Panasonic of North America 9TGCF-F91 Toughbook PC with WWAN, WLAN and Bluetooth User Manual Operating Instructions

Download:
Mirror Download [FCC.gov]
Document ID	1287585
Application ID	VaxVlU7PIgFs+jKBwCsbHw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	236.97kB (2962167 bits)
Date Submitted	2010-05-27 00:00:00
Date Available	2010-07-11 00:00:00
Creation Date	2017-11-09 09:43:13
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-09 09:43:13
Document Title	Operating Instructions
Document Creator	FrameMaker 7.1
Document Author:	Panasonic

OPERATING INSTRUCTIONS
Personal Computer
Model No.
CF-F9 series
Contents
On-screen Manual .......................................17
Handling and Maintenance .............................18
Reinstalling Software ....................................22
Troubleshooting
Troubleshooting (Basic)
................................24
Useful Information
Useful Information
Troubleshooting
Introduction .................................................2
Read Me First ..............................................3
(Precautions)
Description of Parts .....................................11
First-time Operation .....................................13
Getting Started
Getting Started
For further information about the computer, you can refer to the on-screen
manual.
To access the on-screen manual
Î page 17 “On-screen Manual”
LIMITED USE LICENSE AGREEMENT ..............28
Specifications ............................................30
LIMITED WARRANTY ..................................33
For your technical support office, refer to
“LIMITED WARRANTY.”
Please read these instructions carefully before using this product, and save this manual for future use.
Appendix
Appendix
Introduction
Thank you for purchasing the Panasonic product. For optimum performance and safety, please read these instructions
carefully.
„ Terms and illustrations in these instructions
CAUTION
NOTE
Enter :
Fn + F5 :
Conditions that may result in minor or moderate injury.
Useful and helpful information.
Press [Enter] key.
Press and hold [Fn] key, and then press [F5] key.
(Start) - [All Programs]: Click
(Start), and then click [All Programs].
Getting Started
[start] - [Run] : Click [start], and then click [Run].
Î:
Page in these Operating Instructions.
Î
Reference to the on-screen manuals.
Useful Information
Some illustrations are simplified to help your understanding and may look different from the actual unit.
If you do not log on as an administrator, you cannot use some functions or cannot display some screens.
Refer for the latest information about optional products to the catalogs, etc.
In these instructions, the names and terms are referred as follows.
• “Genuine Windows® 7 Professional” as “Windows” or “Windows 7”
• “Genuine Microsoft® Windows® XP Professional Service Pack 3” as “Windows” or “Windows XP”
• “WinDVD™ 8 (OEM Version)” as “WinDVD”
z The display modes are referred as follows. ( ) indicates the terms in [Intel® Graphics and Media Control Panel]
screen. To display the screen, right-click the desktop and click [Graphics Properties].
• Internal LCD (Notebook): The computer’s display
• External display (Monitor): External display
• Simultaneous display (Intel (R) Dual Display Clone): The same screen is displayed on the internal LCD and the
external display.
• Extended Desktop: The extended working area across the internal LCD and the external display.
Troubleshooting
„ Disclaimer
Computer specifications and manuals are subject to change without notice. Panasonic Corporation assumes no liability
for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.
„ Trademarks
Microsoft®, Windows® and the Windows logo are registered trademarks of Microsoft Corporation of the United States
and/or other countries.
Intel, Core and PROSet are either registered trademarks or trademarks of Intel Corporation.
SDHC Logo is a trademark of 3D-3C, LLC.
Appendix
Adobe, the Adobe logo and Adobe Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
Bluetooth™ is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Panasonic Corporation.
Corel, InterVideo, WinDVD™, the InterVideo logo and the Corel logo are trademarks or registered trademarks of Corel
Corporation and/or its subsidiaries in Canada, the United States and/or other countries.
Sonic and Roxio are trademarks or registered trademarks of Sonic in the United States and/or other countries.
Computrace® is a registered trademark of Absolute® Software Corp.
Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective
own companies.
Read Me First
Models for U.S.A.
FCC RF Exposure Warning:
z This equipment is provided with PC Card slot that could
be used with wireless transmitters, which will be specifically recommended when they become available.
Other third-party wireless transmitters have not been
RF exposure evaluated for use with this computer and
may not comply with FCC RF exposure requirements.

z This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment.
z This equipment has been approved for portable operation, and does not require any minimum spacing be
provided between antennas and all person’s body.
z This equipment may not be co-located or operated
with any other antenna or transmitter.
3.
4.
5.
25-M-3

z This PC with WWAN transmitter installed, has been
approved for mobile operation and to assure compliance with RF exposure requirements, a minimum of 20
cm (8 inches) must be maintained between the WWAN
antenna located in top of LCD and all person’s body
(excluding extremities of hands, wrist and feet) during
wireless modes of operation.
6.
Useful Information
Troubleshooting
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
2.
information, the FCC registration number and ringer
equivalence number (REN) for this equipment. If
required, this information must be provided to the telephone company.
An FCC compliant telephone cord and modular plug is
provided with this equipment. This equipment is
designed to be connected to the telephone network or
premises wiring using a compatible modular jack
which is Part 68 compliant. See Installation Instructions for details.
The REN is used to determine the quantity of devices
which may be connected to the telephone line. Excessive RENs on the telephone line may result in the
devices not ringing in response to an incoming call. In
most, but not all area, the sum of RENs should not
exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined
by the total RENs, contact the local telephone company.
If your telephone equipment cause harm to the telephone network, the telephone company will notify you
in advice that temporary discontinuance of service
may be required. But if advice notice isn’t practical, the
telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The telephone company may take changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens
the telephone company will provide advance notice in
order for you to make necessary modifications to
maintain uninterrupted service.
If trouble is experienced with this equipment, for repair
or warranty information, please contact Panasonic
Corporation of North America at DIAL TOLL FREE 1800-LAPTOP5 (1-800-527-8675). If the equipment is
causing harm to the telephone network, the telephone
company may request that you disconnect the equipment until the problem is resolved.
Appendix
Warning
To assure continued compliance, use only shielded interface cables when connecting to a computer or peripheral.
Also, any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
Getting Started


Federal Communications Commission Radio Frez This product is restricted to indoor use due to its operquency Interference Statement
ation in the 5.15 to 5.25 GHz frequency range.
Note: This equipment has been tested and found to comFCC requires this product to be used indoors for the
ply with the limits for a Class B digital device, pursuant to
frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile SatelPart 15 of the FCC Rules. These limits are designed to
lite systems. High power radars are allocated as
provide reasonable protection against harmful interferprimary users of the 5.25 to 5.35 GHz and 5.65 to 5.85
ence in a residential installation. This equipment generGHz bands. These radar stations can cause interferates, uses and can radiate radio frequency energy and, if
ence with and /or damage this product.
not installed and used in accordance with the instructions,
25-M-W-3
may cause harmful interference to radio communications.
Responsible Party: Panasonic Corporation of North America
However, there is no guarantee that interference will not
One Panasonic Way
occur in a particular installation. If this equipment does
Secaucus, NJ 07094
cause harmful interference to radio or television recepTel No:1-800-LAPTOP5 (1-800-527-8675)
tion, which can be determined by turning the equipment
6-M-1
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
FCC Regulation Notice for modem
z Reorient or relocate the receiving antenna.
This equipment contains a FCC approved modem.
z Increase the separation between the equipment and
receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
z Consult the Panasonic Service Center or an experi1. This equipment complies with CFR47 Part 68 rules.
enced radio/TV technician for help.
On the computer is a label that contains, among other
Read Me First
Useful Information
Getting Started
7. There are no user serviceable parts contained in this
equipment.
8. This equipment may not be used on coin service provided by the telephone company. Connection to party
lines is subject to state tariffs.
9. The Telephone Consumer Protection Act of 1991
makes it unlawful for any person to use a computer or
other electronic device to send any message via a
telephone fax machine unless such message clearly
contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission,
the date and time it is sent and an identification of the
business or other entry, or other individual sending the
message and the telephone number of the sending
machine or such business, other entity, or individual. In
order to program this information into your fax software, you should refer to the manual of the Fax software being used.
10.According to the FCC’s electrical safety advisory, we
recommend that you may install an AC surge arrestor
in the AC outlet to which this equipment is connected.
Telephone companies report that electrical surges,
typically lightning transients, are very destructive to
customer terminal equipment connected to AC power
sources and that this is a major nationwide problem.
“Caution : To reduce the risk of fire, use only No.26 AWG or
larger (e.g., 24 AWG) UL listed or CSA certified telecommunication line cord”
“ATTENTION : Pour reduire le risque d’fincendie, utiliser
uniquement des conducteurs de telecommunications 26
AWG ou de section superieure (p.ex. 24 AWG) UL
énumérés ou CSA certifié.”
16-M-1
Notice for the products using LCD
This product has a fluorescent lamp that contains mercury. Disposal may be regulated in your community due to
environmental considerations.
For disposal or recycling information, please contact your
local authorities, or the Electronic Industries Alliance:

24-M-1

This product contains a Coin Cell Lithium Battery
which contains Perchlorate Material- special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate/
38-M-1
Safety Precautions
Troubleshooting

The following safety precautions must be observed during all phases of the operation, usage, service or repair of any
Personal Computer or Handheld Computer incorporating Wireless WAN. Manufacturers of the cellular terminal are
advised to convey the following safety information to users and operating personnel and to incorporate these guidelines
into all manuals supplied with the product. Failure to comply with these precautions violates safety standards of design,
manufacture and intended use of the product. Panasonic assumes no liability for customer failure to comply with these
precautions.
When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch
Personal Computer or Handheld Computer incorporating Wireless WAN off, if instructed to do so by the
guidelines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of
cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by interference
from Personal Computer or Handheld Computer incorporating Wireless WAN placed close to the device. If in
doubt about potential danger, contact the physician or the manufacturer of the device to verify that the
equipment is properly shielded. Pacemaker patients are advised to keep their Personal Computer or
Handheld Computer incorporating Wireless WAN away from the pacemaker, while it is on.
Appendix
Switch off Personal Computer or Handheld Computer incorporating Wireless WAN before boarding an
aircraft. Make sure it cannot be switched on inadvertently. The operation of wireless appliances in an aircraft
is forbidden to prevent interference with communications systems. Failure to observe these instructions may
lead to the suspension or denial of cellular services to the offender, legal action, or both.
For details on usage of this unit in aircrafts please consult and follow instruction provided by the airline.
Do not operate Personal Computer or Handheld Computer incorporating Wireless WAN in the presence of
flammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots,
chemical plants or where blasting operations are in progress. Operation of any electrical equipment in
potentially explosive atmospheres can constitute a safety hazard.
Your Personal Computer or Handheld Computer incorporating Wireless WAN receives and transmits radio
frequency energy while switched on. Remember that interference can occur if it is used close to TV sets,
radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off
Personal Computer or Handheld Computer incorporating Wireless WAN wherever forbidden, or when you
suspect that it may cause interference or danger.
Road safety comes first! Do not use a Personal Computer or Handheld Computer incorporating Wireless
WAN while driving a vehicle. Do not place the computer with Wireless WAN in an area where it could cause
personal injury to the driver or passengers. It is recommended to stow the unit in the boot or secure stowage
area while driving. Do not place the computer with Wireless WAN in an area over an air bag or in the vicinity
where an air bag may deploy. Air bags inflate with great force and if the computer with Wireless WAN is
placed in the air bag deployment area may be propelled with great force and cause serious injury to
occupants of the vehicle.
IMPORTANT!
Personal Computer or Handheld Computer incorporating Wireless WAN operate using radio signals and
cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely solely
upon any wireless device for essential communications, for example emergency calls.
Getting Started
Remember, in order to make or receive calls, Personal Computer or Handheld Computer incorporating
Wireless WAN must be switched on and in a service area with adequate cellular signal strength.
Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g.
lock functions, fixed dialing etc.). You may need to deactivate those features before you can make an
emergency call.
Some networks require that a valid SIM card be properly inserted in Personal Computer or Handheld
Computer incorporating Wireless WAN.
27-1-2
“NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department
does not guarantee the equipment will operate to the user’s
satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some
situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment
malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural
areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.”
“NOTICE: The Ringer Equivalence Number (REN) assigned to
each terminal device provides an indication of the maximum
number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the
sum of the Ringer Equivalence Numbers of all the devices
does not exceed 5.”
REN: See bottom of the computer
“AVIS: L’étiquette d’Industrie Canada identifie le matériel
homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité
des réseaux de télécommunications, comme le prescrivent les
documents concernant les exigences techniques relatives au
matériel terminal. Le Ministère n’assure toutefois pas que le
matériel fonctionnera à la satisfaction de l’utilisateur.
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est
permis de le raccorder aux installations de l’entreprise locale
de télécommunication. Le matériel doit également être installé
en suivant une méthode acceptée de raccordement.
L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la
dégradation du service dans certaines situations.
Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur.
L’entreprise de télécommunications peut demander à l’utilisateur de débrancher un appareil à la suite de réparations ou
de modifications effectuées par l’utilisateur ou à cause de
mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurer que tous
les fils de mise à la terre de la source d’énergie électrique, des
lignes téléphoniques et des canalisations d’eau métalliques,
s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissement: L’utilisateur ne doit pas tenter de faire ces
raccordements lui-même; il doit avoir recours à un service
d’inspection des installations électriques, ou à un électricien,
selon le cas.”
“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à
chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une
combinaison de quelques dispositifs, à la seule condition que
la somme d’indices d’équivalence de la sonnerie de touts les
dispositifs n’excède pas 5.”
IES: Voir sous le fond de l’ordinateur
Troubleshooting
EQUIPMENT ATTACHEMENT LIMITATIONS
RESTRICTIONS CONCERNANT LE RACCORDEMENT
DE MATÉRIEL
Appendix

Industry Canada (IC) Notice for modem
This equipment contains an Industry Canada approved
modem unit.
The Industry Canada label is affixed on the modem unit.
Useful Information
Models for Canada
17-Ca-1
Read Me First
Canadian ICES-003
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
7-M-2
Getting Started

Industry Canada
This product complies with RSS-210 Industry Canada.
Operation is subject to the following two conditions;
(1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of
the device.
Useful Information

Industrie Canada
Cet equipement est conforme a la norme CNR-210
d’Industrie Canada. Son fonctionnement est soumis aux
deux conditions suivantes :
(1) ce dispositif ne peut produire de brouillage, et
(2) ce dispositif doit accepter le brouillage, y compris le
brouillage pouvant entrainer le fonctionnement non
desire de l’appareil.

This product (local network devices) for the band 51505250 MHz is only indoor usage to reduce potential for
harmful interference to co-channel Mobile Satellite systems.
High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 56505850 MHz and these radars could cause interference
and/or damage to LELAN devices.

Cet appareil (pour reseaux locaux radioelectriques) dans
les bandes de frequences 5150-5250 MHz est reserve a
une utilization a l’interieur afi n de reduire le risque d’nterference avec les systemes satellites mobiles bicanaux.
Les radars forte puissance sont designes comme etant
les premiers utilisateurs (c’est-a-dire qu’ils ont la priorite)
des bandes de frequences 5250-5350 MHz et 56505850 MHz. Ces stations radars peuvent provoquer des
interferences et/ou des dommages a ce peripherique.
30-Ca-2-1
30-Ca-1-1
Models for Europe

Troubleshooting
Declaration of Conformity (DoC)
“Hereby, Panasonic Corporation declares that this Personal Computer is in compliance with the
essential requirements and other relevant provisions of the Directive 1999/5/EC.”
Hint:
If you want to get a copy of the original DoC of our above mentioned products, please contact our
web address: http://www.doc.panasonic.de
Authorised Representative:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, Germany
Network connection of Wired Modem.
The terminal equipment is intended for connection to the following public network;
In all the countries of European Economical Area;
- Public Switched Telephony Networks
Appendix
Technical Features of Wired Modem.
The terminal equipment includes the following features;
- DTMF dialing
- Maximum bitrate receiving mode: 56 kbit/s
- Maximum bitrate sending mode: 33.6 kbit/s
18-E-1
Important Safety Instructions / Importantes Mesures De Sécurité
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near
a bath tub, wash bowl, kitchen sink or laundry tub, in a
wet basement or near a swimming pool.
2. Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk
of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the
vicinity of the leak.
4. Use only the power cord and batteries indicated in this
manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special
disposal instructions.
SAVE THESE INSTRUCTIONS
19-E-1
Certaines mesures de sécurité doivent être prises pendant l’utilisation de matérial téléphonique afin de réduire
les risques d’incendie, de choc électrique et de blessures.
En voici quelquesunes:
1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une
baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à
laver, dans un sous-sol humide ou près d’une piscine.
2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil
sans fil) pendant un orage électrique. Ceci peut présenter
un risque de choc électrique causé par la foudre.
3. Ne pas utiliser l’appareil téléphonique pour signaler
une fuite de gaz s’il est situé près de la fuite.
4. Utiliser seulement le cordon d’alimentation et le type de
piles indiqués dans ce manual. Ne pas jeter les piles
dans le feu: elles peuvent exploser. Se conformer aux
règlements pertinents quant à l’élimination des piles.
CONSERVER CES INSTRUCTIONS
19-F-1
Informations concernant la réglementation
Nous déclinons toute responsabilité pour toute interférence
radio ou télévision causée par des modifications non
autorisées apportées à ce produit. La correction d’interférences causées par de telles modifications non autorisées
sera la seule responsabilité de son utilisateur. Nousmêmes, les
revendeurs officiels et les distributeurs ne sommes pas responsable de tout dégât ou de toute violation des règlements de
l’État pouvant découler du non-respect de ces directives.
26-M-1
Useful Information
Regulatory Information
We are not responsible for any radio or television interference caused by unauthorized modification of this product.
The correction of interference caused by such unauthorized modification will be the responsibility of the user. We
and its authorized resellers or distributors are not liable for
damage or violation of government regulations that may
arise from failing to comply with these guidelines.
Troubleshooting

Ce produit et votre santé
Ce produit, comme tout autre appareil radio, émet de l’énergie
radioélectrique. Toutefois, la quantité d’énergie émise par ce
produit est beaucoup moins importante que l’énergie radioélectrique émise par des appareils sans fil tels que les téléphones
portables. L’utilisation de ce produit ne comporte aucun risque
pour le consommateur du fait que cet appareil opère dans les
limites des directives concernant les normes et les recommandations de sécurité sur les fréquences radio. Ces normes et
recommandations reflètent le consensus de la communauté scientifique et résultent de délibérations de jurys et comités de scientifiques qui examinent et interprètent continuellement les
nouveautés de la vaste littérature sur les recherches effectuées.
Dans certaines situations ou environnements, l’utilisation de ce
produit peut être restreinte par le propriétaire du bâtiment ou par
les représentants responsables de l’organisation. Ces situations
peuvent être les suivantes par exemple :
z A bord d’un avion, ou
z Dans tout autre environnement où les risques d’interférence sur d’autres appareils ou services sont perçus
ou identifiables comme dangereux.
Si vous n’êtes pas sûr de la réglementation applicable à
l’utilisation d’appareils sans fil dans une organisation ou
un environnement spécifique, (par exemple dans un
aéroport) nous vous invitons à demander l’autorisation
d’utiliser ce produit avant sa mise en marche.
Appendix

This product and your Health
This product, like other radio devices, emits radio frequency electromagnetic energy. The level of energy emitted by this product however is far much less than the
electromagnetic energy emitted by wireless devices like
for example mobile phones.
Because this product operates within the guidelines found
in radio frequency safety standards and recommendations,
we believe this product is safe for use by consumers. These
standards and recommendations reflect the consensus of
the scientific community and result from deliberations of
panels and committees of scientists who continually review
and interpret the extensive research literature.
In some situations or environments, the use of this product may be restricted by the proprietor of the building or
responsible representatives of the organization. These situations may for example include:
z Using this product on board of airplanes, or
z In any other environment where the risk of interference
to other devices or services is perceived or identified
as harmful.
If you are uncertain of the policy that applies on the use of
wireless devices in a specific organization or environment
(e.g. airports), you are encouraged to ask for authorization to use this product prior to turning on the product.
Getting Started
Information to the User / Informations destinées aux utilisateurs
26-F-1
Lithium Battery / Pile au lithium
Lithium Battery!
This computer contains a lithium battery to enable the
date, time, and other data to be stored. The battery should
only be exchanged by authorized service personnel.
Warning!
A risk of explosion from incorrect installation or misapplication may possibly occur.
15-E-1
Pile au lithium!
Le micro-ordinateur renferme une pile au lithium qui permet de sauvegarder certaines données, notamment la
date et l’heure. La pile ne doit être remplacée que par un
technicien qualifié.
Danger !
Risque d’explosion en cas de non respect de cette mise
en garde!
15-F-1
Read Me First
CD/DVD Drive Caution
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
12-E-1
AVERTISSEMENT!
Getting Started
CET APPAREIL UTILISE UN LASER.
L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉCUTION DE PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER UNE EXPOSITION À DES RADIATIONS
DANGEREUSES.
NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER
SOIMÊME.
CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.
12-1-1
12-F-1
Information on Disposal in other Countries outside the European Union
Useful Information
These symbols are only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask
for the correct method of disposal.
53-M-1
Precautions
Appendix
Troubleshooting
THIS PRODUCT IS NOT INTENDED FOR USE AS,
OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS,
AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS,
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*1,
MEDICAL DEVICES OR ACCESSORIES*2, LIFE
SUPPORT SYSTEMS OR OTHER EQUIPMENTS/
DEVICES/SYSTEMS THAT ARE INVOLVED WITH
ENSURING HUMAN LIFE OR SAFETY. PANASONIC
WILL NOT BE RESPONSIBLE FOR ANY LIABILITY
RESULTING FROM THE USE OF THIS PRODUCT
ARISING OUT OF THE FOREGOING USES.
*1
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS
include Class2 Electrical Flight Bag (EFB) Systems
and Class1 EFB Systems when used during critical
phases of flight (e.g., during take-off and landing)
and/or mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are defined by FAA: AC
(Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets) No.36.
*2 As defined by the European Medical Device Directive (MDD) 93/42/EEC. Panasonic cannot guarantee any specifications, technologies, reliability,
safety (e.g. Flammability/Smoke/Toxicity/Radio Frequency Emission, etc) requirements related to aviation standards and medical equipment standards
that differ from the specifications of our COTS
(Commercial-Off-The-Shelf) products.
If a Malfunction or Trouble Occurs, Immediately Stop
Use
If a Malfunction Occurs, Immediately Unplug the AC
Plug and the Battery Pack
• This product is damaged
• Foreign object inside this product
• Smoke emitted
• Unusual smell emitted
• Unusually hot
Continuing to use this product while any of the above conditions are present may result in fire or electric shock.
• If a malfunction or trouble occurs, immediately turn the
power off and unplug the AC plug, and then remove the
battery pack. Then contact your technical support office
for repair.
Do Not Touch This Product and Cable When It Starts
Thundering
Electric shock may result.
Do Not Connect the AC Adaptor to a Power Source
Other Than a Standard Household AC Outlet
Otherwise, a fire due to overheating may result. Connecting to a DC/AC converter (inverter) may damage the AC
adaptor. On an airplane, only connect the AC adaptor/
charger to an AC outlet specifically approved for such
use.
Do Not Place Containers of Liquid or Metal Objects on
Top of This Product
If water or other liquid spills, or if paper clips, coins, or foreign matter get inside this product, fire or electric shock
may result.
• If water spills in the keyboard, refer to page 20. If other
foreign matter has found its way inside, immediately turn
the power off and unplug the AC plug and remove the
battery pack. Then contact your technical support office.
Do Not Disassemble This Product
The high-voltage areas inside may give you an electric
shock, or foreign matter may enter and result in a fire.
Keep SD Memory Cards Away from Infants and Small
Children
Accidental swallowing will result in bodily injury.
• In the event of accidental swallowing, see a doctor
immediately.
Do Not Place This Product on Unstable Surfaces
If balance is lost, this product may fall over or drop, resulting in an injury.
Avoid Stacking
If balance is lost, this product may fall over or drop, resulting in an injury.
Do Not Keep This Product Wherever There is a Lot of
Water, Moisture, Steam, Dust, Oily Vapors, etc.
Otherwise, possibly resulting in fire or electric shock.
Do Not Leave This Product in High Temperature Environment for a Long Period of Time
Leaving this product where it will be exposed to extremely
high temperatures such as near fire or in direct sunlight
may deform the cabinet and/or cause trouble in the internal parts. Continued use in such a resulting condition may
lead to short-circuiting or insulation defects, etc. which
may in turn lead to a fire or electric shocks.
Do Not Block the Ventilation Hole
Otherwise, heat will build up inside, possibly resulting in a fire.
Hold the Plug When Unplugging the AC Plug
Pulling on the cord may damage the cord, resulting in a
fire or electric shock.
Take a Break of 10-15 Minutes Every Hour
Using this product for long periods of time may have detrimental health effects on the eyes or hands.
Getting Started
Insert the AC Plug Completely
If the plug is not inserted completely, fire due to overheating or electric shock may result.
• Do not use a damaged plug or loose AC outlet.
Do Not Subject the AC Adaptor to Any Strong Impact
Using the AC adaptor after a strong impact such as being
dropped may result in electric shock, short circuit, or fire.
Do Not Look into the CD/DVD Drive
Looking directly at the internal laser light source may
result in damage to eyesight.
Do Not Use Discs That Are Cracked or Deformed
Because the discs rotate at high speeds, damaged discs
may break apart causing injury.
• Discs that are not round and discs that have been
repaired using adhesives are similarly dangerous, and
so should not be used.
Useful Information
Clean Dust and Other Debris of the AC Plug Regularly
If dust or other debris accumulates on the plug, humidity,
etc. may cause a defect in the insulation, which may result
in a fire.
• Pull the plug, and wipe it with a dry cloth.
Pull the plug if the computer is not being used for a long
period of time.
Use Only the Specified AC Adaptor With This Product
Using an AC adaptor other than the one supplied (supplied with the unit or one sold separately as an accessory)
may result in a fire.
Do Not Turn the Volume Up to Loud When Using
Headphones
Listening at high volumes that overstimulate the ear for
long periods of time may result in loss of hearing.

Use the Modem with a Regular Telephone Line
Connection to an internal phone line (on-premise
switches) of a company or business office, etc. or to a digital public phone or use in a country or area not supported
by the computer may result in a fire or electric shocks.
Troubleshooting
Do Not Pull or Insert the AC Plug If Your Hands Are Wet
Electric shock may result.
Do Not Move This Product While the AC Plug Is Connected
The AC cord may be damaged, resulting in fire or electric
shock.
• If the AC cord is damaged, unplug the AC plug immediately.
Do Not Connect a Telephone Line, or a Network Cable
Other Than the One Specified, into the LAN Port
If the LAN port is connected to a network such as the
ones listed below, a fire or electric shock may result.
• Networks other than 1000BASE-T, 100BASE-TX or
10BASE-T
• Phone lines (IP phone (Internet Protocol Telephone),
Telephone lines, internal phone lines (on-premise
switches), digital public phones, etc.)
Do Not Use with Exposing the Skin to This Product
for a Long Period of Time
Using this product with exposing the skin to the heat
source of this product or AC adaptor for a long period of
time can cause a low-temperature burn.
Appendix
Do Not Do Anything That May Damage the AC Cord,
the AC Plug, or the AC Adaptor
Do not damage or modify the cord, place it near hot tools,
bend, twist, or pull it forcefully, place heavy objects on it,
or bundle it tightly.
Continuing to use a damaged cord may result in fire, short
circuit, or electric shock.
• For details on handling the cord of the AC adaptor, see
“Handling Cautions” (Î page 18).
z Do not place the computer near a television or radio
receiver.
z Keep the computer away from magnets. Data stored
on the hard disk may be lost.
z This computer is not intended for the display of images
for use in medical diagnosis.
z This computer is not intended for a use with connection of
medical equipment for the purpose of medical diagnosis.
z Panasonic shall not be liable for loss of data or other
incidental or consequential damages resulting from the
use of this product.
Read Me First
Precautions (Battery Pack)
Appendix
Troubleshooting
Useful Information
Getting Started
Do Not Use with Any Other Product
The battery pack is rechargeable and was intended for
the specified product. If it is used with a product other
than the one for which it was designed, electrolyte leakage, generation of heat, ignition or rupture may result.
10
z Should the battery leak and the fluid get into your
eyes, do not rub your eyes. Immediately flush your
eyes with clear water and see a doctor for medical
treatment as soon as possible.
Do Not Charge the Battery Using Methods Other Than
Those Specified
If the battery is not charged using one of the specified
methods, electrolyte leakage, generation of heat, ignition
or rupture may result.
CAUTION:
Risk of Explosion if Battery is replaced by an Incorrect Type.
Dispose of Used Batteries According to the Instructions.
Do Not Throw the Battery Pack into a Fire or Expose It
to Excessive Heat
Generation of heat, ignition or rupture may result.
z The battery pack may become warm during recharging or normal use. This is completely normal.
z Recharging will not commence if internal temperature
of the battery pack is outside of the allowable temperature range (0 °C to 55 °C {32 °F to 131 °F}). (Î
Reference Manual “Battery Power”)
Once the allowable range requirement is satisfied,
charging begins automatically. Note that the recharging time varies based on the usage conditions.
(Recharging takes longer than usual when the temperature is 10 °C {50 °F} or below.)
z In high-temperature environments, the battery takes
longer to fully recharge. In low-temperature environments, the battery takes longer to fully recharge and
the operating time is shorter. Only use the computer
within the allowable temperature range.
z The battery pack is a consumable item. If the amount
of time the computer can be run by using a particular
battery pack becomes dramatically shorter and
repeated recharging does not restore its performance,
the battery pack should be replaced with a new one.
z When transporting a spare battery inside a package,
briefcase, etc., it is recommended that it be placed in
a plastic bag so that its contacts are protected.
z Always power off the computer when it is not in use.
Leaving the computer on when the AC adaptor is not
connected will exhaust the remaining battery capacity.
Avoid Extreme Heat (Near the Fire, in Direct Sunlight,
for Example)
Electrolyte leakage, generation of heat, ignition or rupture
may result.
Do Not Insert Sharp Objects into the Battery Pack,
Expose It to Bumps or Shocks, Disassemble, or Modify It
Electrolyte leakage, generation of heat, ignition or rupture
may result.
• If this product is subjected to a strong impact, stop using
it immediately.
Do Not Short the Positive (+) and Negative (-) Contacts
Generation of heat, ignition or rupture
may result.
• Do not place the battery pack together
with articles such as necklaces or hairpins when carrying or storing.
Do Not Use This Product with a Battery Pack Other
Than the One Specified
Use only the specified battery pack (CF-VZSU56U) with
your product. Use of battery packs other than those manufactured and supplied by Panasonic may present a
safety hazard (generation of heat, ignition or rupture).
When the Battery Pack Has Deteriorated, Replace It
with a New One
Continued use of a damaged battery pack may result in
heat generation, ignition or battery rupture.
z Do not touch the terminals on the battery pack. The
battery pack may no longer function properly if the
contacts are dirty or damaged.
z Do not expose the battery pack to water, or allow it to
become wet.
z If the battery pack will not be used for a long period of
time (a month or more), charge or discharge (use) the
battery pack until the remaining battery level becomes
30% to 40% and store it in a cool, dry place.
z This computer prevents overcharging of the battery by
recharging only when the remaining power is less than
approx. 95% (when Economy Mode (ECO) is enabled:
75%) of capacity.
z The battery pack is not charged when the computer is
first purchased. Be sure to charge it before using it for
the first time. When the AC adaptor is connected to
the computer, charging begins automatically.
58-E-1
NOTE
A lithium ion battery that is recyclable powers the product you
have purchased.
Please call 1-800-8-BATTERY
for information on how to recycle
this battery.
L’appareil que vous vous êtes
procuré est alimenté par une batterie au lithium-ion.
Pour des renseignements sur le
recyclage de la batterie, veuillez
composer le 1-800-8-BATTERY.
48-M-1
Description of Parts
A :Speakers
B :Function Key
Î
Reference Manual “Key Combinations”
C :Keyboard
D :LED Indicator
: SD/SDHC Memory Card status
: Caps lock
: Numeric key (NumLk)
: Scroll lock (ScrLk)
: Hard disk drive status
ECO : Economy Mode (ECO) status
Î
Reference Manual “Battery Power”
I : CD/DVD Drive Power/Open Switch
• Slide the switch to the right to open the disc cover.
• Slide the switch to the left to turn on/off the drive power.
CD/DVD Drive Indicator
• Off: Drive power is off.
• Green: Drive power is on, but the drive is not accessed.
• Blinking green: Drive power is on, and the drive is
being accessed.
J : LCD
K :Security Lock
You can connect a Kensington cable. Refer to the instruction manual of the cable. The security lock and cable is a
theft prevention device. Panasonic Corporation will bear
no responsibility in the event of theft.
L : Modem Port
: Battery status
Î
Reference Manual “Modem”
:LAN
Port
Î
Reference Manual “Battery Power”
If the Mini Port Replicator is connected to the computer,
E : Power Switch
connect the LAN cable to the LAN port on the Mini Port
Î page 14
Replicator. You cannot use the LAN port on the computer.
Power Indicator
• Off: Power off/Hibernation
Î
Reference Manual “LAN”
• Green: Power on
N :External Display Port
• Blinking green:
Sleep/
Connect the cable of external display. When the mini
Standby
port replicator is connected, the connector for the mini
port replicator can also be used. Note that only up to 2
F : Wireless Switch
displays including the internal LCD can be displayed.
Switch the wireless devices to on (right side) or to off
(left side).
Î
Reference Manual “External Display”

O :USB Ports
Î
Reference Manual “Disabling/Enabling WireÎ
Reference Manual “USB Devices”
less Communication”
G :Latch
When closing the display, press down firmly from
above until the latch is firmly closed (locked).
H :CD/DVD Drive
Î
Reference Manual “CD/DVD Drive”
Useful Information
Troubleshooting
Appendix
Getting Started
CAUTION
When closing the disc
cover, press down the center of the disc cover (position indicated “CLOSE”) to
ensure that the cover is
locked.
11
Description of Parts
EXT. C
Appendix
Troubleshooting
Useful Information
Getting Started
A :Bluetooth Antenna

Î
Reference Manual “Bluetooth”
B :DC-IN Jack
C :Port Replicator Connector
Connect the Desktop Port Repliactor or Mini Port Replicator (optional).
Î
Reference Manual “Port Replicator”
D :Ventilation Hole
E : Microphone Jack
• When recording in stereo using a stereo microphone:
Î
Reference Manual “Wireless LAN”
J : Touch Pad
Î
Reference Manual “Using the Touch Pad”
K :Carrying Handle
L : Battery Latches
Î page 13
Click
(Start) - [Control Panel] - [Hardware and Sound] - [Sound]
- [Recording] - [Microphone] - [Properties], and then remove a check M :Battery Pack
Î page 13
mark of [Enable audio enhancements] in [Advanced].
Although the Operating Instructions for the CFVZSU56U battery pack (option) may indicate, “For use
Click [start] - [All Programs] - [SoundMAX] - [Control Panel]
and select [Microphone], and then add a check mark for
with I.T.E. Listed Notebook Computer, Panasonic,
[No Filtering] in [Microphone Enhancements].
Model CF-F8,” the CF-VZSU56U can also be used
• When using a monaural microphone with a 2-terminal plug:
with the CF-F9 series, in addition to the CF-F8 series.
Î
Reference Manual “Battery Power”
Click
(Start) - [Control Panel] - [Hardware and Sound] [Sound] - [Recording] - [Microphone] - [Properties], and then add N :Emergency Hole
a check mark for [Enable audio enhancements] in [Advanced].
Î
Reference Manual “CD/DVD Drive”
O :RAM Module Slot
Click [start] - [All Programs] - [SoundMAX] - [Control Panel]
Î
Reference Manual “Expanding Memory”
and select [Microphone], and then add a check mark for
*1
[Voice Recording] in [Microphone Enhancements]
SD/SDHC/SDXC Memory Cards are supF : Headphone Jack
ported.
You can connect headphones or amplified speakers.
When they are connected, audio from the internal
speakers is not heard.

Wireless WAN Antenna
SIM Card Slot
12
G :SD Memory Card Slot
Î
Reference Manual “SD/SDHC Memory Card”*1
H :PC Card Slot
Î
Reference Manual “PC Cards”
I : Î Wireless LAN Antenna

First-time Operation
„ Preparation
A Check and identify the supplied accessories.
If you do not find the described accessories, contact your technical support office.
• AC Adaptor . . . . 1
• AC Cord . . . . . . .1
• Battery Pack. . . 1
Model No: CF-AA6503A
Model No: CF-VZSU56U
Slide the battery pack in parallel with the arrow direction and attach it so that the
left and right dents (A) on the new battery pack match the projections (B) of the
computer.
In case that the dents does not match the projections of the computer, detach the
battery pack once, then slide it while pushing it lightly to avoid floating.
z To remove
Slide both the left and right latches to the
unlocked position, and push out the battery pack in parallel with the computer.
Battery
Latches
CAUTION
z Make sure the latches are securely locked. Otherwise the battery pack may fall
when you carry the computer.
z Do not touch the terminals of the battery pack and the computer. Doing so can
make the terminals dirty or damaged, and may cause malfunction of the battery
pack and the computer.
Open the display.
A Pull the carrying handle forward.
B Press and hold the latch (C) located at the front.
C Lift open the display.
Store the carrying handle, after you open the display.
CAUTION
z Do not open the display wider than necessary (140° or more), and do not apply
excessive pressure to the LCD. Do not open or close the computer holding the
edge of the LCD segment.
Useful Information
Insert the battery pack.
Troubleshooting
Appendix
B Read the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging
(Î page 28).
Getting Started
• Operating Instructions (This book) . . . . . . . . . . . . . . . . . . . . . . . . . . .1
• Product Recovery DVD-ROM Windows® 7 Professional . . . . . . . . .1
• Product Recovery DVD-ROM Windows® XP Professional SP3 . . . .1
13
First-time Operation
Connect your computer to a power outlet.
The battery charging starts automatically.
CAUTION
Troubleshooting
Useful Information
Getting Started
z Do not disconnect the AC adaptor and do not switch the wireless switch to
on until the first-time operation procedure is completed.
z When using the computer for the first time, do not connect any peripheral device
except the battery pack and AC adaptor.
z Handling the AC adaptor
• Problems such as sudden voltage drops may arise during periods of thunder
and lightning. Since this could adversely affect your computer, an uninterruptible power source (UPS) is highly recommended unless running from the battery pack alone.
Turn on the computer.
Slide and hold the power switch
power indicator
lights.
for approximately one second until the
CAUTION
z Do not slide the power switch repeatedly.
z The computer will forcibly be turned off if you slide and hold the power switch for
four seconds or longer.
z Once you turn off the computer, wait for ten seconds or more before you turn on
the computer again.
z Do not perform the following operation until the hard disk drive indicator
turns off.
• Connecting or disconnecting the AC adaptor
• Sliding the power switch or CD/DVD drive power/open switch
• Touching the keyboard or touch pad
• Closing the display
z Do not change the Setup Utility until completing step 5. If you do so, Windows
setup may not operate properly.
Setup Windows.
Follow the on-screen instructions.
z After the computer is turned on, the screen remains black or unchanged for a
while, but this is not a malfunction. Wait for a moment until the Windows
setup screen appears.
z Setup of Windows will take approximately 20 minutes.
Go to the next step, confirming each message on the display.
z “Join a wireless network” screen may not appear.
You can set the Wireless Network after the setup of Windows is complete.
Appendix
CAUTION
z Do not turn off the computer until completing the first-time operation procedure.
z You cannot choose the following words for user name and password: CON,
PRN, AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9.
Do not use an “@” mark for user name. If you create a user name that includes
an “@” mark, a password will be requested at the log-on screen, even if no password has been set. If you try to log on without entering a password, “The user
name or password is incorrect.” is displayed and you will not be able to log on to
Windows (Î page 26).
z You can change the user name, password, image and security setting after
setup of Windows.
z Remember your password. If you forget the password, you cannot use the Windows. Creating a password reset disk beforehand is recommended.
z When you set date/time/time zone and click [Next], the screen may not go to the
next step for a few minutes. Do not touch the keyboard, touch pad or touchscreen, and wait until the screen changes.
14
z When using the included stylus, avoid touching the screen with you hands, etc.
This can cause input errors.
z If “An unexpected error has occurred ...” (or a similar message) is displayed,
click [OK]. This is not a malfunction.
Create a new account.
Click [start] - [Control Panel] - [User Accounts] - [Create a new account].
CAUTION
Reference Manual “CD/DVD Drive”
NOTE
z PC Information Viewer
This computer periodically records the management information of the hard disk, etc. The maximum data volume for
each record is 1024 bytes.
This information is only used for estimating the cause when the hard disk goes down by any possibility. They are
never sent to outside via network nor used for any other purpose except for the purpose described the above.
To disable the function, add the check mark for [Disable the automatic save function for management information
history] in [Hard Disk Status] of PC Information Viewer, and click [OK].
When you disable the function, information on how to use the hard disk of PC Information Popup is not displayed.
(Î
Reference Manual “Check the Computer’s Usage Status” and “PC Information Popup”)
z If you hear the sounds from CD/DVD drive
In the following situations, the sounds from the CD/DVD drive can be heard.
• Immediately after the CD/DVD drive is turned on
• Just after turning on the computer with [Optical Drive Power] set to [On] in the Setup Utility
• When a CD or DVD is playing
The sounds you hear are normal operating sounds created by the motor in the CD/DVD drive operating; it is not a
malfunction.
z To conserve power, the following power saving methods are set at the time of purchase. (When AC adaptor
is connected)
• The screen automatically turns off after 15 minutes of inactivity.
• The computer automatically enters standby*1 after 20 minutes of inactivity.
*1
Refer to
Reference Manual “Standby or Hibernation Functions” about resuming from standby.
z Even when the AC adaptor is not connected to the computer, power is consumed (Max. 0.2 W) simply by
having the AC adaptor plugged into an AC outlet. (When using with 115 V AC)
z Note that the computer consumes electricity even when the computer power is off. If the battery pack is fully
charged, the battery will be fully discharged in the following period of time:
• In standby: Approx. 3 days (If “Wake Up from wired LAN” is enabled: 2 days)*2
• In hibernation: Approx.1.5 months (If “Wake Up from wired LAN” is enabled: 3 days)*2
• When power is off: Approx. 1.5 months (If “Power On by wired LAN” is enabled: 3 days)
*2
If “Wake Up from wired LAN” is disabled, the period of time will become slightly longer.
z When the CD/DVD drive power is turned off, the message “The ‘MATSHITA DVDXXXXXXXXX’ device can now be
safely removed from the system” will appear, but the CD/DVD drive is an internal device, so it cannot be removed.
Useful Information
Î
Troubleshooting
Change the internal CD/DVD drive letter if necessary.
Appendix
Getting Started
z Remember your password. If you forget the password, you cannot use the Windows
operation system. Creating a password reset disk beforehand is recommended.
15
First-time Operation
Appendix
Troubleshooting
Useful Information
Getting Started
„ When Starting Up/Shutting Down
z Do not do the following
• Connecting or disconnecting the AC adaptor
• Sliding the power switch or CD/DVD drive power/open switch
• Touching the keyboard, touch pad or external mouse
• Closing the display
16
„ To change the partition structure
You can shrink a part of an existing partition to create unallocated disk space, from which you can create a new partition.
This computer has a single partition in the default setting.
A Click
(Start) and right-click [Computer], then click [Manage].
z A standard user needs to enter an administrator password.
B Click [Disk Management].
C Right-click the partition for Windows (“c” drive in the default setting), and click [Shrink Volume].
z The partition size depends on the computer specifications.
z To select [Reinstall to the first 2 partitions.] in reinstalling Windows 7 (Î page 23), 30000 MB or more is necessary for [Total size after shrink in MB].
D Input the size in [Enter the amount of space to shrink in MB] and click [Shrink].
z You cannot input a larger number than the displayed size.
E Right-click [Unallocated] (the shrunk space in the step D) and click [New Simple Volume].
F Follow the on-screen instructions to make the settings, and click [Finish].
Wait until formatting is completed.
NOTE
z You can create an additional partition using remaining unallocated space or newly creating unallocated space.
z To delete a partition, right-click the partition and click [Delete Volume] in the step C.
On-screen Manual
You can access the following manuals on the computer screen after completing the “First-time Operation”.
When you access the on-screen manual for the first time, the License Agreement of the Adobe Reader may be displayed. Read it carefully and select [Accept] to proceed.
„ Reference Manual
The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.
To access the Reference Manual:
on the desktop.
Click [start] - [Reference Manual].
Alternatively click
(Start) /
- [Reference Manual].
[start] - [All Programs] - [Panasonic] - [On-Line Manuals]
„ Important Tips
The Important Tips will provide you with the helpful information about the battery. Read to use the battery pack in the
optimum condition to obtain longer operation time.
To access the Important Tips:
(Start) /
[start] - [All Programs] - [Panasonic] - [On-Line
„ Hard Disk Handling
The Hard Disk Handling will provide you with the helpful information on how to use the hard disk.
To access the Hard Disk Handling:
Click
(Start) /
Handling].
[start] - [All Programs] - [Panasonic] - [On-Line Manuals] - [Hard Disk
NOTE
z When Adobe Reader update notice is displayed, we recommend you follow the on-screen procedure to update.
See http://www.adobe.com/ for the latest version of Adobe Reader.
Troubleshooting
z Alternatively click
Manuals] - [Important Tips].
Useful Information
on the desktop.
Appendix
Double-click
Getting Started
Double-click
17
Handling and Maintenance
Getting Started
Operation Environment
z Place the computer on a flat stable surface. Do not place the computer upright. If the computer is exposed to an
extremely strong impact, it may become inoperable.
z Temperature: Operation: 5 °C to 35 °C {41 °F to 95 °F}
Storage: -20 °C to 60 °C {- 4 °F to 140 °F}
Humidity:
Operation: 30% to 80% RH (No condensation)
Storage: 30% to 90% RH (No condensation)
Even within the above temperature/humidity ranges, using for a long time in an extreme environment will result in
the product deterioration and will shorten the product life.
• Be sure to use the computer in an environment with sufficient heat ventilation.
- Avoid using the computer on a highly heat retentive surfaces (e.g., rubber pads and blankets). If possible, use
the computer on surfaces that can dissipate heat, such as a steel desk.
- Do not cover the computer with towels, keyboard covers, etc., as this prevents heat dissipation.
- When using the computer, always keep the display open. (Note, however, that closing the display while the computer is in use does not cause generation of heat, ignition, or other malfunctions.)
z Do not place the computer in the following areas, otherwise the computer may be damaged.
• Near electronic equipment. Image distortion or noise may occur.
• Near magnets or in magnetic fields.
• In extremely high or low temperature.
z As the computer can become hot during operation, keep it away from items that are sensitive to heat.
Appendix
Troubleshooting
Useful Information
Handling Cautions
This computer is designed to minimize shock to parts such as the hard disk drive, but no warranty is provided against
any trouble caused by shock. Be extremely careful when handling the computer.
z Note for the carrying handle
• Do not pull out and push the carrying handle when using the computer.
• When you store the carrying handle, take care you do not nip your finger between the handle and computer or at
both handle edges.
z When carrying the computer:
• Turn off the computer.
• Remove all external devices, cables, cards
and other protruding things.
• Remove a disc in the CD/DVD drive.
• Do not drop or hit the computer against solid
objects.
OK
NG
NG
• Do not leave the display open.
• Do not pick up or hold the computer by the
display part.
• Make sure the display is firmly closed when you carry
(A)
(B)
the computer with the handle.
z When you carry the AC adaptor with the cord rolled up,
roll it up as shown in (A).
Do not roll up the cord in the opposite direction or crossed
direction as shown in (B).
NG
NG
• Be sure not to roll up the cord around the AC adaptor in use.
• Pull out the AC cord. Also, do not roll up the AC cord.
z When you board an airplane, take the computer with you
and never put it in your checked luggage. When using the computer on airplane, follow the airline’s instructions.
z When carrying a spare battery, put it in a plastic bag to protect its terminals.
z This computer contains a magnet and magnetic products at the locations circled in the illustration at right. Avoid leaving metallic object or magnetic media in contact with these areas.
z The touch pad is designed to be used with a finger tip. Do not place any object on its surface and do not press down strongly with sharp-pointed or hard objects that may leave
marks (e.g., nails, pencils and ball point pens).
z Avoid any harmful substances such as oil from getting into the touch pad. The cursor
may not work correctly.
z If the computer is being carried in a soft bag with the battery pack removed, avoid undue pressure
on the body of the computer in a crowded place, etc., as this may result in damage to the LCD.
„ When the battery indicator does not light on
The AC adaptor’s protection function may be working when the battery indicator does not light on even if the AC adaptor and the battery pack are correctly connected with the computer.
z Pull out the AC cord and wait for more than 1 minute to reconnect the AC cord.
z If the problem persists, contact your technical support office.
18
„ If the computer becomes warm during usage
Click
on the notification area and click
. Then select [Panasonic Power management (Better Heat Dispersion)]
• When changing to [Panasonic Power management (Better Heat Dispersion)], the following settings will change.
- Change to [High Speed] from [Standard] in [Fan control mode].
Rotation of the cooling fan will become faster and the computer can be cooled down. Note that the battery operating time will be shorter.
- Switch the screen saver to [Prohibited].
• When you do not frequently use CPU or the rotation noise of the fan bothers you, set [Standard] or [Low Speed] in
[Fan control mode].
A Click
on the notification area and click
B Select [Standard] or [Low Speed] in [Fan control mode].
Double-click
on the desktop and click [High speed], then click [OK].
• When you set [High speed], rotation of the cooling fan speeds up and the computer can be cooled down. Note that
the battery operating time will be shorter.
• When you do not frequently use CPU or the rotation noise of the fan bothers you, set [Standard] or [Low speed] as
necessary.
„ When using peripheral devices
Follow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction
manuals of the peripheral devices.
z Use the peripheral devices conforming to the computer’s specifications.
z Connect to the connectors in the correct direction.
z If it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc.
z If screws are included, fasten them securely.
„ Preventing your computer from unauthorized use via wireless LAN/wireless WAN/Bluetooth

z Before using wireless LAN/wireless WAN/Bluetooth, make the appropriate security settings such as data encryption.
Useful Information
Reference Manual “Customizing the Power Setting”
Troubleshooting
Î
Getting Started
z Check the following
• If you are not using a wireless LAN, turn the wireless LAN off.
•
If the computer becomes warm while the screen saver is displayed, set the screen saver to [Windows XP]. Screen
savers that use 3-D images or other complex images increase the CPU utilization rate.
• Use recommended RAM module products. Non-recommended RAM modules may not operate properly, and may
cause damage to your computer.
To clean the LCD panel and touch pad
Wipe lightly with a gauze or other dry, soft cloth.
To clean areas other than the LCD panel and touch pad
Wet a soft cloth with water or a diluted kitchen cleanser (neutral), wring the cloth out thoroughly, and wipe the dirty area
gently. Using a detergent other than a neutral kitchen cleanser (e.g., a weak alkali cleanser) may adversely affect
painted surfaces.
Appendix
Maintenance
CAUTION
z Do not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc.
Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to
the surface.
z Do not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause
malfunction or damage.
19
Handling and Maintenance
When Using the Computer with a Reduced Screen Resolution
When setting the screen resolution to a resolution below the LCD’s resolution, e.g. 1024 × 768 pixels, the images
appearing on the screen will be stretched. As a result, the characters displayed may appear blurred. This is normal, and
not indicative of a malfunction.
Appendix
Troubleshooting
Useful Information
Getting Started
To display large characters with no blurring
Try the following steps while keeping the LCD in its resolution (1280 × 800).
z To display enlarged font sizes in applications such as Internet Explorer:
Use the display enlargement function provided by the specific software application.
z To display enlarged desktop icons, title bar and cursor or magnify the specific part of the screen:
Use “Icon Enlarger” or “Loupe Utility”.
If You Spill Water on the Keyboard
Note that repairs resulting from liquids being spilled on the computer are not free of charge, and not covered by warranty.
The keyboard on this computer incorporate a drain system (a moisture protection mechanism) that minimizes the
amount of liquid reaching the inside of the computer even if water is spilled on the keyboard.
Any water that comes in contact with the keyboard is drained off through holes in the bottom of the computer, so that virtually no water is left inside the computer. However, this is not a guarantee against damage to the hard disk or other
internal parts, or against the loss or deletion of data.
The drain system is incorporated into only the keyboard. It does not apply to any other components.
z If you spill water or any other liquid on the keyboard, even a small amount, be sure to perform the following steps.
Failure to perform these steps may result in damage to the computer. The drain system will not provide complete
protection against water entering the computer.
Immediately turn off the computer, and remove the AC adaptor.
Wipe any water droplets off of the top of the keyboard using a
soft, dry cloth.
Slowly lift up the computer, keeping it level,
and wipe any water coming out of the holes
on the bottom using a soft, dry cloth.
If the computer is tilted during this step, liquid may seep
inside the computer resulting in damage.
NG
Keeping the computer level, move
the computer to a dry place.
If the computer is placed back on the wet
surface, water may seep inside the computer
from the bottom.
NG
20
5
Insert the tip of a ball-point pen or other object into the emergency hole on the bottom of the computer, and move it in the
direction of the arrow to open the disc cover.
The computer should be kept level, without tilting, while the disc cover is being
opened. Move the computer to the edge of the desk or table to perform this operation.
Check to see whether there is any water inside the CD/DVD drive.
Be sure to contact your technical support office to have the computer checked for any
malfunctions.
Useful Information
Troubleshooting
Remove the battery pack.
Appendix
Getting Started
If there is water inside, wipe it using a soft, dry cloth.
21
Reinstalling Software
Reinstalling software will return the computer to the default condition. When you reinstall the software, the hard disk
data will be erased.
Back up important data to other media or an external hard disk before reinstallation.
CAUTION
Do not delete the partition with boot files on the hard disk.
The disk space in the partition is not available to store data.
Hard disk
Partition with boot files
Getting Started
Area usable by Windows
Preparation
z Prepare the Product Recovery DVD-ROM (included).
z Remove all peripherals.
z Connect the AC adaptor and do not remove it until installation is complete.
NOTE
z Even if reinstallation is performed, the number of times of DVD’s region code setting will not be reset.
The Setup Utility starts up.
z If the password is requested, enter the Supervisor Password.
Useful Information
Write down all of the contents of the Setup Utility and press F9.
At the confirmation message, select [Yes] and press Enter.
Press F10.
At the confirmation message, select [Yes] and press Enter.
The computer will restart.
Press F2 or Del while [Panasonic] boot screen is displayed.
The Setup Utility starts up.
z If the password is requested, enter the Supervisor Password.
Set the Product Recovery DVD-ROM into the CD/DVD drive.
Select the [Exit] menu, then select [MATSHITA XXXXX] in [Boot Override].
Press Enter.
The computer will restart.
Click [Reinstall Windows] and click [Next].
The License Agreement screen appears.
10
Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].
When reinstalling Windows 7 into hard disk installed from Windows 7:
Select the settings and click [Next].
z [Reinstall Windows to the whole Hard Disk to factory default.].
You will have two partitions.
z [Reinstall to the first 2 partitions.]*1.
Select this option when the hard disk has already been divided into several partitions. For how to create a new
partition, refer to “To change the partition structure” (Î page 16).
You can keep the partition structure.
*1
This does not appear if Windows cannot be reinstalled to the partition containing boot files and the area
usable by Windows.
Appendix
Troubleshooting
Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.
When reinstalling Windows 7 into hard disk installed from Windows XP:
Click [Next].
11
At the confirmation message, click [YES].
Reinstallation starts automatically. (It will take approximately 30 minutes.)
z Do not interrupt reinstallation, for example by turning off the computer. Otherwise reinstallation may become
unavailable as Windows may not start up or the data may be corrupted.
22
12
Remove the Product Recovery DVD-ROM, and then click [OK] to turn off the computer.
13
Turn on the computer.
z If the password is requested, enter the Supervisor Password.
14
Perform the “First-time Operation” (Î page 14).
15
Start the Setup Utility and change the settings as necessary.
16
Perform Windows Update.
Press 1 to execute [1. [Recovery]].
Select the settings.
When installing Windows XP into hard disk installed from Windows 7, select 1 or 2.
Do not select [3]: This option is only available when using Windows XP.
If you select [3]: an error may occur during the installation.
11
At the confirmation message, press Y.
Reinstallation starts automatically. (It will take approximately 30 - 40 minutes.)
z Do not interrupt reinstallation, for example by turning off the computer or pressing Ctrl + Alt + Del. Otherwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.
12
Remove the Product Recovery DVD-ROM, and then click [OK] to turn off the computer.
z If additional instructions are included with the computer, be sure to read them. It may be necessary to perform
additional operations during the following procedure.
13
Turn on the computer.
z If the password is requested, enter the Supervisor Password.
14
Perform the “First-time Operation” (Î page 14).
15
Start the Setup Utility and change the settings as necessary.
Useful Information
10
Troubleshooting
Press 1 to select [1. Yes, I agree to the provisions above and wish to continue!].
Appendix
Getting Started
The License Agreement screen appears.
z To cancel partway, press 0.
23
Troubleshooting (Basic)
Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the
“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact
your technical support office. You can also check the computer’s status in the PC Information Viewer (Î
Manual “Check the Computer’s Usage Status”).
„ Starting Up and Standby and Hibernation Mode
The computer does not
power on/
The power indicator or battery indicator is not lit.
Connect the AC adaptor.
Insert a fully charged battery.
Remove the battery pack and the AC adaptor, then connect them again.
If an additional RAM module has been inserted, remove the RAM module and check to
see if the RAM module is the recommended one.
z When the CPU temperature is high, the computer may not start up to prevent overheating of
the CPU. Wait until the computer cools down, and then turn the power on again. If the computer does not power on even after cooling down, contact your technical support office.
Windows does not start up.
z Remove all peripheral devices (e.g. USB memory).
z If an additional RAM module has been inserted, remove the RAM module and check to
see if the RAM module is the recommended one.
z If the power indicator is lit, slide the power switch for four seconds or longer to turn off,
then turn on again.
z Using the following procedure, start up in Safe Mode, and check the error details.
A Turn on the computer, and when the [Panasonic] boot screen disappears (after entering the password*1 if one is set) hold down F8.
B Release your finger when [Windows Advanced Options Menu] is displayed, and with
Ï or Ð, select [Safe Mode], then press Enter.
Follow the on-screen instructions.
Getting Started
Useful Information
Troubleshooting
Appendix
24
Reference
*1
Supervisor Password or User Password set with the Setup Utility
z Press F9 in the Setup Utility to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again.
After adding or changing the z Turn off the computer and remove the RAM module, then confirm whether the RAM
module has compliant to specification. When the RAM module has conformed to specifiRAM module, the power is
cation, install it again.
turned on but nothing is displayed on the screen.
Cannot boot from internal
CD/DVD drive.
z Make sure that the bootable CD/DVD is set properly.
z Start the Setup Utility, and confirm the following settings.
• [Optical Drive] is set to [Enabled] in the [Advanced] menu.
• [Optical Drive Power] is set to [On] in the [Main] menu.
• [Boot Option #1] is set to [CD/DVD Drive] in the [Boot] menu.
z When an external CD/DVD drive is connected, you cannot boot from the internal CD/
DVD drive.
You have forgotten the
password.
z Supervisor Password or User Password: Contact your technical support office.
z Administrator password:
• If you have another account with Administrator authority, log-on with it, then delete the
password for the problem account.
• If you have a password reset disk, click [Reset password] displayed after the password
input error, then follow the on-screen instructions to set a new password.
• If you have a password reset disk, you can reset the administrator password. Set the
disk and enter any wrong password, then follow the on-screen instructions and set a
new password.
• If you cannot do either of the above, you will need to reinstall (Î page 22) and setup
Windows.
“Remove disks or other
media. Press any key to
restart” or a similar message appears.
z A floppy disk is in the floppy disk drive and it does not contain system startup information. Remove the floppy disk and press any key.
z This message may appear with some devices connected to the USB port. Remove the
device or set [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.
z If the problem persists after removing the disk, it may be a hard disk failure. Perform the reinstallation and return the hard disk to its condition at the time of purchase. (Î page 22) If the
problem persists even after the reinstallation, contact your technical support office.
[Executing Battery Recalibration] screen appears.
z The Battery Recalibration was canceled before Windows was shut down last time. To
start up Windows, turn off the computer by the power switch, and then turn on.
„ Starting Up and Standby and Hibernation Mode
The computer will not automatically enter
sleep/
standby or hibernation.
z If you connect to a network using wireless LAN function, perform access point settings.
[Enter Password] does not
appear when resuming from
sleep /
standby
hibernation.
z Select [Enabled] in [Password On Resume] in the [Security] menu of the Setup Utility
(Î
Reference Manual “Setup Utility”).
z The Windows password can be used instead of the password set in the Setup Utility.
(Î
Reference Manual “Wireless LAN”)
When logging on (e.g.,
resuming the computer),
audio is distorted.
z Perform the following steps to change the audio settings to prevent audio output.
A Right-click the desktop and click [Personalize] - [Sounds].
B Remove the check mark from [Play Windows Startup sound], and click [OK].
A Click [start] - [Control Panel] - [Sounds, Speech, and Audio Devices] - [Sounds and
Audio Devices], and click [Sounds].
B Set [Windows Logon] and [Windows Logoff] to [(None)].
Cannot resume.
z One of the following operations may have been carried out.
• In
sleep/
standby mode, the AC adaptor or battery
pack was disconnected, or a peripheral was connected or disconnected.
• The power switch was slid for four seconds or longer to forcibly turn off the computer.
Slide the power switch to turn on the computer. Data not saved will be lost.
Other startup problems.
z Check to see if there was a disk error.
A Remove all peripheral devices including an external display.
Click
(Start) - [Computer] and right-click [Local Disk (C:)], and click [Properties].
Click [start] - [My Computer] and right-click [Local Disk (C:)], and click [Properties].
C Click [Tools] - [Check Now…].
• A standard user needs to enter an administrator password.
D Select the option in [Check disk options] and click [Start].
Useful Information
A Click [start] - [Control Panel] - [User Accounts] and select the account, ant set the
password.
B Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Option] [Advanced] and a check mark for [Prompt for password when computer resumes
from standby].
Troubleshooting
A Click
(Start) - [Control Panel] - [User Accounts and Family Safety] - [Add or
remove user accounts] and select the account, and set the password.
B Click
(Start) - [Control Panel] - [System and Security] - [Power Options] - [Require
a password on wakeup] and a check mark for [Require a password].
Getting Started
z If you do not use wireless LAN function, turn off wireless LAN function. (Î
Reference Manual “Disabling/Enabling Wireless Communication”)
z Make sure that you are not using any software that regularly accesses the hard disk.
Click [Schedule disk check] and restart the computer.
z Start the computer in Safe Mode and check the error details. (Î page 24 “Windows
does not start up”.)
„ Shutting Down
Windows does not shut
down.
z Remove all peripheral devices.
z Wait one or two minutes. It is not a malfunction.
Appendix
„ Password
Even after entering the password, a message appears
requesting to type it again.
z If
lights up, press NumLk to disable the ten-key mode, and then input.
z If
lights up, press Caps Lock to disable the Caps Lock mode, and then input.
25
Troubleshooting (Basic)
„ Password
Cannot log on to Windows.
(“The user name or password
is incorrect.” is displayed.)
z The user name (account name) includes an “@” mark.
If another user account exists:
Log on to Windows using another user account, and delete the account that
includes “@”. Then create a new account.
If no other account exists:
You need to reinstall Windows (Î page 23).
„ Display
Appendix
Troubleshooting
Useful Information
Getting Started
When the screen becomes
black for a moment.
26
z When you set [Intel(R) video driver power saving function] - [Intel(R) Display Power Saving Technology] of Power Plan Extension Utility to [Enabled], if you do the following operations, the screen becomes black for a moment, but this is not a malfunction. You can
use it.
• Adjust the brightness of the screen with Fn + F1 / Fn + F2.
• Remove and insert the AC adaptor.
While you are using motion video playback software, benchmark software for graphic, if error
screen is displayed or application software does not function normally, set [Intel(R) video
driver power saving function] - [Intel(R) Display Power Saving Technology] to [Disabled].
z When you set [Intel video driver power saving function (Intel(R) Display Power Saving Technology)] of Power Saving Utility to [Enable], if you do the following operations, the screen
becomes black for a moment, but this is not a malfunction. You can use it.
• Adjust the brightness of the screen with Fn + F1 / Fn + F2.
• Remove and insert the AC adaptor.
While you are using motion video playback software, benchmark software for graphic, if
error screen is displayed or application software does not function normally, set [Intel video
driver power saving function (Intel(R) Display Power Saving Technology)] to [Disable].
No display.
+ P) to switch the
z The external display is selected. Press Fn + F3 (or
display. Wait until the display has been switched completely before pressing Fn + F3
+ P) again.
(or
z The display is turned off by the power-saving function. To resume, do not press the direct
selection keys, but press any other key like Ctrl.
z The computer entered
sleep/
standby or hibernation by
the power-saving function. To resume, slide the power switch.
z The screen may become darker. Press Fn + F2 to make the screen brighter.
The screen is disordered.
z Changing the number of display colors and resolution may affect the screen. Restart the
computer.
z The refresh rate of the internal LCD may be 40 hertz. Change the refresh rate of the
internal LCD.
A Right-click on the desktop, and click [Graphics Properties].
B Click [General Settings].
C If [Refresh Rate] of the Notebook is [40 Hz], change to [60 Hz] and click [OK].
The external display does
not work normally.
z If the external display does not support the power saving function, it may not work normally when the computer enters the power saving mode. Turn off the external display.
„ Battery
The battery indicator is
lights red.
z The battery level is very low (the charge is approx. 9% or less).
z Connect the AC adaptor. You can use the computer when the indicator light is orange. If
you do not have an AC adaptor, save your data and power off your computer. After
replacing the battery pack with a fully charged one, turn your computer on again.
The battery indicator is
blinking.
z If blinking red:
Quickly save your data and power off your computer. Remove the battery pack and disconnect the AC adaptor, then connect them again. If the problem persists, contact your
technical support office. The battery pack or charging circuit may be defective.
z If blinking orange:
• Battery cannot be recharged temporarily because the internal temperature of the battery pack is outside the acceptable temperature range for recharging. Your computer
can be used normally in this state. Once the range requirement is satisfied, charging
begins automatically.
• Software applications and peripheral devices (USB devices, etc.) are consuming too
much power. Exit the software applications currently running, and remove all peripherals. Once the range requirement is satisfied, charging begins automatically.
„ Battery
The battery indicator is
flashing.
z The battery is recharging.
If [Battery Charging Indicator] in [Main] menu of the Setup Utility is set to [Flashing], the
indicator will alternately become lighter and darker.
„ Touch Pad
The cursor does not work.
z When using the external mouse, connect it correctly.
z Restart the computer by using the keyboard.
Press
and press Î two times, and press Ï to select [Restart] and press Enter.
The Reference Manual is not z Install Adobe Reader.
displayed.
A Log on to Windows as an administrator.
Click
(Start) and input “c:\util\reader\Setup.exe” in [Search programs and files]
then press Enter.
Click [start] - [Run] and input “c:\util\reader\Setup.exe”, then click [OK].
C Update Adobe Reader to its latest version.
D If your computer is connected to the internet, start up Adobe Reader and click [Help] [Check for Updates…].
„ Others
No response.
z Press Ctrl+Shift+Esc to open Task Manager and close the software application that
is not responding.
z An input screen (e.g., password input screen at startup) may be hidden behind another
window. Press Alt+Tab to check.
z Slide the power switch for four seconds or longer to shut down the computer, and then
slide the power switch to turn it on. If the application program does not work normally,
uninstall and reinstall the program. To uninstall,
click
(Start) - [Control Panel] - [Programs] - [Uninstall a program].
z click [start] - [Control Panel] - [Add or Remove Programs].
The computer does not recognize the CD/DVD drive.
Useful Information
„ Reference Manual
Troubleshooting
z Set [Touch Pad] to [Enabled] in the [Main] menu of the Setup Utility.
z The drivers for some mice may disable the touch pad. Check your mouse’s operating instructions.
z Restart the computer.
After the computer restarts, it may recognize a CD/DVD drive.
Appendix
Cannot input using the
touch pad.
Getting Started
z Press
, U, and R to select [Restart].
z If the computer does not respond to keyboard commands, read “No response” (Î below).
27
LIMITED USE LICENSE AGREEMENT
THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC PRODUCT (“PRODUCT”)
ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH
THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY
DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.
Panasonic Corporation has developed or otherwise obtained the Programs and hereby licenses their use to you. You
assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intended
results, and for the installation, use and results obtained therefrom.
Appendix
Troubleshooting
Useful Information
Getting Started
LICENSE
A. Panasonic Corporation hereby grants you a personal, non-transferable and non-exclusive right and license to use
the Programs in accordance with the terms and conditions stated in this Agreement. You acknowledge that you are
receiving only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no
title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which
title, ownership and rights shall remain with Panasonic Corporation or its suppliers.
B. You may use the Programs only on the single Product which was accompanied by the Programs.
C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not distribute or otherwise make the Programs or related documentation available to any third party, by time-sharing or otherwise, without the prior written consent of Panasonic Corporation.
D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for
any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your
use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or
attempt to modify, the Programs.
E. You may transfer the Programs and license them to another party only in connection with your transfer of the single
Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also
transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation,
to the same party or destroy any such copies not so transferred.
F. You may not remove any copyright, trademark or other notice or product identification from the Programs and you
must reproduce and include any such notice or product identification on any copy of any Program.
YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE
THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.
YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN
WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.
IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PERMITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.
TERM
This license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate
this license at any time by destroying, at your expense, the Programs and related documentation together with all copies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof
set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any
such termination, you agree to destroy, at your expense, the Programs and related documentation together with all copies thereof in any form.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND
BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT,
ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MATTER OF THIS AGREEMENT.
GOVERNMENT RESTRICTED RIGHTS.
The Software is provided with “RESTRICTED RIGHTS.” Use duplication or disclosure by the government is subject to
restrictions as set forth in FAR52.227-14 and DFAR252. 227-7013 et seq. or their successors.
Use of the Software by the government constitutes acknowledgement of Intel’s proprietary rights therein.
Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95052.
28
Contrat de licence d’usage limité
Le(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic (le “Produit”) sont exclusivement concédés en
licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles
cidessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et
conditions des présentes.
Panasonic Corporation a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par les présentes. Vous
assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour obtenir les résultats
escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus.
D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documentation
les accompagnant pour quelque fin que ce soit, à l’exception d’une (1) copie des Logiciels à des fins de sauvegarde
uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné par les Logiciels.
Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.
E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport avec votre cession du
Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez
céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les Logiciels
ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.
F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni aucune identification de
produit des Logiciels et vous devez reproduire et inclure toutes ces notices ou identifications de produit sur toutes
les copies des Logiciels.
Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs
copies, de façon électronique ou mécanique, en tout ou en partie.
Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie, à
l’exception de ce qui est expressément stipulé dans ce contrat.
Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé au
paragraphe E ci-dessus, votre licence est automatiquement résiliée.
Termes, clauses et conditions
Cette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation
antérieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation
les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée,
avec application immédiate, si les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous
ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de
détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme
que ce soit.
Useful Information
C. Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous ne pouvez ni
distribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage de
temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de Panasonic Corporation.
Troubleshooting
B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.
Appendix
A. Panasonic Corporation vous octroie par les présentes le droit et la licence personnels, non cessibles et non
exclusifs d’utiliser les Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez
ne recevoir qu’un droit limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à
n’obtenir aucun droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les
accompagnant ni vis-à-vis des algorithmes, concepts, dessins, configurations et idées représentés par ou
incorporés dans les Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous
à Panasonic Corporation ou à leurs propriétaires.
Getting Started
Licence
Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes,
clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu
entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre
communication entre nous, relativement à l’objet du présent contrat.
29
Specifications
To check CPU speed, memory size and the hard disk drive (HDD) size:
Start the Setup Utility (Î
Reference Manual “Setup Utility”) and select [Information] menu.
[Processor Speed]: CPU speed, [Memory Size]: Memory size, [Hard Disk]: Hard disk drive size
„ Main Specifications
Model No.
CF-F9KWHZZPM
CF-F9KWHZZDM
CPU
Intel® vPro™ Technology *1
CF-F9KWLZZPM
CF-F9KWLZZDM
Getting Started
Intel® Core™ i5-520M vPro™ processor (2.40 GHz with Turbo Boost up to 2.93 GHz,
Intel® Smart Cache 3 MB*1)
Chip Set
Mobile Intel® QM57 Express Chipset
Main Memory*3
2 GB*2,DDR3 SDRAM (4 GB*2 Max.)
Video Memory*4
UMA 763 MB Max. (When Memory is 2 GB) / UMA 1563 MB Max. (When Memory is 4 GB)
UMA 256 MB Max.
Video Controller
Intel® HD Graphics (Built-in CPU)
Hard Disk Drive*5
320 GB
Troubleshooting
Useful Information
Approx. 300 MB is used as a partition with recovery tools. (Users cannot use this partition.)
CD/DVD Drive
Continuous Data Transfer Speed*6*7
Supported Discs/Format*7
DVD MULTI Drive built-in, Buffer underrun error prevention function: Supported
Reading
zDVD-RAM*9: 5X (Max.)(4.7 GB)*5 zDVD-R*10: 8X (Max.) zDVD-RW: 8X (Max.)
zDVD-R DL: 8X (Max.) zDVD-ROM*8: 8X (Max.) zCD-ROM*8: 24X (Max.) zCD-R*8:
24X (Max.) zCD-RW: 24X (Max.) z+R: 8X (Max.) z+R DL: 8X (Max.) z+RW: 8X (Max.)
Writing*11
zDVD-RAM*9: 2X/3X/3-5X (4.7 GB)*5 zDVD-R: 2X/3.3-4X/3.3-6X/3.3-8X zDVD-RW:
1X/2X/2-4X/2-6X z+R: 2.4X/3.3-4X/3.3-6X/3.3-8X z+RW: 2.4X/2.4-4X zHigh Speed
+RW: 3.3X/3.3-6X zCD-R: 8X/8-12X/8-16X/10.8-24X zCD-RW: 4X zHigh-Speed CDRW: 4X/8X/10X
Reading
zDVD-ROM (Single Layer, Dual Layer) zDVD-Video zDVD-R*10 (1.4 GB, 2.8 GB,
4.7 GB)*5 zDVD-RW (Ver.1.1/1.2 1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 zDVD-R DL
(8.5 GB)*5 zDVD-RAM*9 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 z+R (4.7 GB)*5 z+R DL
(8.5 GB)*5 z+RW (4.7 GB)*5 zCD-Audio zCD-ROM (XA compatible) zCD-R zPhoto
CD (multiple session compatible) zVideo CD zCD EXTRA zCD-RW zCD-TEXT
Writing
zDVD-RAM*9 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 zDVD-R (1.4 GB, 2.8 GB, 4.7 GB for
General)*5 zDVD-RW (Ver.1.1/1.2 1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 z+R (4.7 GB)*5
z+RW (4.7 GB)*5 zCD-R zCD-RW
Display Method
14.1 WXGA+ type (TFT) (1440
Internal LCD
Appendix
× 900 dots)*12
65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1280 ×
1024 dots/1400 × 1050 dots/1440 × 900 dots/1680 × 1050 dots/1600 × 1200 dots/
1920 × 1080 dots/1920 × 1200 dots)
65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 768 dots/1440 ×
65,536/16,777,216 colors (1440
External Display*13
Simultaneous Display on LCD + External Display*13
Wireless LAN
900 dots)*12
Intel® Centrino® Advanced-N 6200*14 (Î page 31)
Î page 32
Bluetooth*15
IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T
LAN*16
Modem
Data: 56 kbps (V.92) FAX: 14.4 kbps
Fingerprint Reader
Sound
WAVE and MIDI playback, Intel® High Definition Audio subsystem support, Stereo
Speakers (built in)
Security Chip
TPM (TCG V1.2 compliant)*17
Card Slots
PC Card Slot
SD Memory Card
30
× 900 dots)
Slot*18
Array Size: 192 × 4 pixels, Image Size:
192 × 512 pixels, Image Resolution: 508
DPI
× 1, Type I or Type II, Allowable current 3.3 V: 400 mA, 5 V: 400 mA
×1
Model No.
CF-F9KWHZZPM
CF-F9KWHZZDM
RAM Module Slot
× 1, DDR3 SDRAM, 204-pin, 1.5 V, SO-DIMM, PC3-6400 Compliant*19
Interface
USB Ports × 3 (USB2.0 × 3)*20 / Modem Port (RJ-11) / LAN Port (RJ-45)*16 /
External Display Port: Mini Dsub 15-pin female / Microphone Jack*21: Miniature jack,
3.5 DIA / Headphone Jack: Miniature jack, 3.5 DIA / Port Replicator Connector: Dedicated 78-pin male*22
87 keys/Touch Pad
Keyboard/Pointing Device
Operating Time*24
Li-ion 10.8 V, 5.8 Ah (typ.), 5.4 Ah (min.)
Approx. 7 hours (Economy Mode (ECO) Disable)
Charging Time*25
Approx. 5 hours (Power off)/Approx. 6.5 hours (Power on)
Approx. 35 W*27 / Approx. 80 W (maximum when non-recharging in the ON state)
Physical Dimensions (W × D × H)
Weight*28
Environment
Operation Temperature
Humidity
Storage
326 mm × 251 mm × 25.5 mm (at the front)/48.5 mm (at the rear) {12.8 " × 9.9 " × 1.0 "
/ 1.9 "} (excluding protrusion)
Approx. 1.62 kg {3.6 lb.}
Approx. 1.63 kg {3.6 lb.}
5°C to 35°C {41°F to 95°F}
30% to 80% RH (No condensation)
Temperature
-20°C to 60°C {-4°F to 140°F}
Humidity
30% to 90% RH (No condensation)
OS*29
Genuine Windows® 7 Professional
Genuine Microsoft® Windows® XP Professional Service Pack 3
Pre-installed Software*29
Adobe Reader / Loupe Utility / Touch Pad Utility / PC Information Viewer / PC Information
Popup / Hotkey Settings / Wireless Switch Utility / Intel® Rapid Storage Technology /
Battery Recalibration Utility / WinDVD™ 8 (OEM Version) / Roxio Creator LJB / Optical
Disc Drive Letter-Setting Utility
Microsoft® Internet Explorer 8.0 / DirectX 11/ Microsoft® Windows® Media Player 12 /
Microsoft® .NET Framework 3.5.1 / Infineon TPM Professional Package V3.6*31 / Power
Plan Extension Utility
Microsoft® Internet Explorer 6 Service Pack 3 / DirectX 9.0c / Microsoft® Windows®
Media Player 10 / Microsoft® Windows® Movie Maker 2.1 / Microsoft® .NET Framework
3.5 SP1 / Intel® PROSet/Wireless Software / Icon Enlarger / Power Saving Utility / FAN
Control Utility / Wireless Connection Disable Utility*30 / Economy Mode (ECO) Setting
Utility / Infineon TPM Professional Package V3.5SP1*31 / Optical Disc Drive PowerSaving Utility
Bluetooth™ Stack for Windows by
Protector Suite*32
TOSHIBA*15
„ Wireless LAN 
Data Transfer Rates
IEEE802.11a : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*34
IEEE802.11b : 11/5.5/2/1 Mbps (automatically switched)*34
IEEE802.11g : 54/48/36/24/18/12/9/6 Mbps (automatically switched)*34
IEEE802.11n : (HT20) GI = 400 ns:144/130/115/86/72/65/57/43/39/28/21/14/7 GI = 800ns:130/117/
104/78/65/58/52/39/26/19/13/7 Mbps (automatically switched)*34
(HT40) GI = 400ns:300/270/240/180/150/135/120/90/60/30/15 GI = 800ns:270/243/
216/162/135/121/108/81/54/40/27/13 Mbps (automatically switched)*34
Standard Supported
IEEE802.11a / IEEE802.11b / IEEE802.11g / IEEE802.11n
Transmission Method
OFDM system, DS-SS system
Wireless Channels Used
IEEE802.11a : Channels 36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/157/
161/165
IEEE802.11b/IEEE802.11g : Channels 1 to 11
IEEE802.11n : Channels 1-11/36/40/44/48/52/56/60/64/100/104/108/112/116/132/136/140/149/153/
157/161/165
Useful Information
Power
Consumption*26
Approx. 6.5 hours (Economy Mode (ECO)
- Disable)
Troubleshooting
Battery Pack
Getting Started
AC adaptor or Battery pack
Input: 100 V - 240 V AC, 50 Hz/60 Hz
Output: 16 V DC, 5.0 A
AC Adaptor*23
Appendix
Power Supply
CF-F9KWLZZPM
CF-F9KWLZZDM
31
Specifications
„ Wireless LAN 
RF Frequency Band
IEEE802.11a : 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz, 5.745 GHz - 5.825 GHz
IEEE802.11b/IEEE802.11g : 2.412 GHz - 2.462 GHz
IEEE802.11n : 2.412 GHz - 2.462 GHz, 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz, 5.745 GHz 5.825 GHz
„ Bluetooth™ 
Bluetooth Version
2.1 + EDR
Transmission Method
FHSS system
Wireless Channels Used
Channels 1 to 79
RF Frequency Band
2.402 GHz - 2.48 GHz
Troubleshooting
Useful Information
Getting Started
*1
*2
*3
*4
*5
*6
*7
*8
*9
Appendix
*10
*11
*12
*13
*14
*15
*16
*17
32
The Intel® Active Management Technology (Intel® AMT)
function must be set before use.
1 MB = 1,048,576 bytes / 1 GB = 1,073,741,824 bytes
You can physically expand the memory up to 4 GB, but the
total amount of usable memory available will be less depending on the actual system configuration.
A segment of the main memory is allotted automatically
depending on the computer’s operating status. The size of
the Video Memory cannot be set by the user.
The size of Video memory is allotted depending on the operating system.
1 GB = 1,000,000,000 bytes. Your operating system or some
application software will report as fewer GB.
Data transfer speeds indicate values measured by
Panasonic Corporation. The data transfer rate of DVD per 1X
speed is 1,350 KB/s. The data transfer rate of CD per 1X
speed is 150 KB/s.
Performance of CD-R, CD-RW, DVD-RAM, DVD-R, DVD-R
DL, DVD-RW, +R, +R DL, and +RW cannot be guaranteed
depending on writing status and recording format. Also,
some data cannot be played back depending on the disc,
settings, and environment being used.
Does not support writing to DVD-R DL/+R DL (dual layer
discs) and Ultra-Speed CD-RW. Does not support 2.6 GB
DVD-RAM.
If an unbalanced disc (e.g., a disc with which the balance
has been displaced from the center) is inserted, the speed
may become slower if there are large vibrations while the
disc is rotating.
Only non-cartridge type or removable cartridge type can be
used.
DVD-R is compatible with 4.7 GB (for General) playback.
DVD-R (for Authoring) playback is compatible with discs
recorded using Disc-at-Once recording.
Depending on the disc, the writing speed may become slower.
A 16,777,216 color display is achieved by using the dithering
function.
Display may be impossible using some connected external
displays.
Only for model with wireless LAN.
Only for model with Bluetooth.
Some devices cannot be used depending on the port type.
Only for model that supports TPM.
For information on TPM, click
(Start) and
input “c:\util\drivers\tpm\README.pdf” in [Search programs
and files] and press Enter, and refer to the Installation
Manual of “Trusted Platform Module (TPM)”.
For information on TPM, click [start] - [Run]
and input “c:\util\drivers\tpm\README.pdf”, and refer to the
Installation Manual of “Trusted Platform Module (TPM)”.
*18
This slot is not compatible with the UHS-I high speed transfer. Operation has been tested and confirmed using Panasonic SD Memory Card with a capacity of up to 2 GB,
Panasonic SDHC Memory Card with a capacity of up to
*19
*20
*21
*22
*23
32 GB, and
Panasonic SDXC Memory Card
with a capacity of up to GB GB. Operation on other SD
equipment is not guaranteed.
Only a RAM module can be used (Panasonic : CFBAC02GU).
Does not guarantee operation of all USB-compatible peripherals.
Use a condenser-stereo microphone.
Port Replicator(optional).

The AC adaptor is compatible with power sources up to
240 V AC adaptor. This computer is supplied with a 125 V
AC compatible AC cord.
20-M-1-1
*24
Measured using MobileMark™ 2007 (LCD brightness :
60 cd/m2).
Varies depending on the usage conditions, or when an
optional device is attached.
When Economy Mode (ECO) is enabled, the operating time
becomes approximately 20% shorter than when it is disabled.
*25 Varies depending on the usage conditions, CPU speed, etc.
It may take a long time to charge a fully discharged battery.
*26 Approx. 0.9 W when the battery pack is fully charged (or not
being charged) and the computer is off.

Even when the AC adaptor is not connected to the computer,
power is consumed (Max. 0.2 W) simply by having the AC
adaptor plugged into an AC outlet.
*27 Rated power consumption.
23-E-1
*28
*29
*30
*31
*32
*33
*34
Average value. May differ depending on models.
Operations of this computer are not guaranteed except for
the pre-installed OS and the installed OS by using the Product Recovery DVD-ROM (included).
Some parts of the software in the Product Recovery DVDROM may not be installed depending on a model.
Must be installed before use.
Only for model that supports TPM.
Must be installed before use.
Only for model with fingerprint reader.
Must be installed before use.
The Product Recovery DVD-ROM is required.
These are speeds specified in IEEE802.11a+b+g+n standards. Actual speeds may differ.
LIMITED WARRANTY
For U.S.A.
Panasonic Solutions Company - Worldwide Product Warranties
Section 1 - Limited Warranty - Hardware
Battery Warranty
The battery supplied with the product is covered under the warranty for one (1) year from date of purchase, except as excluded in
Section 3. Batteries purchased separately are covered under the warranty for one (1) year from the date of purchase. A battery furnished under the warranty is covered for the remaining period of the one year warranty on the original or purchased battery.
Wireless Module Warranty
Panasonic approved wireless modems installed in Panasonic brand computers and integrated by Panasonic or an Authorized Panasonic Wireless Integrator are covered under the warranty for the remaining warranty period of the computer in which the modem is
installed. For computers with less than three (3) months remaining on the unit warranty, the wireless modem will be covered for a
period of three (3) months from the date of installation of the modem, covering only modem replacement or modem installation
related issues.
All modems must be approved by the wireless carrier prior to use. Any use or attempted use of a wireless modem not approved and
activated by the carrier for use on their network is strictly prohibited and is not sanctioned or warranted by Panasonic and may result
in legal action. In addition, all modems must be approved by Panasonic as compatible with the computer hardware before installation
or use.
Panasonic’s sole responsibility for the warranty or technical support of the software required to install or operate the modem is
defined in Section 2 (Limited Software Warranty). Any attempted software installation by anyone other than a Panasonic Authorized
Wireless Integrator is not covered under warranty and may result in service charges to re-image or replace the hard drive.
Installation or attempted installation by any party other than Panasonic or an Authorized Panasonic Wireless Integrator is strictly not
covered under the warranty and may void the computer warranty if damage results.
Useful Information
Laptop Computers - 3 Years
PDRC - LCD and Keyboard Assemblies - 3 Years
MDWD - Mobile Computer and Wireless Display Assemblies (CF-07/CF-08) - 3 Years
Ultra-Mobile PC (CF-U1/CF-H1) - 3 Years
Hand-held Computers (P1/P2) - 1 Year
Arbitrator Video Camera - 1 Year
Arbitrator Recorder Unit - 1 Year
Arbitrator Remote Control Panel - 1 Year
Arbitrator Wireless Receiver Unit - 1 Year
Arbitrator P2 Card(s) (All Sizes) - 1 Year
Arbitrator Wireless Microphone(s) / Transmitter - 90 Days
Arbitrator System Component Interconnect Cables - 90 Days
Troubleshooting
•
•
•
•
•
•
•
•
•
•
•
•
Getting Started
Panasonic Solutions Company (referred to as “Panasonic”) will repair the products listed below with new or rebuilt parts, free of
charge in the U.S.A. or other Panasonic approved location for the period specified below from the date of original purchase in the
event of a defect in materials or workmanship. These warranties are extended solely to the original purchaser. A purchase receipt or
other proof of date of original purchase will be required before warranty performance is rendered.
The below listed Panasonic brand or supplied options and accessories are covered under this limited warranty for the period specified from the date of purchase or as specifically stated:
•
•
•
•
•
•
•
•
•
•
•
•
AC Adaptor / Power Cord - 3 Years
Memory Card (Panasonic Brand) - 3 Years
Car Mount Docking Station PCB or Complete Vehicle Docking Station - 3 Years
Port Replicator / I-O Box / Device Cradle (like CF-08) - 3 Years
Antenna Pass-through Cable - 3 Years
Backlit or Full-sized keyboard - 3 Years or assumes warranty of the unit in which it is installed
Integrated Panasonic supplied options and kits including, but not limited to Wireless WAN, Media Bay Drives (Floppy, CD/DVD,
Combo), Camera, GPS, Bluetooth, Smartcard Reader, Magnetic Card Reader, Barcode Scanner and Fingerprint readers - 3
Years or assumes warranty period of the unit in which it is installed provided the integration was performed by Panasonic or an
Authorized Options Integrator.
Hard Drive (separately purchased) - 1 Year
External USB Drives (CD / DVD / Floppy / Hard Drive) - 1 Year
Optional Battery - 1 Year
Battery Charger / Multi-Bay Battery Charger - 1 Year
Digitizer pen or stylus - 90 Days (physical damage excluded)
Appendix
Options and Accessories warranties
33
LIMITED WARRANTY
Section 2 - Limited Warranty - Software
Panasonic Solutions Company (referred to as “Panasonic”) warrants to you only that the disk(s) or other media on which the Programs are furnished will be free from defects in material and workmanship under normal use for a period of sixty (60) days from the
date of delivery thereof to you, as evidenced by your purchase receipt.
This is the only warranty Panasonic makes to you. Panasonic does not warrant that the functions contained in the Programs will meet
your requirements or that the operation of the Programs will be uninterrupted or error free. Panasonic shall have no obligation for any
defects in the disk(s) or other media on which the Programs are furnished resulting from your storage thereof, or for defects that have
been caused by operation of the disk(s) or other media
Appendix
Troubleshooting
Useful Information
Getting Started
Panasonic’s entire liability and your exclusive remedy under this warranty shall be limited to the replacement, in the United States or
other Panasonic designated location, of any defective disk or other media which is returned to Panasonic’s Authorized Service Center, together with a copy of the purchase receipt, within the aforesaid warranty period. The customer is responsible for ensuring that
all data is backed up and made secure during normal use and before sending a unit for service.
Section 3 - Limited Warranty Exclusions
Specifically excluded from the warranty are:
• All consumable items; such as screen protection films, logo badges, labels, cleaning cloths, carry cases, manuals, cables,
straps, belts, holsters, tethers, and harnesses and any other options and accessories not listed above or covered under a separate warranty.
• Failures related to the product operating system, hard drive image, software setup, software program, virus, other program(s)
or file(s) on the hard drive or in any computer memory location.
• Failures due to BIOS settings or changes, as well as any cosmetic or physical damage to the unit.
• Any unit or device with a missing or altered model number or serial number label
• Damage which occurs in shipment
• Failures which are caused by products not supplied by Panasonic
• Failures which result from alteration, accident, misuse, introduction of liquid or other foreign matter into the unit, abuse, neglect,
installation, maladjustment of consumer controls, improper maintenance or modification, use not in accordance with product
use instructions
• Failures due to service by anyone other than a Panasonic Authorized Service Provider
• Failures caused by improper integration by any company other than Panasonic or a Panasonic Authorized Integrator.
• Damage, failure, or loss due to the unit being stolen, lost, misplaced, or used by anyone other than the original purchaser
• Damage that is attributable to acts of God
This warranty only covers failures due to defects in materials or workmanship which occur during normal use.
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*1. PANASONIC WILL NOT BE RESPONSIBLE
FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES.
*1 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems
when used during critical phases of flight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are defined by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets)
No.36
Other Limits and Exclusions: There are no other express warranties except as listed above.
PANASONIC SHALL NOT BE LIABLE FOR LOSS OF DATA OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS
AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations
or exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For technical support or to arrange for service on your Panasonic computer product, call our toll-free hotline at 1-800-LAPTOP5.
DIAL TOLL FREE: 1-800-LAPTOP5 (1-800-527-8675)
Web Site : www.panasonic.com/toughbook
34
For Canada
PANASONIC COMPUTER AND PERIPHERALS LIMITED WARRANTY
• Laptop Computers (except Battery) and AC Adaptor
• Factory/PCI installed options including Wireless WAN, GPS,
Bluetooth, Finger print reader, Backlit keyboard, Memory Card
and Media Bay Drives (Floppy, CD/DVD)
• Ultra-Mobile PC (CF-U1/CF-H1)
• Mobile Wireless Display oPDRC - LCD and Keyboard Assemblies
• Port Replicator
• Hand-held Computers
• Battery
• Battery charger
• Auto Adaptor
• External USB Drives
• Digitizer pen or stylus
Three (3) Years from Date of
Original End User Customer
Purchase
Defective Materials or Workmanship
One (1) Year from Date of
Original End User Customer
Purchase
Defective Materials or Workmanship
Ninety (90) Days from Date of Defective Materials or WorkmanOriginal End User Customer
ship
Purchase
• All consumable items including protection film, cleaning cloth, No Coverage
carry case, tether and harness
Remedy – In the event of a warranty claim, contact PCI’s representatives within the applicable warranty period, identifying the nature
of the defect claimed, at 1-800-668-8386 between 9:00 A.M. and 5:00 P.M., Eastern Time Zone, Mon. - Fri. (excluding holidays) for
instructions on how to obtain service. A purchase receipt or other proof of date of original purchase is required before warranty service is performed. Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts
on an exchange basis. Warranty replacement or repair is subject to the terms of this Limited Warranty for the balance of the original
period of warranty coverage.
No Coverage – This Limited Warranty does not cover products purchased outside Canada. Neither does it cover damage to, failure
of, or defects in a product or accessory through mishandling, improper installation, abnormal use, misuse, neglect, accident, introduction of liquid or other foreign matter into the product, alteration or servicing by anyone not authorized by PCI, or act of God.
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*2. PANASONIC WILL NOT BE RESPONSIBLE
FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES.
*2 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems
when used during critical phases of flight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are defined by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets)
No.36
IF YOU SHIP THE PRODUCT FOR WARRANTY SERVICE
Carefully pack the product, preferably in the original carton. Include details of defect claimed and proof of date of original purchase.
No liability is assumed for loss or damage to the product while in transit, if you chose your own transportation carrier.
SOFTWARE MEDIA LIMITED WARRANTY
Coverage – PCI warrants to you, the first end user customer, that the disk(s) or other media on which software program(s) is/are
supplied will be free from defects in materials and workmanship under normal use in Canada for a period of sixty (60) days from date
of receipt as evidenced by your purchase receipt for your Panasonic Computer product.
THIS IS THE ONLY WARRANTY THAT PCI MAKES RESPECTING THE SOFTWARE MEDIA. PCI does not warrant the software.
Please refer to the software licensor’s written warranty (accompanying the copy of the software) for any software warranty claim.
Claim Procedure – In the event of a defect in material or workmanship in the media during the sixty (60) days warranty period, and
you return it, transportation costs prepaid, to Panasonic Canada Inc., Computer Products Marketing, 5770 Ambler Drive, Mississauga, Ontario L4W 2T3, within the warranty period, together with a copy of your purchase receipt, and an explanation of the suspected defect, PCI will replace in Canada the defective disk(s) or other media.
Remedy – PCI’s entire liability, and your only remedy for any breach of this software media warranty is limited to replacement of the
media only. It does not cover any other damages, including, but not limited to, loss of use or profit loss, or special, indirect or consequential damages, or other claims, whether or not of similar character.
No Coverage – This limited warranty does not apply if the disk(s) or other media has been used in other than a Panasonic product,
or in environmental conditions other than those specified by PCI or the manufacturer, or if subjected to misuse, neglect, mishandling,
modification or attempted modification of the program, or if damaged by accident or act of God. PCI is not responsible for damage to
or loss of any program, data or removable storage media.
Useful Information
Type of Failure Coverage
Troubleshooting
Period of Coverage
Appendix
Scope of Coverage
Getting Started
Coverage – Panasonic Canada Inc. (“PCI”) warrants to you, the first end user customer, this computer product (excluding software
media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under normal use, subject to the terms set forth below, during the period of warranty coverage specified.
GENERAL
NO OTHER WARRANTIES - PCI DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH
RESPECT TO THE SOFTWARE, SOFTWARE MEDIA, COMPUTER PRODUCT, OPTIONS AND ACCESSORIES.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES - IN NO EVENT SHALL PCI BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES ARISING FROM ANY BREACH OF THE LIMITED WARRANTIES SET OUT IN THIS DOCUMENT,
OR FROM THE USE OF THE COMPUTER PRODUCT, INCLUDING, WITHOUT LIMITATION, LOSS OF DATA, BUSINESS,
PROFIT OR GOODWILL.
IN ANY EVENT, PCI’S MAXIMUM LIABILITY FOR ANY BREACH SHALL NOT EXCEED THE AMOUNT ACTUALLY PAID BY YOU
FOR THE COMPUTER PRODUCT.
NO ACTION, REGARDLESS OF ITS BASIS, MAY BE BEGUN AGAINST PCI MORE THAN TWO (2) YEARS AFTER THE CAUSE
OF ACTION AROSE.
Statutory Warranties – Some jurisdictions do not allow these limitations or exclusions, so they may not apply to you.
35
GARANTIE LIMITÉE
Pour le Canada
GARANTIE LIMITEE - ORDINATEURS ET PERIPHERIQUES PANASONIC
Appendix
Troubleshooting
Useful Information
Getting Started
Couverture – Panasonic Canada Inc. (« PCI ») garantit a l’acheteur original que ce produit informatique (a l’exclusion des supports des
logiciels) est, au moment de sa vente par PCI ou d’un revendeur agree par PCI, exempt de defauts de pieces et de fabrication dans les
conditions normales d’utilisation, et ce, pendant la periode de couverture de la garantie, sous reserve des modalites decrites ci-dessous.
Elements couverts
Duree de couverture
• Ordinateurs blocs-notes (sauf batteries) et adaptateur secteur
• Options installees en usine/par PCI incluant : WAN sans fil,
GPS, Bluetooth, lecteur d’empreintes digitales, clavier retroeclaire, carte memoire et lecteurs (disquettes, CD/DVD)
• Ordinateurs personnels ultra-portables (CF-U1/CF-H1)
• Ecran mobile sans fil
• Ensembles PDRC - ACL et clavier
• Duplicateur de port
• Ordinateurs de poche
• Batterie
• Chargeur de batterie
• Adaptateur pour voiture
• Peripheriques USB
• Stylo pointeur standard ou pour numeriseur graphique
Trois (3) ans a partir de la date Defauts de pieces et de fabricad’achat original.
tion
• Tous les articles consommables incluant les pellicules protectrices, chiffons de nettoyage, etuis de transport, longes et sangles
Un (1) an a partir de la date
d’achat original.
Type de couverture
Defauts de pieces et de fabrication
Quatre-vingt-dix (90) jours a
Defauts de pieces et de fabricapartir de la date d’achat original. tion
Aucune couverture
Recours – Pour obtenir des informations sur la marche a suivre dans le cas ou une reclamation en vertu de la garantie deviendrait necessaire, communiquez par telephone avec un representant de PCI au 1-800-668-8386, entre 9h00 et 17h00 (heure de l’Est) du lundi au
vendredi (sauf les jours feries), avant l’echeance de la garantie applicable, en prenant soin d’identifier la nature de la defaillance.
Un recu ou toute autre piece justificative de la date d’achat original sera exige avant toute reparation. Toute piece defectueuse couverte
par la presente garantie limitee sera reparee ou remplacee par une piece neuve ou remise a neuf. Le remplacement ou la reparation sera
fait conformement aux modalites de la presente garantie limitee pendant la duree restante de la periode originale de la garantie.
Produits non couverts – La presente garantie limitee ne couvre pas les produits achetes a l’exterieur du Canada. Elle ne couvre
pas non plus les dommages, la defaillance ou les defauts attribuables a une manutention inadequate, une mauvaise installation, une
utilisation anormale ou abusive, de la negligence, un accident, un deversement ou la penetration d’un objet etranger, une modification, un cas fortuit ou une reparation effectuee par une personne non agreee par PCI.
CE PRODUIT N’EST PAS DESTINE A ETRE UTILISE, EN TOUT OU EN PARTIE, COMME SYSTEME/EQUIPEMENT NUCLEAIRE, SYSTEME/
EQUIPEMENT DE CONTROLE DU TRAFFIC AERIEN OU SYSTEME/EQUIPEMENT DE POSTE DE PILOTAGE D’AVION*3. PANASONIC
DECLINE TOUTE RESPONSABILITE CONCERNANT L’UTILISATION DE CE PRODUIT DANS LES CAS SUSMENTIONNES.
*3 Les SYSTEMES/EQUIPEMENTS DE POSTE DE PILOTAGE D’AVION sont dotes de systemes OEPP (organiseur electronique
de poste de pilotage) de classe 2 et de classe 1 utilises pendant des phases critiques de vol (par exemple, pendant le decollage
et l’atterrissage) et(ou) montes sur l’avion. Les systemes OEPP de classe 1 et de classe 2 sont definis par le circulaire d’information FAA: AC (Advisory Circular) 120-76A ou le feuilet nº 36 JAA: JAA TGL (Temporary Guidance Leaflets) No 36.
EXPEDITION DU PRODUIT POUR SERVICE SOUS GARANTIE
Emballez soigneusement le produit, de preference dans son emballage d’origine. Joignez une description de la defaillance de
meme qu’une piece justificative de la date d’achat. Panasonic Canada Inc. ne peut etre tenue responsable pour tout dommage ou
perte subi pendant le transport si vous avez choisi le transporteur.
GARANTIE LIMITEE - SUPPORTS DES LOGICIELS
Couverture – Panasonic Canada Inc. (« PCI ») garantit a l’acheteur original que la ou les disquettes ou tout autre support sur lequel
le ou les programmes sont fournis sont exempts de defauts de pieces et de fabrication dans des conditions normales d’utilisation au
Canada, et ce, pour une periode de soixante (60) jours suivant la date de reception indiquee sur la preuve d’achat.
LA PRESENTE GARANTIE EST LA SEULE OFFERTE PAR PCI COUVRANT LES SUPPORTS DE LOGICIELS. PCI ne garantit
pas les logiciels. Reportez-vous a la garantie ecrite du concedant de licence d’utilisation du logiciel (qui accompagne la copie du
logiciel) pour toute reclamation en vertu de la garantie.
Réclamation – marche à suivre – Panasonic Canada Inc. remplacera toute disquette ou support defectueux si l’article en question est
retourne, port paye, a son service de Marketing - produits informatiques, 5770 Ambler Drive, Mississauga (Ontario) L4W 2T3, dans les soixante (60) jours suivant la date d’achat original. Joignez a votre envoi une piece justificative de votre achat et une description du probleme.
Recours –La responsabilite de PCI - et votre seul recours - dans le cas de toute defaillance couverte par la garantie sur ce support de
logiciel est limitee au seul remplacement du support. Elle ne couvre aucun autre dommage, y compris, mais non exclusivement, la perte
d’usage ou de profits, ni aucun dommage special, indirect ou consecutif, ni aucune autre reclamation de nature similaire ou autre.
Produits non couverts – La presente garantie limitee ne s’applique pas si la ou les disquettes ou autre support ont ete utilises dans
un produit d’une marque autre que Panasonic ou dans des conditions environnementales autres que celles specifiees par PCI ou le
fabricant, ou soumis a une mauvaise utilisation, a la negligence, a une manutention inadequate ou encore si le programme a ete modifie ou subi une tentative de modification ou des dommages attribuables a un accident ou a un cas fortuit. De plus, PCI n’assume
aucune responsabilite pour toute perte de, ou tout dommage a, un programme, des donnees ou un support de sauvegarde amovible.
GENERALITES
36
PCI NE RECONNAIT AUCUNE AUTRE GARANTIE, EXPLICITE OU IMPLICITE, Y COMPRIS, MAIS NON EXCLUSIVEMENT, LES
GARANTIES IMPLICITES DE VALEUR COMMERCIALE ET D’UTILITE A UNE FIN QUELCONQUE, A L’EGARD DU LOGICIEL,
SUPPORTS DE LOGICIELS, PRODUITS INFORMATIQUES, PERIPHERIQUES ET ACCESSOIRES.
SOUS AUCUNE CIRCONSTANCE PCI NE POURRA ETRE TENUE RESPONSABLE DES DOMMAGES SPECIAUX, INDIRECTS
OU CONSECUTIFS ATTRIBUABLES A UN MANQUEMENT AUX GARANTIES LIMITEES DECRITES DANS LE PRESENT DOCUMENT OU A L’UTILISATION DU PRODUIT INFORMATIQUE, Y COMPRIS, SANS RESTRICTION, LA PERTE DE DONNEES,
D’AFFAIRES, D’ACHALANDAGE OU DE PROFIT.
DANS TOUS LES CAS, LA RESPONSABILITE MAXIMALE DE PCI POUR TOUT MANQUEMENT NE POURRA EXCEDER LE
PRIX DE VENTE DU PRODUIT INFORMATIQUE.
AUCUNE RECLAMATION, SANS EGARD A SES MOTIFS, NE POURRA ETRE FAITE AUPRES DE PCI PLUS DE DEUX (2) ANS
APRES LES FAITS INVOQUES A LA BASE D’UNE TELLE RECLAMATION.
Garantie statutaires – Certaines juridictions interdisent de telles limitations ou exclusions; aussi, pourraient-elles ne pas s’appliquer.
MEMO
37
MEMO
38
39
As an ENERGY STAR® Partner, Panasonic Corporation has determined that
this product meets ENERGY STAR® guidelines for energy efficiency. By
enabling available power management settings, Panasonic computers enter
a low-power sleep mode after a period of inactivity, saving the user
energy. To learn more about power management, please visit the web site:
www.energystar.gov/index.cfm?c=power_mgt.pr_power_management
Outline of the International ENERGY STAR® Office Equipment Program
The international ENERGY STAR® Office Equipment Program is an international program that promotes energy
saving through the use of computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment such as computers,
displays, printers, facsimiles, and copiers. Their standards and logos are uniform among participating nations.
For information about ENERGY STAR®, refer to the following web side:
Web Site: www.energystar.gov
22-M-1
Panasonic Solutions Company
3 Panasonic Way, Panazip 2F-5,
Secaucus, NJ 07094
© Panasonic Corporation 2010
Printed in Japan
Panasonic Canada Inc.
5770 Ambler Drive Mississauga,
Ontario L4W 2T3
HS0510-0
DFQW5383ZA

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : Panasonic
Create Date                     : 2010:05:19 16:53:33Z
Modify Date                     : 2010:05:27 14:14:48-04:00
Subject                         : DFQW5383ZA
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : FrameMaker 7.1
Metadata Date                   : 2010:05:27 14:14:48-04:00
Format                          : application/pdf
Description                     : DFQW5383ZA
Title                           : Operating Instructions
Creator                         : Panasonic
Document ID                     : uuid:6331434d-2421-4c02-ab53-f6eb20dc2384
Instance ID                     : uuid:12f9e798-ff83-4564-b1e1-4276aae72ffa
Page Mode                       : UseNone
Page Count                      : 40

EXIF Metadata provided by EXIF.tools