Panasonic of North America 96NKX-TGA651 DECT Cordless Telephone Handset User Manual

Panasonic Corporation of North America DECT Cordless Telephone Handset

user manual

Thank you for purchasing a Panasonic product.Please read these operating instructions before using the unit and save them for future reference.This unit is compatible with Caller ID. You must subscribe to the appropriate service offered by your service provider/telephone company.For assistance, visit our website:http://www.panasonic.com/help for customers in the U.S.A. or Puerto Rico.Operating Instructions Expandable Digital Cordless Answering SystemModel shown is KX-TG6511.KX-TG6573KX-TG6531KX-TG6532KX-TG6533KX-TG6534 KX-TG6541 KX-TG6542KX-TG6543KX-TG6544 KX-TG6545Model No. KX-TG6521KX-TG6522 KX-TG6523 Expandable Digital Cordless PhoneModel No. KX-TG6511 KX-TG6512 KX-TG6513Before initial use, see "Getting Started" on page 5 .Please register your product: http://www.panasonic.com/prodreg
2For your safetyTo prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product.WARNINGPower connectionLUse only the power source marked on the product.LDo not overload power outlets and extension cords. This can result in the risk of fire or electric shock.LCompletely insert the AC adaptor/power plug into the power outlet. Failure to do so may cause electric shock and/or excessive heat resulting in a fire.LRegularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation defect from moisture, etc. resulting in a fire.LUnplug the product from power outlets if it emits smoke, an abnormal smell, or makes an unusual noise. These conditions can cause fire or electric shock. Confirm that smoke has stopped emitting and contact the Panasonic Call Center at 1-800-211-PANA (1-800-211-7262).LUnplug from power outlets and never touch the inside of the product if its casing has been broken open.LNever touch the plug with wet hands. Danger of electric shock exists.InstallationLTo prevent the risk of fire or electrical shock, do not expose the product to rain or any type of moisture.LDo not place or use this product near automatically controlled devices such as automatic doors and fire alarms. Radio waves emitted from this product may cause such devices to malfunction resulting in an accident.LDo not allow the AC adaptor or telephone line cord to be excessively pulled, bent or placed under heavy objects.Operating safeguardsLUnplug the product from power outlets before cleaning. Do not use liquid or aerosol cleaners.LDo not disassemble the product.LDo not spill liquids (detergents, cleansers, etc.) onto the telephone line cord plug, or allow it to become wet at all. This may cause a fire. If the telephone line cord plug becomes wet, immediately pull it from the telephone wall jack, and do not use.MedicalLConsult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. (The product operates in the frequency range of 1.92 GHz to 1.93 GHz, and the RF transmission power is 115 mW (max.).)LDo not use the product in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.CAUTIONInstallation and locationLNever install telephone wiring during an electrical storm.LNever install telephone line jacks in wet locations unless the jack is specifically designed for wet locations.LNever touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.LUse caution when installing or modifying telephone lines.LThe AC adaptor is used as the main disconnect device. Ensure that the AC outlet is installed near the product and is easily accessible.LThis product is unable to make calls when:– the handset batteries need recharging or have failed.– there is a power failure.
3BatteryLWe recommend using the batteries. USE ONLY rechargeable Ni-MH batteries AAA (R03) size.LDo not mix old and new batteries.LDo not open or mutilate the batteries. Released electrolyte from the batteries is corrosive and may cause burns or injury to the eyes or skin. The electrolyte is toxic and may be harmful if swallowed.LExercise care when handling the batteries. Do not allow conductive materials such as rings, bracelets, or keys to touch the batteries, otherwise a short circuit may cause the batteries and/or the conductive material to overheat and cause burns.LCharge the batteries provided with or identified for use with this product only, in accordance with the instructions and limitations specified in this manual.LOnly use a compatible base unit (or charger) to charge the batteries. Do not tamper with the base unit (or charger). Failure to follow these instructions may cause the batteries to swell or explode.Attention:A nickel metal hydride battery that is recyclable powers the product you have purchased.Please call 1-800-8-BATTERY (1-800-822-8837) for information on how to recycle this battery.Important safety instructionsWhen using your product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:1. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.3. Do not use the telephone to report a gas leak in the vicinity of the leak.4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.SAVE THESE INSTRUCTIONSFor best performanceBase unit location/avoiding noiseThe base unit and other compatible Panasonic units use radio waves to communicate with each other.LFor maximum coverage and noise-free communications, place your base unit:– at a convenient, high, and central location with no obstructions between the handset and base unit in an indoor environment.– away from electronic appliances such as TVs, radios, personal computers, wireless devices, or other phones.– facing away from radio frequency transmitters, such as external antennas of mobile phone cell stations. (Avoid putting the base unit on a bay window or near a window.)LCoverage and voice quality depends on the local environmental conditions.LIf the reception for a base unit location is not satisfactory, move the base unit to another location for better reception.EnvironmentLKeep the product away from electrical noise generating devices, such as fluorescent lamps and motors.LThe product should be kept free from excessive smoke, dust, high temperature, and vibration.LThe product should not be exposed to direct sunlight.LDo not place heavy objects on top of the product.
4LWhen you leave the product unused for a long period of time, unplug the product from the power outlet.LThe product should be kept away from heat sources such as heaters, kitchen stoves, etc. It should not be placed in rooms where the temperature is less than 0 °C (32 °F) or greater than 40 °C (104 °F). Damp basements should also be avoided.LThe maximum calling distance may be shortened when the product is used in the following places: Near obstacles such as hills, tunnels, underground, near metal objects such as wire fences, etc.LOperating the product near electrical appliances may cause interference. Move away from the electrical appliances.Routine careLWipe the outer surface of the product with a soft moist cloth.LDo not use benzine, thinner, or any abrasive powder.Other informationCAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.Notice for product disposal, transfer, or returnLThis product can store your private/confidential information. To protect your privacy/confidentiality, we recommend that you erase information such as phonebook or caller list entries from the memory before you dispose of, transfer, or return the product.NoticeENERGY STARAs an ENERGY STAR® Partner, Panasonic has determined that this product meets the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark.
Getting Started5Setting upConnectionsLUse only the supplied Panasonic AC adaptor PQLV219.■Base unit*DSL/ADSL filter (not supplied) is required if you have DSL/ADSL service. ■ChargerBattery installationLUSE ONLY Ni-MH batteries AAA (R03) size.LDo NOT use Alkaline/Manganese/Ni-Cd batteries.LConfirm correct polarities (S, T).Battery chargeCharge for about 7 hours.(120 V AC, 60 Hz)HooksRechargeable Ni-MH ONLYDSL/ADSL filter*Hook“Click”Press plug firmly.Correct Wrong(120 V AC, 60 Hz)To single-line telephone jack (RJ11C)“Click”LWhen the batteries are fully charged, the charge indicator goes off.Confirm "Charging" is displayed.Charge indicator
Getting Started6Note when setting upNote for connectionsLThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)LThe AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected.During a power failureThe unit will not work during a power failure. We recommend connecting a corded-type telephone (without AC adaptor) to the same telephone line or to the same telephone line jack using a Panasonic T-adaptor. Emergency power can be supplied to the unit by connecting a Panasonic battery back-up power supply.Note for battery installationLUse the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries. LWipe the battery ends (S, T) with a dry cloth.LAvoid touching the battery ends (S, T) or the unit contacts.Note for battery chargeLIt is normal for the handset to feel warm during charging.LClean the charge contacts of the handset, base unit, and charger with a soft and dry cloth once a month. Clean more often if the unit is exposed to grease, dust, or high humidity.Battery levelNote:LThe batteries need to be charged if the handset beeps while you are engaged in a call or operating the answering system remotely.Panasonic Ni-MH battery performance (supplied batteries)Icon Battery level&High(Medium)Low0)4Needs charging.0EmptyOperation Operating timeIn continuous use5 hours max.*1Not in use (standby)11 days max.*1 When the clarity booster feature is turned on: 3 hours max.Note:LActual battery performance depends on a combination of how often the handset is in use and how often it is not in use (standby).LEven after the handset is fully charged, the handset can be left on the base unit or charger without any ill effect on the batteries.LThe battery level may not be displayed correctly after you replace the batteries. In this case, place the handset on the base unit or charger and let it charge for at least 7 hours.
Getting Started7ControlsBase unit■KX-TG6511 series ACharge contactsB{LOCATOR}CBracket■KX-TG6521/KX-TG6531 series ACharge contactsBSpeakerC{ERASE}D{■} (STOP)E{^}/{V} (VOL.: Volume up/down){7}/{8} (Repeat/Skip)F{6} (Play) Message indicatorG{LOCATOR}H{ANSWER ON} ANSWER ON indicatorIBracket A BCDC E F G HIA B
Getting Started8ACharge contactsBSpeakerC{■} (STOP)D{ERASE}E{^}/{V} (VOL.: Volume up/down){7}/{8} (Repeat/Skip)F{6} (Play) Message indicatorG{ANSWER ON} ANSWER ON indicatorH{LOCATOR} {INTERCOM}I MicrophoneJDial keypad ({*}: TONE)K{REDIAL} {PAUSE}L{HOLD}M{SP-PHONE} (Speakerphone)SP-PHONE indicatorN{FLASH} {CALL WAIT}O{MUTE}P{CONF} (Conference)Q{MEMO}RBracketHandset (KX-TGA652)ACharge indicatorRinger indicatorMessage indicatorBNon-slip padLNon-slip pad offers support when you cradle the handset between your shoulder and ear.CSpeakerD{C} (TALK)E{s} (SP-PHONE: Speakerphone)FHeadset jack (KX-TG6511/KX-TG6531/KX-TG6541 series) GDial keypad ({*}: TONE)HReceiverIDisplayB CMAGFDEJKIHLAB■KX-TG6541 series ABCDEFG HNJOPQRIKLM
Getting Started9J{OFF}K{FLASH} {CALL WAIT}LMicrophoneMCharge contacts■Control typeA Soft keysThe handset features 3 soft keys. By pressing a soft key, you can select the feature shown directly above it on the display.B Navigator key –? VOL. (Volume: {^} or {V}): You can adjust the receiver or speaker volume while talking.– {<} CID:You can enter the caller list.{>} REDIAL:You can enter the redial list. – {^}, {V}, {<}, or {>}: You can scroll through various lists or items.–
10Making callsUsing the handset1Lift the handset and dial the phone number.LTo correct a digit, press {CLEAR}.2Press {C} or {CALL}.3When you finish talking, press {OFF} or place the handset on the base unit or charger.Using the speakerphone1Dial the phone number and press {s}.LSpeak alternately with the other party.2When you finish talking, press {OFF}.Note:LFor best performance, use the speakerphone in a quiet environment.LTo switch back to the receiver, press {C}.Adjusting the receiver or speaker volumePress {^} or {V} repeatedly while talking.Making a call using the redial listThe last 5 phone numbers dialed are stored in the redial list (each 48 digits max.).1{REDIAL}2{V}/{^}: Select the desired phone number.3{C}Using the base unit1{SP-PHONE}2Dial the phone number.3When the other party answers, speak into the MIC.LSpeak alternately with the other party.4When you finish talking, press {SP-PHONE}.Note:LUse the speakerphone in a quiet environment.Available for:KX-TG6541 series LWhile on a call, you can switch from the base unit to the handset:– Press {C} on the handset, then press {SP-PHONE} on the base unit.– If the handset is on the base unit, simply lift it.Adjusting the speaker volumePress {^} or {V} repeatedly while talking.Redialing the last number dialed{SP-PHONE} i {REDIAL}
11Answering callsUsing the handsetWhen a call is being received, the ringer indicator flashes rapidly.1Lift the handset and press {C} or {s} when the unit rings.LYou can also answer the call by pressing any dial key from {0} to {9}, {*}, or {#}. (Any key answer feature)2When you finish talking, press {OFF} or place the handset on the base unit or charger.Auto talkYou can answer calls simply by lifting the handset off the base unit or charger. You do not need to press {C}. To turn this feature on.Adjusting the handset ringer volumePress {^} or {V} repeatedly to select the desired volume while the handset is ringing for an incoming call.Note:LYou can also program the handset ringer volume beforehand.Temporary handset ringer offWhile the handset is ringing for a call, you can turn the ringer off temporarily by pressing {~}.Adjusting the base unit ringer volumePress {^} or {V} repeatedly to select the desired volume.LTo turn the ringer off, press and hold {V} until the unit beeps 2 times.Note:LWhen the ringer volume is set to off, the base unit rings at the low level for intercom calls. (KX-TG6541 series)Using the base unitWhen a call is being received, the SP-PHONE indicator flashes rapidly.1Press {SP-PHONE} when the unit rings.2Speak into the MIC.3When you finish talking, press {SP-PHONE}.Available for:KX-TG6521/KX-TG6531/KX-TG6541 series Available for:KX-TG6541 series
12Shared phonebookThe shared phonebook allows you to make calls without having to dial manually. Any handset registered to the base unit can use the shared phonebook. You can add 50 names and phone numbers to the shared phonebook, and assign each phonebook entry to the desired category.Important:LOnly 1 person can access the shared phonebook at a time.LCaller ID subscribers can use group ringer tone features.Adding entries1{C}2{ADD}3Enter the party’s name (16 characters max.). i {OK}4Enter the party’s phone number (24 digits max.). i {OK}5{V}/{^}: Select the desired group. i {SELECT} 2 timesLTo add other entries, repeat from step 2.6{OFF}Character table for entering namesWhile entering characters, you can switch between uppercase and lowercase by pressing {*}.LTo enter another character that is located on the same dial key, first press {>} to move the cursor to the next space.Note:LIf you do not press any dial key within 5 seconds after entering a character, the character is fixed and the cursor moves to the next space.Correcting a mistakePress {<} or {>} to move the cursor to the character or number you want to erase, then press {CLEAR}. Enter the appropriate character or number.LPress and hold {CLEAR} to erase all characters or numbers.Key Character{1}&’ ( ) ;,–./1{2}ABC2abc2{3}DEF3def 3{4}GHI 4ghi 4{5}JKL5jkl5{6}MNO6mn o 6{7}PQRS7pqrs7{8}TUV8tuv8{9}WX Y Z 9wx yz9{0}Space 0{#} #
13Finding and calling a phonebook entryScrolling through all entries1{C}2{V}/{^}: Select the desired entry.3{C}Searching by first character1{C}2Press the dial key ({0} – {9}, {*}, or {#}) which contains the character you are searching for. LPress the same dial key repeatedly to display the first entry corresponding to each character located on that dial key.LIf there is no entry corresponding to the character you selected, the next entry is displayed.3{V}/{^}: Scroll through the phonebook if necessary.4{C}Registering a unitOperating additional unitsAdditional handsetsUp to 6 handsets can be registered to the base unit.Registering a handset to the base unitThe supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset.1Handset:{MENU} i {#}{1}{3}{0}2Base unit:Press and hold {LOCATOR} for about 4 seconds until the registration tone sounds.LIf all registered handsets start ringing, press the same button to stop. Then repeat this step.LThe next step must be completed within 90 seconds.3Handset:Press {OK}, then wait until a long beep sounds.4{OFF}Press and hold {LOCATOR} for about 4 seconds. (No registrationtone)■KX-TG6511 series■KX-TG6521/KX-TG6531/KX-TG6541 series
14Using Caller ID serviceImportant:LThis unit is Caller ID compatible. To use Caller ID features, you must subscribe to a Caller ID service. Contact your service provider/telephone company for details.Caller ID featuresWhen an outside call is being received, the caller’s name and phone number are displayed.Caller information for the last 50 callers is logged in the caller list from the most recent call to the oldest.LIf the unit cannot receive caller information, the following is displayed:–“Out of area”: The caller dials from an area which does not provide a Caller ID service.–“Private caller”: The caller requests not to send caller information.–“Long distance”: The caller makes a long distance call.LIf the unit is connected to a PBX system, caller information may not be properly received. Contact your PBX supplier.
15Answering systemThe answering system can answer and record calls for you when you are unavailable to answer the phone.You can also set the unit to play a greeting message but not to record caller messages by selecting “Greeting only” as the recording time setting.Important:LOnly 1 person can access the answering system (listen to messages, record a greeting message, etc.) at a time.LWhen callers leave messages, the unit records the day and time of each message. Make sure the date and time have been set correctly. Turning the answering system on/offPress {ANSWER ON} to turn on/off the answering system.■To turn on:1{MENU} i {#}{3}{2}{7}2{OFF}■To turn off:1{MENU} i {#}{3}{2}{8}2{OFF}Note for base unit and handset:LWhen the answering system is turned on, the ANSWER ON indicator on the base unit lights up.Available for:KX-TG6521/KX-TG6531/KX-TG6541 series Base unitHandsetGreeting messageWhen the unit answers a call, a greeting message is played to callers.You can use either:– your own greeting message– a pre-recorded greeting messageRecording your greeting message1{MENU} i {#}{3}{0}{2}2{V}/{^}: “Yes” i {SELECT}3After a beep sounds, speak clearly (2 minutes and 30 seconds max.).4Press {STOP} to stop recording.5{OFF}Listening to messages using the base unitWhen new messages have been recorded, the message indicator on the base unit flashes.Press {6}.LIf new messages have been recorded, the base unit plays back new messages.LIf there are no new messages, the base unit plays back all messages.
16FCC and other informationThis equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:ACJ----------.If requested, this number must be provided to the telephone company.L Registration No.............(found on the bottom of the unit)L Ringer Equivalence No. (REN).......0.1BA plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with the product. It is designed to be connected to a compatible modular jack that is also compliant.The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for the product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.If trouble is experienced with this equipment, for repair or warranty information, please contact a Factory Service Center or other Authorized Servicer. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section 68.316.When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If noise occurs, use an optional headset accessory or the speakerphone option (if applicable) when using this phone. Consult with your audiologist or Hearing Aid manufacturer about the availability of Hearing Aids which provide adequate shielding to RF energy commonly emitted by digital devices.
17WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:1) Remain on the line and briefly explain to the dispatcher the reason for the call.2) Perform such activities in the off-peak hours, such as early morning or late evenings.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Privacy of communications may not be ensured when using this phone.CAUTION:Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the equipment and receiver.– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.– Consult the dealer or an experienced radio/TV technician for help.Some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, move the cordless telephone further away from the TV or VCR. This will often reduce, or eliminate, interference.FCC RF Exposure Warning:L This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. L To comply with FCC RF exposure requirements, the base unit must be installed and operated 20 cm (8 inches) or more between the product and all person’s body (excluding extremities of hands, wrist and feet). L This product may not be collocated or operated in conjunction with any other antenna or transmitter.L The handset may be carried and operated with only the specific provided belt-clip. Other non-tested belt-clips or similar body-worn accessories may not comply and must be avoided.NoticeL FCC ID can be found inside the battery compartment or on the bottom of the units. Compliance with TIA-1083 standard: Telephone handsets identified with this logo have reduced noise and interference when used with T-Coil equipped hearing aids and cochlear implants.TCompatible withHearing Aid T-CoilTIA-1083
For your future referenceWe recommend keeping a record of the following information to assist with any repair under warranty.Copyright:This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd.© Panasonic Communications Co., Ltd. 2009Serial No. Date of purchase(found on the bottom of the base unit)Name and address of dealer1 Reconnect AC adaptor to the base unit.2 Check if telephone line cord is connected.3 Use rechargeable Ni-MH batteries. (Alkaline/Manganese/Ni-Cd batteries CANNOT be used.)4 Read troubleshooting page in the Operating Instructions.If your product is not working properly. . .IMPORTANT!Visit our Web site: http://www.panasonic.com/helpLFAQ and troubleshooting hints are available.Attach your purchase receipt here.One Panasonic Way, Secaucus, New Jersey 07094

Navigation menu