Parker Hannifin MSLINK0007 200 Series Radio Module User Manual Exhibit D Users Manual per 2 1033 b3
Lord Corporation 200 Series Radio Module Exhibit D Users Manual per 2 1033 b3
Exhibit D Users Manual per 2 1033 b3
200 Series Radio Module Integration Guide 1. Overview The 200 Series Radio Module is an OEM device used to acquire data from LORD Corporation wireless sensing devices. It is designed to be embedded in other products to provide radio communication and data passthrough capabilities in a modular format. It is designed to be used with LORD data acquisition software or user software developed using the LORD MSCL code library. The module includes an integrated microcontroller/radio transceiver that communicates to LORD devices in the 2.4 GHz band. There are two radio transmission protocols that are available on the radio module – the standard 802.15.4 protocol (LXRS) and a LORD proprietary protocol (LXRS+). The modes are selectable in the LORD software. Both are capable of lossless transmission of continuous, burst, and other sampling modes, depending on sensor node capabilities. 2. Integration The radio module requires a PCB carrier board for proper integration. This board can be designed by LORD, or by an OEM customer with the information provided in this document. The carrier board provides power (+5 Vdc +/- 2%, 50mA) to the radio module, as well as the serial and input/output interface to connect the microcontroller to the larger communication system. The microcontroller code required to control the radio module is proprietary and is developed at LORD. The following section describes physical layout and pin configuration of the module. The module is 0.98” x 0.53”. It has either an internal antenna on one end of the board or an MMCX connecter used to interface with specified external antennas and cables. The interface to the carrier board is through solder pads around the three other sides of the board. For exact layout dimension of these pads, contact LORD Technical Support for an engineering file. The radio module is an OEM circuit board intended to be housed in an enclosure of the type suitable for the final product. It has no environmental protection by itself. Operating temperature range is -40 to +85 °C. LORD Corporation 1/15/2018 Revision A Prepared by J. Dunklee Physical Interface External antenna connector location (if applicable) Internal antenna location (if applicable) Carrier board solder pads (around board edge) Dimensions in inches LORD Corporation 1/15/2018 Revision A Prepared by J. Dunklee Pin Interface Radio Module Signal name pin number Description 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Digital ground Microcontroller reset Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Serial Wire Debug trace data output Serial Wire Debug data in/out Serial Wire Debug clock Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Digital ground Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Digital ground Module power input +5V dc Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Microcontroller general purpose I/O Status LED red Status LED blue Status LED green Microcontroller general purpose I/O Digital ground LORD Corporation DGND EFR32MG RESET PF7 PF6 PF5 PF4 PF3 DBG_SWO DBG_SWDIO DBG_SWCLK PC11 PC10 PC9 PC8 PC7 PC6 DGND PD10 PD11 PD12 PD13 PD14 PD15 DGND VCC PB15 PB13 PB12 PB11 PA5 PA4 LED_RED LED_BLUE LED_GREEN PA0 DGND 1/15/2018 Revision A Prepared by J. Dunklee 3. Approved Antennas and Cables Model Description Integrated chip antenna External antenna LORD Model Number Option Description Antenna Mfg PN JOHANSON 2450AT45A100E Antenna Gain 3022-0017 (not applicable) 1.5 dBi 3022-0021 RPTNC outdoor rated antenna Laird Technologies 001-0042 2.0 dBi RPTNC standard antenna L-COM HG2403RD-RTF 3.0 dBi RPSMA, standard antenna Linx Technologies ANT-DB1-RAF-RPS 2.5 dBi MMCX antenna Data Alliance A9 1.5 dBi Cables up to one meter in length are approved to connect these antennas to the 200 Series Radio Module. Cables must be 50 ohm RF cable types, such as RG-178 and LMR-100, with applicable connectors. 4. Regulatory Marks a. Radio modules are labeled with the following FCC/IC ID number. b. Product assemblies with radio modules in them must be labeled “Contains 200 Series Radio Module” followed by the FCC/IC ID. c. The following notice applies to the radio module and must also appear in its entirety in the final product user manual. In addition, based on the antennas and power parameters specified for this device, it must be operated at least 2.52 cm from the operator to ensure RF levels do no exceed what is considered healthy for human exposure. LORD Corporation 1/15/2018 Revision A Prepared by J. Dunklee
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Chris P. Townsend Comments : Company : MicroStrain, Inc. Create Date : 2018:01:31 10:54:03-05:00 Modify Date : 2018:01:31 10:54:04-05:00 Source Modified : D:20180131155355 Subject : Language : EN-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Metadata Date : 2018:01:31 10:54:04-05:00 Creator Tool : Acrobat PDFMaker 18 for Word Document ID : uuid:2164e005-5a1a-4db2-a16f-0b78ae8317f0 Instance ID : uuid:816b9db0-f5a0-4fee-9e7a-3ad295deb3e5 Format : application/pdf Title : Description : Creator : Chris P. Townsend Producer : Adobe PDF Library 15.0 Keywords : Page Layout : OneColumn Page Count : 4EXIF Metadata provided by EXIF.tools