Panasonic of North America 9TGBT12B Bluetooth Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1756997
Application ID	6DS6w+DGeaY2zaPqMPjXqg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.48kB (168490 bits)
Date Submitted	2012-07-31 00:00:00
Date Available	2012-09-14 00:00:00
Creation Date	2012-07-30 10:21:03
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2012-07-30 10:21:03
Document Title	User Manual
Document Creator	PScript5.dll Version 5.2.2

Bluetooth Module: BT12B
User Manual
1 GE
ENERAL
1-1 P
Purpose and
d Scope of this docum
ment
This document contains
the specificatio ns pertinentt to the module for Bluettooth™ systtem,
h comply witth BLUETOOTH™ Spe cifications Version
4.0.
which
This document specifies
and
d describes General, Me
echanical, Electrical,
Sooftware and
ability specifiications and
d aspects forr Panasonic
c Bluetooth Module
BT122B.
Relia
1-2 S
Standard Op
perating Co
onditions
Items
s Condition
ns
Specificatio
ons
2-1 S
Regulatory Information
USA-Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Labeling
System integrators must include the FCC ID on the label of the end product as
following, “Contains FCC ID: ACJ9TGBT12B”.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC/IC RF exposure compliance requirements, a separation
distance of at least 20 cm must be maintained between the antenna of this
device and all persons. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating
requirements and conditions that must be observed to ensure compliance with
the above-mentioned FCC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy FCC RF Exposure
requirements.
The antenna used this module is as follows;
Antenna Type: PIFA
Antenna Gain: -0.48dBi
If an antenna with higher gain or new antenna type is used with this module,
integrators must contact Panasonic for additional testing and submission to the
FCC.
If other radio devices are to be integrated with this module, an additional
evaluation and FCC submission may be required. Integrators are responsible for
such additional evaluation and FCC submission.
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of this device.
L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Caution: Exposure to Radio Frequency Radiation.
To comply with RSS 102 RF exposure compliance requirements, for mobile
configurations, a separation distance of at least 20 cm must be maintained
between the antenna of this device and all persons. This device must not be
co-located or operating in conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux rayonnements
énoncées pour un environnement non contrôlé et respecte les règles
d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet
équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus
entre le dispositif rayonnant et le corps.
Labeling
System integrators must include the IC ID on the label of end product as
following, “Contains IC: 216A-CFBT12B”.
Instructions to OEM Integrators
A User manual provided to the end user must indicate the operating
requirements and conditions that must be observed to ensure compliance with
the above-mentioned FCC RF Exposure guideline.
If this module is intended for use in a portable device, integrators are responsible
for separate evaluation and/or approval to satisfy FCC RF Exposure
requirements.
The antenna used this module is as follows;
Antenna Type: PIFA
Antenna Gain: -0.48dBi
If an antenna with higher gain or new antenna type is used with this module,
integrators must contact Panasonic for additional testing and submission to the
FCC.
If other radio devices are to be integrated with this module, an additional
evaluation and FCC submission may be required. Integrators are responsible for
such additional evaluation and FCC submission.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : 
Create Date                     : 2012:07:30 10:21:03+09:00
Modify Date                     : 2012:07:30 10:21:03+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Creator                         : 
Title                           : 
Document ID                     : uuid:ff1836e0-af9c-466b-b4a9-e543d2861ace
Instance ID                     : uuid:0f91c3d4-a459-4626-9210-0465bdd7b0fe
Page Count                      : 5

EXIF Metadata provided by EXIF.tools