Parker Hannifin MSLINK0007 200 Series Radio Module User Manual Exhibit D Users Manual per 2 1033 b3

Lord Corporation 200 Series Radio Module Exhibit D Users Manual per 2 1033 b3

Exhibit D Users Manual per 2 1033 b3

LORD Corporation 1/15/2018 Revision A Prepared by J. Dunklee 200 Series Radio Module Integration Guide 1. Overview The 200 Series Radio Module is an OEM device used to acquire data from LORD Corporation wireless sensing devices. It is designed to be embedded in other products to provide radio communication and data pass-through capabilities in a modular format. It is designed to be used with LORD data acquisition software or user software developed using the LORD MSCL code library. The module includes an integrated microcontroller/radio transceiver that communicates to LORD devices in the 2.4 GHz band. There are two radio transmission protocols that are available on the radio module – the standard 802.15.4 protocol (LXRS) and a LORD proprietary protocol (LXRS+). The modes are selectable in the LORD software. Both are capable of lossless transmission of continuous, burst, and other sampling modes, depending on sensor node capabilities. 2. Integration The radio module requires a PCB carrier board for proper integration. This board can be designed by LORD, or by an OEM customer with the information provided in this document. The carrier board provides power (+5 Vdc +/- 2%, 50mA) to the radio module, as well as the serial and input/output interface to connect the microcontroller to the larger communication system. The microcontroller code required to control the radio module is proprietary and is developed at LORD. The following section describes physical layout and pin configuration of the module. The module is 0.98” x 0.53”. It has either an internal antenna on one end of the board or an MMCX connecter used to interface with specified external antennas and cables. The interface to the carrier board is through solder pads around the three other sides of the board. For exact layout dimension of these pads, contact LORD Technical Support for an engineering file. The radio module is an OEM circuit board intended to be housed in an enclosure of the type suitable for the final product. It has no environmental protection by itself. Operating temperature range is -40 to +85 °C.
LORD Corporation 1/15/2018 Revision A Prepared by J. Dunklee Physical Interface Dimensions in inches Internal antenna location (if applicable) Carrier board solder pads (around board edge) External antenna connector location (if applicable)
LORD Corporation 1/15/2018 Revision A Prepared by J. Dunklee Pin Interface Radio Module pin number Signal name Description 1 DGND Digital ground 2 EFR32MG RESET Microcontroller reset 3 PF7 Microcontroller general purpose I/O 4 PF6 Microcontroller general purpose I/O 5 PF5 Microcontroller general purpose I/O 6 PF4 Microcontroller general purpose I/O 7 PF3 Microcontroller general purpose I/O 8 DBG_SWO Serial Wire Debug trace data output 9 DBG_SWDIO Serial Wire Debug data in/out 10 DBG_SWCLK Serial Wire Debug clock 11 PC11 Microcontroller general purpose I/O 12 PC10 Microcontroller general purpose I/O 13 PC9 Microcontroller general purpose I/O 14 PC8 Microcontroller general purpose I/O 15 PC7 Microcontroller general purpose I/O 16 PC6 Microcontroller general purpose I/O 17 DGND Digital ground 18 PD10 Microcontroller general purpose I/O 19 PD11 Microcontroller general purpose I/O 20 PD12 Microcontroller general purpose I/O 21 PD13 Microcontroller general purpose I/O 22 PD14 Microcontroller general purpose I/O 23 PD15 Microcontroller general purpose I/O 24 DGND Digital ground 25 VCC Module power input +5V dc 26 PB15 Microcontroller general purpose I/O 27 PB13 Microcontroller general purpose I/O 28 PB12 Microcontroller general purpose I/O 29 PB11 Microcontroller general purpose I/O 30 PA5 Microcontroller general purpose I/O 31 PA4 Microcontroller general purpose I/O 32 LED_RED Status LED red 33 LED_BLUE Status LED blue 34 LED_GREEN Status LED green 35 PA0 Microcontroller general purpose I/O 36 DGND Digital ground
LORD Corporation 1/15/2018 Revision A Prepared by J. Dunklee 3. Approved Antennas and Cables Model Description LORD Model Number Option Description Antenna Mfg PN Antenna Gain Integrated chip antenna 3022-0017 (not applicable) JOHANSON 2450AT45A100E 1.5 dBi External antenna 3022-0021 RPTNC outdoor rated antenna Laird Technologies 001-0042 2.0 dBi RPTNC standard antenna L-COM HG2403RD-RTF 3.0 dBi RPSMA, standard antenna Linx Technologies ANT-DB1-RAF-RPS 2.5 dBi MMCX antenna Data Alliance A9 1.5 dBi Cables up to one meter in length are approved to connect these antennas to the 200 Series Radio Module. Cables must be 50 ohm RF cable types, such as RG-178 and LMR-100, with applicable connectors. 4. Regulatory Marks a. Radio modules are labeled with the following FCC/IC ID number. b. Product assemblies with radio modules in them must be labeled “Contains 200 Series Radio Module” followed by the FCC/IC ID. c. The following notice applies to the radio module and must also appear in its entirety in the final product user manual. In addition, based on the antennas and power parameters specified for this device, it must be operated at least 2.52 cm from the operator to ensure RF levels do no exceed what is considered healthy for human exposure.

Navigation menu