Paxton Access 380127 Proximity LCD Reader User Manual INSTRUCTION PROXIMITY LCD reader

Paxton Access Ltd Proximity LCD Reader INSTRUCTION PROXIMITY LCD reader

User Manual

Download: Paxton Access 380127 Proximity LCD Reader User Manual INSTRUCTION   PROXIMITY LCD reader
Mirror Download [FCC.gov]Paxton Access 380127 Proximity LCD Reader User Manual INSTRUCTION   PROXIMITY LCD reader
Document ID1157920
Application IDwTAcIX5vIAGk/nTbZJwSQQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize135.86kB (1698264 bits)
Date Submitted2009-08-24 00:00:00
Date Available2009-08-25 00:00:00
Creation Date2009-08-13 11:37:21
Producing SoftwareAdobe PDF Library 7.0
Document Lastmod2009-08-13 11:38:02
Document TitleINSTRUCTION - PROXIMITY LCD reader
Document CreatorAdobe InDesign CS2 (4.0.5)

22/07/2009
0AXTON !CCESS
Ins-30091-US PROXIMITY LCD reader
Technical Support
1.800.672.PAXT
Technical help is available:
support@paxton-access.com
Monday - Friday from 12:00 AM - 5:00 PM (PST)
Saturday from 1:00 AM - 5:00 AM (PST)
Documentation on all Paxton Access products can be found on our web site - http://www.paxton-access.com/
Suitability
Security sensitive doors
Mounted on metal surface
Wet environments
Readers mounted together
12 inches
between readers
The main visible face of the reader is a full color backlit LCD screen.
This can be configured to display images of the customer’s choice.
For example, an image using a company name/logo could be used
as the default display on each reader around the site.
The LCD reader comes with four preloaded images. These can
replaced using an uploader program via a Net2Air USB bridge or a
Net2Air USB dongle.
The LCD reader will accept:
Switch2, Net2 and EM4100 tokens.
Net2 hands free tokens (if an interface is fitted).
Fitting
The LCD reader is surface mounted onto the wall using
the backplate and fixings provided. It can be positioned
to allow display of Portrait or Landscape images.
Fix the mounting plate to the wall, noting the position of
the orientation arrow (see diagram).
Make a hole in the wall to take the reader cable and
feed this through. Ensure there will be sufficient slack to
allow the reader to slide over the mounting plate during
installation.
Present the reader to the mounting plate so that the
slots pass over the side tabs in the plate.
Slide the reader down the plate until the retaining pin clicks into position.
A tool is provided with the reader to depress this pin should the reader ever need to be removed.
Image Download
The unit comes with four preloaded images. These relate to the 3 LED’s (Green, Amber and Red) on a
standard Paxton Access reader plus a default image.
Once a token has been read, the control unit establishes the access permissions of that user. Access is
granted or denied as appropriate with the designated image displayed. For example, if access is denied
the image assigned could show “Please return to Reception”.
Page 
Wiring
Connection to a control unit
reader port
Connection modules
Reader junction box (325-020-US)
This module can be used to provide a connection point
for the reader RJ45 plug. The terminals on the module
are then wired color for color to the controller.
Alternatively, the reader can be wired directly into the
screw terminals of the control unit by first cutting off
the RJ45 plug and stripping back the wires in the cable.
Reader Port Module (325-030-US)
This module may be purchased separately to speed up
the installing and replacement of readers.
The reader port module is designed to convert the
standard reader ports on Switch2 and Net2 controllers
to accept one or two RJ45 connections. Pull off the
screw terminal block from the reader port and simply
replace it with this module.
Further information on how to purchase Installer Tools is available at:
http://paxton.info/841
Cable extensions
Readers can be extended using Belden CR9540 10-core overall screened cable. The maximum length is 100 yards.
Page 
Image preparation
You can replace any of the 4 default images with your own customised versions. These images must
be prepared using a 3rd party software package.
The following limitations apply:
Portrait image:		
Landscape image:
Image format:		
240 x 320 pixels - minimum
320 x 240 pixels - minimum
.bmp, .jpg, .gif, .png
Any image that is larger than these dimensions will align itself with the top left corner of the display.
It will NOT self centre.
Image Uploader
Images cannot be retrieved from the reader but they can be refreshed or replaced using an uploader program.
The program can be found in the Net2 CD/Tools folder or by download from < http://paxton.info/1521 >
The program will detect any LCD readers that are in Net2Air range. They are listed along with their Net2Air signal
strength. Highlight the required reader, select one of the four image types and browse the PC for the required
image. Click on ‘Send image’ and this will be uploaded to the selected reader.
Image orientation
The metal backplate is marked with an Arrow. Click
on the ‘Rotation’ option to turn the green arrow into
the same direction as the backplate arrow.
This display is used to confirm that the image
transmitted to the reader will match the orientation
of the reader as installed. Rotating this display
image does NOT alter the actual image.
In the example on the left, we have set the
rotation to show a reader installed in a landscape
orientation. This shows that the current image, if
sent, would display incorrectly. (i.e. sideways)
The image should be corrected and viewed again
before final transmission to the unit.
Page 
Detecting the LCD reader
Plug the USB Net2Air bridge or Net2Air USB dongle into the PC.
Run the Image uploader software and it will detect the USB Net2Air device connected to the PC.
The PC will then detect and display any LCD units that are in range of the USB device
Image selection
The LCD reader will hold 4 images. These are selected automatically by the reader’s LED control wires. The
default image will display unless one of the three LED’s lines is individually active. In that case the corresponding
image (Access Granted, Access Denied or Enter PIN) will display. The supplied images are shown below.
Image download
Select the LCD reader from the list of units detected and the image type that is to be updated. Make sure that the
orientation arrow is correct and then browse for the file to be uploaded.
Check that the image is correct and then click on the ‘Send Image’ button.
This will bring up a password security screen. The reader password is left blank when supplied but one can be
created if required.
The image will upload to the LCD reader in about 90 seconds and reports the progress on a Status bar.
Changing the reader name
The name is stored within the reader. Select the reader, click the ‘Change LCD reader name’ button and you will
then need to enter the password (if set). The reader name can then be changed.
Changing the reader password
The password is stored within the reader itself. Select the unit, click the ‘Change LCD reader password ‘ button.
You will be asked to enter the old password and the new password.
Factory reset
The reader can be reset to a factory default state by carrying out the following operation:1.
2.
3.
4.
Connect together the yellow and green wires. (reset link)
Connect power to the reader.
The reader will beep 3 times to confirm the reset sequence.
Remove the power and remove the reset link.
This factory reset sequence results in the LCD reader images returning to the default images, the LCD reader
name will be cleared and the reader password will be blanked.
Page 
Specifications
Environment
Operating temperatures - all items
Min
Max
-20 °C (-4 °F)
+55 °C (+131 °F)
Waterproof
IPX7
Outdoor Use
Cable length
5 yards
Silent operation feature
Yes
Electrical
Min
Max
DC supply voltage
8V DC
14V DC
DC supply current
165 mA
215 mA
125 kHz
Carrier frequency
Clock and data bit period
600 µs
Dimensions
Read Range
Width
Height
Depth
5/8
1/4
1 inch
inch
inch
Token
Keyfob
Hands Free Token
2 1/2 inch
2 1/4 inch
16 inch
Contents in box
PROXIMITY LCD reader
Reader mounting plate
Documentation
Option
Fixing Kit - LCD reader
Description
Qty
fk1-087
No 6 x 3/4 in pozi pan self tapping screw - zinc
22 mm Wall Plugs
Cable clips
LCD reader removal tool
This product is not suitable for retail sale. All warranties are invalid if this product is not installed by a competent person.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to operate the equipment.
Page 

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 5
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:8bbf0b6a-1308-49c4-a266-0584116689c1
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2009:08:13 11:37:21+01:00
Metadata Date                   : 2009:08:13 11:38:02+01:00
Modify Date                     : 2009:08:13 11:38:02+01:00
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 9944 bytes, use -b option to extract)
Instance ID                     : uuid:7c51527b-3f5c-4158-a5f2-242964f5fe96
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:5b4cbd2d-76d1-11de-a33b-d4e8e5d8b76f
Derived From Instance ID        : 5b4cbd2c-76d1-11de-a33b-d4e8e5d8b76f
Derived From Document ID        : adobe:docid:indd:7fb7d9ac-954a-11dd-a06f-e1d42d55bea3
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 300.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Document ID  : adobe:docid:photoshop:3c983208-4eb1-11de-9e50-d9dc608d3779, uuid:42150805-3d83-491c-aa89-012e226b5b72, uuid:f4e612e6-2a50-4709-8b0d-8e46303db76a, uuid:5486B2E1E051DE118183EC524687FBF5, uuid:ba4656aa-3d5c-4c16-8aa2-eee89a1c50c8, uuid:8AA8E00AD99CDC1194088FCA155C3878
Manifest Reference Instance ID  : uuid:042f6d6c-e0da-42c3-9ee4-dceaa8cfdf21, uuid:5826d439-6169-43a3-a4eb-7efc6be51979, uuid:aeadde7f-13a3-4fea-82b6-904946c6b105
Format                          : application/pdf
Title                           : INSTRUCTION - PROXIMITY LCD reader
Tagged PDF                      : Yes
Creator                         : Adobe InDesign CS2 (4.0.5)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: USE380127

Navigation menu