Paxton Access Z99MU10 Proximity Mullion Reader User Manual INSTRUCTION Mullion PROXIMITY reader UL
Paxton Access Ltd Proximity Mullion Reader INSTRUCTION Mullion PROXIMITY reader UL
User Manual
05/20/2010 Paxton Ins-40015-US Mullion PROXIMITY reader - UL Technical Support 1.800.672.PAXT Technical help is available: support@paxton-access.com Monday - Friday from 02:00 AM - 8:00 PM (EST) Saturday from 04:00 AM - 08:00 AM (EST) Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/ Suitability Security sensitive doors Mounted on metal surface Wet environments Readers mounted together 12 inches between readers Fitting This reader is designed to read EM4100 tokens. It will provide Clock and Data output for Paxton (Net2 / Switch2). PAGE Options Part number Description 353-110-US Mullion PROXIMITY reader +V out Red Power Power Relay 1 Relay 1 Relay 2 Relay 2 00v Inputs Contact Contact 5v 12V 12v OK OK PSU PSU Tamper Tamper Exit Exit Tx Tx Rx Rx Blue Clock/D Alarm PowerAlarm Power Door relay Yellow Data/D0 Door relay Card reader or keypad Card reader or keypad Control unit Green LED Green 0V 0v Exit Exit PSU PSU SSwitch2 witch Amber LED Orange N.O. N.O. Com Com 00v Red2V 12V Red LED Brown Com Com Alarm Output Alarm Output Inputs CAUTION: for 12v d.c. readers only. For correct connection of old 5v readers, refer to instructions. 24898 00000 Red LED Brown Serial number 241821 Orange Orange Net2 control unit N.O. N.O. Tamper Tamper Contact Contact Relay22 Relay White/Orange White/Orange3 Relay Relay11 Green Green 0V 0v N.C. N.C. NetwoNetwork rk CA T5 cacable ble codcoding ing CAT5 White/Green White/Green 1 Amber LED Orange Green LED Green Test ID: 012345678901 z-1440 Screen or from Screen orspare sparecores cores network cable from network cable 12V +12v N.C. N.C. Keypad 1 Keypad 1 Clock Orange Clock/D1 Blue 0V out Black/White Data/D0 Yellow Media Detect Mauve Load Brown Media Detect Mauve BlueClock/D1 Data Yellow Reader 2 Net2 Reader 1 Data/D0 Yellow Reader 2 Keypad 2 Reader 1 Green LED Green 0V out Black/White Keypad 2 outdc Red+V 12v Red LED Brown Amber LED Orange Load Brown Data Yellow Orange Clock Wiring Bell Bell 2V 12v Switch2 control unit (not evaluated by UL) 0V 0v N.C. N.C. N.O. N.O. COM Com Mauve Media Detect Black 0V CAUTION: For 2Vd.c. CAUTION: For 12V d.c. readers readers only. For correct only. For corr ect connection of old connection of old readers, readers, refer referto toinstructions instructions.. Inputs Exit Exit Inputs Contact Contact Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the authorities having jurisdiction. All interconnecting devices must be UL Listed. Cable extensions Cable Specification Use Max length Type Reader 100 yds 10 core, shielded - Beldon 9540, Alpha 1298C (22AWG) or equivalent NOTE: Where selected, any equivalent cabling / wire must be ‘ UL Listed ‘ PAGE Fitting Kit Option Part number Mullion Fitting Kit fk1-085 Description 5 off - Cable clips 3 off - No6 x 3/4in pozi round woodscrew - zinc 3 off - Wall plugs 22mm 1 off - 8mm x 3mm small pozi pan self tapping screw - zinc Unit installation / test When choosing a location for the reader, ensure that it is at least 12 inches from other readers. This will include readers mounted on the other side of the same wall as the radio signal will cause interference and reduce the read range. The reader should not be used on metal surfaces as the reflected signal will also reduce the read range. Standard Unit - Drill a hole in the surface for the rear data cable. Secure the unit to the surface with three screws as per fitting diagram on page 1. Suitable screws and fixings are provided for fitting the unit to a wall. Ensure the data cable has free access at the rear. A choice of black and white covers are also provided. Hook the required cover over the top of the reader, press home at the bottom and secure with the single fixing screw. The reader will beep and all the LED’s should display after powering on the control unit. Presenting a user card to the reader will cause the LED’s to briefly change to a single Green or Red LED. Check the following FAQs section for assistance if any problems are encountered. Maintenance Following the completed installation of this equipment, no further maintenance or testing is required. It is advisable to ensure that any third party backup power supplies or recovery procedures are checked regularly to ensure that the operation of the Paxton Access system is not compromised. FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. PAGE Technical Help Here is the list of topics about this product that receive the most technical support inquiries. We list them here to help you speed up the installation and trouble shooting process. 1 - Readers/Keypads not working. Q- Software settings - Confirm that the settings of the reader or keypad are correct. Q- Connections - Check the wiring and integrity of the connectors. If possible, test this reader on the other port. Q- Extended cable - Belden 9540 should be used up to a maximum of 100yds. Twisted pair alarm cable should Q not be used. To confirm that an extended reader cable is not at fault, wire the reader directly to the port. Q- Supply voltage - Confirm that the voltage is within specification. (see table) Q- User token - Confirm that the user token used for testing is OK by presenting it to a known working reader. Q- Interference - Confirm whether the reader works when tested ‘in hand’ and not mounted on the wall. Q PROXIMITY readers should not be mounted back to back or close to other RF devices. 2 - Readers / Keypads - Extending cable. QOnly Belden CR9538 / 9540 can be used for cable extensions. CR9538 8 core for up to 25yds, CR9540 10 core Qfor 25-100yds (maximum). With CR9540, the two additional cores should be used to double up the power. 3 - Net2 - Using a door reader as a desktop reader. QWhen there is no desktop reader on site it is possible to configure a door reader to operate as a desktop reader: Q1 - Select the doors menu in the left hand Net2 pane. Q2 - Click on the door you wish to change the reader to act as a desktop reader. Q3 - Under the relevant reader tab, change the reader operating mode to ‘Desktop Reader’. Q4 - The PC displays ‘Would you like to accept desktop reader events from this reader at the PC?’ ; click ‘Yes’ QNow when you present a blank or existing token to that reader it will act in the same way as a USB desktop Qreader, enabling you to add new tokens or edit existing ones. NOTE:QRemember to return the operating mode to the original setting once the cards have been read Qor users will not be able to gain access through the reader. QKP Reader - Ensure that Keypad type is set to ‘None’, otherwise the Desktop reader option will not be available. 4 - Net2. Two readers into one reader port. QTwo readers can be wired in parallel. - Color for Color. This can be useful in situations such as a barrier where Qdual height readers are required; one for cars, one for trucks. 5 - Net2. What to do if a user has no access - Check the reader LED’s when a card is shown. QQQQQ Q- No LED’s - the reader has no power. No change in display - try the card on a known working reader. If there is still no response, replace the card. Green LED flashing when a card is presented; check relay 1 LED to check for activity and also the lock wiring. Red LED is flashing when a card is presented; check the validity of the user at the PC. Check user’s access level and ensure they should have access by clicking on Current Validity. Check the ‘Valid Until’ date and confirm this has not expired. Reinstate the ACU from the doors screen. Select the ACU’s you wish to reinstate and then click OK. Specifications Environment Operating temperatures - all items Waterproof Min Max -35 °C ( -31 °F ) +66 °C ( + 151 °F ) IPX7 Outdoor Use 10 feet Cable length Electrical Min Max 12V DC Voltage 130 mA Current 125 kHz Carrier frequency 600 µs Clock and data bit period Dimensions Read Range Depth Width Height 1 3/4 inch 4 inch Token Keyfob Hands Free Token 3 inch 2 inch 4 feet 3/4 inch PAGE
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Count : 4 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:d3b40d59-9006-4ae6-97ea-a8bc8b9b331d Producer : Adobe PDF Library 7.0 Trapped : False Create Date : 2010:05:20 11:23:23+01:00 Metadata Date : 2010:05:20 11:24:00+01:00 Modify Date : 2010:05:20 11:24:00+01:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 6477 bytes, use -b option to extract) Instance ID : uuid:7c7ea822-4f7f-43d1-b327-8796f2dd1e9c Rendition Class : proof:pdf Document ID : adobe:docid:indd:6eda1fef-52c9-11df-a4e3-c2731754c4fc Derived From Instance ID : c0ed9629-26b5-11df-8392-badbe73b6fd3 Derived From Document ID : adobe:docid:indd:72fb475d-0cc1-11de-86e6-b4537f82d3e1 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 600.00, 72.00 Manifest Placed Y Resolution : 72.00, 600.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches Manifest Reference Instance ID : uuid:a27c06a5-0165-4819-8b7c-c5a8e9794cd2, uuid:207d20d3-83b8-4093-88cb-c1238db5de76 Manifest Reference Document ID : uuid:C18CBA7D2100DF11AE179FBCC0B84ED9, adobe:docid:photoshop:c0876e9a-64fb-11db-8a3e-971789a20d84, uuid:1d686997-20a0-4ddc-851b-cce15bb5b5da Format : application/pdf Title : INSTRUCTION - Mullion PROXIMITY reader - UL Tagged PDF : Yes Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools