Panasonic of North America 96NKX-TG2730 FHSS cordless telephone system User Manual KX TG2730S Apply

Panasonic Corporation of North America FHSS cordless telephone system KX TG2730S Apply

operating instructions

2.4GHz Multi-Handset Cordless Phone SystemModel No. KX-TG2730SPulse-or-tone-dialing capabilityOperating InstructionsCharge the battery for about 15 hours before initial use.PLEASE READ BEFORE USE AND SAVE.Contents:Location of Controls 2Connections 5Battery Installation/Battery Charge 6Recording a Greeting Message 7Making/Answering calls with the Handset 8Making/Answering calls with the Base Unit 9Caller ID Service 9Automatic Answering Operation 10Listening to Messages 10Important Safety Instructions 11FCC and Other Information 13
–2–Please read IMPORTANT SAFETYINSTRUCTIONS on page 11 before use.Read and understand all instructions.Location of Controls■HandsetINTERCOM TRANSFERCLEARSP-PHONEHOLDFUNCTIONREDIAL CALL WAIT21345678TONE09CONFTALKOFFFLASHPAUS EBack sideSpeaker Headset Jack (TONE) Button (TALK) Button (Speakerphone) ButtonButtonCONF (Conference)/FUNCTIONMicrophoneCharge ContactsAntennaDisplay(OFF) Button (HOLD/CLEAR)/ (INTERCOM/TRANSFER) Button(PAUSE/REDIAL) ButtonSoft KeysNavigator Key( , , , )(FLASH/CALL!WAIT) Button
–3–■Base unit123ERASESTOPHOLDCONF NEW MESSAGE / SLOW TALK MAILBOXMICDIGITAL SPREAD SPECTRUM CHARGEMULTI HANDSET0REDIAL/PAUSEMUTETONEDIGITAL SP PHONEFLASH/CALL WAIT132456879TRANSFERINTERCOMPRIVACYMEMOGREETINGPROGRAM RINGER/AUTORINGERLOUD/ ROOMMONITORIN USEDisplayMIC (Microphone)CHARGE Indicator (PROGRAM) Button(RINGER/AUTO) Button(DIGITALÒSP-PHONE) Button and Indicator(MUTE) Button and Indicator(FLASH/CALLÒWAIT) Button(REDIAL/PAUSE) ButtonIN USE Indicator (INTERCOM/TRANSFER) Button(PRIVACY) Button and Indicator (HOLD) Button (CONF) (Conference) Button
–4–■Base unitMICCHARGEERASESTOPMULTI HANDSET123 NEW MESSAGE / SLOW TALK MAILBOXHOLDCONFREDIAL/PAUSEMUTETONEDIGITAL SP PHONEFLASH/CALL WAITDIGITAL SPREAD SPECTRUM TRANSFERINTERCOM0132456879PRIVACYRINGERLOUD/ MEMOGREETINGPROGRAMRINGER/AUTOROOMMONITORIN USE(ERASE) Button (STOP) Button(GREETING) Button(ANSWERÒON) Button and Indicator (MEMO) Button ROOM MONITOR/INTERCOM Indicator Antenna(TONE) Button AntennaCharge Contacts(MAILBOX) ButtonsNavigator Key( , , , )
–5–Connections■Connect the AC adaptor and the telephone line cord.•USE ONLY WITH Panasonic AC ADAPTOR PQLV10. •The AC adaptor must remain connected at all times. (It is normal for theadaptor to feel warm during use.)HookTelephone Line CordAC AdaptorPower Outlet (AC 120 V, 60 Hz)Single-Line Telephone Jack (RJ11C)Fasten the AC adaptor cord to prevent it from being disconnected.Raise the antennas.
–6–Battery Installation/Battery Charge■RechargeRecharge the battery when:–"Recharge battery" is displayed,–" " flashes on the display, or– the handset beeps every minute while it is in use.•Clean the handset and the base unit charge contacts with a soft, drycloth once a month. Clean more often if the unit is subject to grease,dust or high humidity. If not, the battery may not charge properly.•If the battery is fully charged, you do not have to place the handset on thebase unit until "Recharge battery" is displayed and/or " " flashes.This will maximize the battery life.•The battery cannot be overcharged.■Battery installation1 Install the battery in the handset.2 Close the handset cover.■Battery chargeTo power the handset, charge the battery.Place the handset on the base unit for about 15 hours before initial use.A nickel cadmium battery that is recyclable powers the productyou have purchased. At the end of its useful life, under variousstate and local laws, it is illegal to dispose of this battery intoyour municipal waste stream. Please call 1-800-8-BATTERY for information on how to recycle thisbattery.
–7–You can record a personal greeting message of up to 2 minutes. If a greetingmessage is not recorded, one of two pre-recorded greetings will be playedwhen a call is received.•All messages (greeting, incoming, etc.) are stored in digital memory. Thetotal recording time is about 15 minutes. We recommend you record abrief greeting message in order to leave more time for recording newmessages.1 Press and hold (GREETING) until a long beep is heard.2 After the long beep, talk clearly, about 8 inches (20 cm) away from the MIC(microphone).3 When finished, press (GREETING).•If you do not record a greeting message, one of two messages will be playedwhen a call is received, depending on the caller’s recording time.Recording a Greeting Message
–8–■To make a call1 Press or .2 Dial a telephone number.3 To hang up, press (OFF) or place the handset on the base unit.•If "No link to base. Walk closer to base and try again" isdisplayed and an alarm tone sounds in step 1, move closer to the base unitor place the handset on the base unit, and try again.•To redial the last number, press or , then press(PAUSE/REDIAL).•To adjust the receiver volume/speaker volume:To increase, press . To decrease, press .•To put a call on hold, press (HOLD/CLEAR).•To release the hold, press (HOLD/CLEAR).■To answer a callPress or .Making/Answering Calls with the Handset
–9–Making/Answering Calls with the Base Unit■To make a call1 Press (DIGITAL!SP-PHONE).2 Dial a telephone number.3 Talk into the MIC (microphone).4 To hang up, press (DIGITAL!SP-PHONE).•To redial the last number, press (DIGITAL!SP-PHONE), then press(REDIAL/PAUSE).•To adjust the speaker volume:To increase, press . To decrease, press .•To put a call on hold, press (HOLD).•To release the hold, press (DIGITAL!SP-PHONE).■To answer a callPress (DIGITAL!SP-PHONE), then talk into the MIC (microphone).Caller ID ServiceThis unit is compatible with a Caller ID service offered by your telephonecompany. After subscribing to a Caller ID service, the calling party’s information will beshown on the handset display after the first ring. The unit can record information of up to 30 different callers in the caller list.The Caller List information is sorted from the most recent to the oldest call.When the unit receives the 31st call, the oldest call is deleted.If your unit is connected to a PBX system which does not support Caller IDservices, you cannot access those services. Please consult your equipmentsupplier.
–10–Automatic Answering Operation■ How to use the mailboxesThe unit accommodates three mailboxes (Mailbox 1, 2 and 3). A caller canleave a message in a specified mailbox. If a mailbox is not specified,messages are recorded in the mailbox 1.■ When a caller callsThe caller can select a mailbox by pressing (#) and (1) (Mailbox 1), pressing(#) and (2) (Mailbox 2) or pressing (#) and (3) (Mailbox 3), while the greeting isplayed. The caller can then record a message in the mailbox after a beep.ORThe caller waits until the greeting finishes, and records a message after abeep. The message will be recorded in the Mailbox 1.■ Setting the unit to answer callsPress (ANSWER!ON) to turn on the answering system.•The indicator lights and “Answer set” is heard.Listening to MessagesYou can see the total number of recorded messages on the base unit display.If the ANSWER ON indicator flashes and the mailbox icon(s) ( ,and ) flash(es) on the display, new messages have been recorded inthe mailbox(es).To listen to the messages, press (MAILBOX!1), (MAILBOX!2) or (MAILBOX!3).•When you have new messages, the unit announces the number of newmessages and plays them back.•When you have no new messages, the unit plays back all recordedmessages.BOX 3BOX 2BOX 1
–11–Important Safety InstructionsWhen using this unit, basic safety precautions should always be followed toreduce the risk of fire, electric shock, or personal injury.11. Read and understand all instructions.12. Follow all warnings and instructions marked on this unit.13. Unplug this unit from AC outlets before cleaning. Do not use liquid oraerosol cleaners. Use a damp cloth for cleaning.14. Do not use this unit near water, for example, near a bathtub, washbowl,kitchen sink, or the like.15. Place this unit securely on a stable surface. Serious damage and/or injurymay result if the unit falls.16. Do not cover slots and openings on the unit. They are provided forventilation and protection against overheating. Never place the unit nearradiators, or in a place where proper ventilation is not provided.17. Use only the power source marked on the unit. If you are not sure of thetype of power supplied to your home, consult your dealer or local powercompany.18. Do not place objects on the power cord. Install the unit where no one canstep or trip on the cord.19. Do not overload wall outlets and extension cords. This can result in therisk of fire or electric shock.10. Never push any objects through slots in this unit. This may result in therisk of fire or electric shock. Never spill any liquid on the unit.11. To reduce the risk of electric shock, do not disassemble this unit. Take theunit to an authorized servicenter when service is required. Opening orremoving covers may expose you to dangerous voltages or other risks.Incorrect reassembly can cause electric shock when the unit issubsequently used.12. Unplug this unit from the wall outlet and refer servicing to an authorizedservicenter when the following conditions occur:A. When the power supply cord or plug is damaged or frayed.B. If liquid has been spilled into the unit.C. If the unit has been exposed to rain or water.D. If the unit does not work normally by following the operatinginstructions. Adjust only controls covered by the operating instructions.Improper adjustment may require extensive work by an authorizedservicenter.E. If the unit has been dropped or physically damaged.F. If the unit exhibits a distinct change in performance.13. During thunderstorms, avoid using telephones except cordless types.There may be a remote risk of an electric shock from lightning.14. Do not use this unit to report a gas leak, when in the vicinity of the leak.SAVE THESE INSTRUCTIONS
–12–CAUTION:To reduce the risk of fire or injury to persons, read and follow theseinstructions.1. Use only the battery(ies) specified.2. Do not dispose of the battery(ies) in a fire. They may explode. Check withlocal waste management codes for special disposal instructions.3. Do not open or mutilate the battery(ies). Released electrolyte is corrosiveand may cause burns or injury to the eyes or skin. The electrolyte may betoxic if swallowed.4. Exercise care in handling batteries in order not to short the battery toconductive materials such as rings, bracelets, and keys. The battery and/orconductor may overheat and cause burns.5. Charge the battery(ies) provided with or identified for use with this productonly in accordance with the instructions and limitations specified in thismanual.WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THISPRODUCT TO RAIN OR ANY TYPE OF MOISTURE. •The AC adaptor is used as the main disconnect device, ensure that the ACoutlet is located/installed near the unit and is easily accessible.
–13–FCC and Other InformationIf requested by the telephone company, inform them as follows:Registration No. .....................................................(found on the bottom of the unit)Ringer Equivalence ............................................................................................0.1BThe particular telephone line to which the equipment is connected.This unit must not be connected to a coin operated line.If you are on a party line, check with your local telephone company.Ringer Equivalence No. (REN):The REN is useful in determining the quantity of devices you may connect to yourtelephone line and still have all of those devices ring when your telephone number iscalled. In most, but not all areas, the sum of the REN’s of all devices connected to oneline should not exceed five (5.0). To be certain of the number of devices you mayconnect to your line, as determined by the REN, you should contact your localtelephone company to determine the maximum REN for your calling area. In the event terminal equipment causes harm to the telephone network, the telephonecompany should notify the customer, if possible, that service may be stopped.However, where prior notice is impractical, the company may temporarily cease serviceproviding that they:(a) Promptly notify the customer.(b) Give the customer an opportunity to correct the problem with their equipment.(c) Inform the customer of the right to bring a complaint to the Federal CommunicationCommission pursuant to procedures set out in FCC Rules and Regulations SubpartE of Part 68.The Telephone Company may make changes in its communications facilities,equipment, operations or procedures, where such action is reasonably required in theoperation of its business and is not inconsistent with the rules and regulations in 47CFR Part 68.If such changes can be reasonably expected to render any customer terminal equipmentincompatible with telephone company communications facilities, or require modification oralteration of such terminal equipment, or otherwise materially affect its use orperformance, the customer shall be given adequate notice in writing, to allow thecustomer an opportunity to maintain uninterrupted service.When programming emergency numbers and/or making test calls to emergencynumbers:1. Remain on the line and briefly explain to the dispatcher the reason for the callbefore hanging up.2. Perform such activities in the off-peak hours, such as early morning hours or lateevenings.This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that maycause undesired operation.Privacy of communications may not be ensured when using this phone.
–14–CAUTION:Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate this device.Note:This equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more of thefollowing measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.—Consult the dealer or an experienced radio/TV technician for help.Some cordless telephones operate at frequencies that may cause interference tonearby TVs and VCRs. To minimize or prevent such interference, the base of thecordless telephone should not be placed near or on top of a TV or VCR. If interferenceis experienced, move the cordless telephone further away from the TV or VCR. Thiswill often reduce, or eliminate, interference.Operating near 2.4GHz electrical appliances may cause interference. Move away fromthe electrical appliances.
–15–CAUTION:To comply with FCC RF exposure requirements, the base unit should be installed withits antenna located at 20 cm or more from persons and handset should be carried withthe specific belt-clip provided for the handset to ensure compliance. Other non-testedbelt-clips or similar body-worn accessories may not comply, therefore, should beavoided.This equipment is hearing aid compatible.A TIA/EIA-IS-968 compliant telephone cord and modular plug is provided with thisequipment. This equipment is designed to be connected to the telephone networkor premises wiring using a compatible modular jack that is also TIA/EIA-IS-968compliant.•Environment — do not place the unit in a room where the temperature is less than5°C (41°F) or greater than 40°C (104°F). Allow 10 cm (4") clearance around the unitfor proper ventilation. Avoid excessive smoke, dust, mechanical vibration, shock, ordirect sunlight.•Medical —consult the manufacturer of any personal medical devices, such aspacemakers, to determine if they are adequately shielded from external RF (radiofrequency) energy. (The unit operates in the frequency range of 2400MHz to2480MHz, and the power output level can range 0.04 watts to 0.40 watts.) Do not usethe unit in health care facilities if any regulations posted in the area instruct you not todo so. Hospitals or health care facilities may be using equipment that could besensitive to external RF (radio frequency) energy.•Routine care — wipe the unit with a soft cloth. Do not use benzine, thinner, or anyabrasive powder. When you leave the unit unused for a long period of time, unplugthe AC adaptor from the outlet.•If there is any trouble — disconnect the unit from the telephone line and connect aknown working phone. If the known working phone operates properly, have your unitrepaired by one of the authorized Panasonic Factory Service Centers. If the knownworking phone does not operate properly, consult your telephone company.
For product service•Call 1-800-211-PANA(7262) for the location of an authorized servicenter.•Panasonic’s e-mail address for customer inquiries:consumerproducts@panasonic.com for customers in the USA or Puerto Rico ONLYWhen you ship the product•Carefully pack your unit, preferably in the original carton.•Attach a letter, detailing the symptom, to the outside of the carton.Symptom•Send the unit to an authorized servicenter, prepaid and adequately insured.•Do not send your unit to the Panasonic Consumer Electronics Companylisted below or to executive or regional sales offices. These locations do notrepair consumer products.Panasonic Consumer Electronics Company,Division of Matsushita Electric Corporation of AmericaOne Panasonic Way, Secaucus, New Jersey 07094Panasonic Sales Company, Division of Matsushita Electric of Puerto Rico, Inc.Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park Carolina, Puerto Rico 00985

Navigation menu