Panasonic of North America 9TGCF-S91 Toughbook PC with WWAN, WLAN and Bluetooth User Manual Operating Instructions

Panasonic Corporation of North America Toughbook PC with WWAN, WLAN and Bluetooth Operating Instructions

UserManual.wiki >

Panasonic of North America >

9TGCF S91 User Manual

Users Manual

Please read these instructions carefully before using this product, and save this manual for future use.ContentsGetting StartedUseful InformationTroubleshootingGetting StartedUseful InformationTroubleshootingAppendixAppendixOPERATING INSTRUCTIONSPersonal ComputerModel No. CF-S9 seriesIntroduction.................................................2Read Me First ..............................................3(Precautions)Description of Parts .....................................11First-time Operation .....................................13On-screen Manual.......................................16Handling and Maintenance.............................17Reinstalling Software....................................20Troubleshooting (Basic) ................................22LIMITED USE LICENSE AGREEMENT..............25Specifications ............................................27LIMITED WARRANTY ..................................30For further information about the com-puter, you can refer to the on-screen manual.To access the on-screen manual Îpage 16 “On-screen Manual”For your technical support office, refer to “LIMITED WARRANTY.”

3Getting StartedUseful InformationTroubleshootingAppendixRead Me First<Only for model with a “ ” mark on the bottom of the computer>Federal Communications Commission Radio Fre-quency Interference StatementNote: This equipment has been tested and found to com-ply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-ence in a residential installation. This equipment gener-ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep-tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:zReorient or relocate the receiving antenna.zIncrease the separation between the equipment and receiver.zConnect the equipment into an outlet on a circuit differ-ent from that to which the receiver is connected.zConsult the Panasonic Service Center or an experi-enced radio/TV technician for help.WarningTo assure continued compliance, use only shielded inter-face cables when connecting to a computer or peripheral. Also, any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and(2)This device must accept any interference received, includ-ing interference that may cause undesired operation.FCC RF Exposure Warning:zThis equipment is provided with PC Card slot that could be used with wireless transmitters, which will be specif-ically recommended when they become available.Other third-party wireless transmitters have not been RF exposure evaluated for use with this computer and may not comply with FCC RF exposure requirements.<Only for model with wireless LAN/wireless WAN/Bluetooth>zThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.zThis equipment has been approved for mobile opera-tion, and unless otherwise advised in separate supple-mental instructions for individual wireless transmitter(s), requires minimum 20 cm spacing be provided between antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.zThis equipment may not be co-located or operated with any other antenna or transmitter.25-M-6<Only for model with wireless WAN>zThis product is restricted to indoor use due to its oper-ation in the 5.15 to 5.25 GHz frequency range.FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the poten-tial for harmful interference to co-channel Mobile Satel-lite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interfer-ence with and /or damage this product.25-M-W-3Responsible Party: Panasonic Corporation of North AmericaOne Panasonic WaySecaucus, NJ 07094Tel No:1-800-LAPTOP5 (1-800-527-8675)6-M-1FCC Regulation Notice for modemThis equipment contains a FCC approved modem.1. This equipment complies with CFR47 Part 68 rules. On the computer is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If required, this information must be provided to the tele-phone company.2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See Installation Instruc-tions for details.3.The REN is used to determine the quantity of devices which may be connected to the telephone line. Exces-sive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all area, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.4. If your telephone equipment cause harm to the tele-phone network, the telephone company will notify you in advice that temporary discontinuance of service may be required. But if advice notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.5. The telephone company may take changes in its facili-ties, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.6. If trouble is experienced with this equipment, for repair or warranty information, please contact Panasonic Corporation of North America at DIAL TOLL FREE 1-800-LAPTOP5 (1-800-527-8675). If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equip-ment until the problem is resolved.7. There are no user serviceable parts contained in this equipment.Models for U.S.A.

4Read Me FirstGetting StartedUseful InformationTroubleshootingAppendix8. This equipment may not be used on coin service pro-vided by the telephone company. Connection to party lines is subject to state tariffs.9. The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each trans-mitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entry, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. In order to program this information into your fax soft-ware, you should refer to the manual of the Fax soft-ware being used.10.According to the FCC’s electrical safety advisory, we recommend that you may install an AC surge arrestor in the AC outlet to which this equipment is connected. Telephone companies report that electrical surges, typically lightning transients, are very destructive to customer terminal equipment connected to AC power sources and that this is a major nationwide problem.“Caution : To reduce the risk of fire, use only No.26 AWG or larger (e.g., 24 AWG) UL listed or CSA certified telecommu-nication line cord”“ATTENTION : Pour reduire le risque d’fincendie, utiliser uniquement des conducteurs de telecommunications 26 AWG ou de section superieure (p.ex. 24 AWG) UL énumérés ou CSA certifié.”16-M-1<For USA-California Only><Only for model with wireless WAN>The following safety precautions must be observed during all phases of the operation, usage, service or repair of any Personal Computer or Handheld Computer incorporating Wireless WAN modem. Manufacturers of the cellular terminal are advised to convey the following safety information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the product. Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the product. Panasonic assumes no liability for customer failure to comply with these precautions.When in a hospital or other health care facility, observe the restrictions on the use of mobiles. Switch Personal Computer or Handheld Computer incorporating Wireless WAN modem off, if instructed to do so by the guidelines posted in sensitive areas. Medical equipment may be sensitive to RF energy. The operation of cardiac pacemakers, other implanted medical equipment and hearing aids can be affected by interference from Personal Computer or Handheld Computer incorporating Wireless WAN modem placed close to the device. If in doubt about potential danger, contact the physician or the manufacturer of the device to verify that the equipment is properly shielded. Pacemaker patients are advised to keep their Personal Computer or Handheld Computer incorporating Wireless WAN modem away from the pacemaker, while it is on.Switch off Personal Computer or Handheld Computer incorporating Wireless WAN modem before boarding an aircraft. Make sure it cannot be switched on inadvertently. The operation of wireless appliances in an aircraft is forbidden to prevent interference with communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular services to the offender, legal action, or both.For details on usage of this unit in aircrafts please consult and follow instruction provided by the airline.Do not operate Personal Computer or Handheld Computer incorporating Wireless WAN modem in the presence of flammable gases or fumes. Switch off the cellular terminal when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any electrical equipment in potentially explosive atmospheres can constitute a safety hazard.Your Personal Computer or Handheld Computer incorporating Wireless WAN modem receives and transmits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded equipment. Follow any special regulations and always switch off Personal Computer or Handheld Computer incorporating Wireless WAN modem wherever forbidden, or when you suspect that it may cause interference or danger.Road safety comes first! Do not use a Personal Computer or Handheld Computer incorporating Wireless WAN modem while driving a vehicle. Do not place the computer with Wireless WAN modem in an area where it could cause personal injury to the driver or passengers. It is recommended to stow the unit in the boot or secure stowage area while driving. Do not place the computer with Wireless WAN modem in an area over an air bag or in the vicinity where an air bag may deploy. Air bags inflate with great force and if the computer with Wireless WAN modem is placed in the air bag deployment area may be propelled with great force and cause serious injury to occupants of the vehicle.This product contains a Coin Cell Lithium Battery which contains Perchlorate Material- special han-dling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate/38-M-1Safety Precautions

5Getting StartedUseful InformationTroubleshootingAppendixIMPORTANT!Personal Computer or Handheld Computer incorporating Wireless WAN modem operate using radio signals and cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely solely upon any wireless device for essential communications, for example emergency calls.Remember, in order to make or receive calls, Personal Computer or Handheld Computer incorporating Wireless WAN modem must be switched on and in a coverage area with adequate cellular signal strength.Some networks do not allow for emergency calls if certain network services or phone features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate those features before you can make an emergency call.Some networks require that a valid SIM card be properly inserted in Personal Computer or Handheld Computer incorporating Wireless WAN modem.27-1-2<Only for model with modem>Industry Canada (IC) Notice for modemThis equipment contains an Industry Canada approved modem unit.The Industry Canada label is affixed on the modem unit.EQUIPMENT ATTACHEMENT LIMITATIONS“NOTICE: The Industry Canada label identifies certified equip-ment. This certification means that the equipment meets tele-communications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equip-ment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local tele-communications company. The equipment must also be installed using an acceptable method of connection. The cus-tomer should be aware that compliance with the above condi-tions may not prevent degradation of service in some situations.Repairs to certified equipment should be coordinated by a rep-resentative designated by the supplier. Any repairs or alter-ations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such con-nections themselves, but should contact the appropriate elec-tric inspection authority, or electrician, as appropriate.”“NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.”REN: See bottom of the computerRESTRICTIONS CONCERNANT LE RACCORDEMENTDE MATÉRIEL“AVIS: L’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est con-forme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement.L’abonné ne doit pas oublier qu’il est possible que la confor-mité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.Les réparations de matériel homologué doivent être coordon-nées par un représentant désigné par le fournisseur.L’entreprise de télécommunications peut demander à l’utili-sateur de débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement.Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’énergie électrique, des lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est par-ticulièrement importante dans les régions rurales. Avertisse-ment: L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d’inspection des installations électriques, ou à un électricien, selon le cas.”“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de ter-minaux qui peuvent être raccordés à une interface. La termi-naison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de touts les dispositifs n’excède pas 5.”IES: Voir sous le fond de l’ordinateur17-Ca-1Canadian ICES-003This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.7-M-2<Only for model with wireless LAN/Bluetooth>Industry CanadaThis product complies with RSS-210 Industry Canada.Operation is subject to the following two conditions;(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device.Models for Canada

6Read Me FirstGetting StartedUseful InformationTroubleshootingAppendix<Ne s’applique qu’aux modeles avec technologie Bluetooth/LAN sans fil>Industrie CanadaCet equipement est conforme a la norme CNR-210 d’Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes :(1) ce dispositif ne peut produire de brouillage, et(2) ce dispositif doit accepter le brouillage, y compris le brouillage pouvant entrainer le fonctionnement non desire de l’appareil.30-Ca-1-1<Only for model with wireless LAN>This product (local network devices) for the band 5150-5250 MHz is only indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite sys-tems.High power radars are allocated as primary users (mean-ing they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LELAN devices.<Ne s’applique qu’aux modeles avec technologie LAN sans fil>Cet appareil (pour reseaux locaux radioelectriques) dans les bandes de frequences 5150-5250 MHz est reserve a une utilization a l’interieur afi n de reduire le risque d’nter-ference avec les systemes satellites mobiles bicanaux.Les radars forte puissance sont designes comme etant les premiers utilisateurs (c’est-a-dire qu’ils ont la priorite) des bandes de frequences 5250-5350 MHz et 5650-5850 MHz. Ces stations radars peuvent provoquer des interferences et/ou des dommages a ce peripherique.30-Ca-2-1<Only for model with wireless LAN/wireless WAN/Bluetooth>zThis equipment complies with Industry Canada radia-tion exposure limits set forth for an uncontrolled envi-ronment.zThis equipment has been approved for mobile opera-tion, and unless otherwise advised separate supple-mental instructions for individual wireless transmitter(s), requires minimum 20 cm spacing be provided between antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.<Ne s’applique qu’aux modèles avec technologie Bluetooth/LAN sans fil/WAN sans fil>zCet équipement est conforme aux limites d’exposition aux rayonnements d’Industrie Canada établies pour un environnement non contrôlé.zCet équipement a été approuvé à des fins d’opération mobile et, sauf indication contraire, dans une notice supplémentaire concernant les émetteurs sans fil indi-viduels, doit être utilisé en veillant qu’il y ait une dis-tance d’au moins 20 cm entre son(ses) antenne(s) et le corps de l’utilisateur (sauf les extrémités : mains, poignets et pieds) dans les modes d’opération sans fil.<Only for model with a “CE” mark on the bottom of the computer>Declaration of Conformity (DoC)“Hereby, Panasonic declares that this Personal Computer is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.”Hint:If you want to get a copy of the original DoC of our above mentioned products, please contact our web address: http://www.doc.panasonic.deAuthorised Representative:Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg, GermanyNetwork connection of Wired Modem.The terminal equipment is intended for connection to the following public network;In all the countries of European Economical Area and Turkey;- Public Switched Telephony NetworksTechnical Features of Wired Modem.The terminal equipment includes the following features;- DTMF dialing- Maximum bitrate receiving mode: 56 kbit/s- Maximum bitrate sending mode: 33.6 kbit/s18-E-1<Only for model with modem>When using your telephone equipment, basic safety precau-tions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.3. Do not use the telephone to report a gas leak in the vicinity of the leak.4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.SAVE THESE INSTRUCTIONS19-E-1Models for EuropeImportant Safety Instructions / Importantes Mesures De Sécurité

7Getting StartedUseful InformationTroubleshootingAppendix<Pour modèles avec modem uniquement>Certaines mesures de sécurité doivent être prises pen-dant l’utilisation de matérial téléphonique afin de réduire les risques d’incendie, de choc électrique et de blessures. En voici quelquesunes:1. Ne pas utiliser l’appareil près de l’eau, p.ex., près d’une baignoire, d’un lavabo, d’un évier de cuisine, d’un bac à laver, dans un sous-sol humide ou près d’une piscine.2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appareil sans fil) pendant un orage électrique. Ceci peut présenter un risque de choc électrique causé par la foudre.3. Ne pas utiliser l’appareil téléphonique pour signaler une fuite de gaz s’il est situé près de la fuite.4. Utiliser seulement le cordon d’alimentation et le type de piles indiqués dans ce manual. Ne pas jeter les piles dans le feu: elles peuvent exploser. Se conformer aux règlements pertinents quant à l’élimination des piles.CONSERVER CES INSTRUCTIONS19-F-1<Only for model with wireless LAN/wireless WAN/Bluetooth>This product and your HealthThis product, like other radio devices, emits radio fre-quency electromagnetic energy. The level of energy emit-ted by this product however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.Because this product operates within the guidelines found in radio frequency safety standards and recommendations, we believe this product is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.In some situations or environments, the use of this prod-uct may be restricted by the proprietor of the building or responsible representatives of the organization. These sit-uations may for example include:zUsing this product on board of airplanes, orzIn any other environment where the risk of interference to other devices or services is perceived or identified as harmful.If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authoriza-tion to use this product prior to turning on the product.Regulatory InformationWe are not responsible for any radio or television interfer-ence caused by unauthorized modification of this product. The correction of interference caused by such unautho-rized modification will be the responsibility of the user. We and its authorized resellers or distributors are not liable for damage or violation of government regulations that may arise from failing to comply with these guidelines.26-M-1<Uniquement les modèles avec réseau local sans fil, réseau large sans fil et/ou Bluetooth>Ce produit et votre santéCe produit, comme tout autre appareil radio, émet de l’énergie radioélectrique. Toutefois, la quantité d’énergie émise par ce produit est beaucoup moins importante que l’énergie radioélec-trique émise par des appareils sans fil tels que les téléphones portables. L’utilisation de ce produit ne comporte aucun risque pour le consommateur du fait que cet appareil opère dans les limites des directives concernant les normes et les recomman-dations de sécurité sur les fréquences radio. Ces normes et recommandations reflètent le consensus de la communauté sci-entifique et résultent de délibérations de jurys et comités de sci-entifiques qui examinent et interprètent continuellement les nouveautés de la vaste littérature sur les recherches effectuées. Dans certaines situations ou environnements, l’utilisation de ce produit peut être restreinte par le propriétaire du bâtiment ou par les représentants responsables de l’organisation. Ces situations peuvent être les suivantes par exemple :zA bord d’un avion, ouzDans tout autre environnement où les risques d’inter-férence sur d’autres appareils ou services sont perçus ou identifiables comme dangereux.Si vous n’êtes pas sûr de la réglementation applicable à l’utilisation d’appareils sans fil dans une organisation ou un environnement spécifique, (par exemple dans un aéroport) nous vous invitons à demander l’autorisation d’utiliser ce produit avant sa mise en marche.Informations concernant la réglementationNous déclinons toute responsabilité pour toute interférence radio ou télévision causée par des modifications non autorisées apportées à ce produit. La correction d’inter-férences causées par de telles modifications non autorisées sera la seule responsabilité de son utilisateur. Nousmêmes, les revendeurs officiels et les distributeurs ne sommes pas respon-sable de tout dégât ou de toute violation des règlements de l’État pouvant découler du non-respect de ces directives.26-F-1Lithium Battery!This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service personnel.Warning! A risk of explosion from incorrect installation or misappli-cation may possibly occur.15-E-1Pile au lithium!Le micro-ordinateur renferme une pile au lithium qui per-met de sauvegarder certaines données, notamment la date et l’heure. La pile ne doit être remplacée que par un technicien qualifié.Danger ! Risque d’explosion en cas de non respect de cette mise en garde!15-F-1Information to the User / Informations destinées aux utilisateursLithium Battery / Pile au lithium

8Read Me FirstGetting StartedUseful InformationTroubleshootingAppendixCAUTION!THIS PRODUCT UTILIZES A LASER.USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.REFER SERVICING TO QUALIFIED PERSONNEL.12-E-1The following label is put on the bottom of the computer.AVERTISSEMENT!CET APPAREIL UTILISE UN LASER.L’UTILISATION DE COMMANDES OU DE RÉGLAGES OU L’EXÉCU-TION DE PROCÉDURES AUTRES QUE CELLES SPÉCIFIÉES ICI PEU-VENT PROVOQUER UNE EXPOSITION À DES RADIATIONS DANGEREUSES.NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE RÉPARER SOIMÊME.CONFIER TOUT TRAVAIL D’ENTRETIEN À UN PERSONNEL QUALIFIÉ.12-F-1L’étiquette suivante se trouve en-dessous de l’ordinateur.These symbols are only valid in the European Union.If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.53-M-1If a Malfunction or Trouble Occurs, Immediately Stop UseIf a Malfunction Occurs, Immediately Unplug the AC Plug and the Battery Pack• This product is damaged• Foreign object inside this product• Smoke emitted• Unusual smell emitted• Unusually hotContinuing to use this product while any of the above con-ditions are present may result in fire or electric shock.• If a malfunction or trouble occurs, immediately turn the power off and unplug the AC plug, and then remove the battery pack. Then contact your technical support office for repair.Do Not Touch This Product and Cable When It Starts ThunderingElectric shock may result.Do Not Connect the AC Adaptor to a Power Source Other Than a Standard Household AC OutletOtherwise, a fire due to overheating may result. Connect-ing to a DC/AC converter (inverter) may damage the AC adaptor. On an airplane, only connect the AC adaptor/charger to an AC outlet specifically approved for such use.CD/DVD Drive CautionInformation on Disposal in other Countries outside the European UnionPrecautionsTHIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS, AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*1, MEDICAL DEVICES OR ACCESSORIES*2, LIFE SUPPORT SYSTEMS OR OTHER EQUIPMENTS/DEVICES/SYSTEMS THAT ARE INVOLVED WITH ENSURING HUMAN LIFE OR SAFETY. PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES.*1 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems when used during critical phases of flight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Sys-tems and 2 EFB Systems are defined by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Tem-porary Guidance Leaflets) No.36.*2 As defined by the European Medical Device Direc-tive (MDD) 93/42/EEC. Panasonic cannot guarantee any specifications, tech-nologies, reliability, safety (e.g. Flammability/Smoke/Toxicity/Radio Frequency Emission, etc) requirements related to aviation standards and medical equipment standards that differ from the specifications of our COTS (Commercial-Off-The-Shelf) products.

9Getting StartedUseful InformationTroubleshootingAppendixDo Not Do Anything That May Damage the AC Cord, the AC Plug, or the AC AdaptorDo not damage or modify the cord, place it near hot tools, bend, twist, or pull it forcefully, place heavy objects on it, or bundle it tightly.Continuing to use a damaged cord may result in fire, short circuit, or electric shock.Do Not Pull or Insert the AC Plug If Your Hands Are WetElectric shock may result.Clean Dust and Other Debris of the AC Plug RegularlyIf dust or other debris accumulates on the plug, humidity, etc. may cause a defect in the insulation, which may result in a fire.• Pull the plug, and wipe it with a dry cloth.Pull the plug if the computer is not being used for a long period of time.Insert the AC Plug CompletelyIf the plug is not inserted completely, fire due to overheat-ing or electric shock may result.• Do not use a damaged plug or loose AC outlet.Do Not Place Containers of Liquid or Metal Objects on Top of This ProductIf water or other liquid spills, or if paper clips, coins, or for-eign matter get inside this product, fire or electric shock may result.• If water spills in the keyboard, refer to page 19. If other foreign matter has found its way inside, immediately turn the power off and unplug the AC plug and remove the battery pack. Then contact your technical support office.Do Not Disassemble This ProductThe high-voltage areas inside may give you an electric shock, or foreign matter may enter and result in a fire.Keep SD Memory Cards Away from Infants and Small ChildrenAccidental swallowing will result in bodily injury.• In the event of accidental swallowing, see a doctor immediately.Do Not Place This Product on Unstable SurfacesIf balance is lost, this product may fall over or drop, result-ing in an injury.Avoid StackingIf balance is lost, this product may fall over or drop, result-ing in an injury.Do Not Keep This Product Wherever There is a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc.Otherwise, possibly resulting in fire or electric shock.Do Not Leave This Product in High Temperature Envi-ronment for a Long Period of TimeLeaving this product where it will be exposed to extremely high temperatures such as near fire or in direct sunlight may deform the cabinet and/or cause trouble in the inter-nal parts. Continued use in such a resulting condition may lead to short-circuiting or insulation defects, etc. which may in turn lead to a fire or electric shocks.Do Not Block the Ventilation HoleOtherwise, heat will build up inside, possibly resulting in a fire.Hold the Plug When Unplugging the AC PlugPulling on the cord may damage the cord, resulting in a fire or electric shock.Do Not Move This Product While the AC Plug Is Con-nectedThe AC cord may be damaged, resulting in fire or electric shock.• If the AC cord is damaged, unplug the AC plug immedi-ately.Use Only the Specified AC Adaptor With This ProductUsing an AC adaptor other than the one supplied (sup-plied with the unit or one sold separately as an accessory) may result in a fire.Do Not Subject the AC Adaptor to Any Strong ImpactUsing the AC adaptor after a strong impact such as being dropped may result in electric shock, short circuit, or fire.Take a Break of 10-15 Minutes Every HourUsing this product for long periods of time may have detri-mental health effects on the eyes or hands.Do Not Look into the CD/DVD DriveLooking directly at the internal laser light source may result in damage to eyesight.Do Not Use Discs That Are Cracked or DeformedBecause the discs rotate at high speeds, damaged discs may break apart causing injury.• Discs that are not round and discs that have been repaired using adhesives are similarly dangerous, and so should not be used.Do Not Turn the Volume Up to Loud When Using HeadphonesListening at high volumes that overstimulate the ear for long periods of time may result in loss of hearing.<Only for model with modem>Use the Modem with a Regular Telephone LineConnection to an internal phone line (on-premise switches) of a company or business office, etc. or to a dig-ital public phone or use in a country or area not supported by the computer may result in a fire or electric shocks.Do Not Connect a Telephone Line, or a Network Cable Other Than the One Specified, into the LAN PortIf the LAN port is connected to a network such as the ones listed below, a fire or electric shock may result.• Networks other than 1000BASE-T, 100BASE-TX or 10BASE-T• Phone lines (IP phone (Internet Protocol Telephone), Telephone lines, internal phone lines (on-premise switches), digital public phones, etc.)Do Not Use with Exposing the Skin to This Product for a Long Period of TimeUsing this product with exposing the skin to the heat source of this product or AC adaptor for a long period of time can cause a low-temperature burn.zDo not place the computer near a television or radio receiver.zKeep the computer away from magnets. Data stored on the hard disk may be lost.zThis computer is not intended for the display of images for use in medical diagnosis.zThis computer is not intended for a use with connection of medical equipment for the purpose of medical diagnosis.zPanasonic shall not be liable for loss of data or other incidental or consequential damages resulting from the use of this product.

10Read Me FirstGetting StartedUseful InformationTroubleshootingAppendixDo Not Use with Any Other ProductThe battery pack is rechargeable and was intended forthe specified product. If it is used with a product otherthan the one for which it was designed, electrolyte leak-age, generation of heat, ignition or rupture may result.Do Not Charge the Battery Using Methods Other ThanThose SpecifiedIf the battery is not charged using one of the specifiedmethods, electrolyte leakage, generation of heat, ignitionor rupture may result.Do Not Throw the Battery Pack into a Fire or Expose Itto Excessive HeatGeneration of heat, ignition or rupture may result.Avoid Extreme Heat (Near the Fire, in Direct Sunlight,for Example)Electrolyte leakage, generation of heat, ignition or rupturemay result.Do Not Insert Sharp Objects into the Battery Pack,Expose It to Bumps or Shocks, Disassemble, or Modify ItElectrolyte leakage, generation of heat, ignition or rupturemay result.• If this product is subjected to a strong impact, stop using it immediately.Do Not Short the Positive (+) and Negative (-) ContactsGeneration of heat, ignition or rupture may result. • Do not place the battery pack together with articles such as necklaces or hairpins when carrying or storing.Do Not Use This Product with a Battery Pack OtherThan the One SpecifiedUse only the specified battery pack (CF-VZSU61U) withyour product. Use of battery packs other than those man-ufactured and supplied by Panasonic may present asafety hazard (generation of heat, ignition or rupture).When the Battery Pack Has Deteriorated, Replace Itwith a New OneContinued use of a damaged battery pack may result inheat generation, ignition or battery rupture.zDo not touch the terminals on the battery pack. The battery pack may no longer function properly if the contacts are dirty or damaged.zDo not expose the battery pack to water, or allow it to become wet.zIf the battery pack will not be used for a long period of time (a month or more), charge or discharge (use) the battery pack until the remaining battery level becomes 30% to 40% and store it in a cool, dry place.zThis computer prevents overcharging of the battery by recharging only when the remaining power is less than approx. 95% (when Economy Mode (ECO) is enabled: 75%) of capacity.zThe battery pack is not charged when the computer is first purchased. Be sure to charge it before using it for the first time. When the AC adaptor is connected to the computer, charging begins automatically.zShould the battery leak and the fluid get into your eyes, do not rub your eyes. Immediately flush your eyes with clear water and see a doctor for medical treatment as soon as possible.NOTEzThe battery pack may become warm during recharg-ing or normal use. This is completely normal.zRecharging will not commence if internal temperature of the battery pack is outside of the allowable temper-ature range (0 °C to 55 °C {32 °F to 131 °F}). (Î Reference Manual “Battery Power”) Once the allowable range requirement is satisfied, charging begins automatically. Note that the recharg-ing time varies based on the usage conditions. (Recharging takes longer than usual when the tem-perature is 10 °C {50 °F} or below.)zIn high-temperature environments, the battery takes longer to fully recharge. In low-temperature environ-ments, the battery takes longer to fully recharge and the operating time is shorter. Only use the computer within the allowable temperature range.zThe battery pack is a consumable item. If the amount of time the computer can be run by using a particular battery pack becomes dramatically shorter and repeated recharging does not restore its performance, the battery pack should be replaced with a new one. zWhen transporting a spare battery inside a package, briefcase, etc., it is recommended that it be placed in a plastic bag so that its contacts are protected.zAlways power off the computer when it is not in use. Leaving the computer on when the AC adaptor is not connected will exhaust the remaining battery capacity.Precautions (Battery Pack)CAUTION:Risk of Explosion if Battery is replaced by an Incorrect Type.Dispose of Used Batteries According to the Instructions.58-E-1A lithium ion battery that is recy-clable powers the product you have purchased.Please call 1-800-8-BATTERY for information on how to recycle this battery.L’appareil que vous vous êtes procuré est alimenté par une bat-terie au lithium-ion.Pour des renseignements sur le recyclage de la batterie, veuillez composer le 1-800-8-BATTERY.48-M-1

11Getting StartedUseful InformationTroubleshootingAppendixDescription of PartsA :SpeakersB :Function KeyÎ Reference Manual “Key Combinations”C :KeyboardD :LED Indicator : Caps lock : Numeric key (NumLk) : Scroll lock (ScrLk) : Hard disk and CD/DVD drive status : SD/SDHC/SDXC Memory Card statusECO : Economy Mode (ECO) statusÎ Reference Manual “Battery Power” : Battery statusÎ Reference Manual “Battery Power”E : Power SwitchÎpage 14Power Indicator• Off: Power off/Hibernation• Green: Power on • Blinking green: Sleep/StandbyF : Wireless SwitchSwitch the wireless devices to on (right side) or to off (left side).<Only for model with wireless LAN/wireless WAN/Bluetooth>Î Reference Manual “Disabling/Enabling Wire-less Communication”G :Fingerprint Reader<Only for model with Fingerprint Reader>Î Reference Manual “Fingerprint Reader”H :LCDI : Security LockYou can connect a Kensington cable. Refer to the instruc-tion manual of the cable. The security lock and cable is a theft prevention device. Panasonic Corporation will bear no responsibility in the event of theft.J : External Display PortConnect the cable of external display.K :USB PortsÎ Reference Manual “USB Devices”L : PC Card SlotÎ Reference Manual “PC Card”M :SD Memory Card SlotÎ Reference Manual “SD/SDHC Memory Card”*1 N :CD/DVD Drive Power/Open Switch• Slide the switch to the right to open the disc cover.• Slide the switch to the left to turn on/off the drive power.CD/DVD Drive Indicator• Off: Drive power is off or the disc cover is opened.• Green: Drive power is on.O :CD/DVD DriveÎ Reference Manual “CD/DVD Drive”*1 SD/SDHC/SDXC Memory Cards are supported.IJKLHABCDEFGMNO

12Description of PartsGetting StartedUseful InformationTroubleshootingAppendixBAGHKJICDEFA :Modem Port<Only for model with modem>Î Reference Manual “Modem”B :LAN PortÎ Reference Manual “LAN”C :DC-IN JackD :Ventilation Hole (Exhaust)E :HDMI PortÎ Reference Manual “External Display”F : USB PortsÎ Reference Manual “USB Devices”G :Wireless LAN Antenna<Only for model with wireless LAN>Î Reference Manual “Wireless LAN”H :Touch PadÎ Reference Manual “Using the Touch Pad”I : Bluetooth Antenna<Only for model with Bluetooth>Î Reference Manual “Bluetooth”J : Microphone Jack• When recording in stereo using a stereo microphone:Click (Start) - [Control Panel] - [Hardware and Sound] - [Sound]- [Recording] - [Microphone] - [Properties], and then remove a check mark of [Enable audio enhancements] in [Advanced].• When using a monaural microphone with a 2-terminal plug:Click (Start) - [Control Panel] - [Hardware and Sound] - [Sound] - [Recording] - [Microphone] - [Properties], and then add a check mark for [Enable audio enhancements] in [Advanced].K :Headphone JackYou can connect headphones or amplified speakers.When they are connected, audio from the internal speakers is not heard.L : Battery PackÎpage 13M :RAM Module SlotÎ Reference Manual “Expanding Memory”N :Î Emergency HoleÎ Reference Manual “CD/DVD Drive” O :Battery LatchesÎpage 13NLMOSIM Card Slot Wireless WAN Antenna<Only for model with wireless WAN>SIM Card BottomSIM card slot is located in the battery compartment on the bottom of the computer. Remove the battery pack to insert the SIM card. Insert the SIM card into the SIM Card Slot with the contact side facing upward and with the cut corner oriented as shown in the illustration.Do not insert the SIM card upside down.

13Getting StartedUseful InformationTroubleshootingAppendixFirst-time OperationPreparationACheck and identify the supplied accessories.If you do not find the described accessories, contact your technical support office.BRead the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging(Îpage 25).Slide the battery pack in parallel with the arrow direction and attach it so that the left and right dents (A) on the new battery pack match the projections (B) of the computer. In case that the dents does not match the projections of the computer, detach the battery pack once, then slide it while pushing it lightly to avoid floating.zTo remov e Slide both the left and right latches to the unlocked position, and push out the battery pack in parallel with the computer.CAUTIONzMake sure the battery latches are securely locked. Otherwise the battery pack may fall when you carry the computer.zDo not touch the terminals of the battery pack and the computer. Doing so can make the terminals dirty or damaged, and may cause malfunction of the battery pack and the computer.Hold the side of the computer with either of your hands and then hold and lift the (A) part to open the display.CAUTIONzDo not open the display wider than necessary (140° or more), and do not apply excessive pressure to the LCD. Do not open or close the computer holding the edge of the LCD segment.• AC Adaptor . . . . 1Model No: CF-AA6373A• AC Cord . . . . . . .1 • Battery Pack. . . 1Model No: CF-VZSU61U• Operating Instructions (This book) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• Product Recovery DVD-ROM Windows® 7 Professional (32-bit)*1 . . . . . . 1• Product Recovery DVD-ROM Windows® 7 Professional (64-bit)*1 . . . . . . 1*1 “This disc contains 32-bit software” or similar is printed on the label.1 Insert the battery pack.1 AAB2 Open the display.2A

14First-time OperationGetting StartedUseful InformationTroubleshootingAppendixThe battery charging starts automatically.CAUTIONzDo not disconnect the AC adaptor and do not switch the wireless switch to on until the first-time operation procedure is completed.zWhen using the computer for the first time, do not connect any peripheral device except the battery pack and AC adaptor.zHandling the AC adaptor• Problems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect your computer, an uninterrupt-ible power source (UPS) is highly recommended unless running from the bat-tery pack alone.Slide and hold the power switch for approximately one second until the power indicator lights.CAUTIONzDo not slide the power switch repeatedly.zThe computer will forcibly be turned off if you slide and hold the power switch for four seconds or longer.zOnce you turn off the computer, wait for ten seconds or more before you turn on the computer again.zDo not perform the following operation until the hard disk CD/DVD drive indicator turns off.• Connecting or disconnecting the AC adaptor• Sliding the power switch or CD/DVD drive power/open switch• Touching the keyboard or touch pad• Closing the displayzDo not change the Setup Utility until completing step 5. If you do so, Windows setup may not operate properly.Follow the on-screen instructions.zThe computer restarts several times. Do not touch the keyboard or touch pad, and wait until the hard disk CD/DVD drive indicator has turned off.zAfter the computer is turned on, the screen remains black or unchanged for a while, but this is not a malfunction. Wait for a moment until the Windows setup screen appears.zDuring setup of Windows, use the touch pad and clicking to move the cursor and to click an item.zSetup of Windows will take approximately 20 minutes.Go to the next step, confirming each message on the display.z“Join a wireless network” screen may not appear.You can set the Wireless Network after the setup of Windows is complete.CAUTIONzDo not turn off the computer until completing the first-time operation procedure.zDo not use the following words for user name: CON, PRN, AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9, @. In particular, if you create a user name (account name) that includes the “@” mark, a password will be requested at the log-on screen, even if no password has been set. If you try to log on without en-tering a password, “The user name or password is incorrect.” may be dis-played and you will not be able to log on to Windows (Îpage 23).zYou can change the user name, password, image and security setting after setup of Windows.zRemember your password. If you forget the password, you cannot use the Win-dows. Creating a password reset disk beforehand is recommended.Î Reference Manual “CD/DVD Drive”3 Connect your computer to a power outlet.4 Turn on the computer.5 Setup Windows.6 Change the internal CD/DVD drive letter if necessary.34

16Getting StartedUseful InformationTroubleshootingAppendixOn-screen ManualYou can access the following manuals on the computer screen after completing the “First-time Operation”.When you access the on-screen manual for the first time, the License Agreement of the Adobe Reader may be dis-played. Read it carefully and select [Accept] to proceed.Reference Manual The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.To access the Reference Manual:Double-click on the desktop.Alternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Reference Manual].Important Tips The Important Tips will provide you with the helpful information about the battery. Read to use the battery pack in the optimum condition to obtain longer operation time.To access the Important Tips:Double-click on the desktop.zAlternatively click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Important Tips].Hard Disk Handling The Hard Disk Handling will provide you with the helpful information on how to use the hard disk.To access the Hard Disk Handling:Click (Start) - [All Programs] - [Panasonic] - [On-Line Manuals] - [Hard Disk Handling].NOTEzWhen Adobe Reader update notice is displayed, we recommend you follow the on-screen procedure to update.See http://www.adobe.com/ for the latest version of Adobe Reader.

17Getting StartedUseful InformationTroubleshootingAppendixHandling and MaintenancezPlace the computer on a flat stable surface. Do not place the computer upright. If the computer is exposed to an extremely strong impact, it may become inoperable.zTemperature: Operation: 5 °C to 35 °C {41 °F to 95 °F}Storage: -20 °C to 60 °C {- 4 °F to 140 °F}Humidity: Operation: 30% to 80% RH (No condensation)Storage: 30% to 90% RH (No condensation)Even within the above temperature/humidity ranges, using for a long time in an extreme environment will result in the product deterioration and will shorten the product life.• Be sure to use the computer in an environment with sufficient heat ventilation.- Avoid using the computer on a highly heat retentive surfaces (e.g., rubber pads and blankets). If possible, use the computer on surfaces that can dissipate heat, such as a steel desk.- Do not cover the computer with towels, keyboard covers, etc., as this prevents heat dissipation.- When using the computer, always keep the display open. (Note, however, that closing the display while the com-puter is in use does not cause generation of heat, ignition, or other malfunctions.)zDo not place the computer in the following areas, otherwise the computer may be damaged.• Near electronic equipment. Image distortion or noise may occur.• Near magnets or in magnetic fields.• In extremely high or low temperature.zAs the computer can become hot during operation, keep it away from items that are sensitive to heat.This computer is designed to minimize shock to parts such as the hard disk drive, but no warranty is provided against any trouble caused by shock. Be extremely careful when handling the computer.zWhen carrying the computer:• Turn off the computer.• Remove all external devices, cables, cards and other protruding things.• Remove a disc in the CD/DVD drive.• Do not drop or hit the computer against solid objects.• Do not leave the display open.• Do not pick up or hold the computer by the display part.• Do not put anything (e.g., a piece of paper) between the display and keyboard.zWhen flying on an airplane:• Carry the computer with you, and never put it in checked baggage.• Obey the airline's instructions when using the computer on the air-plane.zWhen carrying a spare battery, put it in a plastic bag to protect its ter-minals.zThis computer contains a magnet and magnetic products at the locations circled in the illus-tration at right. Avoid leaving metallic object or magnetic media in contact with these areas.zThe touch pad is designed to be used with a finger tip. Do not place any object on its sur-face and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens).zAvoid any harmful substances such as oil from getting into the touch pad. The cursor may not work correctly.zIf the computer is being carried in a soft bag with the battery pack removed, avoid undue pressure on the body of the computer in a crowded place, etc., as this may result in damage to the LCD.When the battery indicator does not light onThe AC adaptor’s protection function may be working when the battery indicator does not light on even if the AC adap-tor and the battery pack are correctly connected with the computer.zPull out the AC cord and wait for more than 1 minute to reconnect the AC cord.zIf the problem persists, contact your technical support office.If the computer becomes warm during usagezCheck the following• If you are not using a wireless LAN, turn the wireless LAN off.• Use recommended RAM module products. Non-recommended RAM modules may not operate properly, and may cause damage to your computer. Operation EnvironmentHandling CautionsNG NGOK

18Handling and MaintenanceGetting StartedUseful InformationTroubleshootingAppendixzClick on the notification area and click . Then select [Panasonic Power management (Better Heat Dispersion)]• When changing to [Panasonic Power management (Better Heat Dispersion)], the following settings will change.- Change to [High Speed] from [Standard] in [Fan control mode].Rotation of the cooling fan will become faster and the computer can be cooled down. Note that the battery oper-ating time will be shorter.- Switch the screen saver to [Prohibited].- Other setting changes such as the lowering of the internal LCD brightness and disabling of Windows Aero will take place.• When you do not frequently use CPU or the rotation noise of the fan bothers you, set [Standard] or [Low Speed] in [Fan control mode].AClick on the notification area and click .BSelect [Standard] or [Low Speed] in [Fan control mode].Î Reference Manual “Customizing the Power Setting”When using peripheral devicesFollow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction manuals of the peripheral devices.zUse the peripheral devices conforming to the computer’s specifications.zConnect to the connectors in the correct direction.zIf it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc.zIf screws are included, fasten them securely.zRemove the cables when you carry the computer. Do not pull the cables forcibly.Preventing your computer from unauthorized use via wireless LAN/wireless WAN/Bluetooth<Only for model with wireless LAN/wireless WAN/Bluetooth>zBefore using wireless LAN/wireless WAN/Bluetooth, make the appropriate security settings such as data encryption.To clean the LCD panel and touch padWipe lightly with a gauze or other dry, soft cloth.To clean areas other than the LCD panel and touch padWet a soft cloth with water or a diluted kitchen cleanser (neutral), wring the cloth out thoroughly, and wipe the dirty area gently. Using a detergent other than a neutral kitchen cleanser (e.g., a weak alkali cleanser) may adversely affect painted surfaces.CAUTIONzDo not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc. Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to the surface.zDo not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause malfunction or damage.When setting the screen resolution to a resolution below the LCD’s resolution, the images appearing on the screen will be stretched. As a result, the characters displayed may appear blurred. This is normal, and not indicative of a malfunc-tion.To display large characters with no blurringTry the following steps while keeping the LCD in its resolution.zClick (Start) - [Control Panel] - [Appearance and Personalization] - [Display], select except for [Smaller - 100%] and then click [Apply].(This function will be enabled after log off the computer.)zTo display enlarged font sizes in applications such as Internet Explorer:Use the display enlargement function provided by the specific software application.zTo display enlarged desktop icons, title bar and cursor or magnify the specific part of the screen:Use “Icon Enlarger” or “Loupe Utility”.MaintenanceWhen Using the Computer with a Reduced Screen Resolution

19Getting StartedUseful InformationTroubleshootingAppendixThe keyboard on this computer incorporate a drain system (a moisture protection mechanism) that minimizes the amount of liquid reaching the inside of the computer even if water is spilled on the keyboard.Any water that comes in contact with the keyboard is drained off through holes in the bottom of the computer, so that vir-tually no water is left inside the computer. However, this is not a guarantee against damage to the hard disk or other internal parts, or against the loss or deletion of data.The drain system is incorporated into only the keyboard. It does not apply to any other components.zIf you spill water or any other liquid on the keyboard, even a small amount, be sure to perform the following steps. Failure to perform these steps may result in damage to the computer. The drain system will not provide complete protection against water entering the computer.1 Immediately turn off the computer, and remove the AC adaptor. 2 Wipe any water droplets off of the top of the keyboard using a soft, dry cloth. 3 Slowly lift up the computer, keeping it level, and wipe any water coming out of the holes on the bottom using a soft, dry cloth.If the computer is tilted during this step, liquid may seep inside the computer resulting in damage.4 Keeping the computer level, move the computer to a dry place. If the computer is placed back on the wet surface, water may seep inside the computer from the bottom.5 Insert the tip of a ball-point pen or other object into the emer-gency hole on the bottom of the computer, and move it in the direction of the arrow to open the disc cover. The computer should be kept level, without tilting, while the disc cover is being opened. Move the computer to the edge of the desk or table to perform this oper-ation. 6 Check to see whether there is any water inside the CD/DVD drive. If there is water inside, wipe it using a soft, dry cloth.7 Remove the battery pack.8 Be sure to contact your technical support office to have the computer checked for any malfunctions.If You Spill Water on the KeyboardNote that repairs resulting from liquids being spilled on the computer are not free of charge, and not covered by war-ranty.NGNG

20Getting StartedUseful InformationTroubleshootingAppendixReinstalling SoftwareCAUTIONDo not delete the partition with boot files on the hard disk.The disk space in the partition is not available to store data.PreparationzPrepare the Product Recovery DVD-ROM (included).zRemove all peripherals.zConnect the AC adaptor and do not remove it until installation is complete.NOTEzEven if reinstallation is performed, the number of times of DVD’s region code setting will not be reset.1 Turn on the computer, and press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.zIf the password is requested, enter the Supervisor Password.2 Write down all of the contents of the Setup Utility and press F9.At the confirmation message, select [Yes] and press Enter.3 Select the [Main] menu, then select [Optical Drive Power] and press Enter.4 Select [On] and press Enter.5 Press F10.At the confirmation message, select [Yes] and press Enter.The computer will restart.6 Press F2 or Del while [Panasonic] boot screen is displayed.The Setup Utility starts up.zIf the password is requested, enter the Supervisor Password.7 Set the Product Recovery DVD-ROM for Windows which you install into the CD/DVD drive.8 Select the [Exit] menu, then select [MATSHITA XXXXX] in [Boot Override].9 Press Enter.The computer will restart.10 Click [Reinstall Windows] and click [Next].The License Agreement screen appears.11 Click [Yes, I agree to the provisions above and wish to continue!] and click [Next].12 Select the settings and click [Next].z[Reinstall Windows to the whole Hard Disk to factory default.].You will have two partitions.z[Reinstall to the first 2 partitions.]*1.Select this option when the hard disk has already been divided into several partitions. For how to create a new partition, refer to “To change the partition structure” (Îpage 15).You can keep the partition structure.*1 This does not appear if Windows cannot be reinstalled to the partition containing boot files and the area usable by Windows.13 At the confirmation message, click [YES].Reinstallation starts automatically. (It will take approximately 25 - 35 minutes.)zDo not interrupt reinstallation, for example by turning off the computer. Otherwise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.14 Remove the Product Recovery DVD-ROM, and then click [OK] to turn off the computer.Reinstalling software will return the computer to the default condition. When you reinstall the software, the hard disk data will be erased.Back up important data to other media or an external hard disk before reinstallation.Area usable by Windows Hard disk Partition with boot files

21Getting StartedUseful InformationTroubleshootingAppendix15 Turn on the computer.zIf the password is requested, enter the Supervisor Password.16 Perform the “First-time Operation” (Î page 14).17 Start the Setup Utility and change the settings as necessary.18 Perform Windows Update.Confirming kind of Operating SystemThe kind of the system can be confirmed, click (Start) - [Computer], and then click [System Properties].

22Getting StartedUseful InformationTroubleshootingAppendixTroubleshooting (Basic)Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact your technical support office. You can also check the computer’s status in the PC Information Viewer (Î Reference Manual “Check the Computer’s Usage Status”).Starting Up and Sleep and Hibernation ModeThe computer does not power on/The power indicator or bat-tery indicator is not lit.zConnect the AC adaptor.zInsert a fully charged battery.zRemove the battery pack and the AC adaptor, then connect them again. zWhen the CPU temperature is high, the computer may not start up to prevent overheating of the CPU. Wait until the computer cools down, and then turn the power on again. If the com-puter does not power on even after cooling down, contact your technical support office.zPull out the AC cord and wait for more than 1 minute to reconnect the AC cord.Windows does not start up. zRemove all peripheral devices (e.g. USB memory).zIf the power indicator is lit, slide the power switch for four seconds or longer to turn off, then turn on again.zUsing the following procedure, start up in Safe Mode, and check the error details.ATurn on the computer, and when the [Panasonic] boot screen disappears (after enter-ing the password*1 if one is set) hold down F8.BRelease your finger when [Windows Advanced Options Menu] is displayed, and with Ï or Ð, select [Safe Mode], then press Enter.Follow the on-screen instructions.*1 Supervisor Password or User Password set with the Setup UtilityzPress F9 in the Setup Utility to return the Setup Utility settings (excluding the pass-words) to the default values. Start the Setup Utility and make the settings again.After adding or changing the RAM module, the power is turned on but nothing is dis-played on the screen.zTurn off the computer and remove the RAM module, then confirm whether the RAM module has compliant to specification. When the RAM module has conformed to specifi-cation, install it again.Cannot boot from internal CD/DVD drive.zMake sure that the bootable CD/DVD is set properly.zStart the Setup Utility, and confirm the following settings.• [Optical Drive] is set to [Enabled] in the [Advanced] menu.• [Optical Drive Power] is set to [On] in the [Main] menu.• [Boot Option #1] is set to [CD/DVD Drive] in the [Boot] menu.zWhen an external CD/DVD drive is connected, you cannot boot from the internal CD/DVD drive.You have forgotten the password.zSupervisor Password or User Password: Contact your technical support office.zAdministrator password: • If you have another account with Administrator authority, log-on with it, then delete the password for the problem account.• If you have a password reset disk, click [Reset password] displayed after the password input error, then follow the on-screen instructions to set a new password.• If you cannot do either of the above, you will need to reinstall (Îpage 20) and setup Windows.“Remove disks or other media. Press any key to restart” or a similar mes-sage appears.zA floppy disk is in the floppy disk drive and it does not contain system startup informa-tion. Remove the floppy disk and press any key.zThis message may appear with some devices connected to the USB port. Remove the device or set [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.zIf the problem persists after removing the disk, it may be a hard disk failure. Perform the rein-stallation and return the hard disk to its condition at the time of purchase. (Îpage 20) If the problem persists even after the reinstallation, contact your technical support office.[Executing Battery Recali-bration] screen appears.zThe Battery Recalibration was canceled before Windows was shut down last time. To start up Windows, turn off the computer by the power switch, and then turn on.The computer will not auto-matically enter sleep or hibernation.zIf you connect to a network using wireless LAN function, perform access point settings. (Î Reference Manual “Wireless LAN”)zIf you do not use wireless LAN function, turn off wireless LAN function. (Î Refer-ence Manual “Disabling/Enabling Wireless Communication”)zMake sure that you are not using any software that regularly accesses the hard disk.

23Getting StartedUseful InformationTroubleshootingAppendix[Enter Password] does not appear when resuming from sleep hibernation.zSelect [Enabled] in [Password On Resume] in the [Security] menu of the Setup Utility (Î Reference Manual “Setup Utility”).zThe Windows password can be used instead of the password set in the Setup Utility.AClick (Start) - [Control Panel] - [User Accounts and Family Safety] - [Add or remove user accounts] and select the account, and set the password.BClick (Start) - [Control Panel] - [System and Security] - [Power Options] - [Require a password on wakeup] and a check mark for [Require a password].When logging on (e.g., resuming the computer), audio is distorted.zPerform the following steps to change the audio settings to prevent audio output.ARight-click the desktop and click [Personalize] - [Sounds].BRemove the check mark from [Play Windows Startup sound], and click [OK].Cannot resume. zOne of the following operations may have been carried out.• In sleep mode, the AC adaptor or battery pack was disconnected, or a peripheral was connected or disconnected.• The power switch was slid for four seconds or longer to forcibly turn off the computer.Slide the power switch to turn on the computer. Data not saved will be lost.Other startup problems. zCheck to see if there was a disk error.ARemove all peripheral devices including an external display.BClick (Start) - [Computer] and right-click [Local Disk (C:)], and click [Properties].CClick [Tools] - [Check Now…].• A standard user needs to enter an administrator password.DSelect the option in [Check disk options] and click [Start].EClick [Schedule disk check] and restart the computer.zStart the computer in Safe Mode and check the error details. (Îpage 22 “Windows does not start up”.)Shutting DownWindows does not shut down.zRemove all peripheral devices.zWait one or two minutes. It is not a malfunction.PasswordEven after entering the pass-word, a message appears requesting to type it again.zIf lights up, press NumLk to disable the ten-key mode, and then input.zIf lights up, press Caps Lock to disable the Caps Lock mode, and then input.Cannot log on to Windows. (“The user name or password is incorrect.” is displayed.)zThe user name (account name) includes an “@” mark.If another user account exists:Log on to Windows using another user account, and delete the account that includes “@”. Then create a new account.If no other account exists:You need to reinstall Windows (Îpage 20).DisplayWhen the screen becomes black for a moment.zWhen you set [Intel(R) video driver power saving function] - [Intel(R) Display Power Sav-ing Technology] of Power Plan Extension Utility to [Enabled], if you do the following oper-ations, the screen becomes black for a moment, but this is not a malfunction. You can use it.• Adjust the brightness of the screen with Fn + F1 / Fn + F2.• Remove and insert the AC adaptor.While you are using motion video playback software, benchmark software for graphic, if error screen is displayed or application software does not function normally, set [Intel(R) video driver power saving function] - [Intel(R) Display Power Saving Technology] to [Disabled].No display. zThe external display is selected. Press Fn + F3 (or + P) to switch the display. Wait until the display has been switched completely before pressing Fn + F3 (or + P) again.zThe display is turned off by the power-saving function. To resume, do not press the direct selection keys, but press any other key like Ctrl.zThe computer entered sleep or hibernation by the power-saving function. To resume, slide the power switch.zThe screen may become darker. Press Fn + F2 to make the screen brighter.Starting Up and Sleep and Hibernation Mode

$24Troubleshooting (Basic)Getting StartedUseful InformationTroubleshootingAppendixThe screen is disordered. zChanging the number of display colors and resolution may affect the screen. Restart the computer.zThe refresh rate of the internal LCD may be 40 hertz. Change the refresh rate of the internal LCD.ARight-click on the desktop, and click [Graphics Properties].BClick [General Settings].CIf [Refresh Rate] of the Notebook is [40 Hz], change to [60 Hz] and click [OK].The external display does not work normally.zIf the external display does not support the power saving function, it may not work nor-mally when the computer enters the power saving mode. Turn off the external display.BatteryThe battery indicator is lights red.zThe battery level is very low (the charge is approx. 9% or less).zConnect the AC adaptor. You can use the computer when the indicator light is orange. If you do not have an AC adaptor, save your data and power off your computer. After replacing the battery pack with a fully charged one, turn your computer on again.The battery indicator is blinking.zIf blinking red:Quickly save your data and power off your computer. Remove the battery pack and dis-connect the AC adaptor, then connect them again. If the problem persists, contact your technical support office. The battery pack or charging circuit may be defective.zIf blinking orange:• Battery cannot be recharged temporarily because the internal temperature of the bat-tery pack is outside the acceptable temperature range for recharging. Your computer can be used normally in this state. Once the range requirement is satisfied, charging begins automatically.• Software applications and peripheral devices (USB devices, etc.) are consuming too much power. Exit the software applications currently running, and remove all peripher-als. Once the range requirement is satisfied, charging begins automatically.The battery indicator is flashing.zThe battery is recharging.If [Battery Charging Indicator] in [Main] menu of the Setup Utility is set to [Flashing], the indicator will alternately become lighter and darker.Touch PadThe cursor does not work. zWhen using the external mouse, connect it correctly.zRestart the computer by using the keyboard. Press and press Î two times, and press Ï to select [Restart] and press Enter.zIf the computer does not respond to keyboard commands, read “No response” (Îbelow).Cannot input using the touch pad.zSet [Touch Pad] to [Enabled] in the [Main] menu of the Setup Utility.zThe drivers for some mice may disable the touch pad. Check your mouse’s operating instructions.Reference ManualThe Reference Manual is not displayed.zInstall Adobe Reader. ALog on to Windows as an administrator.BClick (Start) and input “c:\util\reader\Setup.exe” in [Search programs and files] then press Enter.CUpdate Adobe Reader to its latest version.DIf your computer is connected to the internet, start up Adobe Reader and click [Help] - [Check for Updates…].OthersNo response. zPress Ctrl+Shift+Esc to open Task Manager and close the software application that is not responding.zAn input screen (e.g., password input screen at startup) may be hidden behind another window. Press Alt+Tab to check.zSlide the power switch for four seconds or longer to shut down the computer, and then slide the power switch to turn it on. If the application program does not work normally, uninstall and reinstall the program. To uninstall, click (Start) - [Control Panel] - [Programs] - [Uninstall a program].The computer does not rec-ognize the CD/DVD drive.zRestart the computer.After the computer restarts, it may recognize a CD/DVD drive.Display$

25Getting StartedUseful InformationTroubleshootingAppendixLIMITED USE LICENSE AGREEMENTTHE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC PRODUCT (“PRODUCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.Panasonic Corporation has developed or otherwise obtained the Programs and hereby licenses their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to achieve your intended results, and for the installation, use and results obtained therefrom.LICENSEA. Panasonic Corporation hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only a LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title, ownership nor any other rights in or to the Programs and related documentation nor in or to the algorithms, con-cepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership and rights shall remain with Panasonic Corporation or its suppliers.B. You may use the Programs only on the single Product which was accompanied by the Programs.C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not distrib-ute or otherwise make the Programs or related documentation available to any third party, by time-sharing or other-wise, without the prior written consent of Panasonic Corporation.D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or attempt to modify, the Programs.E. You may transfer the Programs and license them to another party only in connection with your transfer of the single Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation, to the same party or destroy any such copies not so transferred.F. You may not remove any copyright, trademark or other notice or product identification from the Programs and you must reproduce and include any such notice or product identification on any copy of any Program.YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PER-MITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.TERMThis license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate this license at any time by destroying, at your expense, the Programs and related documentation together with all cop-ies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any such termination, you agree to destroy, at your expense, the Programs and related documentation together with all cop-ies thereof in any form.YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-TER OF THIS AGREEMENT.GOVERNMENT RESTRICTED RIGHTS.The Software is provided with “RESTRICTED RIGHTS.” Use duplication or disclosure by the government is subject to restrictions as set forth in FAR52.227-14 and DFAR252. 227-7013 et seq. or their successors.Use of the Software by the government constitutes acknowledgement of Intel’s proprietary rights therein.Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95052.

26Getting StartedUseful InformationTroubleshootingAppendixContrat de licence d’usage limitéLe(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic (le “Produit”) sont exclusivement concédés en licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cidessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et conditions des présentes.Panasonic Corporation a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour obtenir les résultats escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus.LicenceA. Panasonic Corporation vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs d’utiliser les Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez ne recevoir qu’un droit limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n’obtenir aucun droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni vis-à-vis des algorithmes, concepts, dessins, configurations et idées représentés par ou incorporés dans les Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à Panasonic Corporation ou à leurs propriétaires.B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.C. Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous ne pouvez ni distribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage de temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de Panasonic Corporation.D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documentation les accompagnant pour quelque fin que ce soit, à l’exception d’une (1) copie des Logiciels à des fins de sauvegarde uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné par les Logiciels. Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport avec votre cession du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni aucune identification de produit des Logiciels et vous devez reproduire et inclure toutes ces notices ou identifications de produit sur toutes les copies des Logiciels.Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs copies, de façon électronique ou mécanique, en tout ou en partie.Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie, à l’exception de ce qui est expressément stipulé dans ce contrat.Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé au paragraphe E ci-dessus, votre licence est automatiquement résiliée.Termes, clauses et conditionsCette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation antérieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée, avec application immédiate, si les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme que ce soit.Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes, clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre communication entre nous, relativement à l’objet du présent contrat.

27Getting StartedUseful InformationTroubleshootingAppendixSpecificationsTo check CPU speed, memory size and the hard disk drive (HDD) size:Start the Setup Utility (Î Reference Manual “Setup Utility”) and select [Information] menu.[Processor Speed]: CPU speed, [Memory Size]: Memory size, [Hard Disk]: Hard disk drive sizeMain Specifications Model No. CF-S9KWAZZDM CF-S9KWNZZDMCPU Intel® vPro™ Technology *1Intel® Core™ i5-520M vPro™ processor (2.40 GHz with Turbo Boost up to 2.93 GHz, Intel® Smart Cache 3 MB*2)Chip Set Mobile Intel® QM57 Express ChipsetMain Memory*2*3 2 GB, DDR3 SDRAM (6 GB Max.) Video Memory*2*4UMA 763 MB Max. (When Memory is 2 GB) / UMA 1563 MB Max. (When Memory is 4or6GB)Video Controller Intel® HD Graphics (Built-in CPU)Hard Disk Drive*5 320 GBApprox. 300 MB is used as a partition with recovery tools. (Users cannot use this partition.)CD/DVD Drive DVD MULTI Drive built-in, Buffer underrun error prevention function: SupportedContinuous Data Trans-fer Speed*6*7 Reading*8 zDVD-RAM*10: 5X (Max.)(4.7 GB)*5 zDVD-R*11: 8X (Max.) zDVD-RW: 8X (Max.) zDVD-R DL: 8X (Max.) zDVD-ROM: 8X (Max.) zCD-ROM: 24X (Max.) zCD-R: 24X (Max.) zCD-RW: 24X (Max.) z+R: 8X (Max.) z+R DL: 8X (Max.) z+RW: 8X (Max.) zHigh Speed +RW: 8X(Max.) zHigh-Speed CD-RW: 24X(Max.) zUltra-Speed CD-RW: 24X(Max.)Writing*9 zDVD-RAM*10: 2X/3X/3-5X (4.7 GB)*5 zDVD-R: 2X/3.3-4X/3.3-6X/3.3-8X zDVD-RW: 1X/2X/2-4X/2-6X z+R: 2.4X/3.3-4X/3.3-6X/3.3-8X z+RW: 2.4X/2.4-4X zHigh Speed +RW: 3.3X/3.3-6X zCD-R: 8X/8-12X/8-16X/10.8-24X zCD-RW: 4X zHigh-Speed CD-RW: 4X/8X/10XSupported Discs/For-mat*7 Reading zDVD-ROM (Single Layer, Dual Layer) zDVD-Video zDVD-R*11 (1.4 GB, 2.8 GB, 4.7 GB)*5 zDVD-RW (Ver.1.1/1.2 1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 zDVD-R DL (8.5 GB)*5 zDVD-RAM*10 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 z+R (4.7 GB)*5 z+R DL (8.5 GB)*5 z+RW (4.7 GB)*5 zCD-Audio zCD-ROM (XA compatible) zCD-R zPhoto CD (multiple session compatible) zVideo CD zCD EXTRA zCD-RW zCD-TEXT zHigh Speed +RW (4.7 GB)*5 zHigh-Speed CD-RW zUltra-Speed CD-RWWriting zDVD-RAM*10 (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 zDVD-R (1.4 GB, 2.8 GB, 4.7 GB for General)*5 zDVD-RW (Ver.1.1/1.2 1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB)*5 z+R (4.7 GB)*5 z+RW (4.7 GB)*5 zCD-R zCD-RW zHigh Speed +RW (4.7 GB)*5 zHigh-Speed CD-RWDisplay Method 12.1 WXGA type (TFT) (1280 × 800 dots)Internal LCD 65,536/16,777,216 colors (1280 × 800 dots)*12External Display*13 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 720 dots/1280 × 768 dots/1280 × 1024 dots/1400 × 1050 dots/1680 × 1050 dots/1600 × 1200 dots/1920 × 1080 dots/1920 × 1200 dots)Simultaneous Display on LCD + Exter-nal Display*13 65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 720 dots/1280 × 768 dots/1280 x 800 dots)*12Wireless LAN Intel® Centrino® Advanced-N 6200*14 (Îpage 28)Bluetooth*15 Îpage 28LAN*16 IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-TModem*17 Data: 56 kbps (V.92) FAX: 14.4 kbpsFingerprint Reader*18 -Array Size: 192 × 4 pixels, Image Size: 192 × 512 pixels, Image Resolution: 508 DPISound WAVE and MIDI playback, Intel® High Definition Audio subsystem support, Stereo Speakers (built in)Security Chip TPM (TCG V1.2 compliant)*19Card Slots PC Card Slot × 1, Type I or Type II, Allowable current 3.3 V: 400 mA, 5 V: 400 mASD Memory Card Slot*20 × 1RAM Module Slot × 1, DDR3 SDRAM, 204-pin, 1.5 V, SO-DIMM, PC3-6400 Compliant

$29Getting StartedUseful InformationTroubleshootingAppendix*1 The Intel® Active Management Technology (Intel® AMT) function must be set before use.*2 1 MB = 1,048,576 bytes / 1 GB = 1,073,741,824 bytes*3 You can physically expand the memory up to 4 GB, but the total amount of usable memory available will be less depend-ing on the actual system configuration.*4 A segment of the main memory is allotted automatically depending on the computer’s operating status. The size of the Video Memory cannot be set by the user.The size of Video memory is allotted depending on the oper-ating system.For Windows 7 (64-bit), UMA 1696 MB Max. (When Memory is 4 or 6 GB)*5 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.*6 Data transfer speeds indicate values measured by Panasonic Corporation. The data transfer rate of DVD per 1X speed is 1,350 KB/s. The data transfer rate of CD per 1X speed is 150 KB/s.*7 Performance of CD-R, CD-RW, DVD-RAM, DVD-R, DVD-R DL, DVD-RW, +R, +R DL, and +RW cannot be guaranteed depending on writing status and recording format. Also, some data cannot be played back depending on the disc, settings, and environment being used.Does not support writing to DVD-R DL/+R DL (dual layer discs) and Ultra-Speed CD-RW. Does not support 2.6 GB DVD-RAM.*8If an unbalanced disc (e.g., a disc with which the balance has been displaced from the center) is inserted, the speed may become slower if there are large vibrations while the disc is rotating.*9Depending on the disc, the writing speed may become slower.*10Only non-cartridge type or removable cartridge type can be used. *11 DVD-R is compatible with 4.7 GB (for General) playback. DVD-R (for Authoring) playback is compatible with discs recorded using Disc-at-Once recording.*12 A 16,777,216 color display is achieved by using the dithering function. *13 Display may be impossible using some connected external displays.*14 Only for model with wireless LAN.*15 Only for model with Bluetooth.*16 Some devices cannot be used depending on the port type.*17 Only for model with modem.*18 Only for model with Fingerprint Reader.*19Only for model that supports TPM. For information on TPM, click (Start) and input “c:\util\drivers\tpm\README.pdf” in [Search programs and files] and press Enter, and refer to the Installation Manual of “Trusted Platform Module (TPM)”.*20 This slot is not compatible with the UHS-I high speed trans-fer. Operation has been tested and confirmed using Pana-sonic SD Memory Card with a capacity of up to 2 GB, Panasonic SDHC Memory Card with a capacity of up to 32 GB, and Panasonic SDXC Memory Card with a capacity of up to 64 GB. Operation on other SD equipment is not guaranteed.*21Does not guarantee operation of all USB-compatible peripherals.*22Does not guarantee operation of all HDMI-compatible peripherals.*23Use a condenser-stereo microphone.*24 <Only for North America>The AC adaptor is compatible with power sources up to240 V AC adaptor. This computer is supplied with a 125 V AC compatible AC cord.20-M-1-1*25Measured using MobileMark™ 2007 (LCD brightness : 60 cd/m2).Varies depending on the usage conditions, or when an optional device is attached. When Economy Mode (ECO) is enabled, the operating time becomes approximately 20% shorter than when it is disabled.*26 When Economy Mode (ECO) is enabled, the charging time becomes approx. 5.0 hours (Power on/off). Varies depending on the usage conditions, CPU speed, etc.It may take a long time to charge a fully discharged battery.*27 Approx. 0.7 W when the battery pack is fully charged (or not being charged) and the computer is off.<When using with 115 V AC>Even when the AC adaptor is not connected to the computer, power is consumed (Max. 0.3 W) simply by having the AC adaptor plugged into an AC outlet.*28 Rated power consumption.23-E-1*29 41.4 mm at thickest point (excluding protrusions).*30 Average value. May differ depending on models.*31 Operations of this computer are not guaranteed except for the pre-installed OS and the installed OS by using the Prod-uct Recovery DVD-ROM (included). Some parts of the software in the Product Recovery DVD-ROM may not be installed depending on a model.*32 Must be installed before use.*33 The graphics accelerator of this computer supports up to DirectX 10.*34 The Product Recovery DVD-ROM is required.*35 These are speeds specified in IEEE802.11a+b+g+n stan-dards. Actual speeds may differ.$

Panasonic of North America 9TGCF-S91 Toughbook PC with WWAN, WLAN and Bluetooth User Manual Operating Instructions

Panasonic Corporation of North America Toughbook PC with WWAN, WLAN and Bluetooth Operating Instructions

Users Manual

Navigation menu

Namespaces

Views

Navigation