DIA3ED2041102EN 1000336427 Catalog

2016-10-06

• Programmable controller
• Twido
• 05
• Twido programmable controller
  • Compact and modular base controllers
    • (1) Sink input: positive logic. Source input: negative logic.
    • (2) Within the consumption limit controlled by TwidoSoft software.
    • (3) The AS-Interface M3 profile supports analog profile 7.3 (7 slaves), but does not support anal...
    • (4) With maximum of 42 relay outputs (on base controller and I/O expansions).
    • (5) Dedicated c 24 V discrete inputs of the base controller and up/down counting with preset.
    • (6) The maximum values of the internal words and function blocks cannot be cumulated.
    • (7) Replace the p in the reference with T: source transistor outputs, U: sink transistor outputs.
• Twido programmable controller
  • Compact base controllers
  • TWD LCpA 10DRF
  • TWD LCpA 16DRF
  • TWD LCpA 24DRF
  • TWD LCAp 40DRF
    • (1) i.e.: a maximum of 88 I/O with screw terminal expansion modules, with a maximum of 32 relay o...
    • (2) i.e. a maximum of 152 I/O with screw terminal expansion modules. Maximum of 264 I/O with HE1...
    • (3) Built-in real-time clock.
• Twido programmable controller
  • Compact base controllers
    • 1 Two hinged connection terminal block covers for access to the terminals
    • 2 A hinged access door
    • 3 A mini-DIN type RS 485 serial port connector (allowing connection of the programming terminal)
    • 4 A slot (protected by a removable cover) for digital diagnostic/maintenance display module TWDX...
    • 5 A screw terminal block for c 24 V supply to the sensors and for connection of the input sensors
    • 6 A connector for I/O expansion modules TWDDpp, TWD App and TWDNOI10M3 (maximum of 4 modules o...
    • 7 A display block showing:
    • 8 A screw terminal block for connection of the output pre-actuators
    • 9 Two analog adjustment points (one point for 10 and 16 I/O models)
    • 10 An extension connector for the addition of a 2nd RS 232C/RS 485 serial port using adapter TWD ...
    • 11 A screw terminal block for connection of the a100...240 V mains or c19.2...30V power supply
    • 12 A connector (access through the bottom of the controller) for: - memory cartridge TWD XCP MFK3...
    • 13 An RJ45 connector (access through the bottom of the controller) for connection to the Ethernet...
• Twido programmable controller
  • Compact base controllers
  • (1) The first value corresponds to the maximum number of I/O (base controller and expansion modul...
  • (2) The maximum values cannot be cumulated.
  • (3) With 16 I/O base controllers TWD LCpA 16DRF and 24 I/O base controllers TWDLCpA24DRF.
• Characteristics (continued)
  • Twido programmable controller
    • Compact base controllers
      • (1) Compact base controllers TWD LCpA 10DRF/16DRF/24DRF have only one cartridge slot, therefore o...
      • (2) Built-in real-time clock cartridge for compact base controllers TWD LCAp 40DRF.
  • Twido programmable controller
    • Compact base controllers
    • TWD LCpA 10DRF/16DRF
    • TWD XCP MFK32/RTC
    • TWD NAC pppp
    • TWD XCP ODC
    • XBTN401
      • (1) 6000 instructions with memory extension cartridge TWD XCP MFK64.
      • (2) Base controller equipped with an integrated Ethernet link (RJ45 port).
      • (3) Other separate components, see page 46
      • (4) Connection via built-in port or via optional serial port on Twido programmable controllers.
      • (5) Without ground fault detection.
  • Twido programmable controller
    • Compact base controllers
    • (1)
    • (1)
    • (1)
    • (1) TWDLCAA ppDRF: a 100…240 V, TWDLCDA ppDRF: c 19.2…30 V.
    • (2) a 100…240 V supply only, identical to TWDLCAA ppDRF.
  • Twido programmable controller
    • Modular base controllers
    • TWD LMDA 20DTK/20DUK
    • TWD LMDA 20DRT
    • TWD LMDA 40DTK/40DUK
  • Twido programmable controller
    • Modular base controllers
      • 1 A hinged door
      • 2 An analog adjustment point
      • 3 A connector for connection of the built-in analog input
      • 4 A display block showing:
      • 5 A mini-DIN type RS 485 serial port connector (allowing connection of the programming terminal)
      • 6 Two slots (protected by a removable cover) for memory cartridge TWDXCPMFKpp and real-time clo...
      • 7 One (or more) HE 10 type connector(s) or screw terminal block for connection of the input senso...
      • 8 Screw terminals for connection of the c24 V mains power supply
      • 9 A connector for I/O expansion modules TWDDpp, TWDApp and TWDNOI10M3 (4 or 7 depending on mo...
  • Twido programmable controller
    • Modular base controllers
      • (1) Source output: positive logic, sink output: negative logic.
      • (2) The first value corresponds to the maximum number of I/O (base controller and expansion modul...
      • (3) The maximum values cannot be cumulated.
      • (4) Or with serial interface adapter TWD NAC pppp fitted in built-in display module TWDXCP ODM.
• Characteristics (continued)
  • Twido programmable controller
    • Modular base controllers
      • (1) Source output: positive logic, sink output: negative logic.
      • (2) 2A/a 240 V or 2A/c 30 V (with 1800 operations/hour max): - electrical life: minimum 100 000 o...
  • Twido programmable controller
    • Modular base controllers
    • TWD LMDA 20DTK/20DUK
    • TWD LMDA 20DRT
    • TWD XCP MFK pp
    • XBTN401
    • ABL7CEMpppp
      • (1) 6000 instructions with memory extension cartridge TWD XCP MFK64
      • (2) Connection by HE 10 type connector, allowing use of the Telefast pre-wired system (see page 58).
      • (3) Memory extension with base controllers TWD LMDA 20DRT/40DpK.
      • (4) Connection via built-in port or via optional serial port on Twido programmable controllers.
      • (5) These products do not conform to standard EN 61000-3-2.
      • (6) Compatible input voltage, not indicated on the product.
      • (7) Without ground fault detection.
  • Twido programmable controller
    • Modular base controllers
      • (1) Supply connection for sink inputs (positive logic).
      • (2) Supply connection for source inputs (negative logic).
  • Twido programmable controller
    • Discrete I/O modules
      • (1) Sink input: positive logic, source input: negative logic.
• Selection guide (continued)
  • Twido programmable controller
    • Discrete I/O modules
      • (1) Source output: positive logic, sink output: negative logic.
  • Twido programmable controller
    • Discrete I/O modules
      • 1 An extension connector for electrical connection to the previous module (1)
      • 2 One or two blocks for displaying the channels and module diagnostics
      • 3 One or two connection components of varying type, depending on the model:
      • 4 Latching mechanism for attachment to the previous module
        • (1) A connector on the right-hand side panel ensures continuity of the electrical link with the n...
  • Twido programmable controller
    • Discrete I/O modules
      • (1) Consumption values are indicated for all inputs/outputs at state0 or at state 1.
      • (2) Source output: positive logic, sink output: negative logic.
  • Twido programmable controller
    • Discrete I/O modules
    • TWD DDI 8DT
    • TWD DDO 16pK
      • (1) Module allowing use of the Telefast pre-wired system.
    • TWD DRA 16RT
    • TWD DDM 8DRT
• References (continued)
  • Twido programmable controller
    • Discrete I/O modules
      • (1) Cables strictly for applications other than use of Telefast sub-bases with Twido controllers....
  • Twido programmable controller
    • Discrete I/O modules
• Connections (continued)
  • Twido programmable controller
    • Discrete I/O modules
      • (1)
      • (2)
      • (1)
      • (2)
      • (1) Source input (negative logic)
      • (2) Sink input (positive logic).
• Connections (continued)
  • Twido programmable controller
    • Discrete I/O modules
• Connections (continued)
  • Twido programmable controller
    • Discrete I/O modules
      • (1) Sink output (negative logic)
      • (2) Source output (positive logic)
      • (1) Source input (negative logic)
      • (2) Sink input (positive logic)
      • (3) Sink output (negative logic)
      • (4) Source output (positive logic)
  • Twido programmable controller
    • Analog I/O modules
  • Twido programmable controller
    • Analog I/O modules
      • 1 An extension connector for electrical connection to the previous module(1)
      • 2 A block for displaying the channel and module diagnostics
      • 3 A removable screw terminal block for connection of the c24V external power supply, the sensor...
      • 4 A latching mechanism for attachment to the previous module
        • (1) A connector on the right-hand side panel ensures continuity of the electrical link with the n...
  • Twido programmable controller
    • Analog I/O modules
• Characteristics (continued)
  • Twido programmable controller
    • Analog I/O modules
  • Twido programmable controller
    • Analog I/O modules
    • TWD AMI 2HT
    • TWD ALM 3LT
  • Twido programmable controller
    • Analog I/O modules
    • (1) Analog current/voltage output peripheral.
• Connections (continued)
  • Twido programmable controller
    • Analog I/O modules
  • Twido programmable controller
    • Master module for AS-Interface cabling system
    • Sensors
      • 1 A display block comprising:
      • 2 A block for displaying the status of the addresses
      • 3 Two push buttons PB1 and PB2 for controlling the status of the slaves by selecting their addres...
      • 4 An extension connector for electrical connection to the previous module
      • 5 A connector (on the RH side) for I/O expansion modules TWDDpp and TWDApp (4 or 7 depending on...
      • 6 A latching mechanism for attachment to the previous module
      • 7 A power supply removable screw terminal block
    • The display block on the front panel of master module TWDNOI10M3 allows simplified local diagno...
    • Each AS-Interface module sensor/actuator is seen by the Twido programmable controller in the same...
  • Twido programmable controller
    • Master module for AS-Interface cabling system
      • (1) When analog and discrete modules are connected simultaneously to the network, the analog modu...
  • Twido programmable controller
    • Communication
    • Modbus network
      • 1 An RS485 serial port, with mini-DIN type connector, for connection to the programming terminal
      • 2 A slot for fitting a 2nd optional port (RS485/RS232) using TWD NACppp adapters
      • 1 An RS485 serial port, with mini-DIN type connector, for connection to the programming terminal
    • (1) With max. cable length: 200 m.
    • (2) With max. cable length: 10 m.
  • Twido programmable controller
    • Communication
    • TWD NCO1M
      • 1 An grounded, 3-way, c 24 V supply connector
      • 2 A PWR LED, indicating module power ON or OFF
      • 3 A 9-way SUB-D connector for connection to the CANopen bus
      • 4 An ground screw
      • 5 A connector for connection to the Twido controller or to another I/O expansion module
  • Twido programmable controller
    • Communication
    • 499 TWD 01100
      • 1 Five LEDs (SER ACT, STATUS, LINK, 100 MB, ETH ACT) indicating performances associated with the ...
      • 2 An RJ45 connector for connection of the power supply and communications to the RS 485 on the Tw...
      • 3 An RJ45 connector (accessed through the bottom of the module) for connection to the Ethernet TC...
      • 4 An grounding screw (accessed through the bottom of the module)
    • (1) Cable TWD XCA RJP03P, connected to port 1 on the Twido controller, forces configuration of th...
  • Twido programmable controller
    • Communication
      • 1 Remote programming PC
      • 2 Cable TSX PCX 1031 on serial port (Rx/Tx crossing to be made or use cable TSXPCX1130)
      • 3 Modem for transmitting/receiving data
      • 4 Telephone or radio link
      • 5 Twido compact or modular controller
      • 1 Programming PC
      • 6 Cable TSX PCX 1031 on RS485 serial port or cable TSXPCX3030 on USB port for Windows 2000 or XP
      • 7 Twido compact or modular controller
      • 1 Programming PC with integrated Bluetooth technology or Bluetooth gateway for PC, reference VW3 ...
      • 2 Pocket PC with TwidoAdjust software For optimum performance, use a Pocket PC with integrated Bl...
      • 3 Bluetooth gateway VW3 A8114
      • 4 Twido compact or modular controller
      • 1 Magelis compact display XBTN40p
      • 2 Cable XBTZ978 on serial port
      • 3 Cable for optional RS485 port, reference TWD XCA RJ0pp
      • 4 Twido modular controller
      • 5 Modbus hub LU9GC3
      • 6 Modbus tap link cable VW3 A8 306 Rpp
      • 7 Line end adapters VW3 A8 306 RC
      • 8 Modbus T-junctions VW3 A8 306 TFpp (with cables)
      • 9 Twido compact controller
      • 10 Devices: Altistart48 starters, Altivar28, Altivar31 variable speed drives, Modbus OTB I/O i...
  • Twido programmable controller
    • Communication
      • 1 Magelis compact display XBTN40p and cable XBTZ978 on serial port
      • 2 Twido compact controllers TWDLCpA 24DRF or TWDLCAp 40DRF or Twido modular controllers, versio...
      • 3 Twido TWD NCO1M CANopen bus master module
      • 4 CANopen FTB I/O splitter box r
      • 5 ATV 31 starter
      • 6 CANopen OTB I/O interface module r
      • 1 Magelis compact display XBTN40p and cable XBTZ978 on serial port
      • 2 Twido master or slave, 40 I/O compact base controller TWDLCAE 40DRF
      • 3 Premium automation platform (1)
      • 4 Twido slave, compact or modular base controller
      • 5 TwidoPort 499 TWD 01100 interface module
      • 6 ConneXium 499 NEH 104 10 hub or ConneXium 499 NES 251 00 switch
      • 7 Ethernet OTB I/O interface module r
      • 8 Web Factory Cast Gateway TSX ETG 1000 (2)
        • (1) Please see our “Premium automation platform” catalog, # MKTED204032EN.
        • (2) Please see our “Ethernet TCP/IP and the Web” catalog # MKTED204073EN.
  • Twido programmable controller
    • Communication
      • 1 Simple ASCII display
      • 2 Cable TSX PCX 1031 on serial port (Rx/Tx crossing to be made or use cable TSXPCX1130)
      • 3 Modem for transmitting/receiving data
      • 4 Telephone or radio link
      • 5 Twido compact or modular controller
      • 6 ASCII printer
      • 7 Standard RS485/RS232 cable on optional port
      • 1 Simple ASCII display
      • 2 Standard RS485 cable or cable TSXPCX1031 for RS232 conversion, on serial port
      • 3 Twido compact or modular controller
      • 4 Standard RS485/RS232 cable on optional link
      • 5 ASCII printer
        • (1) Connection is made either to the serial port, or to the optional port.
      • 1 Base controller
      • 2 RS485, 3-wire cable on serial port or on optional port
      • 3 Twido base controllers used as I/O extension or as local “reflex” controller
  • Twido programmable controller
    • Communication
    • TWD NOZ ppp
    • (1) Replace the pp in the reference with 02: 2 m, 05: 5 m, 12: 12 m, 40: 40 m and 80: 80 m.
    • (2) Cable TWD XCA RJP03P, connected to port 1 on the Twido controller, forces configuration of th...
    • (3) PC with TwidoSoft software installed and running under Windows 2000 or XP operating system only.
  • Twido programmable controller
    • Communication
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
      • 1 HE10 connector (20-way for ABE7E16ppppp, 26-way for ABE7B20ppppp)
      • 2 Fuse for the c24V supply circuit
      • 3 Rail mounting
      • 4 LED for channel indication (only on ABE7B20MPN22 and ABE7E16SPN22)
      • 5 c24V power supply terminal block
      • 6 Blade disconnector on c0V (only on ABE7B20MPN22 and ABE7E16SPN22)
      • 7 Legend holder cover: customer marking on outside and sub-base wiring scheme on inside, providin...
      • 8 Test point for Ø2.3mm plug
      • 9 Upper terminal block for connection of signals
      • 10 Lower terminal block for connection of commons
      • 11 Optional snap-on terminal block with 20 screw terminals
      • 1 HE10 connector, 20-way
      • 2 Fuse for the c24V supply circuit
      • 3 Rail mounting
      • 4 c24V power supply terminal block
      • 5 Test point for Ø2.3mm plug
      • 6 Upper terminal block for connection of signals
      • 7 Lower terminal block for connection of commons
      • 8 Optional snap-on terminal block with 20 screw terminals
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
• Compatibility
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
      • 1 Modular base controller with 26-way HE10 connectors. The modular sizes available are 20 or 40...
      • 2 Input and output modules with 20-way HE10 connectors. The modular sizes available are 16 or 32...
      • 3 Cable (ABFT26Bpp0) equipped with a 26-way HE10 connector at each end. This cable is available...
      • 4 Cable (ABFT20Epp0) equipped with a 20-way HE10 connector at each end. This cable is available...
      • 5 20channel sub-base (ABE7B20MPN2p or ABE7B20MR20) for modular base controllers.
      • 6 16channel sub-base (ABE7E16SPN22 or ABE7E16SRM20) for output extension modules.
      • 7 16channel sub-base (ABE7E16EPN20 or ABE7E16SPN20) for input or output extension modules.
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
• Characteristics (continued)
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
      • 1 Cables ABF T2ppppp c.s.a. 0.08 mm2 (AWG28)
• Curves (continued)
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
    • (1) DC12: control of resistive loads and of solid state loads isolated by optocoupler, L/R £ 1 ms.
    • (2) DC13: control of electromagnets, L/R £2 x (Ue x Ie) in ms, Ue: Rated operational voltage, I...
    • (3) AC12: control of resistive loads and of solid state loads isolated by optocoupler, cos j ³ 0.9.
    • (4) AC14: control of small electromagnetic loads £ 72 VA, make: cos j = 0.3, break: cos j = 0.3.
    • (5) AC15: control of electromagnetic loads > 72 VA, make: cos j = 0.7, break: cos j = 0.4.
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
• References (continued), dimensions
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
    • (1) ABE7BV20, ABE7BV20TB.
    • (1) ABE7BV20, ABE7BV20TB.
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
    • BJ1
    • BJ1
    • (1) Example of output connections. When connecting an inductive load, include a diode or a varistor.
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
    • BJ1
    • (1) Example of output connections. When connecting an inductive load, include a diode or a varistor.
      • BJ1
• Schemes (continued)
  • Connection interfaces
    • BJ1
    • BJ1
    • (1) Example of output connections. When connecting an inductive load, include a diode or a varistor.
• Schemes (continued)
  • Connection interfaces
    • Advantys, Telefast® pre-wired system for Twido
    • BJ1
    • (1) Example of output connections. When connecting an inductive load, include a diode or a varistor.
  • Twido programmable controller
    • TwidoSoft programming software
  • Twido programmable controller
    • TwidoSoft programming software
• Functions (continued)
  • Twido programmable controller
    • TwidoSoft programming software
• Functions (continued)
  • Twido programmable controller
    • TwidoSoft programming software
• Functions (continued)
  • Twido programmable controller
    • TwidoSoft programming software
  • Twido programmable controller
    • TwidoSoft programming software
      • (1) When the numbers of objects are not indicated, see characteristics pages 8 and 14.
• Characteristics (continued)
  • Twido programmable controller
    • TwidoSoft programming software
      • (1) When the numbers of objects are not indicated, see characteristics pages 8 and 14.
  • Twido programmable controller
    • TwidoSoft programming software
      • (1) Typical recommended configuration: 300 MHz processor, 128 Mb of RAM with 40Mb of available h...
      • (2) PC running under Windows 2000 or XP operating system only.
  • Twido programmable controller
    • TwidoAdjust software
    • Example of TwidoAdjust software screen
  • Twido programmable controller
    • TwidoAdjust software
    • VW3 A8114
      • (1) Connection schemes, see page 43.
  • Twido programmable controller
    • Product Reference Index
  • Twido programmable controller
    • Community regulations
    • Protective treatment of equipment
      • (1) “TC” treatment: all climate treatment.
      • (2) “TH” treatment: treatment for hot and humid environments.
    • The efficiency of Telemecanique
    • branded solutions
    • A worldwide presence
    • Simply Smart !