Panasonic of North America SC-HTB8 BT Module User Manual SPEC BM830 V0 2 20130803
Panasonic Corporation of North America BT Module SPEC BM830 V0 2 20130803
UserManual.wiki
>
Panasonic of North America
>
SC HTB8 User Manual
User Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Product Specification Spec-BM830-V0.2 Page 3 of 10 www.sunitec-cn.com ® Pin Configurations PIN NO. NAME TYPE FUNCTION RE-MARK1 GND GND Ground 2 AIO0 Bi-directional Analogue programmable input / output line 3 PIO14 Bi-directional Programmable input / output line 14. Alternative function: ■ UART_RX: UART data input 4 PIO15 Bi-directional Programmable input / output line 15. Alternative function: ■ UART_TX: UART data output 5 PIO16 Bi-directional Programmable input / output line 16. Alternative function: ■ UART_RTS: UART request to send, active low 6 PIO17 Bi-directional Programmable input / output line 17. Alternative function: ■ UART_CTS: UART clear to send, active low 7 PIO10 Bi-directional Programmable input / output line 10. Alternative function: ■ QSPI_FLASH_CLK: SPI flash clock ■ I2C_SCL: I²C serial clock line 8 SCL Bi-directional Internal EEPROM SCL 9 PIO11 Bi-directional Programmable input / output line 11. Alternative function: ■ QSPI_IO[0]: SPI flash data bit 0 ■ I2C_SDA: I²C serial data line 10 PIO12 Bi-directional Programmable input / output line 12. Alternative function: ■ QSPI_FLASH_CS#: SPI flash chip select ■ I2C_WP: I²C bus memory write protect line 11 PIO13 Bi-directional Programmable input / output line 13. Alternative function: ■ QSPI_IO[1]: SPI flash data bit 1 12 SPI_PCM# Bidirectional with weak pull-down SPI/PCM select input: ■0 = PCM/PIO interface ■1 = SPI 13 GND GND Ground 14 PIO3 Bi-directional Programmable input / output line 3. Alternative function: ■ SPI_MISO: SPI data output ■ PCM1_OUT: PCM1 synchronous data output 15 PIO2 Bi-directional Programmable input / output line 2. Alternative function: ■ SPI_MOSI: SPI data input ■ PCM1_IN: PCM1 synchronous data input 16 PIO5 Bi-directional Programmable input / output line 5. Alternative function: ■ SPI_CLK: SPI clock ■ PCM1_CLK: PCM1 synchronous data clock 17 PIO4 Bi-directional Programmable input / output line 4. Alternative function: ■ SPI_CS#: chip select for SPI, active low ■ PCM1_SYNC: PCM1 synchronous data sync 18 GND GND Ground 19 GND GND Ground 20 RST# Input with strong pull-up Reset if low. Pull low for minimum 5ms to cause a reset. 21 GND GND Ground 22 LED1 Bi-directional LED driver. Alternative function: programmable output PIO[30]. 23 LED0 Bi-directional LED driver. Alternative function: programmable output PIO[29]. 24 VREGENABLE CMOS Input Regulator enable input Can also be sensed as an input. Regulator enable and multifunction button. A high](https://usermanual.wiki/Panasonic-of-North-America/SC-HTB8/User-Guide-2239399-Page-3.png)
![Product Specification Spec-BM830-V0.2 Page 4 of 10 www.sunitec-cn.com ® input (tolerant to VBAT) enables the on-chip regulators, which can then be latched on internally and the button used as a multifunction input 25 GND GND Ground 26 VBUS Power Input Charger input. Typically connected to VBUS (USB supply) as Section 12 shows. 27 CHG_EXT External battery charger control. External battery charger transistor base control when using external charger boost. Otherwise leave unconnected. 28 VBAT_SENSE Battery charger sense input. Connect directly to the battery positive pin. 29 VBAT Power IN Battery positive terminal. 30 GND GND Ground 31 1V8_OUT Power out Serial Peripheral Interface Clock 32 VDD_PADS Power IN Positive supply input for input/output ports 33 3V3_OUT Power out 3.3V bypass linear regulator output. 34 GND GND Ground 35 USB_N Bi-directional USB data minus 36 USB_P Bi-directional USB data plus with selectable internal 1.5kΩ pull-up resistor 37 GND GND Ground 38 PIO9 Bi-directional Programmable input / output line 9. Alternative function: ■ UART_CTS: UART clear to send,active low 39 PIO0 Bi-directional Programmable input / output line 0. Alternative function: ■ UART_RX: UART data input 40 PIO1 Bi-directional Programmable input / output line 1. Alternative function: ■ UART_TX: UART data output 41 PIO8 Bi-directional Programmable input / output line 8. Alternative function: ■ UART_RTS: UART request to send, active low 42 PIO7 Bi-directional Programmable Input/Output Line 43 PIO6 Bi-directional Programmable Input/Output Line 44 PIO21 Bi-directional Programmable Input/Output Line 45 PIO18 Bi-directional Programmable Input/Output Line 46 LED2 Bi-directional LED driver. Alternative function: programmable output PIO[31] 47 GND GND Ground 48 MIC_BIAS Analogue out Microphone bias 49 LINE_AN Analogue in Line input negative, channel A 50 LINE_AP Analogue in Line input positive, channel A 51 LINE_BN Analogue in Line input negative, channel B 52 LINE_BP Analogue in Line input positive, channel B 53 AGND Analogue Ground connection for audio and audio driver. 54 SPK_RN Analogue out Speaker output negative, right 55 SPK_RP Analogue out Speaker output positive, right 56 SPK_LN Analogue out Speaker output negative, left 57 SPK_LP Analogue out Speaker output positive, left 58 GND GND Ground 59 RF_IN GND Bluetooth 50Ω transmitter output /receiver input 60 GND GND Ground](https://usermanual.wiki/Panasonic-of-North-America/SC-HTB8/User-Guide-2239399-Page-4.png)
