Panasonic of North America 9TGCF-082 Panasonic Toughbook with WLAN and Bluetooth User Manual CF 08

Panasonic Corporation of North America Panasonic Toughbook with WLAN and Bluetooth CF 08

Draft Users Manual

Read Me FirstPlease read these instructions carefully before using this product and save this manual for future use.EDFWireless DisplayModel No. CF-08Read Me First ..................................................................................2ENGLISH OPERATING INSTRUCTIONSContents ........................................................................................13DEUTSCH BEDIENUNGSANLEITUNGInhalt ..............................................................................................61FRANÇAIS INSTRUCTIONS D’UTILISATIONSommaire.....................................................................................110
2Read Me FirstRead Me FirstFederal Communications Commis-sion Radio Frequency Interference StatementNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec-tion against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-ence to radio communications. How-ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to cor-rect the interference by one or more of the following measures:zReorient or relocate the receiving antenna.zIncrease the separation between the equipment and receiver.zConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.zConsult the Panasonic Service Cen-ter or an experienced radio/TV tech-nician for help.WarningTo assure continued compliance, use only shielded interface cables when connecting to a wireless display or peripheral. Also, any changes or modi-fications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interfer-ence received, including interference that may cause undesired operation.Responsible Party:Panasonic Corporation of North AmericaOne Panasonic Way Secaucus, NJ 07094Tel No:1-800-LAPTOP5 (1-800-527-8675)FCC RF Exposure Warning:zThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.zThis equipment must be installed and operated in accordance with provided instructions and minimum 1.5 cm spacing must be provided between antenna and all person’s body (excluding extremities of hands, wrist and feet) during wire-less modes of operation.zThis transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Models for U.S.A.
3Read Me FirstNotice for the products using LCDThis product uses one or more fluores-cent lamps containing a small amount of mercury. It also contains lead in some components. Disposal of these materi-als may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org/>For Use in Motor VehicleWarning: Wireless display may be installed in a motor vehicle and visible to the driver only if used to support vehicle related functions such as vehicle infor-mation, system control, rear or side observation and navigation. If used for entertainment purpose, such as televi-sion reception or video play, it must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.Check with individual state/provincial laws to determine lawful use of this product while operating within a motor vehicle.Pour L’utilisation Dans Un Véhicule MotoriséAvertissement : L’ordinateur bloc-notes peut être installé dans un véhicule motorisé et dans le champ de vision du conducteur uniquement en tant que dis-positif d’aide aux fonctions du véhicule, comme par exemple pour fournir des informations sur le véhicule, comme dis-positif de contrôle de système, pour l’observation à l’arrière ou sur les côtés du véhicule, ainsi que pour fournir de l’information routière. Pour toute utilisa-tion à fin de divertissement, comme par exemple pour regarder la télévision ou jouer à des jeux vidéo, il doit être installé à l’arrière du siège du conduc-teur, en un emplacement où il ne sera pas visible, ni directement ni indirecte-ment, pour le conducteur du véhicule motorisé. Vérifiez les lois fédérales et nationales qui régissent l’utilisation légale de cet appareil à l’intérieur d’un véhicule motorisé.Models for U.S.A./CanadaModels for CanadaIndustry CanadaThis product complies with RSS210 Industry Canada.Operation is subject to the following two conditions;(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device.
4Read Me FirstRead Me FirstWarningThis apparatus must be earthed for your safety.To ensure safe operation the three-pin plug must be inserted only into a stan-dard three-pin power point which is effectively earthed through the normal household wiring.Extension cords used with the equip-ment must be threecore and be cor-rectly wired to provide connection to earth. Wrongly wired extension cords are a major cause of fatalities.The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe.For your safety, if you have any doubt about the effective earthing of the power point, consult a qualified electrician.FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLYThis appliance is supplied with a moul-ded three pin mains plug for your safety and convenience.A 3 amp fuse is fitted in this plug.Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 3 amps and that it is approved by ASTA or BSI to BS 1362.Check for the ASTA mark or the BSI mark on the body of the fuse.If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.If you lose the fuse cover the plug must not be used until a replacement cover is obtained.A replacement fuse cover can be pur-chased from your local Panasonic Dealer.IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.If a new plug is to be fitted please observe the wiring code as shown below.If in any doubt please consult a qualified electrician.Warning: THIS APPLIANCE MUST BE EARTHED.ImportantThe wires in this mains lead are coloured in accordance with the follow-ing code:Green-and-yellow: EarthBlue: NeutralBrown: LiveAs the colours of the wires in the mains lead of this apparatus may not corre-spond with the coloured markings iden-tifying the terminals in your plug, proceed as follows:The wire which is coloured GREEN-and-YELLOW must be connected to the Models for U.K. A S A
5Read Me Firstterminal in the plug which is marked by the letter E or by the safety earth sym-bol coloured GREEN or GREEN-and-YELLOW.The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured BLACK.The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured RED.The mains plug on this equipment must be used to disconnect the mains power.Please ensure that a socket outlet is available near the equipment and shall be easily accessible.How to replace the fuseOpen the fuse compart-ment with a screwdriver and replace the fuse.WarningszThis equipment is not designed for connection to an IT power system.(An IT system is a system having no direct connections between live parts and Earth; the exposed-conducive-parts of the electrical installation are earthed. An IT system is not permit-ted where the wireless display is directly connected to public supply systems in the U.K.)zDisconnect the mains plug from the supply socket when the wireless dis-play is not in use.This equipment is produced to BS800/1983.For Use in Motor VehicleWarning: Check the following Commis-sion Recommendation to determine proper installation and usage of this product while operating within a motor vehicle. "Commission Recommenda-tion on safe and efficient in-vehicle infor-mation and communication systems: A European statement of principles on human machine interface."Commission Recommendation is avail-able from Official Journal of the Euro-pean Communities.
6Read Me FirstRead Me FirstZur Verwendung in FahrzeugenWarnung: Überprüfen Sie die folgende Empfehlung der EUKommission, um die richtige Installation und Verwendung dieses Produktes zu ermitteln, wenn Sie das Gerät in einem Fahrzeug betreiben möchten.“Empfehlung der Kommission an die Mitgliedsstaaten und die Industrie über sichere und effiziente On-board-Informations- und -Kommunikationssysteme: Europäischer Grundsatzkatalog zur Mensch-Maschine-Schnittstelle.”Die Empfehlung der EU-Kommission steht im offiziellen Journal der EU zur Verfü-gung.Bande de fréquences restreinte: Lors de l’utilisation de cet appareil sur le territoire français, vous ne pouvez le faire qu’en utilisant les bandes de fréquences 10 et 11 (respectivement 2.457 MHz et 2.462 MHz). L’utilisation de cet appareil sur une autre bande prise en charge par celui-ci est interdite. Une utilisation à l’extérieur n’est pas autorisée.L’utilisation de Bluetooth est interdite pour les communications extérieures.N’utilisez pas la technologie Bluetooth à l’extérieur.Utilisation dans un véhicule automobileDanger: Vérifiez les recommandations de la Commission Européenne suivantes pour une installation et une utilisation adéquates de ce produit dans un véhicule automobile.“Recommandation de la Commission sur les systèmes efficaces d’information et de communication embarqués dans les véhicules et garantissant une séurité opti-male: délaration de principes européenne concernant l’interface homme/machine.” Les recommandations de la Commission Européenne sont disponibles dans le Journal Officiel des Communautés Européennes.A S AThis product and your HealthThis product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this product however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.Für DeutschlandPour la FranceInformation to the User
7Read Me FirstBecause this product operates within the guidelines found in radio frequency safety standards and recommendations, we believe this product is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of sci-entists who continually review and interpret the extensive research literature.In some situations or environments, the use of this product may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:zUsing this product on board of airplanes, orzIn any other environment where the risk of interference to other devices or ser-vices is perceived or identified as harmful.If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use this product prior to turning on the product.Regulatory InformationWe are not responsible for any radio or television interference caused by unautho-rized modification of this product. The correction of interference caused by such unauthorized modification will be the responsibility of the user. We and its autho-rized resellers or distributors are not liable for damage or violation of government regulations that may arise from failing to comply with these guidelines.Declaration of Conformity (DoC)“Hereby, we declare that this wireless display is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.”Hint:If you want to get a copy of the original DoC of our products which relates to the R&TTE, please contact to our web address: http://www.doc.panasonic.deContact:Panasonic Services EuropeA Division of Panasonic Marketing Europe GmbHPanasonic Testing Centre-------------------------------------------------------------------------------------------------------------Compliance Notice - CE MarkThis equipment is in conformance with the requirements of the European Council Directive listed below:73/23/EEC Low Voltage Directive with amendment 93/68/EEC89/336/EEC EMC Directive with amendments 92/31/EEC and 93/68/EEC1999/5/EC R&TTE-------------------------------------------------------------------------------------------------------------
8Read Me FirstRead Me FirstInformation on Disposal for Users of Waste Electrical & Electronic Equip-ment (private households)This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.Please dispose of this item only in designated national waste elec-tronic collection schemes, and not in the ordinary dust bin.For business users in the European UnionIf you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.Information on Disposal in other Countries outside the European UnionThis symbol is only valid in the European Union.If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
9Read Me First-Dieses Produkt und Ihre GesundheitWie andere Funkgeräte strahlt auch dieses Produkt elektromagnetische Funkfre-quenzenergie ab. Die Strahlung ist allerdings weit weniger stark als bei drahtlosen Geräten wie beispielsweise einem Handy.Da sich dieses Produkt im Rahmen der Richtlinien bewegt, die für Funkfrequenz-Sicherheitsstandards und Empfehlungen Geltung haben, gehen wir davon aus, dass es gefahrlos von Verbrauchern eingesetzt werden kann.Diese Standards und Empfehlungen spiegeln den Konsensus der wissenschaftli-chen Gemeinschaft wider und sind das Ergebnis der Arbeit von Sachverständigen und wissenschaftlichen Ausschüssen, welche sich laufend mit der einschlägigen Fachliteratur und den Forschungsresultaten auseinandersetzen.Es kann Fälle geben, in denen der Eigentümer eines Gebäudes oder der Zustän-dige einer Organisation den Einsatz dieses Produkts in einer bestimmten Situation oder Umgebung einschränkt oder untersagt. Dazu können zählen:zBenutzung dieses Produktes in Flugzeugen oderzIn jeder anderen Umgebung, in der die Gefahr von Störungen anderer Geräte oder Dienste vermutet oder erkannt wurde.Sollten Sie nicht sicher sein, welche Richtlinien und Vorschriften für den Gebrauch von drahtlosen Geräten innerhalb einer bestimmten Organisation oder Umgebung (z. B. in Flughäfen) gelten, empfehlen wir Ihnen, sich vor dem Einschalten des Gerätes entsprechend zu informieren und gegebenenfalls eine Genehmigung einzuholen.RegulierungsinformationWir sind in keiner Weise verantwortlich für Störungen des Funkverkehrs oder von Fernsehgeräten, die durch eigenmächtige Änderungen an diesem Produkt verursacht werden. Die Beseitigung solcher, durch unbefugte Änderungen verursachten, Störungen obliegt der alleinigen Verantwortlichkeit des Benutzers. Weder wir noch unsere autorisierten Händler und Verkäufer können für Schäden oder für die Verletzung von gesetzlichen Vorschriften haftbar gemacht werden, die durch die Zuwiderhandlung gegen diese Richtlinien entstehen.Herstellererklärungen (DoC)“Wir erklären hiermit, daß dieser Personalcomputer mit den not-wendigen Anforderungen und anderen relevanten Bedingungen der Direktive 1999/5/EC übereinstimmt.”Hinweis:Falls Sie einen Kopie der ursprünglichen Herstellererklärungen unserer Produkte erhalten möchten, die sich auf R&TTE bezieht, besuchen Sie bitte unsere Web-Adresse: http://www.doc.panasonic.deKontakt:Anwenderinformation
10Read Me FirstRead Me FirstPanasonic Services EuropeA Division of Panasonic Marketing Europe GmbHPanasonic Testing Centre-------------------------------------------------------------------------------------------------------------Übereinstimmungserklärung - CE-MarkeDiese Ausrüstung erfüllt die Anforderungen der unten angegebenen EC-Direktive:73/23/EEC Niederspannungsdirektive mit Abänderung 93/68/EEC89/336/EEC EMC-Direktive mit Abänderungen 92/31/EEC und 93/68/EEC1999/5/EC R&TTE-------------------------------------------------------------------------------------------------------------Benutzerinformationen zur Entsorgung von elektrischen und elektronischenGeräten (private Haushalte)Entsprechend der grundlegenden Firmengrundsätzen der Pana-sonic-Gruppe wurde ihr Produkt aus hochwertigen Materialien und Komponenten entwickelt und hergestellt, die recycelbar und wieder verwendbar sind.Dieses Symbol auf Produkten und/oder begleitenden Dokumenten bedeutet, dass elektrische und elektronische Produkte am Ende ihrer Lebensdauer vom Hausmüll getrennt entsorgt werden müssen.Bringen Sie bitte diese Produkte für die Behandlung, Rohstoffrückgewinnung und Recycling zu den eingerichteten kommunalen Sammelstellen bzw.Wertstoffsammelhöfen, die diese Geräte kostenlos entgegennehmen.Die ordnungsgemäße Entsorgung dieses Produkts dient dem Umweltschutz und verhindert mögliche schädliche Auswirkungen auf Mensch und Umwelt, die sich aus einer unsachgemäßen Handhabung der Geräte am Ende Ihrer Lebensdauer ergeben könnten.Genauere Informationen zur nächstgelegenen Sammelstelle bzw. Recyclinghof erhalten Sie bei Ihrer Gemeindeverwaltung.Für Geschäftskunden in der Europäischen UnionBitte treten Sie mit Ihrem Händler oder Lieferanten in Kontakt, wenn Sie elek-trische und elektronische Geräte entsorgen möchten. Er hält weitere Informa-tionen für sie bereit.Informationen zur Entsorgung in Ländern außerhalb der Europäischen UnionDieses Symbol ist nur in der Europäischen Union gültig.
11Read Me FirstCe produit et votre santéCe produit, comme tout autre appareil radio, émet de l’énergie radioélectrique. Toutefois, la quantité d’énergie émise par ce produit est beaucoup moins impor-tante que l’énergie radioélectrique émise par des appareils sans fil tels que les téléphones portables.L’utilisation de ce produit ne comporte aucun risque pour le consommateur du fait que cet appareil opère dans les limites des directives concernant les normes et les recommandations de sécurité sur les fréquences radio. Ces normes et recomman-dations reflètent le consensus de la communauté scientifique et résultent de délibérations de jurys et comités de scientifiques qui examinent et interprètent con-tinuellement les nouveautés de la vaste littérature sur les recherches effectuées.Dans certaines situations ou environnements, l’utilisation de ce produit peut être restreinte par le propriétaire du bâtiment ou par les représentants responsables de l’organisation. Ces situations peuvent être les suivantes par exemple :zÀ bord d’un avion, ouzDans tout autre environnement où les risques d’interférence sur d’autres appa-reils ou services sont perçus ou identifiables comme dangereux.Si vous n’êtes pas sûr de la réglementation applicable à l’utilisation d’appareils sans fil dans une organisation ou un environnement spécifiques (par exemple dans un aéroport), nous vous invitons à demander l’autorisation d’utiliser ce pro-duit avant sa mise en marche.Informations concernant la réglementationNous déclinons toute responsabilité pour toute interférence radio ou télévision causée par des modifications non autorisées apportées à ce produit. La correction d’interférences causées par de telles modifications non autorisées sera la seule responsabilité de son utilisateur. Nous-mêmes, les revendeurs officiels et les dis-tributeurs ne sommes pas responsable de tout dégât ou de toute violation des règlements de l’État pouvant découler du non-respect de ces directives.Déclaration de conformité (DoC)Par présent document nous déclarons que cet ordinateur est con-forme aux conditions fondamentales et aux autres dispositions applicables de la Directive 1999/5/EC.Suggestion:Si vous voulez obtenir une copie de la DoC d’origine de nos produits qui concerne le R&TTE, veuillez contacter notre site Internet à l’adresse:http://www.doc.panasonic.deInformations destinées aux utilisateurs
12Read Me FirstRead Me FirstContact:Panasonic Services EuropeA Division of Panasonic Marketing Europe GmbHPanasonic Testing Centre-------------------------------------------------------------------------------------------------------------Avis de comformité - Marque CECet équipement est conforme aux conditions des Directives de la Commission européenne mentionnées ci-dessous:73/23/EEC Directive sur la basse tension y compris la modification 93/68/EEC89/336/EEC Directive CEM y compris les modifications 92/31/EEC et 93/68/EEC 1999/5/EC R&TTE-------------------------------------------------------------------------------------------------------------Informations relatives à l’évacuation des déchets, destinées aux utilisateurs d’appareils électriques et électroniques (appareils ménagers domestiques)Lorsque ce symbole figure sur les produits et/ou les documents qui les accompagnent, cela signifie que les appareils électriques et électroniques ne doivent pas être jetés avec les ordures ménagères.Pour que ces produits subissent un traitement, une récupération et un recyclage appropriés, envoyez-les dans les points de collecte désignés, où ils peuvent être déposés gratuitement.Dans certains pays, il est possible de renvoyer les produits au revendeur local en cas d’achat d’un produit équivalent.En éliminant correctement ce produit, vous contribuerez à la conservation des res-sources vitales et à la prévention des éventuels effets négatifs sur l’environnement et la santé humaine qui pourraient survenir dans le cas contraire.Afin de connaître le point de collecte le plus proche, veuillez contacter vos autorités locales.Des sanctions peuvent être appliquées en cas d’élimination incorrecte de ces déchets, conformément à la législation nationale.Utilisateurs professionnels de l’Union européennePour en savoir plus sur l’élimination des appareils électriques et électroniques, contactez votre revendeur ou fournisseur.Informations sur l’évacuation des déchets dans les pays ne faisant pas par-tie de l’Union européenneCe symbole n’est reconnu que dans l’Union européenne.Pour supprimer ce produit, contactez les autorités locales ou votre revendeur afin de connaître la procédure d’élimination à suivre.
13EContentsIntroduction .....................................................................................14Precautions.....................................................................................15Description of Parts.........................................................................19First-time Operation ........................................................................21LCD (Touchscreen) .........................................................................25Control Panel ..................................................................................27Backing Up/Deleting/Copying Data.................................................31ROM Update ...................................................................................33Buttons............................................................................................34Quick Menu.....................................................................................35Software Keyboard .........................................................................37Signature Capture...........................................................................42Security Measures ..........................................................................43SD Memory Card ............................................................................47Battery Power .................................................................................48Connecting to a Computer/Server ..................................................50Bluetooth.........................................................................................54For Effective Use ............................................................................55LIMITED USE LICENSE AGREEMENT .........................................56Troubleshooting ..............................................................................58Specifications..................................................................................59
14EIntroductionThank you for purchasing this Panasonic wireless display. For optimum perfor-mance and safety, please read these instructions carefully.Terms and illustrations in these instructionszSome illustrations are simplified to help your understanding and may look dif-ferent from the actual unit.zRefer to the catalogs, etc. for the latest information about optional products.CopyrightThis manual is copyrighted by Matsushita Electric Industrial Co., Ltd. with all rights reserved. No part of this manual may be reproduced in any form without the prior written permission of Matsushita Electric Industrial Co., Ltd.No patent liability is assumed with respect to the use of the information contained herein.© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.DisclaimerWireless display specifications and manuals are subject to change without notice. Matsushita Electric Industrial Co., Ltd. assumes no liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the wireless display and the manuals.TrademarksMicrosoft®, Windows® and the Windows logo are registered trademarks of Microsoft Corporation of the United States and/or other countries.SD Logo is a trademark. Citrix® and ICA® protocol are registered trademarks of Citrix Systems, Inc.Bluetooth™ is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Matsushita Electric Industrial Co., Ltd.Panasonic® is a registered trademark of Matsushita Electric Industrial Co., Ltd.Names of products, brands, etc., appearing in this manual are trademarks or regis-tered trademarks of their respective own companies. : Conditions that may result in minor or moderate injury. : Useful and helpful information.Î : Page in these Operating Instructions.CAUTIONNOTE
15EPrecautionsUsageWireless DisplayAvoid Extreme Heat and ColdDo not store or use the wireless display in loca-tions exposed to heat, direct sunlight, or extreme cold.Avoid moving the wire-less display between locations with large tem-perature difference.Operation: 5 °C to 35 °C {41 °F to 95 °F}Storage: -20 °C to 60 °C {-4 °F to 140 °F}Avoid Direct Sunlight on the LCD PanelThe LCD panel should not be exposed to direct sunlight or ultraviolet light.Avoid Humidity, Liquids and DustDo not store or use the wireless display in loca-tions exposed to high humidity, liquids (includ-ing rain) or dust.Prevent ShockAvoid subjecting the wire-less display to severe vibrations or impact. Do not place the wireless display inside a car trunk.Avoid Radio Fre-quency InterferenceDo not place the wireless display near a television or radio receiver.Avoiding Low-tempera-ture BurnsAvoid more than casual contact with any heat producing area of the wireless display, AC adaptor, and any option or accessory you use with it. Even low heat, if warmer than body tem-perature, can cause a burn, if the skin is exposed to the heat source for a long enough period of time.If the LAN port is con-nected to a network such as the ones listed below, a fire or electric shock may result.• Networks other than 100BASE-TX or 10BASE-T.• Phone lines [Tele-phone lines, inter-nal phone lines (on-premise switches), digital public phones, etc.]
16PrecautionsEHandlingzCare should be exercised with regard to the following in order to avoid the possibility of overheating, fire or damage..Keep SD Memory Cards Away From Infants and Small ChildrenAccidental swallowing will result in bodily injury. In the event of accidental swallowing, see a doctor immediately.Avoid Magnetic FieldsKeep the wireless dis-play away from magnets.Data stored on the hard disk may be lost.Avoid StackingDo not place heavy objects on top of the wire-less display.Keep Small Objects AwayDo not insert paper clips or other small objects into the wireless display.Do Not Disassemble the Wireless DisplayDo not attempt to disas-semble your wireless dis-play.Avoid Excessive Force on the DisplayDo not apply excessive downward force on the display, especially when plugs and/or cables are connected to the rear of the wireless display.Battery PackAvoid HeatDo not throw the battery pack into a fire or expose it to excessive heat.Keep Articles AwayDo not place the battery pack together with arti-cles such as necklaces or hairpins when carry-ing or storing.Do Not DisassembleDo not insert sharp objects into the battery pack, expose it to bumps or shocks, deform, disas-semble, or modify it.Do Not ShortDo not short the positive (+) and negative (-) con-tacts.
17EzDo not touch the terminals on the battery pack. The battery pack may no longer function properly if the contacts are dirty or damaged.zDo not expose the battery pack to water, or allow it to become wet.zIf the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining bat-tery level becomes 30% to 40% and store it in a cool, dry place.zThis wireless display prevents over-charging of the battery by recharging only when the remaining power is less than approx. 95% of capacity.zThe battery pack is not charged when the wireless display is first pur-chased. Be sure to charge it before using it for the first time. When the AC adaptor is connected to the wire-less display, charging begins auto-matically.zShould the battery leak and the fluid get into your eyes, do not rub your eyes. Immediately flush your eyes with clear water and see a doctor for medical treatment as soon as possi-ble.Avoid Extreme Heat, Cold and Direct Sun-lightDo not charge, use or leave the battery pack for extended periods where it will be exposed to direct sunlight, in a hot place (in a car on a sunny day, for example), or in a cold place.Do Not Use With Any Other EquipmentThe battery pack is rechargeable and was intended for the speci-fied equipment. Do not use it with any equipment other than the one for which it was designed.Do Not Use This Wire-less Display with a Bat-tery Pack Other Than the One SpecifiedUse only the specified Panasonic battery pack (CF-VZSU44/CF-VZSU44U) with your CF-08. Use of batteries other than those manufactured and sup-plied by Panasonic may represent a safety haz-ard.Do Not Put into a Micro-waveDo not put the battery pack into a microwave oven or a pressurized chamber.Stop UsingShould the battery emit an abnormal odor, become hot to the touch, become discolored, change shape, or become in any way dif-ferent from normal, remove it from the wire-less display and stop using it.
18PrecautionsENOTENOTEzThe battery pack may become warm during recharging or normal use. This is completely normal.zRecharging will not commence if internal temperature of the battery pack is outside of the allowable tem-perature range (0 °C to 45 °C {32°F to 122°F}). Once the allowable range requirement is satisfied, charging begins automatically. Note that the recharging time varies based on the usage conditions. (Recharging takes longer than usual when the tempera-ture is 10 °C {50°F} or below.)zIf the temperature is low, the operat-ing time is shortened. Only use the equipment within the allowable tem-perature range.zThe battery pack is a consumable item. If the amount of time the equip-ment can be run by using a particular battery pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery pack should be replaced with a new one.zWhen transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected.zAlways power off the equipment when it is not in use. Leaving the equipment on when the AC adaptor is not connected will exhaust the remaining battery capacity.
19EDescription of PartsA. LCD (Touchscreen)B. Wireless LAN antennaC. Bluetooth antennaD. Power statusE. Power buttonF. Battery statusG. DC-IN jackH. LAN portI. Cursor keyJ. Keyboard buttonK. USB portL. USER buttonM. SD Card slotN. SD memory card statusCAUTIONzDuring a thunderstorm, disconnect the AC plug.
20Description of PartsE<Models for U.S.A/Canada>A lithium ion battery that is recyclable powers the product you have pur-chased.Please call 1-800-8-BATTERY for infor-mation on how to recycle this battery.L’appareil que vous vous êtes procuré est alimenté par une bat-terie au lithium-ion.Pour des renseigne-ments sur le recy-clage de la batterie, veuillez composer le 1-800-8-BATTERY.A. Battery cover latchB. Hand strapAdjust the length of the belt so that the wireless display does not fall by mistake, and firmly hold the wireless display when using it.C. Battery packD. Microphone jackYou can use a stereo condenser microphone. Connecting another type of microphone may interrupt audio input or may cause a mal-function.E. Headphone jackYou can connect headphones or amplified speakers. When they are connected, audio from the internal speakers is not heard.F. Stylus pen holderG. Security lockH. SpeakerI. Expansion bus connectorCAUTIONzDo not put metallic objects or magnetic media close to the speakers.zDo not touch the expansion bus connector. The wireless display may no longer function properly if the connector is dirty or damaged.
21EFirst-time OperationPreparationACheck and identify the supplied accessories.If you do not find the described accessories, contact Panasonic Technical Support.BRead the LIMITED USE LICENSE AGREEMENT before breaking the seal on the wireless display’s packaging (Îpage 56).1 Insert the battery pack.• AC adaptor..................... 1Model No.: CF-AA1623AM• AC Cord .......................1• Battery Pack..............1Model No.: CF-VZSU44U• Stylus.............................. 1• Operating Instructions (This book)....................1
22First-time OperationEATurn the wireless display over, and open the hand strap cover.BRemove the hand strap.CSlide the battery latch.DOpen the battery cover.EFirmly attach the battery pack to the connector.FClose the battery cover.GSlide the battery latch.HAttach the hand strap.IAttach the hand strap cover.To remove the battery packASlide the battery latch as in step C.BOpen the battery cover as in step D.CPull the tab of the battery pack and remove it from the wireless display.CAUTIONzBe careful not to catch the tab when you close the battery cover.zMake sure the cover is securely attached. Otherwise the battery pack may fall when you carry the wireless display.zDo not touch the terminals of the battery pack and the wireless display. Doing so can make the terminals dirty or damaged, and may cause malfunction of the battery pack and the wireless display.zUse only the specified battery pack (CF-VZSU44) with your wireless display.
23E2 Connect your wireless display to a power outlet.The battery charging starts automatically.CAUTIONzWhen using the wireless display for the first time, do not connect any peripheral device except the battery pack and AC adaptor.zHandling the AC adaptor• Do not twist or pull the AC power cord forcefully. Doing so may damage the connections.• Use only the specified AC adaptor with your wireless display. Using an AC adaptor other than the one supplied might damage the battery and/or the wireless display.• When the DC plug is not connected to the wireless display, disconnect the AC cord from your AC wall outlet.• Problems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect your wireless display, an unin-terruptible power source (UPS) is highly recommended unless running from the battery pack alone.3 Turn on the wireless display.Press and hold the power button for approxi-mately 1 - 2 seconds until the power indicator lights.To turn off the wireless displayPress and hold the power button for approximately 1 - 2 seconds until the power indicator disappears.The message “Preparing to Power off…” will be displayed.
24First-time OperationE4 Calibrate the touchscreen.Touch the “+” mark on the calibration screen with the stylus (included) for about one second.After the calibration procedure is executed (e.g., after the twelve “+” marks are touched), the pro-cedure ends when the center of the cursor key (A) is pressed.5 Make the date and time setting.The [Date/Time Properties] screen will appear automatically.Set the current time and time zone, and then tap .zYou can use the software keyboard when you set the time. For information about how to use the Software Keyboard: Îpage 37If the [Date/Time Properties] screen does not appear automaticallyDouble-tap on the desktop, and double-tap [Date/Time].The [Date/Time Properties] screen will appear.CAUTIONzTo take effect this setting when you start the wireless display next time, you have to perform Flash Backup to save this setting. (Îpage 31)
25ELCD (Touchscreen)Using the StylusUse the stylus provided to perform operations on the touchscreen. The stylus is located in the stylus holder (A), and can be held like a pen or pencil. The following operations are possible on the touchscreen.TappingYou can select an item on the screen by tapping it with the stylus. This operation is called a “tap”. DraggingYou can drag on item on the screen by holding the sty-lus down over the item and then moving the stylus. This operation is called a “drag”.Tapping and HoldingYou can tap and hold the stylus on an item to see a list of actions available for that item. On the pop-up menu that appears, tap the action you want to perform.Handling the StyluszClean the stylus tip and screen prior to operation. Foreign particles can scratch the screen and impede the operation of the stylus.zUse the provided stylus only on the screen. Using it for any other purpose may damage the stylus and scratch the screen.
26LCD (Touchscreen)EHandling the TouchscreenzUse the provided stylus with CF-08. Do not use an implement other than the stylus that comes with the wireless display.zDo not place any object on the surface or press down forcefully with sharp-pointed objects (e.g., nails), or hard objects that can leave marks (e.g., pencils and ball point pens).zDo not operate the wireless display when such things as dust are on the LCD. Do not allow substances such as oil to contact the LCD. The cursor may not work properly in such cases.Aligning the touchscreenAlign the touchscreen if the cursor does not correctly move to the position where the stylus touches the touchscreen of the wireless display.ADouble-tap on the desktop, and double-tap [Stylus].BTap [Calibration] tab, and tap [Recalibrate].
27EControl PanelIf you double-tap on the desktop, you can see much of the list of functions that can be used on this wireless display. If you double-tap the icon (or the name), the screen will start up. Here, we will introduce the name of the function and provide a brief explanation of each. CAUTIONzAfter changing settings, if you do not tap , some settings after the changes will take effect.Accessibility Allows you to change settings to make the keyboard, sound, screen, mouse, and other devices easier to use.Backlight Allows you to change the brightness of the screen’s backlight. Move the slider to the left to make the backlight darker, and to the right to make it brighter. Bluetooth Device PropertiesControls Bluetooth connections. (Îpage 54)Buttons Assigns applications to be launched when the keyboard button and USER button are pressed. (Îpage 34)Certificates Allows you to see a list of certificates installed in the wireless display.CF-08 Manage-mentControls the start/termination of the CF-08 device management function.Date/Time Sets the current date, time, and time zone.
28Control PanelEDevice Manage-mentSets the connection to the device man-agement server.Dialing Sets dialing properties.Display Sets the wallpaper and window color schemes.Error Reporting Reports software errors to Microsoft.Flash Backup Îpage 31Flash Copy Îpage 31Flash Delete Îpage 31Input Panel Sets Input Panel properties for the soft-ware keyboard, etc.Internet Options Sets Internet Explorer properties.Keyboard Sets the key repeat intervals when a USB keyboard is connected. Mouse Sets the double click interval when an external mouse is connected.
29ENetwork and Dial-up ConnectionsSets properties for installed network adaptors (LAN, wireless LAN). Network Informa-tionConfirms network status when the wire-less display is connected to a server. Power Displays remaining power in the main battery, and sets power conservation properties.Printers Sets properties for the local printer con-nected to the wireless display.Quick Menu Sets the applications allocated to Quick Menu. (Îpage 35)Remove Programs Allows you to uninstall programs that were installed earlier. ROM Update Îpage 33Rotate Allows you to rotate the screen. Using [0 degrees (landscape)] as the standard, you can rotate the screen [90 degrees], [180 degrees] or [270 degrees] either clockwise or counterclockwise. To take effect the screen rotation, tap [Rotate].Security (Supervi-sor/User)Îpage 43Stylus Sets the intervals for double taps and cal-ibrates the stylus pad.
30Control PanelESystem Sets device names and displays the Win-dows CE version, memory usage vol-ume, copyrights for internal software, and information unique to this wireless dis-play.Terminal Service Client LicensesDisplays Terminal Service Client Licenses that have been acquired.Volume & Sounds Adjusts volume, sets system sounds, and adjusts microphone gain.Wireless LAN Controls Wireless LAN connections.
31EBacking up / Deleting / Copying DataTo back up data from CF-08 RAM to Flash ROM, perform Flash Backup by follow-ing the instructions below.ADouble-tap on the desktop and double-tap [Flash Backup].BConnect your wireless display to a power outlet. (Îpage 23)CTap [Start Backup].Backing up data will start.DWhen the message “Backup successful.” appears, tap .To delete backup data, perform Flash Delete by following the instructions below.ADouble-tap on the desktop and double-tap [Flash Delete].BConnect your wireless display to a power outlet. (Îpage 23)CTap [Delete Backup].When the confirmation message appears, tap [Yes].Deleting data will start.DWhen the message “Backup data has been deleted.” appears, tap .CAUTIONzWhen you turn on the wireless display for the first time after deleting data, cali-brate the touchscreen (Îpage 24).To copy data from CF-08 RAM to the media (SD Memory Card, etc.), perform Flash Copy by following the instructions below.ADouble-tap on the desktop and double-tap [Flash Copy].BConnect your wireless display to a power outlet. (Îpage 23)CInsert the copy destination media, and select the media in “Copy To.”Backing up dataDeleting dataCopying data
32Backing up / Deleting / Copying DataEDEnter the file name and tap [Copy Backup].Copying data will start.zThe file that has already existed cannot be overwritten. In this case, tap , change the file name, and tap [Copy Backup]. EWhen the message “Copy successful.” appears, tap .How to update data: Îpage 33To return the wireless display to the default conditionPerform the following procedure.zWhen turning on the wireless display, turn it off.AConnect your wireless display to a power outlet. (Îpage 23)BTurn on the wireless display. (Îpage 23)CPress and hold the keyboard button and USER button (Îpage 34) until the message “Reset to device to factory default...” appears.DSelect [Yes].
33EROM UpdateTo update the copied data, perform “ROM Update” by following the instructions below.ADouble-tap on the desktop and then double-tap [ROM Update].BConnect your wireless display to a power outlet. (Îpage 23)CInsert the media with “.pkg” file copied, and then tap [Brouse].DSelect the file and tap .ETap [Next].FTap [Update Start].GWhen the confirmation message appears, tap [Yes].ROM Update will start.When ROM Update terminates, the wireless display will restart and the [Date/Time Properties] screen will appear automatically. (Îpage 24)
34EButtonsYou can display screens for frequently used functions and applications by pressing specified keyboard button or USER button on this wireless display.Two functions can be assigned to each button; one that starts up with a short push (less than 2 seconds) and one that starts up with a long push (more than 2 seconds).At the time of purchase, this wireless display is set so that the screens for the fol-lowing functions are displayed.Settings can be changed using the following procedure.ADouble-tap on the desktop and then double-tap [Buttons].BWhen the [Buttons] screen appears, tap and select the function name in accordance with the button positions and short/long push that you want to set.CTap .*1 To execute the right click operation:ATap [Buttons] in [Control Panel], and set [Right Click] according to the position and push length (long/short) for the button that you want to use. BPress the button that you set in A. You can use the right click once. Each time after this, before using the right click once, execute operation B above. You can also execute the right click operation using Quick Menu (Îpage 35). Button short push long pushKeyboard button Input Panel Input Panel SelectorUSER button Quick Menu (Îpage 35)Right Click*1
35EQuick MenuQuick Menu is used to display information about the wireless display, or to enable frequently used applications and functions to be launched quickly without going through Control Panel. At the time of purchase, Quick Menu can be launched with a short push of the USER button .How to change Quick Menu launching method: Îpage 34A.Display remaining battery level ([Power] in Control Panel Îpage 29)B.Display status of wireless LANC.Set and change sound volumes ([Volume & Sounds] in Control Panel Îpage 30)D.Set and change display backlight brightness ([Backlight] in Control Panel Îpage 27)E.Start up frequently used applica-tions and functionsAt the time of purchase, [Right Click]*1, [Input Panel Selector], [Control Panel] and [Stylus Calibla-tion] are set in Quick Menu. You can change these settings using the following procedure. ADouble-tap on the desktop and double-tap [Quick Menu]. The [QuickMenu Application Assignment] screen will appear.BTap the button for the application/function you want to change, and then tap the application/function you want to assign to that button location. CTap .
36Quick MenuE*1 To execute the right click operation:ASet [Right Click] in the [QuickMenu Application Assignment] screen.BLaunch Quick Menu and tap [Right Click].You can use the right click once. Each time after this, before using the right click once, execute operation B above. You can also execute the right click operation by pressing the keyboard button or USER button. (Îpage 34)
37ESoftware KeyboardTo show or hide the Software KeyboardzPress and hold the keyboard button or USER button . (Îpage 34)There are five input methods. “Numeric keyboard” and “Full keyboard” can be selected as either large or small panels.To change the input method, use any of the following methods.zPress and hold the keyboard button or USER button (Îpage 34) or tap [Input Panel Selector] in the [Quick Menu] screen (Îpage 35), and select the input method that you want to use on the [Input Panel Selector] screen.zDouble-tap [Input Panel] in [Control Panel], select [Key-board] or [Transcriber] in “Current Input Method” and tap .• If you select [Keyboard], tap [Options] to change the input method or panel size. • To use Transcriber Îpage 39
38Software KeyboardE
39ETranscriberTranscriber is a function that enables you to input letters, characters or symbols by writing directly on the touchscreen using the stylus.To display the [Transcriber: Options] screen, tap .Tap on the various tabs to set the following functions.[Quick Settings] TabRecognition: Change the language of therecognition engine. Writing Direction: Change the handwritinginput direction. Intro screen: If the check mark is added, the Help screen will be displayed when theTranscriber starts up. Sound: If the check mark is added, you will hear a sound when the Transcriber starts up. The volume of this sound will be the same as the volume set in Quick Menu (Îpage 35) or in [Volume & Sounds] (Îpage 30). A. Option settingsDisplays the [Transcriber: Options] screen of Transcriber option set-tings. (Î below) B. Change recognition modeRunning hand/block letter (charac-ter (Alphabet/symbol/numeric)).C. Display symbol input panelDisplays the screen for symbol input.D. Change Upper/Lower/symbol modeChanges input mode to Upper/Lower/symbol mode.E. SpaceInputs space.F. Re turnInputs return code.G. Left moveMoves cursor to left.H. Right moveMoves cursor to right.I. BSBackspace (delete one character)J. HelpDisplays help screen.
40Software KeyboardE[Inking] TabRecognition Delay: Slide the bar to set the timefor recognition of handwritten characters. Add space after: If the check mark is added,when handwritten characters are recognized and displayed on the screen, a single space will also be displayed at the end of eachcharacter. Pen: Tap to set the width and color of the ink.[Advanced] TabShorthand: Register shorthandThe following functions can be assignedfor handwriting input. zText expansionAllows you to display words, phrases, orsentences by inputting handwrittenabbreviations. e.g.: Input “xyz” in handwriting J Displays “I am a student.” zFunctionAllows you to display dates, names, or other information by inputting handwrit-ten abbreviations.e.g.: Input “ABC” in handwriting J Displays company name.zRun programAllows you to start up a program by inputting handwritten characters. e.g.: Input “abc” in handwriting J Starts up [Control Panel]. Functions can be registered using the following procedure. 1Tap [Settings] to the right of “Shorthand.” 2 Tap [Add]. After you tap [Finish] in step 4, the screen will return to step 2. To register two or more functions in succession, repeat step 2 and 3. 3 Select the function that you want to register ([Text expan-sion], [Function] or [Run program]) and tap [Next]. 4 To register shorthand in [Text expansion]:
41EAInput “xyz” in handwriting on the screen. “xyz" will be displayed in the “Shorthand” box. BTap the “Text expansion” box once, and then input “I am a student” in handwriting on the screen. “I am a student” will be displayed in the “Text expansion” box. CTap [Finish]. The screen will automatically return to step 2. To register shorthand in [Function]: AInput “ABC” in handwriting on the screen.“ABC” will be displayed in the “Shorthand” box.BTap in the “Function” box, and a list of information will appear; select one of these, and tap [Finish]. The screen will automatically return to step 2.To register shorthand in [Run program]: AInput “abc” in handwriting on the screen.“abc” will be displayed in the “Shorthand” box.BTap in the “Run program” box, and a list of bootable programs will appear; select one of these, and tap [Finish]. The screen will automatically return to step 2.5Tap .Dictionaries: Select a dictionary.
42ESignature CaptureSignature Capture operates on CF-08, supporting input of signatures in applica-tions running on the connection destination server.How to launch Signature capture:ADouble-tap , and double-tap [Windows].BDouble-tap [Programs], and tap [Signature Capture].You can set the wireless display to launch Signature Capture using the Quick Menu (Îpage 35), keyboard button or USER button (Îpage 34). You can set the thickness of the writing or the size of the bitmap data to be saved by tapping and then tapping [Setting]. Tap [Capture] to temporarily save the handwritten image on the server computer clipboard.To view the handwritten image while connected to the server: ATap [start] - [Run].BInput [Clipbrd.exe] and tap [OK].The [CLIP BOOK] screen will appear.
43ESecurity MeasuresYou can set the password and/or enable/disable some functions for security pur-pose.You can set two types of users with different operating authorities. Supervisor: Changes settings related to the wireless display operations, and con-trols the operations of regular users. Set the Supervisor Password in advance using the [Supervisor] tab in Security Settings (Supervisor) (Î below). User: Executes only operations that have been limited by the Supervisor. ADouble-tap on the desktop.BDouble-tap [Security (Supervisor)]. CTap the [Supervisor], [User] or [Device Permission] tab.zFor information on the tab:[Supervisor] tab Îpage 44[User] tab Îpage 44[Device Permission] tab Îpage 45<When you tap [Supervisor] or [User] tab>DEnter your password in [New Password].zWhen the password has been set, you need to enter your password in [Current Password].zTo disable the password, leave the input field empty.EEnter your password again in [Confirm Password] and tap .FAt the confirmation message, tap [Yes].When the message that recommends executing Flash Backup appears, tap .CAUTIONzDo not forget your password. If you forget your Supervisor Password, you will not be able to use your wireless display. Contact Panasonic Technical Support.zSoon after you create or change the setting, perform Flash Backup (Îpage 31). If you do not do so, the setting will not be reflected next time when you turn on the power for the wireless display.NOTENOTEzThe password will not be displayed on the screen.zYou can use up to 40 alphanumeric characters (excluding spaces).zDisabling the Supervisor Password also disables the User Password.
44Security MeasuresESecurity Settings (Supervisor)The Supervisor can make security settings using the following procedure after log-ging on with the Supervisor Password, or when no password has been set.zWhen you log on as a Supervisor, press and hold the power button with the USER button pressed, and enter the password when the [Enter Password] screen appears. If you do not do so, even when you enter the Supervisor Pass-word, the wireless display will run in the User operating environment.[Supervisor] tab[User] tab(Set when Supervisor and User log on separately. Supervisor can make settings for Users after the Supervisor password is set in the [Supervisor] tab.) Item After the check mark is addedAuto Launch When you select an application, that application will automatically start up when the wireless display is started. For example, if the connection settings for Remote Desktop Connection or ICA Client have been made in advance (Îpage 50), you can set these applications to start up automatically. Wait Network Connec-tionAn application set in [Auto Launch] will launch after the network connection is built up.Item After the check mark is addedSkip Password Dialog Allows Users to log on without entering a password. The password input screen is not displayed. (If you press and hold the power button with the USER button pressed, the [Enter Password] screen will be displayed, and the User can log on with the User Password.)Allow Connection Con-figurationAllows creation and changes of connection settings after logging on. Double-tap or on the desktop to display the connection setting screen.
45E[Device Permission] tab(Same settings for Supervisor and User.) Allow Application AssignmentAllocates applications to the keyboard button or USER button (Îpage 34) or Quick Menu (Îpage 35).File Explorer Enables viewing of files via Windows Explorer after logging on.Double-tap on the desktop. Internet Explorer Allows access to the Web browser, and enables cre-ation of/changes to connection settings after logging on. Double-tap on the desktop. Control Panel When the User is using the wireless display, items displayed in the Control Panel can be selected using the following procedure. ATap [Permission] to display the [Permission] screen. BAdd the check mark for only the items to be displayed in the [Control Panel] screen, and tap .Allow Change Auto LaunchAllows users to change Auto Launch setting.Allow Launch Îpage 44Wait Network Connec-tionÎpage 44ExplanationOf the following devices, only those with a check mark can be used. •Ethernet • Wireless LAN • Bluetooth • SD Memory • USB Memory
46Security MeasuresESecurity Settings (User)Users can make security settings in the following cases. zAfter logging on with a User Password. zWhen you add the check mark for [Skip Password Dialog].zWhen the User Password has not been set, and the User has logged on with-out entering a password. How to start up the [Security Setting] screen:ADouble-tap on the desktop.BDouble-tap [Security (User)]. The following screen will be displayed.[User] tabzIf a User Password has not been set in the [User] tab of Security Settings (Supervisor) (Îpage 44), a password cannot be changed, deleted or newly created here. Item After the check mark is addedAuto Launch Îpage 44Wait Network Connec-tionÎpage 44
47ESD Memory CardAbout SD Memory CardAn SD Memory Card can be used for the following purposes.zThe exchange of data with various devices equipped with an SD Memory Card slot, audio storage, and so on.zUse as a memory card (e.g., use as a storage unit on which files can be written).Inserting/Removing a Card1 Open the SD Memory Card slot cover.2 Insert/Remove a Card.To insert the cardInsert the SD Memory Card with the label side facing up and with the cut corner in front.To remove the cardAPress the card so it comes out of the slot.BDraw it straight out.3 Close the SD card slot cover.To insert the card To remove the card
48EBattery PowerNOTENOTEzOnce the battery is fully charged, the wireless display performs recharging only when the battery level becomes less than approximately 95%, so overcharging is avoided.You can check the remaining battery charge using any of the following methods.zDouble-tap on the desktop, double-tap [Power] and tap [Battery] tab.zPress and hold the keyboard button or USER button (Îpage 34) and run Quick Menu (Îpage 35).Battery IndicatorBattery indicator Battery statusNot lit The battery pack is not inserted or not being charged. Pulsing orange Charging is in progress. Green The battery is fully-charged.Red The remaining battery is approximately 9% or less.Blinking red The battery pack or the charging circuit is not operating normally.Blinking orange The battery cannot be charged temporarily due to the fol-lowing reasons: zIts internal temperature is out of the acceptable range. zThe power supply is not enough because software applications or peripheral devices are consuming a large amount of power.Checking the Remaining Battery Charge
49EYou can reduce power consumption using the following method.When using the battery, the wireless display can be used for a longer period of time.Power conservation effects can be achieved even when the AC adaptor is connected.zDouble-tap on the desktop, dou-ble-tap [Power] and tap [Schemes] tab.Power consumption can also be mini-mized with detailed settings; for exam-ple, by reducing the time setting for [Turn off LCD].The battery pack is a consumable item so the replacement (CF-VZSU44) will be necessary. If the battery operation time becomes noticeably short, replace with a new battery.How to remove/insert the battery pack:Îpage 21Replacing the Battery Pack
50EConnecting to a Computer / ServerEither a LAN or wireless LAN can be used for connection.Before making connection settings, perform the following procedure.zAfter completing the computer/server settings (IP address, subnet mask, etc.), perform wireless display settings.ADouble-tap on the desktop, and then double-tap [Network and Dial-up Connections].B<When making connection with a LAN>Double-tap [ETHERNET1].<When making connection with a wireless LAN>Double-tap [WIRELESS LAN1].CTap the [IP Address] tab, select [Specify an IP address], and enter the IP Address, Subnet Mask, and Default Gateway to match with the computer/server connected.DTap .1-1 ConnectionsWhen connecting to Microsoft® Windows® XP ProfessionalFollow the instructions below to connect using Remote Desktop Connection.zAfter completing the computer settings (IP address, subnet mask, etc.), per-form wireless display settings.1 Connect the necessary devices, and turn the power on for the computer. 2 Turn on the power for the wireless display.(Perform step A-C only when making connections with a wireless LAN.)ADouble-tap on the desktop, and then tap [Wireless LAN]. BTap the [Wireless Information] tab, and then tap the access point from the list.Now, select settings as follows according to your own network environment.CTap [Connect].
51E3 Double-tap on the desktop.4 Tap [Options]. Enter the Computer (IP address or computer/server name for the connec-tion destination), User name (account name for the computer/server to be connected), and Password (the password required to log on to the com-puter/server to be connected).zTap [Save As], enter the file name, select the save destination, and tap . An “rdp.” file will be created, and the data entered in the above pro-cedure will be saved. In this way, the next time you want to use the Remote Desktop (and any time after that), you can display the server desktop screen by double-tapping the “rdp.” file.5 Tap [Connect].The server desktop screen will be displayed.Connecting multiple clientsWhen connecting to a Microsoft® Windows® 2000 Server / Microsoft® Windows® 2003 ServerFor information on how to connect using Remote Desktop Connection, refer to step 1-5 of “1-1 Connections” (Îpage 50).When connecting to a server computer running Citrix® MetaFrame® Pre-sentation ServerFollow the instructions below to connect using Citrix® ICA® Client.zFor information on Citrix® server, refer to the manual of the server.1 Turn on the power for the wireless display.2 Double-tap on the desktop, and tap [Accept].3 Connect the necessary devices, and turn the power on for the server.(Perform step A-C only when making connections with a wireless LAN.)
52Connecting to a Computer / ServerEADouble-tap on the desktop, and then double-tap [Wireless LAN]. BTap the [Wireless Information] tab, and then tap the access point from the list.Now, select settings as follows according to your own network environment.CTap [Connect].4 Double-tap on the desktop, and tap [Create New Connection].5 Enter the IP address or server name for the connection destination in “Server or Published Application”, and tap [Save]. The name entered above will be displayed in the Main screen of the ICA Cli-ent.6 Select the name entered in step 5, and tap [Edit]. 7 Tap [Edit Logon Information], enter Username and Pass-word (and Domain, if required), and tap [Save]. 8 Tap [Main] at the top of the screen. 9 Select the name entered in step 5 and tap [Edit].10 Tap [Edit Title], add the check mark for [Create a Desktop shortcut], and tap [Save], then tap .*1 will appear on the desktop. 11 Double-tap *1 the desktop. The server desktop screen will be displayed.*1 The name entered in step 5 will be displayed.Perform the following operations.zTap [start] - [Log Off] - [log Off].Terminating the connection
53Ez<Only when using Remote Desktop Connection>Tap , then tap .If you tap [start] - [Shut Down], the power for the server itself will be turned off.
54EBluetoothTo launch the [Bluetooth] screenADouble-tap on the desktop.BDouble-tap [Bluetooth Device Properties].To turn the power on/off BluetoothTap [General] tab, and add the check mark for [Enable Bluetooth].A. Set the device name for BluetoothB. Set the passkey used when connecting to the opposing Bluetooth device. C. Set the Bluetooth power status when the CF-08 starts up.D. Set whether the opposing Bluetooth device is able to detect the CF-08 when the Bluetooth device is detected.To set operations in Serial Port ProfileTap [Serial Port] tab.To set operations in DialUp Network ProfileTap [DialUp Network] tab.To show information about BluetoothTap [About] tab.
55EFor Effective UseMaintenanceLCDDo not use water when cleaning the panel. Ingredients included in water may leave residue and reduce readability of the screen.<When cleaning dust/dirt>Avoid rubbing off dust/dirt with cloth since it may leave scratch on the screen.Sweep dust/dirt with fine brush, then wipe it with "dry" soft cloth used for cleaning glasses.<When cleaning oily surface>Apply camera lens cleaner on a soft gauze and clean it with gentle force. Then, wipe with dry soft cloth used for cleaning glasses.Areas excluding the LCDWipe these areas with a soft cloth, after applying water or detergent diluted with water to the soft cloth and firmly wringing out excess water.CAUTIONzDo not use benzene, thinner, or rubbing alcohol. Doing so may adversely affect the surface, e.g., discoloration. In addition, do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to the surface.zDo not directly add or spray water or detergent. If liquid enters the inside of the computer, it may cause the computer to work improperly or be damaged.
56ELIMITED USE LICENSE AGREEMENTTHE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC® PRODUCT (“PRODUCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.Matsushita Electric Industrial Co., Ltd. (“MEI”) has developed or otherwise obtained the Programs and hereby licenses their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intended results, and for the installation, use and results obtained therefrom.LICENSEA. MEI hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only a LIM-ITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership and rights shall remain with MEI or its suppliers.B. You may use the Programs only on the single Product which was accompanied by the Programs.C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not distribute or otherwise make the Programs or related documentation available to any third party, by time-sharing or otherwise, without the prior written consent of MEI.D. You may not copy or reproduce, or permit to be copied or reproduced, the Pro-grams or related documentation for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your use of the Programs on the single Product which was accompanied by the Pro-grams. You shall not modify, or attempt to modify, the Programs.E. You may transfer the Programs and license them to another party only in con-nection with your transfer of the single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also transfer all copies, whether in printed or machine readable form, of every Pro-gram, and the related documentation, to the same party or destroy any such copies not so transferred.
57EF. You may not remove any copyright, trademark or other notice or product identi-fication from the Programs and you must reproduce and include any such notice or product identification on any copy of any Program.YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANI-CALLY OR ELECTRONICALLY TRACE THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PRO-GRAMS OR ANY COPY THEREOF, IN WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PERMITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.TERMThis license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate this license at any time by destroying, at your expense, the Programs and related documentation together with all copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any such ter-mination, you agree to destroy, at your expense, the Programs and related docu-mentation together with all copies thereof in any form.YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDER-STAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PRO-POSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MATTER OF THIS AGREEMENT.About Intel® software productsThe enclosed software products and documentation were developed at private expense, and are provided with “RESTRICTED RIGHTS.” Use, duplication or disclosure by the government is subject to restrictions as set forth in FAR 52.227-14 and DFARS 252.227-7013 et. seq. or its successor. The use of this product by the government constitutes acknowledgment of Intel’s proprietary rights in the product.
58ETroubleshootingFollow the instructions below when a problem has occurred. For a software prob-lem, refer to the software’s instruction manual. If the problem persists, contact Panasonic Technical Support.No display after powering onzHas the computer or wireless display been set to the power-saving mode? To resume operation of your computer from the condition where the power of the display is off (for energy conser-vation purposes), touch the screen.An afterimage appears (i.e., green, red, and blue dots remain on the display) or there are dots not displaying the correct colorszHigh-precision and advanced technologies are neces-sary in the production of color liquid crystal displays (color LCDs). Therefore, if 0.002% or less of the picture elements either fail to light or remain constantly lit (that is, more than 99.998% of elements are functioning prop-erly), no defect is considered to exist.
60SpecificationsE*1 <Only for North America>The AC adaptor is compatible with power sources up to 240 V AC adaptor. The wireless display is supplied with a 125 V AC compatible AC cord.*2 Varies depending on the usage conditions.*3 Approx. 0.9 W when the battery pack is fully charged (or not being charged) and the wireless display is OFF.*4 Rated power consumption
© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.Printed in Japan FJ0306-0DFQX5591ZA

Navigation menu