P RDF Version A.1

: Pdf 100190-Attachment 100190-Attachment 783166 Batch7 unilog

Open the PDF directly: View PDF .
Page Count: 36

Download
Open PDF In Browser	View PDF

RDF Series
Direct-Fired
Makeup Air Heater

IMPORTANT
1. Always include complete heater model and serial number so
that any specification change can be considered for parts shipment. It can save time and expense.
2. Specifications are subject to change without notice.
3. We reserve the right to substitute functional replacements.
4. Order either by Kit or Component Part No.

Replacement Parts Form RZ-NA P-RDF (Version A)
Obsoletes Form RGM 740 (Version A) and P-RDF

®

APPLIES TO:
Index by Page No.
Amplifier
Belts
Blowers
Burners
Cabinet Parts
Circuit Analyzer Board
Contactor
Dampers
Disconnect Switch
Drives
ECO Device
Electrical Compartment Illustration
Filter Sections
Filters
Firestat
Flame Sensor
Freezestat
Fuseholder and Fuses
Gas T rain Controls
Outside Air Inlet Hoods
Ignition System
Limit Controls
Maxitrol System Components
Mirror
Modulating Gas Controls
Motors (Blower)
Motors (Damper)
Potentiometer
Pressure Switches (Air)
Pressure Switches (Gas)
Rating Plate
Regulators
Relays
Remote Console
Roof Curbs
Serial No.
Sheaves
Starters
T emperature Sensor
T ransformer
Valves

13
23-32
22
16-16
33-36
4-5
6
17-18
21
23-32
4-5
3
35
35
4-5
14, 15
4-5
4-5
11-12
35
14-15
4-5
13
16
13-14
6-8
17-18
4, 6, 20
4-5
12
1
11
4
20
36
2
23-32
6-10
13
4-5
11-12

Rating Plate and Serial No.
REZNOR
MERCER, PA. USA 16137

ANSI Z83.18A-2001 DIRECT-FIRED INDUSTRIAL AIR HEATER
FOR INDUSTRIAL/COMMERCIAL USE ONLY
FOR EITHER INDOOR OR OUTDOOR INSTALLATION
MODEL
{
}
SERIAL #
A
GAS TYPE {
}
MOTOR HP {
B
VOLTAGE {
}
PHASE
{
D
MAX TOTAL INPUT AMPS FOR THE UNIT
{
WIRING DIAGRAM NUMBER: {
}
P

}

C
E
F

}
}

60 HZ

UNIT IS EQUIPPED FOR { G } SCFM AGAINST { H } IN WC ESP
WITH A MAX DISCH TEMP OF { Q } oF AND A MAX TEMP RISE OF
{ Z } oF AND CANNOT BE USED BELOW -40 oF
THIS HEATER HAS BEEN DESIGNED TO OPERATE AT A MINIMUM
{
} CFM OF VENTILATION AIR TO PROPERLY DILUTE ITS
I
COMBUSTION PRODUCTS BASED ON A MINIMUM ROOM AIR
TEMPERATURE OF 55 oF, A MINIMUM OUTDOOR TEMPERATURE
OF -40 oF, AND A MAXIMUM DISCHARGE TEMPERATURE OF
{ Q } oF. SEE INSTALLATION INSTRUCTIONS FOR OTHER
LIMITATIONS FOR RE-CIRCULATION APPLICATIONS.
MAXIMUM INPUT RATING
{
J
MINIMUM INPUT RATING
{
K
NORMAL MANIFOLD PRESS.
{
L
MIN GAS INLET PRESS. FOR BURN. ADJ. {
MAX PERMISSIBLE GAS SUPPLY PRESS. {
MIN PRESSURE DROP ACROSS BURNER
MAX PRESSURE DROP ACROSS BURNER

}
}
}
M
N
0.25
0.75

BTU/HR
BTU/HR
IN WC
} IN WC
} PSI
IN WC
IN WC

CLEARANCES TO COMBUSTIBLES:
TOP, BOTTOM, AND SIDE OPPOSITE CONTROLS - 1 INCH
FOR SERVICE ON CONTROL SIDE OF UNIT - WIDTH OF UNIT
INSTALL UNITS IN ACCORDANCE TO THE MOST RECENT
STAND. ANSI/NFPA 409 IF INSTALLED IN AIRCRAFT HANGERS
STAND. ANSI/NFPA 88A IF INSTALLED IN PARKING STRUCTURES
STAND. ANSI/NFPA 88B IF INSTALLED IN REPAIR GARAGES

ADDITIONAL REFERENCES
Forms:
•
•
•
•
•
•

Model RDF

Installation Form I-RDF, Model RDF
Operation/Maintenance/Service Form O-ADF/DV/RDF
Installation Form I-OPT-C, Roof Curb Installation Instructions
Parts Form P-GC, Gas Conversion
Parts Form P-VALVES, Serial No., Gas Valves, and Maxitrol Gas Controls
Instruction Form CP-RDF-IGN, Conversion to Hot Surface Ignition

Website: www.RezSpec.com (Forms are available to download.)

Rating Plate Codes:
A = Model No.
B = Gas Type (Nat or LP)
C = Motor HP
D = Volt
E = Phase
F = Maximum Total Input
Amps for Unit
G = SCFM
H = ESP
I = CFM
J = Maximum Input

K = Minimum Input
L = Manifold Presssure
M = Minimum Inlet
Pressure
N = Maximum Supply
Pressure
P = Wiring Diamgram No.
Q = Maximum Discharge
Temperature
Z = Maximum Temperature
Rise °F
Form P-RDF, Page 1

Serial No.

Rating Plate and
Serial No. (cont'd)

Example:

ANH

61

K2

N

1

2

3

4

40297 CA
5

MV7

6

7

Codes:
1 = Date of manufacture (see chart on page 2)
2 = Type of pilot
3 = Type of valve
4 = Type of gas (N= Natural;
L= Propane)
5 = Consecutive number
6 = Type of air control (CA=Constant Air Volume; VA=Variable Air Volume;
RA=Recirculation Air)
7 = Type of Maxitrol gas control (MV7=Maxitrol System 14; MV8=Maxitrol System 14A;
MV9=Maxitrol System 44; MVB=Maxitrol System 94; MVC=with Maxitrol A200
Conditioner; MVD=Maxitrol System 14E; MVE-Maxitrol System 44E-21; MVF-Maxitrol
System 44ER-21)

First Element of the Serial Number - Date of Manufacture

Year
1984
1985
1986
1987
1988
1989
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015

Jan
AJA
AKA
ALA
AMA
ANA
AOA
APA
AQA
ARA
ASA
ATA
AUA
AVA
AWA
AXA
AYA
AZA
BAA
BBA
BCA
BDA
BEA
BFA
BGA
BHA
BIA
BJA
BKA
BLA
BMA
BNA
BOA

Form P-RDF, Page 2

Feb
AJB
AKB
ALB
AMB
ANB
AOB
APB
AQB
ARB
ASB
ATB
AUB
AVB
AWB
AXB
AYB
AZB
BAB
BBB
BCB
BDB`
BEB
BFB
BGB
BHB
BIB
BJB
BKB
BLB
BMB
BNB
BOB

Mar
AJC
AKC
ALC
AMC
ANC
AOC
APC
AQC
ARC
ASC
ATC
AUC
AVC
AWC
AXC
AYC
AZC
BAC
BBC
BCC
BDC
BEC
BFC
BGC
BHC
BIC
BJC
BKC
BLC
BMC
BNC
BOC

Apr
AJD
AKD
ALD
AMD
AND
AOD
APD
AQD
ARD
ASD
ATD
AUD
AVD
AWD
AXD
AYD
AZD
BAD
BBD
BCD
BDD
BED
BFD
BGD
BHD
BID
BJD
BKD
BLD
BMD
BND
BOD

May
AJE
AKE
ALE
AME
ANE
AOE
APE
AQE
ARE
ASE
ATE
AUE
AVE
AWE
AXE
AYE
AZE
BAE
BBE
BCE
BDE
BEE
BFE
BGE
BHE
BIE
BJE
BKE
BLE
BME
BNE
BOE

June
AJF
AKF
ALF
AMF
ANF
AOE
APF
AQF
ARF
ASF
ATF
AUF
AVF
AWF
AXF
AYF
AZF
BAF
BBF
BCF
BDF
BEF
BFF
BGF
BHF
BIF
BJF
BKF
BLF
BMF
BNF
BOF

July
AJG
AKG
ALG
AMG
ANG
AOG
APG
AQG
ARG
ASG
ATG
AUG
AVG
AWG
AXG
AYG
AZG
BAG
BBG
BCG
BDG
BEG
BFG
BGG
BHG
BIG
BJG
BKG
BLG
BMG
BNG
BOG

Aug
AJH
AKH
ALH
AMH
ANH
AOH
APH
AQH
ARH
ASH
ATH
AUH
AVH
AWH
AXH
AYH
AZH
BAH
BBH
BCH
BDH
BEH
BFH
BGH
BHH
BIH
BJH
BKH
BLH
BMH
BNH
BOH

Sept
AJI
AKI
ALI
AMI
ANI
AOI
API
AQI
ARI
ASI
ATI
AUI
AVI
AWI
AXI
AYI
AZI
BAI
BBI
BCI
BDI
BEI
BFI
BGI
BHI
BII
BJI
BKI
BLI
BMI
BNI
BOI

Oct
AJJ
AKJ
ALJ
AMJ
ANJ
AOJ
APJ
AQJ
ARJ
ASJ
ATJ
AUJ
AVJ
AWJ
AXJ
AYJ
AZJ
BAJ
BBJ
BCJ
BDJ
BEJ
BFJ
BGJ
BHJ
BIJ
BJJ
BKJ
BLJ
BMJ
BNJ
BOJ

Nov
AJK
AKK
ALK
AMK
ANK
AOK
APK
AQK
ARK
ASK
ATK
AUK
AVK
AWK
AXK
AYK
AZK
BAK
BBK
BCK
BDK
BEK
BFK
BGK
BHK
BIK
BJK
BKK
BLK
BMK
BNK
BOK

Dec
AJL
AKL
ALL
AML
ANL
AOL
APL
AQL
ARL
ASL
ATL
AUL
AVL
AWL
AXL
AYL
AZL
BAL
BBL
BCL
BDL
BEL
BFL
BGL
BHL
BIL
BJL
BKL
BLL
BML
BNL
BOL

Electrical Control Compartment Typical Component Locations
See below and the following pages for P/N's and illustrations.
NOTE: Illustration shows approximate locations of controls on RDF Series 3 systems. Manufacture of Series 3 system began
in 9/03. RDF systems manufactured prior to Series 3 have similar controls but control locations are different. Because this
product has experienced ongoing development, always provide complete model and serial number when inquiring about or
ordering replacement parts.
Control
Relays

Time Delay
Relay

Outside Air Cutoff
(high ambient limit control)

24-volt Terminals

Return
Air
Damper
Motor

Maxitrol Amplifier
or Signal Conditioner

Circuit
Board

Service
Switches

High
Optional Dirty Filter
Pressure Switch

Transformer

Ignition
Module

24-Volt Terminals

Status Lights

Bypass
Damper
Motor

Motor
Starter

Low

Standard Pressure
Switches

Relay for
Optional 2-Speed

Starter
Relay

Line Voltage
Terminals

Model RDF Series 3 Control
Compartment
Control Relays
Contactor
or Starter
Electrical
Box

Dirty
Filter
Switch

Ignitor
Module

Transformer

Circuit
Analyzer
Amplifier
or Signal
Conditioner
High and Low
Pressure Switches
Gas Train/
Manifold

Form P-RDF, Page 3

Electrical Components
CODE
1A
1B
2A
2B
3
4A
4B
5
6A
6B
7
8
9
10
11
12
13
14
15
16
17
18A
18B
19
20A
20B
21
22
22A
22B
23
24
25
26A
26B
27A
27B
28
29
30
31
32
33
34

Description
RBM Relay, SP-ST,
Hamilton Standard #84-20102-101
Codes 1A&B are
Hamilton Standard #134-20102-101
24V Coil
interchangeable.
Codes 2A&B are
RBM Relay, SP-DT, Hamilton Standard #84-20103-301
Products Unltd 9400-04-Q180
interchangeable.
24V Coil
Time Delay Relay (Low Fire), 24V Coil, Thermodisc #F12S20, Style 305005
Codes 4A&B are
RBM Relay, SP-ST,
Hamilton Standard #84-50202-101
Hamilton Standard #134-50202-101
interchangeable.
120V Coil
Time Delay Relay (for freezestat bypass), T&B Agastst #VTM1ULA
RBM Relay, SP-DT, Hamilton Standard #84-50203-301
Codes 6A&B are
Hamilton Standard #134-50203-301
120V Coil
interchangeable.
Prepurge Time Delay Relay, 24V Coil, Thermodisc #12S20
Relay, 24V Coil, Essex #91-102006-1300
Manual Reset Limit, Thermodisc 330545, L150
Automatic Limit, L135, Thermodisc #60T11-312616
Outside Air Cutoff (High Ambient Limit) & Freezestat, J/C #A19AAF-12C
Flame Safety Limit (ECO), Opens 306°F, Thermodisc #G4AP0200152C
Firestat, Honeywell #L4029E1029, 200°F
Spark Generator, 120V, Honeywell #Q624A1014
Low Air Pressure Switch, IS2-0233-5275 for RDF Series 3
Low Air Pressure Switch Kit replaces P/N 86986, #FS4197-166 or PPS10175-3043
High Air Pressure Switch, IS2-0233-5273 for RDF Series 3
High Air Pressure Switch Kit replaces P/N 86987, #FS4197-164 or PPS10175-3041
Plastic Tee for Air Pressure Tubing, 3/16", 1/16" I.D.
Yellow Plastic Tubing for air pressure switch, 3/16" O.D. x 14"
Clear Plastic Tubing for Air Pressure Switch, 3/16" O.D. x 3 ft
Bushing and Insect Screen for Sensing Probes (not illustrated)
Air Pressure Switch, IS2-0233-5274 for RDF Series 3
Air Pressure Switch Kit replaces P/N 87250, #FS4197-165 or PPS10175-3042
Air Pressure Switch, IS2-0233-5276 for RDF Series 3
Air Pressure Switch Kit replaces P/N 87249, #FS4197-171 or PPS10175-3044
Contactor, Furnace 42AF15AJ, 24V (used with Option BM80 and BM81 manifold)
Diagnostic Circuit Analyzer Board
Replacement Bulb for Circuit Analyzer Board, RDF Series 3
Replacement Light for Circuit Analyzer Board (Option BS2 prior to RDF Series 3)
Replacement Relay for Code 22, SKMP-2C-24AC
Terminal Block, #KT3
Terminal Block Adapter
Convenience Outlet Receptacle, Hubbell #GF5362 (separate electrical supply)
Dirty Filter Pressure Switch, Tri-Delta #AP4434, set at .3" w.c.
Clear Plastic Tubing for Dirty Filter Pressure Switch, 3/16" O.D. x 112"
Fuseholder, 24V, Wesco #S257A57G01
Fuseholder, Buss Model HTB-481
Fuses - See descriptions and list of P/N's on page 5.
Transformer - See descriptions and list of P/N's on page 5.
DPDT System Switch, Winter/Off/Summer, Cutler Hammer 7561K6
SPDT Switch (service switch), Cutler Hammer 7505K6
Null Pressure Switch, .01" - .20" w.c., Dwyer #1640-0
Potentiometer, Honeywell 112894FA
Photohelic Pressure Sensor in Options AR36 & AR37, 3000-00-N24 Vac

CODE 1B Relay,
P/N 98118

CODE 2B Relay,
P/N 103317

CODE 5 Time Delay
Relay
(Freezestat),
P/N 89661

CODE 6 Relay,
P/N
103318

Form P-RDF, Page 4

Location

Control Compartment
Control Compartment

P/N
14747
98118
18549
103317
89254
86982
103319
89661
90205
103318
52887
110656
82610
86979
126170
82414
42782
86974
207178
193806
207176
193807
87482
122855
102401
96794
207177
193809
207179
193808
203935
151263
125189
101889
151271
144972
144973
96912
105507
179302
38635
60241

Space (Console)
Control Compartment
Heated Space
Space / Remote Console
Remote

101900
101901
88052
16110
158893

Control Compartment
Control Compartment
Control Compartment
Control Compartment
Control Compartment
Control Compartment
Control Compartment
Control Compartment
Blower Discharge
Blower Discharge
Control Compartment
Gas Train Compartment
Blower Discharge
Control Compartment
Control Compartment
Control Compartment
Control Compartment
Control Compartment

Control Compartment
Control Compartment
Control Compartment
Control Compartment
Control Compartment &
Remote Console
Control Compartment
Control Compartment

CODE 3 Time Delay
Relay
(Low Fire),
P/N 89254
(On units mfgd prior to 3/96)
CODE 7 Prepurge
Time Delay
Relay,
P/N 52887

CODE 4B Relay,
P/N 103319

CODE 8 Relay,
P/N 110656

CODE 9 Limit Switch,
P/N 82610

Reset
Button

CODE 10
- Limit,
P/N
86979

CODE 11, - Adjustable
Outside Air Cutoff Control
and Freezestat,
P/N 126170
(Replaces
P/N 16108)

(Automatic Reset)
CODE 12 - ECO Limit,
P/N 82414

CODE 13 Firestat,
P/N 42782

Grommet
Clamp, P/N 131993;
Cable Clamp, P/N 132065

CODE 14 Spark
Generator,
P/N 86974

CODE 15 - Low Air
Pressure Switch,
P/N 207178

(On units
mfgd
prior to
3/96)
CODE 17 - Tee
for Air
Pressure
Tubing,
P/N 87482

CODE 16 - High Air
Pressure Switch,
P/N 207176

CODE 20A - Air
Pressure Switch,
P/N 207177

Replace pressure
switch P/N 86986
with Kit P/N 193806.

CODE 20B - Air
Pressure Switch,
P/N 207179

CODE 21 - Contactor,
Furnas 42AF15AJ,
24V, (used with Option
BM80 and BM81
manifold, P/N 203935

CODE 18A - Clear Plastic
Tubing, P/N 102401 (3')
Replace pressure
Replace pressure switch
switch P/N 86987
CODE 18B - Yellow Plastic P/N 87250 with Kit P/N
with Kit P/N 193807. Tubing, P/N 122855 (14") 193809.
CODE 22 - Circuit Analyzer
Board, P/N 151263 (Std
beginning with RDF Series 3.
Option BS2 prior to Series 3.)

CODE 23 Terminal
Block,
P/N
144972

CODE 22A, Replacement
Lights for Circuit Analyzer
Board - P/N 125189 Series 3;
prior to Series 3, P/N 101889
CODE 22B, Replacement
Relay for Board, P/N 151271
Fuseholders and Fuses
CODE 27A Fuseholder,
P/N 38635

CODE 27B - Fuseholder,
P/N 60241
(used with spark ignition)
CODE 29 - Transformers
40VA

200-500
VA

Replace pressure switch
P/N 87249 with Kit P/N
193808.

CODE 25 Convenience
Outlet
Receptacle,
P/N 96912

CODE 24 Terminal
Block
Adapter,
P/N 144973
CODE 28 Fuses

Description
2.5 Amp, #3210 (spark ignition)
Bussman FRN-R15, 230/1
Bussman FRN-R30, 208/230/3
Bussman FRN-R10, 208/3
Bussman FRN-R7, 230/3
Bussman FRN-R25, 208/3
Bussman FRN-R60
Bussman FRN-R50
Bussman FRN-R90
Bussman FRN-R150

CODE 26A - Dirty Filter
Pressure Switch, P/N
105507 (replaces P/N
102773)

CODE 26B - Clear Plastic
Tubing, 3/16", P/N 179302
P/N
61542
14667
31892
89265
16207
45054
31895
87957
89931
91077

Description
Bussman FRN-R175
Bussman FRS-R3.5, 460/3
Bussman FRS-R8, 460/3
Bussman FRS-R5, 460/3
Bussman FRS-R15, 460/3
Bussman FRS25
Bussman FRS-R40
8 Amp, Fusetron 3AG-8
(hot surface ignition)
5 Amp, Fusetron MDL 3AG

P/N
91595
89266
89268
89267
87638
31891
89936
38636
90335

Volts In Volts Out VA Manufacturer's No.
Reznor P/N
115
24
200 Hevi-Duty #2223018T00
38634
(used with hot surface ignition)
115
24
40 Basler #BE141650-WAA
103055
(Used with spark igntion) (2 required to replace P/N 61806)
208/230
24
40 Basler #BE21539001
103497
(2 required to replace P/N 61807)
208
110
500 Hevi-Duty #2227003T00
86998
230/460
24
200 Siemens MT0200JX24
39095
230/460
110
500 Hevi-Duty #2227001T00
86997
460
24
40 Basler #BE23975001
103498
(2 required to replace P/N 61808)
Form P-RDF, Page 5

Electrical Components (cont'd)
CODE 32 Potentiometer,
P/N 16011 (remote
damper motor
control in Options
AR 19 and 22)

CODE 30 - DPDT
System Switch,
P/N 101900
(winter/off/
summer)

CODE 32 - Null Pressure
Switch, P/N 88052
(remote damper motor
control in Air Control
Options AR 20 and 23)

CODE 31 DPDT System
Switch,
P/N 101901
(service
switch)

CODE 34 - Photohelic Pressure
Sensor, P/N 158893 (remote
damper motor control in Air
Control Options AR 36 and 37)

CODE 35 - Sampling Tube
only, P/N 159714

Blower Motors, Contactor, and Starters
CODE 36

CODE 35 - BLOWER MOTOR

CODE 37

Motors in the table below that do not have a CODE 36 contactor listed do not have internal
overload protection and MUST be used with the CODE 37 motor starter and starter overload.
If a contactor is listed, motor may be used with either the contactor or the optional starter.

CODE 36 - Replacement Contactor (Option AN2)
Motor contactor, P/N 119625, Mfr #42AF35AJ-24V coil

Contactor

Starter
(24V)

CODE 37 - Replacement Starter (24V) & Overload (Option AN10)
Overload

(Located in the electrical compartment;
see location on page 3.)

Type
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN

HP
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
3
3
3
3
3
3

CODE 35 -Motor
P/N
Model No.
BF2054
102627
BF2054
102627
BF2054
102627
H880
159183
H880
159183
H880
159183
H991
202089
312P629
93548
312P629
93548
312P629
93548
312P696
36951
312P696
36951
312P696
36951
H992
202090
C523
13685
C523
13685
C523
13685
H882
36580
H882
36580
H882
36580
E1006
158175
C621
194202
C621
194202
C621
194202
H884
115859
H884
115859
H884
115859
E1007
158162
RB1204A
202581
RB1204A
202581
RB1204A
202581
H886
159327
H886
159327
H886
159327
E1008
158176
B735
111560
B735
111560
H845
159185
H845
159185
H845
159185
H954
120019

Form P-RDF, Page 6

Frame
56Z
56Z
56Z
LA56
LA56
LA56
H56
B56
B56
B56
D56
D56
D56
H56
H56
H56
H56
F56
F56
F56
N143T
56
56
56
UA56
UA56
UA56
R145T
56
56
56
56HZ
56HZ
56HZ
P145T
L56
L56
P56HZ
P56HZ
P56HZ
N56HZ

fla
8.8
5.1
4.4
2.5
3.0
1.5
0.9
11.0
6.3
5.5
2.9
2.6
1.3
1.0
13.0
7.5
6.5
3.7
3.2
1.6
1.1
15.0
7.8
7.5
5.6
5.0
2.8
1.6
24.6
12.3
12.3
7.0
6.6
3.5
2.1
13.7
12.4
9.0
8.6
4.3
3.6

When ordering a replacement IEC starter or overload, check the manufacturer's number on both
parts. If the number is different than that listed, both components must be replaced. IEC Starter
(contactor) and overload are mounted on rail, P/N 111387.
If Model RDF was manufactured prior to 1996, check to see if the IEC starter is line
voltage or 24 volt. If line voltage, select replacement starter on pages 9-10. If the motor
has a NEMA starter (units mfgd before 1991), see the replacement parts on page 10.
Shaft Volt ph
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
7/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
5/8"
5/8"
7/8"
7/8"
7/8"
7/8"

120
208
240
208
240
480
575
120
208
240
208
240
480
575
120
208
240
208
240
480
575
120
208
240
208
240
480
575
120
208
240
208
240
480
575
208
230
208
240
480
575

1
1
1
3
3
3
3
1
1
1
3
3
3
3
1
1
1
3
3
3
3
1
1
1
3
3
3
3
1
1
1
3
3
3
3
1
1
3
3
3
3

Service Power Efficiency CODE 37 - Starter (24V)
Factor Factor
Mfr No.
P/N
%
1.15
CL00A310T-1 151275
1.15
CL00A310T-1 151275
1.15
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL01A310T-1 151276
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.25
CL01A310T-1 151276
1.25
CL00A310T-1 151275
1.25
CL00A310T-1 151275
1.15
79%
CL00A310T-1 151275
1.15
79%
CL00A310T-1 151275
1.15
79%
CL00A310T-1 151275
1.15
82.50% CL00A310T-1 151275
1.2
86.4
77.20% CL01A310T-1 151276
1.2
86.4
77.20% CL00A310T-1 151275
1.2
86.4
77.20% CL00A310T-1 151275
1.15
66.4
78.60% CL00A310T-1 151275
1.15
66.4
78.60% CL00A310T-1 151275
1.15
66.4
78.60% CL00A310T-1 151275
1.15
85.3
84.00% CL00A310T-1 151275
CL04A310M-1 151279
CL01A310T-1 151276
CL01A310T-1 151276
1.15
67
79%
CL00A310T-1 151275
1.15
67
79%
CL00A310T-1 151275
1.15
67
79%
CL00A310T-1 151275
1.15
86
84.00% CL00A310T-1 151275
1.15
CL01A310T-1 151276
1.15
CL01A310T-1 151276
1.15
CL00A310T-1 151275
1.15
CL00A310T-1 151275
1.15
CL00A310T-1 151275
1.15
80.3
83.80% CL00A310T-1 151275

min
8.00
4.00
4.00
1.80
2.50
1.30
0.65
10.00
5.50
4.00
2.50
2.50
1.00
0.65
10.00
5.50
5.50
2.50
2.50
1.30
1.00
10.00
5.50
5.50
4.00
4.00
2.50
1.30
21.00
10.00
10.00
5.50
5.50
2.50
1.80
10.00
10.00
8.00
8.00
4.00
2.50

Starter Overload
max
GE #
P/N
12.00 RTA1-N 151193
6.30 RTA1-L 151191
6.30 RTA1-L 151191
2.70 RTA1-J 151189
4.10 RTA1-K 151190
1.90 RTA1-H 151188
1.10 RTA1-F 151186
16.00 RTA1-P 151194
8.50 RTA1-M 151192
6.30 RTA1-L 151191
4.10 RTA1-K 151190
4.10 RTA1-K 151190
1.50 RTA1-G 151187
1.10 RTA1-F 151186
16.00 RTA1-P 151194
8.50 RTA1-M 151192
8.50 RTA1-M 151192
4.10 RTA1-K 151190
4.10 RTA1-K 151190
1.90 RTA1-H 151188
1.50 RTA1-G 151187
16.00 RTA1-P 151194
8.50 RTA1-M 151192
8.50 RTA1-M 151192
6.30 RTA1-L 151191
6.30 RTA1-L 151191
4.10 RTA1-K 151190
1.90 RTA1-H 151188
26.00 RTA1-U 151198
16.00 RTA1-P 151194
16.00 RTA1-P 151194
8.50 RTA1-M 151192
8.50 RTA1-M 151192
4.10 RTA1-K 151190
2.70 RTA1-J 151189
16.00 RTA1-P 151194
16.00 RTA1-P 151194
12.00 RTA1-N 151193
12.00 RTA1-N 151193
6.30 RTA1-L 151191
4.10 RTA1-K 151190

CODE 36 - Contactor
Mfr No.
P/N
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
============ ===
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===

Blower Motors, Contactor, and Starters (cont'd)
Type
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC

HP
5
5
5
5
5
5
7.5
7.5
7.5
7.5
7.5
7.5
10
10
10
10
10
10
15
15
15
15
20
20
20
20
25
25
25
25
30
30
30
30
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
3
3
3
3
3
3
5
5
5
5
5

CODE 35 - Motor
P/N
Model No.
V211
111562
V211
111562
196033
113371
196033
113371
196033
113371
H956
120020
V305
105828
V305
105828
E302
105854
E300
105855
E300
105855
E324
158164
V303
105830
V303
105830
E303
105857
E301
105858
E301
105858
E325
158163
142287 B-FM2513T-8
142288 BALD-FM2513T
142288 BALD-FM2513T
142289 B-EFM2513T-5
142295 B-FM2515T-8
142296 BAL-FM2515T
142296 BAL-FM2515T
142297 B-FM2515T-5
E545-F2
159021
E546-F2
159022
E546-F2
159022
E594-F2
159023
E547-F2
159024
E548-F2
159025
E548-F2
159025
E595-F2
159026
C613
159184
C613
159184
C613
159184
H274
16077
H274
16077
H274
16077
H276
105568
F353
115860
F353
115860
F353
159184
H580
20371
H580
20371
H580
20371
H461
105569
159105
174993
159105
174993
159105
174993
H524
16080
H524
16080
H524
16080
H525
105570
311P402
94347
311P402
94347
311P402
94347
H535
101286
H535
101286
H535
101286
E127
105665
K200
105572
L3516TM
205881
E166
158165
E166
158165
E166
158165
E169
158166
K222
111564
K222
111564
B - M3559T
159330
B - M3559T
159330
B - M3559T
159330
B-M3559T-5
111571
K223
111567
E241
155048
E241
155048
E241
155048
E273
158170

Frame
L184T
L184T
Y56HZ
Y56HZ
Y56HZ
Y56HZ
S215T
S215T
F213T
213T
213T
S213T
S215T
S215T
F215T
215T
215T
S215T
254T
254T
254T
254T
256T
256T
256T
256T
S284T
S284T
S284T
S284T
S286T
S286T
S286T
S286T
J56
J56
J56
H56
H56
H56
J56
F56
F56
F56
KA56
KA56
KA56
L56
L56
L56
L56
J56
J56
J56
H56
TK56H
TK56H
TK56H
L56H
L56H
L56H
M145T
F182T
F182T
145T
145T
145T
145T
F184T
F184T
145T
145T
145T
145T
F184T
184T
184T
184T
184T

fla
28.3
25.6
13.4
13.2
6.6
5.4
35.4
32.0
22.5
19.4
9.7
7.8
42.0
38.0
31.0
26.0
13.0
10.4
43.1
39.0
19.5
16.0
58.7
53.0
26.5
21.2
69.8
60.6
30.3
24.3
78.0
75.0
37.5
30.0
7.2
3.5
3.6
2.3
2.0
1.0
0.7
11.0
5.4
5.5
2.0
2.2
1.1
0.8
12.0
6.2
6.0
3.3
3.4
1.7
1.4
16.4
9.5
8.2
4.3
4.4
2.2
1.6
24
8.3
7.0
5.8
2.9
2.3
30.0
15.0
7.9
7.2
3.6
3
20.2
16
12
6
4.8

Shaft Volt ph
1-1/8"
1-1/8"
7/8"
7/8"
7/8"
7/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-7/8"
1-7/8"
1-7/8"
1-7/8"
1-7/8"
1-7/8"
1-7/8"
1-7/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
5/8"
7/8"
1-1/8"
7/8"
7/8"
7/8"
7/8"
7/8"
1-1/8"
1-1/8"
7/8"
7/8"
7/8"
7/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"

208
240
208
240
480
575
208
230
208
240
480
575
208
230
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
120
208
240
208
240
480
575
120
208
240
208
240
480
575
120
208
240
208
240
480
575
120
208
240
208
240
480
575
120
240
208
240
480
575
120
240
208
240
480
575
240
208
240
480
575

1
1
3
3
3
3
1
1
3
3
3
3
1
1
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
1
1
1
3
3
3
3
1
1
1
3
3
3
3
1
1
1
3
3
3
3
1
1
1
3
3
3
3
1
1
3
3
3
3
1
1
3
3
3
3
1
3
3
3
3

Service Power Efficiency CODE 37 - Starter (24V)
%
Factor Factor
Mfr No.
P/N
CL04A310M-1 151279
CL04A310M-1 151279
1.15
87.2
85%
CL01A310T-1 151276
1.15
87.2
85%
CL01A310T-1 151276
1.15
87.2
85%
CL00A310T-1 151275
1.15
85.9
85.30% CL00A310T-1 151275
CL06A311M-1 203687
CL06A311M-1 203687
CL04A310M-1 151279
CL25A310T-1 151278
CL00A310T-1 151275
CL00A310T-1 151275
CL06A311M-1 203687
CL06A311M-1 203687
CL04A310M-1 151279
CL04A310M-1 151279
CL01A310T-1 151276
CL01A310T-1 151276
CL06A311M-1 203687
CL06A311M-1 203687
CL25A310T-1 151278
CL02A310T-1 151277
1.15
80
88.50% CL07A311M-1 203793
1.15
81
88.50% CL07A311M-1 203793
1.15
81
88.50% CL04A310M-1 151279
1.15
80
88.50% CL25A310T-1 151278
1.15
84.1
91.70% CL09A311M-1 203794
1.15
84.1
91.70% CL07A311M-1 203793
1.15
84.1
91.70% CL04A310M-1 151279
1.15
84.1
91.70% CL04A310M-1 151279
1.15
81
92.40% CL09A311M-1 203794
1.15
81
92.40% CL09A311M-1 203794
1.15
81
92.40% CL06A311M-1 203687
1.15
81
92.40% CL04A310M-1 151279
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
1
59.5
74.80% CL00A310T-1 151275
1
59.5
74.80% CL00A310T-1 151275
1
59.5
74.80% CL00A310T-1 151275
1.15
76.4
77%
CL00A310T-1 151275
CL01A310T-1 151276
CL00A310T-1 151275
CL00A310T-1 151275
1
73.5
81.10% CL00A310T-1 151275
1
73.5
81.10% CL00A310T-1 151275
1
73.5
81.10% CL00A310T-1 151275
1.15
78.3
82%
CL00A310T-1 151275
CL01A310T-1 151276
CL00A310T-1 151275
CL00A310T-1 151275
1
74.4
80.20% CL00A310T-1 151275
1
74.4
80.20% CL00A310T-1 151275
1
74.4
80.20% CL00A310T-1 151275
1.15
71.6
80.40% CL00A310T-1 151275
CL02A310T-1 151277
CL00A310T-1 151275
CL00A310T-1 151275
1
80.9
82.40% CL00A310T-1 151275
1
80.9
82.40% CL00A310T-1 151275
1
80.9
82.40% CL00A310T-1 151275
1.15
85.7
84%
CL00A310T-1 151275
CL04A310M-1 151279
1.15
99
78%
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL04A310M-1 151279
CL02A310T-1 151277
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL25A310T-1 151278
CL02A310T-1 151277
CL01A310T-1 151276
CL00A310T-1 151275
CL00A310T-1 151275

min
25.00
25.00
10.00
10.00
5.50
4.00
30.00
30.00
21.00
17.50
8.00
5.50
30.00
30.00
25.00
25.00
10.00
10.00
42.00
30.00
17.50
14.50
54.00
42.00
25.00
17.50
64.00
54.00
25.00
21.00
64.00
64.00
30.00
25.00
5.50
2.50
2.50
1.80
1.80
0.65
0.65
10.00
4.00
4.00
1.80
1.80
1.00
0.65
10.00
4.00
4.00
2.50
2.50
1.30
1.00
14.50
8.00
8.00
4.00
4.00
1.80
1.30
21.00
5.50
5.50
4.00
2.50
1.90
25.00
14.50
5.50
5.50
2.50
2.50
17.50
14.50
10.00
4.00
4.00

Starter Overload
max
GE #
P/N
32.00 RTA1-V 151199
32.00 RTA1-V 151199
16.00 RTA1-P 151194
16.00 RTA1-P 151194
8.50 RTA1-M 151192
6.30 RTA1-L 151191
43.00 RTA2-E 151206
43.00 RTA2-E 151206
26.00 RTA1-U 151198
22.00 RTA1-T 151197
12.00 RTA1-N 151193
8.50 RTA1-M 151192
43.00 RTA2-E 151206
43.00 RTA2-E 151206
32.00 RTA1-V 151199
32.00 RTA1-V 151199
16.00 RTA1-P 151194
16.00 RTA1-P 151194
55.00 RTA2-G 151202
43.00 RTA2-E 151206
22.00 RTA1-T 151197
18.00 RTA1-S 151196
65.00 RTA2-H 151203
55.00 RTA2-G 151202
32.00 RTA1-V 151199
22.00 RTA1-T 151197
82.00 RTA2-J 151204
65.00 RTA2-H 151203
32.00 RTA1-V 151199
26.00 RTA1-U 151198
82.00 RT2-J 151204
82.00 RT2-J 151204
43.00 RTA2-E 151206
32.00 RTA1-V 151199
8.50 RTA1-M 151192
4.10 RTA1-K 151190
4.10 RTA1-K 151190
2.70 RTA1-J 151189
2.70 RTA1-J 151189
1.10 RTA1-F 151186
1.10 RTA1-F 151186
16.00 RTA1-P 151194
6.30 RTA1-L 151191
6.30 RTA1-L 151191
2.70 RTA1-J 151189
2.70 RTA1-J 151189
1.50 RTA1-G 151187
1.10 RTA1-F 151186
16.00 RTA1-P 151194
6.30 RTA1-L 151191
6.30 RTA1-L 151191
4.10 RTA1-K 151190
4.10 RTA1-K 151190
1.90 RTA1-H 151188
1.50 RTA1-G 151187
18.00 RTA1-S 151196
12.00 RTA1-N 151193
12.00 RTA1-N 151193
6.30 RTA1-L 151191
6.30 RTA1-L 151191
2.70 RTA1-J 151189
1.90 RTA1-H 151188
26.00 RTA1-U 151198
8.50 RTA1-M 151192
8.50 RTA1-M 151192
6.30 RTA1-L 151191
4.10 RTA1-K 151190
2.70 RTA1-J 151189
32.00 RTA1-V 151199
18.00 RTA1-S 151196
8.50 RTA1-N 151192
8.50 RTA1-N 151192
4.10 RTA1-K 151190
4.10 RTA1-K 151190
22.00 RTA1-T 151197
18.00 RTA1-S 151196
16.00 RTA1-P 151194
6.30 RTA1-L 151191
6.30 RTA1-L 151191

CODE 36 - Contactor
Mfr No.
P/N
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
42AF35AJ-24V 119625
============ ===
============ ===
42AF35AJ-24V 119625
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===

(continued)
Form P-RDF, Page 7

Blower Motors, Contactor, and Starters (cont'd)
Type
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE

HP
7.5
7.5
7.5
7.5
7.5
10
10
10
10
10
15
15
15
20
20
20
1
1
1
1
1 1/2
1 1/2
1 1/2
1 1/2
2
2
2
2
3
3
3
3
5
5
5
5
7 1/2
7 1/2
7 1/2
7 1/2
10
10
10
10
15
15
15
15
20
20
20
20

CODE 35 - Motor
P/N
Model No.
K305
105842
E356
158171
E356
158171
E356
158171
E364
158172
K313
105846
E357
158173
E357
158173
E357
158173
E365
158174
142443 BAL-FM2333T
142443 BAL-FM2333T
B-FM2333-5
142444
142301 BAL-FM2334T
142301 BAL-FM2334T
142302 B-FM2334T-5
E103
105659
E1015
159328
E1015
159328
E1006
158175
E104
105662
E1016
159329
E1016
159329
E1007
158162
E105
105664
E1017
159027
E1017
159027
E1008
158176
159186 B-35L405S489G3
B-EM3158T
159028
B-EM3158T
159028
159030 B-35L405S709G1
E204
159029
E204
159029
E204
159029
111602 BAL-M3613T-5
E316
159331
E317
159332
E317
159332
E324
158164
E318
159333
E397
159334
E397
159334
E325
158163
142440 B-EFM2513T-8
142441 B-EFM2513T
142441 B-EFM2513T
142289 B-EFM2513T-5
C-E452-F2
159187
142299 B-EFM2515T
142299 B-EFM2515T
142300 B-EFM2515T-5

Frame
F215T
213T
213T
213T
213T
215T
215T
215T
215T
215T
254T
254T
254T
256T
256T
256T
N143T
143T
143T
N143T
P145T
145T
145T
R145T
P145T
145T
145T
P145T
145T
145T
145T
145T
H182T
H182T
H182T
184T
D213T
D213T
D213T
S213T
H215T
H215T
H215T
S215T
254T
254T
254T
254T
S256T
256T
256T
256T

fla
34
24
19
9.5
7.6
39
30
26
13
9.6
38
19
15
52
26
20.6
3.1
2.7
1.4
1.1
4.5
3.9
2.0
1.6
6.0
5.8
2.9
2.1
8.3
7.4
3.7
3.0
13.9
11.6
5.8
4.8
22.3
19.4
9.7
7.8
27.8
24.2
12.1
10.4
41.5
36.0
18.0
16
57.0
48.0
24.0
19.2

Shaft Volt ph
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
7/8"
1-1/8"
1-1/8"
1-1/8"
1-1/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-3/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"
1-5/8"

240
208
240
480
575
240
208
240
480
575
240
480
575
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575
208
240
480
575

1
3
3
3
3
1
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3

Service Power Efficiency CODE 37 - Starter (24V)
Factor Factor
Mfr No.
P/N
%
CL06A311M-1 203687
CL04A310M-1 151279
CL25A310T-1 151278
CL00A310T-1 151275
CL00A310T-1 151275
CL06A311M-1 203687
CL04A310M-1 151279
CL04A310M-1 151279
CL02A310T-1 151277
CL00A310T-1 151275
1.15
82
90.20% CL06A311M-1 203687
1.15
82
90.20% CL25A310T-1 151278
1.15
82
90.20% CL02A310T-1 151277
1.15
81
89.50% CL07A311M-1 203793
1.15
81
89.50% CL04A310M-1 151279
1.15
81
89.50% CL25A310T-1 151278
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL00A310T-1 151275
CL02A310T-1 151277
CL01A310T-1 151276
CL00A310T-1 151275
CL00A310T-1 151275
CL04A310M-1 151279
CL25A310T-1 151278
CL00A310T-1 151275
CL00A310T-1 151275
CL04A310M-1 151279
CL04A310M-1 151279
CL01A310T-1 151276
CL01A310T-1 151276
1.15
84
92.40% CL06A311M-1 203687
1.15
84
92.40% CL06A311M-1 203687
1.15
84
92.40% CL25A310T-1 151278
1.15
84
92.40% CL02A310T-1 151277
1.15
84
93.60% CL07A311M-1 203793
1.15
84
93.00% CL07A311M-1 203793
1.15
84
93.00% CL04A310M-1 151279
1.15
84
93.00% CL25A310T-1 151278

min
30.00
21.00
17.50
8.00
5.50
30.00
25.00
21.00
10.00
8.00
30.00
17.50
10.00
42.00
25.00
17.50
2.50
2.50
1.00
1.00
4.00
2.50
1.90
1.30
4.00
4.00
2.50
1.90
8.00
5.50
2.50
2.50
10.00
10.00
5.50
4.00
21.00
17.50
8.00
5.50
25.00
21.00
10.00
10.00
30.00
30.00
17.50
10.00
54.00
42.00
21.00
17.50

Starter Overload
max
GE #
P/N
43.00 RTA2-E 151206
26.00 RTA1-U 151198
22.00 RTA1-T 151197
12.00 RTA1-N 151193
8.50 RTA1-N 151192
43.00 RTA2-E 151206
32.00 RTA1-V 151199
26.00 RTA1-U 151198
16.00 RTA1-P 151194
12.00 RTA1-N 151193
43.00 RTA2-E 151206
22.00 RTA1-T 151197
16.00 RTA1-P 151194
55.00 RTA2-G 151202
32.00 RTA1-V 151199
22.00 RTA1-T 151197
4.10 RTA1-K 151190
4.10 RTA1-K 151190
1.50 RTA1-G 151187
1.50 RTA1-G 151187
6.30 RTA1-L 151191
4.10 RTA1-K 151190
2.70 RTA1-J 151189
1.90 RTA1-H 151188
6.30 RTA1-L 151191
6.30 RTA1-L 151191
4.10 RTA1-K 151190
2.70 RTA1-J 151189
12.00 RTA1-N 151193
8.50 RTA1-N 151192
4.10 RTA1-K 151190
4.10 RTA1-K 151190
16.00 RTA1-P 151194
16.00 RTA1-P 151194
8.50 RTA1-M 151192
6.30 RTA1-L 151191
26.00 RTA1-U 151198
22.00 RTA1-T 151197
12.00 RTA1-N 151193
8.50 RTA1-N 151192
32.00 RTA1-V 151199
26.00 RTA1-U 151198
16.00 RTA1-P 151194
16.00 RTA1-P 151194
43.00 RTA2-E 151206
43.00 RTA2-E 151206
22.00 RTA1-T 151197
16.00 RTA1-P 151194
65.00 RTA2-H 151203
55.00 RTA2-G 151202
26.00 RTA1-U 151198
22.00 RTA1-T 151197

CODE 36 - Contactor
Mfr No.
P/N
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===
============ ===

24 LB1A-C
120 LB1A-J
208 LB1A-L
230 LB1A-S
460 LB1A-U
575 LB1A-Y

Form P-RDF, Page 8

GE #

24
120
208
230
460
575

LB3A-C
LB3A-J
LB3A-L
LB3A-S
LB3A-U
LB3A-Y

For Use with
Reznor Contactors
P/N Beginning with
GE#
151286
151287
151288
CL04; CL45
151289
151290
151291

For Use with
Reznor Contactors
GE #
P/N Beginning with
GE#
208 LB4A-L 151292
CL06; CL07;
230 LB4A-S 151293
CL08; CL09
460 LB4A-U 151294
Voltage

GE #

For Use with
Reznor Contactors
P/N Beginning with
GE#
151280
151281
151282 CL00; CL01;
151283 CL02; CL25
151284
151285

Voltage

Voltage

CODE 38 - Replacement Holding Coils for IEC Starters

Replacement Line Voltage IEC Starters for RDF units manufactured before 1996
Type
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN

HP
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
5
5
5
5
5
5
7.5
7.5
7.5
7.5
7.5
7.5
10
10
10
10
10
10
15
15
15
15
20
20
20
20
25
25
25
25
30
30
30
30

Motor
P/N
102627
102627
102627
159183
159183
159183
93548
93548
93548
36951
36951
36951
13685
13685
13685
36580
36580
36580
158175
194202
194202
194202
115859
115859
115859
158162
202581
202581
202581
159327
159327
159327
158176
111560
111560
159185
159185
159185
120019
152002
152002
152002
111562
111562
113371
113371
113371
120020
105828
105828
105854
105855
105855
158164
105830
105830
105857
105858
105858
158163
142287
142288
142288
142289
142295
142296
142296
142297
159021
159022
159022
159023
159024
159025
159025
159026

CODE 39 - Starter (line voltage) and Overloads
volt ph
Mfg No.
P/N
min max
GE #
P/N
120 1 CL00A310T-J 151146 8.00 12.00 RTA1-N 151193
208 1 CL00A310T-L 151150 4.00 6.30 RTA1-L 151191
240 1 CL00A310T-S 151147 4.00 6.30 RTA1-L 151191
208 3 CL00A310T-L 151150 1.90 2.70 RTA1-J 151189
240 3 CL00A310T-S 151147 2.50 4.10 RTA1-K 151190
480 3 CL00A310T-U 151148 1.30 1.90 RTA1-H 151188
120 1 CL01A310T-J 151151 10.00 16.00 RTA1-P 151194
208 1 CL00A310T-L 151150 5.50 8.50 RTA1-M 151192
240 1 CL00A310T-S 151147 4.00 6.30 RTA1-L 151191
208 3 CL00A310T-L 151150 2.50 4.10 RTA1-K 151190
240 3 CL00A310T-S 151147 2.50 4.10 RTA1-K 151190
480 3 CL00A310T-U 151148 1.00 1.50 RTA1-G 151187
120 1 CL01A310T-J 151151 10.00 16.00 RTA1-P 151194
208 1 CL00A310T-L 151150 5.50 8.50 RTA1-M 151192
240 1 CL00A310T-S 151147 5.50 8.50 RTA1-M 151192
208 3 CL00A310T-L 151150 2.50 4.10 RTA1-K 151190
240 3 CL00A310T-S 151147 2.50 4.10 RTA1-K 151190
480 3 CL00A310T-U 151148 1.30 1.90 RTA1-H 151188
575 3 CL00A310T-Y 151149 1.00 1.50 RTA1-G 151187
120 1 CL02A310T-J 151156 10.00 16.00 RTA1-P 151194
208 1 CL00A310T-L 151150 5.50 8.50 RTA1-M 151192
240 1 CL00A310T-S 151147 5.50 8.50 RTA1-M 151192
208 3 CL00A310T-L 151150 4.00 6.30 RTA1-L 151191
240 3 CL00A310T-S 151147 4.00 6.30 RTA1-L 151191
480 3 CL00A310T-U 151148 2.50 4.10 RTA1-K 151190
575 3 CL00A310T-Y 151149 1.30 1.90 RTA1-H 151188
120 1 CL25A310T-J 151160 17.50 22.00 RTA1-T 151197
208 1 CL01A310T-L 151155 8.00 12.00 RTA1-N 151193
240 1 CL01A310T-S 151152 8.00 12.00 RTA1-N 151193
208 3 CL00A310T-L 151150 5.50 8.50 RTA1-M 151192
240 3 CL00A310T-S 151147 5.50 8.50 RTA1-M 151192
480 3 CL00A310T-U 151148 2.50 4.10 RTA1-K 151190
575 3 CL00A310T-Y 151149 1.90 2.70 RTA1-J 151189
208 1 CL02A310T-L 151159 10.00 16.00 RTA1-P 151194
240 1 CL01A310T-S 151152 10.00 16.00 RTA1-P 151194
208 3 CL00A310T-L 151150 8.00 12.00 RTA1-N 151193
240 3 CL00A310T-S 151147 8.00 12.00 RTA1-N 151193
480 3 CL00A310T-U 151148 4.00 6.30 RTA1-L 151191
575 3 CL00A310T-Y 151149 2.50 4.10 RTA1-K 151190
208 3
======
====== 8.00 12.00 RTA1-N 151193
240 3
======
====== 5.50 8.50 RTA1-M 151192
480 3
======
====== 2.50 4.10 RTA1-K 151190
208 1 CL04A310M-L 151169 25.00 32.00 RTA1-V 151199
240 1 CL04A310M-S 151166 25.00 32.00 RTA1-V 151199
208 3 CL01A310T-L 151155 10.00 16.00 RTA1-P 151194
240 3 CL01A310T-S 151152 10.00 16.00 RTA1-P 151194
480 3 CL00A310T-U 151148 5.50 8.50 RTA1-M 151192
575 3 CL00A310T-Y 151149 4.00 6.30 RTA1-L 151191
208 1 CL06A311M-L 151173 30.00 43.00 RTA2-E 151206
240 1 CL45A310M-S 151170 25.00 32.00 RTA1-V 151199
208 3 CL25A310T-L 151164 21.00 26.00 RTA1-U 151198
240 3 CL25A310T-S 151161 17.50 22.00 RTA1-T 151197
480 3 CL01A310T-U 151153 8.00 12.00 RTA1-N 151193
575 3 CL00A310T-Y 151149 5.50 8.50 RTA1-M 151192
208 1 CL06A311M-L 151173 30.00 43.00 RTA2-E 151206
240 1 CL06A311M-S 151172 30.00 43.00 RTA2-E 151206
208 3 CL04A310M-L 151169 25.00 32.00 RTA1-V 151199
240 3 CL04A310M-S 151166 25.00 32.00 RTA1-V 151199
480 3 CL01A310T-U 151153 10.00 16.00 RTA1-P 151194
575 3 CL01A310T-Y 151154 10.00 16.00 RTA1-P 151194
208 3 CL06A311M-L 151173 42.00 55.00 RTA2-G 151202
240 3 CL06A311M-S 151172 30.00 43.00 RTA2-E 151206
480 3 CL25A310T-U 151162 17.50 22.00 RTA1-T 151197
575 3 CL02A310T-Y 151158 14.50 18.00 RTA1-S 151196
208 3 CL07A311M-L 151176 54.00 65.00 RTA2-H 151203
240 3 CL07A311M-S 151175 42.00 55.00 RTA2-G 151202
480 3 CL04A310M-U 151167 25.00 32.00 RTA1-V 151199
575 3 CL25A310T-Y 151163 17.50 22.00 RTA1-T 151197
208 3 CL09A311M-L 151179 64.00 82.00 RTA2-J 151204
240 3 CL08A311M-S 151177 54.00 65.00 RTA2-H 151203
480 3 CL45A310M-U 151171 25.00 32.00 RTA1-V 151199
575 3 CL04A310M-Y 151168 21.00 26.00 RTA1-U 151198
208 3 CL09A311M-L 151179 64.00 82.00 RT2-J 151204
240 3 CL09A311M-S 151178 64.00 82.00 RT2-J 151204
480 3 CL06A311M-U 151174 30.00 43.00 RTA2-E 151206
575 3 CL04A310M-Y 119852 25.00 32.00 RTA1-V 151199

Type
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC

HP
1/2
1/2
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1
1
1
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2
2
2
2
2
2
3
3
3
3
3
3
5
5
5
5
5
7.5
7.5
7.5
7.5
7.5
10
10
10
10
10
15
15
15
20
20
20
25
25
25
25
30
30
30
30

Motor
P/N
159184
159184
159184
16077
16077
16077
105568
115860
115860
115860
20371
20371
20371
105569
174993
174993
174993
16080
16080
16080
105570
94347
94347
94347
101286
101286
101286
105665
105572
105572
158165
158165
158165
158166
111564
111564
159330
159330
159330
111571
111567
155048
155048
155048
158170
105842
158171
158171
158171
158172
105846
158173
158173
158173
158174
142443
142443
142444
142301
142301
142302
165321
165321
165321
165322
165323
165323
165323
165324

CODE 39 - Starter (line voltage) and Overloads
volt ph
Mfg No.
P/N
min max
GE #
P/N
120 1 CL00A310T-J 151146 5.50 8.50 RTA1-M 151192
208 1 CL00A310T-L 151150 2.50 4.10 RTA1-K 151190
240 1 CL00A310T-S 151147 2.50 4.10 RTA1-K 151190
208 3 CL00A310T-L 151150 1.90 2.70 RTA1-J 151189
240 3 CL00A310T-S 151147 1.90 2.70 RTA1-J 151189
480 3 CL00A310T-U 151148 0.65 1.10 RTA1-F 151186
575 3 CL00A310T-Y 151149 0.65 0.90 RTA1-F 151186
120 1 CL01A310T-J 151151 10.00 16.00 RTA1-P 151194
208 1 CL00A310T-L 151150 4.00 6.30 RTA1-L 151191
240 1 CL00A310T-S 151147 4.00 6.30 RTA1-L 151191
208 3 CL00A310T-L 151150 1.90 2.70 RTA1-J 151189
240 3 CL00A310T-S 151147 1.90 2.70 RTA1-J 151189
480 3 CL00A310T-U 151148 1.00 1.50 RTA1-G 151187
575 3 CL00A310T-Y 151149 0.65 1.10 RTA1-F 151186
120 1 CL01A310T-J 151151 10.00 16.00 RTA1-P 151194
208 1 CL00A310T-S 151147 5.50 8.50 RTA1-M 151192
240 1 CL00A310T-S 151147 5.50 8.50 RTA1-M 151192
208 3 CL00A310T-L 151150 2.50 4.10 RTA1-K 151190
240 3 CL00A310T-S 151147 2.50 4.10 RTA1-K 151190
480 3 CL00A310T-U 151148 1.30 1.90 RTA1-H 151188
575 3 CL00A310T-Y 151149 1.00 1.50 RTA1-G 151187
120 1 CL02A310T-J 151156 14.50 18.00 RTA1-S 151196
208 1 CL00A310T-L 151150 8.00 12.00 RTA1-N 151193
240 1 CL00A310T-S 151147 8.00 12.00 RTA1-N 151193
208 3 CL00A310T-L 151150 4.00 6.30 RTA1-L 151191
240 3 CL00A310T-S 151147 4.00 6.30 RTA1-L 151191
480 3 CL00A310T-U 151148 1.90 2.70 RTA1-J 151189
575 3 CL00A310T-Y 151149 1.30 1.90 RTA1-H 151188
120 1 CL04A310M-J 151165 21.00 26.00 RTA1-U 151198
240 1 CL01A310T-S 151152 10.00 16.00 RTA1-P 151194
208 3 CL00A310T-L 151150 5.50 8.50 RTA1-M 151192
240 3 CL00A310T-S 151147 4.00 6.30 RTA1-L 151191
480 3 CL00A310T-U 151148 2.50 4.10 RTA1-K 151190
575 3 CL00A310T-Y 151149 1.90 2.70 RTA1-J 151189
120 1 CL04A310M-J 151165 25.00 32.00 RTA1-V 151199
240 1 CL02A310T-S 151157 10.00 16.00 RTA1-P 151194
208 3 CL00A310T-L 151150 5.50 8.50 RTA1-N 151192
240 3 CL00A310T-S 151147 5.50 8.50 RTA1-N 151192
480 3 CL00A310T-U 151148 2.50 4.10 RTA1-K 151190
575 3 CL00A310T-Y 151149 2.50 4.10 RTA1-K 151190
240 1 CL04A310M-S 151166 17.50 22.00 RTA1-T 151197
208 3 CL01A310T-L 151155 14.50 18.00 RTA1-S 151196
240 3 CL01A310T-S 151152 10.00 16.00 RTA1-P 151194
480 3 CL00A310T-U 151148 4.00 6.30 RTA1-L 151191
575 3 CL00A310T-Y 151149 4.00 6.30 RTA1-L 151191
240 1 CL45A310M-S 151170 30.00 40.00 RTA1-W 151200
208 3 CL04A310M-L 151169 21.00 26.00 RTA1-U 151198
240 3 CL25A310T-S 151161 17.50 22.00 RTA1-T 151197
480 3 CL01A310T-U 151153 8.00 12.00 RTA1-N 151193
575 3 CL00A310T-Y 151149 5.50 8.50 RTA1-N 151192
240 1 CL06A311M-S 151172 30.00 43.00 RTA2-E 151206
208 3 CL04A310M-L 151169 25.00 32.00 RTA1-V 151199
240 3 CL04A310M-S 151166 21.00 26.00 RTA1-U 151198
480 3 CL01A310T-U 151153 10.00 16.00 RTA1-P 151194
575 3 CL01A310T-Y 151154 8.00 12.00 RTA1-N 151193
240 3 CL06A311M-S 151172 30.00 43.00 RTA2-E 151206
480 3 CL25A310T-U 151162 17.50 22.00 RTA1-T 151197
575 3 CL02A310T-Y 151158 10.00 16.00 RTA1-P 151194
240 3 CL07A311M-S 151175 42.00 55.00 RTA2-G 151202
480 3 CL04A310M-U 151167 25.00 32.00 RTA1-V 151199
575 3 CL25A310T-Y 151163 17.50 22.00 RTA1-T 151197
208 3 CL09A311M-L 151179 64.00 82.00 RT2-J 151204
240 3 CL07A311M-S 151175 54.00 65.00 RT2-H 151203
480 3 CL04A310M-U 151167 25.00 32.00 RT1-V 151199
575 3 CL04A310M-Y 151168 21.00 26.00 RT1-U 151198
208 3 CL10A311M-L 166756 78.00 97.00 RT2-L 151205
240 3 CL09A311M-S 151178 64.00 82.00 RT2-J 151204
480 3 CL06A311M-U 151174 30.00 43.00 RT2-E 151206
575 3 CL04A310M-Y 151168 25.00 32.00 RT1-V 151199

(continued)

Form P-RDF, Page 9

Blower Motors, Contactor, and Starters (cont'd)
Replacement Line Voltage Starters for RDF units manfuactured before 1996 (cont'd)
Type
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE
EE

HP
1
1
1
1
1 1/2
1 1/2
1 1/2
1 1/2
2
2
2
2
3
3
3
3
5
5
5
5
7 1/2

Motor
P/N
105659
159328
159328
158175
105662
159329
159329
158162
105664
159027
159027
158176
159186
159028
159028
159030
159029
159029
159029
111602
159331

CODE 39 - Starter (line voltage) and Overloads
volt ph
Mfg No.
P/N
min max
GE #
P/N
208 3 CL00A310T-L 151150 2.50 4.10 RTA1-K 151190
240 3 CL00A310T-S 151147 2.50 4.10 RTA1-K 151190
480 3 CL00A310T-U 151148 1.00 1.50 RTA1-G 151187
575 3 CL00A310T-Y 151149 1.00 1.50 RTA1-G 151187
208 3 CL00A310T-L 151150 4.00 6.30 RTA1-L 151191
240 3 CL00A310T-S 151147 2.50 4.10 RTA1-K 151190
480 3 CL00A310T-U 151148 1.90 2.70 RTA1-J 151189
575 3 CL00A310T-Y 151149 1.30 1.90 RTA1-H 151188
208 3 CL00A310T-L 151150 4.00 6.30 RTA1-L 151191
240 3 CL00A310T-S 151147 4.00 6.30 RTA1-L 151191
480 3 CL00A310T-U 151148 2.50 4.10 RTA1-K 151190
575 3 CL00A310T-Y 151149 1.90 2.70 RTA1-J 151189
208 3 CL00A310T-L 151150 8.00 12.00 RTA1-N 151193
240 3 CL00A310T-S 151147 5.50 8.50 RTA1-N 151192
480 3 CL00A310T-U 151148 2.50 4.10 RTA1-K 151190
575 3 CL00A310T-Y 151149 2.50 4.10 RTA1-K 151190
208 3 CL02A310T-L 151159 10.00 16.00 RTA1-P 151194
240 3 CL02A310T-S 151157 10.00 16.00 RTA1-P 151194
480 3 CL00A310T-U 151148 5.50 8.50 RTA1-M 151192
575 3 CL00A310T-Y 151149 4.00 6.30 RTA1-L 151191
208 3 CL04A310M-L 151169 21.00 26.00 RTA1-U 151198

Motor
CODE 39 - Starter (line voltage) and Overloads
Type HP
P/N
volt ph
Mfg No.
P/N
min max
GE #
P/N
EE 7 1/2 159332 240 3 CL25A310T-S 151161 17.50 22.00 RTA1-T 151197
EE 7 1/2 159332 480 3 CL00A310T-U 151148 8.00 12.00 RTA1-N 151193
EE 7 1/2 158164 575 3 CL00A310T-Y 151149 5.50 8.50 RTA1-N 151192
EE
10 159333 208 3 CL04A310M-L 151169 25.00 32.00 RTA1-V 151199
EE
10 159334 240 3 CL04A310M-S 151166 21.00 26.00 RTA1-U 151198
EE
10 159334 480 3 CL01A310T-U 151153 10.00 16.00 RTA1-P 151194
EE
10 158163 575 3 CL00A310T-Y 151149 10.00 16.00 RTA1-P 151194
EE
15 142440 208 3 CL06A311M-L 151173 30.00 43.00 RTA2-E 151206
EE
15 142441 240 1 CL06A311M-S 151172 30.00 43.00 RTA2-E 151206
EE
15 142441 480 3 CL25A310T-U 151162 17.50 22.00 RTA1-T 151197
EE
15 142289 575 3 CL02A310T-Y 151158 10.00 16.00 RTA1-P 151194
EE
20 159187 208 3 CL07A311M-L 151176 54.00 65.00 RTA2-H 151203
EE
20 142299 240 3 CL06A311M-S 151172 42.00 55.00 RTA2-G 151202
EE
20 142299 480 3 CL04A310M-U 151167 21.00 26.00 RTA1-U 151198
EE
20 142300 575 3 CL25A310T-Y 151163 17.50 22.00 RTA1-T 151197
EE
25 159031 208 3 CL09A311M-L 151179 64.00 82.00 RT2-J 151204
EE
25 159033 240 3 CL08A311M-S 151177 54.00 65.00 RT2-H 151203
EE
25 159033 480 3 CL04A310M-U 151167 25.00 32.00 RT1-V 151199
EE
30 159032 208 3 CL10A311M-L 166756 78.00 97.00 RT2-L 151205
EE
30 159034 240 3 CL09A311M-S 151178 64.00 82.00 RT2-J 151204
EE
30 159034 480 3 CL06A311M-U 151174 30.00 43.00 RT2-E 151206

CODE 40 - Replacement Parts for NEMA Starters - Apply to RDF Models MAnufactured prior to 10/92
NEMA Motor S tarters
Size Coil Voltage
0
24 Volt
1
24 Volt
2
24 Volt
3
24 Volt
4
24 Volt
0
115 Volt
0
208 Volt
0
230 Volt
0
460 Volt
1
115 Volt
1
208 Volt
1
230 Volt
1
460 Volt
2
208 Volt
2
230 Volt
2
460 Volt
3
208 Volt
3
230 Volt
3
460 Volt
3
575 Volt
4
208 Volt

GE#
CR306B024
CR306C024
CR306D024
CR306E024
CR306F024
CR306B002
CR306B023
CR306B003
CR306B004
CR306C002
CR306C023
CR306C003
CR306C004
CR306D023
CR306D003
CR306D004
CR306E023
CR306E003
CR306E004
CR306E004
CR306F023

Reznor P/N for
RDF-1 RDF-2 RDF-3
39919
39919
39919
39920
39920
39920
—
39921
39921
—
39922
39922
—
—
91519
111523
—
—
111524 111524
—
111525 111525
—
111522 111522 111522
111526
—
—
111499 111499
—
111521 111521
—
111527 111527
—
—
111528 111528
—
111529 111529
—
111530 111530
—
111531 111531
—
—
111533
—
—
111532
—
—
119852
—
—
111534

Holding Coils for NEMA S tarters
Size
Coil Voltage
GE#
0/1
24
15D21G024
0/1
115
15D21G002
0/1
208
15D21G023
0/1
230
15D21G003
0/1
460
15D21G004
0/1
575
15D21G005
2
24
15D22G024
2
208
15D22G023
2
230
15D22G003
2
460
15D22G004
3
24
55-501336G024
3
208
55-501336G023
3
230
55-501336G003
3
460
55-501336G004
4
24
55-501463G024
4
208
55-501463G023
Form P-RDF, Page 10

Reznor P/N
48531
48507
48509
73795
48512
73601
93957
111927
111928
111929
95093
111931
111933
111932
102816
111935

NEMA Open Motor
Starters

Starter
Heater

Holding
Coil

NOTE: Effective 10/90, motor starter coils were changed
to line voltage (For relay, see CODE 8, page 4)
Heaters for NEMA Starters
HP/Voltage/Phase
GE#
5/208/3
CR123C18.0B
5/230/3 and 10/460/3
CR123C16.3B
5/460/3
CR123C8.67A
5/208/3
CR123C19.8B
7.5/208/3
CR123C25.0B
7.5/230/3
CR123C22.8B
7.5/460/3
CR123C12.5B
10/208/3
CR123C33.0B
10/230/3
CR123C30.3B
10/460/3
CR123C137B
15/208/3
CR123F56.7B
15/230/3
CR123FC40.0B
15/460/3
CR123C21.4B
20/208/3 and 25/230/3
CR123F77.28B
20/230/3
CR123F65.8B
25/208/3 and 30/230/3
CR123F91.4B
25/460/3
CR123C36.6B
30/208/3
CR123F10.4C
30/460/3
FA30B
30/575/3
F327B

Reznor P/N
89941 or 110617
16193 or 110626
16192 or 110619
91542
16196
89924 or 110622
17257 or 110624
89947 or 110625
89949 or 110627
110623
91543
89933
19556
91544
91545
91546
16195
91547
119851
121175

Gas Regulators, Valves, and Pressure Switches
CODE Description
41 1" Pressure Regulator, RV53-88
42 Regulator, 1" manifold, 5 PSI to 6" w.c., Maxitrol R600S
42A Standard brown spring for propane gas (in CODE 42) for lower pressure range 1 - 3.5" w.c.
Std cadmium spring for natural gas (in CODE 42) for pressure range from 3.0 - 6.0" w.c., Maxitrol #R5310-36
Optional orange spring in CODE 42, for pressure range from 4.0 - 8.0" w.c., Maxitrol #R5310-48
43A Pilot Regulator, 3/8", Maxitrol #R400-S (replaced by CODE 43B)
43B Pilot Regulator, 3/8", Maxitrol 325-3 (functional replacement for 43A)
44A Pilot Valve, 110V, 3/8", G/C #S311AF02N6-CF5 (changed to 24V, CODE 44B, with units mfgd beginning 3/96)
44B Pilot Valve, 24V, 3/8", G/C #S3111AF02N6-CF5 (used from 3/96 to 9/03)
44C Pilot Valve, 24V, 3/8", M/H V8046C1030 (on units manufactured beginning 9/03)
45A Pilot Needle Valve, Nupro B-4JNR (on units mfgd from 1/91 through 1/96)
45B Pilot Needle Valve Conversion Kit (includes all parts needed to add pilot needle valve and change regulator
on RDF Models manufactured prior to 1/91)
46A Solenoid Valve, 1", 120V, G/C #K3A562T (changed to 24V, CODE 46B, with units mfgd beginning 3/96)
46B Solenoid Valve, 1", 24V, G/C #K3A661T (on units mfgd prior to Series 3, 9/03)
47 1-stage Gas Valve, M/H VR8404M5569, Natural or Propane, 1" Used in Gas Control Option AG1 available on
48 Air Controller, 40-100°F (used as a ductstat)
RDF Series 3 (manufactured beginning 9/03)
Used in Gas Control Option AG3 available on
49 2-stage Gas Valve, M/H V8944B-1126, Natural, 1"
50 2-stage Ductstat, T678A1015, 60-110°F
RDF Series 3 (manufactured beginning 9/03)
51 Mechanical Modulation Gas Valve, V5155-2548, 1", 40-120°F
Used in Gas Control Option AG50

CODE 41 -Regulator,
P/N 123950, Maxitrol
RV53-88

CODE 44A - Pilot Valve,
P/N 86967, 110V, G/C
#S311AF02N6-CP5

CODE 46A Solenoid
Valve,
P/N 86966,
G/C
#K3A562,
120V

CODE 46B Solenoid
Valve,
P/N 146472,
G/C
#K3A661T,
24V

CODE 42 Regulator,
P/N 86964,
Maxitrol
R600S
CODE 42A Regulator Spring
for CODE 42
CODE 44B Pilot Valve,
P/N 145733,
24V, G/C
#S311AF02N6CF5
CODE 44C - Pilot
Valve, P/N 204769,
M/H V8046C1030,
24V

Components in Gas
Control Option AG1
CODE
47 - P/N
159743,
1-Stage
Gas
Valve

CODE 48 P/N 126170,
Conroller

CODE 43A - Pilot Regulator,
P/N 86965, Maxitrol R400S
(on units manufactured prior to
1/91; replaced
by CODE 43B)

CODE45A - Pilot
Needle Valve, P/N
112462, Nupro
#B-4JNR (on
units manufactured between
1/91 and 3/96)

Components in Gas
Control Option AG3
CODE 49 P/N
203866,
2-Stage
Gas
Valve

P/N
123950
86964
91787
97196
97351
86965
112644
86967
145733
204769
112462
112645
86966
146472
159743
126170
203866
41700
203868

CODE 43B - Pilot Regulator,
P/N 112644, Maxitrol 325-03
(on units manufactured
beginning 1/91) a functional
replacement
for CODE 42A

CODE 45B
- Pilot
Needle
Valve
Conversion
Kit, P/N
112645, for
units
manufactured
before 1/91

Regulator,
P/N 112644

Brass
Elbow,
P/N 93388
Needle Valve and
Tubing, P/N 112710

CODE 51 - P/N 203868,
Mechanical Modulation Valve,
M/H V5115B-2548, in Gas
Control Option AG50

CODE 50 P/N 41700,
2-Stage
Ductstat

Form P-RDF, Page 11

Gas Regulators, Valves, and Pressure Switches (cont'd)
CODE
52A

52B
53
54
55
56
57
58
59A

59B

60
61

62

RDF Model
1-65 2-80 2-120 3-180 3-260
Valve only, 1" fluid power, Honeywell #V5055A1004
86992
Valve only, 1-1/4" fluid power, Honeywell #V5055A1012
N/A N/A N/A
N/A
89356
Valve only, 2" fluid power, Honeywell #V5055A1038
N/A N/A N/A
N/A N/A
N/A
91079
Actuator only, 120V, fluid operated, Honeywell #V4055A1007
86993
Vent Valve, 3/4" G/C #S262
86996
Vent Valve, 1" G/C #S262A02N3FJ5
N/A N/A N/A
N/A N/A
N/A
91084
Used on RDF Series 3 (both
Low Gas Pressure Switch, automatic
204375
High Gas Pressure Switch, manual reset
204297
include built-in vent limiter )
Low Gas Pressure Switch, Antunes #RLGP-A Used on RDF prior to Series 3
93849
High Gas Pressure Switch, Antunes #HGP-AMI
93850
(9/03)
Vent Limiter, Maxitrol #12A09
123481
Manual Gas Valve, 1", Conbraco #50-4031
30257
Manual Gas Valve, 1-1/4", Conbraco #50-503-02
N/A N/A N/A
N/A
89350
Manual Gas Valve, 2", Conbraco #50-703-02
N/A N/A N/A
N/A N/A
N/A
91072
159725, 1" Valve & 110758, 1" Ball Valve Adapter
Gas Valve, Watts B-6000-UL-TH, with ball valve adapter, used on units mfgd
159729, 1-1/4" Valve & 110759, 1-1/4" Ball Valve Adapter
beginning 7/90 replacing CODE 59A valves
159735, 2" Valve & 110760, 2" Ball Valve Adapter
Manual Pilot Gas Valve, 3/8"
159720
Gas Control Regulator, 1", Maxitrol M611 R-88
87001
Gas Control Regulator, 1-1/4", Maxitrol MR212D
N/A N/A N/A
N/A
89351
Gas Control Regulator, 2", Maxitrol MR212E
N/A N/A N/A
N/A N/A
N/A
91071
x 1" NPT (Same as Option CZ1)
124258
Gas Supply Regulator Kit, 5 psi
1-1/2" x 1-1/2" NPT (Same as Option CZ2)
124259
Description

1-20

CODE 53 - Vent Valve
3/4", P/N 86996, G/C
#S262; 1", P/N 91084,
G/C S262A0N3FJ5

CODE 52B

CODE 52A
(used with
CODE 52B)

Serial No.
Size
Gas
P/N
Code
J2, J3, J4
1" N or P 86992
K2
1-1/4" N or P 89356
Part of Serial No.
K4
2" N or P 91079

1-40

1-50

Gas Pressure Switehes - on RDF Series 3
(manufactured beginning 9/03)
CODE 54 - Low Gas CODE 55 - High Gas
Pressure Switch
Pressure Switch
(manual reset),
(automatic),
#C6097B1028,
#C6097A1053,
P/N 204297
P/N 204375

Valve codes J2,
J3, J4, K2 and K4

Gas Pressure Switehes - prior to Series 3
(9/03)
CODE 56 - Low Gas
Pressure Switch,
P/N 93849, Automatic Reset,
Settings - 50% of minimum
inlet gas pressure as stated
on the unit rating plate
CODE 57 - High Gas
Pressure Switch,
P/N 93850, Manual Reset,
Settings - 125% of normal
manifold gas pressure as
stated on the unit rating plate

P/N 87001,
1", Maxitrol
M611 R-88

CODE 58 - Vent Limiter used with
Pressure Switches, P/N 123481
CODE 59B - Valve and
Adapter with Test Port

Valve

Adapter

Form P-RDF, Page 12

CODE 61 Gas Control
Regulators

CODE 60 Pilot Gas Valve,
P/N 159720

CODE 62 - Gas
Regulator Kit,
outlet pressure
range 1-12"
(maximum 5 psi)

P/N 89351,
1-1/4",
Maxitrol
MR212D

P/N 91071,
2", Maxitrol
MR212E

P/N 124258 (Same as Option CZ1),
Kit includes Maxitrol 1"x1" NPT
regulator
P/N 124259 (Same as Option
CZ2), Kit includes Maxitrol
1-1/2"x1-1/2" NPT regulator

Modulating Gas Controls
CODE
70

71
72

73
74

75

Description

In Gas Control
Option
AG30, AG31
AG32

Serial No.
Suffix
MV-7
MV-8

AG33

MV-9

Temperature Sensor, Maxitrol Series 14, #TS114
Temperature Sensor, Maxitrol Series 14A, #TS114A
Temperature Sensor, Maxitrol Series 44, #TS44E, 120°F max
Temperature Sensor, Maxitrol Series 44, #TS44C, 140°F max
Temperature Sensor, Maxitrol Series 94, #TS194A
Temperature Sensor, Maxitrol Series 14E, #TS394-2B-4
Temperature Sensor, Maxitrol Series 14E, #TS194Q
Mixing Tube, Maxitrol MTI-12
Amplifier, Maxitrol Series 14 & 14A, #A1014L
Amplifier, Maxitrol Series 44, #A1044EL, 120°F maximum
Amplifier, Maxitrol Series 44, #A1044CL, 140°F maximum
Amplifier, Maxitrol Series 94, A1494
Amplifier, Maxitrol Series 14E, ADFM14
Amplifier, Maxitrol Series 44E-21 & 44ER-21, ADFM44
Signal Conditioner, Maxitrol
Temperature Selector, Maxitrol Series 14, #TD114

AG33

MV-9

AG36
AG47
AG48, AG51
AG37
AG30, AG31

MV-B
MV-D
MV-E, MV-F
MV-C
MV-7

Temperature Selector, Maxitrol Series 14A, #TD114A
Temperature Selector, Maxitrol Series 14E, #TDDFM14
Selectrastat (temperature selector), Maxitrol Series 44, #T-244
Temperature Selector, Maxitrol Series 44E, #TDDFM44
Temperature Selector, Maxitrol Series 94, #TD294E-609-0818

AG32
AG47
AG33
AG48, AG51
AG36

MV-8
MV-D
MV-9
MV-E, MV-F
MV-B

Overriding Thermostat, Series 14, #T115

AG 30, 31, 32

MV-7, MV-8

CODE 70 Temperature
Sensor

AG36
MV-B
MV-D, MV-E,
AG47, AG48,
MV-F
AG51
All above
AG 30, 31, 32
MV-7, MV-8

P/N 90324, Maxitrol #TS114;
P/N 87106, Maxitrol #TS114A (illustrated);
P/N 119617, Maxitrol #TS44E;
P/N 194160, Maxitrol #TS44C;
P/N 133228, Maxirol TS194A;

Location

P/N

Discharge
Discharge

90324
87106
119617
Discharge
194160
Discharge
133228
204452
Outside & Return Air
Discharge
204453
Same as above
90323
148590
157915
Electrical Control
194159
Compartment (See
133229
204454
page 3.)
204450
134170
86988 (U.S.A.)
Remote
101165 (Canada)
Remote
87107
Remote
204455
Space
86990
Remote
204451
133230, 120°F
Remote
159287, 160°F
Space
24857

P/N 204452, Maxitrol #TS394-2B-4;
P/N 204453, Maxitrol #TS194Q
(illustrated)

IMPORTANT NOTE: When replacing a temperature sensor on a Maxitrol MV-9 system (Option AG33), check the Model No. on the
sensor.. P/N 119617 or 194160 is used on units manufactured beginning 2/92; P/N 87041 is used on units manufactured prior to 2/92.
Sensors are not interchangeable; the sensor MUST match the amplifier.

CODE 72 - Amplifier (Amplifiers are not interchangeable and must match the temperature sensor.)
P/N 148590,
P/N
Maxitrol
204454,
#A1014L
Maxitrol
(replaces
#ADFM14
P/N 86976)
P/N 194159, Maxitrol #A1044CL;
P/N 157915, Maxitrol #A1044EL
(replaces P/N 119616);
P/N 86989, Maxitrol #A1044 (on
systems mfgd prior to 2/91)

P/N 133229,
Maxitrol A1494

CODE 74 - Temperature Selectors (see chart for option application)
P/N 86988, TD114 U.S. Models, Range 55-90°F
P/N 101165, TD114, Canadian Models, Range 50-75°F;
P/N 87107, TD114A, Range 80-130°F;
P/N 123943, TD114B, Range 120-170°F
P/N 204455, TD DFM14;
P/N 204451, TD DFM44

P/N 86990,
Selectrastat
Maxitrol T-244

P/N 204450, Maxitrol
#ADFM44

CODE 71
- Mixing
Tube,
P/N
90323
CODE 73 - Maxitrol
Signal Conditioner,
P/N 134170
(for computer control)

P/N 133230, Maxitrol #TD294E- CODE 75 - P/N
24857, Maxitrol
609-0818, Dual Temperature
#T115
Selector for Paint Booth
Application, Option AG36

Overriding
Thermostat,
Option AG33
Form P-RDF, Page 13

Ignition System - Hot Surface Ignition
Ignition system changed from spark to hot surface beginning 3/96.

Description of Parts of Hot Surface Ignition System and Conversion Kits
CODE
Located in
80A Hot Surface Ignition Module, RAM #H4MC24-01- applies to RDF systems manufactured from
the
3/96 to 9/03 (prior to RDF Series 3) - Serial No. Ignition System Code 72
electrical
80B Hot Surface Ignition Module, Synetek FC-IH1040B, single flame rod (Used on RDF Series 3 with
control
burner sizes from 250-1500 MBH, Options BL1-BL6) - Serial No. Ignition System Code 82
compart80C Hot Surface Ignition Module, Synetek FC-IH1040C, dual flame rod (Used on RDF Series 3 with
ment.
burner sizes from 1750-3000 MBH, Options BL7-BL13) - Serial No. Ignition System Code 81
81 Pilot Assembly for Hot Surface Ignition prior to RDF Series 3 (9/03)
including: Pilot
Pilot and
Flame
Flame Sensor, J/C #Y75MK-1D
Ignitor
Sensor
Screw, #8-1/2" long
Pilot bushing
Hex head cap screw, #10-32x3/8" lg
Hot Surface Ignitor, Norton #401E
Pilot, Sensor, and Ignitor for Model RDF Series 3
82A Pilot for RDF Series 3, 250-1500 MBH
82B Pilot for RDF Series 3, 1750-3000 MBH
83 Hot Surface Ignitor, Norton #401E
84 Flame Sensor, J/C #Y75MK-1D (Note: CODE 84 is for replacement of the flame sensor at the ignitor end of the
burner only. 1750-3000 MBH burners have a second flame sensor. For replacement, see CODE 99.)
85 Ignition Conversion Kit from Spark Pilot with for unit with a 200VA transformer
either a rectification type (CODE 94) or
for 115V unit with an 80VA transformer
ultraviolet flame (CODE 95) sensor to hot
for 208V unit with an 80VA transformer
surface ignition.
for 240V, 480V, or 575V unit with an 80VA transformer

CODE 80A, P/N 157953, Hot Surface
Ignition Module, RAM H4MC24-01

CODE 80B, P/N 204376, Hot Surface
Ignition Module, Synetek FC-IH1040B,
for burner with a single flame rod

204376
204166
120048
122840
134706
38529
121730
90167
121865
127910
122840
121865
134706
146268
146318
146319
146320

CODE 80C, P/N 204166, Hot Surface
Ignition Module, synetek FC IH1040C,
for burner with a double flame rod

Pilot, Hot Surface Ignitor,
and Flame Sensor on RDF
Series 3 Burner
Loc
ati
( n o on
sho t
wn)

CODE
82

CODE
84
CODE
83

Form P-RDF, Page 14

P/N
157953

Ignition System - Spark Ignition System (discontinued 3/96)
Description of Components of Spark Ignition System (Discontinued
on units beginning 3/96. See conversion kits in CODE 85, page 13.)
86 Flame Sensor Safety Relay, Rectification, Honeywell
With
#RA890F1270
Code
87 Flame Sensor Safety Relay, Rectification, Honeywell #R7795B93
1009 (less CODE 80)
With
88 Flame Sensor Safety Relay, Ultraviolet, Honeywell
Code
89 Flame Sensor Safety Relay, Ultraviolet, Honeywell #R7795A94
1009 (less CODE 90)
90 Prepurge Timer Board (prepurge relay), M/H ST795A-1031 (used in
CODES 87 and 89)
91 Subbase only used with CODES 87 (P/N 89407) & 89 (P/N 89436) ,
Honeywell #Q795A-1004
92 Subbase only used with CODES 86 (P/N 86972) & 88 (P/N 89409),
Honeywell #Q270A-1024
93 Flame Probe, Auburn #AA67-7892-1 (std on units mfgd before 9/88;
used w/CODE 84 or 85)
94 Ultraviolet Minipeeper Detector, Honeywell #C7027A (std on units
from 9/88 -2/96; optional on prior units; used with CODE 88 or 89)
RDF 1-20, 40, 50, 65
95 Flame Rod
RDF 2-80, 120
Wire
RDF 3-180, 260
Assembly
95A Housing only for Flame Rod Wire Assy, AMP #1-48016-0
RDF 1-20, 40, 50, 65
96 Ignitor
RDF 2-80, 120
Wire
RDF 3-180, 260
Assembly
97A Spark Plug, Auburn #27750 I-31, Maxon #18075
97B Spark Plug, #23539 Sapco 14mm (used prior to CODE 97A)

CODE

CODE 95,
Flame Rod
Wire Assy for
Spark Ignition
System
Housing only, P/N 19127

CODE 96,
Ignitor
Wire Assy
for Spark
Ignition
System

P/N

Flame Sensor Safety Relays and Subbases
for Spark Ignition System

86972
89407
89409
89436

Codes 87 and 89

Codes 86 and 88
89408
89410
86973
87937
89411
87904
89614
113952
19127
87906
89627
91362
87936
179342

CODE 90,
P/N 89408

CODE 91,
P/N 89410

CODE 92,
P/N 86973

CODE 93, P/N 87937, Flame Probe (std on
units with date codes from AJH to ANH)

CODE 94, P/N 89411,
Ultraviolet Detector
(std on units with date
codes from ANI to AVB;
optional on prior units)

Spark Plug for Spark Ignition System
CODE 97A, P/N 87936
(illusrated)
CODE 97B, P/N 179342, #23539 Sapco
14mm (used prior to CODE 97A)

Burners for RDF Series 3 (manufactured beginning 9/03)
RDF Series 3 systems use Midco HMA-700 Series
Burners. The Burner P/N listed below includes the burner,
the mixing plates, and the end plate. 1750-3000 MBH (4260") burners also include CODES 99 & 100.

Burner

CODE 98 - Model RDF Series 3 BURNER
Length
MBH
P/N
6" Burner
250
203312
12" Burner
500
203313
18" Burner
750
203314
24" Burner
1,000
203315
30" Burner
1,250
203316
36" Burner
1,500
203317
42" Burner
1,750 or 2,000
203318
48" Burner
2,250
203319
54" Burner
2,500
203320
60" Burner
2,750 or 3,000
203321
CODE 99 - Second Sensor (at the end of
the burner opposite the ignitor)
100
on 42-60" Burners, P/N 210766
CODE 100 - Holder
for CODE 99,
99
P/N 210767

Mixing Plates

Burner End Plate

CODE 83 Ignitor
CODE 82 - Pilot
Gas Supply Assembly
Form P-RDF, Page 15

Burners for RDF Systems manufactured prior to Series 3 (9/03)
CODE Replacement Burners (burners include cast iron burner and stainless steel mixing plates)
Size
BTU
Burner only by size
Replacement burner assembly only
for all burner assemblies
with inlet end for units with a spark ignition system
(does not include end plates, order CODE 102B)
101
6" Burner
250,000
123405
145757
Mixing Plates
12" Burner
500,000
123665
145758
18" Burner
750,000
123684
145759
24" Burner
1,000,000
123696
145760
30" Burner
1,250,000
123700
145761
36" Burner
1,500,000
145140
145762
42" Burner
1,750,000
145159
145763
48" Burner
2,000,000
145162
145764
54" Burner
2,250,000
145169
145765
60" Burner
2,500,000
145172
145766
Inlet end enclosure for spark ignition is
66" Burner
2,750,000
145175
145767
different from currently manufactured
Cast Iron
72" Burner
3,000,000
145178
145768
burner assemblies.
Burner
101A Replacement burner mixing plate only, 6" section, for all of the burners listed
above. Refer to Operation/ Maintenance/Service, Form O-ADF/DV/RDF, Burner
Cleaning, for instructions on burner service.
102A Burner End Plate only for HOT Surface Ignition
102B Burner End Plate only for Spark Ignition
103 Adjustable "mirror" to view burner and pilot flame through viewport on control
side of cabinet (on units manufactured beginning 3/92) - complete assembly
Components: Reflecting mirror only
Bracket assy including swivel ball joint
Swivel ball joint only
Mirror support only (attaches to cabinet)

Installed Burner Assembly

101A

P/N 116104, Maxon P/N 20580
Total quantity of plates per burner size, 6"-2; 12"-4"; 18"-6; 24"-8;
30"-10; 36"-12; 42"-14; 48"-16; 54"-18; 60"-20; 66"-22; 72"-24
(2) P/N 95473 - For all sizes of heaters and burners
(2) P/N 102957 - For all sizes of heaters and burners
P/N 119480 - Sizes 1-20 - 1-65; P/N 119481 - Sizes 2-80 - 3-260
P/N 116212 - All Sizes
P/N 119483 - All Sizes
P/N 119115 - All Sizes
P/N 119360 - Sizes 1-20-1-65; P/N 116210 - Sizes 2-80 - 3-260

CODE 103 - Pilot/Burner
Mirror Assembly

12" Burner
CODE 102A - Burner End
Plate showing the hot surface
ignition system
Hot surface ignition is standard
with units manufactured
beginning 3/96; for ignition
conversion kit see CODE 85,
page 13.
Pilot and Ignitor Assembly,
See CODE 81, page 13
Burner Inlet Flange,
P/N 123449, (must be sealed
with key graphite paste,
P/N 146269)
CODE 102B Burner End
Plate for burner
with spark
ignition,
P/N 102957

Form P-RDF, Page 16

Instructions to install pilot/burner mirror assembly on RDF units
manufactured prior to 3/92.
All Sizes (requires two #10 x 1/2" sheet metal screws) - (1) Turn off gas and power.
(2) Remove the burner door panel on the side of the unit opposite the controls. (3)
Remove the burner control door panel.
RDF 1 - (1) On the side of the unit opposite the controls, position the mirror on the
center post inner liner (refer to drawing on page 5, inner liner of CODE 12) so that
the bottom of the mirror is slightly higher than the top of the burner. (2) Mark and
drill two 1/8" holes.
RDF 2 and 3 - On the side of the unit opposite the controls, locate the two small
holes on the horizontal surface of the air deflector (aka return air damper support).
All Sizes - (1) Attach the mirror assembly with field-supplied sheet metal screws.
(2) On the back of the mirror support bracket, tighten the ball joint (swivel) bolt
head. (3) Adjust the mirror so that the burner and the pilot are visible when looking
through the viewport in the burner control panel. (4) Close the door panels.

Dampers and Controls
RDF Series 3
(units
Discharge Dampers
manufactured
Options AQ 3, 4;
AR 19, 20, 33, 36
beginning
9/03)
Bypass Dampers
Options AR 19, 20, 22,
23, 33, 34, 35, 36, 37
Return Dampers
Options AR 22, 23, 34, 37
AR 20
or 23
AR22
AR23
AR
19
Remote Pressure Null or 22
Switch, CODE 33, page 6. Remote Potentiometer, CODE 32, page 6.
Options AR 36 and 37 have a Remote Photohelic Pressure Sensor, CODE 34, page 6.

Dampers in RDF Series 3 (units manufacturered beginning 9/03)
Code Description
110 Bypass Damper

In Option
RDF-1
AR 19, 20, 22, 23,
203602 - 26" x 12"
33, 34, 36, 37
111 Return Air Damper AR 22, 23, 34, 37
203602 - 26" x 12"
112 Discharge Damper AQ 3, 4; AR19, 20,
15869 - 21-1/8" x 18-1/2"
33, 36

RDF-2

RDF-3

203604 - 53-1/2" x 17-3/4"

203603 - 65-3/4" x 20"

203604 - 53-1/2" x 17-3/4"

203603 - 65-3/4" x 20"

89355 - 27-1/4" x 27-1/4"

91073 - 37" x 37"

Damper Motors and Linkages in RDF Series 3 (units manufacturered beginning 9/03)
CODE Description/Damper Arrangement
2-Position, 100% Makeup Air
115
Variable Air Volume with Manual Potentiometer (CODE 32,
116
page 6)
117 Discharge Variable Air Volume with Automatic Pressure Switch (CODE
Damper
33, page 6)
Variable Air Volume with Computer Control through Signal
118 Motor
Conditioner (CODE 73, page 13)
Variable Air Volume with Photohelic Pressure Sensor (CODE
119
34, page 6)
Variable Air Volume
120 Bypass
Damper
Motor
Return Air with Manual Potentiometer (CODE 32, page 6)
121
Return Air with Automatic Pressure Switch (CODE 33, page 6)
122
Return Air
Variable Air Volume with Computer Control through Signal
123
Damper
Conditioner (CODE 73, page 13)
Motor
Variable Air Volume with Photohelic Pressure Sensor (CODE
124
34, page 6)
125 Damper Crank Arm, M/H #26026K
126

Ball Joint, M/H 27518

127

Damper Crank Arm Kit, J/C #9000-153

128
129

Damper Crank Arm, W/R 135-0007
Damper Crank Arm, W/R 135-0002

In Option
AQ3, AQ4

RDF-1 RDF-2 RDF-3
159892, J/C M9216-BGC-2

AR19

204269, J/C M9216-JGA-2

AR20

204270, J/C M9109-AGA-2

AR33

204271, J/C M9216-GGC-2

AR36

204270, J/C M9109-AGA-2

AR 19, 20, 22, 23,
33, 34, 36, 37

204268, J/C M9108-AGD-2

AR22
AR23

204269, J/C M9216-JGA-2
204270, J/C M9109-AGA-2

AR34

204271, J/C M9216-GGC-2

AR37

204270, J/C M9109-AGA-2

(1) AR 22, 23, 34
(1) AQ 3, 4
(2) AR19, 20, 22,
23, 34, 37
(2) AQ 3, 4
(1) AR 22, 23;
(1) AQ 3
(1) AR 34, 37
(1) AQ 3, 4
(1) AQ 4

--

12635
12635

--

12636
12636

--

194200
194200

--

66278
---

66278
66277

Form P-RDF, Page 17

Dampers and Controls (cont'd)
RDF Series 3 (units manufactured beginning 9/03) (cont'd)
CODE 115 2-Position Damper
Motor, J/C M9216BGC-2,
P/N 159892

Modulating Damper Motors (See Chart on page 16 for application.)

CODES 116, 121 Discharge or Return
Air Damper Motor,
J/C M9216-JGA-2,
P/N 204269
CODE 125, Damper
Crank Arm, P/N 12635,
M/H #26026K

CODES 117, 119, 122,
144, Discharge or
Return Air Damper
Motor, J/C M9109AGA-2, P/N 204270

CODE 126, Ball
Joint, P/N 12636,
M/H #27518

CODE 120 - Bypass
Damper Motor, J/C
M9108-AGD-2,
P/N 204268

CODE 127, Damper
Crank Arm Kit, P/N
194200, J/C #9000-153

CODES 118, 123 Discharge or Return
Air Damper Motor,
J/C M9216-GGC-2,
P/N 204271

CODE 128, Damper
CODE 129, Damper
Crank Arm Kit, P/N
Crank Arm Kit, P/N
66278, W/R 135-0007 66277, W/R 135-0002

CODE 130 - Damper Rods in RDF Series 3 (units manufactured beginning 9/03)
Damper Arrangement
Discharge, 2-Position, 100% Makeup Air (Vertical)
Discharge 2-Position, 100% Makeup Air (Horizontal)
Return Air Damper

Options
AQ3
AQ4
AR34, 37

RDF-1
RDF-2
RDF-3
112555 - 1/4" x 16" 89640 - 1/4" x 7-1/2" 89640 - 1/4" x 7-1/2"
112555 - 1/4" x 16"
89970 - 1/4" x 38"
91428 - 1/4" x 24"
--5120, 1/4" X 7-7/8"

Dampers and Controls
RDF Systems prior to Series 3 (manufactured before 9/03)
Control and Damper Locations
KEY:
1 - Burner
2 - Discharge Damper Motor (Options AR19 & 20)
3 - Discharge Damper (Options AR19 & 20)
4 - Manual Reset Limit
5 - Automatic Limit
6 - Discharge Air Sensor
7 - Blower Motor
8 - Damper Motor (Optional)
9 - Return Air Damper (Options AR22 & 23)
10 - Bypass Damper (Options AR19, 20, 22 & 23)

Sizes 2-80, 2-120,
3-180, 3-260

Outside
Air
Hood

Sizes 2-80, 2-120,
3-180, 3-260

Dampers in RDF Systems prior to Series 3 (9/03)
Code Description In Option
AR 19, 20,
140 Bypass
22, 23
Damper
Return Air AR 22, 23
Damper
141 Discharge AQ 3, 4;
Damper
AR19, 20
142 Bypass
Damper
AR 22, 23
Adjustment
Arm
Form P-RDF, Page 18

RDF-1
87117 32"x10"
87117 32"x10"
86999 22"x18"

RDF-2
89354 22"x54"
89354 22"x54"
89355 28"x28"

In the Electrical Compartment -Sizes 1-20, 1-40,
1-50, 1-65

RDF-3
91074 30"x68"
91074 30"x68"
91073 37"x37"

111309 111309 111309

Dampers and Controls (cont'd)
RDF Systems prior to Series 3 (manufactured before 9/03) (cont'd)
Damper Motor and Accessories by Damper Arrangement and Option
CODE Description/Damper Arrangement
143 Motor Discharge, 2-Position, 100% Makeup Air
144 Motor Discharge, Variable Air Volume with
Manual Potentiometer (CODE 33, page 6)
145 Motor Discharge, Variable Air Volume with
Automatic Pressure Switch (CODE 34,
page 6)
146 Motor Bypass, Variable Air Volume

In Option
AQ3, AQ4

RDF-1
87000
M/H M8415A1004

RDF-2

RDF-3
97385
W/R 3402-9

115681*
M/H M9175A1015 (replaces 53928)
115683*
87116

AR19
AR20

M/H M6414A1009

M/H M6194B1011 (replaces 87059)

115683*
M/H M6194B1011 (replaces 87059)
115681*
M/H M9175A1015 (replaces 53928)
115683*
87116
M/H M6414A1009
M/H M6194B1011 (replaces 87059)
113963
113963

AR19, AR20, AR22,
87116
AR23
M/H M6414A1009

147 Motor Return Air with Manual Potentiometer
AR22
(CODE 33, page 6)
148 Motor Return Air with Automatic Pressure
AR23
Switch (CODE 34, page 6)
149 Auxiliary End Switch only for M/H damper motors, M/H Q607B1067
150 Damper Crank Arm, M/H #26026K -used in all
(2) AR19,20,22,23;
12635
12635
damper arrangements
(1) AQ3,4
(4) AR19,20,22,23;
151 Ball Joint, M/H 27518 -used in all damper
12636
12636
(2) AQ3,4
arrangements
116209*
(2) AR19,20,22,23
152 Damper Motor Crank Arm, M/H 221455A
116209*
20874
Damper Motor Crank Arm & Clip, M/H 7616BR(used w/obsolete mtrs)
20874
*When installing motors P/N 115681 or 115683 to replace P/N 53928 or 87059, it is necessary to change the motor crank arm. Order P/N
116209.

CODE 143 - Damper Motor for 2-Position
Discharge Damper, 100% Makeup Air
(Options AQ3 and AQ4)

P/N 87000, M/H
#M8415A1004, used on
RDF 1

P/N 97385, W/R
#3402-9, used on
RDF 2 & 3

Codes 144 and 147 Modulating Damper
Motor,
P/N 115681,
M/H M9175A1015, used
in Options AR19 and
AR22 on RDF 1, 2 & 3
CODE 149 - Auxiliary
End Switch, P/N
113963,
M/H Q607B1067

Codes 145, 146 and 148 - Modulating Damper Motor used for the
discharge damper in Option AR20; for the bypass damper in Options
AR19, 20, 22, and 23; and for the return air damper in Option AR23

P/N 87116, M/H #M6414A1009,
used on RDF 1
CODE 150 Damper Crank
Arm, P/N 12635,
M/H #26026K

P/N 115683, M/H #M6194B1011
used on RDF 2 & 3
CODE 151 - Ball
Joint, P/N 12636,
M/H #27518

CODE 152 - Damper Motor Crank Arms
P/N 116209, M/H 221455A,
used in Options AR19, 20, 22,
and 23 (required when
replacing obsolete motors; see
note on page 16.)

P/N 20874, M/H
7616BR, motor crank
arm used with obsolete
motor P/N's 53928
and 87059

CODE 153 - Damper Rods (Damper rods may require being cut to desired length.)
Damper Arrangement
Discharge 2-Position, 100% Makeup Air (Horizontal)
Discharge, 2-Position, 100% Makeup Air (Vertical)
Discharge, Variable Air Volume with Potentiometer
Discharge, Variable Air Volume with Pressure Sensor
Bypass, Variable Air Volume and Return Air
Return Air with Potentiometer
Return Air with Pressure Sensor

Options
AQ4
AQ3
AR19
AR20
AR19,20,22,23
AR22
AR23

RDF-1
11560 - 1/4" x 16"
11560 - 1/4" x 16"
11560 - 1/4" x 16"
11560 - 1/4" x 16"
5120 - 1/4" x 7-7/8"
11560 - 1/4" x 16"
11560 - 1/4" x 16"

RDF-2
89970 - 1/4" x 38"
89640 - 1/4" x 7-1/2"
14226 - 1/4" x 11"
14226 - 1/4" x 11"
90056 - 1/4" x 5"
14226 - 1/4" x 11
14226 - 1/4" x 11

RDF-3
91428 - 1/4" x 24"
89640 - 1/4" x 7-1/2"
91428 - 1/4" x 24"
91428 - 1/4" x 24"
89640 - 1/4" x 7-1/2"
91422 -1/4" x 18-1/2"
91422 -1/4" x 18-1/2"
Form P-RDF, Page 19

Remote Console
Note: Console height changed 10/01. Console parts listed are currently manufactured size.
NOTE: A remote console was standard with RDF Models manufactured prior to 9/03. Beginning with RDF Series 3 (units
manufactured beginning 9/03), the remote console is an option.

162

161
164

163

Replacement Components
CODE
160
161
162
31, page 6
32, page 6
74, page 13

Description
P/N
Remote Console Box 10-9/16" x 7-1/4" x 2-5/8"
107010
Remote Console Box 15-9/16" x 7-1/4" x 2-5/8"
107011
Mounting Ring for 10-1/16" long box
107014
Mounting Ring for 15-1/16" long box
107015
Light with red lens, Solico #5TD1L-R-B5
101889
Bushing for installing light above on old-style console
106747
DPDT Switch, Cutler Hammer #7561K6
101900
Potentiometer, Honeywell 112894FA
16110
Temperature Selector, Option AG30, AG31
86988 or 101165
Temperature Selector, Option AG32
87101
Temperature Selector, Option AG33
86990
Temperature Selector, Option AG47
204455
Temperature Selector, Option AG48, AG51
204451

CODE 160 - Console Box

Technical Data of the Remote Console (Variations depend on options selected; consult
custom wiring diagram for controls and to determine wiring required.)
Dimensions (inches)
Temperature
Control Qty of
Potentiometer
Selector or
Switch Lights*
***
L**** H**** D
Sensor **
1-5

Yes
3
Yes
No
10-13/16 7-3/8 2-5/8
Yes
3
No
No
10-13/16 7-3/8 2-5/8
Yes
3
Yes
Yes
15-13/16 7-3/8 2-5/8
Yes
3
No
Yes
10-13/16 7-3/8 2-5/8
Yes
4
Yes
No
15-13/16 7-3/8 2-5/8
Yes
4
No
Yes
15-13/16 7-3/8 2-5/8
Yes
4
Yes
Yes
15-13/16 7-3/8 2-5/8
Yes
4
No
No
15-13/16 7-3/8 2-5/8
* 3 - Blower On, Burner On, and Safety Lockout;
4th light is Dirty Filter Indicator
** On the console with Gas Control Options AG 30, 31, 32, 33, 47, 48, 51
*** On the console with Air Control Options AR19 or AR22
**** Subtract 7/8" when recessing

Form P-RDF, Page 20

/16

(33

2-3/8
(60)
)

6(

5-1

152

5/3

)

2(

139

)

1-3

/32

(28
)
4-7/16
(113)

1-3

/32

(28

)

Disconnect
Switch

CODE 170 - OUTDOOR
Disconnect Switches
30 Amp, 240 Volt, Non-Fusible
30 Amp, 240 Volt, Fusible
30 Amp, 600 Volt, Non-Fusible
30 Amp, 600 Volt, Fusible
60 Amp, 240-Volt, Non-Fusible
60 Amp, 240-Volt, Fusible
60 Amp, 600 Volt, Non-Fusible
60 Amp, 600-Volt, Fusible
100 Amp, 240-Volt, Non-Fusible
100 Amp, 240-Volt, Fusible
100 Amp, 600 Volt, Non-Fusible
100 Amp, 600-Volt, Fusible
200 Amp, 240-Volt, Non-Fusible
200 Amp, 240-Volt, Fusible
200 Amp, 600 Volt, Non-Fusible
200 Amp, 600-Volt, Fusible

USA Only
Opt
P/N
CP5
40269
CP6
87147
CP7
20367
CP8
20368
CP30 161469
CP17
89932
CP38
90973
CP20
90974
CP31 162834
CP18
90973
CP39 155013
CP36 155010
CP32 155007
CP19
91076
CP40 155014
CP37 155011

Canada Only
Opt
P/N
--CP59 208054
CP42 208046
--CP61 208056
CP44 208048
--CP63 208058
CP46 208050
--CP65 208060
CP48 208052

General Guide to Outdoor/Raintight Switches by Option Code
(unit motor/voltage availability varies by model/size)
USA Outdoor
Voltage/
Motor
Canada Outdoor
Amps
Phase
HP
Fusible Non-Fuse Fusible Non-Fuse
1/4 to 1-1/2
30
CP6
CP5
CP42
CP59
115/1
2 to 3
60
CP17
CP30
CP44
CP61
1/4 to 3
30
CP6
CP5
CP42
CP59
208/1 and
5 to 10
60
CP17
CP30
CP44
CP61
230/1
1/4 to 5
30
CP6
CP5
CP42
CP59
208/3 and
7-1/2 to 15
60
CP17
CP30
CP44
CP61
230/3
20 to 25
100 CP18
CP31
CP46
CP63
30
200 CP19
CP32
CP48
CP65
1/4 to 15
30
CP8
CP7
CP42
CP59
460/3 and
20 to 30
60
CP20
CP38
CP44
CP61
575/3

CODE 171 - INDOOR
Disconnect Switches
30 Amp, 240 Volt, Non-Fusible
30 Amp, 240 Volt, Fusible
30 Amp, 600 Volt, Non-Fusible
30 Amp, 600 Volt, Fusible
60 Amp, 240-Volt, Non-Fusible
60 Amp, 240-Volt, Fusible
60 Amp, 600 Volt, Non-Fusible
60 Amp, 600-Volt, Fusible
100 Amp, 240-Volt, Non-Fusible
100 Amp, 240-Volt, Fusible
100 Amp, 600 Volt, Non-Fusible
100 Amp, 600-Volt, Fusible
200 Amp, 240-Volt, Non-Fusible
200 Amp, 240-Volt, Fusible
200 Amp, 600 Volt, Non-Fusible
200 Amp, 600-Volt, Fusible

USA Only
Opt
P/N
CP1
40267
CP2
40268
CP3
50365
CP4
50366
CP21 161462
CP17 89932*
CP23 161464
CP20 90974*
CP22 161463
CP18 90973*
CP24 164330
CP36 155010*
CP26 155005
CP19 91076*
CP35 155009
CP37 155011*

Canada Only
Opt
P/N
--CP58 208053
CP41 208045
--CP60 208055
CP43 208047
--CP62 208057
CP45 208049
--CP64 208059
CP47 208051

General Guide to Indoor Disconnect Switches by Option Code
(unit motor/voltage availability varies by model/size)
USA Indoor
Voltage/
Motor
Canada Indoor
Amps
Phase
HP
Fusible Non-Fuse Fusible Non-Fuse
1/4 to 1-1/2 30
CP2
CP1
CP41
CP58
115/1
2 to 3
60
CP27
CP21
CP43
CP60
1/4 to 3
30
CP2
CP1
CP41
CP58
208/1 and
5 to 10
60
CP27
CP21
CP43
CP60
230/1
1/4 to 5
30
CP2
CP1
CP41
CP58
208/3 and
7-1/2 to 15
60
CP27
CP21
CP43
CP60
230/3
20 to 25
100 CP28
CP22
CP45
CP62
30
200 CP29
CP26
CP47
CP64
460/3 and
1/4 to 15
30
CP4
CP3
CP41
CP58
575/3
20 to 30
60
CP33
CP23
CP43
CP60
* Actually an outdoor switch.

Form P-RDF, Page 21

Blowers
Hardware for 3/8" Motor
Mounting Bolts

180

183

Hardware for 5/16" Motor
Mounting Bolts
Blower Motor - RDF 2 and 3

183
184
185
Blower and Motor - RDF 1
CODE Description

180

Blower with shaft
and bearings

Size
Mfg #

1-20
1357

1-40
1360

10"
A10-10AC

12"
A12-12AC

1-50
86983

1-65
86984

15"
18"
A15-15A A18-18A

Class
Shaft

Class 1
1"

—

—

—

—

Size
Mfg #

180A Blower

Class
Shaft
Class 1 Blowers

11302
3/4x22

11303
1x22

100747
1x23

100748
1x28.8

Class 2 Blowers

—

—

—

—

Class 1 Blowers

7310

10437

Class 2 Blowers

—

—

Shaft

180B Blower

Bearings

181

10437
10437
Ball Bearings (2)
—

—

2-80
92343*

2-120
89345

3-180
91067

3-260
91069

18"
20"
22"
30"
022920-03 027550-02 020350-01 029353-02
A20-20K A22-22K A30-22K
Class 1
Class 1
Class 1
Class 1
1-7/16"
1-7/16"
1-7/16"
1-11/16"

89658

—

91068

91070

18"
0217142-15
A18-18A
Class 2
1-7/16"
100748
100746
2x28.8
1.44x
37.25
100749
—
1.44x
38.5"
10437
106942
1.44"

106942
1.44"
Pillowblock
111389
111389

22"
30"
029353-01 029353-03
A22-22K A30-22K
Class 2
Class 2
2-3/16"
2-11/16"
100751
100754
1.44x
1.69x
45.73
46.25
100752
101705
2.19x
2.69x
45.75"
46.25'
106942
100755
1.44"
1.69"
Pillowblock (2)
—
100753
101710
2.19"
2.69"
(2)
Pillowblock (2)
111389
111389
111389
126588** 126588**
111390
111390
111390

External Shaft Support Bearing Plate 111389
111389
111389
- for units with dampers (Options AQ3, AQ4 and/or AR19, AR20, AR22, AR23)
182 Bearing BF-1127-502-A - for units
111390
111390
111390
111390
111390
with dampers, Options AQ3, AQ4, and/or AR19, AR20, AR22, AR23)
183 Blower Motor Mounting Plate
12578
12578
12578
12578
94371
94371
94371
94371
184 Mtr Mounting Plate Left Support
87015
87015
87015
87015
94369
94369
94369
94369
185 Mtr Mounting Plate Right Support
87016
87016
87016
87016
94369
94369
94369
94369
186 Blower Support (Horzntl Discharge) 207840
207840
207840
207840
(2)207461 (2)207461 (3)207462 (3)207462
*Effective 8/90, RDF 2-80 models are no longer manufactured with a Class 1 blower. P/N 92343 is no longer available. Replace with Class 2 blower,
P/N 89658 and Q1-1-7/16" Bushing, P/N 16177.
** Order P/N 126588 when heater has Option AR23, outside and return dampers controlled by a remote pressure sensor.
Form P-RDF, Page 22

Drives
Replacement Drive Components
are Listed in Tables on pages 2331. Tables are by RDF Size, Type of
Motor, Motor HP, and RPM (Option
AM, see chart top of page 23),
CODE 200 - Motor Sheave
CODE 201 - Blower Sheave
CODE 202 - Belt
CODE 203 - Bushing

NOTE: Read each drive table
carefully. They are not all in the
same format.

Belt Tension - Check belt tension. Proper belt tension is important to the long life of the belt
and motor. A loose belt will cause wear and slippage. Too much tension will cause excessive
motor and blower bearing wear. If adjustment is required, adjust belt tension by means of the
adjusting screw on the motor base until the belt can be depressed 1/2" to 3/4". Tighten the
lock nut on the adjusting screw. Be sure the belt is aligned in the pulleys.
Blower Speed Adjustment - Units are set at the factory for the RPM required to meet the CFM
and external static pressure specified on the order. If the estimated external static is incorrect,
or changes are made to the duct system, the blower RPM may have to be changed. Motors
are equipped with adjustable pitch pulleys which permit adjustment of blower speed.
To make adjustments on all RDF-1 units and on RDF-2 and RDF-3 units with less than 7-1/
2 HP motor (units with a Browning motor sheave Model VP), follow these instructions:
1) Loosen belt tension and remove belt.
2) Loosen the set screw on the side of the pulley away from the motor.
3) Turn adjustable half of the pulley inward to increase blower speed or outward
to decrease speed. One turn of the pulley will change speed 8 to 10%.
4) After setting the pulley, tighten the set screw on the flat portion of the pulley
shaft.
5) Replace belts and adjust belt tension.
6) Always check motor amps with an amp meter after RPM adjustment. The
maximum motor amp rating on the nameplate must not be exceeded.
In RDF-2 and RDF-3 models with 7-1/2 HP and larger motors (units with adjustable Browning motor sheave Model MV), follow these instructions for adjusting RPM:
1) Slack off all belt tension by moving the motor toward driven shaft until the
belts are free of grooves. For easiest adjustment, remove the belts from the
grooves.
2) On the outer locking ring, locate the two locking screws that are directly
across from each other. Loosen, but do not remove, those two screws. Do not
loosen any other screws.
3) Adjust sheave to desired pitch diameter by turning the outer locking ring.
One complete turn of the outer locking ring will result in .233" change in
pitch diameter. To increase blower speed, decrease diameter. CAUTION: Do
not adjust sheaves in either direction to the point where moveable and
stationary flanges are in contact.
4) After completing adjustment, tighten both locking screws in the outer
locking ring.
5) Replace belts and move motor away from the drive shaft to apply sufficient
belt tension to prevent slippage. Be sure that the belts are aligned in the
pulley grooves properly and are not angled from pulley to pulley.
6) Always check motor amps with an amp meter after RPM adjustment. The
maximum motor amp rating on the nameplate must not be exceeded.

Blower Pulley - Size 2-80, 2-120, 119 and 120 systems equipped with 3 and 5 HP motors with
a 15.4" diameter and larger blower pulley or a 7-1/2 HP and larger motor and all Size 3-180, 3260, 122, and 130 systems are equipped with a split taper bushing in the blower pulley. The
split taper bushings must be loosened in order to remove the pulley. Follow these instructions to loosen the bushing.
1) Notice that there are three cap screws in the
bushing and two holes without screws, called
push-off holes (see illustration).
2) Remove the three cap screws.
3) Put two of the cap screws into the two push-off
holes. Tighten these two screws evenly until
the pulley is loosened.
4) Pulley may now be removed from the shaft.

2 Push-Off
Holes
Split Taper
Bushing

3 Cap Screws

Form P-RDF, Page 23

Drive Components (cont'd)
Notes and Key to Option Codes on Drive Tables, pages 24 - 32
Option ............... RPM
AMA3 ............... 301-350
AMA4 ............... 351-400
AM1 .................. 401-450
AM2 .................. 451-500
AM3 .................. 501-550
AM4 .................. 551-600
AM5 .................. 601-650

Option ............... RPM
AM6 .................. 651-700
AM7 .................. 701-750
AM8 .................. 751-800
AM9 .................. 801-850
AM10 ................ 851-900
AM11 ................ 901-950
AM12 ................ 951-1000

Option ............... RPM
AM13 ................ 1001-1050
AM14 ................ 1051-1100
AM15 ................ 1101-1150
AM16 ................ 1151-1200
AM17 ................ 1201-1250
AM18 ................ 1251-1300
AM19 ................ 1301-1350

Option ............... RPM
AM20 ................ 1351-1400
AM21 ................ 1401-1450
AM22 ................ 1451-1500
AM23 ................ 1501-1550
AM24 ................ 1551-1600
AM25 ................ 1601-1650
AM26 ................ 1651-1700

NOTE : Where 575V (AK8) is listed, the two corresponding AL option lines above apply to all other voltages with that HP.

Model RDF 1-20
Open Motor
HP

Option
AL4
AL4
1/2
AL4
AL4
AL5
AL5
AL5
3/4
AL5
AL5
AL5
AL6
AL6
AL6-AK8
AL6-AK8
1
AL6
AL6
AL6-AK8
AL6-AK8
AL7
AL7
AL7-AK8
AL7-AK8
AL7
AL7
1-1/2
AL7-AK8
AL7-AK8
AL7
AL7
AL7-AK8
AL7-AK8

2

Horz/Vert
Discharge
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H

AL8
AL8
AL8
AL8

V
H
V
H

AL8
AL8
AL8
AL8

V
H
V
H

Form P-RDF, Page 24

CODE 200 - Motor
CODE 201- Blower
CODE
Drive Option
CODE 202 - Belt
Sheave
Sheave
203 (See table
P/N
Mfr
No.
Bore
P/N
Mfr
No.
Bore
P/N
Mfr
No.
Bushing
above.)
AM6-9
A52
7962
111607
50513
AK74
AM6-9
A43
7962
111607
50470
1VL40 5/8
3/4
AM10-15
A49
7962
105480
50475
AK54
AM10-15
7962
105480
105493 A39
AM8-11
A52
105476
111682
50513
AK71
1VL44
AM8-11
A43
105476
111682
50470
AM12-16
1VL40
A48
7962
105479 AK49
65403
5/8
3/4
AM12-16 105476 1VL44
A41
111684 AK59
50500
AM17-21
A50
13013
105480
88558
AK54
1VM50
AM17-21
A41
13013
105480
50500
AM10-15
A49
7962
105480
50475
5/8
AM10-15
7962
105480
105493 A39
AK54
1VL40
AM10-15 106748
A49
105480
50475
7/8
AM10-15 106748
105480
105493 A39
3/4
AM16-20
A51
13013
111684
65404
5/8
AM16-20
13013
111684
105493 A39
AK59
1VM50
AM16-20
37451
111684
105493 A39
7/8
AM16-20
A51
37451
111684
65404
AM10-15
A49
7962
105480
50475
5/8
AM10-15
7962
105480
105493 A39
1VL40
AK54
AM10-15 106748
A49
105480
50475
7/8
AM10-15 106748
105480
105493 A39
AM16-20
A51
13013
111684
65404
5/8
AM16-20
13013
111684
105493 A39
AK59 3/4
1VM50
AM16-20
37451
111684
105493 A39
7/8
AM16-20
A51
37451
111684
65404
AM21-24
1VL40
A47
7962
105478 AK41
50474
5/8
AM21-24
105487
16151 1VP56
110807 AK56H
101412 A42
AM21-24 106748
A47
105478
50474
AK41
1VL40 7/8
AM21-24 106748
105478
101412 A42
2 HP Drive Components for Model RDF 1-20 Series 3 only
AM15-20
37451
111684
65404
A51
1VM50
AK59
AM15-20
37451
111684
105493 A39
7/8
3/4
AM21-24 106748
105478
50474
A47
1VL40
AK41
AM21-24 106748
105478
101412 A42
2 HP Drive Components for Model RDF 1-20 prior to Series 3
AM15-20
A51
13013
111684
65404
1VM50
AK59
AM15-20
13013
111684
105493 A39
5/8
3/4
AM21-24
1VL40
A47
7962
105478
50474
AK41
AM21-24
16151 1VP56
105478
101412 A42

Drive Components (cont'd)
NOTE : Where 575V (AK8) is listed, the two corresponding AL option lines above apply to all other voltages with that HP.

Model RDF 1-40
Open Motor
HP

Option
AL5
AL5
AL5
3/4
AL5
AL5
AL5
AL6
AL6
AL6-AK8
AL6-AK8
1
AL6
AL6
AL6-AK8
AL6-AK8
AL7
AL7
AL7-AK8
AL7-AK8
AL7
AL7
1-1/2
AL7-AK8
AL7-AK8
AL7
AL7
AL7-AK8
AL7-AK8

2

3

5

CODE 200 - Motor
CODE 201 - Blower
Sheave
Sheave
P/N Mfr No. Bore
P/N Mfr No. Bore
AM4-6
7962
19111
AK84
AM4-6
7962
19111
1VL40
5/8
AM7-11
7962
18797
1
AK64
AM7-11
7962
18797
AM12-17 105476
105482
AK56
1VL44
7/8
AM12-17 105476
105482
AM7-11
7962
18797
5/8
AM7-11
7962
18797
AK64
1VL40
AM7-11
106748
18797
7/8
AM7-11
106748
18797
1
AM12-17 105476
105482
5/8
AM12-17 105476
105482
1VL44
AK56
AM12-17 106758
105482
7/8
AM12-17 106758
105482
AM7-11
7962
18797
5/8
AM7-11
7962
18797
AK64
1VL40
AM7-11
106748
18797
7/8
AM7-11
106748
18797
AM12-17 105476
105482
5/8
AM12-17 105476
105482
1
1VL44
AM12-17 106758
105482
7/8
AM12-17 106758
105482
AK56
AM18-21
13013
105482
5/8
AM18-21
13013
105482
1VM50
AM18-21
37451
105482
7/8
AM18-21
37451
105482
2 HP Drive Components for Model RDF 1-40 Series 3 only
AM7-11
106748
18797
AK64
AM7-11
106748
18797
1VL40
AM12-17 106758
105482
7/8
1
AM12-17 106758
105482
AK56
AM18-21
37451
105482
1VM50
AM18-21
37451
105482
2 HP Drive Components for Model RDF 1-40 prior to Series 3
AM7-11
7962
18797
AK64
1VL40
AM7-11
7962
18797
AM12-17 105476
105482
5/8
1
1VL44
AM12-17 105476
105482
AK56
AM18-21
13013
105482
1VM50
AM18-21
13013
105482
AM12-17 106748
111609
AK99
AM12-17 106748
111609
1
1VL40
7/8
AM18-21 106748
19111
AK84
AM18-21 106748
19111
AM14-18
8973
30621
2AK124
AM14-18
8973
30621
1
2VP50
7/8
AM19-23
8973
7955
2AK104
AM19-23
8973
7955

Horz/Vert Drive Option
Discharge (See page 23.)
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H

AL8
AL8
AL8
AL8
AL8
AL8

V
H
V
H
V
H

AL8
AL8
AL8
AL8
AL8
AL8
AL9
AL9
AL9
AL9
AL10
AL10
AL10
AL10

V
H
V
H
V
H
V
H
V
H
V
H
V
H

CODE 202 - Belt
P/N Mfr No.
A53
50513
A46
50473
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
101412 A42
A49
50475
A43
50470
A49
50475
A43
50470
50475
101412
50475
101412
50475
50470

A49
A42
A49
A42
A49
A43

50475
101412
50475
101412
50475
50470
16132
65403
50513
50473
50477
16131
16134
88558

A49
A42
A49
A42
A49
A43
A55
A48
A52
A46
A60
A54
A57
A50

Form P-RDF, Page 25

Drive Components (cont'd)
NOTE : Where 575V (AK8) is listed, the two corresponding AL option lines above apply to all other voltages with that HP.

Model RDF 1-50
Open Motor
HP

Option
AL6
AL6
AL6-AK8
AL6-AK8
1
AL6
AL6
AL6-AK8
AL6-AK8
AL7
AL7
AL7-AK8
AL7-AK8
1-1/2
AL7
AL7
AL7-AK8
AL7-AK8

2

3

5

CODE 200 - Motor
CODE 201- Blower
Sheave
Sheave
P/N Mfr No. Bore P/N
Mfr No. Bore
AM4-6
7962
19111
5/8
AM4-6
7962
19111
AK84
1VL40
AM4-6
106748
19111
7/8
AM4-6
106748
19111
1
AM7-11
7962
18797
5/8
AM7-11
7962
18797
AK64
1VL40
AM7-11
106748
18797
7/8
AM7-11
106748
18797
AM4-6
7962
19111
5/8
AM4-6
7962
19111
1VL40
AK84
AM4-6
106748
19111
7/8
AM4-6
106748
19111
1
AM7-11
7962
18797
5/8
AM7-11
7962
18797
1VL40
AK64
AM7-11
106748
18797
7/8
AM7-11
106748
18797
2 HP Drive Components for Model RDF 1-50 Series 3 only
AM4-6
106748
19111
AK84
AM4-6
106748
19111
1VL40 7/8
1
AM7-11
106748
18797
AK64
AM7-11
106748
18797
2 HP Drive Components for Model RDF 1-50 prior to Series 3
AM4-6
7962
19111
AK84
AM4-6
7962
19111
1VL40 5/8
1
AM7-11
7962
18797
AK64
AM7-11
7962
18797
AM8-11
106758
113372
1VL44
AK144
AM8-11
106758
113372
7/8
1
AM12-16
37451
50520
1VM50
AK134
AM12-16
37451
50520
AM8-13
87500
7955
2VP36
2AK104
AM8-13
87500
7955
7/8
1
AM14-18
8973
30621
2VP50
2AK124
AM14-18
8973
30621

Horz/Vert Drive Option
Discharge (See page 23.)
V
H
V
H
V
H
V
H
V
H
V
H
V
H
V
H

AL8
AL8
AL8
AL8

V
H
V
H

AL8
AL8
AL8
AL8
AL9
AL9
AL9
AL9
AL10
AL10
AL10
AL10

V
H
V
H
V
H
V
H
V
H
V
H

Form P-RDF, Page 26

CODE 202 - Belt
P/N Mfr No.
A50
88558
A46
50473
A50
88558
A46
50473
A47
50474
101412 A42
A47
50474
101412 A42
A50
88558
A46
50473
A50
88558
A46
50473
A47
50474
101412 A42
A47
50474
101412 A42
88558
50473
50474
101412

A50
A46
A47
A42

88558
50473
50474
101412
88560
50476
50477
16133
16130
50475
50476
16131

A50
A46
A47
A42
A61
A58
A60
A56
A53
A49
A58
A54

Drive Components (cont'd)
NOTE : Where 575V (AK8) is listed, the two corresponding AL option lines above apply to all other voltages with that HP.

Model RDF 1-65
Open Motor
HP

Option
AL7
AL7
AL7-AK8
AL7-AK8
AL7
AL7
1-1/2
AL7-AK8
AL7-AK8
AL7
AL7
AL7-AK8
AL7-AK8

2

3

5

CODE 200 - Motor
CODE 201- Blower
Sheave
Sheave
P/N Mfr No. Bore P/N
Mfr No. Bore
AM2-3
13013
113372
5/8
AM2-3
13013
113372
1VM50
AK144
AM4-6
37451
113372
7/8
AM4-6
37451
113372
AM4-6
7962
19111
5/8
AM4-6
7962
19111
1
AK84
1VL40
AM4-6
106748
19111
7/8
AM4-6
106748
19111
AM7-11
7962
18797
5/8
AM7-11
7962
18797
AK64
1VL40
AM7-11
106748
18797
7/8
AM7-11
106748
18797
2 HP Drive Components for Model RDF 1-65 Series 3 only
AM2-3
37451
113372
AK144
1VM50
AM2-3
37451
113372
AM4-6
106748
19111
1
7/8
AK84
AM4-6
106748
19111
1VL40
AM7-11
106748
18797
AK64
AM7-11
106748
18797
2 HP Drive Components for Model RDF 1-65 prior to Series 3
AM2-3
13013
113372
AK144
1VM50
AM2-3
13013
113372
AM4-6
7962
19111
5/8
1
AK84
AM4-6
7962
19111
1VL40
AM7-11
7962
18797
AK64
AM7-11
7962
18797
AM4-7
87500
113382
2VP36
AK144
AM4-7
87500
113382
1
7/8
AM8-11
6599
30622
2VP42
2AK134H
AM8-11
6599
30622
AM7-13
87500
7955
2VP36 7/8
2AK104
1
AM7-13
87500
7955

Horz/Vert Drive Option
Discharge (See page 23.)
V
H
V
H
V
H
V
H
V
H
V
H

AL8
AL8
AL8
AL8
AL8
AL8

V
H
V
H
V
H

AL8
AL8
AL8
AL8
AL8
AL8
AL9
AL9
AL9
AL9
AL10
AL10

V
H
V
H
V
H
V
H
V
H
V
H

CODE
203 Mfr No. Bushing
A61
A59
A61
A59
A49
A46
A49
A46
A45
A43
A45
A43
-

CODE 202 - Belt
P/N
88560
92402
88560
92403
50475
50473
50475
50473
50472
50470
50472
50470
88560
92403
50475
50473
50472
50470

A61
A59
A49
A46
A45
A43

-

88560
92403
50475
50473
50472
50470
92402
50476
50476
16133
65404
88558

A61
A59
A49
A46
A45
A43
A59
A58
A58
A56
A51
A50

92203
92203
-

Form P-RDF, Page 27

Drive Components (cont'd)
(Effective 8/90 all RDF-2-80 Models are equipped with a Class 2 blower. For RDF-2-80 with a Class 1 blower, see page 28. A Class 2 blower was
available as a option prior to 8/90.)

Model RDF 2-80 with a CLASS 2 BLOWER
CODE 200 - Motor Sheave CODE 201 - Blower Sheave
CODE 202 - Belt
CODE 203 P/N
Mfr No.
Bore P/N
Mfr No.
Bore
P/N Qty Mfr No. Bushing
2 HP Drive Components for Model RDF 2-80 Series 3 only
AL8
V
AM3-5
B55
106748
114026
112531 1
89659
1VL40
7/8
BK110H 1-7/16
AL8
H
AM3-5
B53
106748
114026
92222 1
89659
2
2 HP Drive Components for Model RDF 2-80 prior to Series 3
AL8
V
AM3-5
B55
7962
114026
112531 1
89659
1VL40
5/8
BK110H 1-7/16
AL8
H
AM3-5
B53
7962
114026
92222 1
89659
AL9
V
AM3-4
A69
87500
114027
16558 2
89659
2VP36
2AK184H
AL9
H
AM3-4
A67
87500
114027
16139 2
89659
AL9
V
AM5-9
A59
110125
114028
92402 1
89659
7/8
3
1VP34
AK134H 1-7/16
AL9
H
AM5-9
A57
110125
114028
16134 1
89659
AL9
V
AM10-13 106748
A59
114030
92402 1
89659
1VL40
AK124H
AL9
H
AM10-13 106748
A55
114030
16132 1
89659
AL10
V
AM3-4
A69
87500
114027
16558 2
89659
2AK184H
2VP36
AL10
H
AM3-4
A67
87500
114027
16139 2
89659
AL10
V
AM5-6
BX65
87500
114032 2B5V160
92276 2
114033
7/8
1-7/16
5
AL10
H
AM5-6
2VP42
A67
6599
114027 2AK184H
16139 2
89659
AL10
V
AM7-11
A58
87500
114034
50476 2
89659
2VP36
2AK124H
H
AM7-11
A55
AL10
87500
114034
16132 2
89659
AL11
V
AM6-7
2VP68
B66
113802
89651
114104 2
89659
2BK16 0H
AL11
H
AM6-7
2VP71
B64
114249
89651
92414 2
89659
AL11
V
AM8-9
B58
106257
113811
92226 2
89659
2VP60
2BK120H
AL11
H
AM8-9
B56
106257
113811
92224 2
89659
1-3/8
1-7/16
7-1/2
AL11
V
AM10-11
BX59
16150
114045
92280 2
114033
2VP62
2BV110
AL11
H
AM10-11
BX55
16150
114045
92409 2
114033
AL11
V
AM12-15 106257
B53
113804
92222 2
89659
2VP60
2BK90H
AL11
H
AM12-15 106257
B51
113804
92220 2
89659
AL12
V
AM6-7
2VP68
B66
113802
89651
114104 2
89659
2BK16 0H
AL12
H
AM6-7
2VP71
B64
114249
89651
92414 2
89659
AL12
V
AM8-9
B58
106257
113811
92226 2
89659
2BK120H
2VP60
AL12
H
AM8-9
B56
106257
113811
92224 2
89659
1-7/16
1-3/8
10
AL12
V
AM10-11
BX59
16150
114045
92280 2
114033
2BV110
2VP62
AL12
H
AM10-11
BX55
16150
114045
92409 2
114033
AL12
V
AM12-15 106257
B53
113804
92222 2
89659
2BK90H
2VP60
AL12
H
AM12-15 106257
B51
113804
92220 2
89659
AL15
V
AM7-9
BX55
91615 2MVP40B54
113811 2BK120H
92409 2
89659
AL15
H
AM7-9
B59
113809
92204 2BK140H
16143 2
89659
2VP71A
AL15
V
AM10-11 113809
B58
89650
92226 2
89659
2BK130H
AL15
H
AM10-11 113809
B57
89650
92225 2
89659
1-5/8
1-7/16
15
AL15
V
AM12-16 114047
BX50
114033
114048
92236 2
2MVP45B59
AL15
H
AM12-16 114047
B49
114048
113805 2
114033
2B5V86
AL15
V
AM17-20 113808
BX53
114048
114341 2
114033
2VP75
AL15
H
AM17-20 113808
BX51
114048
92237 2
114033
CODE 202 - Belt
CODE 203 TEFC Motor Horz/Vert Drive Option CODE 200 - Motor Sheave CODE 201 - Blower Sheave
HP Option Discharge (See page 23.) P/N
Mfr No.
Bore P/N
Mfr No.
Bore
P/N Qty Mfr No. Bushing
AL27
H
AM7-9
1VP50
1-1/8 113799 AK184H 1-7/16 16139 2
A67
5
111681
89659
NOTE: If drive components are required for units with a TEFC or Premium Efficiency motor not listed here, contact your Distributor or the
Factory Service Department. Be prepared to provide complete Model and Serial No.
Open Motor Horz/Vert Drive Option
HP Option Discharge (See page 23.)

Form P-RDF, Page 28

Drive Components (cont'd)
Model RDF-2-80 with a Class 1 Blower
(Effective 8/90 all RDF-2-80 Models are equipped with a Class 2 blower. For RDF-2-890 with a Class 2 blower, see page 27. A Class 2 blower was
available as a option prior to 8/90.

Form P-RDF, Page 29

Drive Components (cont'd)

Model RDF 2-120
* Open Motor Horz/Vert Drive Option CODE 200 - Motor Sheave CODE 201 - Blower Sheave
CODE 202 - Belt
CODE 203
HP
Option Discharge (See page 23.) P/N
Mfr No.
Bore P/N
Mfr No.
Bore
P/N Qty Mfr No. - Bushing
2 HP Drive Components for Model RDF 2-120 Series 3 only
AL8
V
AM3-5
1VL44
A53
106758
113798 AK104H
16130 1
89659
7/8
1-7/16
AL8
H
AM3-5
1VL40
B54
106748
114026 BK110H
92223 1
89659
2
2 HP Drive Components for Model RDF 2-120 prior to Series 3
AL8
V
AM3-5
1VL44
A53
105476
113798 AK104H
16130 1
89659
1-7/16
5/8
AL8
H
AM3-5
1VL40
B54
7962
114026 BK110H
92223 1
89659
AL9
V
AM3-4
2BK10H
BX68
87500
89652
92241 2
89659
2VP36
AL9
H
AM3-4
A69
87500
114027 2AK184H
16558 2
89659
AL9
V
AM5-7
1VL44
A69
106758
113799 AK184H
16558 1
89659
7/8
1-7/16
3
AL9
H
AM5-7
1VP34
A59
110125
114028 AK134H
92402 1
89659
AL9
V
AM8-11
A61
106758
113800 AK144H
88560 1
89659
1VL44
AL9
H
AM8-11
A63
106758
113800 AK144H
16138 1
89659
AL10
V
AM3-4
2BK10H
BX68
87500
89652
92241 2
89659
2VP36
AL10
H
AM3-4
A69
87500
114027 2AK184H
16558 2
89659
AL10
V
AM5-7
BK160H
BX62
87500
89651
92411 2
89659
7/8
1-7/16
5
AL10
H
AM5-7
2VP42
A70
6599
114027 2AK184H
114257 2
89659
AL10
V
AM8-11
A53
87500
113801 2AK104H
16130 2
89659
2VP36
AL10
H
AM8-11
A57
87500
114034 2AK124H
16134 2
89659
AL11
V
AM4-5
BX64
110771
114032 2B5V160
114258 2
114033
2VP65
AL11
H
AM4-5
BX67
110771
114032 2B5V160
80841 2
114033
AL11
V
AM6-7
2VP68
BX63
113802
89651 2BK160H
92278 2
89659
AL11
H
AM6-7
2VP71
B66
114249
89651 2BK160H
114104 2
89659
1-3/8
1-7/16
7-1/2
AL11
V
AM8-11
B54
106257
113803 2BK110H
92223 2
89659
AL11
H
AM8-11
B56
106257
113803 2BK110H
92224 2
89659
2VP60
AL11
V
AM12-15 106257
B50
113804 2BK90H
114010 2
89659
AL11
H
AM12-15 106257
B53
113804 2BK90H
92222 2
89659
AL12
V
AM4-5
BX64
110771
114032 2B5V160
114258 2
114033
2VP65
AL12
H
AM4-5
BX67
110771
114032 2B5V160
80841 2
114033
AL12
V
AM6-7
2VP68
BX63
113802
89651 2BK160H
92278 2
89659
AL12
H
AM6-7
2VP71
B66
114249
89651 2BK160H
114104 2
89659
1-3/8
1-7/16
10
AL12
V
AM8-11
B54
106257
113803 2BK110H
92223 2
89659
AL12
H
AM8-11
B56
106257
113803 2BK110H
92224 2
89659
2VP60
AL12
V
AM12-15 106257
B50
113804 2BK90H
114010 2
89659
AL12
H
AM12-15 106257
B53
113804 2BK90H
92222 2
89659
AL15
V
AM6-7
2VP75
BX62
113808
114032 2B5V160
92411 2
114033
AL15
H
AM6-7
BX55
91615 2MVP40B54
113811 2BK120H
92409 2
89659
AL15
V
AM8-9
2VP71A
B58
113809
92204 2BK140H
92226 2
89659
AL15
H
AM8-9
BX55
91615 2MVP40B54
113811 2BK120H
92409 2
89659
1-5/8
1-7/16
15
AL15
V
AM10-11 113808
2VP75
B56
89650
92224 2
89659
2BK130H
AL15
H
AM10-11 113809
2VP71A
B59
89650
16143 2
89659
AL15
V
AM12-13 113808
B55
113811
112531 2
89659
2VP75
2BK120H
AL15
H
AM12-13 113808
B58
113811
92226 2
89659

* If drive components are required for units with a 3-10HP TEFC or 3-10 HP Premium Efficiency motor, contact your Distributor or the Factory
Service Department. Be prepared to provide complete Model and Serial No.

Form P-RDF, Page 30

Drive Components (cont'd)
Model RDF 3-180
*Open Motor Blower Horz/Vert Drive Option
HP
Option Class Discharge (See page 23.)
AL10
1
V
AM2-3
AL10
1
V
AM4-5
5
AL10
1
H
AM2-3
AL10
1
H
AM4-5
AL11/12
1
V
AM1
AL11/12
1
V
AM2
AL11/12
1
V
AM3
AL11/12
1
V
AM4-5
1
V
AM6-7
7-1/2 AL11/12
AL11/12
1
V
AM8-9
and
AL11/12
1
H
AM1
10
AL11/12
1
H
AM2
AL11/12
1
H
AM3
AL11/12
1
H
AM4-5
AL11/12
1
H
AM6-7
AL11/12
1
H
AM8-9
AL15/16
1
V
AM4-5
AL15/16
1
V
AM6-7
AL15/16
1
V
AM8-10
AL15/16
1
V
AM11-14
AL15/16
2
V
AM2-3
AL15/16
2
V
AM4-6
AL15/16
2
V
AM7-9
2
V
AM10-12
15 AL15/16
AL15/16
2
V
AM13-15
and
AL15/16
1
H
AM4-5
20
AL15/16
1
H
AM6-7
AL15/16
1
H
AM8-10
AL15/16
1
H
AM11-14
AL15/16
2
H
AM2-3
AL15/16
2
H
AM4-6
AL15/16
2
H
AM7-9
AL15/16
2
H
AM10-12
AL15/16
2
H
AM13-15
AL17/18
2
V
AM5-6
AL17/18
2
V
AM7-9
AL17/18
2
V
AM10-12
25
AL17/18
2
V
AM13-16
and
AL17/18
2
H
AM5-6
30
AL17/18
2
H
AM7-9
AL17/18
2
H
AM10-12
AL17/18
2
H
AM13-16

CODE 200 - Motor Sheave
P/N
Mfr No.
Bore
2VP42
6599
87500
2VP36
7/8
2VP42
6599
87500
2VP36
2VP71
114249
2VP60
106257
2VP62
16150
2VP65
110771
2VP71
114249
106257
2VP60
1-3/8
2VP71
114249
2VP60
106257
2VP62
16150
2VP65
110771
2VP71
114249
106257
2VP60
89644 3MVP40B54
115719 3MVP50B64
89645 3MVP45B59
89644 3MVP40B54
89645 3MVP45B59
89644
3MVP40B54
89644
115719 3MVP50B64
89645 3MVP45B59
1-5/8
89644 3MVP40B54
115719 3MVP50B64
89645 3MVP45B59
89644 3MVP40B54
89645 3MVP45B59
89644
3MVP40B54
89644
115719 3MVP50B64
89645 3MVP45B59
115931 4MVP50B64
115946 4MVP45B59
115931 4MVP50B64
115931 4MVP50B64
1-7/8
115931 4MVP50B64
115946 4MVP45B59
115931 4MVP50B64
115931 4MVP50B64

CODE 201- Blower Sheave
P/N
Mfr No.
Bore
115718 2B5V250
89652
2BK190H
1-7/16
115718 2B5V250
89652
2BK190H
115718 2B5V250
89652
2BK190H
89652
114032
2B5V160
114032
113811 2BK120H
1-7/16
115718 2B5V250
89652
2BK190H
89652
114032
2B5V160
89651
113811 2BK120H
115720 3B5V136
115721 3B5V154
1-7/16
115722 3BK120H
3BK90H
115723
115943 3B5V184
115720 3B5V136
2-3/16
115935
3B5V110
115935
3B6V90
115945
115720 3B5V136
115721 3B5V154
1-7/16
115722 3BK120H
3BK90H
115723
115943 3B5V184
115720 3B5V136
2-3/16
115935
3B5V110
115935
3B6V90
115945
116204 4MVB154R
116203 4MVB124R
116202 4MVB110R
116201 4MVB94Q
2-3/16
116204 4MVB154R
116203 4MVB124R
116202 4MVB110R
116201 4MVB94Q

CODE 202 - Belt
CODE 203
P/N Qty Mfr No. - Bushing
BX97
92319 2
114033
B86
92312 2
89659
B92
92308 2
114033
BX77
92341 2
89659
BX99
115932 2
114033
B88
115933 2
89659
B89
115934 2
89659
B84
92273 2
114033
BX85
92317 2
114033
BX75
92277 2
89659
BX93
92313 2
114033
BX79
92332 2
89659
BX79
92332 2
89659
BX75
92277 2
114033
BX75
92277 2
89659
BX66
92240 2
89659
BX77
92341 3
114033
BX81
92274 3
114033
B74
92231 3
89659
BX68
92241 3
89659
B87
92310 3
116205
BX77
92341 3
116205
B73
92230 3
116205
BX75
92277 3
116205
BX71
92243 3
116205
BX68
92241 3
114033
B73
92230 3
114033
3
B65
6010
89659
B59
16143 3
89659
B78
92234 3
116205
BX68
92241 3
116205
BX64
114258 3
116205
BX65
92276 3
116205
BX62
92411 3
116205
BX80
92412 4
116206
BX72
92277 4
116206
B73
92230 4
116206
BX70
92242 4
116207
BX71
92243 4
116206
BX65
92276 4
116206
BX63
92278 4
116206
BX61
92289 4
116207

* If drive components are required for units with a 5-15HP TEFC or 5-15 HP Premium Efficiency motor, contact your Distributor or the
Factory Service Department. Be prepared to provide complete Model and Serial No.

Form P-RDF, Page 31

Drive Components (cont'd)
Model RDF 3-260
*Open Motor Blower Horz/Vert Drive Option
HP
Option Class Discharge (See page 23.)
AL11/12
1
H
AMA3
AL11/12
1
V
AMA3
AL11/12
1
H
AMA4
7-1/2 AL11/12
1
V
AMA4
and 10 AL11/12
1
H
AM1-2
AL11/12
1
V
AM1-2
AL11/12
1
H
AM3-4
AL11/12
1
V
AM3-4
AL15/16
1
H
AMA4
AL15/16
1
V
AMA4
AL15/16
1
H
AM1
AL15/16
1
V
AM1
AL15/16
1
H
AM2
AL15/16
1
V
AM2
AL15/16
1
H
AM3-5
1
V
AM3-5
15 and AL15/16
20 AL15/16
2
H
AMA4
AL15/16
2
V
AMA4
AL15/16
2
H
AM1
AL15/16
2
V
AM1
AL15/16
2
H
AM2-3
AL15/16
2
V
AM2-3
AL15/16
2
H
AM4-6
AL15/16
2
V
AM4-6
AL17/18
2
H
AM1
AL17/18
2
V
AM1
AL17/18
2
H
AM2-3
25 and AL17/18
2
V
AM2-3
30 AL17/18
2
H
AM4-5
AL17/18
2
V
AM4-5
AL17/18
2
H
AM6-8
AL17/18
2
V
AM6-8

CODE 200 - Motor Sheave
P/N
Mfr No.
Bore
115940
2MVP35B49
115940
106257
2VP60
106257
1-3/8
89641
2MVP40B54
89641
106257
2VP60
106257
89644
3MVP40B54
89644
115719
3MVP50B54
115719
1-5/8
89644
89644
3MVP40B54
89644
89644
89645
3MVP45B59
89645
89644
3MVP40B54
89644
1-5/8
89645
3MVP45B59
89645
89644
3MVP40B54
89644
116460
4MVP55B69
116460
115946
115946
4MVP45B59 1-7/8
115946
115946
116460
4MVP55B69
116460

CODE 201- Blower Sheave
P/N
Mfr No.
Bore
115941
115941
2B5V234
115941
115941
1-11/16
115942
2B5V184
115942
114032
2B5V160
114032
115944
115944
3B5V234
115944
115944
1-11/16
115943
3B5V184
115943
115721
3B5V154
115721
116446
3MVB250R
116446
116447
3MVB200R
116447
2-11/16
116448
3MVB184Q
116448
116449
3MVB136Q
116449
116461
4MVB250R
116461
116462
4MVB184R
116462
2-11/16
116204
116204
4MVB154R
116204
116204

CODE 202 - Belt
P/N
Qty Mfr No.
2
BX103
92316
2
BX113
115947
2
BX103
92316
2
BX115
115948
2
BX93
92313
2
BX105
92314
2
BX90
92315
2
BX103
92316
3
BX100
92318
3
BX113
115947
3
B101
115865
3
BX113
115947
3
BX90
92315
3
BX103
92316
3
B84
92273
3
BX97
92319
3
BX103
92316
3
BX115
115948
3
BX93
92313
3
BX105
92314
3
BX90
92315
3
BX103
92316
3
BX81
92274
3
B94
119610
4
BX103
92316
4
BX115
115948
4
BX90
92315
4
BX103
92316
4
BX83
92333
4
BX96
92334
4
BX85
92317
4
BX97
92319

CODE 203 Bushing
115949
115949
115949
115949
115949
115949
115949
115949
115949
115949
115949
115949
115949
115949
115949
115949
116451
116451
116451
116451
91609
91609
91609
91609
116451
116451
116451
116451
116451
116451
116451
116451

* If drive components are required for units with a 7-1/2 - 20 HP TEFC or 7-1/2 - 20 HP Premium Efficiency motor, contact your Distributor or
the Factory Service Department. Be prepared to provide complete Model and Serial No.

Form P-RDF, Page 32

Cabinet Parts for Models RDF-1 Series 3

Optional Return Air
Opening

222

226
234
226

Bottom
Discharge

Outside Air
Opening

223

232

220

221

Rear View
Top View

231

Control
Compartment

228
229
Blower
Compartment

227

230

Supply Wiring
24V Wiring
Gas Supply

Control Side

Horizontal
Discharge

225
235

CODE Description
220
221
222
223
224A
224B
225
226
227
228
228A
229
230
231
232
233
234
235
236
237

224

Top Front
Top Rear
Top Clamp
Inlet Screen (Standard unit without optional inlet air hood or filter cabinet)
Front Panel Assembly including Duct Assembly for Horizontal discharge
Front Panel Assembly for unit with bottom discharge (includes insulation)
Motor Access Panel Assembly - Horizontal Discharge Only
Side Panel Assembly (includes insulation)
Front Panel Assembly for unit with bottom discharge (includes insulation)
Burner/Control Door Assembly
Positioning Hinge (Part of CODE 228)
Blower Section Door Assembly
Center Post Outer Cover
Front Corner Post Outer Cover
Left Rear Corner Post Outer Cover
Right Rear Corner Post Outer Cover
Intermediate Post Cover
Vertical Discharge Cover (hoizontal discharge only)
Pilot Access Cover Assembly
Door Latch

Front View
Model RDF Series 3
1-20 1-40 1-50 1-65
86879
86880
86882
96817
N/A N/A
87685
86848
94360
86848
86848
204476
158800
90321
86868
(2) 86865
203816
203817
203815
203994
204474
124067

Form P-RDF, Page 33

Cabinet Parts for Models RDF-2 and RDF-3 Series 3
244

Optional Return Air
Opening (F x G)

253

253

245

245

243
Bottom
Discharge

242

241

Outside Air
Opening

255

254

240
Rear View
Top View

Control
Compartment
247

246

251

252
24V Wiring
Supply Wiring
Gas Supply

Control Side

Blower
Compartment
245

256

Top Front
Top Center
Top Rear
Top Clamp
Right Rear Side Door Assembly
Side Door Assembly
Front Burner/Control Door Assembly
Rear Burner/Control Door Assembly
Positioning Hinge (Part of CODE 247)
Front Panel Assembly including Duct Assembly for Horizontal Discharge
Front Panel Assembly - Bottom Discharge
Left Front Corner Post Outer Cover
Right Front Corner Post Outer Cover
Intermediate Post (Control)
Intermediate Post Outer Cover #1
Intermediate Post Outer Cover #2
Left Rear Corner Post Outer Cover
Right Rear Corner Post Outer Cover
Vertical Discharge Cover (horizontal discharge only)
Pilot Access Cover
Door Latch

Form P-RDF, Page 34

249
248

CODE Description
240
241
242
243
244
245
246
247
247A
248A
248B
249
250
251
252
253
254
255
256
257
258

Horizontal
Discharge

Front View

Model RDF
2-80 2-120 3-180 3-260
89558
91172
N/A
91173
89559
91174
89562
(2) 91179
203745
204558
(2)89510
(3) 91116
204498
204559
204497
204560
158800
89519
91125
89967
91212
89547
91157
89547
91158
203729
203639
89552
204536
(2) 91163
N/A
203728
203646
203736
203644
203982
204538
204474
203876
124067

250

CODE 270 - Screened Air Inlet Hoods for Outdoor Units and Filter
Sections for Indoor Units
Description
100% Outside Air Inlet Hood (Same as Option AS2)
100% Outside Air Inlet Hood with Integral Filter Rack & 1" Permanent Filters (Same as Option AS6)
100% Outside Air Inlet Hood with Integral Filter Rack & 2" Permanent Filters (Same as Option AS7)
Outside Air Filter Section for Indoor Units with 1" Filters (Same as Option AW3)
Outside Air Filter Section for Indoor Units with 2" Filters (Same as Option AW6)
Components - Outdoor Screened Air Inlet
Cabinets for Models RDF-3 only

RDF-1
69594
69596
72623
69597
72624

RDF-2
68774
68739
72625
68775
72626

Pkg P/N 71150

Pkg P/N 71152

Pkg P/N 72627

Same as Option AS2

Same as Option AS6

Same as Option AS7

Qty
Top of Inlet Hood Cabinet Section
1
Top of Inlet Hood
1
Clamp for Top Seam (Hood to Cabinet)
1
Bottom of Hood Cabinet Section
1
Supports (2 pieces per leg)
6
Left Side of Hood
1
Right Side of Hood
1
Intermediate Posts - Cabinet Section
2
Right Corner Posts - Cabinet Section
1
Left Corner Post - Cabinet Section
1
Doors (Filter Access Section on AS6 and AS7) 2
Center Louver Top/Bottom Supports
2
Pre-assembled Louver Sections with Screens
2
Top and Bottom Filter channels
Filter Block Off Plates
Bottom Filter block Off Plate
Filter Block off Sections
Permanent Filters

P/N
91575
91576
91577
91567
91581
91568
91569
91578
91579
91579
91585
91582
113003
N/A
N/A
N/A
N/A
N/A

Qty
1
1
1
1
6
1
1
2
1
1
2
2
2
2
2
6
12

P/N
91575
91576
91577
91567
91581
91568
91569
91578
91579
91579
91585
91582
113003
91580
91584
N/A
95335
87251, 12x35x1

RDF-3
71150
71152
72627
71153
72628

Qty
1
1
1
1
6
1
1
2
1
1
2
2
2
2

P/N
91575
91576
91577
91567
91581
91568
91569
91578
91579
91579
91585
91582
113003
94224
N/A
1
98764
6
95335
10 94383, 12x35x2

Hardware included in all of the above packages:
Qty P/N Description
100 11813 Sheetmetal Screws #10 x 1/2" long
15 10393 Screws 1/4-10 x 5/8" long (bolt type) - for legs and top clamp
15 7328 Hex Locking Nuts 1/4-20 - for legs and top clamp
3 41463 Sheetmetal Screws #14-10 x 3/4" long - for attaching legs
5 87900 Tinnerman Clips, Palnut #PW-1880-008-21 - for joining louver sections
4 37661 Screws, #10 x 1/2" long (self-drilling) - for attaching middle of doors)

CODE 280 - Roof Curb Packages and Components
Each roof curb package for a Model RDF system includes two curb sides, one front, one back, eight curb dividers for creating supply and return air
ductwork in the curb, and hardware for corner assembly and for installing ductwork dividers.

Roof Curb Option CJ3 for Model RDF Series 3 (See illustration, page 36)
RDF
S eries 3
RDF-1
RDF-2
RDF-3

Pkg
P/N

2 Curb S ide 1 Curb Front
Assembly
and Back Assy

3 , 4 , and 5 - Curb Dividers
for Ductwork

204368

(2)204365

(2)104655

(4)203803 (2)203804 (2)203806

203980
204370

(2)204366
(2)204369

(2)111508
(2)111512

(4)203977 (2)203978 (2)203979
(4)203662 (2)203663 (2)203664

Roof Curb Corner Hardware
For Top Two 8 5/16" x 1" Lag Screws, P/N 16243
8 5/16" Lockwasher, P/N 1333
"Holes"
8 5/16" x 3/4" Hex Head Cap Screw,
For Bottom
P/N 16247
Two "Holes" 8 5/16" Lockwasher, P/N 1333
8 5/16-18 Hex Nut, P/N 1035
Hardware to Assemble and Attach Dividers to make
Ductwork Openings
64
#10 Sheetmetal Screws, P/N 11813
Form P-RDF, Page 35

Roof Curb Packages and Components (cont'd)
Model RDF Series 3 - Reznor Roof Curb and Duct Opening Dimensions
-1
-2
-3
Dimensions of Roof Curb Option CJ3
inches mm inches
mm inches mm
A 84-5/8 2149 84-5/8 2149 131-3/4 3346
B 43-5/8 1108 67-9/16 1716 82-1/16 2084
128
3251
C** 80-7/8 2054 80-7/8 2054
D** 39-7/8 1013 63-13/16 1621 78-5/16 1989
** C and D are roof opening dimensions if curb area
is fully open.

1-7/8 (48)

Roof Curb
Ductwork for
Optional Return Air

RDF

IMPORTANT NOTE: Area enclosed by roof curb must
comply with clearance to combustible materials. If the roof
is constructed of combustible materials, area within the
roof curb must be ventilated; left open, or
1-7/8
covered with non-combustible material which
(48)
has an "R" value of at least 5. If area within curb is
left open, higher radiated sound levels may result.
Roof Curb Duct Opening Dimensions
E
F
G
Sizes
5
inches 23-11/32 20-1/8
RDF-1
593
511
127
mm
inches 28-13/32 28-11/32 13-15/32
RDF-2
722
720
342
mm
38
38
11-19/32
inches
RDF-3
965
965
294
mm

NOTES:
• Drawings are not proportional for all sizes.
• 3/4" (19mm) measurement is the width of the
flanges where the roof curb mates with the
heater. Surface of flanges must be sealed.
• When cutting duct openings in the roof, cut
opening 1” (25mm) larger than duct size
opening for installation clearance.

H
10-1/4
260
7
178
4-5/8
117

Top View

Roof Curb
Ductwork for
Bottom Discharge
(Option AQ1
or AQ3)

Airflow

D

B

(See IMPORTANT
NOTE.)

A

C

J
K
M
25-1/2
11-1/2 11-15/32
648
292
291
54-11/16 17-23/32
8
1389
432
203
66-3/4
20-1/16 10-15/32
1695
510
266
N

1-7/8
(48)

N
11-1/32
280
11-3/32
282
17-1/4
438
F

K

H
G

J

Return
Air
Opening
(J x K)

Top View

Airflow

3/4 (19)

Bottom
Discharge
Supply Air
Opening
(E x F)

E

3/4 (19)

M

Assembled Dividers for Optional
Return Air Ductwork in the Roof Curb
Field-supplied ductwork may be either
“dropped in” from the top resting on
the top flange or be attached to the bottom
flange, using the dividers as ductwork.

(800) 695-1901; www.RezSpec.com
Form P-RDF, Page 36

©2005 Thomas & Betts Corporation, All rights reserved.
Printed in U.S.A.
MANUFACTURER OF GAS, OIL, ELECTRIC HEATING AND VENTILATING SYSTEMS
9/05 Form P-RDF (Version A.1)



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2005:09:02 14:12:15-04:00
Subject                         : P-RDF Version A.1
Author                          : REAGLKC
Modify Date                     : 2005:09:02 14:12:40-03:00
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Keywords                        : 
Creator Tool                    : Adobe PageMaker 7.0
Format                          : application/pdf
Title                           : P-RDF Version A.1
Creator                         : REAGLKC
Description                     : P-RDF Version A.1
Document ID                     : uuid:21c91c46-5904-4b2e-98aa-7a0baad483bd
Instance ID                     : uuid:545e1ca6-1f47-4f2c-afef-73dc2a30e4a8
Page Count                      : 36

EXIF Metadata provided by EXIF.tools