Partner Tech EM200 E-MENU User Manual EM 200 User Manual EN Draft4 1 P3

Download:
Mirror Download [FCC.gov]
Document ID	1163368
Application ID	X2RbqLSbnxTl9ewazp9P6g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	113.12kB (1413975 bits)
Date Submitted	2009-09-02 00:00:00
Date Available	2009-09-02 00:00:00
Creation Date	2009-09-02 14:41:36
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2009-09-02 14:47:16
Document Title	EM-200_User_Manual_EN_Draft4-1 P3.pdf
Document Creator	Adobe InDesign CS3 (5.0)
Document Author:	joyce

EM-200
User Manual
Copyright
About this manual
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
This manual is intended for system administrators who are familiar with setting up a new system and
installing an operating system.
The manual consists of the following sections:
Chapter 1 Getting Started:
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Chapter 2 BIOS Setup Utility:
Chapter 3 Upgrading Components:
Appendix:
Trademark recognition
All product names used in this manual are the properties of their respective owners and are acknowledged.
This section covers unpacking and checking the
package contents, identifying components, installing the
battery pack, charging the battery and powering on.
The BIOS chapter provides information on navigating
and changing settings in the BIOS Setup Utility.
This section provides information on upgrading
components.
The appendix covers troubleshooting, information
on having the EM-200 serviced, and technical
specifications.
Safety information
Federal Communications Commission (FCC)
Before installing and using the EM-200, take note of the following precautions:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Read all instructions carefully.
Reorient or relocate the receiving antenna.
• Follow all warnings and cautions in this manual and on the unit case.
Increase the separation between the equipment and the receiver.
• When replacing parts, ensure that your service technician uses parts specified by the manufacturer.
• Do not place the unit on an unstable surface, cart, or stand.
• Do not block the slots and opening on the unit, which are provided for ventilation.
• Do not push objects in the ventilation slots as they may touch high voltage components and result in
shock and damage to the components.
• Do not place anything on the power cord. Place the power cord where it will not be in the way of foot
traffic.
• Avoid using the system near water, in direct sunlight, or near a heating device.
Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected.
• Never throw the battery into a fire or put it near a fire.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to
ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not
expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
Warning! Batteries may explode if not handled properly. Do not disassemble or dispose of them in fire. Keep them away from children. Follow
local regulations when disposing of used batteries.
WARNING
Declaration of conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
Your E-Menu is a data transmitter and receiver. It is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S.
Government.
These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
The guidelines are based on the safety standards previously set by both U.S. and international standards bodies:
American National Standards Institute (ANSI) IEEE. C95.1-1992National Council on Radiation Protection and
Measurement (NCRP). Report 86. 1986International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1996Ministry of Health (Canada), Safety Code 6.
The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and
health.The highest SAR value for this E-Menu tested by DASY5 for use at the body is 0.097 W/kg FCC RF Exposure
requirements:
SAR compliance for body-worn operations is restricted which provide at least 2 cm separation between the device
and the user’s body.
ᷴ㭊䢡✗㛛㏂曢㱇㛪㛰䇭䂟䙫⍘暑˛€⏖㛛㏂䂡⻇┭⻡字䙫䛟⏳曢㱇ㇽ䛟⏳❲
⻶曢㱇˛媲ᾄ㓁⻇┭媑㗵㛟㢫何曢㱇˛
娤⌈
䔏攀寖❲⏞䔜㱇㛛㍉ἁ㛰䇭䂟⍘晐⊈⾬㋰䅎寛㗵⣫何䔏⭳䙫䔜㱇˛
㮦⿍
Revision history
Version 1.0, August 2009
ii
TABLE OF CONTENTS
CHAPTER 1 GETTING STARTED ................................................ 1
Unpacking the machine..................................................................................1
Checking the package contents ....................................................................2
Identifying components .................................................................................3
Installing the battery pack ..............................................................................8
Charging the battery pack ..............................................................................9
Powering on .................................................................................................10
CHAPTER 2 BIOS SETUP ...........................................................11
About the Setup Utility .................................................................................11
Using the USB keyboard ..............................................................................11
Entering the Setup Utility ........................................................................12
BIOS Navigation Keys .............................................................................12
Using BIOS .............................................................................................13
Main Menu ...................................................................................................14
Advanced Menu ...........................................................................................15
► Boot Configuration ..............................................................................16
► IDE Configuration ................................................................................17
► Channel 1 Master ................................................................................18
Security Menu ..............................................................................................19
Boot Menu ....................................................................................................20
►Boot Device Priority ..............................................................................21
►Boot Type Order ...................................................................................21
Exit Menu .....................................................................................................22
CHAPTER 3 UPGRADING COMPONENTS ............................... 23
Safety and precautions ...............................................................................23
Before you begin ..........................................................................................24
Upgrading the hard drive..............................................................................25
Upgrading the memory module ....................................................................27
Upgrading the Mini-PCIE card .....................................................................28
APPENDIX .................................................................................. 31
Troubleshooting ...........................................................................................31
Tips for Troubleshooting ...............................................................................31
General Problems .......................................................................................32
Having the EM-200 Serviced ......................................................................33
Specification .................................................................................................34
iii
iv
CHAPTER 1
GETTING STARTED
Checking the package contents
After you unpack the device, check that the following items are included.
This chapter describes the procedures from unpacking the EM-200, to powering it on. The following topics
are described.
• Unpacking the machine on page 1
• Checking the package contents on page 2
• Identifying components on page 3
• Installing the battery pack on page 8
• Charging the battery pack on page 9
• “Powering on” on page 10
Unpacking the machine
The machine and cable accessories are packed in a cardboard carton with foam padding for protection during
shipping.
EM-200
Battery
Driver CD with drivers and the
user manual PDF file.
Protection pack
AC adapter
Figure 1.1 Unpacking the
machine
Carefully unpack the machine and keep the packing materials. If you need to ship it in the future, repack it as
shown in Figure 1.1.
If any item is missing or appears damaged, contact your dealer immediately.
C H A P T E R 1 G E T T I N G S TA R T E D
Power cord
Identifying components
This section describes the parts and connectors on the machine.
Left view
Front view
4 5
Figure 1.3 Left view
Component
Figure 1.2 Front view
Component
Description
Power indicator
Battery charging indicator
HDD status indicator
WiFi On/ Off indicator
Bluetooth On/ Off indicator
Built-in Microphone
Camera (optional)
10.1-inch touch panel
Description
5-in-1 media card slot
Express card 34 slot
USB port
Power button
RJ45 LAN jack
DC IN
C H A P T E R 1 G E T T I N G S TA R T E D
Right view
Rear view
Figure 1.4 Right view
Component
VGA port
USB port
Ventilation hole
Headphone jack
Microphone jack
Figure 1.5 Rear view
Description
Component
Description
Speaker
Battery pack
C H A P T E R 1 G E T T I N G S TA R T E D
Installing the battery pack
Bottom view
1. Overturn the EM200
so that the bottom is
facing up toward you, as
shown in the right. Slide
the battery release latch
to the unlock position.
2. Align EM200 battery
compartment pins to
the battery connector.
Slightly slide and press
the battery pack into the
compartment until the
battery lock switch is
bounced back.
Figure 1.6 Bottom view
Component
Description
Mounting hole
Camera (optional)
Battery lock switch
Memory, WiFi module, Bluetooth module slots
Battery pack
HDD compartment
Battery release latch
3. As shown in the right,
slide the battery release
latch to the lock position.
C H A P T E R 1 G E T T I N G S TA R T E D
Charging the battery pack
Powering on
Plug the AC adapter power cord into an electrical outlet, then connect the DC plug of the adapter cable to the
EM-200. It takes approximately 2–4 hours to fully charge the battery for the first time. Subsequent charges
might take longer.
The power button located on the left side of the EM200, press the power button the turn it on.
Charge the battery within a temperature range 0˚C to 45˚C.
NOTE
To protect and prolong the life of the battery, do not charge it for 24
hours or longer at a time.
IMPORTANT
IMPORTANT
Please make sure to perform 3 complete full charge and discharge
cycles to get optimal battery capacity. Failure to comply will result in
shorter battery lifespan.
To force power off , long press the power button for 4~5 seconds.
NOTE
10
C H A P T E R 1 G E T T I N G S TA R T E D
CHAPTER 2
BIOS SETUP
Entering the Setup Utility
Press the F2 key during booting to access the BIOS Setup Utility:
The primary function of the BIOS (Basic Input and Output System) is to identify and initiate component
hardware. The BIOS parameters are stored in non-volatile BIOS memory (CMOS). CMOS contents don’t get
erased when the computer is turned off. The following topics are described in this chapter.
Main
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Item Specific Help
•
•
•
•
•
•
•
About the Setup Utility on page 11
Using the USB keyboard on page 11
Main Menu on page 14
Advanced Menu on page 15
Security Menu on page 19
Boot Menu on page 20
Exit Menu on page 22
The BIOS Setup Utility enables you to configure the following items:
Hard drives, diskette drives, and peripherals
•
Password protection from unauthorized use
•
Power management features
•
Boot device priority
When changing the system configuration
•
When a configuration error is detected and you are prompted to make changes to the Setup Utility
•
When making changes to the Power Management configuration
•
When changing the User or Supervisor password
•
When changing the boot priority
Processor Type
Intel(R) Atom(TM) CPU N270
@ 1.66GHz
533 MHz
533 MHz
Cache RAM
0512 KB
Total Memory
1024 MB
System Time
System Date
[18:47:25]
[06/21/2009]
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
F9 Setup Default
F10 Save and Exit
Figure 2.1 Main BIOS menu
BIOS Navigation Keys
This Setup Utility should be used for the following:
•
GA-D1USB28 F04
System Bus Speed
System Memory Speed
About the Setup Utility
•
System BIOS Version
The BIOS navigation keys are listed below.
Key
Function
←→
Select the menu titles
↑↓
Select the items
Esc
Exits the current menu
Using the USB keyboard
F1
Displays a screen that describes all key functions
To enter the BIOS setup must use the external keyboard. Please connect USB keyboard and restart, then refer
to the section “entering the Setup Utility”.
F7/F8
Changes the selected field’s values
F9
Loads the setup default values
F10
Saves the current configuration and exits Setup
Enter
Selects or enters submenu
11
12
CHAPTER 2 BIOS SETUP
Using BIOS
Main Menu
When you start the Setup Utility, the main menu appears. A highlight indicates which option is currently
selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted,
execute the option by pressing .
Press right/left arrow key to select the Main menu, which displays the following screen:
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option.
Other options lead to dialog boxes that prompt you for information.
Main
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Item Specific Help
Some options (marked with a triangle ►) lead to submenus that enable you to change the values for the
option. Use the cursor arrow keys to scroll through the items in the submenu.
System BIOS Version
GA-D1USB28 F04
Processor Type
System Bus Speed
System Memory Speed
Intel(R) Atom(TM) CPU N270
@ 1.66GHz
533 MHz
533 MHz
Cache RAM
0512 KB
Total Memory
1024 MB
System Time
System Date
[18:47:25]
[06/21/2009]
Figure 2.2 Main menu
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
F9 Setup Default
F10 Save and Exit
System BIOS Version
This item shows the information about BIOS version.
Processor Type
This item shows the CPU type.
System Bus Speed
This item shows the FSB speed.
System Memory Speed
This item shows the memory clock speed.
Cache RAM
This item shows the size of the cache RAM.
Total Memory
This field displays the amount of memory detected by the system during boot.
System Time / Date
The Time and Date items show the current date and time held by the machine. These will be automatically
updated whenever you make changes to the Windows Date and Time Properties utility.
13
14
CHAPTER 2 BIOS SETUP
Advanced Menu
► Boot Configuration
Press right/left arrow key to select the Advanced menu, which displays the following screen:
Use this submenu to set the boot configuration. Select the item and press  to open the following menu:
Main
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Main
Item Specific Help
►Boot Configuration
►IDE Configuration
Advanced S3
Keyboard Language
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Item Specific Help
Boot Configuration
Numlock
[Off]
[Enabled]
[US, Chinese]
Figure 2.3 Advanced menu
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
Figure 2.4 Boot
Configuration submenu
F1 Help
ESC Exit
F9 Setup Default
F10 Save and Exit
Advanced S3
↑↓Select
Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
F9 Setup Default
F10 Save and Exit
Numlock
This item is used to enable/ disable the ACPI S3 mode, it can turn on and off the PC within seconds.
This item is used to turn on/off the numlock of the external keyboard at boot.
Keyboard Language
This item is used to select the keyboard language of external USB keyboard.
15
16
CHAPTER 2 BIOS SETUP
► IDE Configuration
► Channel 1 Master
Use this submenu to set the IDE configuration. Select the item and press  to open the following menu:
Use this submenu to set the hard disk drive, Select the item and press  to open the following menu:
Main
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Item Specific Help
IDE Configuration
HDC Configure as
ATA/IDE Mode
►Channel 1 Master
InsydelH2O Setup Utility
Advanced
[SATA Only]
[Native]
[WDC WD1600BEV1-222CT]
Figure 2.5 IDE
Configuration submenu
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
Channel 1 Master
[WDC WD1600BEVT-22ZCT]
Type :
[Auto]
Transfer Mode:
32Bit I/O:
Block Mode:
Transfer Mode:
S.M.A.R.T
Security Mode:
[Auto]




Uninstall
F9 Setup Default
F10 Save and Exit
F1 Help
ESC Exit
↑↓Select
Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
Item Specific Help
Figure 2.6 Channel 1
Master submenu
F9 Setup Default
F10 Save and Exit
HDC Configure as
Channel 1 Master
This item is used to select the hard disk interface type.
Displays the name of the current hard disk device in channel 1 master.
ATA/IDE Mode
Type:
This item is used to select the ATA/IDE mode.
If you leave this item at Auto, the system will automatically detect and configure the device it channel
1 master. If you change the value to User Defined and then manually configure the drive by entering the
characteristics of the drive in the fields described below:
17
18
•
32Bit I/O – when enabled, allows the system to improve the hard drive performance for 32Bit OS.
•
Block Mode – when enabled, allows the system to perform accesses to the hard disk in block mode.
•
Transfer Mode – displays the data transfer mode.
•
S.M.A.R.T – when enabled, allows the system to support S.M.A.R.T (Self-Monitoring, Analysis, and
Reporting Technology) for hard disk device.
•
Security Mode – displays the security mode status.
CHAPTER 2 BIOS SETUP
Security Menu
Boot Menu
The security system allows you to set a password to prevent unauthorized access to BIOS. Press right/left
arrow key to select the Security menu, which displays the following screen:
This menu allows the user to set the boot-related options. Press right/left arrow key to select the Boot menu,
which displays the following screen:
Main
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Main
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Item Specific Help
Supervisor Password :
User Password
Item Specific Help
Not Installed
Not Installed
Quiet Boot
[Enabled]
►Boot Type
Set Supervisor Password
Set User Password
Figure 2.7 Security menu
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
Figure 2.8 Boot Menu
F9 Setup Default
F10 Save and Exit
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
F9 Setup Default
F10 Save and Exit
Supervisor/ User Password
These two fields indicate if the Supervisor/ User Passwords are set or not.
Quiet Boot
When enabled, system will boot without message. In contrast, when disabled, system will boot in text mode.
Installed: System Password is set. Not Installed: System Password is not set.
Set Supervisor and User Passwords
These items can be used to install a password. A Supervisor password takes precedence over a User password,
and the Supervisor can limit the activities of a User. To install a password, follow these steps:
1. Highlight the item Set Supervisor/User Password on the Security menu and press .
2. The password dialog box appears.
Please type in your new password
3. If you are installing a new password, type in the password. You can type up to eight alphanumeric
characters. Symbols are ignored. The Set Supervisor/User Password item differentiates between
upper and lower case characters. Press  after you have typed in the password. To confirm the
password, type the password again and press . To clear the password, leave the dialog box
blank, press , when the confirm box appears, press  again.
4. Write the passwords down and keep them in a safe place.
Power on password
When enabled, system will ask input password on post time. When disabled, system will ask input password
when go to Setup Utility.
User Access Level
This item allows you to configure the user access level.
View Only - users can only view the Bios settings and can not change the settings.
Limited - allows users to change some settings.
Full - users can change all of the BIOS settings.
19
20
CHAPTER 2 BIOS SETUP
►Boot Device Priority
Exit Menu
Select the Boot Type item and press  to open the following menu:
This menu allows the user to save CMOS setting and exit the Setup Utility. Press right/left arrow key to select
the Exit menu, which displays the following screen:
Main
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Main
Item Specific Help
Boot Device Priority
Advanced
InsydelH2O Setup Utility
Security Boot Exit
Item Specific Help
►Boot Type Order
Exit Saving Changes
Exit Discarding Changes
Load Optimal Defaults
Discard Changes
Figure 2.9 Boot Device
Priority submenu
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
Figure 2.11 Exit Menu
F9 Setup Default
F10 Save and Exit
F1 Help
ESC Exit
↑↓
Select Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
F9 Setup Default
F10 Save and Exit
►Boot Type Order
This submenu allows the user to decide the order of boot devices to load the operating system. Select the Boot
Type item and press  to open the following menu:
Exit Saving Changes
Allows the user to save changes to CMOS and reboot the system. The following message is prompted when
the user presses  on the item.
InsydelH2O Setup Utility
Boot
Exit Saving Changes
Item Specific Help
Boot Type Order
[Yes] [No]
Hard Disk Drive
USB CD/DVD ROM Driver
USB Memory
Others
Exit Discarding Changes
Allows the user to exit Setup without saving changes to CMOS. The following message is prompted when
user presses  on the item.
Figure 2.10 Boot Type
Order submenu
Exit Discarding Changes
[Yes] [No]
F1 Help
ESC Exit
↑↓Select
Item
←→Select Menu
F7/F8 Change Values
Enter Select►Sub-Menu
Load Optimal Defaults
F9 Setup Default
F10 Save and Exit
Allows the user to load the default value in CMOS Setup. The following message is prompted when the user
presses  on this item.
Select a media type, and then use F7 or F8 key to move up or down the item in order to arrange the boot
priority.
Load Optimal Defaults
[Yes] [No]
Discard Changes
Allows the user to discard the changes. The following message is prompted when the user presses  on
this item.
Discard Changes
[Yes] [No]
21
22
CHAPTER 2 BIOS SETUP
CHAPTER 3
UPGRADING COMPONENTS
This chapter describes how to upgrade components for the EM-200. The following topics are described.
•
•
•
•
•
Before you begin
Make sure you have a stable, clean working environment. Dust and dirt can get into components and may
cause malfunction. Adequate lighting and proper tools can prevent you from accidentally damaging the
internal components.
Most of the electrical and mechanical connections can be disconnected by using your fingers. It is
recommended that you do not use needle-nosed pliers to disconnect connectors as these can damage the soft
metal or plastic parts of the connectors.
Safety and precautions on page 23
Before you begin on page 24
Upgrading the hard drive on page 25
Upgrading the memory module on page 27
Upgrading the Mini-PCIE card on page 28
To prevent scratching the case of the machine, make sure the worktop
surface is clean and flat.
Safety and precautions
CAUTION
Computer components and electronic circuit boards can be damaged by discharges of static electricity.
Working on computers that are still connected to a power supply can be extremely dangerous. Follow these
guidelines to avoid damage to the computer or injury to yourself.
• Always disconnect the unit from the power outlet.
• Leave all components inside the static-proof packaging that they ship with until they are ready for installation.
• After replacing optional devices, make sure all screws, springs, or other small parts are in place and are
not left loose inside the case. Metallic parts or metal flakes can cause electrical shorts.
Only qualified personnel should perform repairs on the machine.
Damage due to unauthorized servicing is not covered by the warranty.
If you are not confident of installing a hard drive, memory card or LAN
CAUTION card, we recommend that you refer the job to qualified personnel.
If the LCD breaks and fluid gets onto your hands or into your eyes,
immediately wash with water and seek medical attention.
WARNING
WARNING
The inverter card has high voltage. Do not touch the inverter card while
power is connected to the machine. Unplug the power cord before
attempting to replace any part.
To prevent static damage to components, wear a grounded wrist strap.
Alternatively, discharge any static electricity by touching the bare metal
chassis of the unit case, or the bare metal body of any other grounded
CAUTION appliance.
Hold electronic circuit boards by the edges only. Do not touch the
components on the board unless it is necessary to do so. Do not flex or
stress the circuit board. Do not hold components such as a processor
CAUTION by its pins; hold it by the edges.
23
24
CHAPTER 3 UPGRADING COMPONENTS
Upgrading the hard drive
7. Remove the hard drive.
Refer to the following to remove and replace the hard drive.
1. Turn off the EM-200.
2. Disconnect the AC adapter
cable.
3. Overturn the EM200.
4. Remove the two screws as
shown in the right.
8. Remove the four screws, then
remove the hard drive out from
the tray.
5. Open and remove the hard drive
compartment cover.
To replace the hard drive, reverse the above procedure.
6. Slide the hard drive to
disconnect.
25
26
CHAPTER 3 UPGRADING COMPONENTS
Upgrading the memory module
7. Pop out the two silver latches
holding the memory module
into place. The module pops
up. Grasp the outer edges of the
memory module with thumb
and forefinger, and then gently
remove it.
Refer to the following to remove and replace the memory.
1. Turn off the EM-200.
2. Disconnect the AC adapter
cable.
3. Overturn the EM200.
4. Remove the two screws as
shown in the right.
To replace the memory module, reverse the above procedure.
Upgrading the Mini-PCIE card
Refer to the following to remove and replace the PCIE card.
1. Turn off the EM-200.
2. Disconnect the AC adapter
cable.
3. Overturn the EM200.
4. Remove the two screws as
shown in the right.
5. Open and remove the memory
module compartment cover.
5. Open and remove the MiniPCIE card compartment cover.
6. Locate the memory module, as
shown in the right.
27
28
CHAPTER 3 UPGRADING COMPONENTS
6. Locate the Mini-PCIE card, as
shown in the right.
7. Remove the screw on the MiniPCIE card, Mini-PCIE will pop
up 45 degree.
8. When it pops up, gently remove
it.
To replace the Mini-PCIE card, reverse the above procedure.
29
30
CHAPTER 3 UPGRADING COMPONENTS
APPENDIX
General Problems
Refer to the following general problems you may encounter.
This appendix describes locating and solving problems that you may encounter while using the EM-200.
PROBLEM
SOLUTION
Troubleshooting
The display screen is dark.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection.
Check the following before proceeding to the problem-specific solutions.
Make sure that the EM-200 is not in suspend
mode.
An incorrect date and time are displayed.
Set the date and time in BIOS or Operation
System.
Tips for Troubleshooting
Cannot be turned off after crash.
Long press the power button for 4 seconds to force
shutdown.
In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem
more quickly. Try to pin point the problem and thus avoid replacing non-defective parts. For example, if you
replace batteries and the problem remains, put the original batteries back and go to the next step.
Cannot be powered on
Connect the AC adapter, if it can be powered on,
there is insufficient battery power. If it still unable
to be powered on after charging, please have the
EM-200 serviced.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for
technical support or for passing on to service personnel.
•
Use some other electrical device to confirm that the electrical outlet is working.
•
Ensure all connections are securely attached.
31
32
APPENDIX
Having the EM-200 Serviced
Specification
If you are unable to solve the problem, you should have the terminal serviced. Pack the terminal in the
original carton. (See “Unpacking the EM-200” on page 1.) Include a description of the problem and a
checklist of the steps you took when trying to fix the problem. The information may be useful to the service
personnel. Return the terminal to the place you purchased it.
Processor
Intel Atom 1.6GHz Processor (N270)
BIOS
1024K BB Flash ROM
Chipset
Intel 945GSE
Memory
Memory DDRII SO-DIMM X 1, 1GB, support up to 2GB
LCD Display
10.1” TFT-LCD, 1024x600, 200 nits, LED backlight
With Touch Panel
Resistive touch
Graphics
Integrated in Intel 945GSE graphics controller
Hard Disk Drive
One 2.5" 160GB SATA HDD
Bluetooth
Bluetooth 2.1
Ethernet 10/100 Base T
LAN & WiFi
IEEE 802.11b/g/n
5-in-1 Media Card Slot x 1
Mini-PCIe Slot x 2 (Internal)
Express Card 34 Slot x 1
Interface I/O Port
USB Port x 3
Audio Jack x 2 (Mic-in and Headphone out)
VGA D-Sub x 1
DC-in x1
Speaker
1 Watt x 2
Touch panel
Input Devices
Internal Mic-in
33
System Status LED
Power on/Suspend, Battery Charging, HDD Access, RF, Caps Lock, Number Lock
Buttons & Switch
Power on/off switch
WebCam
1.3M Pixel CMOS webcam integrated (optional)
Battery Pack
DC 7.4v, 4,500mA Li-polymer battery
Battery life
up to 3 hrs (estimate)
Dimensions (W x
H x T)
189 x 268 x 25.7mm
Weight
1,250g
34
APPENDIX

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Instance ID                     : uuid:594b0adf-87a2-48fd-85d9-9c33fa51d09f
Document ID                     : adobe:docid:indd:f85d9bdc-1d0b-11dd-9927-e84cdd3fef76
Rendition Class                 : proof:pdf
Derived From Instance ID        : f85d9bdb-1d0b-11dd-9927-e84cdd3fef76
Derived From Document ID        : adobe:docid:indd:4fcda41b-4e75-11dc-9efb-a6e7d4bf122d
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:95A397AA8118DE118662D1DAC27A53C9, uuid:0a54245e-7004-4976-8367-5dcd2363d957, uuid:b591ff80-0af1-4b83-8d02-2ab70a993334, uuid:b591ff80-0af1-4b83-8d02-2ab70a993334, uuid:b591ff80-0af1-4b83-8d02-2ab70a993334, uuid:d3da5787-b691-45a1-8979-5b27beb4855c, uuid:6f36e402-8860-4814-ae2c-58e7a93e9b9f, uuid:cc4801fb-acac-4e98-bce8-9d8fef298564, uuid:fb805101-5582-45fd-9fa4-4d272fb7245e, uuid:45a1ed69-9ac3-4fc2-be2c-33bf565603ee, uuid:15a1d06d-bf76-499f-9342-5421785afc0b, uuid:60b464a0-b4fc-4db7-813a-6cdbb1875aae, uuid:60b464a0-b4fc-4db7-813a-6cdbb1875aae, uuid:60b464a0-b4fc-4db7-813a-6cdbb1875aae, uuid:60b464a0-b4fc-4db7-813a-6cdbb1875aae, uuid:f01870a8-dccf-4b05-aab8-de6aa01c8875, uuid:34a500e1-859b-4169-9138-4c1e55effb63, uuid:6190845b-840f-45fb-93b7-4e56d0b54493, uuid:0a6fd3f0-9b4d-411a-9192-34418df42dd1, uuid:c2a47281-5469-4442-9edb-6ed9c3ece3ee, uuid:60b464a0-b4fc-4db7-813a-6cdbb1875aae, uuid:ff0d6b9d-7bea-4568-8ba5-5cf7a582e009, uuid:633d1acc-737e-496b-bff1-3c6d0a208e06, uuid:ff0d6b9d-7bea-4568-8ba5-5cf7a582e009, uuid:988009dc-4c51-481a-a408-5087cc4e02f5, uuid:60b464a0-b4fc-4db7-813a-6cdbb1875aae, uuid:633d1acc-737e-496b-bff1-3c6d0a208e06, uuid:e2b56871-8638-4348-85c3-54dcaef3f317, uuid:e2b56871-8638-4348-85c3-54dcaef3f317, uuid:76fabb8f-b379-4148-8d33-059f9e064dbf, uuid:1d868c6c-1c9f-4240-9e50-6dc87d761fa7, uuid:1c7db1a7-9890-4955-a590-97a546376f5a, uuid:371bc38f-3a4f-4d6a-97a3-d160a8ba3702, uuid:dee8ee1f-26cd-428d-a587-3a0278a71aea, uuid:0e1ac544-08b1-48c1-a845-56385b7e657c, uuid:1c2c1a9c-29cb-4414-b342-ca3e5d05e0da, uuid:00d72ac5-5ecf-484f-ba4c-74b07a929edc, uuid:0b64d467-83e1-4487-a54a-4673e2391bd4, uuid:853c2da0-be24-4cc7-88d3-196137708fc1, uuid:6a953d62-c84b-4474-9525-bdfcaa5afbc1, uuid:c050a59a-474a-4a0f-af1a-3b3ab92cc85c, uuid:01303ebe-1720-4da7-b1bd-aa7a49dfda78, uuid:c8b430e5-6029-473f-ac69-334638a7a137, uuid:bf11a1d3-65d2-4644-8980-1bdf1acaee8d, uuid:512b6e54-dd9b-4e08-8f08-8431396df5e9, uuid:fcdb6083-ec52-49fb-abeb-1b55b00fac29, uuid:4d05fb42-ba9a-4014-9d60-890936e0bd5f, uuid:e416369c-2fa7-4df0-939c-5a42cc48c878, uuid:de86a371-b2e9-4fca-bd14-c181ef1cf9bb, uuid:3712fa9a-458a-475d-af17-b8298b2a411d, uuid:da6fa43b-bd02-4960-9364-1074468d984c, uuid:d9c34a93-c10e-4860-b34c-414c71b31271, uuid:de86a371-b2e9-4fca-bd14-c181ef1cf9bb, uuid:3712fa9a-458a-475d-af17-b8298b2a411d, uuid:1b13a5a8-c49e-496e-991b-0e00a48be32f, uuid:0a7fecad-ae6c-4c10-8790-c1ee8e61774d
Manifest Reference Document ID  : uuid:94A397AA8118DE118662D1DAC27A53C9, xmp.did:70FB30A80776DE118CA5E2EA7DA66850, xmp.did:EE21656A9A44DE119B1FD6B00A39336D, xmp.did:EE21656A9A44DE119B1FD6B00A39336D, xmp.did:EE21656A9A44DE119B1FD6B00A39336D, xmp.did:D72510496778DE118560BCD9E2C3A283, xmp.did:DCA85B35B881DE1192C9A874ECB3D97C, xmp.did:1738DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:1938DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:1838DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:1A38DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:32723A4D2263DE11897FF8BA82845BBC, xmp.did:32723A4D2263DE11897FF8BA82845BBC, xmp.did:32723A4D2263DE11897FF8BA82845BBC, xmp.did:32723A4D2263DE11897FF8BA82845BBC, xmp.did:33723A4D2263DE11897FF8BA82845BBC, xmp.did:1D38DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:1B38DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:1E38DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:1F38DA78635EDE11AFDAD7FBD43C5D0E, xmp.did:32723A4D2263DE11897FF8BA82845BBC, uuid:3aa74f57-5a06-4ebf-a817-f56e8130bb45, uuid:56107cc5-9fa8-44ce-90d8-49e1c6a4dc44, uuid:3aa74f57-5a06-4ebf-a817-f56e8130bb45, xmp.did:C88F8BB2915EDE11AFDAD7FBD43C5D0E, xmp.did:32723A4D2263DE11897FF8BA82845BBC, uuid:56107cc5-9fa8-44ce-90d8-49e1c6a4dc44, xmp.did:34723A4D2263DE11897FF8BA82845BBC, xmp.did:34723A4D2263DE11897FF8BA82845BBC, uuid:FF3246E8AD66DE11A191BD1D4B45D348, xmp.did:683843C9156ADE11B29AC9C8614A5B41, uuid:FB3246E8AD66DE11A191BD1D4B45D348, xmp.did:C49F5990116EDE119B6BF02E663B124A, xmp.did:C59F5990116EDE119B6BF02E663B124A, uuid:D6835DD8B266DE11A191BD1D4B45D348, uuid:DB835DD8B266DE11A191BD1D4B45D348, uuid:DF835DD8B266DE11A191BD1D4B45D348, xmp.did:9EF41F76E16EDE119E6EA81CC916B423, xmp.did:9FF41F76E16EDE119E6EA81CC916B423, xmp.did:A0F41F76E16EDE119E6EA81CC916B423, xmp.did:A1F41F76E16EDE119E6EA81CC916B423, xmp.did:A2F41F76E16EDE119E6EA81CC916B423, uuid:F2EB605AD566DE11A191BD1D4B45D348, xmp.did:8F74C06DD16FDE11BA5DC31154E8086A, xmp.did:9074C06DD16FDE11BA5DC31154E8086A, xmp.did:9174C06DD16FDE11BA5DC31154E8086A, xmp.did:9274C06DD16FDE11BA5DC31154E8086A, xmp.did:9374C06DD16FDE11BA5DC31154E8086A, xmp.did:9674C06DD16FDE11BA5DC31154E8086A, xmp.did:E4FF02FA5D71DE11BA5DC31154E8086A, xmp.did:9874C06DD16FDE11BA5DC31154E8086A, xmp.did:E6FF02FA5D71DE11BA5DC31154E8086A, xmp.did:9674C06DD16FDE11BA5DC31154E8086A, xmp.did:E4FF02FA5D71DE11BA5DC31154E8086A, xmp.did:E7FF02FA5D71DE11BA5DC31154E8086A, xmp.did:E9FF02FA5D71DE11BA5DC31154E8086A
Create Date                     : 2009:09:02 14:41:36+08:00
Modify Date                     : 2009:09:02 14:47:16+08:00
Metadata Date                   : 2009:09:02 14:47:16+08:00
Creator Tool                    : Adobe InDesign CS3 (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 8220 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : EM-200_User_Manual_EN_Draft4-1 P3.pdf
Creator                         : joyce
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Trapped                         : False
Page Count                      : 20
Author                          : joyce

EXIF Metadata provided by EXIF.tools