Panasonic of North America 9TGBT12B Bluetooth Module User Manual
Panasonic Corporation of North America Bluetooth Module
User Manual
Bluetooth Module: BT12B
User Manual
1 G
E
1-1
P
This
whic
h
This
Reli
a
1-2
S
Item
s
2-1
S
E
NERAL
P
urpose an
d
document
c
h
comply wi
t
document
s
a
bility specif
i
S
tandard O
p
s
Conditio
n
S
pecificati
o
d
Scope of
c
ontains the
t
h BLUETO
s
pecifies an
d
i
cations an
d
p
erating C
o
n
s
o
ns
this docu
m
specificatio
O
TH™ Spe
d
describes
d
aspects fo
r
o
nditions
m
ent
ns pertinen
t
cifications
V
General, M
e
r
Panasoni
c
t
to the mod
V
ersion 4.0.
e
chanical,
E
c
Bluetooth
M
u
le for Blue
t
E
lectrical, S
o
M
odule BT1
2
t
ooth™ sys
t
o
ftware and
2
B.
t
em,
Regulatory Information
USA-Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Labeling
System integrators must include the FCC ID on the label of the end product as
following, “Contains FCC ID: ACJ9TGBT12B”.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC/IC RF exposure compliance requirements, a separation
distance of at least 20 cm must be maintained between the antenna of this
device and all persons. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating
requirements and conditions that must be observed to ensure compliance with
the above-mentioned FCC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy FCC RF Exposure
requirements.
The antenna used this module is as follows;
Antenna Type: PIFA
Antenna Gain: -0.48dBi
If an antenna with higher gain or new antenna type is used with this module,
integrators must contact Panasonic for additional testing and submission to the
FCC.
If other radio devices are to be integrated with this module, an additional
evaluation and FCC submission may be required. Integrators are responsible for
such additional evaluation and FCC submission.
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of this device.
L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Caution: Exposure to Radio Frequency Radiation.
To comply with RSS 102 RF exposure compliance requirements, for mobile
configurations, a separation distance of at least 20 cm must be maintained
between the antenna of this device and all persons. This device must not be
co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux rayonnements
énoncées pour un environnement non contrôlé et respecte les règles
d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet
équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus
entre le dispositif rayonnant et le corps.
Labeling
System integrators must include the IC ID on the label of end product as
following, “Contains IC: 216A-CFBT12B”.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating
requirements and conditions that must be observed to ensure compliance with
the above-mentioned FCC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy FCC RF Exposure
requirements.
The antenna used this module is as follows;
Antenna Type: PIFA
Antenna Gain: -0.48dBi
If an antenna with higher gain or new antenna type is used with this module,
integrators must contact Panasonic for additional testing and submission to the
FCC.
If other radio devices are to be integrated with this module, an additional
evaluation and FCC submission may be required. Integrators are responsible for
such additional evaluation and FCC submission.