Paxton Access 921130 Paxlock US User Manual

Paxton Access Ltd Paxlock US

User Manual

Paxtonins-40213-USPaxlock US
1x 2 x 2X 312*34568910151617 1819*720 212211121314???????????????Tools ListWhat’s in the box1) Front handle2) Lock Cylinder *3) Paxlock front housing4) Motor adjustment plate5) Motor6) 2-3/8” Latch 7) Latch screws x 2 8) Motor backplate9) Backplate/Rose assembly10) Paxlock rear housing11) 4 x AA Alkaline batteries12) Rear battery cover13) Rear handle cover14) Rear Handle15) Small mounting screws x 216) Long mounting screws x 317) Battery cover key18) Handle removal pin19) Keys x 2 *20) Handle washers x 221) Strike plate22) Strike plate screws x 2KnifeAdhesive tapePencilTape measure* Not for SFICPower DrillDrill bits (1”, 5/16”, 5/8”, 1/8”)Crosshead screwdriverChisel 1”
2122-3/8” (60mm) backset5/16” (8mm)5/16” (8mm)5/16” (8mm) 5/16” (8mm)2-1/8” (54mm)5/16” (8mm)5/8” (16mm)31” (25mm) Width3-1/4” (82mm) Depthx 2 x 2X 312*34568910151617 1819*720 212211121314Step 1: Marking outTape template to door, mark holes then remove template for drilling. Step 2: DrillingTo ensure accuracy you should drill holes from both sides of the door towards the center. This avoids the risk of damaging the door face when the drill breaks through.Make sure to include pilot holes either side of the central hole to ensure ush tting of the motor plates. Step 3: Marking out and chiseling for latchTo install the latch; drill a 1” (25mm) hole, slide in the latch, then draw around the faceplate.Remove the latch and score the outline with a knife to avoid splitting the wood when chiselling.
3465Step 6: Inserting the motorPass the motor through the central hole within the door, making sure to pass the motor lead through the hole rst. Step 5: Fitting the strike plateClose the door to mark the horizontal line of the strike plate.Measure one half of door thickness from door stop to mark vertical center line of the strike. Drill 1” (25.4mm) hole, 1/2” (12.7mm) deep at intersection of horizontal and vertical center lines. Cut out jamb 3/32” (2.4mm) deep or until the strike is ush with jamb. Tighten the strike plate screws securely. Step 4: Fitting the door latchAttach the latch using the screws provided.
4897- 1-3/4” (45mm)- 2” (50mm) Step 8: Ensuring the latch engagesMake sure the tail of the latch is engaging with the motor retractor correctly as illustrated. Step 7: Rotating the motor adjustment plateTo ensure that the motor adjustment plate is at the correct distance, rotate until it sits ush with the door and the motor has engaged properly.Please refer to the diagram for the correct position of the plate for each door thickness. Step 9: Fitting the front housingLine up front housing and ensure the body is ush to the door. *PaxLock US is set up for RH doors by default – please see page 8 for LH operation.
5131415101112Step 10: Fitting the rear backplate assemblyFeed the motor cable through the hole in the motor back plate. Step 11: Fitting the rear housing and motor wiringFeed both the cables through the rear housing cutout and t the lower long mounting screws. Step 12: Fitting the rear lock assembly and wiringFit top, long mounting screws and 2 lower short screws.
6131415101112Step 10: Fitting the batteriesStep 11: Securing the rear cover Step 12: Fitting the cover plate and handle
7Optional step: Contact switch Optional step: Inserting the handle washersHandle feel can be tightened with the use of the included washers. Optional step: Handle orientation for LH doorTo congure for LH door operation, remove the front and rear handles using the handle removal pin. Unscrew the 4 screws securing the rose to the front/rear housings, rotate 180 degrees and screw back together. Ret the handles, and push home until the axle engagement clicks.
8≤ 200x1x1≤ 1000Net2 Pro/Net2 Lite: http://paxton.info/1438 Software installation0 m3m15m20m30m50ft65ft100ft10ft0 ftWireless Signal Range
9124563Enrolling a PaxLock14232143
1014232143PaxLock reset Battery replacement
1110,000250641020050 ft3,5840 °C (-32 °F)IPX46” 81/2” 3”MinWidth HeightMaxTypDepthMin MaxSpecicationsNoNo20,000 operations 30,000 operations+55 °C (+131°F)4 x AA AlkalineEnvironment Battery typeTypical Battery lifeOperating temperatureExternal UseMoisture resistanceVandal resistanceDimensionsTotal outside dimensions (includes handle clearance)FeaturesMaximum number of users/tokensAccess LevelsTime zonesDoor unlock timeRecommended number of Paxlock’s per Net2Air bridgeNet2Air bridge per systemNet2Air wireless rangeEvents stored1 sec 60 secsUL has only evaluated the Operating temperature specication
12+44 (0)1273 811011paxton.supportsupport@paxton.co.uk+44 (0)1273 811011paxton.supportsupport@paxton.co.uk+1(800) 672-7298usapaxton.supportsupportUS@paxton-access.com+1(800) 672-7298usapaxton.supportsupportUS@paxton-access.com+49 (0) 251 2080 6900paxton.gmbh.supportsupport@paxton-gmbh.de+31 (0)76 3333 999paxton.benelux.supportsupport@paxton-benelux.com+31 (0)76 3333 999paxton.benelux.supportsupport@paxton-benelux.com+31 (0)76 3333 999paxton.benelux.supportsupport@paxton-benelux.com+33 (0)157 329356support@paxtonaccess.fr +27 (0) 272 14276691support@paxtonaccess.co.za+44 (0)1273 811011paxton.supportpaxton.supportpaxton.supportsupport@paxton.co.uk
13The declaration of conformity is available on request. Contact details are provided at: http://paxton.info/596These products are not suitable for retail sale. All warranties are invalid if these products are not installed by a competent person. North America:- Product Compliance and limitationsThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The Paxlock US has been designed and complies with the safety requirements for portable (<20cm) RF exposure in ac-cordance with FCC rule part 2.1093 and KDB 447498 D01 as demonstrated in the RF exposure analysis. Installers must ensure that this device must not be co-located or operated in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.FCC ComplianceIC ComplianceTo comply as a UL listed installation, the following conditions must apply:-• Server based functions (Antipassback, Time and Attendance, etc) have not been evaluated by UL and cannot be used for UL 294 installations.• Where an equivalent cable / wire is used it must be ‘ UL Listed ‘All interconnecting devices must be UL Listed.• The use of Wiegand readers and the conguration software has not been evaluated by ‘UL’• Door contact connections are limited to a maximum of 30m.• IP rating not veried by UL.• Indoor use onlyUL listed to the following standards: ANSI/UL 10C compliant (20 min re doors), CAN/ULC S104 compliant (20 min re doors), UL 294 compliant, CSA C22.2 NO. 205-12 compliantWiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The Paxlock US has been designed and complies with the safety requirements for RF exposure in accordance with RSS-102 as demonstrated in the RF exposure analysis.
14
1.0.0Made in the UK© Paxton Ltd 22/10/2014

Navigation menu