number.
Installation Manual
139
3.9 Connection of 2.4 GHz Portable Stations
3. After setting the DIP switch, connect an AC adaptor or battery box to the CS using a power supply
adaptor.
Note
The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect
the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become
disconnected.
KX-T0151/KX-TDA0152
KX-TDA0158
KX-T0141/KX-TDA0142
Modular
Modular
Telephone Cord
Telephone Cord
(PSJA1017Z)
Telephone Cord
Power Supply Adaptor
(PSZZ1TDA0142)
Power Supply Adaptor
(PSZZ1TDA0142)
Power Supply Adaptor
(PSZZ1TDA0142)
To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE)
To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE)
Modular
To AC Adaptor (KX-A11/KX-TCA1)/
Battery Box (PSZZTD142CE)
4. Install the CS temporarily for the site survey. Install the CS at least 2 m (6 ft 7 in) above the floor, keeping
the antennas in the upright position.
140
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
3.9.5
Site Survey
The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS. After installing the
CSs temporarily, set the PS to Radio Signal Test mode and measure each CS coverage area. Then, record
the results on the map of the installation site.
Testing the Radio Signal Strength
Note
Display prompts for the site survey are only available in English.
1. Enter Radio Signal Test mode.
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
Display example:
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
CS NO.1 LEVEL:12*1
<< SEARCHING >>
1 to 9
SAVE:0123456789*2
To store the scan data
Scan Data No.
0 to 9
Using the KX-TD7680
Display example:
CS No.
CS NO.1 LEVEL:12*1
<< SEARCHING >>
1 to 9
Press 1, 9, and POWER
for more than 2 seconds.
SAVE:0123456789*2
To store the scan data
Scan Data No.
0 to 9
Using the KX-TD7690
Display example:
Press 1, 9, and POWER
for more than 2 seconds.
CS No.
1 to 9
CS NO.1 LEVEL:12*1
<< SEARCHING >>
SAVE:0123456789*2
To store the scan data
Scan Data No.
0 to 9
Notes
*1: CS number and radio signal strength level.
*2: Scan data (test result) number. Empty memory space will be indicated by a number; stored memory
space will be indicated by a "-".
Installation Manual
141
3.9 Connection of 2.4 GHz Portable Stations
2. Measure the radio signal strength by moving towards and away from the CS.
a. Move to the CS until the radio signal strength level becomes "12".
b. Move away from the CS and identify the CS coverage area within which the radio signal strength
level is greater than "8". Draw the area on the map.
c. Move away from the CS and identify the CS coverage area within which the radio signal strength
level is greater than "3". Draw the area on the map.
PS
CS NO.1 LEVEL:12
CS no. 1
PS
CS NO.1 LEVEL:8
PS
CS NO.1 LEVEL:3
Radio Signal Strength Levels
Level: 00
Level: 01 to 02
Level: 03 to 07
Level: 08 to 10
Level: 11 to 12
Out of range
Receives noise easily or disconnects
May receive noise
Good
Better
3. Repeat steps 1 and 2 for other CSs, and relocate the CSs when necessary.
a. Overlap adjacent CS coverage areas where the radio signal strength level is "8" by 5 to 10 meters
(16 to 33 feet).
CS no. 1
CS no. 2
5 m to 10 m
(16 ft to 33 ft)
142
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
b. Overlap the CS coverage areas of at least 2 CSs at any location in the installation site.
CS no. 1
CS no. 2
CS no. 3
CS no. 4
c. Make sure that the radio signal strength level is greater than "3" at any location in the service area
required by the user.
Referring to the Stored Scan Data
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
Press 1, 9, and POWER
for more than 2 seconds.
Scan Data No.
0 to 9
Display example:
When there is scan data
NO.1
CS No.2 LEVEL: 9
When there is no scan data
NO.0
NOT SAVED
To the Desired Scan Data No.
Using the KX-TD7680
Press 1, 9, and POWER
for more than 2 seconds.
Scan Data No.
0 to 9
Display example:
When there is scan data
NO.1
CS No.2 LEVEL: 9
When there is no scan data
NO.0
NOT SAVED
To the Desired Scan Data No.
Installation Manual
143
3.9 Connection of 2.4 GHz Portable Stations
Using the KX-TD7690
Scan Data No.
0 to 9
Press 1, 9, and POWER
for more than 2 seconds.
Display example:
When there is scan data
NO.1
CS No.2 LEVEL: 9
When there is no scan data
NO.0
NOT SAVED
To the Desired Scan Data No.
Deleting the Stored Scan Data
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
Scan Data No.
0 to 9, or # for all data
Press 1, 9, and POWER
for more than 2 seconds.
To the Desired Scan Data No.
Using the KX-TD7680
Scan Data No.
0 to 9, or # for all data
Press 1, 9, and POWER
for more than 2 seconds.
To the Desired Scan Data No.
Using the KX-TD7690
Press 1, 9, and POWER
for more than 2 seconds.
Scan Data No.
0 to 9, or # for all data
To the Desired Scan Data No.
144
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
3.9.6
After Site Survey
After obtaining the proper measurement results, exit Radio Signal Test mode before connecting the CS to
the PBX.
1. Keep pressing the POWER button on the PS until the PS is turned OFF.
2. Disconnect the AC adaptor or battery box from the CS and stop supplying electricity.
KX-T0151/KX-TDA0152
KX-TDA0158
KX-T0141/KX-TDA0142
3. Switch all DIP switches on the CS from ON to OFF.
OFF
ON
Installation Manual
145
3.9 Connection of 2.4 GHz Portable Stations
3.9.7
Connecting a Cell Station to the PBX
Using a CSIF Card
Refer to the following example to connect a CS to the PBX.
KX-TDA0152/KX-TDA0142
CSIF8 Card
Port 1
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
444 m (1457 ft)
694 m (2277 ft)
1000 m (3281 ft)
694 m (2277 ft)
CSIF card (RJ45)
CS (RJ11)
Signal Name
D1
POWH
POWL
D2
Pin No.
Pin No.
Signal Name
D1
POWH
POWL
D2
Accessories and User-supplied Items for the CS
Accessories (included): Screws × 2, Washers × 2
User-supplied (not included): RJ11 connector
Note
For details about CSIF card, refer to "3.6.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KXTDA0144)".
146
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
Using a DHLC/DLC Card
Refer to the following example to connect a CS to the PBX.
KX-TDA0158
DHLC8 Card
Cable
26 AWG:
24 AWG:
22 AWG:
Maximum Distance
222 m (728 ft)
347 m (1138 ft)
500 m (1640 ft)
347 m (1138 ft)
CAT 5:
CS (RJ45)
Signal Name
D1C
D2C
D1B
D1A
D2A
D2B
Pin No.
Master
DHLC/DLC card (Amphenol)
Signal Name
D1C
D2C
D1D
D2D
D1E
D2E
Accessories and User-supplied Items for the CS
Accessories (included): Screws × 2, Washers × 2
User-supplied (not included): RJ45 connector
Notes
•
•
The no. 4 and no. 5 pins (Master) of the CS must be connected to a pair of pins on the DHLC/DLC
card. Then use 3 consecutive pairs of pins on the DHLC/DLC card, starting with the pins
corresponding to the Master, as in the example above.
CS connections must be made within the same DHLC/DLC card.
Installation Manual
147
3.9 Connection of 2.4 GHz Portable Stations
KX-T0151/KX-T0141
DHLC8 Card
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
222 m (728 ft)
347 m (1138 ft)
500 m (1640 ft)
347 m (1138 ft)
CS (RJ11)
Signal Name
D1
D2
Pin No.
DHLC/DLC card (Amphenol)
Signal Name
D1
D2
Accessories and User-supplied Items for the CS
Accessories (included): Screws × 2, Washers × 2
User-supplied (not included): RJ11 connector
Note
For details about DHLC card or DLC card, refer to "3.6.2 DHLC8 Card (KX-TDA0170)", "3.6.3 DLC8
Card (KX-TDA0171)", or "3.6.4 DLC16 Card (KX-TDA0172)".
148
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
Connecting the CS
1. Connect the cable from the CSIF/DHLC/DLC card to the CS.
KX-T0151/KX-TDA0152
Modular
To CSIF/DHLC/DLC card
KX-TDA0158
Modular
To DHLC/DLC card
KX-T0141/KX-TDA0142
Modular
To CSIF/DHLC/DLC card
2. Pass the cable through the groove of the CS (in any direction depending on your preference).
KX-T0151/KX-TDA0152
KX-TDA0158
KX-T0141/KX-TDA0142
To CSIF/DHLC/DLC card
To DHLC/DLC card
To CSIF/DHLC/DLC card
Installation Manual
149
3.9 Connection of 2.4 GHz Portable Stations
Registering the PS
The PS must be registered to the PBX before it can be used. Programming of both the PS and PBX is
required. A PT with multiline display (e.g., KX-T7636 6-line display) is required to perform the PBX system
programming.
Note
For details about system programming using a PT, refer to "2.3.2 PT Programming" in the Feature
Manual, and "2.1 PT Programming" in the PT Programming Manual.
Entering the System Programming Mode
PT (Administrator Level)
PROGRAM/
PAUSE
System Password for Administrator—
for PT Programming
Programming No.
= 1234
3 digits
PS (Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695)
Press POWER
for 2 seconds.
Select
"Setting Handset".
Select
"System Option".
If required
System Lock Password
System Setting Menu
4 digits
PS (Using the KX-TD7680)
FUNC
Press POWER
for 2 seconds.
Select
"PS PROGRAM".
Select
"SYSTEM SET".
If required
System Lock Password
System Setting Menu
4 digits
PS (Using the KX-TD7690)
MENU
Press POWER
for 2 seconds.
S1
SEL
Select
"PS PROGRAM".
If required
SEL
Select
"SYSTEM SETTING".
S1
ENTR
System Lock Password
4 digits
System Setting Menu
S1
Note
means default value throughout this section.
150
Installation Manual
S1
3.9 Connection of 2.4 GHz Portable Stations
PS Registration
[690]
ENTER
PS No.
Extn. No.
001 to 128
1 to 4 digits
To the PS
operation
below
ENTER
END
When the PS has not been registered yet
When registering the PS for the first time, it is possible to select the desired language for the display.
(You do not need to enter the PS system programming mode when registering for the first time.)
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
C.Tone
Press
POWER for
2 seconds.
C.Tone
Press "F"
for 2
seconds.
Select the desired
language.
Using the KX-TD7680
[ F2 ]
[ F3 ]
Press S2 repeatedly
to select the desired
language.
Press S3
for 2
seconds.
C.Tone
Press
POWER for
2 seconds.
Using the KX-TD7690
F2
F3
Press S2 repeatedly
to select the desired
language.
Press S3
for 2
seconds.
C.Tone
Press
POWER for
2 seconds.
When the PS has already been registered to another PBX
One PS can be registered to a maximum of 4 different PBXs.
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
C.Tone
Select
"Register H/set".
Choose
"Base 1–4".
Using the KX-TD7680
C.Tone
Choose
"SYSTEM 1–4".
Select
"REGISTRATION".
Using the KX-TD7690
SEL
Select
"REGISTRATION".
S1
SEL
Choose
"SYSTEM 1–4".
C.Tone
S1
Installation Manual
151
3.9 Connection of 2.4 GHz Portable Stations
Setting the System Lock
When a system lock has been set, the system lock password will be required for PS system setting.
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
Select
"SYSTEM LOCK".
Choose "On/Off".
System Lock Password
System Lock Password
4 digits
4 digits
On
Off
C.Tone
Using the KX-TD7680
Choose
"Enable/Disable".
Select
"SYSTEM LOCK".
System Lock Password
System Lock Password
4 digits
4 digits
ENABLE
DISABLE
C.Tone
Using the KX-TD7690
Select
"SYSTEM LOCK".
SEL
SEL
CHNG
S1
S1
Choose
"Enable/Disable".
System Lock Password
ENTR
System Lock Password
ENABLE
S1
DISABLE
ENTR
C.Tone
S1
152
Installation Manual
4 digits
S1
4 digits
3.9 Connection of 2.4 GHz Portable Stations
Setting the Personal Identification Number (PIN) for PS Registration
To prevent registering the PS to a wrong PBX, a PIN for PS registration can be set to the PBX. Before
registering the PS to the PBX, enter the PIN set to the PBX into the PS. By doing so, the PS will only be
registered to the PBX with the matching PIN.
Notes
•
By default, the PIN for PS registration is "1234" for both the PBX and PS. Therefore, the PS can
be registered to the PBX without setting the PIN.
•
The PIN for PS registration will only be used when registering the PS to the PBX. Therefore, during
normal operation after registration, even if there is more than 1 PBX with the same PIN near the
PS, the PS will not be inadvertently linked to a different PBX.
Setting the PIN for PBX
[692]
PIN for PS Registration
ENTER
4 digits
1234
ENTER
END
Setting the PIN for PS
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
PIN for PS Registration
Select
"Change PIN"
C.Tone
1 to 8 digits
1234
Using the KX-TD7680
PIN for PS Registration
Select
"CHANGE PIN"
C.Tone
1 to 4 digits
1234
Using the KX-TD7690
SEL
Select
"CHANGE PIN"
S1
PIN for PS Registration
1 to 4 digits
1234
ENTR
C.Tone
S1
Installation Manual
153
3.9 Connection of 2.4 GHz Portable Stations
PS Termination
Confirm the following before cancelling the PS registration:
•
The PS is turned on.
•
The PS is within range.
[691]
PS No.
001 to 128
ENTER
ENTER
If "Rejected" or "Time out" is displayed
CLEAR
Press "CLEAR".
YES
To the PS
operation
below
END
Press "YES".
If the registration information is still stored in the PS
Using the KX-TD7684/KX-TD7685/KX-TD7694/KX-TD7695
Select "Cancel Base".
Select "Base 1-4".
C.Tone
Select "YES".
Using the KX-TD7680
Select "YES".
Select the
desired item.
Select "DELETE
SYSTEM".
C.Tone
Using the KX-TD7690
SEL
Select "DELETE
SYSTEM".
S1
SEL
Select the
desired item.
S1
Select "YES".
SEL
C.Tone
S1
Testing the Operation
Walk around the service area while having a conversation using a registered PS. If noise is frequent or
conversations disconnect, relocate the CSs or install an additional CS.
154
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
3.9.8
Wall Mounting
Mounting the KX-T0151/KX-TDA0152/KX-TDA0158
1. Place the reference for wall mounting (KX-T0151/KX-TDA0152/KX-TDA0158) on the wall to mark the
2 screw positions.
2. Install the 2 screws and washers (included) into the wall.
Notes
•
•
Make sure that the screw heads are at the same distance from the wall.
Install the screws perpendicular to the wall.
3. Insert the upper and lower tabs of the wall mounting plate into the designated openings in the base unit.
KX-T0151/KX-TDA0152
KX-TDA0158
Tabs
Tabs
4. Slide the wall mounting plate in the direction of the arrow until it clicks.
KX-T0151/KX-TDA0152
KX-TDA0158
5. Hook the CS on the screw heads.
KX-T0151/KX-TDA0152
KX-TDA0158
83 mm
83 mm
Installation Manual
155
3.9 Connection of 2.4 GHz Portable Stations
Reference for Wall Mounting (KX-T0151/KX-TDA0152/KX-TDA0158)
Please copy this page and use as a reference for wall mounting.
Install a screw here.
83 mm
(3-1/4 in)
Install a screw here.
Note
Make sure to set the print size to correspond with the size of this page. If the dimension of the paper
output still deviates slightly from the measurement indicated here, use the measurement indicated
here.
156
Installation Manual
3.9 Connection of 2.4 GHz Portable Stations
Mounting the KX-T0141/KX-TDA0142
1. Place the reference for wall mounting (KX-T0141/KX-TDA0142) on the wall to mark the 2 screw
positions.
2. Install the 2 screws and washers (included) into the wall.
Notes
•
•
Make sure that the screw heads are at the same distance from the wall.
Install the screws perpendicular to the wall.
3. Hook the CS on the screw heads.
Installation Manual
157
3.9 Connection of 2.4 GHz Portable Stations
Reference for Wall Mounting (KX-T0141/KX-TDA0142)
Please copy this page and use as a reference for wall mounting.
Install a screw here.
71 mm
(2-13/16 in)
Install a screw here.
Note
Make sure to set the print size to correspond with the size of this page. If the dimension of the paper
output still deviates slightly from the measurement indicated here, use the measurement indicated
here.
158
Installation Manual
3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays
3.10 Connection of Doorphones, Door Openers,
External Sensors, and External Relays
3.10.1 Connection of Doorphones, Door Openers, External
Sensors, and External Relays
The PBX supports a maximum of 16 doorphones, 16 door openers, 16 external sensors, and 16 external
relays.
Note
Doorphones, door openers, external sensors, and external relays are user-supplied.
Maximum Cabling Distance
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
70 m (230 ft)
113 m (371 ft)
180 m (590 ft)
113 m (371 ft)
Doorphone
Door Opener
External Sensor/
External Relay Device
Installing the Doorphone (KX-T30865)
1. Loosen the screw to separate the doorphone into 2 halves.
Pan
ason
ic
Screw
Installation Manual
159
3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays
2. Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws.
Screw
To 8-pin terminal block
Note
Two kinds of screws are included with a KX-T30865. Please choose the appropriate kind for your wall
type.
: when a doorphone plate has been fixed to the wall
: when you wish to install the doorphone directly onto the wall
3. Connect the wires to the screws located in the front cover.
To 8-pin terminal block
4. Re-attach the 2 halves and re-insert the screw.
Connection
Use 8-pin and 10-pin terminal blocks (included with the card) for connection.
1. While pressing down on the hole at the top of the terminal block using a screwdriver, insert the wire into
the side hole as shown below. Repeat this procedure for other doorphones, door openers, external
sensors, and external relays.
Refer to "3.7.2 DPH4 Card (KX-TDA0161)" and "3.7.3 EIO4 Card (KX-TDA0164)" for pin assignments.
Doorphone
Door Opener
External Sensor/
External Relay Device
160
Installation Manual
3.10 Connection of Doorphones, Door Openers, External Sensors, and External Relays
2. Attach the terminal blocks to the connectors of the DPH4/EIO4 card on the PBX.
To doorphones/
door openers/
external sensors/
external relays
Installation Manual
161
3.11 Connection of Peripherals
3.11 Connection of Peripherals
3.11.1 Connection of Peripherals
Maximum Distance
5 m (16 ft)
PC
CTI Server
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
BGM
Music on Hold
Cable
26 AWG:
24 AWG:
22 AWG:
CAT 5:
Maximum Distance
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
RJ45
(for PC Maintenance)
Maximum Distance
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
10 m (32 ft)
Pager:
Amplifier/Speaker
Maximum Distance
2 m (6 ft)
PC
RS-232C
Printer
PC/CTI Server (via RJ45)
The PBX is equipped with a RJ45 port for communicating between the PBX and a PC or CTI server.
The PC can be used for system programming, diagnostics and external system database storage (save/
load) functions.
The CTI server can be used for connecting PCs on a LAN to provide third party call control CTI. CTI
connection uses the CSTA Phase 3 or TAPI 2.1 protocol.
Note
The operating system of the PC or CTI server required for third party call control depends on your CTI
application software. For details, refer to the manual for your CTI application software.
162
Installation Manual
3.11 Connection of Peripherals
Pin Assignments
No.
Signal Name
Input (I)/Output (O)
Function
TPO+
Transmit data+
TPO-
Transmit data-
TPI+
Receive data+
4-5
Reserved
–
–
TPI-
Receive data-
7-8
Reserved
–
–
BGM/MOH
The PBX provides Background Music and Music on Hold. Up to 2 external music sources (e.g., usersupplied radios) can be connected to the PBX.
CAUTION
•
•
Wiring should be done carefully to prevent undue force being exerted on the plug. Otherwise,
sound may only be heard intermittently.
External Music Jacks are SELV ports and should only be connected to approved SELV devices.
Note
When the PBX and external music sources are not connected to the same ground, hum noise may be
induced into Background Music and Music on Hold.
Pager
Up to 2 paging devices (user-supplied) can be connected to the PBX.
CAUTION
External Paging Jacks are SELV ports and should only be connected to approved SELV devices.
PC/Printer (via RS-232C)
The PBX is equipped with an RS-232C interface. This interface provides communication between the PBX
and the user-supplied devices such as PC or line printers. The RS-232C port is used for system
programming, SMDR, diagnostics and external system database storage (save/load) functions.
When using special accessories such as cable, the user should use those specified in this installation
manual to comply with the limits for a Class B digital device pursuant to the FCC Rules.
Note
Use an RS-232C cross cable for connection between the PBX and PC.
Installation Manual
163
3.11 Connection of Peripherals
Pin Assignments
Circuit Type
No.
Signal Name
Function
EIA
CCITT
RD (RXD)
Receive Data
BB
104
SD (TXD)
ER (DTR)
Transmit Data
Data Terminal Ready
BA
CD
103
108.2
SG
DR (DSR)
Signal Ground
Data Set Ready
AB
CC
102
107
RS (RTS)
CS (CTS)
Request To Send
Clear To Send
CA
CB
105
106
Connection Charts
For connecting a printer/PC with a 9-pin RS-232C connector
Printer/PC (9-pin)
PBX (9-pin)
164
Circuit Type
(EIA)
Signal
Name
Pin No.
Pin No.
Signal
Name
Circuit Type
(EIA)
BB
RD (RXD)
RD (RXD)
BB
BA
SD (TXD)
SD (TXD)
BA
CD
ER (DTR)
ER (DTR)
CD
AB
SG
SG
AB
CC
DR (DSR)
DR (DSR)
CC
CA
RS (RTS)
RS (RTS)
CA
CB
CS (CTS)
CS (CTS)
CB
Installation Manual
3.11 Connection of Peripherals
For connecting a printer/PC with a 25-pin RS-232C connector
Printer/PC (25-pin)
PBX (9-pin)
Circuit Type
(EIA)
Signal
Name
Pin No.
Pin No.
Signal
Name
Circuit Type
(EIA)
BB
RD (RXD)
FG
AA
BA
SD (TXD)
RD (RXD)
BB
CD
ER (DTR)
SD (TXD)
BA
AB
SG
20
ER (DTR)
CD
CC
DR (DSR)
SG
AB
CA
RS (RTS)
CS (CTS)
CB
CB
CS (CTS)
DR (DSR)
CC
RS (RTS)
CF
RS-232C Signals
•
Receive Data (RXD):…(input)
Conveys signals from the printer or the PC.
•
Transmit Data (TXD):…(output)
Conveys signals from the unit to the printer or the PC. A "Mark" condition is held unless data or
BREAK signals are being transmitted.
•
Data Terminal Ready (DTR):…(output)
This signal line is turned ON by the unit to indicate that it is ON LINE. Circuit ER (DTR) ON does
not indicate that communication has been established with the printer or the PC. It is switched OFF
when the unit is OFF LINE.
•
Signal Ground (SG)
Connects to the DC ground of the unit for all interface signals.
•
Data Set Ready (DSR):…(input)
An ON condition of circuit DR (DSR) indicates the printer or the PC is ready. Circuit DR (DSR) ON
does not indicate that communication has been established with the printer or the PC.
•
Request To Send (RTS):…(output)
This lead is held ON whenever DR (DSR) is ON.
•
Clear To Send (CTS):…(input)
An ON condition of circuit CS (CTS) indicates that the printer or the PC is ready to receive data
from the unit. The unit does not attempt to transfer data or receive data when circuit CS (CTS) is
OFF.
•
Frame Ground (FG)
Connects to the unit frame and the ground conductor of the AC power cord.
Installation Manual
165
3.12 LAN Connection
3.12 LAN Connection
3.12.1 LAN Connection
Connection Chart for LAN Connection
The PBX is equipped with an RJ45 port for connecting to a LAN so that IP telephones (IP-PTs, IP
softphones, SIP Extensions), PCs and a CTI Server can be connected on a private IP network.
IP Softphone
RJ45
(for LAN Connection)
PC
CTI Server
Switching Hub
IP-PT
SIP Extension
Notes
•
•
•
166
Switching Hub
PBX (RJ45)
Signal Name Pin No.
Pin No. Signal Name
TX+
RX+
TX-
RX-
RX+
TX+
RX-
TX-
Use an Ethernet straight cable with an RJ45 connector for connection to a switching hub. The cable
should be a 10BASE-T/100BASE-TX CAT 5 or higher cable.
Make sure that all the CAT 5 cables in use are not over 100 m (328 ft) in length.
Make sure to create a spanning tree for LAN connection in order to prevent loops from occurring
in a multi-bridged environment. Otherwise, some packets may circulate for long periods of time and
eventually PBX performance system may degrade.
Installation Manual
3.13 Power Failure Connections
3.13 Power Failure Connections
3.13.1 Power Failure Connections
When the power supply to the PBX fails, power failure transfer (PFT) will switch from the current connection
to the Power Failure Connection. Refer to "2.4.1 Power Failure Transfer" in the Feature Manual for further
information.
Connection
Power Failure Connection connects a specific SLT and a CO line in the event of power failure. The following
analog CO line and extension cards can be used for Power Failure Connections:
•
Analog CO line cards: LCOT16 (4 PFT ports) and LCOT8 (2 PFT ports)
•
Extension cards: MSLC16 (4 PFT ports), SLC16 (4 PFT ports), DHLC8 (2 PFT ports) and SLC8
(2 PFT ports)
To 1 analog CO line card, connect only 1 extension card.
Note
By programming the PBX, a CO line conversation established during power failure can be maintained
even when the power returns and the connection is switched back to the normal configuration from the
Power Failure Connection. However, if no special programming is performed, the connection will be
dropped when power returns.
RJ11
R2
R1
T1
T2
T2
T1
R1
R2
Extension Card
(e.g., SLC8)
CO Line Card
(e.g., LCOT8)
To CO line
To SLT
Accessories and User-supplied Items
Accessories (included): none
User-supplied (not included): RJ11 connectors
Installation Manual
167
3.13 Power Failure Connections
RJ11 Connector Pin Assignments for Analog CO Line Card
PFT Ports 1 and 2
No.
Signal Name
Function
R2
Ring port 2
R1
Ring port 1
T1
Tip port 1
T2
Tip port 2
PFT Ports 3 and 4 (for LCOT16 card only)
No.
Signal Name
Function
R4
Ring port 4
R3
Ring port 3
T3
Tip port 3
T4
Tip port 4
RJ11 Connector Pin Assignments for Extension Card
PFT Ports 1 and 2
No.
Signal Name
Function
T2
Tip port 2
T1
Tip port 1
R1
Ring port 1
R2
Ring port 2
PFT Ports 3 and 4 (for MSLC16/SLC16 card only)
168
Installation Manual
No.
Signal Name
Function
T4
Tip port 4
T3
Tip port 3
R3
Ring port 3
R4
Ring port 4
3.14 Starting the PBX
3.14 Starting the PBX
3.14.1 Starting the PBX
CAUTION
•
•
•
•
•
SD Memory Card must be inserted in the SD Memory Card slot of the IPCMPR card before startup.
Before touching the System Initialize Switch, discharge static electricity by touching ground or
wearing a grounding strap.
Once you have started the PBX and if you unplug the PBX, do not perform the following procedures
to start the PBX again. Otherwise, your programmed data is cleared. To restart the PBX, refer to
"5.1.4 Using the Reset Button".
The PBX will continue to be powered even if the power switch is turned "OFF".
The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located
near the equipment and is easily accessible.
System Initialization Procedure
1. Slide the System Initialize Switch to the "SYSTEM INITIALIZE" position.
RUN Indicator
Reset Button
RESET
SYSTEM
INITIALIZE
NORMAL
System Initialise Switch
Installation Manual
169
3.14 Starting the PBX
2. Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will
flash.
Note
For safety reasons, do not stretch, bend, or pinch the AC power cord.
To AC Outlet
3. While the RUN indicator is flashing, slide the System Initialize Switch back to the "NORMAL" position.
Depending on the configuration, initialization takes about 1 min to 3 min. If successfully executed, the
RUN indicator will stop flashing and stay lit.
All data will be cleared, and the PBX as well as all optional service cards (except for the IP-GW card) will
be initialized to the default values. The DPTs should show the time as 01:00.
The data of the IP-GW card will not be initialized.
Note
Use only the AC power cord included with the PSU.
LED Indications
Indication
Color
Description
RUN
Green
PBX status indication
•
OFF: Power Off (includes normal reset)
•
ON: Power On and running (on-line)
•
Flashing (60 times per minute): Starting up
•
Flashing (120 times per minute): Starting up or resetting with:
•
the System Initialize Switch in "SYSTEM INITIALIZE"
position
•
the SD Memory Card not inserted
ALARM
Red
Alarm indication
•
OFF: Normal
•
ON: Alarm (CPU stop, alarm for each optional service card)
•
Flashing: Alarm (IPCMPR file error in restarting)
Confirming the CO Line Connection
After initialization, program the PBX and connect CO lines to the PBX.
To confirm that the CO lines are successfully connected, dial [ ] [3] [7] + CO line number (3 digits) on a PT,
or press the PT's S-CO button. You will hear a dial tone if the CO line is available and connected.
170
Installation Manual
Section
Guide for the KX-TDE Maintenance Console
Explains the installation procedure, structure, and basic
information of the KX-TDE Maintenance Console.
Installation Manual
171
4.1 Overview
4.1
Overview
4.1.1
Overview
KX-TDE Maintenance Console is designed to serve as an overall system programming reference for the
PBX. To program and administer the PBX by PC, you need to install the KX-TDE Maintenance Console onto
the PC.
This section describes overview and installation of the KX-TDE Maintenance Console only.
KX-TDE Maintenance Console*1
Menu Bar
System Menu
*1
The contents and design of the software are subject to change without notice.
172
Installation Manual
4.2 Connection
4.2
Connection
4.2.1
Connection
LAN Connection via RJ45 Port of IPCMPR Card
RJ45 (for LAN Connection)
Switching Hub
To network port
PC
Note
For pin assignments and maximum cabling distance, refer to "3.11.1 Connection of Peripherals".
Serial Interface Connection
RJ45 (for PC Maintenance)
To LAN Port
PC
To COM Port
PC
RS-232C Port
Note
For pin assignments and maximum cabling distance, refer to "3.11.1 Connection of Peripherals".
Installation Manual
173
4.2 Connection
External Modem Connection
Modem
To RS-232C port (25-pin)
To CO line/PBX extension port
assigned as the CO line destination
RS-232C Port
(9-pin)
External Modem (25-pin)
PBX (9-pin)
Signal Name
Pin No.
Pin No.
Signal Name
RD (RXD)
RD (RXD)
SD (TXD)
SD (TXD)
ER (DTR)
20
ER (DTR)
DR (DSR)
DR (DSR)
After connecting the PBX and the external modem, set the power switch of the external modem to "ON",
then the external modem will be initialized with the default values.
The following AT command settings may be required for the modem:
•
The Data Terminal Ready (DTR) signal should be ignored.
•
The Data Terminal Equipment (DTE)/Modem flow control should be turned off.
•
Data compression should be disabled.
•
Error Correction is not necessary.
Notes
•
•
•
174
Use an RS-232C straight cable for connection between the PBX and external modem.
An AT command (for initialization, enabling automatic answer, etc.) can only be programmed by
KX-TDE Maintenance Console. "AT&F" is stored as the default value.
For more information about the AT command, refer to the external modem's instructions.
Installation Manual
4.3 Installation of the KX-TDE Maintenance Console
4.3
Installation of the KX-TDE Maintenance
Console
4.3.1
Installing and Starting the KX-TDE Maintenance Console
System Requirements
Required Operating System
•
Microsoft ® Windows ® 2000, Windows XP, or Windows Vista
Minimum Hardware Requirements
•
•
•
CPU: 300 MHz Intel ® Celeron ® microprocessor
HDD: 100 MB of available hard disk space
RAM: 128 MB of available RAM
Installing the KX-TDE Maintenance Console
Notes
•
•
Make sure to install and use the latest version of the KX-TDE Maintenance Console.
To install or uninstall the software on a PC running Windows 2000 Professional or Windows XP
Professional, you must be logged in as a user in either the "Administrators" or "Power Users" group.
1. Copy the setup file of the KX-TDE Maintenance Console to your PC. (Its icon is shown here, on the left.)
2. Double-click the setup file to run the installer.
3. Follow the on-screen instructions provided by the installation wizard.
Starting the KX-TDE Maintenance Console and Assigning the Basic
Items (Quick Setup)
When you start the KX-TDE Maintenance Console with the Installer Level Programmer Code and connect
to the PBX for the first time after initialization (with the factory default setting), Quick Setup will launch
automatically. During Quick Setup, you will set up the basic items. For details about the basic items, refer to
"2.3.4 Quick Setup" in the Feature Manual.
1.
Connect the PC to the PBX with an Ethernet straight cable or RS-232C.
2.
Start the KX-TDE Maintenance Console from the Start menu.
3.
"Information before programming" appears.
a. Carefully read this important additional information, which includes updates to this and other
manuals.
b. Click OK to close this window.
Installation Manual
175
4.3 Installation of the KX-TDE Maintenance Console
4.
a. Enter the Installer Level Programmer Code (default: INSTALLER).
The Programmer Code authorizes different programming levels, and the Quick Setup is only
available when you start the KX-TDE Maintenance Console with the Installer Level Programmer
Code.
Note
There are 2 other Programmer Codes with limited authorisation: Administrator Level (default:
ADMIN), and User Level (default: USER).
b. Click OK.
5.
a. Click Connect → LAN or RS-232C from the menu bar, depending on the serial interface
connection with the PBX.
b. In the next screen, enter the system password for installer (default: 1234).
c. Click OK.
6.
Follow the instructions of the Quick Setup wizard and assign the basic items (Quick Setup).
The system menu appears. You may now begin programming the PBX.
Notes
•
•
176
During a long programming session, it is highly recommended that you periodically save the
system data to the SD Memory Card. If the PBX undergoes a sudden power failure or if the system
is reset for some reason, all the system data in RAM will be lost. However, if system data has been
saved to the SD Memory Card, it can be easily restored.
To save the system data to the SD Memory Card, (1) click the "SD Memory Backup" icon before
resetting the PBX or turning off the power, or (2) exit the KX-TDE Maintenance Console so that the
PBX automatically saves the system data.
When programming PBX data which can be displayed on a proprietary telephone (PT) (extension
names, group names, System Speed Dialing names, etc.), it is possible to enter characters which
cannot be displayed on a KX-T7600 series PT.
Characters which can be displayed on a KX-T7600 series PT are shown below in the white cells.
Installation Manual
4.3 Installation of the KX-TDE Maintenance Console
•
The PC will not perform any shutdown operation, or enter the power-saving system standby mode
while the KX-TDE Maintenance Console is connected to the PBX. To perform either of the
operations above, first close the connection to the PBX.
CAUTION
Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX
to fail to start when you try to restart the system.
Installation Manual
177
4.3 Installation of the KX-TDE Maintenance Console
178
Installation Manual
Section
Troubleshooting
This section provides information on the PBX and telephone
troubleshooting.
Installation Manual
179
5.1 Troubleshooting
5.1
Troubleshooting
5.1.1
Installation
PROBLEM
You cannot make/receive calls
via an IP network.
PROBABLE CAUSE
SOLUTION
•
IP-EXT/IP-GW/DSP card
malfunction
•
Replace the corresponding card.
•
IPCMPR card malfunction
•
Replace the IPCMPR card (be sure to
turn off the PBX when replacing).
•
Not enough activation keys •
Purchase additional activation key
cards. Please consult a certified dealer
for details.
•
Poor connection
Make sure that an 8-pin twisted pair
cable is used for connection.
Make sure that none of the CAT 5
cables in use are over 100 m (328 ft) in
length.
Make sure that a straight cable is used
for connection to a switching hub.
•
•
•
•
Network malfunction
•
•
IP-PTs/SIP Extensions do not
operate.
•
IP-EXT/DSP card
malfunction
•
Replace the corresponding card.
•
IPCMPR card malfunction
•
Replace the IPCMPR card (be sure to
turn off the PBX when replacing).
•
Not enough activation keys •
Purchase additional activation key
cards. Please consult a certified dealer
for details.
•
IP-PT/SIP Extension not
registered
•
Register the corresponding IP-PT/SIP
Extension.
•
IP-PT/SIP Extension
malfunction
•
Replace the IP-PT/SIP Extension.
•
Poor connection
•
Make sure that an 8-pin twisted pair
cable is used for connection.
Make sure that none of the CAT 5
cables in use are over 100 m (328 ft) in
length.
Make sure that a straight cable is used
for connection to a switching hub.
•
•
180
Installation Manual
Make sure that all network devices in
use are switched on.
Make sure that there is no unwanted
firewall in the IP network.
5.1 Troubleshooting
PROBLEM
PROBABLE CAUSE
•
Network malfunction
SOLUTION
•
•
Extensions (except IP-PT/SIP
Extension) do not operate.
Make sure that all network devices in
use are switched on.
Make sure that the IP-PT/SIP
Extension is not blocked by the firewall
or other network devices.
•
Extension card malfunction •
Replace the corresponding card.
•
Poor connection between
•
the PBX and the extension
Take the extension and plug it into the
same extension port using a short
telephone cord. If the extension works,
then the connection between the PBX
and the extension must be repaired.
•
A telephone with an A-A1
relay is connected.
•
•
Make sure that a 2-wire cord is used.
Make sure that the A-A1 relay switch of
the telephone is in "OUT" or "OFF"
position.
•
Extension malfunction
•
Take the extension and plug it into
another extension port that is working.
If the extension does not work, replace
the extension.
•
Wrong type of PSU
•
Replace the PSU with the appropriate
type.
•
Press the Reset Button (refer to "5.1.4
Using the Reset Button").
Turn off the power switch, and then turn
it back on.
Turn off the power switch, and then
unplug the PBX. After 5 minutes, plug
the PBX back in, and turn the power
switch back on.
The PBX does not operate
properly.
•
•
Noise on external paging.
•
Induced noise on the wire
between the PBX and the
amplifier.
•
Use a shielded cable as the connection
wire between the PBX and amplifier. A
short shielded cable is recommended.
Distorted external music.
•
Excessive input level from
external music source.
•
Decrease the output level of the
external music source by using the
volume control on the music source.
•
Alternate Calling—Ring/Voice
and Live Call Screening (LCS)
do not function as set when using
a Wireless Phone (KX-T7880/
KX-T7885/KX-TD7894/KXTD7895).
•
Voice-calling mode and
Hands-free mode with LCS •
are not available with
Wireless Phones.
Switch the calling mode to ring-calling.
Set the LCS mode to "Private".
The ALARM indicator on the
front of the shelf turns on red.
A major system error
occurs in the PBX.
See the error log using the KX-TDE
Maintenance Console (refer to "5.1.5
Troubleshooting by Error Log").
•
•
Installation Manual
181
5.1 Troubleshooting
PROBLEM
The LINK indicator of the IPEXT/IP-GW/IPCMPR does not
turn on.
PROBABLE CAUSE
SOLUTION
•
IP-EXT/IP-GW card
malfunction
•
Replace the corresponding card.
•
IPCMPR card malfunction
•
Replace the IPCMPR card (be sure to
turn off the PBX when replacing).
•
Poor connection
•
Make sure that an 8-pin twisted pair
cable is used for connection.
Make sure that none of the CAT 5
cables in use are over 100 m (328 ft) in
length.
Make sure that a straight cable is used
for connection to a switching hub.
•
•
•
182
Installation Manual
Network malfunction
•
Make sure that all network devices in
use are switched on.
5.1 Troubleshooting
5.1.2
Connection
Connection between the PBX and a PT:
Can you dial
an extension?
CAUSE
No
SOLUTION
The T/R is connected to the D1/D2.
D1
D2
PBX
D1
D2
Use the correct cord (the
inner 2 wires are for T/R and
the outer 2 wires are for
D1/D2)
Extension
Connection between the PBX and an SLT:
CAUSE
SOLUTION
The T/R is connected to the D1/D2.
D1
D2
PBX
Yes
Extension
Use the correct cord (the
inner 2 wires are for T/R).
If a telephone equipped
with an A-A1 relay is
connected to the PBX, set
the A-A1 relay switch of the
telephone to "OFF".
Connection between the PBX and an SLT that is polarity-sensitive:
CAUSE
SOLUTION
The "T" is connected to the "R".
D1
D2
PBX
Reverse the connections of
the T/R.
Extension
(Continued on the next page.)
Installation Manual
183
5.1 Troubleshooting
Connection between the central office and the PBX:
(Continued from the
previous page.)
Can you dial
out on a
CO line?
CAUSE
CO line is connected to the T2/T1.
T2
R1
T1
R2
No
CO line
PBX
CO line is connected to the T2/R1.
T2
R1
T1
R2
CO line
184
Installation Manual
PBX
SOLUTION
Reconnect the CO line to
the T1/R1 or T2/R2 of the
telephone jack using 2conductor wiring.
5.1 Troubleshooting
5.1.3
Operation
PROBLEM
PROBABLE CAUSE
SOLUTION
•
Cannot set the IP address,
subnet mask address, and
PBX IP address to the IPPT.
•
An unusable value is being •
set.
Set an IP address within the valid
range. IP address of the IP-PT/PBX:
"1.0.0.0" to "223.255.255.255" Subnet
mask address: "1.0.0.0" to
"255.255.255.254"
•
Cannot register the IP-PT.
•
The necessary network
parameters are not set to
the IP-PT.
When not using a DHCP server, set the
IP address, subnet mask address, and
enter the PBX IP address. If necessary,
also enter the IP address of the default
gateway.
When using a DHCP server, enter the
PBX IP address.
•
•
•
•
The wrong IP address,
subnet mask address, PBX
IP address, or default
gateway address was
entered.
Check each parameter and enter the
correct value.
•
The Ethernet cable is not
connected correctly.
•
Check the Ethernet cable connections.
•
The DHCP server is not
active.
•
•
Restart the DHCP server.
Disable DHCP and re-enter settings as
appropriate.
•
The HANDSET/HEADSET •
selector is set to the
"HEADSET" position.
When the headset is not used, set the
HANDSET/HEADSET selector to the
"HANDSET" position.
The IP-PT cannot connect to •
the PBX.
•
When using the
speakerphone on an APT,
nothing is audible.
•
•
When using the
speakerphone/monitor
mode with a DPT, nothing is
audible.
The "HEADSET" mode is
selected by Personal
Programming, "Handset/
Headset Selection".
•
When the headset is not used, select
the "HANDSET" mode by Personal
Programming.
•
The PT does not ring.
•
The ringer volume is off.
•
Turn on the ringer volume.
•
During a power failure,
extensions connected to
ports 1 to 4 of MSLC16/
SLC16 and ports 1 to 2 of
DHLC8/SLC8 cards do not
operate.
•
A DPT or APT is connected •
to the extension port.
The dialing mode (tone or •
pulse) is incorrect.
Disconnect the DPT or APT and
connect an SLT.
Set the Tone/Pulse switch to the other
position.
Originating an outside call,
call transfer, or conference
cannot be performed.
•
The corresponding flexible •
button does not exist on the
PT.
Programme the flexible button. Refer to
"1.20.2 Flexible Buttons" in the Feature
Manual.
•
•
Installation Manual
185
5.1 Troubleshooting
PROBLEM
•
Cannot register the PS.
PROBABLE CAUSE
SOLUTION
•
Wrong Personal
•
Identification Number (PIN)
is registered to the PS.
Enter the PIN set to the PBX into the
PS.
•
CS is not connected
properly.
•
Make sure that the cable is connected
properly with correct pin assignments.
Also, make sure that the cable does not
make short circuits.
Switch all DIP switches off.
CSIF card is not working.
•
Install the CSIF card properly.
CS is not working.
•
Make sure that the cable is connected
properly with correct pin assignments.
Also, make sure that the cable does not
make short circuits.
Switch all DIP switches off.
•
PS becomes out of range.
•
•
Cannot make calls using the •
PS.
•
•
•
•
•
186
•
Location of CS is not good. •
Locate the CS properly (refer to "3.9.5
Site Survey" ).
•
Access system of the PS is •
not properly set.
Change the access system setting of
the PS to the appropriate system or
automatic.
Noise is frequent while using •
the PS.
Conversations disconnect
•
while using the PS.
PS stays out of service
when the CS status is
changed from Out of
Service to In Service.
Installation Manual
•
Call handover is not
working.
PS is out of CS coverage
area.
•
•
It may take about 20 s for
CS to start up after the
status has been changed to
In Service.
Locate the CS properly (refer to "3.9.5
Site Survey" ).
Wait until the CS starts up.
5.1 Troubleshooting
5.1.4
Using the Reset Button
If the PBX does not operate properly, use the Reset Button. Before using the Reset Button, try the system
feature again to confirm whether there definitely is a problem or not.
CAUTION
In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD
ACCESS" LED is off before pressing the Reset Button.
Notes
•
•
When the System Initialize Switch is set to "NORMAL", pressing the Reset Button causes the
following:
– Camp-on is cleared.
– Calls on hold are terminated.
– Calls on exclusive hold are terminated.
– Calls in progress are terminated.
– Call park is cleared.
Other data stored in memory, except the above, are not cleared.
Be aware that pressing the Reset Button with the System Initialize Switch in the "SYSTEM
INITIALIZE" position clears all data stored in the PBX. Do not perform this operation unless you
intend to delete all data from the PBX.
Operation
If the PBX does not operate properly:
1. Slide the System Initialize Switch to the "NORMAL" position.
2. Press the Reset Button for about 1 second.
RUN Indicator
LED
Reset Button
System Initialize Switch
Installation Manual
187
5.1 Troubleshooting
5.1.5
Troubleshooting by Error Log
When a major system error occurs in the PBX, the ALARM indicator on the front of the shelf turns on red,
and the system logs the error information.
Error Log Display Format
Below is the display format of the error log. For information about how to view the error log using the KXTDE Maintenance Console, refer to "2.5.8 Utility—Error Log" in the PC Programming Manual.
Example: KX-TDE Maintenance Console
Example: Station Message Detail Recording (SMDR)
07/01/01 10:37AM MJ ALM #000 10000 MPR WDT overflow
07/01/01 11:07AM MN ALM #010 10000 AC power down
07/01/01 03:55PM MN ALM #301 10501 Digital trunk RAI reception
Description
Item
Date
The date of the error detection.
Time
The time of the error detection.
Level
188
Description
Error Code
Installation Manual
Minor (MN ALM)
Displays minor errors, which affect only a certain part of system
operation.
Major (MJ ALM)
Displays major errors, which affect operation of the whole
system, or result in system failure.
The 3-digit error code assigned by the PBX.
5.1 Troubleshooting
Item
Sub Code
Description
The 5-digit sub code of the relevant hardware (XYYZZ).
•
X: Shelf type
– Physical shelf: " " (blank)
– Virtual shelf: "*" (asterisk)
•
YY: Slot number
– KX-TDE100 (Physical slot): 00 to 06
(00: IPCMPR Card Slot; 01 to 06: Free Slots)
– KX-TDE200 (Physical slot): 00 to 11
(00: IPCMPR Card Slot; 01 to 11: Free Slots)
– KX-TDE100/KX-TDE200 (Virtual slot): 01 to 08
(01 to 04: Virtual CO Line Slots; 05 to 08: Virtual
Extension Slots)
•
ZZ: Port number
– For optional service cards except OPB3 card:
Port number (01 to 16) will be displayed.
– For OPB3 card:
Sub slot number (1 to 3) + port number (1 to 4) will
be displayed as follows:
•
Sub slot 1 of OPB3: 11 to 14
•
Sub slot 2 of OPB3: 21 to 24
•
Sub slot 3 of OPB3: 31 to 34
Note
When there is no parameter for slot and port number, YY
and ZZ will be displayed as "00".
Example: Sub code for IPCMPR card = " 0000"
Error Message
A description of the error.
Log Information
Displays probable causes of the errors and their solutions.
Installation Manual
189
5.1 Troubleshooting
190
Installation Manual
Index
Installation Manual
191
Index
Numerics
16-Channel Echo Canceller Card (KX-TDA0166)
29, 119
44
16-Channel SIP Extension Activation Key (KX-NCS4716)
16-Channel VoIP DSP Card (KX-TDE0110)
29, 82
30, 111
16-Channel VoIP Extension Card (KX-TDA0470)
30, 94
16-Channel VoIP Gateway Card (KX-TDA0490)
30, 85
16-Port Analog Trunk Card (KX-TDA0181)
16-Port Digital Extension Card (KX-TDA0172)
29, 104
30, 109
16-Port Single Line Telephone Extension Card (KX-TDA0174)
16-Port Single Line Telephone Extension with Message Lamp Card (KX30, 109
TDA0175)
145
2.4 GHz Portable Station, After Site Survey
137
2.4 GHz Portable Station, Before Site Survey
2.4 GHz Portable Station, Connecting a CS
146
131
2.4 GHz Portable Station, Procedure Overview
129
2.4 GHz Portable Station, Radio Method
2.4 GHz Portable Station, Site Planning
133
141
2.4 GHz Portable Station, Site Survey
29, 96
4 Cell Station Interface Card (KX-TDA0143)
4-Channel IP Trunk Activation Key (KX-NCS4104)
44
30, 120
4-Channel Message Card (KX-TDA0191)
30, 92
4-Channel VoIP Gateway Card (KX-TDA0484)
4-Port Doorphone Card (KX-TDA0161)
29, 114
29, 116
4-Port External Input/Output Card (KX-TDA0164)
29, 82
64-Channel VoIP DSP Card (KX-TDE0111)
8 Cell Station Interface Card (KX-TDA0144)
29, 96
44
8-Channel IP Proprietary Telephone Activation Key (KX-NCS4508)
8-Channel IP Softphone/IP Proprietary Telephone Activation Key (KXNCS4208)
44
30, 85
8-Port Analog Trunk Card (KX-TDA0180)
30, 87
8-Port Caller ID Card (KX-TDA0193)
8-Port Digital Extension Card (KX-TDA0171)
29, 102
29, 99
8-Port Digital Hybrid Extension Card (KX-TDA0170)
30, 106
8-Port Single Line Telephone Extension Card (KX-TDA0173)
Cable Handling
62
Characteristics
33
87
CID8 Card (KX-TDA0193)
35
CO Line Card, Physical
CO Line Card, Virtual
35, 84
170
CO Line Connection
Components, System
166
Connection Chart for LAN Connection
Connection Diagram, System
27
64
Connector Types
61
Cover for Blank Slot
CS (for 2.4 GHz Portable Station)
146
CS, Basic
CS, High-density
CSIF4 Card (KX-TDA0143)
96
96
CSIF8 Card (KX-TDA0144)
CTI Server Connection (via USB version 2.0)
CTI—First Party Call Control
128
162
CTI—Third Party Call Control
162
DHLC8 Card (KX-TDA0170)
99
Digital EXtra Device Port (Digital XDP) Connection
126
Digital XDP
Digital XDP Connection, Using a Modular T-Adaptor
Digital XDP Connection, Using an EXtra Device Port
104
DLC16 Card (KX-TDA0172)
DLC8 Card (KX-TDA0171)
102
114, 159
Door Opener
114, 159
Doorphone
DPH4 Card (KX-TDA0161)
114
82
DSP16 Card (KX-TDE0110)
82
DSP64 Card (KX-TDE0111)
126
126
127
About the software version of your PBX
12
42
Activation Key
Activation Key Card
44
43, 45
Activation Key File
Activation Key for Software Upgrade to Enhanced Version (KXNCS4910)
44
42
Activation Key, in the DSP16/DSP64 Card
43
Activation Key, in the SD Memory Card
Activation Key, Maximum Number
42
68, 69
Amphenol Connector
67
Attaching to an Amphenol Connector
Attaching to an RJ45 Connector
66
Basic CS
Basic Shelf
26
26
Basic Shelf, Construction
163
BGM
Blank Slot Cover (KX-A258)
61
ECHO16 Card (KX-TDA0166)
119
Editing the CS Name using the KX-TDE Maintenance Console
EIO4 Card (KX-TDA0164)
116
188
Error Log
108
EXT-CID Card (KX-TDA0168)
Extension Caller ID Card (KX-TDA0168)
29, 108
35
Extension Card, Physical
35, 84
Extension Card, Virtual
External Relay
116, 118, 159
116, 118, 159
External Sensor
124, 126
EXtra Device Port (XDP) Mode
Ferrite Core
66
128
First Party Call Control CTI Connection
Floor Standing (KX-TDE200 Only)
74
58
Frame ground Connection
53
Front Cover, Closing
Front Cover, Opening
52
High-density CS
Cable Distance
192
121
Installation Manual
97
Index
Information about the Virtual Cards
84
48
Installation Precautions
IP Convergence Main Processing Card (IPCMPR Card)
79
IPCMPR Card
34
IPCMPR Card Slot
111
IP-EXT16 Card (KX-TDA0470)
IP-GW16 Card (KX-TDA0490)
94
92
IP-GW4E Card (KX-TDA0484)
38
Load Figure Calculation
L-Type Power Supply Unit (KX-TDA0103)
79
Key Management System
44
61
KX-A258 (Blank Slot Cover)
44
KX-NCS4104 (4-Channel IP Trunk Activation Key)
KX-NCS4208 (8-Channel IP Softphone/IP Proprietary Telephone Activation
Key)
44
44
KX-NCS4508 (8-Channel IP Proprietary Telephone Activation Key)
KX-NCS4716 (16-Channel SIP Extension Activation Key)
44
KX-NCS4910 (Activation Key for Software Upgrade to Enhanced
44
Version)
KX-TDA0103 (L-Type Power Supply Unit)
29, 54
29, 54
KX-TDA0104 (M-Type Power Supply Unit)
29, 54
KX-TDA0108 (S-Type Power Supply Unit)
KX-TDA0143 (4 Cell Station Interface Card)
29, 96
29, 96
KX-TDA0144 (8 Cell Station Interface Card)
29, 114
KX-TDA0161 (4-Port Doorphone Card)
KX-TDA0164 (4-Port External Input/Output Card)
29, 116
29, 119
KX-TDA0166 (16-Channel Echo Canceller Card)
29, 108
KX-TDA0168 (Extension Caller ID Card)
KX-TDA0170 (8-Port Digital Hybrid Extension Card)
29, 99
29, 102
KX-TDA0171 (8-Port Digital Extension Card)
29, 104
KX-TDA0172 (16-Port Digital Extension Card)
KX-TDA0173 (8-Port Single Line Telephone Extension Card)
30, 106
30, 109
KX-TDA0174 (16-Port Single Line Telephone Extension Card)
KX-TDA0175 (16-Port Single Line Telephone Extension with Message Lamp
Card)
30, 109
30, 85
KX-TDA0180 (8-Port Analog Trunk Card)
30, 85
KX-TDA0181 (16-Port Analog Trunk Card)
KX-TDA0187 (T-1 Trunk Card)
30, 88
30, 113
KX-TDA0190 (Optional 3-Slot Base Card)
30, 120
KX-TDA0191 (4-Channel Message Card)
KX-TDA0193 (8-Port Caller ID Card)
30, 87
30, 83
KX-TDA0196 (Remote Card)
30, 90
KX-TDA0290 (PRI Card [PRI23])
KX-TDA0470 (16-Channel VoIP Extension Card)
30, 111
30, 92
KX-TDA0484 (4-Channel VoIP Gateway Card)
30, 94
KX-TDA0490 (16-Channel VoIP Gateway Card)
KX-TDE Maintenance Console, Connection
173
175
KX-TDE Maintenance Console, Installation
172
KX-TDE Maintenance Console, Overview
KX-TDE Maintenance Console, Quick Setup
175
175
KX-TDE Maintenance Console, System Requirements
29, 82
KX-TDE0110 (16-Channel VoIP DSP Card)
KX-TDE0111 (64-Channel VoIP DSP Card)
29, 82
Maintenance Console
172
126
Master DPT, Digital XDP
MOH
163
120
MSG4 Card (KX-TDA0191)
109
MSLC16 Card (KX-TDA0175)
M-Type Power Supply Unit (KX-TDA0104)
29, 54
Names and Locations
51
OPB3 Card (KX-TDA0190)
113
Optional 3-Slot Base Card (KX-TDA0190)
Optional Equipment
29
59
Optional Service Card, Installation
Optional Service Card, Maximum Number
Optional Service Card, Removal
63
30, 113
35
Pager
163
Panasonic Proprietary Telephones, Compatible
Panasonic Proprietary Telephones, Incompatible
123
Parallel Connection of the Extensions
Parallel Connection, Using a Modular T-Adaptor
Parallel Connection, Using an EXtra Device Port
124, 126
Parallel Mode
Password Security
10
163
PC Connection (via RS-232C)
162
PC Connection (via USB version 2.0)
Peer-to-peer Connection
23
35
Physical CO Line Card
35
Physical Extension Card
Power Failure Connections
167
54
Power Supply Unit
38
Power Supply Unit Selection
Power Supply Unit, Installation
55
56
Power Supply Unit, Replacement
30, 90
PRI Card (PRI23) (KX-TDA0290)
PRI23 Card (KX-TDA0290)
90
163
Printer Connection (via RS-232C)
54
PSU
PSU Capacity
39
38, 54
PSU-L
38, 54
PSU-M
PSU-S
38, 54
124
124
Quick Setup
175
LCOT16 Card (KX-TDA0181)
LCOT8 Card (KX-TDA0180)
170
LED Indications, PBX
29, 54
85
85
Radio Method, 2.4 GHz Portable Station
30, 83
Remote Card (KX-TDA0196)
Reset Button
187
83
RMT Card (KX-TDA0196)
129
Installation Manual
193
Index
RUN Indicator
169
Wall Mounting (KX-TDE100)
Wall Mounting (KX-TDE200)
48
Wiring Precautions
Safety Installation Instructions
48
54
Safety Instructions
79
SD Memory Card
Site Planning, 2.4 GHz Portable Station
133
141
Site Survey, 2.4 GHz Portable Station
126
Slave DPT, Digital XDP
SLC16 Card (KX-TDA0174)
109
106
SLC8 Card (KX-TDA0173)
34
Slot for the IPCMPR Card
Slots for Physical Cards (Free Slots)
34
34
Slots for Virtual CO Line Cards
34
Slots for Virtual Extension Cards
Specifications
31
33
Specifications, Characteristics
31
Specifications, General Description
Specifications, System Capacity
34
169
Starting the PBX
29, 54
S-Type Power Supply Unit (KX-TDA0108)
Surge Protector Installation
76
34
System Capacity
System Components Table
System Connection Diagram
27
22
System Highlights
169
System Initialization Procedure
System Initialize Switch
169, 187
175
System Requirements
T1 Card (KX-TDA0187)
88
30, 88
T-1 Trunk Card (KX-TDA0187)
Terminal Equipment, Maximum Number
Troubleshooting, by Error Log
188
183
Troubleshooting, Connection
180
Troubleshooting, Installation
Troubleshooting, Operation
185
Troubleshooting, Using the Reset Button
37
187
Unpacking
50
V-IPEXT32 (Virtual 32-Channel VoIP Extension Card)
V-IPGW16 (Virtual 16-Channel VoIP Gateway Card)
Virtual 16-Channel VoIP Gateway Card (V-IPGW16)
Virtual 32-Channel SIP Extension Card (V-SIPEXT32)
Virtual 32-Channel VoIP Extension Card (V-IPEXT32)
84
Virtual Cards
35, 84
Virtual CO Line Card
Virtual CO Line Slot
34
35, 84
Virtual Extension Card
34
Virtual Extension Slot
V-SIPEXT32 (Virtual 32-Channel SIP Extension Card)
Wall Mounting (CS)
194
155
Installation Manual
84
84
84
84
84
84
72
70
Index
Installation Manual
195
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Puerto Rico, Inc.
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5,
Carolina, Puerto Rico 00985
http://www.panasonic.com/csd
Copyright:
This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use
only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic
Communications Co., Ltd.
2007 Panasonic Communications Co., Ltd. All Rights Reserved.
PSQX4179ZA KK0507EK0 (v0.001)

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 196
Page Mode                       : UseOutlines
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d3cb414b-9090-4123-93c4-ab5c8b9b4070
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Create Date                     : 2007:02:22 17:01:54Z
Modify Date                     : 2007:05:31 11:36:46-04:00
Metadata Date                   : 2007:05:31 11:36:46-04:00
Creator Tool                    : FrameMaker 7.0
Document ID                     : uuid:64daf61a-f27e-468c-8d4c-1abe6007c4d4
Format                          : application/pdf
Creator                         : kiyota
Title                           : 100_TDE_IM_07-02.book
Author                          : kiyota

EXIF Metadata provided by EXIF.tools