Canon Mx490 Series Online Manual 1003107 1000317360 MSDS

2016-09-04

: Pdf 1000317360-Msds 1000317360-MSDS B4 unilog

Open the PDF directly: View PDF .
Page Count: 24

5535A Series QSIII 05/27/15

________________________________________________________________________________________________________

Page 1of 2

Safety Data Sheet

provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither

the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group: 26-4549-7 Version Number: 5.00

Issue Date: 05/27/15 Supercedes Date: 08/07/14

Product identifier

5535A Series QSIII

ID Number(s):

80-6112-3194-7, 80-6112-3195-4, 80-6112-3196-2, 80-6112-3197-0, 80-6112-3198-8, 80-6112-3199-6, 80-6112-3200-2, 80-6112-

3201-0, 80-6112-3202-8, 80-6112-3203-6, 80-6112-3204-4, 80-6112-3205-1, 80-6112-3206-9, 80-6112-6734-7, 80-6114-4337-7

Recommended use

Electrical

Supplier's details

MANUFACTURER: 3M

DIVISION: Electrical Markets Division

ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA

Telephone: 1-888-3M HELPS (1-888-364-3577)

Emergency telephone number

1-800-364-3577 or (651) 737-6501 (24 hours)

This product is a kit or a multipart product which consists of multiple, independently packaged components. A Safety Data

Sheet (SDS), Article Information Sheet (AIS), or Article Information Letter (AIL) for each of these components is included.

Please do not separate the component documents from this cover page. The document numbers for components of this

product are:

06-4861-8, 11-4628-1, 34-7684-3

DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF

TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of

use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely

within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a

particular purpose and suitable for user's method of use or application.

3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may

have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.

In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M

5535A Series QSIII 05/27/15

________________________________________________________________________________________________________

Page 2of 2

3M USA SDSs are available at www.3M.com

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 1 of 8

Safety Data Sheet

allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from

3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group: 06-4861-8 Version Number: 11.00

Issue Date: 03/19/14 Supercedes Date: 03/21/13

SECTION 1: Identification

1.1. Product identifier

P55/R Lubricant, Red

Product Identification Numbers

ID Number UPC ID Number UPC

78-8096-4318-8 78-8126-9891-4

80-6116-0479-6

1.2. Recommended use and restrictions on use

Recommended use

Electrical, ELECTRICAL LUBRICATING GREASE

1.3. Supplier’s details

MANUFACTURER: 3M

DIVISION: Electrical Markets Division

ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA

Telephone: 1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or (651) 737-6501 (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements

Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 2 of 8

Precautionary Statements

Disposal:

Dispose of contents/container in accordance with applicable local/regional/national/international regulations.

2.3. Hazards not otherwise classified

None.

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt

1,1,2,3,3,3-HEXAFLUORO-1-PROPENE, OXIDIZED,

POLYMD. 69991-67-9 95 - 98

SYNTHETIC AMORPHOUS SILICA, FUMED,

CRYSTALLINE FREE 112945-52-5 <= 5

C.I. PIGMENT RED 170 2786-76-7 <= 0.05

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you are concerned, get medical advice.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get

medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable.

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

Substance Condition

Carbonyl Fluoride During Combustion

Carbon monoxide During Combustion

Carbon dioxide During Combustion

Hydrogen Fluoride During Combustion

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 3 of 8

Oxides of Nitrogen During Combustion

5.3. Special protective actions for fire-fighters

No unusual fire or explosion hazards are anticipated. When fire fighting conditions are severe and total thermal

decomposition of the product is possible, wear full protective clothing, including helmet, self-contained, positive pressure or

pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective

covering for exposed areas of the head.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Ventilate the area with fresh air.

6.2. Environmental precautions

Avoid release to the environment.

6.3. Methods and material for containment and cleaning up

Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic

absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not

remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed

container approved for transportation by appropriate authorities. Clean up residue with an appropriate solvent selected by a

qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and

SDS. Seal the container. Dispose of collected material as soon as possible.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Keep away from reactive metals (eg. Aluminum, zinc etc.) to avoid the formation of

hydrogen gas that could create an explosion hazard.

7.2. Conditions for safe storage including any incompatibilities

Store away from acids. Store away from strong bases.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

No occupational exposure limit values exist for any of the components listed in Section 3 of this SDS.

8.2. Exposure controls

8.2.1. Engineering controls

Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure

Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.

8.2.2. Personal protective equipment (PPE)

Eye/face protection

None required.

Skin/hand protection

No chemical protective gloves are required.

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 4 of 8

Respiratory protection

None required.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties

General Physical Form: Liquid

Specific Physical Form: Paste

Odor, Color, Grade: ODORLESS, RED COLOR,GREASE

Odor threshold Not Applicable

pH Not Applicable

Melting point Not Applicable

Boiling Point 270 ºC [Details: MITS data (per supplier info)]

Flash Point Flash point > 93 °C (200 °F)

Evaporation rate No Data Available

Flammability (solid, gas) Not Applicable

Flammable Limits(LEL) Not Applicable

Flammable Limits(UEL) Not Applicable

Vapor Pressure <=0.01 mmHg

Vapor Density No Data Available

Density No Data Available

Specific Gravity Approximately 1.99 Units not avail. or not appl. [Ref Std:

WATER=1]

Solubility in Water Nil

Solubility-non-water Not Applicable

Partition coefficient: n-octanol/ water No Data Available

Decomposition temperature Not Applicable

Viscosity No Data Available

Average particle size No Data Available

Bulk density No Data Available

Hazardous Air Pollutants No Data Available

Molecular weight No Data Available

Volatile Organic Compounds No Data Available

Percent volatile 0.00 %

Softening point No Data Available

VOC Less H2O & Exempt Solvents No Data Available

SECTION 10: Stability and reactivity

10.1. Reactivity

This material may be reactive with certain agents under certain conditions -see the remaining headings in this section.

10.2. Chemical stability

Stable.

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 5 of 8

10.3. Possibility of hazardous reactions

Hazardous polymerization will not occur.

10.4. Conditions to avoid

Not determined

10.5. Incompatible materials

Strong acids

Strong bases

Reactive metals

No Data Available

10.6. Hazardous decomposition products

Substance Condition

None known.

Refer to section 5.2 for hazardous decomposition products during combustion.

Extreme heat arising from situations such as misuse or equipment failure can generate hydrogen fluoride as a decomposition

product.

SECTION 11: Toxicological information

The information below may not be consistent with the material classification in Section 2 if specific ingredient

classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be

reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be

present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be

relevant to the material as a whole.

11.1. Information on Toxicological effects

Signs and Symptoms of Exposure

Based on test data and/or information on the components, this material may produce the following health effects:

Inhalation:

No health effects are expected.

Skin Contact:

Contact with the skin during product use is not expected to result in significant irritation.

Eye Contact:

Contact with the eyes during product use is not expected to result in significant irritation.

Ingestion:

No health effects are expected.

Toxicological Data

If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or

the data are not sufficient for classification.

Acute Toxicity

Name Route Species Value

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 6 of 8

Overall product Ingestion No data available; calculated ATE > 5,000 mg/kg

SYNTHETIC AMORPHOUS SILICA, FUMED,

CRYSTALLINE FREE Dermal Rabbit LD50 > 5,000 mg/kg

SYNTHETIC AMORPHOUS SILICA, FUMED,

CRYSTALLINE FREE Inhalation-

Dust/Mist

(4 hours)

Rat LC50 > 0.691 mg/l

SYNTHETIC AMORPHOUS SILICA, FUMED,

CRYSTALLINE FREE Ingestion Rat LD50 > 5,110 mg/kg

ATE = acute toxicity estimate

Skin Corrosion/Irritation

Name Species Value

SYNTHETIC AMORPHOUS SILICA, FUMED, CRYSTALLINE FREE Rabbit No significant irritation

Serious Eye Damage/Irritation

Name Species Value

SYNTHETIC AMORPHOUS SILICA, FUMED, CRYSTALLINE FREE Rabbit No significant irritation

Skin Sensitization

Name Species Value

SYNTHETIC AMORPHOUS SILICA, FUMED, CRYSTALLINE FREE Human

and

animal

Not sensitizing

Respiratory Sensitization

Name Species Value

Germ Cell Mutagenicity

Name Route Value

SYNTHETIC AMORPHOUS SILICA, FUMED, CRYSTALLINE FREE In Vitro Not mutagenic

Carcinogenicity

Name Route Species Value

SYNTHETIC AMORPHOUS SILICA, FUMED, CRYSTALLINE

FREE Not

Specified Mouse Some positive data exist, but the data are not

sufficient for classification

Reproductive Toxicity

Reproductive and/or Developmental Effects

Name Route Value Species Test Result Exposure

Duration

SYNTHETIC AMORPHOUS SILICA,

FUMED, CRYSTALLINE FREE Ingestion Not toxic to female reproduction Rat NOAEL 509

mg/kg/day 1 generation

SYNTHETIC AMORPHOUS SILICA,

FUMED, CRYSTALLINE FREE Ingestion Not toxic to male reproduction Rat NOAEL 497

mg/kg/day 1 generation

SYNTHETIC AMORPHOUS SILICA,

FUMED, CRYSTALLINE FREE Ingestion Not toxic to development Rat NOAEL

1,350

mg/kg/day

during

organogenesi

Target Organ(s)

Specific Target Organ Toxicity -single exposure

Name Route Target Organ(s) Value Species Test Result Exposure

Duration

Specific Target Organ Toxicity -repeated exposure

Name Route Target Organ(s) Value Species Test Result Exposure

Duration

SYNTHETIC

AMORPHOUS SILICA, Inhalation respiratory system |

silicosis All data are negative Human NOAEL Not

available occupational

exposure

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 7 of 8

FUMED, CRYSTALLINE

FREE

Aspiration Hazard

Name Value

Please contact the address or phone number listed on the first page of the SDS for additional toxicological information

on this material and/or its components.

SECTION 12: Ecological information

Ecotoxicological information

Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material

and/or its components.

Chemical fate information

Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material

and/or its components.

SECTION 13: Disposal considerations

13.1. Disposal methods

Dispose of contents/ container in accordance with the local/regional/national/international regulations.

Prior to disposal, consult all applicable authorities and regulations to insure proper classification. Dispose of waste product in

a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste incineration facility. Proper

destruction may require the use of additional fuel during incineration processes. Combustion products will include halogen

acid (HCl/HF/HBr). Facility must be capable of handling halogenated materials. Empty and clean product containers may

be disposed as non-hazardous waste. Consult your specific regulations and service providers to determine available options

and requirements.

EPA Hazardous Waste Number (RCRA): Not regulated

SECTION 14: Transport Information

For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.

SECTION 15: Regulatory information

15.1. US Federal Regulations

Contact 3M for more information.

311/312 Hazard Categories:

Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -No Delayed Hazard -No

15.2. State Regulations

Contact 3M for more information.

15.3. Chemical Inventories

The components of this material are in compliance with the provisions of Australia National Industrial Chemical Notification

P55/R Lubricant, Red 03/19/14

__________________________________________________________________________________________

Page 8 of 8

and Assessment Scheme (NICNAS). Certain restrictions may apply. Contact the selling division for additional information.

The components of this product are in compliance with the new substance notification requirements of CEPA.

The components of this product are in compliance with the chemical notification requirements of TSCA.

Contact 3M for more information.

15.4. International Regulations

Contact 3M for more information.

This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.

SECTION 16: Other information

NFPA Hazard Classification

Health: 0 Flammability: 1 Instability: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address

the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar

emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include

the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

HMIS Hazard Classification

Health: 0 Flammability: 1 Physical Hazard: 0 Personal Protection: X -See PPE section.

Hazardous Material Identification System (HMIS® III) hazard ratings are designed to inform employees of chemical hazards

in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use

and are not intended for use in emergency situations. HMIS® III ratings are to be used with a fully implemented HMIS® III

program. HMIS® is a registered mark of the American Coatings Association (ACA).

Document Group: 06-4861-8 Version Number: 11.00

Issue Date: 03/19/14 Supercedes Date: 03/21/13

DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES

NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR

USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable

for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product,

some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to

determine whether it is fit for a particular purpose and suitable for user's method of use or application.

3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer

may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness

or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available

directly from 3M

3M USA SDSs are available at www.3M.com

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 1 of 10

Safety Data Sheet

allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from

3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group: 11-4628-1 Version Number: 34.02

Issue Date: 04/24/15 Supercedes Date: 10/20/14

SECTION 1: Identification

1.1. Product identifier

3M™Cable Preparation Kit CC-3 (Bag)

Product Identification Numbers

78-8018-9838-4, 80-6105-9300-8, 80-6116-0612-2

1.2. Recommended use and restrictions on use

Recommended use

Electrical, Solvent soaked pads for cleaning cable.

1.3. Supplier’s details

MANUFACTURER: 3M

DIVISION: Electrical Markets Division

ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA

Telephone: 1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or (651) 737-6501 (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Flammable Liquid: Category 4.

Skin Corrosion/Irritation: Category 2.

Skin Sensitizer: Category 1.

Specific Target Organ Toxicity (central nervous system): Category 3.

2.2. Label elements

Signal word

Warning

Symbols

Exclamation mark |

Pictograms

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 2 of 10

Hazard Statements

Combustible liquid.

Causes skin irritation.

May cause an allergic skin reaction.

May cause drowsiness or dizziness.

Precautionary Statements

Prevention:

Keep away from heat/sparks/open flames/hot surfaces. -No smoking.

Avoid breathing dust/fume/gas/mist/vapors/spray.

Use only outdoors or in a well-ventilated area.

Wear protective gloves.

Wash thoroughly after handling.

Contaminated work clothing must not be allowed out of the workplace.

Response:

IF INHALED: Remove person to fresh air and keep comfortable for breathing.

IF ON SKIN: Wash with plenty of soap and water.

If skin irritation or rash occurs: Get medical advice/attention.

Take off contaminated clothing and wash it before reuse.

Call a POISON CENTER or doctor/physician if you feel unwell.

In case of fire: Use a fire fighting agent suitable for flammable liquids such as dry chemical or carbon dioxide to

extinguish.

Storage:

Store in a well-ventilated place. Keep container tightly closed.

Keep cool.

Store locked up.

Disposal:

Dispose of contents/container in accordance with applicable local/regional/national/international regulations.

2.3. Hazards not otherwise classified

None.

SECTION 3: Composition/information on ingredients

Ingredient C.A.S. No. % by Wt

Isoparaffinic Hydrocarbon 64742-48-9 50 - 70

Cotton pads None 25 - 40

D-LIMONENE 5989-27-5 5 - 20

SECTION 4: First aid measures

4.1. Description of first aid measures

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 3 of 10

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop,

get medical attention.

Eye Contact:

No need for first aid is anticipated.

If Swallowed:

Rinse mouth. If you feel unwell, get medical attention.

4.2. Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3. Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for flammable liquids such as dry chemical or carbon dioxide to extinguish.

5.2. Special hazards arising from the substance or mixture

Closed containers exposed to heat from fire may build pressure and explode.

5.3. Special protective actions for fire-fighters

Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and

prevent explosive rupture.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Evacuate area. Keep away from heat/sparks/open flames/hot surfaces. -No smoking. Use only non-sparking tools.

Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or

exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and

could cause flammable gases or vapors in the spill area to burn or explode. Refer to other sections of this SDS for

information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment.

6.2. Environmental precautions

Avoid release to the environment.

6.3. Methods and material for containment and cleaning up

Contain spill. Cover spill area with a fire-extinguishing foam. An appropriate aqueous film forming foam (AFFF) is

recommended. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard.

Collect as much of the spilled material as possible using non-sparking tools. Place in a metal container approved for

transportation by appropriate authorities. Clean up residue with an appropriate solvent selected by a qualified and authorized

person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the

container. Dispose of collected material as soon as possible.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 4 of 10

For industrial or professional use only. Keep away from heat/sparks/open flames/hot surfaces. -No smoking. Avoid

breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when

using this product. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the

workplace. Avoid release to the environment. Wash contaminated clothing before reuse. Avoid contact with oxidizing

agents (eg. chlorine, chromic acid etc.)

7.2. Conditions for safe storage including any incompatibilities

Store in a well-ventilated place. Keep container tightly closed. Keep cool. Protect from sunlight. Store away from heat.

Store away from acids. Store away from oxidizing agents.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available

for the component.

Ingredient C.A.S. No. Agency Limit type Additional Comments

Isoparaffinic Hydrocarbon 64742-48-9 Manufacturer

determined TWA:100 ppm

ACGIH : American Conference of Governmental Industrial Hygienists

AIHA : American Industrial Hygiene Association

CMRG : Chemical Manufacturer's Recommended Guidelines

OSHA : United States Department of Labor -Occupational Safety and Health Administration

TWA: Time-Weighted-Average

STEL: Short Term Exposure Limit

CEIL: Ceiling

8.2. Exposure controls

8.2.1. Engineering controls

Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure

Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment.

8.2.2. Personal protective equipment (PPE)

Eye/face protection

Under normal use conditions, eye exposure is not expected to be significant enough to require eye protection.

Skin/hand protection

Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the

results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the

substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions.

Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective

clothing.

Gloves made from the following material(s) are recommended: Nitrile Rubber

Polymer laminate

If this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then

use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an

exposure assessment. The following protective clothing material(s) are recommended: Apron –Nitrile

Apron -polymer laminate

Respiratory protection

An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 5 of 10

a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator

type(s) to reduce inhalation exposure:

Half facepiece or full facepiece air-purifying respirator suitable for organic vapors

For questions about suitability for a specific application, consult with your respirator manufacturer.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties

General Physical Form: Solid (Lint-free cloths soaked with liquid)

Specific Physical Form: Cloth pads soaked in liquid in can or bag

Odor, Color, Grade: citrus-like odor

Odor threshold No Data Available

pH 7.0

Melting point No Data Available

Boiling Point 380 ºF -480 ºF

Flash Point 144 ºF [Test Method: Closed Cup]

Evaporation rate No Data Available

Flammability (solid, gas) Not Classified

Flammable Limits(LEL) No Data Available

Flammable Limits(UEL) No Data Available

Vapor Pressure < 1 mmHg [@ 25 ºC]

Vapor Density > 1 [Ref Std: AIR=1]

Specific Gravity 0.76 [Ref Std: WATER=1]

Solubility in Water Nil

Solubility-non-water No Data Available

Partition coefficient: n-octanol/ water No Data Available

Autoignition temperature No Data Available

Decomposition temperature No Data Available

Viscosity 1.5 centipoise

Volatile Organic Compounds Approximately 740 g/l

VOC Less H2O & Exempt Solvents 760 g/l

SECTION 10: Stability and reactivity

10.1. Reactivity

This material may be reactive with certain agents under certain conditions -see the remaining headings in this section.

10.2. Chemical stability

Stable.

10.3. Possibility of hazardous reactions

Hazardous polymerization will not occur.

10.4. Conditions to avoid

Sparks and/or flames

10.5. Incompatible materials

Strong oxidizing agents

10.6. Hazardous decomposition products

Substance Condition

Carbon monoxide Not Specified

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 6 of 10

Carbon dioxide Not Specified

SECTION 11: Toxicological information

The information below may not be consistent with the material classification in Section 2 if specific ingredient

classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be

reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be

present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be

relevant to the material as a whole.

11.1. Information on Toxicological effects

Signs and Symptoms of Exposure

Based on test data and/or information on the components, this material may produce the following health effects:

Inhalation:

Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose

and throat pain.

May cause additional health effects (see below).

Skin Contact:

Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, dryness, cracking, blistering, and pain.

Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching.

Eye Contact:

Contact with the eyes during product use is not expected to result in significant irritation.

Ingestion:

Physical Blockage: Signs/symptoms may include cramping, abdominal pain, and constipation.

Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.

Additional Health Effects:

Single exposure may cause target organ effects:

Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination,

nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness.

Toxicological Data

If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or

the data are not sufficient for classification.

Acute Toxicity

Name Route Species Value

Overall product Ingestion No data available; calculated ATE > 5,000 mg/kg

Isoparaffinic Hydrocarbon Inhalation-

Vapor LC50 estimated to be 20 -50 mg/l

Isoparaffinic Hydrocarbon Dermal Rabbit LD50 > 3,000 mg/kg

Isoparaffinic Hydrocarbon Ingestion Rat LD50 > 5,000 mg/kg

D-LIMONENE Inhalation-

Vapor (4

hours)

Mouse LC50 > 3.14 mg/l

D-LIMONENE Dermal Rabbit LD50 > 5,000 mg/kg

D-LIMONENE Ingestion Rat LD50 4,400 mg/kg

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 7 of 10

ATE = acute toxicity estimate

Skin Corrosion/Irritation

Name Species Value

Isoparaffinic Hydrocarbon Rabbit Irritant

D-LIMONENE Rabbit Mild irritant

Serious Eye Damage/Irritation

Name Species Value

Isoparaffinic Hydrocarbon Rabbit No significant irritation

D-LIMONENE Rabbit Mild irritant

Skin Sensitization

Name Species Value

Isoparaffinic Hydrocarbon Guinea

pig Not sensitizing

D-LIMONENE Mouse Sensitizing

Respiratory Sensitization

For the component/components, either no data are currently available or the data are not sufficient for classification.

Germ Cell Mutagenicity

Name Route Value

Isoparaffinic Hydrocarbon In vivo Not mutagenic

Isoparaffinic Hydrocarbon In Vitro Some positive data exist, but the data are not

sufficient for classification

D-LIMONENE In Vitro Not mutagenic

D-LIMONENE In vivo Not mutagenic

Carcinogenicity

Name Route Species Value

Isoparaffinic Hydrocarbon Dermal Mouse Some positive data exist, but the data are not

sufficient for classification

Isoparaffinic Hydrocarbon Inhalation Human

and

animal

Some positive data exist, but the data are not

sufficient for classification

D-LIMONENE Ingestion Rat Some positive data exist, but the data are not

sufficient for classification

Reproductive Toxicity

Reproductive and/or Developmental Effects

Name Route Value Species Test Result Exposure

Duration

Isoparaffinic Hydrocarbon Inhalation Not toxic to development Rat NOAEL 2.4

mg/l during

organogenesi

D-LIMONENE Ingestion Not toxic to male reproduction Rat NOAEL 150

mg/kg/day 103 weeks

D-LIMONENE Ingestion Some positive female reproductive data

exist, but the data are not sufficient for

classification

Rat NOAEL 750

mg/kg/day premating &

during

gestation

D-LIMONENE Ingestion Some positive developmental data exist,

but the data are not sufficient for

classification

Multiple

animal

species

NOAEL 591

mg/kg/day during

organogenesi

Target Organ(s)

Specific Target Organ Toxicity -single exposure

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 8 of 10

Name Route Target Organ(s) Value Species Test Result Exposure

Duration

Isoparaffinic Hydrocarbon Inhalation central nervous

system depression May cause drowsiness or

dizziness Human

and

animal

NOAEL Not

available

Isoparaffinic Hydrocarbon Inhalation respiratory irritation Some positive data exist, but the

data are not sufficient for

classification

NOAEL Not

available

Isoparaffinic Hydrocarbon Inhalation nervous system Some positive data exist, but the

data are not sufficient for

classification

Dog NOAEL 6.5

mg/l 4 hours

D-LIMONENE Ingestion nervous system Some positive data exist, but the

data are not sufficient for

classification

NOAEL Not

available

Specific Target Organ Toxicity -repeated exposure

Name Route Target Organ(s) Value Species Test Result Exposure

Duration

Isoparaffinic Hydrocarbon Inhalation nervous system Some positive data exist, but the

data are not sufficient for

classification

Rat LOAEL 4.6

mg/l 6 months

Isoparaffinic Hydrocarbon Inhalation kidney and/or

bladder Some positive data exist, but the

data are not sufficient for

classification

Rat LOAEL 1.9

mg/l 13 weeks

Isoparaffinic Hydrocarbon Inhalation respiratory system Some positive data exist, but the

data are not sufficient for

classification

Multiple

animal

species

NOAEL 0.6

mg/l 90 days

Isoparaffinic Hydrocarbon Inhalation bone, teeth, nails,

and/or hair | blood |

liver | muscles

All data are negative Rat NOAEL 5.6

mg/l 12 weeks

Isoparaffinic Hydrocarbon Inhalation heart All data are negative Multiple

animal

species

NOAEL 1.3

mg/l 90 days

D-LIMONENE Ingestion kidney and/or

bladder Some positive data exist, but the

data are not sufficient for

classification

Rat LOAEL 75

mg/kg/day 103 weeks

D-LIMONENE Ingestion liver Some positive data exist, but the

data are not sufficient for

classification

Mouse NOAEL

1,000

mg/kg/day

103 weeks

D-LIMONENE Ingestion heart | endocrine

system | bone, teeth,

nails, and/or hair |

hematopoietic

system | immune

system | muscles |

nervous system |

respiratory system

All data are negative Rat NOAEL 600

mg/kg/day 103 weeks

Aspiration Hazard

Name Value

Isoparaffinic Hydrocarbon Aspiration hazard

D-LIMONENE Aspiration hazard

Please contact the address or phone number listed on the first page of the SDS for additional toxicological information

on this material and/or its components.

SECTION 12: Ecological information

Ecotoxicological information

Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material

and/or its components.

Chemical fate information

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 9 of 10

Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material

and/or its components.

SECTION 13: Disposal considerations

13.1. Disposal methods

Dispose of contents/ container in accordance with the local/regional/national/international regulations.

Incinerate in a permitted waste incineration facility. Proper destruction may require the use of additional fuel during

incineration processes. As a disposal alternative, Dispose of waste product in a permitted industrial waste facility. Empty

drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations

classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes

unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the

available treatment and disposal facilities.

EPA Hazardous Waste Number (RCRA): Not regulated

SECTION 14: Transport Information

For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.

SECTION 15: Regulatory information

15.1. US Federal Regulations

Contact 3M for more information.

311/312 Hazard Categories:

Fire Hazard -Yes Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -Yes Delayed Hazard -No

15.2. State Regulations

Contact 3M for more information.

15.3. Chemical Inventories

The components of this material are in compliance with the provisions of Australia National Industrial Chemical Notification

and Assessment Scheme (NICNAS). Certain restrictions may apply. Contact the selling division for additional information.

The components of this product are in compliance with the new substance notification requirements of CEPA.

The components of this material are in compliance with the provisions of the Korean Toxic Chemical Control Law. Certain

restrictions may apply. Contact the selling division for additional information.

The components of this material are in compliance with the provisions of Philippines RA 6969 requirements. Certain

restrictions may apply. Contact the selling division for additional information.

The components of this product are in compliance with the chemical notification requirements of TSCA.

Contact 3M for more information.

15.4. International Regulations

Contact 3M for more information.

3M™Cable Preparation Kit CC-3 (Bag) 04/24/15

__________________________________________________________________________________________

Page 10 of 10

This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.

SECTION 16: Other information

NFPA Hazard Classification

Health: 2 Flammability: 2 Instability: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address

the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar

emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include

the toxic properties of combustion or decomposition products that are known to be generated in significant quantities.

HMIS Hazard Classification

Health: *2 Flammability: 2 Physical Hazard: 0 Personal Protection: B