Panasonic of North America 9TGWL11A Intel Centrino Advanced-N 6205 User Manual WL11A
Panasonic Corporation of North America Intel Centrino Advanced-N 6205 WL11A
Contents
Operating Instructions 3
Model: WL11A
Operating Instructions
1 GENERAL
The purpose of this manual is to explain correct way how to integrate module
WL11A to Panasonic PC. It includes procedures that shall assist you to avoid
unforeseen problems. This manual presents information that shows how module
complies with regulations in certain regions.
The system may only be implemented in the configuration that was authorized.
Note that any changes or modifications to this equipment not expressly
approved by Panasonic could void the user’s authority to operate this
equipment.
2. Frequency Scanning Plan
The EEPROM will be programmed at the factory to only operate and actively
scan on these specific channels:
Channels 1-11, 2412-2462MHz 802.11b mode
Channels 1-11, 2412-2462MHz 802.11g mode
Channels 1-11, 2412-2462MHz 802.11n mode (20MHz channel)
Channels 3-9, 2422-2452MHz 802.11n mode (40MHz channel)
The following channels will be programmed at the factory to passively scan and
will only listen and cannot send a probe request to initiate communication on
these specific channels. Ad-hoc mode is always disabled on these passive
channels.
Channels 36-48, 5180-5240MHz 802.11a mode
Channels 36-48, 5180-5240MHz 802.11n mode (20 MHz channel)
Channels 38-46, 5190-5230MHz 802.11n mode (40MHz channel)
Channels 52-64, 5260-5320MHz 802.11a mode
Channels 52-64, 5260-5320MHz 802.11n mode (20 MHz channel)
Channels 54-62, 5270-5310MHz 802.11n mode (40MHz channel)
Channels 100-140, 5500-5700MHz 802.11a mode
Channels 100-140, 5500-5700MHz 802.11n mode (20 MHz channel)
Channels 102-134, 5510-5670MHz 802.11n mode (40MHz channel)
Channels 149-165, 5745-5825MHz 802.11a mode
Channels 149-165, 5745-5825MHz 802.11n mode (20 MHz channel)
Channels 151-159, 5755-5795MHz 802.11n mode (40MHz channel)
This information when programmed into the EEPROM will not be accessible and
can not be changed by the end user.
Regulatory Information
USA-Federal Communications Commission (FCC)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz
frequency range. FCC requires this product to be used indoors for frequency
range 5.15 to 5.25 GHz to reduce the potential for harmful interference to
co-channel Mobile Satellite systems. High power radars are allocated as primary
users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations
can cause interference with and/or damage this device.
Labeling
The model WL11A is labelled as below.
FCC ID: ACJ9TGWL11A
The proposed with FCC ID label format is to be placed on the module. If FCC ID
is not visible when the module is installed into the system, “Contains FCC ID:
ACJ9TGWL11A” shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with FCC RF exposure compliance requirements, the antenna(s)
used for this transmitter must not be collocated or operating in conjunction with
any other antenna or transmitter within a host device, except in accordance with
FCC multi-transmitter product procedures.
Canada-Industry Canada (IC)
This device complies with RSS 210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may
cause undesired operation of this device.
L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
Caution
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (EIRP)
is not more than that required for successful communication.
When using IEEE 802.11a wireless LAN, this device is restricted to indoor use
due to its operation in the 5.15- to 5.25-GHz frequency range. Industry Canada
requires this product to be used indoors for the frequency range of 5.15 GHz to
5.25 GHz to reduce the potential for harmful interference to co-channel mobile
satellite systems. High power radar is allocated as the primary user of the 5.25-
to 5.35-GHz and 5.65 to 5.85-GHz bands. These radar stations can cause
interference with and/or damage to this device.
Afin de réduire le risqué d’interférence radioélectrique aux autres utilisateurs
des bandes de frequencies, le type d’antenne et son gain doivent être tells que
la puissance isotrope rayonnée équivalente (PIRE) n’est pas plus élevée que le
niveau requis pour assurer la communication.
Cet appareil (pour réseaux locaux radioélectriques) dans les bandes de
frequencies 5150-5250.MHz est réervéàune utilisa-tion àl’intéieur afin de réuire
le risqué d’interféence avec les systèmes satellites mobiles bicanaux. Les radars
forte puissance sont désignés comme étant les pre-miers utilisateurs (c’st-à-dire
qu’ls ont la priorité) des bandes de frequencies 5250-5350 MHz et 5650-5850
MHz. Ces stations ra-dars peuvent provoquer des interferences et/ou des
dommages à ce périphérique
Labeling
The model WL11A is labelled as below.
IC: 216A-CFWL11A
The proposed with FCC ID label format is to be placed on the module. If IC ID is
not visible when the module is installed into the system, “Contains IC:
216A-CFWL11A” shall be placed on the outside of final host system.
Caution: Exposure to Radio Frequency Radiation.
To comply with IC RF exposure compliance requirements, the antenna(s) used
for this transmitter must not be collocated or operating in conjunction with any
other antenna or transmitter within a host device, except in accordance with IC
multi-transmitter product procedures.