Pantech HWT-2150 WLL Terminal ( CDMA ) User Manual CRN 9389 Q1 revised

Download:
Mirror Download [FCC.gov]
Document ID	397056
Application ID	RQtz/NDuamzfkGTayCHrJg==
Document Description	CRN 9389 Q1 revised user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	117.73kB (1471579 bits)
Date Submitted	2004-02-17 00:00:00
Date Available	2003-08-14 00:00:00
Creation Date	2003-08-09 11:51:22
Producing Software	Power Macintosh¿ë Acrobat PDFWriter 4.0
Document Lastmod	2004-02-16 23:29:23
Document Title	CRN 9389 Q1 revised user manual
Document Creator	QuarkXPress(MAC)
Document Author:	1

hWT-2150(8-9) 2003.8.9 11:51 AM 페이지1
Contents
Features of the Product ………………………………………………………………… 2
Before Using
Supplementary functions
Speed Dial …………………………………………………
Emergency call hold ………………………………………
Hot Line Service ……………………………………………
Alarm Reminder ……………………………………………
Lock …………………………………………………………
Ear-piece Volume Control …………………………………
Reset ………………………………………………………
Clip Setting …………………………………………………
Analog G3 Fax Standard Setting …………………………
Default Data Rate Setting …………………………………
Ringer Frequency & Candence Control …………………
Dial Tone Frequency Control ……………………………
Default Vocoder Selection ………………………………
Timed Hot Line Dial Send Waiting Time Control ………
Hook Flash Time (Click Time) Control …………………
Voice Privacy Settng ………………………………………
Serial Interface Setting (None For HWT-2150) …………
A Key Value Input …………………………………………
Network Dial Tone Setting ………………………………
System Parameter Input …………………………………
Precautions in using ……………………………………… 5
Components Check ………………………………………… 6
Function Description of Each Component ……………… 7
Installation
General installation…………………………………………… 9
Wall bracket Installation ……………………………………13
Installation for Data Service ………………………………15
Operation
Power on ………………………………………………………16
Power off ………………………………………………………16
Call Send ………………………………………………………17
Call Receive ……………………………………………………17
Analog G3 fax service ……………………………………… 18
Data service …………………………………………………18
Appendix
21
22
24
25
26
27
27
28
29
30
31
32
33
33
34
35
35
38
38
37
Summary Table ……………………………………………… 39
Technical Specification …………………………………… 41
Troubleshooting……………………………………………… 42
Safety
Safety Information ………………………………………… 43
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지3
HWT-2150 3
Features of the Product
User Guide
Features of the Product
First, clear voice quality
- 13Kbps & EVRC Vocoder
- Provides the same voice quality as that of the wired telephone service
Second, elegant design and simple installation
- Desktop & wall mounting structure provides simple installation
at any place
- Analog G3 Fax (Optional)
- Pay Phone Interface
(16KHz, 12KHz, Metering Pulse, Polarity Reversal)
Fifty, extended call / waiting time
- Adoption of up-to-date MSM5105 chip and super power-saving circuit
design provides extended battery lifetime at a lower power
consumption compared with other products.
Third, varieties of supplementary services
- System Dependent Feature : Caller ID, OTASP, Authentication,
Voice mail Notification, Voice Privacy
- Stand Alone Feature : Redial, Speed dialing(up to 99),
Emergency Call Hold, Hot Line, Alarm Reminder
- POTS (Plain Old Telephone Service), data, etc.
Fourth, varieties of interfaces
- Provides high speed digital data service at 64Kbps.
- Circuit Data Communicate (file send/receive)
- Support PC Fax (HotFax, WinFax)
- Medium Data Rate Packet Data Support
(Internet & FTP file send/receive)
Sixth, varieties of tone / ring generators through simple setup
- Simple setup of dial / warning tones (4 types) and call receiving alert
rings (18 types) according to user's needs.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지5
HWT-2150 5
User Guide
Before Using
B e f o re Using
Precautions in using
Do not disassemble
or revise the FWT terminal
at your discretion
This product is the Fixed Wireless Terminal (FWT) designed using
the up-to-date communication technology Code Division Multiple
Do not touch
the antenna during
calling
Access(CDMA) to fulfill superior communication services of users.
Please, review this manual closely before using the product.
Do not use the FWT terminal at hot
and humid places. It may not be repairable
if wet by rain or drinks
Caution : As the backup battery of the FWT is not connected to the
terminal upon delivery,make sure to connect it properly,
referring to “General installation” of this manual.
Avoid vibration or impact
and keep the FWT terminal
at a safe place to avoid
damage while you are not
using it
Do not use the FWT terminal
at a place where explosives
or flammable liquids are
present
Do not wipe the FWT terminal
with chemicals such as solvent
Remove the SMPS and the
backup battery if you do not
use the FWT terminal for
a long time
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지7
HWT-2150 7
User Guide
Before Using
Components check
Function Description of Each Component
Thank you for purchasing this product. Please check if the
components of the product are consistent with the figure below :
POWER LED
SERVICE LED
MODELED
ANT.
CHGLED
FWT terminal
Power supply (SMPS)
Serial RJ-11
DC Jack
Power Button
• POWER LED
Lighted when the external power is applied.
- When the external power is applied, the LED is red.
- When the internal power is applied, the LED is green.
- If the backup battery is connected, you can use the terminal without
the external power supply.
• SERVICE LED
Indicates status of the backup battery.
- LED OFF : Indicates that the service is not available as the
receive power intensity is weak.
Antenna
- LED blinking: Indicates that the service available although the
receive power intensity is weak.
- LED ON
: Indicates that the receive power intensity is strong
and the service is available.
• MODE LED
user Guide
Fixation Nuts
- RED : Indicates that the state is Voice Call.
- Green : indicates that the state is Data Service.
- Yellow : Indicates that the state is FAX Call.
- LED OFF : Indicates that the state is stand by.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지9
HWT-2150 9
User Guide
Before Using
• CHG LED
- RED : indicates that the state is in Charging.
• DC JACK
Feeds power from the SMPS of the FWT terminal.
- The AC input of the SMPS ranges 90~270V
• SERIAL PORT
A port for maintenance and data communication of the FWT terminal
Installation
General installation
1. Set the battery switch located at the bottom of the terminal to Off.
2. As shown in the figure below, open the cover on the rear side of
the terminal by pushing it along the arrow.
• RJ-11 JACK
Used to connect normal phones.
- As two jacks are presented, you can concurrently connect two
telephones without security assured.
- You may connect one telephone to any of the two jacks.
- You may connect up to five telephones to RJ-11 jack.
• POWER SWITCH
Connects power to the FWT terminal.
3. After the cover is open, you can see the backup battery and its
connector. As shown in the figure below, grip the connector to let
the flat side look downward. Then, push the connector along
the arrow to connect it to the circuit board.
backup battery connector
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지11
10
HWT-2150 11
User Guide
Installation
Note: The terminal may be damaged if you attach the connector
opposite to the direction shown above. Please double-check
the direction and proceed to step 4
6. As shown in the figure below, connect the telephone (normal phone)
to the jack RJ-11. You may use any of the two RJ-11 jacks provided
by the terminal.
4. After connecting the battery connector to the circuit board, insert the
cover as shown in the figure below. Then, fix the cover with
the screws.
7. Connect the SMPS for FWT terminal to the DC-jack located on the left
side of the terminal. Insert the power jack properly until it does not move
further.
5. As shown in the figure below, insert the antenna along the arrow and
rotate it clock-wise.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지13
HWT-2150 13
12
User Guide
Installation
8. Connect the power plug of the SMPS to the power receptacle.
Wall bracket Installation
1. In case of concrete wall, attach the Installation Sheet to the place
that you want and make holes with a drill.
Wall
AC plug
(110V or 220V)
Installation Sheet
25.0mm
9. Set the power switch located at the back of the terminal to ON.
2. As shown in the figure below, fix the screws into the holes.
The following actions occur :
•All of the four LEDs are lighted, and then the LED corresponding
to the power currently applied is lighted.
•If the service available, the SERVICE LED is lighted.
Wall
Screw
3.5mm
※ In case of wooden wall, skip drilling and directly fix the screws to the
Installation Sheet. The distance from the wall to the head of the
screw is the same as the figure in step 2.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지15
HWT-2150 15
14
User Guide
Installation
3. As shown in the figure below, insert A1 and A2 of the terminal to the
head of the screw and press the terminal downward to fix it.
Installation for data service
Computer
A1
A2
RS-232 Cable
Telephone
4.The following figure shows the shape after completion of Installation.
WLL
Terminal

Wall
Screw required to
tighten the terminal
to the wall.
※ You can get a batter call quality by installing the external panel antenna
(Please contact the distributor of the product for the antenna).
※ The FWT terminal has a backup battery to run without the external power
supply. If the SMPS for the FWT terminal is down, the terminal can run for
about 15 hours in waiting state and for about 2 hours in call state with
the backup battery.
As shown in the figure above, connect the serial port of the FWT terminal
to the PC COM1(COM2) with the RS232 cable. Data service subscribers
can purchase the RS232 cable from the service provider.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지17
HWT-2150 17
16
User Guide
Operation
Operation
Power On
- Using the external power
Connect the SMPS to the DC-Jack located on the left side of the
terminal and insert the power plug of the SMPS to the receptacle.
Insert the power jack properly until it does not move further. If power
is applied to the terminal, all of the four LEDs are lighted. Then, the
power LED is lighted and the service LED is lighted if the service
available.
- Using the backup battery
To use the backup battery of the terminal, set the battery switch at
the bottom to On. If you want to use the backup battery, it has to be
charged enough to operate the terminal. The battery is automatically
charged when the external power is applied. If power is applied to
the terminal, all of the three LEDs are lighted. Then, the battery LED
located at the center is lighted and the service LED located at the
bottom is lighted if the service available.
Power Off
Turn off the power switch located at the back of the terminal.
Call Send
- Normal Procedure
① Pick up the handset in on-hook status. You will hear the dial tone
(In case of No Service, you will hear the warning tone with 0.5Sec
interval).
② You can not send calls in No Service status (Service LED off).
③ Press the phone number of the called party and click the hook
switch (Hook-Flash).
④ Speak to the called party when the line is connected.
⑤ Hang up the handset after conversation.
- Redialing
Used to call to the phone number called latest.
① Pick up the handset and click the hook switch. The line is
connected to the number called latest. This function would not
work if you tried no call after power on
② Pick up the handset and click the hook switch. Refer to section
4.7 for the click time.
③ Hang up the handset after conversation.
- Speed Dialing
Before using this service, you have to set the speed dial function.
Refer to Section 4.1 for the setting method.
① In case of one digit
If the speed dial is 01_09, pick up the handset, press the number
(1_9), and then click the hook switch or press the latter digit long.
Speak to the called party when the line is connected. Hang up the
handset after conversation.
② In case of two digits
If the speed dial is 10_99, pick up the handset, press the number
(10_99), and then click the hook switch or press the first digit short
and second digit long.
Speak to the called party when the line is connected. Hang up the
handset after conversation.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지19
HWT-2150 19
18
User Guide
Operation
Call Receive
- When the Normal Phone is On-hook State
① Pick up the handset when the normal phone rings.
② Speak to the called party when the line is connected.
③ Hang up the handset after conversation.
- When the Normal Phone is Off-hook State
① Click the hook switch(hook-flash) if the normal phone receives the
ring signal (Call receive in off-hook is allowed only if the dial tone
& warning tone are being sent and the bell rings through the
buzzer).
② Speak to the called party when the line is connected.
③ Hang up the handset after conversation
Analog G3 Fax Service
To use the analog G3 fax service from the terminal equipped with the
analog G3 fax board, you have to send/receive documents
according to the following procedure:
- Sending Documents
Press [✽00] and then press the number of destination. The other
procedure is the same as that for general faxes.
- Receiving Documents
To receive documents from the analog G3 fax, set the terminal to the
Analog G3 fax receive mode first. Pick up the handset of the fax and
press [✽✽✽✽15✽]. The fax is set to the Analog G3 fax receive
mode(Set to Analog G3 fax receive mode until power off).
You can not receive voices unless you reset the Analog G3 fax
receive mode. To reset the Analog G3 fax receive mode, pick up the
handset of the fax and press [✽✽✽✽10✽]
Data Service
When a PC is connected to the WLL terminal, the data service can
provide Internet and PC communication and fax send/receive. As
wireless data communication service may not be provided
depending on service providers, please check if the service provider
provides this service. This service is available after purchasing data
communication cable from the service provider.
For computer environment setup and other details, refer to the User
Manual provided when you purchase the data communication cable.
- Data Service Receive Mode Setting
•Setting with a normal phone
This function is used to set the receive mode according to data
service type, using the normal phone connected to the WLL
terminal
① Pick up the handset of the normal phone and press
[✽✽✽✽10✽] to reset the data service receive mode.
② Pick up the handset of the normal phone and press
[✽✽✽✽11✽] to set fax receive mode(one time).
The fax receive mode is released automatically 10 minutes after
setting.
③ Pick up the handset of the normal phone and press
[✽✽✽✽12✽] to set fax receive mode
(Set to fax receive mode until power off).
④ Pick up the handset of the normal phone and press
[✽✽✽✽13✽] to set modem receive mode(one time).
The modem receive mode is released automatically 10 minutes
after setting.
⑤ Pick up the handset of the normal phone and press
[✽✽✽✽14✽] to set modem receive mode
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지21
HWT-2150 21
20
User Guide
Operation
(Set to modem receive mode until power off).
⑥ Default setting is [✽✽✽✽10✽].
•Setting with AT commands
This function is used to set the receiving mode according to data
service type,using the communication emulator program of PC
connected to the WLL terminal.
① Enter [AT+QCVAD=0] in the communication emulator program
and press the Enter key.
・After the setting is completed, OK is indicated and the data service
receive mode is released.
② Enter [AT+QCVAD=1] in the communication emulator program
and press the Enter key.
・After the setting is completed, OK is indicated and the fax receive
mode (one time) is set. The fax receive mode is released
automatically 10 minutes after setting.
③ Enter [AT+QCVAD=2] in the communication emulator program
and press the Enter key.
・After the setting is completed, OK is indicated and the fax receive
mode is set (Set to fax receive mode until power off).
④ Enter [AT+QCVAD=3] in the communication emulator program
and press the Enter key.
・After the setting is completed, OK is indicated and the modem
receive mode is set (one time). The modem receive mode is
released automatically 10 minutes after setting.
⑤ Enter [AT+QCVAD=4] in the communication emulator program
and press the Enter key.
After the setting is completed, OK is indicated and the modem
receive mode is set (Set to modem receive mode until power off).
⑥ Default setting is [AT+QCVAD=0].
Supplement Service
Speed dial
This function is used to save frequently used phone numbers in
advance and make a phone call quickly with the abbreviated code.
You can save up to 99 phone numbers. Default setting is off.
- Save phone number
Enter [##3233→1→1], enter a two-digit numbers(01~99) for the
address to save the phone number and press the [✽] button(save).
##3233→1→1→address(2 digits)→phone numbers→✽
: save phone numbers
- Delete phone number
Enter [##3233→1→2], enter the address(01~99) to delete and press
[✽] button. To delete all phone numbers saved, enter [##3233→1→
3] and press the [✽] button.
##3233 → 1 → 2 → address(2 digits) → ✽ : delete one address
##3233 → 1 → 3 → ✽
: delete all address
- Speed dial on and off
Enter [##3233→1→4] and then press the [✽] button(on). The speed
dial mode is enabled only if the speed dial function is on although
phone numbers are saved in the memory.
To disable the function(off), enter [##3233→1→ 5] and then press
the [✽] button.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지23
HWT-2150 23
22
User Guide
Supplement Service
##3233 → 1 → 4 → ✽
: speed dial on
##3233 → 1 → 6 → ✽
: emergency call hold on
##3233 → 1 → 5 → ✽
: speed dial off
##3233 → 1 → 7 → ✽
: emergency call hold off
- Speed Dialing
If the phone number is saved in the address and the speed dial function
is enabled(on), you can make a phone call by entering just the address.
If the saved address is one digit(01~09), press the latter digit long or
press it short and click the hook switch to make a phone call to the
saved number.
If the saved address is two digits(10~99), press the first digit short and
the second digit long or press the two digits short and click the hook
switch to make a phone call to the saved number.
If you attempt a call while the speed dial function is off, you will hear the
reject tone and fail to make a phone call.
- Emergency call
When phone numbers are stored in address 01~03 and the
emergency call is on, if you press the latter digits of the address long
or two digits short and click the hook switch, the call is connected to
the stored number and is held on as long as the called party does not
release.
If you attempt speed dialing when emergency call hold and speed dial
are enabled concurrently, the address 01~03 are operated in
emergency call hold mode.
If you attempt speed dialing when emergency call hold is off and
speed dial is on, the address 01~03 are operated in speed dial mode.
Reference: Warning Tone/Howler(ROH:Receiver Off-Hook) Tone
Emergency call hold
This function is used to register up to three phone numbers(Address
01~03) in advance to prepare for emergencies and quickly make a
phone call with the speed dial. The line connected is held on as long as
the called party does not release. Default setting is off.
- Emergency call hold on and off
Enter [##3233 → 1 → 6] and press [✽] button(on). The emergency call
hold function is activated when phone numbers are saved in address
01~03 and the emergency call is on. You can save phone numbers in
address 01~03 in the same way as "4.1.1" .
To deactivate the emergency call hold function(off), enter [##3233 → 1 →
7] and press the [✽] button.
If you pick up the handset (Off-Hook) and do not press buttons for the given time, the
dial tone changes to the warning tone. At this time, you can receive calls but can not
send calls as number input is not allowed. In this case, you have to put back the handset
(On-Hook) and pick it up again (Off-Hook) to attempt a call. If you hold the handset
after the dial tone has changed to the warning tone, the warning tone changes to the
Howler (ROH) Tone after the given time. You can hear the Howler Tone through the
buzzer. From that time on, you can not send or receive calls until you hang up (OnHook) the handset.
Reference: Confirmation Tone/Reject Tone
If you press the [✽] button(save) after all key operation for supplementary service
setting is normally accomplished, the telephone returns to the initial status after hookoff and the Confirmation Tone is sent to notify that the setting has been accomplished
normally. If an incorrect key is entered, a short reject tone is sent to notify the error.
Then, you can continue the operation from that step.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지25
HWT-2150 25
24
User Guide
Supplement Service
Hot Line Service
This function is used to register one frequently used number
(address 99) in advance and automatically make a phone call to
the number after hook-off. Default setting is Off.
Hot line is operated in 2 modes; timed hot line mode to connect
the line after the specified time (4sec~8sec) and immediate hot
line mode to connect the line just after off-hook.
- Hot line on and off
Enter [##3233→1→8→1].and press the [✽] button to set timed
hot line(On).
If a phone number is saved in addess 99 and the hot line function
is set to timed hot line mode, the line is connected the dial send
time (4sec~8sec) after hook-off.
Also, enter [##3233→1→8→2].and press the [✽] button to set
dial send time(4sec~8sec) after hook-off. Also, if a phone number is
saved in address 99 and the hot line function is set to immediate hot
line mode, the line is connected just after hook-off.
Reference:
When immediate hot line is on, you can not send calls to other numbers.
To make a phone call to other number, enter the setup mode by pressing the [#] button
within one second after hook-off and change the hot line mode.
Alarm reminder
If you set a time in advance, the alarm rings on the specified time
and stops when you pick up the handset. Default setting is off.
- Alarm reminder on and off
Enter [##3233→2→1] and four digits for a desired time(24 hours) and
immediate hot line(On).
press the [✽] button(on).
If a phone number is saved in address 99 and the hot line function
The alarm reminder function is automatically set to one time. The
is set to immediate hot line mode, the line is connected just after
alarm rings on the specified time and then the alarm reminder is
hook- off.
released (off).
If you want to activate the alarm at the same time everyday, enter
##3233 → 1 → 8 → 1 →✽ : Timed hot line on
[##3233→2→3→✽] to activate the alarm reminder and enter
##3233 → 1 → 8 → 2→✽ : Immediate hot line on
[##3233→2→4→✽] to deactivate it.
##3233 → 1 → 8 → 3→✽ : Hot line off
- Hot line calling
If a phone number is saved in address 99 and the hot line
function is set to timed hot line mode, the line is connected the
##3233 → 2 → 1 → Hour(4 digits, 24 hours) → ✽
: Alarm time input and setting (one time)
##3233 → 2 → 2 → ✽
: Alarm reminder on (one time)
##3233 → 2 → 3 → ✽
: Alarm reminder on (always)
##3233 → 2 → 4 → ✽
: Alarm reminder off
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지27
HWT-2150 27
26
User Guide
Supplement Service
Ear-piece volume control
Lock
This function is used to enter a password into the terminal to reject
calls from users who are not aware of the password.
If you attempt a call when the lock function is on, the warning tone is
heard and the call is not connected (Call receive is allowed).
H o w e v e r, if the emergency call function is on, origination of
emergency calls (address 01~03) is allowed. Default setting is off.
- Lock on and off
Enter [##3233→3] and a password of four digits. If you enter an
incorrect password, you will hear the reject tone. If the correct
password is entered, press [1] and then the [✽] button(lock on). To
release the lock function, enter [##3233→3→password→2→✽].
##3233 → 3 → password → 1 → ✽
: Locking on
##3233 → 3 → password → 2 → ✽
: Locking off
Used to control the volume of ear-piece. Default setting is Level3
[#### 03].
- Ear-piece volume control method
① Enter [##3233 → 4 → 1], enter a desired button out of 1(level 1),
2(level 2), 3(level 3), 4(level 4), 5(level 5), and then press the [✽]
button to save.
"1" is the smallest volume. The bigger the number is, the larger
the volume is.
##3233→4→1→1~5→✽ : Ear-piece volume(Method 1)
② Pick up the handset of the normal phone and press [####]. Enter
a desired number out of 01~05, and then press the [✽] button to
save. You will hear the dial tone after the volume control is
completed.
#### → 01~05 → ✽
: Ear-piece volume control (method 2)
- Password change
To change the password, press [##3233→3] and then enter the
password. Press[3], enter a new password and press the [✽]button.
Enter the new password again and press the [✽] button to change
the password to the new one.
##3233 → 3 → password → 3→new password →✽→new password→✽
: change password
Reference: The default password for lock is "0000".
Reset
Used to reset the terminal setup.
- Reset method
① Enter [##3233→4→0] and the lock code or the maintenance
code and then press [✽] button.
##3233 → 4 → 0 → ✽
: Reset
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지29
HWT-2150 29
28
User Guide
Supplement Service
Analog G3 Fax Standard Setting
Reset items and their status are listed below:
The terminal can provide fax service using two types of Analog G3
Items
Status
Speed dial
off
Emergency call hold
off
Hot line call
off
Alarm
off
Lock
off
PC Fax standard or the IS-707A.7 Analog G3 Fax standard. When
Ear-piece volume
level 3
IS-99/IS-707.4 based PC Fax standard is used, you have to select
CLIP Setting
As the terminal type FWT has no display, the calling party’s number
can be indicated by connecting a specific module or a display type
Fax standards.
This function is used to set the standard.
- Analog G3 Fax Standard Setting
Analog G3 Fax service is provided using the IS-99/IS-707.4 based
the default Fax receiving mode.
① IS-99/707.4 PC Fax setting
Enter [##3233 → 5 → Maintenance Code → 2 → 1], select “1”
(PC fax) or “2” (Analog G3 Fax), and then press the [✽] button to
save.
telephone. This function is used to set communication method of the
module.
##3233 → 5 → Maintenance Code → 2 → 1 → 1 or 2 →✽
: IS-99/707.4 PC Fax based mode setting
- CLIP Setting Method
① Enter [##3233 → 5 → Maintenance Code → 1 → 1(DTMF
mode) or 2 (FSK mode)] and press the [✽] button to save.
Reference: Default receiving mode is system-dependent (Unnecessary depending on
system configuration.). If the system is configured with single DN, the default receiving
##3233 → 5 → Maintenance Code → 1 → 1 or 2→ ✽
: CLIP setting
mode is not applied as Fax receiving depends on user’s receive mode setting (Data
receiving through the analog G3 Fax in case of ****15* and through the PC in case of
****12*). Also, if the system is configured with two DNs (if fax calls are received
Reference: The Maintenance Code “2733” is used only for maintenance.
according to the service option determined by the system), the terminal receives calls
according to the default receiving mode setting.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지31
HWT-2150 31
30
User Guide
Supplement Service
② IS-707A.7 Analog G3 Fax standard setting.
Enter [##3233 → 5 → Maintenance Code → 2 → 2] and press
the [✽]button to save.
##3233 → 5 → Maintenance Code → 2 → 2 → ✽
: IS-707A.7 Analog G3 Fax standard setting
Default Data Rate Setting
The terminal supports two types of data rates according to the
③ Setting IS-707.4 Rate Set 1 : Enter [##3233 → 5 → Maintenance
Code → 3], select “3”, and then press the [✽] button to save.
##3233 → 5 → Maintenance Code → 3 → 3 →✽
: Setting default data rate to RS1(IS-707.4 based)
④ Setting IS-707.4 Rate Set 2 : Enter [##3233 → 5 → Maintenance
Code → 4], select “4”, and then press the [✽] button to save.
##3233 → 5 → Maintenance Code → 3 → 4 →✽
: Setting default data rate to RS2(IS-707.4 based)
standards.
This function is used to set the default rate for data calls.
- Default Data Rate Setting
① Setting IS-99 Rate Set 1 : Enter [##3233 → 5 → Maintenance
Code → 3], select “1”, and then press the [✽] button to save.
##3233 → 5 → Maintenance Code → 3 → 1 → ✽
: Setting default data rate (8K) to RS1 (IS99)
② Setting IS-99 Rate Set 2: Enter [##3233 → 5 → Maintenance
Code → 3], select “2”, and then press the [✽] button to save.
##3233 → 5 → Maintenance Code → 3 → 2 → ✽
: Setting default data rate to RS2 (IS-99 based)
Ringer Frequency & Cadence Control
This function is used to control the ringer frequency and cadence.
Select the frequency first and then select the cadence. Default
setting is 20Hz, 1 sec On – 2sec Off.
- Ringer Frequency Setting
Enter [##3233 → 5 → Maintenance Code → 4]. Select a desired
number from 1 (16Hz) , 2 (20Hz) and 3 (25Hz).
- Ringer Cadence Setting
After selecting the frequency, select the cadence. Select a
desired number from 1~ 6 and press the * button to terminate
ringer frequency and ringer cadence setting.
No. 1: 1Sec On – 2 Sec Off
No. 2: 0.4 Sec On – 0.2 Sec Off - 0.4 Sec On – 2 Sec Off
No. 3: 1 Sec On – 4.5 Sec Off
No. 4: 1 Sec On – 4 Sec Off
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지33
HWT-2150 33
32
User Guide
Supplement Service
No. 5: 0.25 Sec On – 0.25 Sec Off - 0.25 Sec On – 1.25 Sec Off
No. 6: 2 Sec On – 4 Sec Off
##3233 → 4 → 3 → 1~3(frequency) → 1~6(cadence) →✽
: Ringer frequency & cadence setting
Default Vocoder Selection
The terminal provides service with three Vocorder types.
This function is used to select the Vocorder type.
- Vocoder Selection Method
Enter [##3233 → 5 → Maintenance Code → 6], select one of “1”
Dial Tone Frequency Control
This function is used to select the dial sent from the handset. Default
setting is 350 + 440Hz dual tone.
(8K EVRC) or “2” (13K QCELP) and then press the [✽] button to
save.
##3233 → 5 → Maintenance Code → 6 → 1 or 2 → ✽
: Vocoder selection
- Dial Tone Frequency Control Method
① Enter [##3233 → 5 → Maintenance Code → 5].
Select a desired number from 1 (350+440Hz) , 2 (400Hz) ,
3 (425Hz) and 4 (450Hz) and press the [✽] button.
##3233 → 5 → Maintenance Code → 5 → 1~4 → ✽
: Dial Tone Frequency Control (Method 1)
② Pick up the handset of the normal phone, press [####], and enter
a desired number out of 51 (350+440Hz) , 52(400Hz) , 53(425Hz)
and 54(450Hz).
#### → 51~54
: Dial Tone Frequency Control (Method 2)
Timed Hot Line Dial Send Waiting Time
Control
This function is used to control the hot line number send time when
the Timed Hot Line is On. The Hot Line number send time is
adjustable from 4 sec to 8 sec and default setting is 6 sec.
- Timed Hot Line Dial Send Waiting Time Setting
① Enter [##3233 → 5 → Maintenance Code → 7].
Select a desired number from 4 , 5 , 6 , 7 and 8 and press the [✽]
button.
For example, to set 7 sec, press 7 and the [✽] button.
##3233 → 5 → Maintenance Code → 7 → 4~8 →✽
: Timed Hot Line Dial send time setting (Method 1)
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지35
HWT-2150 35
34
User Guide
Supplement Service
② Pick up the handset of the normal phone, press [####], and then
select a desired number from 04~08. ‘04’ indicates automatic call
send after 4 seconds and ‘08’ indicates automatic call send after
eight seconds.
#### → 04~08
: Timed Hot Line Dial send time setting (Method 2)
Voice Privacy Setting
The terminal supports voice privacy.
- Voice Privacy On
Enter [##3233 → 5 → Maintenance Code → 9 → 1] and press the
[✽] button to save.
- Voice Privacy Off
Hook Flash Time (Click Time) Control
Enter [##3233 → 5 → Maintenance Code → 9 → 2] and press the
[✽] button to save.
This function is used to set the time required to recognize click of the
hook switch for redial and speed dial. Default setting is 100-700ms.
##3233 → 5 → Maintenance Code → 9 → 1 or 2 → ✽
: Voice Privacy on/off
- Hook Flash Time Control Method
① Enter [##3233 → 5 → Maintenance Code → 8 → 1], enter two
digits (05~98) for the minimum time by the 10msec, and then
press the [✽] button to save.
##3233 → 5 → Maintenance Code → 8 → 1 → 05~98 → ✽
: Hook Flash minimum time setting
② Enter [##3233 → 5 → Maintenance Code → 8 → 2], enter two
digits (06~99) for the maximum time by the 10msec, and then
press the [✽] button to save.
##3233 → 5 → Maintenance Code → 8 → 2 → 06~99 → ✽
: Hook Flash maximum time setting
Reference: If the minimum time is set to 50 ~ 90 msec, it is not available for dial pulse
type telephones.
Serial Interface Setting (None for HWP-2150)
The terminal supports data serve when it is connected to the PC
through RS-232 serial interface. The HWT-2150 terminal provides
two data rates for PC interface. It provides 115200 bps for highspeed packet data service and 19200 bps for modem, PC Fax and
low speed packet data service.
- Setting serial interface to 19200 bps
① Enter [##3233 → 5 → Maintenance Code → 0, select “1”], and
then press the [✽] button to save.
##3233 → 5 → Maintenance Code → 0 → 1 → ✽
: Setting the serial data baudrate to 19200 bps
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지37
HWT-2150 37
36
User Guide
Supplement Service
- Network Dial Tone Off
- Setting Serial Interface to 115200 bps
Enter [##3233 → 5 → Maintenance Code → 0, select “2”], and then
press the [✽] button to save.
Enter [##3233 → 6 → Maintenance Code → 2, select “1”], and then
press the [✽] button to save.
##3233 → 6 → Maintenance Code → 2 → 1 → ✽
##3233 → 5 → Maintenance Code → 0 → 2 →✽
: NIU-generated dial tone setting
: Setting the serial data baudrate to 115200 bps
- Network Dial Tone On
A Key Value Input
Enter [##3233 → 6 → Maintenance Code → 2, select “2”], and then
The terminal supports OTASP service that requires authentication.
This function is used to enter A key value required for the
authentication procedure.
press the [✽] button to save.
##3233 → 6 → Maintenance Code → 2 → 2 → ✽
: LE-Generated dial tone setting
- A Key Input
Enter [##3233 → 6 → Maintenance Code → 1], enter a number
corresponding to the A Key value up to 26 digits, and then press the
[✽]button to save.
##3233 → 6 → Maintenance Code → 1 →
System Parameter Input
You can enter/change channel number and MIN number of the
system parameters with the handset.
- Channel Number Input
A Key No.(26 digits) → ✽
: A Key input
Network Dial Tone Setting
The terminal provides the network dial tone depending on
configuration of the system (system dependent). The terminal
connected to a system that provides the network dial tone provides
“LE-Generated dial tone”. Other systems provide “NIU-generated
dial tone”.
Enter ##3233 → 9 → Maintenance Code → 1~4, enter three digits
of the channel number, and then press the [✽] button to save.
1 : Primary System A channel
2 : Secondary System A channel
3 : Primary System B channel
4 : Secondary System B channel
##3233 → 9 → Maintenance Code → 1~4 → Channel No. → ✽
: Channel number input
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지39
HWT-2150 39
38
User Guide
Supplement Service
- MIN Number Input
Enter ##3233 → 9 → Maintenance Code → 5, enter up to ten digits
for the MIN number, and then press the [✽] button to save.
##3233 → 9 → Maintenance Code → 5 → MIN No. → ✽
: MIN number input
Appendix
Summary table
##3233→1→1→address→phone number
##3233→1→2→address→✽
##3233→1→3→ ✽
##3233→1→4→ ✽
##3233→1→5→ ✽
##3233→1→6→ ✽
##3233→1→7→ ✽
##3233→1→8→1→✽
##3233→1→8→2→✽
##3233→1→8→3→✽
##3233→2→1→hour(4 digits, 24 hours) → ✽
##3233→2→2→ ✽
##3233→2→3→ ✽
##3233→2→4→ ✽
##3233→3→password→1→ ✽
On
##3233→3→password→2→ ✽
Off
Lock
# # 3 2 3 3→3→password→3→New password→ ✽→
Change password new password→ ✽
Ear-piece volume # # # #→ 01/02/03/04/05 → ✽ (01:Min ← 03:Middle → 0 5 : M a x )
adjusting ( 5 steps) # # 3 2 3 3→ 4→1→ 1 ~ 5→ ✽ ( 1 ~ 5 : s t e p 1 ~ s t e p 5 )
Reset
# # 3 2 3 3→ 4→0→ p a s s w o r d→ ✽
##3233 → 5 → Maintenance Code → 1 → 1 / 2 → ✽
Clip setting
( 1 : DTMF(BINA) Mode, 2 : FSK Bellcore Mode)
IS-99/707.4 PC
##3233 → 5 → Maintenance Code → 2 → 1 → 1 / 2 → ✽
Analog G3 Fax
Fax Mode
( 1 : PC Fax receiving default , 2 : Analog G3 receiving default )
Standard Setting
IS-707A.7 Mode
##3233 → 5 → Maintenance Code → 2 → 2 → ✽
##3233 → 5 → Maintenance Code → 3 → 1 / 2 / 3 / 4 → ✽
Default Rate Set
Save
Save/delete
Delete one address
phone number
Delete all addresses
On
Speed dialing
Off
Emergency call On
Off
hold
Time hot line on
Hot line
Immediate hot line
Off
Time input(one time)
One time mode
Alarm reminder
Always mode
Alarm off
(1 : RS 1 (IS99) , 2 : RS 2(IS99) , 3 : RS 1(IS707.4) , 2 : Rate Set 2 (IS707.4))
Ringer Frequency &
Cadence Control
##3233 → 5 → Maintenance Code → 4 → 1 / 2 / 3 (frequency)
→ 1 / 2 / 3 / 4 / 5 / 6 (cadence) → ✽
Dial Tone Frequency
Control
##3233 → 5 → Maintenance Code → 5 → 1 / 2 / 3 / 4 → ✽
( 1: 350+440Hz 2: 400Hz 3: 425Hz 4: 450Hz )
(Frequency 1: 16Hz 2: 20Hz 3: 25Hz / Cadence 1,2,3,4,5, 6 : Refer to 4.8.2)
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지41
HWT-2150 41
40
User Guide
Appendix
##3233 → 5 → Maintenance Code → 6 → 1/ 2 →✽
( 1 : 8K EVRC , 2 : 13K QCELP )
Timed Hot Line Dial ##3233 → 5 → Maintenance Code → 7 → 4 / 5 / 6 / 7 / 8 → ✽
Send Waiting Tim
( 4: 4 Sec 5: 5 Sec 6: 6 Sec 7: 7 Sec 8: 8 Sec )
Default
Vocoder S.O
Hook Flash
Time Control
Technical Specification
- 800MHz
##3233 → 5 → Maintenance Code → 8 → 1 (Min time) → 05~98 →✽
##3233 → 5 → Maintenance Code → 8 → 2 (Max time) → 06~99 →✽
( 05 ~ 99 : 50 msec ~ 990 msec)
On
##3233 → 5 → Maintenance Code → 9 → 1 →✽
Voice Privacy
Off
##3233 → 5 → Maintenance Code → 9 → 2 →✽
##3233 → 5 → Maintenance Code → 0 → 1 →✽
Serial Interface 19200 bps
Setting
115200 bps
##3233 → 5 → Maintenance Code → 0 → 2 →✽
A Key Value ##3233 → 6 → Maintenance Code → 1 → “AKEY” (26 digits) → ✽
( AKEY : 26-digit A Key value)
Input
NIU-generated Dial Tone ##3233 → 6 → Maintenance Code → 1 → 1 → ✽
Network Dial
Tone
LE-generated Dial Tone ##3233 → 6 → Maintenance Code → 1 → 2 → ✽
Air Interface
##3233→9→Maintenance Code→1(Primary A CH No.) →www (3digits)→✽
( www : Primary System A Channel No.)
##3233→9→Maintenance Code→2(Secondary A CH No.)→xxx (3digits)→✽
( xxx : Secondary System A Channel No.)
Channel
Number Input ##3233→9→Maintenance Code→3(Primary B CH No.)→yyy (3digits) →✽
( yyy : Primary System B Channel No.)
##3233→9→Maintenance Code→4(Secondary B CH No.)→zzz (3digits)→✽
MIN Number
Input
Analog G3 fax
receive
Data service
receive mode release
Fax receive mode
setting (one time)
Fax receive mode
setting(until power off)
Modem receive
mode (one time)
Modem receive
mode(until power off)
( zzz : Secondary System B Channel No.)
##3233→9→Maintenance Code→5→xxxxxxxxxx (10digits)→ ✽
( xxxxxxxxxx : MIN No.)
On (fax receive)
✽✽✽✽15✽
Off (voice receive)
✽✽✽✽10✽
✽✽✽✽10✽
Using the normal phone
[AT+QCVAD=0] → Enter key
Using the emulator
✽✽✽✽
11✽
Using the normal phone
Using the emulator
[AT+QCVAD=1] → Enter key
Using the normal phone
✽✽✽✽12✽
[AT+QCVAD=2] → Enter key
Using the emulator
Using the normal phone
✽✽✽✽13✽
Using the emulator
[AT+QCVAD=3] → Enter key
Using the normal phone
✽✽✽✽14✽
[AT+QCVAD=4] → Enter key
Using the emulator
Battery Back-up
Connectors for various
Service support
Physical
Environmental
Power Supply
Accessories
Common air interface standard → IS-2000
FREQUENCY → TX : 824 – 849MHz
RX : 869 – 894MHz
TX Output Power → 200mW
RX Sensitivity → - 104dBm
Vocoder → 8K/13K QCELP, 8K EVRC
Channel Bandwidth → CDMA 1.25Mhz
Spurious → TX : -61dBm below
RX : -81dBm below
MOD/DEMOD → O QPSK/QPSK
Frequency Accuracy → Fo°w300Hz
Type → Ni-MH
Capacity → 3.6V @ 1.8A
Talk Time → 2 Hours
Standby Time → 20Hours
RJ-11 → Standard wire-line telephone
Analog G3 Fax (Optional)
Serial port → Maintenance Purpose
Data Service Purpose ( Internet, PC Fax)
Dimension(D x W x H) → 180 x 180 x 57mm
Weight ( including Backup battery) → 546g
Operating Temperature → -10°C ~ +50°C
Storage Temperature → -20°C ~ +70°C
Input Power → 100 ~ 240Vw10%, 48~62Hz
Output Power → 5.5V 1.2A
Internal Antenna → Di-Pole Antenna
Power supply
External Antenna ( Optional ) → 10dbi Gain
Directional Panel Antenna
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지43
HWT-2150 43
42
User Guide
Appendix
Safety Information
1. SAFETY INFORMATION FOR FIXED WIRELESS TERMINALS
Troubleshooting
Trouble
Actions
When you hear no sound after hook-off?
•Check if the power LED or battery LED of the
terminal is on. If off, check if the SMPS power
plug is properly connected to the terminal.
•Check the RJ-11 Jack of the terminal connected
to the telephone.
When the service LED blinks or goes off?
•Check if the antenna is connected correctly, or
move the location of the terminal and check if
the service LED is on.
When you hear the warning tone instead of the
dial tone after hook-off?
•Check if the antenna is connected correctly, or
move the location of the terminal and check if
the service LED is on.
When the warning tone sounds"beep beep" when
you attempts a call?
•No call channel available or communication
failure with the base station. check if the service
LED is on and try again.
When calls are not connected with the warning
tone but you can receive calls?
•The lock function is on. Refer to section
'Ear-piece Volume control' of the user guide.
•If you are not aware of the password, please
contact the distributor or the service center.
When voice resounds during conversation?
•The resound removing function of the base
station is set improperly. Refer to section
'Ear-piece Volume control' of the user guide
for volume control.
When voice of the other party is not clear?
•Refer to section 'Ear-piece Volume control'
of the user guide.
When the battery LED blinks or goes off while
you are operating the terminal with the battery?
•Charge the backup battery with the SMPS as
the battery is discharged.
•POTENTIALLY EXPLOSIVE ATMOSPHERES
Turn your phone OFF when in any area with a potentially explosive
atmosphere and obey all signs and instructions.Sparks in such areas could
caus e an explosion or fire resulting in bodily injury or even death.
•INTERFERENCE TO MEDICAL DIVICES
Certain electronic equipment may be shielded against RF signal from you
wireless phone.(pacemakers,Hearing Aids,and so on)
Turn your phone OFF in health care facilities when any regulations posted in
these areas instruct you to do so.
RF signals may affect improperly installed or inadequately shielded electronic
system in motor vehicles.
•EXPOSURE TO RF ENERGY
Use only the supplied or an approved replacement antenna.
Do not touch the antenna unnecessarily when the phone is in use.
Do not move the antenna close to, or touching any exposed part of the body
when making a call.
2. SAR INFORMATION
THIS MODEL PHONE MEETS THE GOVERNMENT ’S REQUIREMENTS
FOR EXPOSURE TO RADIO WAVES.
Your wireless phone is a radio transmitter and receiver.It is designed and
manufactured not to exceed the emission limits for exposure to radio
frequency (RF)energy set by the Federal Communications Commission of the
U.S.Government.These limits are part of comprehensive guidelines and
establish permitted levels of RF energy for the general population.The
guidelines are based on standards that were developed by independent
scientific organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons,regardless of age and
health.
hWT-2150(8-9) 2003.8.9 11:51 AM 페이지45
44
Safety
The exposure standard for wireless mobile phones employs a unit of
measurement known as the Specific Absorption Rate,or SAR.The SAR limit set
by the FCC is 1.6 W/kg.*Tests for SAR are conducted with the phone
transmitting at its highest certified power level in all tested frequency
bands.Although the SAR is determined at the highest certified power level,the
actual SAR level of the phone while operating can be well below the maximum
value.This is because the phone is designed to operate at multiple power levels
so as to use only the power required to reach the network.In general,the closer
you are to a wireless base station antenna,the lower the power output.
Before a phone model is available for sale to the public, it must be tested and
certified to the FCC that it does not exceed the limit established by the
government-adopted requirement for safe exposure. The tests are performed
in positions and locations (e.g., at the ear and worn on the body) as required by
the FCC for each model. The highest SAR value for this model phone when
worn on the body with 2.5 cm separation distance as described in this user
guide, is 0.808 W/kg. (Body worn measurements differ among phone
models, depending upon available accessories and FCC requirements). While
there may be differences between the SAR levels of various phones and at
various positions, they all meet the government requirement for safe exposure.
The FCC has granted an Equipment Authorization for this model phone with all
reported SAR levels evaluated as in compliance with the FCC RF exposure
guidelines.SAR information on this model phone is on file with the FCC and
can be found under the Display Grant section of http://www.fcc.gov/oet/fccid
after searching on FCC ID PP4HWT-2150.
Additional information on Specific Absorption Rates (SAR)can be found on the
Cellular Telecommunications &Internet Association (CTIA)web-site at
http://phonefacts.net.*In the United States and Canada,the SAR limit for mobile
phones used by the public is 1.6 watts/kg (W/kg)averaged over one gram of
tissue.The standard incorporates a substantial margin of safety to give
additional protection for the public and to account for any variations in
measurements.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2003:08:09 11:51:22Z
Modify Date                     : 2004:02:16 23:29:23-08:00
Page Count                      : 23
Creation Date                   : 2003:08:09 11:51:22Z
Author                          : 1
Producer                        : Power Macintosh¿ë Acrobat PDFWriter 4.0
Mod Date                        : 2004:02:16 23:29:23-08:00
Metadata Date                   : 2004:02:16 23:29:23-08:00
Creator                         : 1

EXIF Metadata provided by EXIF.tools