75438_1 ENG 101006 Catalog

2014-07-30

: Pdf 101006-Catalog 101006-Catalog 786210 Batch6 unilog

Open the PDF directly: View PDF .
Page Count: 176 [warning: Documents this large are best viewed by clicking the View PDF Link!]

T&B Conduit Fittings

Table of Contents

Specifications for Rigid Metal Conduit 5-10

Locknuts, Sealing Fittings, 11, 12

Bonding and Grounding Wedges

Bushings 13-19

Knockout Plugs 20–21

Chase ®Nipple 22-2222-23

Threaded Bullet ®Hubs 24-27

T&B Hub 28-31

Threadless Fittings/Couplings 32-34

Set Screw Fittings/Couplings 35, 36

Short Elbows 37

Erickson ®Threaded Couplings 38-40

Conduit Straps and Spacers 41-44

Combination Couplings, 45

Beam Clamps, Conduit Supports

Methods of Bonding and Grounding 46-53

Rigid and Intermediate 5-53

Metal Conduit Fittings

Specifications for EMT 54-56

EMT Fittings 57-59

Electrical Metal Tubing 54-59

(EMT) Fittings

Specifications for Flexible 60-62

Cord and Cable

Selection Guide 63, 64

Specifications for Liquidtight 65

Flexible Cord and Cable Fittings

Strain Relief Fittings 66-69

Ranger ™Series Liquidtight 70, 71, 73, 75

Strain Relief Fittings

Aluminum Liquidtight Strain 72

Relief Fittings

SS Liquidtight Conduit Connectors 74

Silver Grip™—TCF™Series 76, 77

Tray-Cord Fitting

Silver Grip™Liquidtight Fittings 78, 79

iremesh Grips 80

Nonmetallic Cable Glands 81

Metric Adapters, Fittings and Plug 82

Flexible Cord and Cable Fittings 60-82

General Information 4

1-e.pdf 1 11/28/2011 11:24:25 AM

CONFITMRO_EN_ALL.pdf 2 11/28/2011 11:05:17 AM

Armoured Cable and Flexible 111-119

Metal Conduit Fittings

Nonmetallic Sheathed 120-126

Cable Fittings

Liquatite ®Flexible Conduit 127-155

Conduit Dimensional Data 156, 157

Conduit Chemical Resistance Guide 158-161

Alphanumeric Index 162-175

T&B Conduit Fittings

Table of Contents

Specifications 83-85

Service Entrance Cable Fittings 86, 87

Service Entrance Cable Fittings 83-87

Liquidtight Flexible Conduit Fittings 88-110

Specifications for Armoured 111-114

Cable and Flexible Metal Conduit

Fittings for Armoured Cable 115-119

and Flexible Metal Conduit

Specifications for Nonmetallic 120, 121

Sheathed Cable Fittings

Fittings for Nonmetallic Sheathed 122, 126

Cable Fittings

Application Guide 127,128

Steel 129-135, 137, 139

142, 144, 145

Aluminum 136, 138, 143

Shielding 140, 141

Nonmetallic 146, 147

Corrlok®System 148-152

Engineering Information 153, 154

Packaging 155

Specifications for Liquidtight 88-90

Flexible Metal Conduit

High Temperature Flexible 91

Metal Liquidtight Fittings

Liquidtight Flexible Metal 92-100, 103-106, 109

Conduit Fittings

Specifications — Type A Nonmetallic 101

Conduit Fittings

Liquidtight Flexible Nonmetallic 101, 102, 107, 108

Conduit Fittings

ISO Metric BulletTM Liquidtight Fittings 110

CONFITMRO_EN_ALL.pdf 3 11/28/2011 11:05:17 AM

General Information

T&B Conduit Fittings

Thomas & Betts…

The Complete Product Line

Since the turn of the century, Thomas & Betts

has been a recognized leader in electrical

fittings. Industry standards such as Chase®

Nipples and Erickson®Couplings were

introduced by Thomas & Betts and are

still registered trademarks. This leadership

continues. Here’s why.

Innovative Designs

The real test of product design of

electrical fittings lies in two areas: job-

suited installation and life-of-the-job

reliability. Thomas & Betts Fittings

provide both because we listen. We listen

to problems and suggestions from the

field. Most of the products in this section

result from the good suggestions of

knowledgeable electrical people. Many

were custom designed to solve a

customer’s particular installation and

performance problems. You can

benefit from their experience.

Approvals and Certifications

Electrical raceways require accessory

fittings that provide the mechanical

strength, ground continuity, and

environmental integrity of the system.

As new raceways have been

introduced, Thomas & Betts, engineers

have designed fittings which meet the

requirements of the Canadian Electrical

Code, as well as

the

Canadian

Standards Association. You can use

Thomas & Betts Fittings with confidence.

Note: All dimensions in this catalogue are

approximate.

High Performance Products

Quality and performance result

when engineering design skills are

combined with the manufacturing

technologies

required to produce them.

The Thomas & Betts

Fittings in this

section are produced from many

materials and by many manufacturing

methods, each carefully selected for its

end use suitability. This combination

gives you the reliable performance you

expect from Thomas & Betts

Raceway Fittings.

Lower Installed Cost

Lower installed cost is a function of

purchase cost, availability, installation

advantage, and performance; it

comes in

every carton of Thomas & Betts

Raceway

Fittings.

CONFITMRO_EN_ALL.pdf 4 11/28/2011 11:05:17 AM

Specifications — Rigid Metal Conduit/PVC Coated Rigid Metal Conduit

T&B Conduit Fittings

Rigid Metal Conduit Fittings

Ref. CEC Rule 12-1000

Rigid Metal Conduit affords maximum

mechanical protection to conductors

within the raceway. Rigid metal conduit

can be installed indoors and outdoors, in

dry locations or wet locations, exposed or

concealed, in all atmospheric conditions

and in hazardous locations.

Galvanized rigid steel conduit

installed in concrete does not require

supplementary corrosion protection.

Galvanized rigid steel conduit, installed in

contact with soil, does not generally

require supplementary corrosion

protection. However, when buried in

corrosive soil (corrosive soil is

characterized by low resistivity of less

than 2,000 ohm-centimeter) or cinders, a

protective coating of bitumastic, asphalt-

based paint or a PVC coating is applied

to the conduit. CEC Rule 12-934

requires that rigid steel conduit installed in

or under permanently moist cinder fill be

encased in at least two inches of

cinder-free concrete unless the conduit is

at least 18 inches below the fill. Steel

conduit protected from corrosion solely by

enamel can only be used indoors and in

occupancies not subjected to severe

corrosive influences.

Rigid nonferrous metal conduit

(aluminum) cannot be directly

embedded in concrete containing

soluble chlorides such as calcium

chloride; unwashed beach sand,

seawater, or coral bearing aggregates.

However, if adequately treated by a

protective coating of bitumastic or

asphalt-based paint or PVC coating, the

conduit can be installed in concrete

containing chlorides.

Supplementary nonmetallic coatings

presently used on ferrous rigid metal or

nonferrous metal have not been

investigated for resistance to corrosion.

CEC Rule 12-920 requires that when

conduit enters a box or fitting, a bushing

must be provided to protect wires from

abrasion unless the design of the box or

fitting provides equivalent protection.

According to CEC Rule 12-906

where No. 8 or larger ungrounded

conductors enter or leave a conduit, an

insulating bushing with a smooth well

rounded insulating surface must be

provided to protect conductors unless

the terminating fitting is equipped with an

insulated throat, firmly secured in place

providing equivalent protection. The

insulating bushing or insulating material

must have a temperature rating of not less

than the insulation temperature rating of

installed conductors. When conduit

bushings are constructed wholly of

insulating material, a locknut must be

installed both inside and outside of the

enclosure to which the conduit is

attached.

Fittings and couplings are required

to be of concrete-tight type when

embedded in masonry or concrete or in

dry locations and of the raintight type

when installed in wet locations.

In wet locations or locations

where walls are frequently washed or

where there are surfaces of absorbent

materials, the entire wiring system

including boxes, fittings, conduit and

cables must be supported such

that there is at least 1/4 inch air space

between it and the supporting surface

(CEC Rule 2-122).

CEC Rule 12-3022 requires that the

raceways be metallically joined together

into a continuous electric conductor

and must be mechanically connected to

all boxes, fittings and cabinets as to

provide effective electrical continuity.

Conduit is required to be supported

adequately and conduit bends in

one run are restricted to the equivalent

of four quarter i.e. 360 degrees total.

Listed below are some of the

advantages of rigid aluminum conduit

over rigid steel conduit.

1. Non-sparking—eliminates hazard in

explosive atmospheres

2. Non-magnetic—reduces power loss

due to voltage drop

3. Resists most corrosive atmospheres

and industrial environments

4. Lightweight—reduces cost

of handling and installation

5. Attractive appearance

CONFITMRO_EN_ALL.pdf 5 11/28/2011 11:05:17 AM

T&B Conduit Fittings

Rigid Metal Conduit Fittings

For further details and complete

information please refer to the following:

1. ANSI C80.1…Rigid Steel Conduit

Zinc Coated, Specifications for

2. ANSI C80.2…Rigid Steel Conduit,

Enameled, Specifications for

3. ANSI C80.5…Rigid Aluminum

Conduit. Specifications for

4. ANSI C80.4…Fittings for Rigid Metal

Conduit and Electrical Metallic

Tubing, Specifications for

5. WW-C-581…Federal Specification,

Conduit, Metal, Rigid & Coupling,

Elbow, and Nipple, Electrical

Conduit, Zinc Coated

6. WW-C-540…Federal Specification,

Conduit, Metal, Rigid (Electrical,

Aluminum)

7. WW-C-571…Federal Specification,

Conduit, Metal, Rigid, and Coupling,

Elbow, and Nipple, Electrical

Conduit Enameled

8. U.L. 6…Standards for Safety. Rigid

Metal Conduit

9. U.L. 2142…Standards for Safety.

Intermediate Metal Conduit

10. CEC Section 12-1000…Rigid and

Flexible Conduit

11. CSA C22.2 No. 45…Safety

Standards for Rigid Metal Conduit

12. CSA C22.2 No. 18…Safety

Standards for Outlet Boxes,

Conduit Boxes and Fittings

13. NEMA FB-1…Standards

Publication. Fittings and Supports

for Conduit and Cable Assemblies

14. A-A-50553 Federal Specification.

Fittings for Conduit Metal Rigid

(Thickwall & Thinwall [EMT] Type)

Please Note

The excerpts and other material herein, whether relating to the

Canadian Standards Association, the Underwriters Laboratories, Inc.

listing, to industry practice or otherwise, is not intended to

provide all relevant information required for use and installation.

Reference to original or primary source material and data is

mandatory before any application or use is made of the product.

Specifications —Rigid Metal Conduit/PVC Coated Rigid Metal Conduit (continued)

CONFITMRO_EN_ALL.pdf 6 11/28/2011 11:05:17 AM

T&B Conduit Fittings

Rigid Metal Conduit Fittings

• Rigid ferrous metal conduit or PVC

coated rigid conduit prior to coating

shall be of the hot dipped galvanized

type adequately protected against

corrosion inside and outside including

threads, and conforming to the

following applicable specifications:

-Rigid Ferrous Metal Conduit Federal

Specification WW-C-581/ANSI

C80.1/U.L. 6/CSA C22.2 No. 45

-PVC Coated Ferrous Metal Conduit

Applicable listed under (i) and in

addition conforming to NEMA

Publication No. RNI-2005 (Type A)

PVC coating on conduit and asso-

ciated fittings shall have no sags,

blisters, lumps or other surface

defects and shall be free of holes.

• Rigid nonferrous metal conduit shall

conform to Federal Specification

WW-C-540/ANSI C80.5/U.L. 6/CSA

C22.2 No. 45.

• All field cuts shall be square, reamed

and deburred. Conduit threads shall

be tapered for entire length with 3¼4”

taper per ft. Conduit threads prior to

assembly shall be clean and coated

with grease metallic type conductive

compounds such as series CP8

KOPR-SHIELD for ferrous conduit or

series AP8 ALUMA-SHIELD for

nonferrous

(aluminum) conduit as manufactured

by Thomas & Betts.

• To prevent ingress of plaster, dirt,

trash or moisture in raceways, boxes,

fittings and equipment during course

of construction, all open ends shall

be closed with rugged thermoplastic

plugs as manufactured by Thomas &

Betts, series 1470 and 1451. Plugs

shall be firmly secured in place to

provide adequate seal and shall be

functionally unaffected by moisture.

Thermoplastic plugs shall be rated at

105°C/221°F and have a U.L.

flammability rating of 94V-1.

Cat. #CP8

KOPR-SHIELD*

* TM of Jet-Lube, Inc.

Cat. #AP8

ALUMA-SHIELD ®

Series 1451

Knockout Plug

Series 1470

Plug, Conduit/Fitting

Suggested Specifications for Rigid Metal Conduit/PVC Coated Rigid Metal Conduit

and Fittings meets 2009 CEC Rule 2-112

CONFITMRO_EN_ALL.pdf 7 11/28/2011 11:05:18 AM

T&B Conduit Fittings

Rigid Metal Conduit Fittings

Suggested Specifications for Rigid Metal Conduit/PVC Coated Rigid Metal Conduit

and Fittings (continued)

Series 1276

Conduit Strap

Series 700

Adjustable Beam

Clamp

Series 1350

Conduit Spacer

Series 5302

Sealing Gasket

Series 370

Threaded Hub

(Raintight)

Series 485 PVC

Coated Threaded

Hubs (Raintight)

Series 8123

Threadless Fitting

(Concretetight)

Series 8120

Threadless Coupling

(Concretetight)

Series 8125

Set Screw Fitting

(Concretetight)

Series 8124

Set Screw Fitting

(Concretetight)

Series 140

Locknut

Series 106

Bonding Locknut

Series 690

Conduit Supports

• Conduit shall be securely fastened in

place, at intervals as specified by the

code, using suitable straps, hangers

and other supporting assemblies as

indicated on plans and as

manufactured by Thomas & Betts,

series 1276, 690 and 700. All strap

hangers and supporting assemblies

shall be of rugged construction

capable of supporting weight with a

reasonable factor of safety and shall

be adequately protected against

corrosion. Where applicable, it shall

conform to Canadian Standards

Association Standard C22.2 No. 18.

• In wet locations or in locations where

corrosive conditions are present,

vertical and horizontal runs of conduit

shall be firmly supported so that

there is at least 1¼4” air space

between the conduit and the wall

or supporting surface. Spacers and

supporting straps shall be of

malleable iron construction, hot

dipped galvanized conforming to

Canadian Standards Association

Standard C22.2 No. 18 such as

Thomas & Betts series 1276 straps and

series 1350 spacers. Nonferrous metal

straps and spacers may be

substituted as required.

• Where threaded conduit terminates

into a threadless opening, a locknut

shall be provided both inside and

outside the box or enclosure and

the conduit end shall be fitted with

an insulating bushing. In wet

locations, a suitable gasket shall

be provided between the outside

locknut and the opening.

Locknuts shall be rugged, of

hardened steel or malleable iron

construction, electro-zinc plated

and capable of cutting through

protective coating on box or

enclosure to ensure positive bond

such as Thomas & Betts series 140.

• Where raceway and associated

fittings are used as part of an

equipment grounding system,

terminating fittings shall be equipped

with bonding type locknuts such as

Thomas & Betts series 106 bonding

locknuts.

Sealing gaskets shall be

constructed of oil resistant/moisture

resistant rubber and shall be suitably

protected by and permanently

bonded to a stainless steel retainer

such as Thomas & Betts series 5302.

• Where threaded rigid metal conduit is

installed outdoor or indoors or in

locations exposed to continuous or

intermittent moisture, a sealing hub

type terminating fitting shall be installed.

Hubs shall be of malleable iron/steel

construction, electro-zinc plated and

equipped with a nylon insulated throat

and oil resistant/moisture resistant

sealing ring as manufactured by

Thomas & Betts, series 370 or series

H050-TB. Female taper hub threads

shall be adequately relieved to prevent

bottoming of conduit.

Hubs constructed of copper-free

aluminum may be substituted when

used with rigid nonferrous (aluminum)

metal conduit, Thomas & Betts series

370AL or H050A.

For environmental conditions that

are more than normally corrosive

to exposed surfaces, hubs suitably

protected with PVC coating such

as Thomas & Betts series 485 shall

be used.

CONFITMRO_EN_ALL.pdf 8 11/28/2011 11:05:18 AM

T&B Conduit Fittings

Rigid Metal Conduit Fittings

Suggested Specifications for Rigid Metal Conduit/PVC Coated Rigid Metal Conduit

and Fittings (continued)

• Where concrete-tight requirements

must be met, or in dry locations, rigid

metal conduit or intermediate metal

conduit fittings and couplings shall

be of the concrete-tight type. Fittings

shall be rugged, of ferrous metal

construction, electro-zinc plated

inside and outside, and furnished

with a nylon bushing as

manufactured by Thomas & Betts,

series 8123 and 8120. Insulated set

screw type fittings such as Thomas &

Betts series 8125 and 8124 may be

substituted unless otherwise

indicated on drawings.

Components critical to performance

such as set screws, split rings, and

locknuts shall be hardened or

adequately designed to ensure

positive bond between conduit

and enclosure or conduit runs.

All fittings of the system shall be

capable of carrying ground fault

currents per the following:

1/2” through 1-1/2” size…10,000 amps

RMS (duration of fault current 3 cycles)

2” and above…20,000 amps RMS

(duration of fault current 3 cycles)

• All back-to-back nippling of boxes

shall be done using locknuts and nylon

bushed nipples as manufactured by

Thomas & Betts, series 140 locknuts

and series 1942 nipples. Nipples, or

suitably designed bushings such as

Thomas & Betts series 3210, shall also

be used where conductors pass

through either factory or field punched,

cut or drilled holes in metallic

members.

• Where neither length of threaded

conduit can be rotated, couplings

such as Thomas & Betts series 674

shall be installed in conduit runs.

• Where threaded or threadless

conduit terminates outside a box

or an enclosure, or where conduit is

stubbed up, it shall be equipped with

an insulated metallic or nonmetallic

bushing such as Thomas & Betts series

1222 or TRIB50.

• Where code requires bonding and

grounding of single or multiple rigid

metal conduits or where positive

bonding and grounding of conduit to

the box, enclosure or auxiliary gutter

is required, the end of the conduit

shall be equipped with an insulated

metallic grounding and bonding

bushing such as Thomas & Betts

series 3870.

Insulated metallic grounding and

bonding bushing shall be approved for

the purpose. It shall be of malleable

iron/steel construction adequately

protected against corrosion,

assembled

with an insulator listed or certified for

150°C/302°F application and

flammability rating of 94V-0 with

insulator positively secured in place.

Bonding to enclosure shall not be

dependent on locknut bushing type

contact but by a positive bonding

means such as a hardened screw or

equivalent.

Series 140

Locknut

Series 1942

Insulated Nipple

Series 3210

Knockout Bushing

Series 674

Threaded Coupling

Series 222TB

Insulating Bushing

Series TRIB50

Threadless Rigid

Insulating Bushing

Series 3870

Insulated Grounding &

Bonding Bussing

CONFITMRO_EN_ALL.pdf 9 11/28/2011 11:05:18 AM

T&B Conduit Fittings

Rigid Metal Conduit Fittings

140 Series

141AL Series

106 Series

Specifications — Locknuts

Application

• To connect externally threaded

conduit or fitting to a threadless

opening in a box or enclosure.

• To effectively bond conduit or

fitting to box or enclosure.

Features

• Hardened Steel/Malleable Iron/

Copper-free Aluminum construction.

• Tightens without deformation.

• Locknuts specially designed to:

(i) Provide extended reach for

clamping on thin boxes and

enclosures

(ii) Cut through protective coating on

box and enclosure thereby

ensuring ground continuity

(iii) Permit tightening from outside

(iv) Prevent loosening under vibration

• 106 Series provided with a hardened

cone point screw.

Standard Material

140 Series & 106 Series

3¼8” thru 2” Steel (hardened)

2-1/2” thru 6” Malleable Iron

All screws steel

141AL Series

All copper-free aluminum

(less than .4% copper)

Standard Finish

All Steel and Malleable Iron locknuts

including bonding screws

..........................Electro-zinc Plated

All Aluminum locknuts . . . . . . . .degreased

For chromate coating use prefix 040

Range

• 3/8” through 6” conduit (all threads

straight pipe [NPS]) (140 Series)

• 1/2” through 4” conduit (106 Series

& 141AL Series)

Conformance

U.L. 514B

CSA C22.2 No. 18.3

NEMA FB-1

ANSI C80.4

Federal Specification W-F-408

Federal Standard H-28 (Threads)

“Case Hardened Locknuts”

Case hardened locknuts make fittings

faster and easier to install. Case

hardened locknuts do not slip or turn

thereby protecting the biting edge.

Case hardened locknuts bite through

the paint on the enclosure providing

excellent continuity of ground (typical

T&B/ Thomas & Betts fitting with case

hardened locknuts successfully passed

minimum fault current of 10,000 amps

RMS). Case hardened locknuts when

assembled in the intended manner

will not vibrate loose thereby ensuring

excellent ground continuity.

CONFITMRO_EN_ALL.pdf 10 11/28/2011 11:05:18 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Locknuts

Cat. No. Dimensions (in.)

Stl. or M.I. Alum. SST Size A B

139*†—— 1/4” 27/32 5/32

140* — — 3/8” 15/16 5/32

141** 141AL 141SST 1/2” 1-7/64 5/32

142-TB** 142AL 142SST 3/4” 1-3/8 3/16

143 143AL 143SST 1” 1-11/16 13/64

144 144AL 144SST 1-1/4” 2-5/32 13/64

145 145AL 145SST 1-1/2” 2-1/2 13/64

146-TB 146AL 146SST 2” 3 7/32

147 147AL 147SST 2-1/2” 3-9/16 13/32

148 148AL 148SST 3” 4-3/16 13/32

149 149AL 149SST 3-1/2” 4-13/16 15/32

150 150AL 150SST 4” 5-5/16 15/32

151 151AL 151SST 4-1/2” 5-15/16 17/32

152 152AL 152SST 5” 6 -1/2 17/32

153 153AL 153SST 6” 7-3/4 17/32

* Hex shape

** Case hardened locknuts

Aluminum locknuts comply with federal standard of copper-free aluminum; less than .4% copper.

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

† Not UL or CSA certified

Bonding Locknuts

Dimensions (in.)

Cat. No. Size Screw Sizes A B

106 1/2” 8-32x 7/16” 1-3/8 .125

107 3/4” 8-32x 7/16” 1-5/8 .140

108 1” 8-32x 7/16” 1-15/16 .170

109 1-1/4” 8-32x 7/16” 2-5/32 .170

110-TB 1-1/2” 8-32x 7/16” 2-1/2 .170

111 2” 8-32x 7/16” 3 .187

112-TB 2-1/2” 1/4-20x 5/8” 3-13/32 .375

113-TB 3” 1/4-20x 5/8” 4-13/16 .375

114 3-1/2” 1/4-20x 5/8” 4-29/32 .438

115-TB 4” 1/4-20x 5/8” 5-7/16 .438

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Steel finish: zinc plated

Sealing Fittings

Dimensions (in.)

Cat. No. Size A B C

141SL 1/2 1.140 1/8 1/4

142SL 3/4 1.420 5/32 9/32

143SL 1 1.770 11/64 9/32

144SL 1-1/4 2.281 11/64 5/16

145SL 1-1/2 2.598 11/64 9/32

146SL 2 3.175 3/16 19/64

Steel finish: zinc plated

Steel or malleable iron (steel thru 2”)

or Aluminum 624

Many of the T&B standard conduit and cable

fittings are furnished with “case hardened

locknuts”. This exclusive feature means the

locknut tightens up against the box without

deforming; the locknut bites into the box

providing a positive ground; the fitting can

be tightened from outside the box.

Steel or malleable iron (steel thru 2”).

Use anywhere an ordinary locknut is installed to

ensure positive bonding of conduit to box and

prevent loosening due to vibration. Also can be

used for Service Entrance applications in

conformance with Code. T&B rigid conduit and

E.M.T. (thinwall) fittings comply with Federal

Specification WF 408c.

Molded Santoprene Seal

Color: Blue

Provides positive seal against water and oil. For

use with rigid and intermediate metal conduits,

or fittings to provide watertight or raintight seal

at all enclosures. NPS threads.

(B) Thickness

(B)

Thickness

11-e.pdf 1 2/2/2012 10:36:32 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Sealing Rings with Stainless Steel Retainer

Conduit Dimensions (in.)

Cat. No. Size A B ± 1¼64

5302 1/2” 1-11/64 3/4

5303 3/4” 1-1/2 15/16

5304 1” 1-3/4 1-11/64

5305 1-1/4” 2-9/64 1-1/2

5306 1-1/2” 2-27/64 1-3/4

5307 2” 2-59/64 2-15/64

5308 2-1/2” 3-7/16 2-43/64

5309 3” 4-5/64 3-19/64

5311 4” 5-9/32 4-19/64

NEMA 3R, 4, 6 and 13

Bonding & Grounding Wedges

Bonding and Grounding Wedges

Cat. No. Size

3650 1/2”

3651 3/4”

3652 1”

3653 1-1/4”

3654 1-1/2”

3655 2”

3656 2-1/2”

3657 3”

3658 3-1/2”

3659 4”

3661 5”

3662 6”

Sealing Ring-Santoprene

Thermoplastic Rubber

These sealing rings provide a liquid tight, dust

tight, seal of fitting at enclosures.

Series 3651

Especially suited for grounding old work, but

equally convenient for new, grounding wedges

provide grounding without a jumper except in

concentric knockouts. When a jumper is required, it

fits under a set screw in the grounding wedge.

Update existing installations to meet code

requirements for bonding (CEC Section (10-806)

without disconnecting wiring. Use on new

wiring also.

1. Loosen bushing and position wedge.

2. Tighten bushing and bonding screw.

Series 3650

Application

To effectively bond terminating fitting or

conduit to a box or enclosure.

Features

• Sizes 3/4” thru 6” equipped with an

additional bonding screw to install

bonding jumper where required.

• Can be added to an existing installation

without disconnecting conductors.

Standard Material/Finish

1/2” size ............Steel/Electro-zinc Plated

3/4” thru 6” size..........Bronze/Tin Plated

Range

1/2

” thru 6” conduit

Conformity

U.L. 467

C.S.A. C22.2 No. 41

NFPA70-2008 (ANSI)

Federal Specification A-A-50552

CONFITMRO_EN_ALL.pdf 12 11/28/2011 11:05:19 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Blackjack®— Conduit Grounding Bushings

Innovative design makes installation

quicker, easier.

The Blackjack®Grounding Bushing

never has to be threaded onto a

conduit. It is simply placed in position on

either a threaded or non-threaded rigid or

IMC conduit, with the grounding lug in

perfect position to accept the

grounding

wire. Even in tight installations,

it’s as

simple as one, two, three. Compare

the installation with conventional

bushings that must be threaded onto

the conduit. In tight areas, you may

have to remove the grounding lug,

keep up with the loose parts, and then

reattach the lug. Then you still have to

twist and turn the bushing to get the

lug in position to accept the grounding

wire. The Blackjack bushing does

away with these needless delays for

good, making it the ideal grounding

bushing and the only logical choice for

small spaces, corners, and multiple

conduit runs. And, because the

grounding lug is an integral part of the

bushing, it is designed not to fall off or

get lost.

Innovative design improves

performance.

The Blackjack®bushing provides

superior ground continuity.

The design of the Blackjack bushing

has an integral, cast-on grounding lug

for better ground continuity. This

means that the Blackjack bushing

stands up to intense loads.

Secure grip

forms lasting

bond.

The Blackjack

bushing’s cone-

point mounting

screw bites

securely into both

threaded and

non-threaded rigid conduits. And the

Blackjack bushing’s nylon locking patch

is designed to prevent the screw from

loosening due to vibration.

Reduce inventory.

Because the Blackjack Grounding

Bushing is designed for threaded and

non-threaded conduits, and the ground

lugs are designed to handle an

extended range, the number of parts in

inventory is reduced by up to two-thirds

without losing any application coverage.

Mounting

screw with

nylon locking

patch has a

cone point to

lock bushing

securely in

place.

Insulator surface

features a rounded

design to reduce

drag and prevent

abrasion during

wire pulling.

Cast “threads”

opposite the

mounting screw

tighten the fit

during installation.

Angle of lug

screw improves

accessibility

when securing

grounding wire.

Integral grounding

lug enhances

ground continuity.

Added ground

wire range taking

reduces inventory.

Accepts copper or

aluminum ground

wires.

Insulating nylon

surface is 150°C

rated and covers

top of bushing,

including lug

corners.

Blackjack®– Conduit Grounding Bushing

Lug Screw:

14-4: Slotted

14-2/0: Slotted

6-4/0: Internal Hex Drive

Standard Material/Finish

Body: Malleable Iron or Aluminum

Mounting Screw: (1/2"-2") Stainless

Steel, (2-1/2"-6") Brass

Lug Screw: Stainless Steel

Finish: Zinc Plated or Mechanical

Galvanized

Range

Conduit: 1/2 thru 6" threaded or

threadless rigid/IMC

Wire Range: #14 AWG to 4/0 AWG

CU/AL

Conformity

U.L. 514B & U.L. 467

CSA C22.2 No. 18.3 & CSA C22.2

No. 41

CONFITMRO_EN_ALL.pdf 13 11/28/2011 11:05:19 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Cat No.

Zinc Conduit Dim.

Plated Size ØA ØB ØC ØD E Wire

Malleable Iron Aluminum in. Max. Max. Max. Max. Max. Range

BG050-14-20 BGA050-14-20 1/2 1.251 .569 1.181 2.134 .696 14-2/0

BG050-14-4 BGA050-14-4 1/2 1.251 .569 1.027 1.940 .696 14-4

BG075-14-20 BGA075-14-20 3/4 1.533 .772 1.221 2.414 .696 14-2/0

BG075-14-4 BGA075-14-4 3/4 1.533 .772 1.030 2.168 .696 14-4

BG100-14-20 BGA100-14-20 1 1.783 .993 1.181 2.581 .696 14-2/0

BG100-14-4 BGA100-14-4 1 1.783 .993 1.027 2.368 .696 14-4

BG125-14-20 BGA125-14-20 1-1/4 2.220 1.319 1.181 2.987 .759 14-2/0

BG150-14-20 BGA150-14-20 1-1/2 2.470 1.553 1.181 3.236 .696 14-2/0

BG200-14-20 BGA200-14-20 2 2.830 2.010 1.181 3.766 .696 14-2/0

BG250-14-20 BGA250-14-20 2-1/2 3.148 2.412 1.181 4.341 .978 14-2/0

BG250-6-40 BGA250-6-40 2-1/2 3.148 2.412 1.524 4.526 .978 6-4/0

BG300-14-20 BGA300-14-20 3 4.042 3.022 1.181 4.966 .978 14-2/0

BG300-6-40 BGA300-6-40 3 4.042 3.022 1.524 5.139 .978 6-4/0

BG350-14-20 BGA350-14-20 3-1/2 4.542 3.491 1.181 5.467 .978 14-2/0

BG350-6-40 BGA350-6-40 3-1/2 4.542 3.491 1.524 5.639 .978 6-4/0

BG400-14-20 BGA400-14-20 4 5.042 3.975 1.181 5.966 .978 14-2/0

BG400-6-40 BGA400-6-40 4 5.042 3.975 1.524 6.139 .978 6-4/0

BG500-14-20 BGA500-14-20 5 6.136 4.991 1.181 7.045 .978 14-2/0

BG500-6-40 BGA500-6-40 5 6.136 4.991 1.524 7.207 .978 6-4/0

BG600-14-20 BGA600-14-20 6 7.199 6.009 1.181 8.087 .978 14-2/0

BG600-6-40 BGAT600-6-40 6 7.199 6.009 1.524 8.409 .978 6-4/0

Suggested Specifications

Insulated grounding and bonding bushing

(Series BG050-BG600)

Where code requires bonding and grounding of single or multiple metal conduits, or positive bonding and grounding of metal conduit to the

box, enclosure or auxiliary gutter, the end of the conduit shall be equipped with an insulated metallic grounding and bonding bushing series

BG050-14-20 as manufactured by Thomas & Betts.

Grounding and bonding bushings used shall be approved for the purpose and

(i) Shall be of malleable iron/steel/aluminum construction adequately protected against corrosion.

(ii) Bushing insulator shall be listed or certified for 150°C/302°F application with a flammability rating of 94V-O. Insulator must be positively

locked in place.

* Mechanical galvanization is available in the 3870 Series; add suffix MG to Cat. No.

Blackjack®— Conduit Grounding Bushings

Cat No.

Lug Screw

14-4: Slotted

14-2/0: Slotted

6-4/0: Internal hex drive

For Threaded & Threadless Rigid & IMC Conduit.

Nylon Insulator (150oC) Mounting Screw

ØA

ØB

Throat I.D.

CONFITMRO_EN_ALL.pdf 14 11/28/2011 11:05:19 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Threaded Insulated Grounding Bushing

Wire

Range

Conduit Bushing Throat Lug Swing Bushing AWG

Cat. No. Size Dia. Dia. Length Radius Height CU/AL

3870-TB 1/2 1.125 .560 1.310 1.212 .657 14-4

3861 1/2 1.125 .560 1.675 1.402 .657 8-2/0

3871-TB 3/4 1.420 .742 1.310 1.360 .660 14-4

3862 3/4 1.420 .742 1.675 1.550 .660 8-2/0

3872 1 1.770 .944 1.310 1.535 .735 14-4

3882 1 1.770 .944 1.675 1.725 .735 8-2/0

3873 1-1/4 2.190 1.242 1.310 1.745 .735 14-4

3883 1-1/4 2.190 1.242 1.675 1.935 .735 8-2/0

3874 1-1/2 2.468 1.449 1.310 1.884 .770 14-4

3884 1-1/2 2.468 1.449 1.675 2.074 .770 8-2/0

3875 2 3.031 1.860 1.310 2.165 .770 14-4

3889 2 3.031 1.860 1.675 2.355 .770 8-2/0

3876 2-1/2 3.516 2.222 1.310 2.408 .940 14-4

3886 2-1/2 3.516 2.222 1.675 2.598 .940 8-2/0

3993 2-1/2 3.516 2.222 2.230 2.928 .940 6-4/0

3877 3 4.234 2.761 1.310 2.767 .975 14-4

3887 3 4.234 2.761 1.675 2.957 .975 8-2/0

3994 3 4.234 2.761 2.230 3.287 .975 6-4/0

3878 3-1/2 4.781 3.193 1.310 3.040 .975 14-4

3863 3-1/2 4.781 3.193 1.675 3.230 .975 8-2/0

3995 3-1/2 4.781 3.193 2.230 3.560 .975 6-4/0

3879 4 5.328 3.623 1.310 3.314 .980 14-4

3864 4 5.328 3.623 1.675 3.504 .980 8-2/0

3996 4 5.328 3.623 2.230 3.834 .980 6-4/0

3880 5 6.328 4.542 1.310 3.814 .985 14-4

3865 5 6.328 4.542 1.675 4.000 .985 8-2/0

3998 5 6.328 4.542 2.230 4.334 .985 6-4/0

3881 6 7.406 5.458 1.310 4.353 1.200 14-4

3866 6 7.406 5.458 1.675 4.543 1.200 8-2/0

3999 6 7.406 5.458 2.230 4.875 1.200 6-4/0

Temperature rating 150°C.

Meets Coast Guard Regulation CG293

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

*Contact customer service for copper lay in lug

Application

• For quick installation of bonding

jumper to multiple metal conduits

(Rigid and IMC).

• Designed to bush conductors and

prevent insulation damage.

Features

• Ease of installation, lay in lug design.

• Cast malleable iron body designed to

lock insulator in place within body

reducing common assembly problem

resulting in dislodging of insulator.

• Insulator rated for 150°C/302°F

application.

Standard Material / Finish

Body: Electro-zinc plated

Lay-in lug: Aluminum/tin plated

Insulator: Thermoplastic

150°C/302°F

Application with 94V-0 flammability.

Wire

Clamping Screw

Insulator

Set-Screw

(one)

Lay-In*

Lug

Bushing

Casting

CONFITMRO_EN_ALL.pdf 15 11/28/2011 11:05:20 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Insulated Throat Fittings

Dimensions (in.)

Cat. No. Size A B

1222 1/2” 1-1/32 29/64

1223 3/4” 1-9/32 31/64

1224 1” 1-19/32 19/32

1225 1-1/4” 1-15/16 21/32

1226 1-1/2” 2-3/16 23/32

1227 2” 2-11/16 7/8

1228 2-1/2” 3-3/16 31/32

1229 3” 3-27/32 15/16

1230 3-1/2” 4-7/16 1-1/16

1231 4” 4-7/8 1-3/32

1232†4-1/2” 5-7/16 1-15/64

586 5” 5-31/32 1-9/32

587 6” 7-3/16 1-11/32

†Not CSA Certified

Catalogue series 1222 thru 1232, 586 and 587 are available in aluminum. Add suffix AL to

Cat. No. The aluminum series are not CSA certified.

Metallic Bushings

Cat. No. Dimension (in.)

Stl. or M.I. Alum. Size A B

122 122AL 1/2” 1-1/32 13/32

123 123AL* 3/4” 1-9/32 13/32

124 124AL 1” 1-19/32 1/2

125-TB 125AL 1-1/4” 1-15/16 9/16

126 126AL 1-1/2” 2-3/16 9/16

127 127AL 2” 2-11/16 19/32

128 128AL 2-1/2” 3-3/16 13/16

129 129AL 3” 3-27/32 13/16

130-TB 130AL 3-1/2” 4-7/16 15/16

131-TB 131AL 4” 4-7/8 1

132-TB — 4-1/2” 5-7/16 1-5/64

133-TB 133AL 5” 6-1/16 1-1/16

134-TB 134AL 6” 7-3/16 1-1/16

* Not U.L. Listed or CSA Certified

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Nylon insulated

metallic bushings

Steel or malleable iron (Steel thru 1-1/2 ”).

The Canadian Electric Code 10-906 (2) calls for

protection of ungrounded conductors by means

of smoothly rounded insulating surfaces at the

entrance to raceways, pull boxes, junction boxes,

etc. T&B insulated throat fittings, recognizable

by the distinctive trademarked blue insulating

liner in the throat, meet and surpass this Code

requirement. In addition, T&B insulated fittings

also reduce wire pulling effort by as much as

50%. Temperature rating 105°C.

Aluminum, steel or malleable iron

(steel thru 1-1/2”).

Smoothly rounded shoulder covers end of

conduit; broad flange covers knockout hole.

High ribs make tightening easy with fingers or

with wrench. 1/2”-1-1/2” sizes, formed in steel,

have extra smooth shoulders. Locknut-type

base gives improved bonding and resists

loosening under conditions of vibration.

CONFITMRO_EN_ALL.pdf 16 11/28/2011 11:05:20 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Plastic Insulating Bushings

Dimensions (in.)

Cat. No. Size A B

222-TB 1/2” 1-1/16 3/8

223-TB 3/4” 1-9/32 13/32

224 1” 1-37/64 9/16

225-TB 1-1/4” 2-1/32 9/16

226 1-1/2” 2-15/64 9/16

227 2” 2-25/32 5/8

228-TB 2-1/2” 3-13/32 3/4

229-TB 3” 4-3/32 3/4

230-TB 3-1/2” 4-5/8 7/8

231 4” 5-3/16 7/8

232 4-1/2” 5-5/8 7/8

233 5” 6-3/8 1

234 6” 7-7/16 1

Flame retardant. U.L. Rated 94V-1.

All Plastic Insulating Bushings

Impact-resistant plastic insulation. These

bushings have ribs for gripping when installing.

Perfect threads for easy thread on. U.L. Listed

105°C. NPT threaded.

CONFITMRO_EN_ALL.pdf 17 11/28/2011 11:05:20 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Insulating Bushing

(For Threadless Rigid Conduit and Intermediate Metal Conduit)

Insulated Metallic Bushing

Dimensions (in.)

Cat. No. Size A B C

TRIB-50 1/2” 19/32 1-9/32 1-1/16

TRIB-75 3/4” 25/32 1-25/64 1-1/4

TRIB-100 1” 1 1-1/2 1-9/16

TRIB-125 1-1/4” 1-5/16 1-5/8 1-59/64

TRIB-150 1-1/2” 1-17/32 1-21/32 2-11/64

TRIB-200 2” 1-31/32 1-13/16 2-11/16

TRIB-250 2-1/2” 2-23/64 2 3-1/4

TRIB-300 3” 2-59/64 2-7/32 3-29/32

TRIB-350 3-1/2” 3-3/8 2-5/16 4-29/64

TRIB-400 4” 3-27/32 2-13/32 5

I.M.C. sizes 1/2” thru 4”

U.L. Rated flame retardant 94V-1.

Application

• When assembled to the end of a

threadless conduit, provides a well

rounded insulating surface over

which conductors may be pulled

or on which conductors may bear

while in service.

Features

• Designed to be popped onto, and

bush, conduit end.

• Fast easy installation without screws.

• High impact thermoplastic

construction.

Standard Material

High impact thermoplastic listed for

105°C (221°F) application.

Flammability Classification 94V-1.

Standard Finish

As molded.

Range

1/2” through 4” conduit

Conformity

U.L. 514B

ANSI C80.4

NFPA 70-2008 (ANSI)

1. Cut conduit end squarely. Remove sharp edges

and burrs on inside and outside diameters by

reaming or filing.

2. Slip the pop-on bushing over the end of the

conduit.

3. Using the flat surface of any standard utility tool

such as an electricians pliers (or a hammer with

a block of wood, for the larger sizes), strike the

bushing on its top surface using a series of light

blows until the end of the conduit rests against

the bushing throat and conduit stop.

TRIB50 Series

CONFITMRO_EN_ALL.pdf 18 11/28/2011 11:05:20 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Knockout Bushings

Knockout Bushing

For use Wall

Trade in KO* Thickness

Cat. No. Size +.032/ -.016 A B of Elec. Box C D

3210 1/2” .875 1.000 .725 .095 MAX .360 .180

3211 3/4” 1.109 1.215 .940 .095 MAX .360 .180

3212 1” 1.375 1.500 1.200 .095 MAX .360 .180

3213 1-1/4” 1.734 1.865 1.550 .140 MAx .400 .210

3214 1-1/2” 1.984 2.240 1.760 .140 MAX .530 .310

3215 2” 2.469 2.740 2.245 .140 MAx .530 .310

* Per U.L. and NEMA standards.

Material: Thermoplastic

Flammability classification of 94V-1 Per UL 94

Service temperature: -40°C to 105°C.

3210 Series

Application

• To bush knockout openings in metal

boxes or enclosures.

Features

• One piece construction designed to

snap in place.

• High impact strength self-extinguishing,

non-dripping (per U.L. 94)

thermoplastic construction.

Standard Material

Thermoplastic rated for 105°C (221°F)

application.

Standard Finish

As molded.

Range

• .875” through 2.469” nominal diameter

knockout opening (1/2” through 2”

trade size knockouts).

• Wall thickness of box or enclosure

.095” max. up to 1” trade size.

.140” max. 1-1/4” through 2” trade size.

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NFPA 70-2008 (ANSI)

One-piece knockout bushing quickly snaps into

outlet box, switch box, or other enclosure left

vacant by wiring modifications or maintenance

changes. Provides smooth, rounded insulation

surface for easy wire pulling. Easily installed by

hand, they are available to fit 1/2” through 2”

knockouts. U.L. Listed 105°C. High impact

thermoplastic.

INSULINER®Sleeves

Dimension (in.)

Cat. No. Size A B

422 1/2” 5/8 .022

423 3/4” 11/16 .025

424 1” 7/8 .040

425 1-1/4” 1 .040

426-TB 1-1/2” 1 .050

427-TB 2” 1-1/8 .050

428-TB 2-1/2” 1-1/4 .035

429 3” 1-1/2 .035

430-TB 3-1/2” 1-25/32 .035

431 4” 2-1/32 .035

433 5” 2-1/2 .035

434 6” 2-1/2 .035

Oxygen index >28°

Slip over wires—insert

into bushing—snaps

into place

High dielectric nylon, 105°C.

An insuliner sleeve snapped into a regular

bushing makes a CSA Listed insulated bushing. For

standard rigid conduit, E.M.T. (thinwall conduit)

or any standard bushed outlet. Especially

suitable for use with flexible metallic conduit.

Converts ordinary bushing to code approved

insulated bushing without disturbing wiring.

19-e.pdf 1 2/21/2012 4:02:52 PM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Knockout Plugs

Dimensions (in.)

Cat. No. Size A B

1451 1/2” 1.060 .400

1452 3/4” 1.300 .400

1453 1” 1.590 .400

1454 1-1/4” 1.860 .450

1455 1-1/2” 2.240 .570

1456 2” 2.740 .570

Wall thickness of electrical box .095 max.

Meets Coast Guard Regulation CB293.

105°C rated by U.L. Made from flame

retardant, non-dripping thermoplastic.

A penny under a bushing will seal

the end of the conduit during

construction. Made to fit any

bushing. Completely salvageable.

Pennies—Steel

Cat. No. Size

815-TB 1/2”

816 3/4”

817 1”

818 1-1/4”

819 1-1/2”

820 2”

821 2-1/2”

822 3”

824 3-1/2”

823 4”

U.L. not applicable

Application

• To bush knockout openings in metal boxes or enclosures.

Features

• One piece construction designed to snap in place.

• High impact strength self extinguishing nondripping (per

U.L. 94) thermoplastic construction.

Standard Material

Thermoplastic rated for 105°C

(221°F) application.

Standard Finish

As molded.

Range

• .875” through 2.469” nominal diameter knockout opening

(1¼2” through 2” trade size knockouts).

• Wall thickness of box or enclosure

.095” max. up to 1” trade size.

.140” max. 1-1/4” through 2” trade size.

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NFPA 70-2008 (ANSI)

CONFITMRO_EN_ALL.pdf 20 11/28/2011 11:05:21 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Bushings and Push-Penny ®Plugs

Assembly consist of

Cat. No. Size A Bushing Push-penny

1460 1/2” 1-1/32” 122 1470-TB

1461 3/4” 1-9/32” 123 1471

1462 1” 1-19/32” 124 1472

1463 1-1/4” 1-15/16” 125 1473

1464 1-1/2” 2-3/16” 126 1474

1465* 2” 2-21/32” 127 1475

* Maleable Iron

Available in Aluminum

Add suffix AL to Cat. No.

Push-Penny ®Plugs

Cat. No. Size

1470-TB 1/2”

1471 3/4”

1472 1”

1473 1-1/4”

1474 1-1/2”

1475 2”

1476* 2-1/2”

1477* 3”

1478* 3-1/2”

1479* 4”

*Not CSA Certified.

CSA File No. 2884

UL not applicable.

Plug, Conduit, Connectors (Push-Penny®Plugs)

Application

• To plug open end of conduit or fitting in order to prevent

ingress of trash, dirt or moisture during construction and

remodeling.

Features

• Wide range of application; can be used with rigid metal

conduit, intermediate metal conduit, electrical metallic

tubing, all connnectors and all bushings.

• Designed to stand up to normal handling and is functionally

unaffected by moisture.

Standard Material

Polyethylene

Standard Finish

As molded.

Conformity

CSA C22.2 No. 18

ANSI C80.4

NFPA 70-2008 (ANSI)

NEMA FB-1

CEC Rule: 12-3024

“Unused openings in boxes, cabinets and fittings shall be

effectively closed by plugs or plates affording protection

substantially equivalent to that of the wall of the box, cabinet

or fittings.”

CONFITMRO_EN_ALL.pdf 21 11/28/2011 11:05:21 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

1942 Series

842AL Series (Non Insulated)

Application

• To effectively bush factory or

field-punched, cut, or drilled holes in

metal boxes or enclosures.

• To couple boxes back-to-back.

Features

• Rugged construction.

•Insulator curled over to: Bush

conductors entering/leaving at any

angle. Reduce wire pull effort.

Protect threads against damage

in handling.

Standard Material

1942 Series

Body

1/2”-Steel

3/8”, 3/4” through 6”-Malleable Iron

Insulator Nylon

842AL Series

All Copper-free Aluminum

(less than .4% copper)

Standard Finish

1942 Series Electro-zinc Plated

& Chromate Coated

842AL Series Degreased

Range 1942 & 842AL Series

1¼2” through 6”

All hub threads straight pipe (NPS).

Conformity

U.L. 514B

CSA C22.2 No. 18.3

Federal Specification W-F-408

ANSI C80.4

NFPA 70-2008 (ANSI)

NEMA FB-1

Federal Standard H-28 (Threads)

CHASE ®Nipple

NPS

Threads

Steel, malleable iron or aluminum.

CHASE ®Nipples

Cat. No. Dimensions (in.)

Stl. or M.I. Alum. Size A B

841TB — 3/8” 13/16 7/16

842TB 842ALTB†1/2” 15/16 11/32

843TB 843ALTB 3/4” 1-3/16 11/32

844 844AL†1” 1-7/16 21/32

845 845AL†1-1/4” 1-3/4 3/4

846 846AL 1-1/2” 2-1/16 13/16

847 847AL 2” 2-1/2 31/32

848 848AL 2-1/2” 3-1/16 1-1/16

849 849AL 3” 3-13/16 1-3/16

850 850AL 3-1/2” 4-3/8 1-5/16

851 851AL 4” 4-3/4 1-5/16

853 853AL 5” 5-7/8 1-5/16

854 854AL 6” 6-15/16 1-3/8

†Not U.L. Listed

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

CONFITMRO_EN_ALL.pdf 22 11/28/2011 11:05:21 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

CHASE®Nipples—Nylon Insulated

Size Dimensions (in.)

Cat. No. in. A B C

1942 1/2 15/16 1/2 19/32

1943 3/4 1-3/16 17/32 23/32

1944 1 1-7/16 21/32 7/8

1945 1-1/4 1-3/4 25/32 1-1/32

1946 1-1/2 2-1/16 13/16 1-3/32

1947 2 2-9/16 31/32 1-11/32

1948 2-1/2 3-1/16 1-1/16 1-7/16

1949 3 3-13/16 1-3/16 1-19/32

1950 3-1/2 4-3/8 1-5/16 1-25/32

1951 4 4-5/8 1-5/16 1-13/16

1953 5 5-29/32 1-5/16 1-13/16

1954 6 6-13/16 1-3/8 1-7/8

Steel or malleable iron

CONFITMRO_EN_ALL.pdf 23 11/28/2011 11:05:21 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

485 Series

370 Series

370AL Series

Application

• To connect threaded metal conduit

(ferrous rigid/nonferrous rigid/PVC

coated/or intermediate metal) to

a threadless opening in a box or

enclosure in outdoor or indoor

location exposed to continuous

or intermittent moisture.

• To positively bond conduit to box

or enclosure.

Features

• Rugged steel/malleable iron/copper-

free aluminum construction.

• Tapered internal threads for

watertight/dust tight union (A).

• Threads relieved to prevent

bottoming of conduit ensuring sound

assembly (B).

• Recessed sealing ring at box end.

Captive sealing ring (C).

• Hardened steel/malleable iron/

copper-free aluminum locknuts

designed to provide high quality

ground continuity; extended reach of

locknut permits clamping on thin

boxes and enclosures (D).

• Insulated throat protects conductors,

prevents abrasion and thinning of

conductor insulation, reduces wire

pull effort (E).

• Suitable for hazardous location use

per following:

(i) Class II, Division 1 Groups E, F, G,

CEC Rule 18-202

Class II, Division 2 Groups E, F, G,

CEC Rule 18-252

Class III, Division 1 Rule 18-302

Class III, Division 2 Rule 18-352

• PVC coated 485 Series

(i) Protects fitting from extremely

corrosive surroundings without

affecting integrity of electrical

grounding path (F).

(ii) Provided with overlapping sleeve

for additional seal (G).

Canadian Electric Code Rule 10-602

states that, “Where dissimilar metals

cannot be avoided at bonding

connections as indicated in Rule 2-112

(2). Connections shall be made using

methods or material that will minimize

deterioration from galvanic action”.

Joint Industrial Council (JIC) Electrical

Standards also forbid dissimilar metals

in contact for the same reason and

require that the fittings for metal conduit

be of malleable iron or ductile iron and

have impact strength comparable to

that of the conduit.

“Copper-free Aluminum”

• Copper-free aluminum castings

for fittings have a maximum of 0.4%

copper. The most detrimental effect of

higher percentage of copper on

aluminum base alloy is its decrease in

corrosion resistance.

Threaded Hubs (Bullet®Hubs)

(For Threaded Rigid Metal Conduit/IMC/PVC Coated Rigid Metal Conduit)

(B)

(C)

(E)

(A)

Predetermined

Compression

(B)

(C)

(E)

(D)

(G)

(F)

(A)

(G)

(D)

CONFITMRO_EN_ALL.pdf 24 11/28/2011 11:05:21 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Threaded Hubs (Bullet®Hubs)—continued

(For Threaded Rigid Metal Conduit/IMC/PVC Coated Rigid Metal Conduit)

Standard Material

370-485 Series 370AL

Body 1/2” thru 1” Steel All Copper-Free Aluminum

1-1/4” thru 6” Malleable Iron

Locknut 1/2” thru 2” Steel (hardened) 1/2” thru 2” Steel (hardened)

2-1/2” thru 6” Malleable Iron 2-1/2” thru 4” Copper-free

Aluminum

Screws Steel (hardened)

‘O’ Ring Buna N

Insulator Nylon

Coating PVC

Standard Finish

370 Series 370AL Series 485 Series

Hub Electro-zinc Plated As Cast PVC—Outside.

Chromate Coated. Electro-zinc

Locknuts All Ferrous locknuts Plated Chromate

Electro-Zinc Plated Coated Inside.

and Chromate Coated.

Screws All Electro-Zinc Plated

& Chromate Coated.

Range

370 Series 1/2” thru 6” Conduit

370AL & 485 Series 1/2” thru 4” Conduit

All hub threads—straight pipe

All female threads—taper pipe

(NPT)

Conformity

U.L. 514B

CSA 22.2 No. 18.3

ANSI C80.4

NFPA 70-2008 (ANSI)

NEMA FB-1

JIC EGP1; JIC EMP 1

Federal Specification W-F-408

Federal Standard H-28 (Threads)

CONFITMRO_EN_ALL.pdf 25 11/28/2011 11:05:21 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Steel/Malleable Iron and Aluminum Hub Fittings†

Cat. No. Size Dimensions (in.) Wall Thk.

Stl. or M.I. Alum.** A B C (max.)in.

370 370AL 1/2 1-3/8 1-5/16 3/4 5/16

371 371AL 3/4 1-5/8 1-3/8 7/8 5/16

372 372AL 1 2-3/32 1-23/32 1-7/32 5/16

373 373AL 1-1/4 2-9/16 2 1-11/32 5/16

374 374AL 1-1/2 3-3/32 2 1-11/32 5/16

375 375AL 2 3-5/8 1-31/32 1-11/32 5/16

376 — 2-1/2 4-1/8 2-21/32 1-15/16 5/16

377 — 3 5 2-31/32 2 1/2

378 — 3-1/2 5-9/16 3-1/8 2-1/8 1/2

379-TB — 4 6-9/16 3-1/8 2-1/8 1/2

381-TB — 5 8 4 2-3/16 1/2

382-TB — 6 9-3/16 4 2-3/16 1/2

** Aluminum not available with insulated throat.

†U.L. Listed raintight and CSA Certified watertight and dust tight.

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Bullet®Hub Fittings with Bonding Locknut —

Nylon Insulated

Cat. No. Size (in.) Description

401 1/2

402 3/4

403-TB 1 Available in steel or malleable iron

404-TB 1-1/4 (steel through 1 inch.).

405-TB 1-1/2 Used with a neoprene “O” ring to provide

407 2-1/2 Supplied with 106 series bonding nut.

408 3Tem perature rating: 105° C.

409 3-1/2

410-TB 4

CSA certified watertight and dust tight.

Nylon insulated.

Aluminum, steel, or malleable iron (steel

through 1”). With Neoprene “O” Ring provides a

watertight threaded hub on enclosures. U.L.

Listed 105°C.

CONFITMRO_EN_ALL.pdf 26 11/28/2011 11:05:22 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

PVC Coated Hub for Rigid Conduit

Dimensions (in.)

Cat. No. Conduit Size A B C

485 1/2” 1-21/64 2-1/8 1-7/8

486 3/4” 1-19/32 2-3/8 2-1/8

487 1” 1-27/32 2-3/4 2-3/8

488 1-1/4” 2-15/32 3-3/8 3-1/8

489 1-1/2” 2-29/32 3-5/8 3-1/2

490 2” 3-3/8 3-3/4 4

491 2-1/2” 3-27/32 4 4-1/2

492 3” 4-21/32 4-5/8 5-3/8

493 3-1/2” 5-9/64 4-13/16 5-7/8

494 4” 5-3/4 4-9/16 6-7/16

*485 Series are CSA Certified Watertight and Dustight for Ordinary Locations.

Spacing Chart for Bullet ®Hubs

Center to Center Spacing Min. Space from

Conduit Sizes Center of KO

Bullet®Hub to Diameters

1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 3-1/2 4 Wall of Box (min.)

1/2 1-7/16 1-5/8 1-3/4 2-1/8 2-3/8 2-5/8 2-7/8 3-5/16 3-1/2 3-7/8 3/4 7/8

3/4 — 1-3/4 1-7/8 2-1/4 2-1/2 2-3/4 3 3-1/2 3-3/4 4-1/8 7/8 1-1/8

1— — 2 2-3/8 2-5/8 2-7/8 3-1/8 3-5/8 3-7/8 4-1/4 1-1/8 1-3/8

1-1/4 — — — 2-11/16 2-15/16 3-1/4 3-1/2 4 4-1/4 4-1/2 1-3/8 1-3/4

1-1/2 — — — — 3-1/8 3-1/2 3-3/4 4-1/8 4-3/8 4-3/4 1-5/8 2

2— — — — — 3-3/4 4 4-1/2 4-3/4 5 1-7/8 2-1/2

2-1/2 — — — — — — 4-1/4 4-3/4 5 5-3/8 2-1/8 3

3— — — — — — — 5-1/8 5-3/8 5-3/4 2-5/8 3-5/8

3-1/2 — — — — — — — — 5-5/8 6 2-7/8 4-1/8

4— — — — — — — — — 6-1/4 3-1/4 4-5/8

Steel or malleable iron (steel thru 1-1/4”).

T&B Hub Centerline Spacing Chart

Conduit

Trade Size 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3” 3-1/2” 4” 5” 6”

inc.

1/2”1-9/16

3/4”1-43/64 1-25/32

1”1-27/32 1-61/64 2-1/8

1-1/4”2-1/32 2-9/64 2-5/16 2-1/2

1-1/2”2-7/32 2-21/64 2-1/2 2-11/16 2-7/8

2”2-15/32 2-37/64 2-3/4 2-15/16 3-1/8 3-3/8

2-1/2”2-23/32 2-53/64 3 3-3/16 3-3/8 3-5/8 3-7/8

3”3-1/32 3-9/64 3-5/16 3-1/2 3-11/16 3-15/16 4-3/16 4-1/2

3-1/2”3-11/32 3-21/64 3-5/8 3-13/16 4 4-1/4 4-1/2 4-13/16 5-1/8

4”3-19/32 3} 3-7/8 4-1/16 4-1/4 4-1/2 4-3/4 5-1/16 5-3/8 5-5/8

5”4-9/32 3-25/64 4-9/16 4-3/4 4-15/16 5-3/16 5-7/16 5-3/4 6-1/16 6-5/16 7

6”4-11/16 4-51/64 4-31/32 5-5/32 5-11/32 5-19/32 5-27/32 6-5/32 6-15/32 6-23/32 7-13/32 7-13/16

Nearest obstruction to center of hub.

27/32 61/64 1-1/8 1-5/16 1-1/2 1-3/4 2 2-5/16 2-5/8 2-7/8 2-9/16 3-31/32

PLASTIC

COATING

LOCKNUT

NFS THREAD

INSULATOR

SEALING RING

CONFITMRO_EN_ALL.pdf 27 11/28/2011 11:05:22 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

THE T&B Hub

Never before has a single hub fit like this one. Designed for unequalled performance. The innovative engineering of the

T&B Hub will, quite simply, raise your performance expectations for threaded hubs. The revolution in hub design is here,

and the fate of our competition is sealed.

Figure 1 Figure 2 Figure 3

1. Sealing ring and groove with

innovative profile outperforms

standard 'O' ring design. Sealing

ring is captive before installation

and resists buckling or slipping during

installation. The seal groove is

designed for op ti mum compression of

the sealing ring. The sealing ring is

designed to provide a complete 360°

seal, even when the conduit is not

perpendicular with the enclosure. (See

Figure 1)

2. Locknut design with pe riph er al

slots and a hexagonal/angled

spline spaced every 30° enables

easy application of torque with

wrench or hammer and screw driv er.

(See Figures 2 & 3)

3. Sharper and deeper teeth on

locknut and body designed for a

more penetrating bite for improved

bonding to the enclosure.

4. Hexagonal / splined body design

for fast, easy installation with

wrench or hammer and screwdriver.

5. Precision machined tapered

threads designed to create water-

tight union.

6. Insulated throat molded from

105°C rated thermoplastic with a

flammability rating of 94 V-O.

T&B Hub

Trade Max. Panel Throat

Cat. Size Dia. Thickness Dia.

No. (in.) A B C D E

H050-TB 1/2 1-7/16 1-9/16 7/8 3/16 19/32

H075-TB 3/4 1-21/32 1-19/32 29/32 3/16 25/32

H100-TB 1 2 1-13/16 1-1/16 1/4 1

H125-TB 1-1/4 2-3/8 1-7/8 1-1/16 1/4 1-5/16

H150-TB 1-1/2 2-3/4 1-7/8 1-1/16 1/4 1-17/32

H200-TB 2 3-1/4 1-15/16 1-5/32 1/4 1-31/32

H250-TB 2-1/2 3-3/4 2-9/16 1-9/16 1/4 2-13/32

H300-TB 3 4-3/8 2-21/32 1-19/32 1/4 2-31/32

H350-TB 3-1/2 5 2-23/32 1-5/8 1/4 3-13/32

H400-TB 4 5-1/2 2-23/32 1-5/8 1/4 3-7/8

H500-TB 5 6-7/8 3-1/32 1-15/16 1/4 4-15/16

H600-TB 6 7-11/16 3-5/32 2 1/4 6

Material – Hub and Locknut: zinc or copper free aluminum

Insulating Throat: thermoplastic temp. rating – 105°C, Flammability Rating: – 94V-0

Sealing Ring Nitrile (BUNA “N”)

For Aluminum Hubs add suffix A(i.e. H050A). For Chrome Plated Hubs add suffix CP (i.e. H050CP).

Meets NEMA sealing requirements for NEMA 3R, 4 & 13 enclosures.

U.L. Listed and CSA Certified. CSA Certified use in hazardous locations Class I, Division 2, Class II,

Divisions 1 and 2, Groups E, F and G, Class III, Division 1, 2 and Type 4.

Chrome Plated Hubs (suffix-“CP”) are rated NEMA 4X.

Throat Dia. E

28-29-e.pdf 1 12/28/2012 1:24:58 PM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

T&B Grounding Hub

Dimensions (in.)

AB CDE

Trade Max. Panel Throat

Cat. No. Size Dia. Thickness Dia.

H050GR-C 1/2 17/16 19/16 7/8 3/16 19/32

H075GR-C 3/4 12-1/32 1-19/32 29/32 3/16 25/32

H100GR-C 1 2 1-13/16 1-1/16 1/4 1

H125GR-C 1-1/4 2-3/8 1-7/8 1-1/16 1/4 1-5/16

H150GR-C 1-1/2 2-3/4 1-7/8 1-1/16 1/4 1-17/32

H200GR-C 2 3-1/4 1-15/16 1-15/32 1/4 1-31/32

H250GR-C 2-1/2 3-3/4 2-9/16 1-9/16 1/4 2-13/32

H300GR-C 3 4-3/8 2-21/32 1-19/32 1/4 2-31/32

H350GR-C 3-1/2 5 2-23/32 1-5/8 1/4 3-13/32

H400GR-C 4 5-1/2 2-23/32 1-5/8 1/4 3-7/8

H500GR-C 5 6-7/8 3-1/32 1-15/16 1/4 4-15/16

H600GR-C 6 7-11/16 3-5/32 2 5/16 6

Material—Hub and Locknut: zinc or copper-free aluminum.

Insulating Throat: thermoplastic temp. rating—105°C;

flammability rating:—94V-0.

Sealing Ring: Nitrile (BUNA “N”)

For Aluminum Grounding Hubs add suffix A(i.e. H050GRA-C).

For Chrome Plated Hubs add suffix CP (i.e. H050GRCP).

For 316 Stainless Steel Hubs add suffix SST (i.e. H050GRSST).

For PVC coating add suffix PVC (i.e. H050GRPVC-C).

Meets NEMA sealing requirements for NEMA 3R, 4 & 13 enclosures.

U.L. Listed and CSA Certified.

CSA approved for use in hazardous locations: Class I, Division 2, Class II, Divisions 1 & 2,

Groups E, F & G, Class III, Division 1, 2 and Type 4.

T&B Grounding and Bonding Locknut

Max.

Trade A B Ground Conductor

Cat. No. Size Dia. Height Screw Size

L050GR-C 1/2 1-1/2 13/32 #10-32 x 1/4” #10

L075GR-C 3/4 1-11/16 13/32 #10-32 x 1/4” #10

L100GR-C 1 2 13/32 #10-32 x 1/4” #10

L125GR-C 1-1/4 2-3/8 15/32 1¼4-20 x 1/4” #10

L150GR-C 1-1/2 2-3/4 15/32 1¼4-20 x 5/16” #8

L200GR-C 2 3-1/4 15/32 1¼4-20 x 5/16” #8

L250GR-C 2-1/2 3-3/4 11/16 1¼4-20 x 5/16” #6

L300GR-C 3 4-3/8 23/32 1¼4-20 x 5/16” #6

L350GR-C 3-1/2 5 23/32 1¼4-20 x 5/16” #6

L400GR-C 4 5-1/2 23/32 1¼4-20 x 5/16” #4

L500GR-C 5 6-5/8 23/32 3¼8-16 x 3/8” #2

L600GR-C 6 7-11/16 23/32 3¼8-16 x 3/8” #1

Material—Locknut: zinc or copper-free aluminum

For Aluminum Locknuts add suffix A. (i.e. L050GRA-C)

For Chrome Plated Locknuts add suffix CP. (i.e. L050GR-CP)

For 316 Stainless Steel Locknuts add suffix SST (i.e. L050GRSST).

Grounding Locknut for Hubs

Throat Dia.

28-29-e.pdf 2 12/28/2012 1:24:59 PM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

T&B Bulkhead Fittings

Bulkhead Fitting

Trade

Cat. No. Size

H050BHD 1/2”

H075BHD 3/4”

H100BHD 1”

H125BHD 1-1/4”

H150BHD 1-1/2”

H200BHD 2”

H250BHD 2-1/2”

H300BHD 3”

H350BHD 3-1/2

H400BHD 4”

H500BHD 5”

H600BHD 6”

Thru Bulkhead Fitting

Trade

Cat. No. Size

H050TBF 1/2”

H075TBF 3/4”

H100TBF 1”

H125TBF 1-1/4”

H150TBF 1-1/2”

H200TBF 2”

Thru Bulkhead Hub

Trade

Cat. No. Size

H050TBH 1/2”

H075TBH 3/4”

H100TBH 1”

H125TBH 1-1/4”

H150TBH 1-1/2”

H200TBH 2”

Trade Across

Size Thread Height Diameter Flats A B

1/2” 1/2”-14 1-13/32 1-7/16 1 3/4 1/2

3/4” 3/4”-14 1-15/32 1-11/16 1-1/4 25/32 17/32

1” 1”-11-1/2 1-11/16 2 1-17/32 29/32 19/32

1/4” 1-1/4”-11-1/2 1-25/32 2-3/8 1-27/32 29/32 21/32

1-1/2” 1-1/2”-11-1/2 1-13/16 2-3/4 1-1/8 29/32 21/32

2” 2”-1-1/2 1-27/32 3-1/4 2-5/8 15/16 21/32

2-1/2” 2-1/2”-8 29/32 3-3/4 3-1/8 17/32 7/8

3” 3”-8 2-9/16 4-3/8 3-25/32 15/16 29/32

3-1/2” 3-1/2”-8 2-9/16 5 4-9/32 1-3/8 7/8

4” 4”-8 2-9/16 5-1/2 4-27/32 1-3/8 7/8

5” 5”-8 2-23/32 6-5/8 5-29/32 1-15/32 7/8

6” 6”-8 3 7-11/16 7-1/32 1-1/2 31/32

Material—Hub, Body and Locknut: zinc or copper-free aluminum

Insulating Throat: thermoplastic temp. rating—105°C; Flammability rating:—94V-0

Sealing Ring: Nitrile (BUNA “N”)

For Aluminum Bulkhead add suffix A.

For Chrome Plated Bulkhead add suffix CP.

Nipple Nut

Not Included

Across Flats

Height

Diameter

Thread

CONFITMRO_EN_ALL.pdf 30 11/28/2011 11:05:23 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Offset Reducers

Trade Dimensions (in.)

Cat. No. Size Height Dia. (Ø) A B C D E

H150-075ORGR-TB 1-1/2”-3/4” 1-21/32 2-3/4 15/16 23/32 1-29/32 1-9/32 11/32

H150-100ORGR-TB 1-1/2”-1” 1-25/32 2-3/4 1-1/16 23/32 1-29/32 1-9/16 7/32

H150-125ORGR-TB 1-1/2”-1-1/4” 1-25/32 2-3/4 1-1/16 23/32 1-29/32 1-7/8 1/32

H250-200ORGR-TB 2-1/2”-2” 2-1/8 3-3/4 1-3/16 15/16 2-29/32 2-21/32 3/32

Material—Offset Reducer and Locknut: zinc or copper-free aluminum

Insulating Throat: thermoplastic temp. rating—105°C; Flammability rating—94V-0

Sealing Ring: Nitrile (BUNA “N”)

For Aluminum Offset Reducer add suffix A. (i.e. H150-125ORGRA-TB)

For Chrome Plated Offset Reducer add suffix CP. (i.e. H150-125ORGRCP-TB)

Capoffs

Trade Dimensions (in.)

Cat. No. Size Height Diameter A B C

H050CAP 1/2” 1-13/32 1-7/16 19/32 27/32 3/16

H075CAP 3/4” 1-15/32 1-11/16 19/32 1-1/16 3/16

H100CAP 1” 1-11/16 2 11/16 1-5/16 1/4

H125CAP 1-1/4” 1-25/32 2-3/8 23/32 1-21/32 1/4

H150CAP 1-1/2” 1-13/16 2-3/4 23/32 1-29/32 1/4

H200CAP 2” 1-27/32 3-1/4 23/32 2-3/8 1/4

H250CAP 2-1/2” 2-9/32 3-3/4 7/8 2-29/32 1/4

H300CAP 3” 2-9/16 4-3/8 7/8 3-1/32 11/32

H350CAP 3-1/2” 2-9/16 5 29/32 4-1/32 11/32

H400CAP 4” 2-9/16 5-1/2 29/32 4-1/2 11/32

H500CAP 5” 2-23/32 6-5/8 29/32 5-9/16 11/32

H600CAP 6” 3 7-5/8 31/32 6-5/8 11/32

Material—Capoff and Locknut: zinc or copper-free aluminum

Insulating Throat: thermoplastic temp. rating—105°C; flammability rating—94V-0

Sealing Ring: Nitrile (BUNA “N”)

For Aluminum Capoff add suffix A. (i.e. H050CAPA)

For Chrome Plated Capoff add suffix CP. (i.e. H050CAPCP)

Dia. (Ø)

Height

Capoff

Height

Dia. (0)

Dia.

CONFITMRO_EN_ALL.pdf 31 11/28/2011 11:05:23 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Threadless Fittings/Couplings

(For Threadless Rigid Metal Conduit and Intermediate Metal Conduit)

Application

• To connect and effectively bond

threadless rigid metal

conduit/intermediate metal conduit to

a box or enclosure, or to couple ends

of threadless conduit.

Features

• Steel/Malleable Iron Construction.

• Case hardened ring bites into

conduit for high quality continuity and

grip.

• Nylon insulator firmly secured in place

protects conductors and reduces

wire pulling effort by as much as

50%; prevents thread damage in

handling.

• Case hardened steel locknut or

malleable iron locknut designed

to provide a positive bond.

• Suitable for concrete tight application.

• Raintight application.

• Capable of carrying ground fault

currents up to 10,000 amps RMS

(1/2" through 1-1/2” size) and 20,000

amps RMS (2” and above sizes)

duration of current 3 cycles.

Standard Material

Nut, Gland 1/2” to 1” Steel—1-1/4”

to 4” Malleable Iron

Body All Malleable Iron

Ring Steel (case hardened)

Insulator Nylon

Locknut 1/2” thru 2” Steel

(hardened) 2” thru 4”

Malleable Iron

Standard Finish

Electro Zinc Plated & Chromate

Coated

Range

• 8123 & 8120 Series 1/2” through 4”

Size Conduit

• 8130 Series 1/2” and 3/4”

Size Conduit

• All hub threads Straight Pipe

(NPS)

Conformity

U.L. 514B

CSA C22.2 No. 18.3

ANSI C80.4

NFPA 70-2008 (ANSI)

NEMA FB-1

Federal Specification W-F-408

Federal Standard H-28 (Threads)

8123 Series

8130 Series

8120 Series

CONFITMRO_EN_ALL.pdf 32 11/28/2011 11:05:23 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Nylon Insulated Threadless Fittings

Cat. No. Conduit Dimensions (in.)

Nylon Insul. Non-Insul. Size A B C

8123 8121 1/2” 1-11/32 1-15/16 3/4

8223 8221 3/4” 1-5/8 2 3/4

8323 8321 1” 1-7/8 2-7/16 7/8

8423 8421 1-1/4” 2-3/8 2-9/16 11/16

8523 8521 1-1/2” 2-5/8 2-3/4 3/4

8623 8621 2” 3-1/4 2-15/16 27/32

8723-TB 8721 2-1/2” 3-15/16 3-15/16 1-1/8

8823-TB 8821 3” 4-11/16 4-1/8 1-7/32

8853 8851 3-1/2” 5-3/16 4-1/4 1-1/8

8973 8971 4” 5-11/16 5 1-1/8

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Threadless Couplings

Dimensions (in.)

Cat. No. Size A B

8120 1/2” 1-9/32 2

8220 3/4” 1-19/32 2-5/16

8320 1” 1-7/8 2-11/16

8420 1-1/4” 2-3/8 2-13/16

8520 1-1/2” 2-5/8 3-5/8

8620 2” 3-1/4 3-13/16

8720 2-1/2” 3-15/16 5-3/8

8820 3” 4-11/16 5-1/2

8850 3-1/2” 5-3/16 5-1/2

8970 4” 5-11/16 5-1/2

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

A split steel ring with diagonal serrations grips the

conduit and bites into it for positive ground.

Makes a permanent connection and eliminates

the need for cutting a thread on the conduit.

Insulation helps to guarantee continuity of

service with protection of the conductor at the

critical point—the fitting bushing. Malleable iron

construction.

Eliminate conduit threading. When tightened

with a wrench they make a U.L. Listed and CSA

Certified concrete-tight connection.

Malleable iron.

CONFITMRO_EN_ALL.pdf 33 11/28/2011 11:05:23 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Threadless Short Elbows—Nylon Insulated

Dimensions (in.)

Cat. No. Size A B C

8130 1/2” 1-11/32 1-1/2 1/2

8131 3/4” 1-5/8 1-3/4 9/16

8132 1” 1-7/8 1-15/16 11/16

8134 1-1/2” 2-23/32 3-1/8 13/16

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Ideal for entering enclosure or conduit body at right

angles. Eliminates need to thread conduit. As with

straight couplings, this fitting makes a concrete-

tight connection. Malleable iron.

CONFITMRO_EN_ALL.pdf 34 11/28/2011 11:05:23 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Specifications — Set Screw Fitting/Coupling

(For Threadless Rigid Metal Conduit and Intermediate Metal Conduit)

Application

• To connect and effectively bond threadless rigid metal conduit or intermediate

metal conduit to a box or enclosure or to couple ends of threadless conduit.

Features

• Thickwall steel or malleable iron body.

• Hardened hex head cup point screw to provide high quality bond.

• Captive screw, will not vibrate loose.

• Nylon insulated throat meets and exceeds all codes requirements for bushing:

(i) Prevents thinning of insulation.

(ii) Reduces installation effort.

(iii) Prevents first thread damage.

• Coupling provided with positive center stop.

• Suitable for concretetight application.

• Capable of carrying ground fault currents up to 10,000 amps RMS

(1¼2 through 1-1/2” size) and 20,000 amps RMS (2” and above sizes).

Standard Material

Body 1/2” thru 2” Steel

2-1/2” thru 4” Malleable Iron

Locknut 1/2” thru 2” Steel (hardened)

2-1/2” thru 4” Malleable Iron

Screw Steel (hardened)

Insulator Nylon

Standard Finish

Electro Zinc Plated & Chromate Coated.

Conformity

U.L. 514B

CSA C22.2 No. 18.3

ANSI C80.4

NFPA 70-2008 (ANSI)

NEMA FB-1

Federal Specification W-F-408

Federal Standard H-28 (Threads)

8125 Series

8124 Series

CONFITMRO_EN_ALL.pdf 35 11/28/2011 11:05:23 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Insulated Set-Screw Fitting

Conduit Dimensions (in.)

Cat. No. Size A B

8125 1/2” 1-3/8 13/32

8225 3/4” 1-1/2 7/16

8325 1” 1-13/16 35/65

8425 1-1/4” 2 5/8

8525-TB 1-1/2” 2-5/16 5/8

8625 2” 2-7/16 11/16

8725-TB 2-1/2” 3-3/8 1

8825 3” 3-7/16 1

8855 3-1/2 3-7/8 1-1/16

8975 4” 4-3/16 1-1/8

Sizes 1/2”-2” made of steel. Sizes 2-1/2”-4” are malleable iron.

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Set Screw Coupling

Conduit Dimensions (in.)

Cat. No. Size A

8124 1/2” 2-1/2

8224-TB 3/4” 2-11/16

8324-TB 1” 2-27/32

8424 1-1/4” 3

8524 1-1/2” 3-3/8

8624 2” 3-5/8

8724-TB 2-1/2” 3-7/8

8824-TB 3” 4-1/4

8854 3-1/2 4-15/16

8974 4” 5-3/8

Sizes 1/2”-2” made of steel; sizes 2-1/2”-4” are malleable iron.

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Eliminate conduit threading with these set

screw fittings. Captive hex head screws tighten

down onto conduit for positive holding strength

and ground. The fittings are furnished with

insulated throats reducing wire pulling effort by

as much as 50%. Approved concrete-tight.

Eliminate the need for threading conduit ends

when joining rigid conduit with these set screw

couplings. Captive hex head screws provide

positive holding strength and ground continuity.

Approved concrete-tight.

CONFITMRO_EN_ALL.pdf 36 11/28/2011 11:05:23 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Bushed Elbows

Dimensions (in.)

Cat. No. Size A B C

460TB 1/2” 1-13/16 1-1/8 5/8

461TB 3/4” 2-1/4 1-1/2 9/16

462 1” 2-23/32 1-23/32 11/16

463 1-1/4” 3-1/8 2-1/16 25/32

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Short Elbows—Nylon Insulated

Dimensions (in.)

Cat. No. Size A B C

4290 1/2” 1-7/32 1-1/4 1/2

4291 3/4” 1-7/16 1-5/16 9/16

4292 1” 1-23/32 1-9/16 11/16

4293 1-1/4” 2-7/32 2-1/16 13/16

4294 1-1/2” 2-15/32 2-3/16 13/16

4295 2” 3 2-9/16 13/16

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Not U.L. Listed

Short Elbows

Dimensions (in.)

Cat. No. Size A B C

4250 1/2” 1-5/16 1-1/4 7/16

4251 3/4” 1-17/32 1-5/16 1/2

4252 1” 1-13/16 1-9/16 5/8

4253 1-1/4” 2-9/32 2-1/16 11/16

4254 1-1/2” 2-9/16 2-3/16 11/16

4255 2” 3-3/32 2-9/16 11/16

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

The noninsulated elbow has smoothly rounded

shoulders to protect conductor insulation.

Malleable iron.

The integral insulation of the insulated elbow is

a guarantee that the bushing of every fitting will

be smooth. Malleable iron.

When an insulated elbow is not desired, the

Noninsulated short elbow should be used.

Malleable iron.

CONFITMRO_EN_ALL.pdf 37 11/28/2011 11:05:24 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Application

• To couple and effectively bond

threaded ends of rigid metal conduit/

intermediate metal conduit where

neither length of conduit can be

rotated.

Features

• Malleable Iron/Steel/Copper-free

Aluminum Construction.

• Free fitting threads ensure easy

assembly.

• Permits conduit coupling without

rotating either conduit.

• Provides rigid in-line coupling with

high quality grounding; will not loosen

under vibration.

• Suitable for concrete-tight application.

• Capable of carrying ground fault

currents up to 10,000 amps RMS

(1/2” through 1-1/2” size) and up to

20,000 amps RMS (2” and above)

(duration of fault current 3 cycles)

(674 series tested).

Standard Material

674 Series

Bushing and Body Malleable Iron

Ring Steel up to 2” or

Malleable Iron

675AL Series

Bushing and Body Aluminum

Ring Aluminum

Standard Finish

674 Series: Electro Zinc Plated &

Chromate Coated

675AL Series: Degreased

Range

• 674 Series: 3/8” thru 6” Conduit

• 675AL Series: 1/2” thru 6” Conduit

• All straight pipe threads (NPS)

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NEMA FB1

ANSI C80.4

NFPA 70-2008 (ANSI)

Federal Specification W-F-408

Federal Standard H-28 (Threads)

Threaded Coupling (ERICKSON®Couplings)

(For Threaded Rigid Metal Conduit and Intermediate Metal Conduit)

674 Series

675AL Series

ERICKSON®Couplings

Cat. No. Dimensions (in.)

Mal. Iron Alum.* Size A B

674 — 3/8” 1-1/8 1-1/8

675 675AL 1/2” 1-15/32 1-1/4

676 676AL 3/4” 1-9/16 1-13/32

677 677AL 1” 1-29/32 1-5/8

678 678AL 1-1/4” 2-3/8 1-13/16

679 679AL 1-1/2” 2-5/8 1-31/32

680-TB 680AL 2” 3-7/32 2-7/32

681 681AL 2-1/2” 3-3/32 2-11/16

682 682AL 3” 4-7/16 2-29/32

683 683AL 3-1/2” 5 3

684 684AL 4” 5-1/2 3-3/16

685 685AL†4-1/2” 6-1/4 3-15/32

686 686AL 5” 6-25/32 3-3/4

687 687AL 6” 8 4-1/32

* Copper-free Aluminum (less than .4% Copper).

U.L. Listed and CSA Certified concrete-tight.

†Not CSA Certified.

With an Erickson coupling, a conduit run may be

completed when neither conduit can be turned.

A conduit run may also be broken without taking

down the whole run. Conduit joined with

Erickson Couplings is rigid and in line and

vibration will not loosen the connections.

CONFITMRO_EN_ALL.pdf 38 11/28/2011 11:05:24 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Panel Fitting Extensions

Dimensions (in.)

Cat. No. Size A B C

1440 1/2” 1-1/4 1-3/16 1-7/8

1441 3/4” 1-1/4 1-13/32 1-15/16

1442 1” 1-3/16 1-21/32 1-15/16

1443 1-1/4” 1-1/4 2-1/8 2

Male Enlargers*

Dimensions (in.)

Cat. No. Size A B C

1245 1/2” to 3/4” 1-1/4 1-5/32 1/2

1246 3/4” to 1” 1-17/32 1-9/32 15/32

1244 1” to 1-1/4” 1-7/8 1-7/16 17/32

1247 1-1/4” to 1-1/2” 2-3/16 1-15/32 19/32

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Female Reducers*

Dimensions (in.)

Cat. No. Size A B C

1250-TB 3/4” to 1/2” 1-1/8 5/8 3/16

1261 1” to 1/2” 1-7/16 1-7/16 3/16

1251 1” to 3/4” 1-3/8 11/16 3/16

1262 1-1/4” to 1/2” 1-13/16 21/32 3/16

1263 1-1/4” to 3/4” 1-13/16 23/32 3/16

1252 1-1/4” to 1” 1-3/4 25/32 7/32

1253 1-1/2” to 1-1/4” 2 13/16 1/4

1254 2” to 1-1/2” 2-3/8 1-3/16 9/32

1255 2-1/2” to 2” 3 1-1/4 3/8

1256 3” to 2-1/2” 3-5/8 1-1/2 1/2

1257 3-1/2” to 3” 4-1/8 1-9/16 1/2

1258 4” to 3-1/2” 4-5/8 1-3/16 1/2

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

Ideal when longer thread length is needed. Will

combine with any fitting having a male thread.

Male thread of panel fitting extension is 1” long.

Malleable iron.

Adapt an outlet hole to the next larger size of

conduit. Rough ends of conduit carefully covered

by built-in bushing. Malleable iron.

Adapt any outlet to the next smaller size of

conduit. Hex shoulder makes wrench tightening

convenient. Malleable iron.

CONFITMRO_EN_ALL.pdf 39 11/28/2011 11:05:24 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Threaded Reducers

Cat. No. Dimensions (in.)

Stl. or M.I. Alum. Size A

600-TB 600AL-TB 1/2” to 3/8” 5/8

601-TB 601AL-TB 3/4” to 1/2” 19/32

602-TB 602AL-TB 1” to 1/2” 19/32

603-TB 603AL-TB 1” to 3/4” 19/32

604-TB 604AL-TB 1-1/4” to 1/2” 19/32

605-TB 605AL 1-1/4” to 3/4” 19/32

606-TB 606AL 1-1/4” to 1” 11/16

607 607AL 1-1/2” to 1/2” 15/16

608 608AL 1-1/2” to 3/4” 15/16

609 609AL 1-1/2” to 1” 1-3/32

610 610AL 1-1/2” to 1-1/4” 27/32

611-TB 611AL 2” to 1/2” 23/32

612 612AL 2” to 3/4” 1-1/16

613 613AL 2” to 1” 1-1/16

614-TB 614AL 2” to 1-1/4” 1-1/16

615-TB 615AL 2” to 1-1/2” 27/32

Reducing Washers

Dimensions (in.)

Cat. No. Size A B

3700 3/4” to 3/8” 1-3/8 45/64

3701 3/4” to 1/2” 1-3/8 7/8

3702 1” to 3/8” 1-5/8 45/64

3703 1” to 1/2” 1-5/8 7/8

3704 1” to 3/4” 1-5/8 1-3/32

3705-TB 1-1/4” to 3/8” 2 45/64

3706 1-1/4” to 1/2” 2 7/8

3707 1-1/4” to 3/4” 2 1-3/32

3708 1-1/4” to 1” 2 1-23/64

3709 1-1/2” to 3/8” 2-1/4 45/64

3710 1-1/2” to 1/2” 2-1/4 7/8

3711 1-1/2” to 3/4” 2-1/4 1-3/32

3712 1-1/2” to 1” 2-1/4 1-23/64

3713 1-1/2” to 1-1/4” 2-1/4 1-23/32

3714 2” to 1/2” 2-3/4 7/8

3715-TB 2” to 3/4” 2-3/4 1-3/32

3716 2” to 1” 2-3/4 1-23/64

3717 2” to 1-1/4” 2-3/4 1-23/32

3718 2” to 1-1/2” 2-3/4 1-31/32

For reducing the threaded opening in conduit

bodies or any female threaded fitting. Smooth,

built-in bushing completely covers rough ends

of conduit. Iron or steel construction. Steel from

600-TB thru 606-TB, also 614 & 615.

Washers reduce knockout hole in outlet box.

Newly designed of galvanized steel. These

washers, used in pairs, interlock and form a rib

which centers the washers and conduit in the

knockout.

CONFITMRO_EN_ALL.pdf 40 11/28/2011 11:05:24 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Application

• To support and securely fasten rigid

metal conduit and intermediate metal

to the supporting surface.

Features

• Rugged malleable iron/copper-free

aluminum construction—snugly fits

on the conduit.

• Designed to prevent accumulation of

moisture and start of corrosion on

vertical run of conduit (A).

Standard Material

1275 Series

Malleable Iron

1976AL Series

All copper-free

aluminum

Standard Finish

1275 Series

Hot Dipped Galvanized

1276AL Series

As Cast

Range

•1275 Series

3/8” through 6” conduit

•1276AL Series

1/2” through 6” conduit

Conformity

CSA C22.2 No. 18.3

ANSI C80.4

NFPA 70-2008 (ANSI)

Conduit

Strap

Conduit

Spacer

Supporting

Wall

1275 Series

1276AL Series

Designed to fit each size of conduit snugly. High

reinforcing ribs on each side increase strength,

reduce weight. Hot-dipped galvanized finish.

Conduit Straps

(For Rigid Metal Conduit and Intermediate Metal Conduit)

Pipe Straps—Malleable Iron or Aluminum

Cat. No. Dimensions (in.) Screw

Mal. Iron Alum. Size A B C Size

1275†1275AL 3/8” 1-15/16” 19/32” 1/4” 1/4”

1276†1276AL†1/2” 2-11/32” 23/32” 1/2” 1/4”

1277†1277AL†3/4” 2-11/16” 21/32” 5/8” 1/4”

1278†1278AL†1” 3-3/32” 11/16” 13/16” 1/4”

1279†1279AL†1-1/4” 4-1/8” 13/16” 29/32” 5/16”

1280†1280AL 1-1/2” 4-1/2” 15/16” 1-17/32” 3/8”

1281 1281AL 2” 5-3/16” 1-1/8” 1-1/4” 7/16”

1282* 1282AL 2-1/2” 5 -15/16” 1-1/2” 1-3/4” 1/2”

1283* 1283AL 3” 6-11/16” 1-5/8” 2-3/16” 1/2”

1284 1284AL 3-1/2” 7-19/32” 1-3/4” 2-3/4” 5/8”

1285* 1285AL 4” 8-5/16” 1-7/8” 2-13/16” 5/8”

1286** 1286AL** 4-1/2” 9-3/16” 1-15/16” 2-15/16” 5/8”

1287 1287AL 5” 9-15/16” 2” 3-1/4” 5/8”

1288 1288AL 6” 11-1/2” 2-7/16” 4-1/8” 5/8”

* May be used with EMT of same size.

†Not snap on type.

U.L. not applicable.

** Not CSA Certified

CONFITMRO_EN_ALL.pdf 41 11/28/2011 11:05:24 AM

Pipe Straps—Steel

Conduit Dimensions (in.) Screw

Cat. No. Size A B C Size

1210C†3/8” 1-15/32 3/4 11/16 1/4”

1211C 1/2” 2 3/4 15/16 1/4”

1212C 3/4” 2-5/16 3/4 1” 1/4”

1213C 1” 3-13/16 3/4 1-17/64 1/4”

1214TB* 1-1/4” 2-31/32 1-9/16 1-9/16 3/8”

1215TB* 1-1/2” 3-23/32 1-13/16 1-13/16 3/8”

1216TB* 2” 4-7/16 2-5/16 2-5/16 3/8”

†Not snap on type.

U.L. not applicable.

* Not CSA Certified.

Corrosion Resistant PVC Coated Rigid Conduit Straps

Bolt Dimensions (in.)

Cat. No. Size Size A B C

1275CR 3/8” 1/4” 2 21/32 1/4

1276CR 1/2” 1/4” 2-13/32 25/32 1/2

1277CR 3/4” 1/4” 2-3/4 23/32 5/8

1278CR 1” 1/4” 3-5/32 3/4 13/16

1279CR 1-1/4” 3/8” 4-5/32 25/32 7/8

1280CR 1-1/2” 3/8” 4-9/16 1 1-7/32

1281CR 2” 1/2” 5-1/4 1-3/16 1-1/4

U.L. not applicable.

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Elongated bolt hole makes alignment easy, even

when holes in mounting surface are off center.

Snap on features. Steel. Zinc plated

Malleable iron. Designed to fit each size of

conduit snugly. High reinforcing ribs on each

side increase strength, reduce weight.

CONFITMRO_EN_ALL.pdf 42 11/28/2011 11:05:24 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Application

• Provides mounting surface for

conduit where installation requires

air space between conduit and

supporting surface.

Features

• Prevents conduit rusting from wall

condensation.

• Spacers can be stacked one atop

the other facilitating installation and

eliminating expensive conduit off

setting (A).

• Designed to cover wide range;

marked with accurate size marking

for proper positioning (B).

Standard Material

1350 Series

Malleable Iron

1350AL Series

Copper-free aluminum

Standard Finish

1350 Series

Hot Dipped Galvanized

1350AL Series

As Cast

Range

1/2” through 6” conduit

Conformity

CSA C22.2 No. 18.3

ANSI C80.4

NFPA 70-2008 (ANSI)

1350 Series

1350AL Series

Conduit Spacers

(For Rigid Metal Conduit, Intermediate Metal Conduit and Electrical Metallic Tubing)

CONFITMRO_EN_ALL.pdf 43 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Pipe Spacers

Cat. No. Screw Dimensions (in.)

Mal. Iron Alum. Size Size A B

1350 1350AL 3/8”, 1/2”, 3/4”, 1” #7 3” 7/8”

1351 1351AL 1-1/4”-1-1/2”-2” #12 5” 1-3/16”

1352 1352AL 2-1/2”-3” #12 9-9/16” 1-3/4”

1353 1353AL 3-1/2”-4” #14 7-9/16” 2”

1354 1354AL 4-1/2”-5”-6” #16 10-9/16” 2-9/16”

Conforms to CEC Rule 12-012 (5)

U.L. not applicable.

Pipe Spacers—PVC Coated

Conduit Screw Dimensions (in.)

Cat. No. Size Size A B

1350CR 1/2”-3/4”-1” #7 3 7/8

1351CR 114”-1-1/2”-2” #12 5 3/8

1352CR 2-1/2”-3” #12 6-9/16 1-3/4

1353CR 3-1/2”-4” #14 7-9/16 2

1354CR 4-1/2”-5”-6” #16 10-9/16 2-9/16

U.L. not applicable.

Conforms to CEC Rule 12-012 (5)

Used with T&B conduit straps to permit space

between conduit and mounting surface.

Eliminates need for costly offset-bending

conduit and possible corrosive moisture traps

when conduit is mounted directly to a surface.

Hot-dipped galvanized finish, premountable and

stackable to eliminate offsetting.

Corrosion resistant PVC coated malleable iron.

Pre-mountable, stackable to eliminate offsetting.

Spacers can be stacked for offsets on wall or

into outlet box. Prevents conduit rusting from

wall condensation. Eliminates offsetting of

conduit.

CONFITMRO_EN_ALL.pdf 44 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Tite-Bite®Combination Couplings

Armoured Cable for Threaded Rigid

Dimensions (in.)

Cat. No. Size A B

440-C 1/2” 1-5/8 1-27/32

441 3/4” 1-3/4 2-1/8

442 1” 2 2-17/32

Beam Clamps Adjustable

Cat. No. Description

700TB Fits Flange 2-3/4”-7-3/8”

703* Special Bolt and 3 Nuts

* Not CSA Certified

Conduit Supports

Cat. No. Size

690TB 1/2”

691TB 3/4”

692TB 1”

693TB 1-1/4”

Includes bolts. Steel.

These supports will fit any flange, tapered or

straight up to 5/8” thick. The broad hook holds the

conduit at any desired angle. Holds standard rigid

conduit, E.M.T., or I.M.C. Malleable iron.

A one-piece fitting that couples armoured cable or

flexible conduit to threaded rigid conduit. Tite-Bite

wedge holds conduit securely with a double grip.

With a Chase®nipple, this fitting will connect

flexible conduit to outlet boxes, allowing more

wiring space in the box than the usual fitting.

Malleable iron.

CONFITMRO_EN_ALL.pdf 45 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Methods of Bonding and Grounding

CONCRETE

TIGHT

CONCRETE

TIGHT

RAIN

TIGHT

Case 1: Where threaded or threadless

conduit terminates into a threadless

opening in a sheet metal box or enclosure

with or without concentric or eccentric

knockouts.

(1) Threaded or threadless rigid metal

conduit or intermediate metal conduit

(2) T&B Series 8123 or 8124

Threadless Fittings

(3) T&B Series 8125 Set Screw Fitting

(4) T&B Series 370 or H050-TB

Sealing Hub (Bullet®Hubs)

(5) T&B Series 140 Locknuts

(6) T&B Series 106 Bonding Locknut

(7) T&B Series 3870 Bonding

& Grounding Bushing

(8) T&B Sta-Kon®or Color-Keyed®lug

Bonding jumper around concentric or eccentric

rings required by CEC Rule 10-614

Threadless opening in a sheet metal box or

enclosure.

Method of Bonding

For 120/208 volts or 120/240 volts circuits

provided no unpunched rings remain around the

knockout.

For under or over 250 volts circuits, service

equipment and hazardous locations (where

applicable) provided no unpunched rings remain

around the knockout.

For under or over 250 volts circuits, service

equipment and hazardous locations (where

applicable) with or without unpunched rings

around the knockout.

CONFITMRO_EN_ALL.pdf 46 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Case 2: Where threaded or threadless

conduit terminates into a threaded hub in a

cast metal enclosure.

Methods of Bonding

For (1) 120/208 or 120/240 volts

circuits (CEC 10-610)

(2) Over 250 volts circuits

(CEC 10-610)

(3) Service equipment

(CEC 10-604)

(4) Hazardous Locations 18-074

(where applicable)

18-124 (Class I, Zone 1)

18-160 (Class I, Zone 2)

18-218 (Class II, Division 1)

18-268 (Class II, Division 2)

18-316 (Class III, Division 1)

18-366 (Class III, Division 2)

(1) Threaded or threadless rigid

metal conduit or intermediate metal

conduit.

(2) T&B Series 8123 Threadless Fitting

(3) T&B Series 8125 Set Screw Fitting

Methods of Bonding and Grounding (continued)

CONCRETE

TIGHT

CONCRETE

TIGHT

RAIN

TIGHT

Threaded hub in a cast

metal enclosure

CONFITMRO_EN_ALL.pdf 47 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Methods of Bonding and Grounding (continued)

Threadless opening

in a sheet metal

box or enclosure

Case 3: Where threaded conduit

terminates into a threadless opening in a

sheet metal box or enclosure with no

concentric or eccentric rings remaining

around knockout.

Method of bonding for 120/208 volt or 120/240

volts circuits (other than service equipment).

Method of bonding for over 250 volts circuits

e.g. 600/347 volt systems and those operating

over 600 volts (other than service equipment).

Note: Any of the bonding methods described for service equipment may also be used.

CONFITMRO_EN_ALL.pdf 48 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Case 3:

(cont’d) Where threaded conduit

terminates into a threadless opening in

a sheet metal box or enclosure with no

concentric or eccentric rings remaining

around knockout.

(1) Threaded rigid metal conduit or

intermediate metal conduit

(2) T&B Series 142 Locknuts

(3) T&B Series 122 Bushing Metallic

(4) T&B Series 222 Bushing Plastic

(5) T&B Series 106 Bonding Locknut

(6) T&B Series 3650 Bonding Wedge

Method of Bonding

For (i) Over 250-volts circuit e.g.

347/600-volts systems and

those operating over 600 volts

(ii) Service equipment

(iii) Hazardous locations where

applicable

Methods of Bonding and Grounding (continued)

CONFITMRO_EN_ALL.pdf 49 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Case 4: Where threaded conduit

terminates into a threadless opening in

a sheet metal box or enclosure with

concentric or eccentric rings remaining

around knockout.

Methods of bonding for under or over

250-volts, for service equipment and for

hazardous locations where applicable.

Note: Bonding jumper required by CEC

Rule 10-614

(1) Threaded rigid metal conduit or

intermediate metal conduit

(2) T&B Series 142 Locknuts

(3) T&B Series 122 Bushing, Metallic

(4) T&B Series 3650 Bonding Wedge

(5) T&B Series 3870 Bonding &

Grounding Bushing

(6) T&B Typical Mechanical or Pressure

Type Fitting

Note: For raintight applications, a sealing

ring, T&B Series 5302, may be used

between outside of box or enclosure and

the outside locknut.

Methods of Bonding and Grounding (continued)

CONFITMRO_EN_ALL.pdf 50 11/28/2011 11:05:25 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Methods of Bonding and Grounding (continued) —

Typical Installation Using Bonding and Grounding Bushings

Bonding Service Equipment

(CEC Rule 10-604)

Install Bonding Jumper to Assure Electrical Continuity

Between Isolated Sections of Raceways (CEC Rule 10-614)

Multiple Bonding of Service Raceways Where

Service Entrance Conductors are Paralleled in

Two or More Raceways, CEC Rule 10-614

1 T&B Series 142 Locknut

2 T&B Series 3870 Bonding & Grounding Bushing

(Threaded)

3 T&B Series 5262 Sealing “O” Ring

4 T&B Typical Bolted or Pressure Lug

Suggested Specifications

Insulated grounding and bonding bushing (Series 3870)

Where code requires bonding and grounding of single or

multiple metal conduits, or positive bonding and grounding of

metal conduit to the box, enclosure or auxiliary gutter, the end

of the conduit shall be equipped with an insulated metallic

grounding and bonding bushing such as Series 3870

manufactured by Thomas & Betts.

Grounding and bonding bushings used shall be approved for

the purpose and

(i) Shall be of malleable iron/steel/aluminum construction

adequately protected against corrosion.

(ii) Bushing insulator shall be listed or certified for

150°C/302°F application with a flammability rating of

94V-O. Insulator must be positively locked in place.

SERVICE CONDUITS

GROUND BUS

BUS BAR

SERVICE

ENCLOSURE

(i) Installing bonding jumper around unpunched concentric

or eccentric knockouts in sheet metal box or enclosure

[CEC Rule 10-806].

(ii) Installing bonding jumper in hazardous locations where

‘locknut bushing’ or ‘double locknut’ type of contact is

unacceptable method for bonding purposes

[CEC Rule 18-074]

Bonding required by CEC Rule 10-606

Bonding jumper required by

CEC Rule 10-606

CEC Rule 10-806

Bonding Method per CEC Rule 10-806

Bonding required by CEC Rule 10-604

Bonding Method per CEC Rule 10-806

LOAD SIDE

OF SERVICE

EQUIPMENT

CONFITMRO_EN_ALL.pdf 51 11/28/2011 11:05:26 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Methods of Bonding and Grounding (continued) —

Typical Installation Using Thomas &Betts Bonding locknut

(1) T&B Series 142 Locknut

(2) T&B Series 106 Bonding Locknuts

(3) T&B Series 122 Bushing

Suitable for Bonding Raceway, EMT

or Terminating Fitting to a sheet

metal box or enclosure where

(a) No unpunched concentric or

eccentric rings remain around the

knockout.

(b) Ordinary locknut is unacceptable

for bonding purposes such as

(i) Service Equipment

Enclosures CEC Rule 10-614

(ii) Bonding for circuits over

250 volts (where required)

CEC Rule 10-614

(iii) Bonding in Hazardous

Locations regardless

of the voltage of the system

CEC Rule 18-074

Suggested Specifications

Bonding Type Locknut (Series 106)

Where drawings indicate installation of a

bonding type locknut to effectively bond

a terminating fitting or metal conduit to a

cabinet, box, enclosure or an auxiliary

gutter, the locknuts installed shall be of

hardened steel/malleable iron

construction, electro-zinc plated, such

as Series 106 manufactured by Thomas

& Betts.

CONFITMRO_EN_ALL.pdf 52 11/28/2011 11:05:26 AM

T&B Conduit Fittings

Rigid and Intermediate Metal Conduit Fittings

Methods of Bonding and Grounding (continued) —

Typical Installations Using Thomas & Betts Bonding and Grounding Wedge

T&B Series 3651

Bonding & Grounding Wedge

(1) T&B Series 142 Locknut

(2) T&B Series 122 Metallic Bushing

(3) T&B Series 3651 Bonding &

Grounding Wedge

(4)T&B Pressure (crimp type)

Terminal Lug.

Grounding electrode

Conductor enclosure

(Rigid Metal Conduit or

Intermediate Metal Conduit)

Service Enclosure

Service Equipment

Bonding Jumper

Equipment Bonding Jumper

Phase Conductors

Grounding electrode

conductor

Threaded Rigid Metal Conduit

or intermediate Rigid Metal Conduit

Sheet Metal Box or

Enclosure with unpunched

concentric or eccentric

rings remaining around

knockout opening.

Ground Bus

Acceptable Method for Bonding

Following

(i) Service Equipment

CEC Rule 10-614

(ii) Bonding for Circuits over 250 volts

CEC Rule 10-614

(iii) Bonding in Hazardous Locations

CEC Rule 18-074

When installed with a bonding jumper,

acceptable method of bonding where

unpunched rings remain around

concentric or eccentric knockouts in

sheet metal boxes or enclosures.

[CEC Rule 10-614].

Suggested Specifications

Bonding and Grounding Wedge

(Series 3650)

Bonding and Grounding Wedges

installed to effectively bond terminating

fitting or metal conduit to a cabinet, box,

enclosure or an auxiliary gutter or to

install bonding jumper around

concentric or eccentric knockouts shall

be of the type as manufactured by

Thomas & Betts—Series 3650.

Bonding and Grounding Wedge

shall be of rugged bronze/tin plated or

steel/electro-zinc plated.

CONFITMRO_EN_ALL.pdf 53 11/28/2011 11:05:26 AM

T&B Conduit Fittings

Electrical Metallic Tubing (EMT) Fittings

Specifications — Electrical Metallic Tubing (EMT)

Ref. CEC Rule 12-1400 not exceeding

750 Volts

Electrical Metallic Tubing (EMT) is similar to

rigid steel conduit but is much lighter,

weighing approximately 40 percent as

much as rigid steel conduit of the same

nominal size. EMT can be used for both

exposed or concealed work provided that,

during installation or afterwards, it is not

subjected to severe physical damage. Use

of EMT is restricted to systems not

exceeding 600 volts and to non-

hazardous locations except for Class II

Division 2, acceptable in Class III

Division 1 and Division 2 per CEC Rule

18-302 (1).

Galvanized Steel EMT installed in

concrete, on grade or above, generally

requires no supplementary corrosion

protection. However, when installed

in concrete below grade level and in

contact with soil or cinders,

supplementary corrosion protection

consisting of a protective coating of

bitumastic or asphalt base paint or plastic

is generally applied. EMT run in or under

permanently moist cinder fill must be

encased in at least two inches of cinder-

free concrete unless the conduit is at least

18 inches below the fill.

Aluminum EMT cannot be directly

embedded in concrete containing

soluble chlorides such as calcium

chloride, unwashed beach sand, sea

water or coral bearing aggregates.

When adequately treated with a

protective coating of bitumastic or asphalt

base paint or plastic coating, the

raceway can be installed in concrete

containing chlorides.

In wet locations where walls are

frequently washed or where there are

surfaces of absorbent material, the entire

wiring system, including boxes, fittings,

conduits and cables, must be supported

such that there is at least 1/4 inch air

space between it and the supporting

surface.

Fittings and couplings are required to

be of concrete tight type when

embedded in masonry or concrete or in

dry locations and of the raintight type

when installed in wet locations (CEC

Rule 12-1410).

Where No. 4 or larger underground

conductors enter or leave a conduit, an

insulating bushing with a smooth

well-rounded insulating surface must be

provided to protect conductors unless the

terminating fitting is equipped with an

insulated throat, firmly secured in place

providing equivalent protection. The

insulating bushing or insulating material

must have a temperature rating of not less

than the insulation temperature rating of

installed conductors.

CEC Rule 12-3022 requires that

the raceways be metallically joined

together into a continuous electric

conductor and must be mechanically

connected to all boxes, fittings and

cabinets as to provide effective

electrical continuity.

EMT is not permitted to be threaded.

Cut ends of tubing are required to be

reamed. Code requires that EMT be

adequately supported and restricts bends

in one run to the equivalent of four quarters

or 360 degrees total.

Portions of this section reprinted by

permission from the Canadian Electrical

Code 2009 Part I.

For further details and complete

information please refer to the following:

1. NEC Article 358…Electrical Metallic

Tubing

2. ANSI C80.3…Electrical Metallic

Tubing, Zinc Coated

3. U.L.797…Standards for Safety,

Electrical Metallic Tubing

4. ANSI C80.4…Fittings for Rigid

Metal Conduit and Electrical

Metallic Tubing

5. U.L. 514, Standards for Safety,

Outlet Boxes and Fittings

6. WW-C-563…Conduit, Metal, Rigid,

and Bend and Elbow, Electrical

Conduit, Thinwall Type (EMT)

7. W-F-408…Fittings for Conduit,

Metal, Rigid, (Thickwall & Thinwall

(EMT) Type)

8. NEMA FB-1…Standards

Publication, Fittings and Supports

for Conduit & Cable Assemblies

9. CEC Section 12-1400…Electrical

Metallic Tubing

10.CSA C22.2 No. 83…Safety

Standards for Electrical

Metallic Tubing

11.CSA C22.2 No. 18…Safety

Standards for Outlet Boxes,

Conduit Boxes and Fittings

Please Note

The excerpts and other material herein, whether relating to the Canadian

Electrical Code 2002 Part I, the Underwriters Laboratories, Inc. listing, to

industry practice or otherwise, is not intended to provide all relevant

information required for use and installation. Reference to original or primary

source material and data is mandatory before any application or use is made of

the product.

CONFITMRO_EN_ALL.pdf 54 11/28/2011 11:05:26 AM

T&B Conduit Fittings

Electrical Metallic Tubing (EMT) Fittings

Suggested Specifications for Electrical Metallic Tubing (EMT)

Fittings

Series 5123 Insulated

EMT Fitting (Raintight)

(Compression Type)

Series 5120

EMT Coupling (Raintight)

(Compression Type)

Series 1350 Pipe Spacers

Series 106

Bonding Locknut

Series 4176

Pipe Straps

• Ferrous Electrical Metallic Tubing (EMT)

shall be of the hot dipped

galvanized type conforming to

applicable specifications WW-563/ANSI

C80.3/U.L. 797/CSA C22.2 No. 83.

EMT protected solely by enamel shall

not be used.

• Where lengths of EMT are coupled

together or connected to boxes or

enclosures or where EMT is coupled to

threaded rigid metal conduit or IMC,

fittings approved for intended

applications shall be used, and:

(1) Shall be of rugged steel/malleable

iron construction electro-zinc

plated inside/outside including

threads. Fitting throat shall be

bushed with a nylon insulator.

(2) Shall be of raintight type for

installations exposed to weather or

wet locations such as Thomas &

Betts series 5123, 5120 and 530.

Raintight type fittings may be substituted

for concrete tight application.

• Where electrical metallic tubing and

associated fittings are used as part

of equipment grounding system:

(1) A bonding type locknut such

as Thomas & Betts series 106

shall be installed where hub

type fitting terminates into a

threadless opening

(2) Compression ring type fittings

such as Thomas & Betts series

5123 and 5120 shall be used

for terminating and coupling.

• EMT shall be securely fastened in place

at intervals as specified by the code

using straps, hangers and other

supporting assemblies as indicated on

plans, and as manufactured by Thomas

& Betts, series 4176 straps. In wet

locations or where supporting surfaces

are of absorbent materials vertical and

horizontal runs of conduit shall be firmly

supported such that there is at least

1/4” air space between conduit and

supporting surface

• Spacers and supporting straps shall be

of rugged malleable iron or steel

construction, hot dipped galvanized,

and conforming to requirements of

Canadian Standards Association

Standard C22.2 No. 18.3 as

manufactured by Thomas & Betts,

series 4176 straps and series 1350

spacers.

CONFITMRO_EN_ALL.pdf 55 11/28/2011 11:05:26 AM

T&B Conduit Fittings

Electrical Metallic Tubing (EMT) Fittings

Specifications — Fittings for Electrical

Metallic Tubing (EMT) Compression Type, Raintight

Application

• To connect and effectively bond

electrical metallic tubing to a box

or an enclosure.

• To provide a raintight connection

between tubing and the fitting.

• To couple ends of tubing.

Features

• Rugged all steel construction.

• Rings designed to positively bond

conduit to fitting; unique locknut

design provides effective bond

between fitting and box or enclosure;

ground continuity is assured.

• Nylon insulator firmly secured in

place—protects conductors, reduces

wire pulling effort and prevents thread

damage in handling.

• Locknuts are designed with extended

reach to lock fitting on to a thin box

or an enclosure.

• Locknuts tighten without deformation;

will not vibrate loose.

Standard Material

All Steel except Insulator.

Insulator Thermoplastic, U.L.

Rated 105°C

Standard Finish

All Steel Parts Electro Zinc Plated

& Chromate Coated

Insulator As Molded

Range

• Conduit Size 1/2” thru 2”

• Hub Size 1/2” thru 2” NPS

Hubs provided with straight pipe

threads NPS.

Conformity

U.L. 514B

CSA 22.2 No. 18.3

NFPA 70-2008 (ANSI)

NEMA FB-1

Federal Specification W-F-408

Federal Standard H-28 (Threads)

5123 Series*

* 4230 Series—90° Fittings

5120 Series

CONFITMRO_EN_ALL.pdf 56 11/28/2011 11:05:27 AM

T&B Conduit Fittings

EMT Fittings

EMT Fittings—Nylon Insulated

Dimensions (in.)

Cat. No. Size A B

5123 1/2” 1-3/64 1-21/32

5223 3/4” 1-21/64 1-27/32

5323 1” 1-11/16 1-7/8

5423 1-1/4” 2-1/16 2-11/32

5523 1-1/2” 2-5/16 2-23/32

5623 2” 2-25/32 2-13/16

U.L. Listed and CSA Certified raintight.

EMT Couplings

Dimensions (in.)

Cat. No. Size A B

5120 1/2” 1-1/16 1-27/32

5220 3/4” 1-5/16 2-1/8

5320 1” 1-11/16 2-1/8

5420 1-1/4” 2-1/16 2-29/32

5520 1-1/2” 2-5/16 3-1/16

5620 2” 2-3/4 3-7/32

U.L. Listed and CSA Certified raintight.

EMT Fittings

Dimensions (in.)

Cat. No. Size A B

5121-TB 1/2” 1-1/16 1-9/16

5221 3/4” 1-5/16 1-21/32

5321 1” 1-11/16 1-3/4

5421 1-1/4” 2-1/16 1-11/32

5521-TB 1-1/2” 2-5/16 2-9/16

5621 2” 2-3/4 2-3/4

U.L. Listed and CSA Certified raintight.

T&B E.M.T. (thinwall) fittings comply with Federal Spec. WF408B.

Across

Corners

Across

Corners

CONFITMRO_EN_ALL.pdf 57 11/28/2011 11:05:27 AM

T&B Conduit Fittings

EMT Fittings

Short Elbows—Insulated

Dimension (in.)

Cat. No. Size A B C

4240 1/2” 1-7/8 1-1/8 11/16

4241-TB 1/2” 1-11/16 1-3/8 1/2

4242 1” 1-7/8 1-5/8 5/8

4243-TB 1-1/4” 2-3/4 2-5/16 11/16

4244 1-1/2” 3-1/16 2-5/8 11/16

4245 2” 3-3/8 3-7/32 3/4

U.L. Listed and CSA Certified raintight.

Short Elbows Malleable Iron

Dimension (in.)

Cat. No. Size A B C

4230 1/2” 1-7/16 1-9/32 7/16

4231 3/4” 1-11/16 1-19/32 1/2

4232 1” 1-7/8 1-27/32 5/8

4233 1-1/4” 2-3/4 2-15/32 11/16

4234 1-1/2” 3-1/16 2-3/4 11/16

4235 2” 3-3/8 3-5/16 11/16

U.L. Listed and CSA Certified raintight.

Combination Coupling—Steel

Dimension (in.)

Cat. No. Size A B

530-TB 1/2” 1-3/8 1-1/16

531 3/4” 1-1/2 1-11/32

532 1” 1-19/32 1-21/32

U.L. Listed and CSA Certified raintight.

Ideal for cramped locations or tight corners

where large radius conduit elbows will not fit or

would appear unworkmanlike. Shoulders on

body of 1/2” size are hex-shaped to provide

positive holding for standard installation

tools. Use insulated type for simple, and safe,

installations. Malleable iron. CSA rated 105°C.

Ideal for cramped locations or tight corners

where large radius conduit elbows will not fit or

would appear unworkmanlike. Shoulders on

body of 1/2” size are hex-shaped to provide

positive holding for standard installation tools.

For connecting EMT to threaded rigid and

intermediate metal conduit.

Across

Corners

CONFITMRO_EN_ALL.pdf 58 11/28/2011 11:05:27 AM

T&B Conduit Fittings

EMT Fittings

Pipe Straps—Steel

Dimensions (in.)

Cat. No. Size A B C (Bolt Hole)

4159C 1/2” 1-27/32 3/4 1/4

4160C 3/4” 2-1/32 3/4 1/4

4161C 1” 2-11/32 3/4 1/4

4162* 1-1/4” 2-7/8 3/4 1/4

4163* 1-1/2” 3-11/16 1-1/4 11/32

4164* 2” 4-1/16 1-1/8 13/32

Not U.L. Listed

*Not CSA

Conform to CEC 12-1404

Pipe Straps—Malleable Iron

Dimensions (in.)

Cat. No. Size A B C (Bolt Hole)

4176 1/2” 2-5/32 2-1/32 1/4

4177 3/4” 2-9/16 1-1/16 1/4

4178 1” 3 3/4 1/4

4179 1-1/4” 3-3/4 1-3/16 5/16

4180 1-1/2” 4-3/16 1-5/16 3/8

4181 2” 5-3/16 1-1/8 7/16

1282* 2-1/2” 5-15/16 1-1/2 1/2

1283* 3 6-11/16 1-5/8 1/2

1284* 3-1/2 7-19/32 1-3/4 5/8

1285* 4” 8-5/16 1-7/8 5/8

Not U.L. Listed.

*Not CSA

Conforms to CEC 12-1404

Pipe Spacers

Dimensions (in.)

Cat. No. Size A B

1350 1/2”, 3/4”, 1” 3” 7/8”

1351 1-1/4”,1-1/2”, 2” 5” 1-3/16”

1352 2-1/2”, 3” 9-9/16” 1-3/4”

1353 3-1/2”, 4” 7-9/16” 2”

1354 4-1/2”, 5”, 6” 10-9/16” 2-9/16”

Conforms to CEC 12-012 (5).

Oval Hole for Screw Size (C)

Elongated bolt hole makes alignment easy, even

when holes in mounting surface are out of

alignment. Snap on features hold strap in place.

Oval Hole for Screw Size (C)

Designed to fit each size of conduit snugly. High

reinforcing ribs on each side increase strength,

reduce weight. Hot dipped galvanized finish.

Used with T&B conduit straps to permit space

between conduit and mounting surface. Eliminates

need for costly offset-bending conduit and possible

corrosive moisture traps when conduit is mounted

directly to a surface. Malleable iron. Hot-dipped

galvanized finish, pre-mountable and stackable to

eliminate offsetting.

CONFITMRO_EN_ALL.pdf 59 11/28/2011 11:05:27 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Hard Junior Hard Vacuum

Service Cord Service Cord Cleaner Cord

1. Use Extra Hard Hard Light

Pendant, Portable Pendant, Portable Pendant, Portable

2. Voltage Rating Up to 600 volts Up to 300 volts Up to 300 volts

3. Conductor Material Copper (Stranded) Copper (Stranded) Copper (Stranded)

4. Type Designation

(Depends on Jacket Material)

i. Rubber Jacket Type S Type SJ Type SV

ii. Oil Resistant Rubber Jacket Type SO Type SJO Type SVO

iii. Thermoplastic Jacket Type ST Type SJT Type SVT

iv. Oil Resistant

Thermoplastic Jacket Type STO Type SJTO Type SVTO

Please Note

The excerpts and other material herein, whether relating to the Canadian Electrical

Code 2009 Part I, the Underwriters Laboratories, Inc. listing, to industry practice or

otherwise, is not intended to provide all relevant information required for use and

installation. Reference to original or primary source material and data is mandatory

before any application or use is made of the product.

Specifications — Flexible Cord and Cables

Ref. CEC Section 4 (Conductors)

The Canadian Electrical Code,

Flexible

Cords

are known by their trade names

“Hard Service Cord,” “Junior Hard Service

Cord” and “Vacuum Cleaner Cord.”

Depending on jacket material, flexible

cords listed are suitable for use where

immersed in water or where occasionally

or continuously in contact with oil or

immersed in oil, or outdoors and in mobil-

homes and recreational vehicles.

Flexible cord is permitted by Code for

use in portable appliances or stationary

equipment requiring movement for service

and repair and for wiring in cranes, hoists

and elevators. Flexible cord is also

permitted to be used to prevent

transmission of noise or vibration.

Flexible cord is not permitted as a

substitute for fixed wiring of structures or

where concealed behind building walls,

ceilings or floors. Running flexible cord

through holes in walls, ceilings, floors or

through doorways, windows or similar

openings is also prohibited.

CEC Section 4 requires that flexible

cords be so connected to devices and

to fittings that tension is not transmitted

to joints or terminal screws. Use of

suitable strain relief fittings designed for

the purpose is one of the

recommended alternatives.

Please refer to the following for further

details and complete information:

1. U.L. 62, ANSI C33.1…Safety

Standard for Flexible Cord and

Fixture Wire

2. U.L. 514B, Safety Standard for

Outlet Boxes and Fittings

3. CEC Section 4…Conductors

4.010…Uses of Flexible Cord

4.038…Uses of Portable Power Cable

12-010 (4)…Flexible Cords in Ducts

and Plenum Chambers

22-108 (2)…Bonding conductor for

Flexible Cords for Portable Equipment

44-350 (1) (b)…Flexible Cords for

Portable Stage Equipment

50-016…Flexible Cord for Attachment

Plugs and Similar Wiring Devices

70-108…Power Supply Cord-Factory-

Built Relocatable Structures and Non-

relocatable Structures

76-002…Temporary Wiring

76-010…Feeders

78-058 (2)…Marinas and Yacht

Clubs

78-104 (2)…Marine Wharves,

Structures, and Fishing Harbourgs

4. CSA C22.2 No. 49…Safety

Standards for Flexible Cords and

Cables and Fixture Wires

5. CSA C22.2 No. 18…Safety

Standards for Outlet Boxes, Conduit

Boxes and Fittings

Following is a brief description of

the three cords.

CONFITMRO_EN_ALL.pdf 60 11/28/2011 11:05:27 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Suggested Specifications for Flexible Cord and Cable Fittings

• Flexible cord or cable and

associated fittings shall be suitable

for conditions of use and location

and approved for the purpose by

a nationally recognized testing

laboratory, inspection agency or

product evaluation organization.

• Flexible cord or cable shall be so

connected to the device or fitting that

tension will not be transmitted to

joints or terminal screws. Sufficient

slack shall be provided to avoid

sharp flexing and straining. Cord or

cable shall be installed in such a

manner that liquid will tend to run off

the surface instead of draining

towards the fitting.

• Where flexible cord or cable exposed

to intermittent or constant moisture

and subjected to mechanical strain is

terminated into a threaded or

threadless opening, terminating

fittings shall be of watertight strain

relief type such as Thomas & Betts

series 2920, 2920AL, 2920NM,

2520, 2631 or 2672. Fittings shall be

equipped with a beveled moisture

resistant/oil resistant synthetic rubber

bushing.

• Where space is limited inside the

enclosure, a female hub type fitting

such as Thomas & Betts series 2631

shall be furnished. A captive resilient

sealing ‘O’ ring shall be included to

positively protect against damage

from overtorquing.

2520 and 2530 Series

Liquidtight Flexible

Cord & Cable Fittings

2920NM Series

Nonmetallic Liquidtight

Flexible Cord & Cable Fittings

The Ranger™ Series

2920AL Series

Aluminum Liquidtight

Flexible Cord & Cable Fittings

The Ranger™ Series

2920S Series

Steel Liquidtight

Flexible Cord & Cable Fittings

The Ranger™ Series

2631 Series

Liquidtight Flexible

Cord & Cable Fittings

2672 Series

Flexible Cord Fittings

(Plastic)

2920SST Series

Stainless Steel Liquidtight

Flexible Cord & Cable Fittings

TCF Series

Aluminum Tray/Cord Fitting

CONFITMRO_EN_ALL.pdf 61 11/28/2011 11:05:27 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Suggested Specifications for Flexible Cord and Cable Fittings—continued

• Where flexible cord or cable exposed

to moisture is terminated into a

threadless opening using male threaded

hub type fittings such as Thomas &

Betts series 2520 or 2920, a suitable

moisture resistant/oil resistant

synthetic rubber gasket such as

Thomas & Betts series 5262 shall be

provided between the outside of box

or enclosure and fitting shoulder.

Resilient gasket shall be adequately

protected by and permanently

bonded to a metallic retainer.

• Where exposed to environmental

conditions that are more than normally

corrosive, watertight strain relief

fittings shall be of high impact

thermoplastic construction such

as Thomas & Betts series 2672 or

2920NM.

• Where flexible cord or cable passes

through either factory or field

punched, cut or drilled holes in metal

members, the cord or cable shall be

protected by thermoplastic bushing

such as Thomas & Betts series 3210,

3300. Bushing shall be firmly secured

in opening. Nylon bushed metallic

fittings such as Thomas & Betts

series 1942 may be substituted as

required.

• For wet location, fittings furnished

with synthetic rubber bushing such

as Thomas & Betts series 2530 or

2672 shall be installed.

Series 3300

Nonmetallic Sheathed

Cable & Flexible Cord

Fitting

Series 1942

Insulated Nipple

Series 3210

Knockout Bushings

Series 5262

Sealing Gasket

CONFITMRO_EN_ALL.pdf 62 11/28/2011 11:05:28 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Cat. No. Hub Diameter SV, SVO, SVT, SVTO

Straight 90° Size Range Cord Sizes

2671 2680 3/8 .125-.275 18-2, 18-3

Cat. No. Hub Diameter S, SO, ST, STO SJO, SJT, SJTO, SJ

Straight 90° Size Range Cord Sizes Cord Sizes

2920NM 4960NM 1/2 .125-.375 18-2, 18-3* 18-2, 18-3, 18-4, 16-2,

2930NM 4970NM 3/4 16-3, 16-4*, 14-2, 14-3*

2921NM 4961NM 1/2 18-3, 18-4, 18-5, 18-6, 18-7*

2931NM 4971NM 3/4 .310-.560 18-3, 18-4*, 18-5, 16-2* 16-3, 16-4, 16-5, 16-6*, 14-2,

2940NM — 1 14-3, 14-4, 12-2, 12-3, 12-4, 10-2

2922NM — 1/2 16-5, 16-6, 14-2, 14-3, 14-4,

2932NM 4972NM 3/4 .500-.750 14-5, 12-2, 12-3, 12-4, 12-5, 12-4, 10-2, 10-3, 10-4

2941NM — 1 10-2, 10-3, 10-4, 8-2

2942NM — 1 .700-.950 10-4, 10-5, 8-3, 8-4

—2688 1 .560-.690 14-3*, 14-4, 14-5*, 12-2, 12-3, 10-2*, 10-3, 10-4

12-4*, 10-2, 10-3*

—2685 1 .660-.780 14-5, 12-4*, 12-5, 10-3*, 10-4 10-4

2696 — 3/4 .770-.895 10-5, 8-2, 8-3*

—2686 1

2678 2687 1 .870-1.020 8-3*, 8-4*

2699 — 1 .890-1.090 8-4, 8-5*, 6-2, 6-3*, 6-4*, 4-2*

2702 — 1-1/4

2703 — 1-1/4 4-2*, 4-3, 2-2*

2704 — 1-1/4 1.270-1.470 4-4, 2-2*

2705 — 1-1/2 .890-1.150 8-4, 8-5, 6-2, 6-3, 6-4*, 4-2*

2706 — 1-1/2 1.140-1.400 6-5, 6-4*, 4-2*, 4-3, 4-4*,

2-2, 2-3*

2707 — 1-1/2 1.390-1.650 4-4*, 2-3*, 2-4

2708 — 2 1.190-1.530 6-5, 4-2*, 4-3, 4-4, 2-2, 2-3,

2-4*

2709 — 2 1.520-1.860 2-4*

2710 — 2 1.850-2.190

* Actual cord diameter must be determined before proper fitting can be selected.

Measure cord, if available, or refer to cord manufacturer’s catalogue.

How to Select T&B Flexible Cord Fittings

Step 1.

Determine Diameter Range in chart by using

cord size and type or by measuring the

diameter of your cord.

Step 2.

Determine catalogue number by choosing the

hub size and type (straight or 90°) for the

diameter range determined by step 1.

This chart can be used as a guide for selecting

the proper fitting for the U.L. Listed and CSA

Certified cords. Cords vary in sizes and cord

diameter should be measured whenever

possible.

CONFITMRO_EN_ALL.pdf 63 11/28/2011 11:05:28 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Flexible Cord and Power Cable Chart

AWG Size of Number of Conductors and Approximate O.D. (in.)

Type of Cord Conductors 2 Conductor 3 Conductor 4 Conductor

SV, SVO, SVT 18 .250 .260 —

SJ, SJO, 18 .300 .330 .360

SJT, SJTO 16 .330 .360 .390

14 .375 .395 .420

S, SO, ST, 18 .385 .400 .430

STO, and 16 .400 .425 .480

Portable 14 .530 .560 .605

Power Cables 12 .600 .635 .665

10 .640 .690 .745

8 .700-.840 .750-.910 .820-.990

6 .820-.930 .885-1.010 .975-1.100

4 1.080 1.170 1.270

3 1.170 1.240 1.340

2 1.270 1.340 1.480

1 1.440 1.510 1.680

1/0 1.520 1.650 1.790

2/0 1.650 1.750 1.930

3/0 1.770 1.890 2.070

4/0 1.920 2.070 2.260

250 2.160 2.390 —

14 — — .410

12 — — .450

10 — — .530

Bus Drop 8 — — .670

Cables 6 — — .850

4 — — .950

2 — — 1.000

Note: The above dimensions are approximate and may vary depending upon the

manufacturer.

CONFITMRO_EN_ALL.pdf 64 11/28/2011 11:05:28 AM

T&B Conduit Fittings

Flexible Cord and cable Fittings

2520 Series

2631 Series

Specifications — Liquidtight Flexible Cord and Cable Fittings

Gland

Retaining

Ring

Bushing

Body

Sealing

Gasket

(E)

(D)

(A)

(B)

Application

• A liquidtight fittings to connect

flexible cord or power cable to

a box or enclosure and provide

adequate strain relief.

Features

• Liquidtight connection with box

or enclosure is assured by:

(1) Taper threaded hub on

2520 series for female hub

application (A).

(2) Using sealing ring series 5262 with

2520 series for knockout

application (B).

(3) Captivated sealing ‘O’ ring on

2631 series (C).

• Neoprene bushing makes liquidtight

installation; applies pressure against

cable the full length of bushing (D).

• Thermoplastic or stainless steel

retaining ring (E).

(1) Will not abrade cord/cable jacket.

(2) Reduces installing torque effort.

• U.L. Listed for liquidtightness, strain

relief and as an outlet bushing; CSA

certified watertight.

Standard Material

Gland, Body Steel/Malleable

Iron/Zinc Die Cast

Retaining Ring Thermoplastic/

Stainless Steel

Bushing Neoprene

‘O’ Ring Buna N

Standard Finish

Electro Zinc Plated & Chromate

Coated

Range

• 2520 Series, straight

0.125” outside diameter to 3.200”

outside diameter Cord or Cable

• 2200 Series, 45°

0.125” outside diameter to 1.485”

outside diameter Cord or Cable

• 2267 Series, 90°

0.125” outsidediameter to 1.875”

outside diameter Cord or Cable

Cord/Cable Type S, SO, SV, ST,

STO, SJ, SJO, SJT, SJTO, SVO & SVT

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NFPA 70-2008 (ANSI)

2631 Series

Gland

Retaining

Ring

Bushing

Body

Nipple

(E)

(D)

(C)

CONFITMRO_EN_ALL.pdf 65 11/28/2011 11:05:28 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Fig. 1

Throat Dia.

Fig. 2

Throat Dia.

Liquidtight Strain Relief Fittings

Cable Size Throat

Range Hub Dia. Dimensions (in.)

Cat. No. min.-max. Size (min.) Fig. A B C

2516†(.060-.125) 1/4” 23/64” 2 53/64 1-7/16 15/32

2517†(.120-.250) 1/4” 23/64” 2 53/64 1-7/16 15/32

2518†(.060-.150) 3/8” 29/64” 2 31/32 1-1/2 15/32

2519†** (.150-.300) 3/8” 29/64” 2 31/32 1-1/2 15/32

2520 (.125-.250) 1/2” 9/16” 1 1-5/32 1-11/16 5/8

2521 (.250-.375) 1/2” 9/16” 1 1-5/32 1-11/16 5/8

2522 (.375-.500) 1/2” 9/16” 1 1-5/32 1-11/16 5/8

2523 (.450-.560) 1/2” 9/16” 1 1-5/32 1-11/16 5/8

2524* (.500-.625) 1/2” 5/8” 1 1-3/8 1-3/4 5/8

2525* (.625-.750) 1/2” 5/8” 1 1-3/8 1-3/4 5/8

2530 (.125-.250) 3/4” 13/16” 1 1-3/8 1-3/4 9/16

2531 (.250-.375) 3/4” 13/16” 1 1-3/8 1-3/4 9/16

2532 (.375-.500) 3/4” 13/16” 1 1-3/8 1-3/4 9/16

2534 (.500-.625) 3/4” 13/16” 1 1-3/8 1-3/4 9/16

2535 (.625-.750) 3/4” 13/16” 1 1-3/8 1-3/4 9/16

2536* (.750-.880) 3/4” 3/4” 1 1-11/161-15/16 5/8

2541 (.250-.375) 1” 49/64” 1 1-3/8 1-23/32 9/16

2542 (.375-.500) 1” 49/64” 1 1-3/8 1-23/32 9/16

2544 (.500-.625) 1” 49/64” 1 1-3/8 1-23/32 9/16

2545 (.625-.750) 1” 49/64” 1 1-3/8 1-23/32 9/16

2546 (.750-.875) 1” 63/64” 1 1-11/16 1-7/8 23/32

2547 (.875-.985) 1” 63/64” 1 1-11/16 1-7/8 9/16

2548* (.880-1.065) 1” 29/32” 1 2-3/32 2-3/8 25/32

2549* (1.065-1.205) 1” 29/32” 1 2-3/32 2-3/8 25/32

2558 (.880-1.065) 1-1/4” 1-17/64” 1 2-3/32 2-5/32 13/16

2559 (1.065-1.205) 1-1/4” 1-17/64” 1 2-3/32 2-5/32 13/16

2556* (1.187-1.375) 1-1/4” 1-1/4” 1 2-11/32 2-1/2 13/16

2557* (1.375-1.485) 1-1/4” 1-1/4” 1 2-11/32 2-1/2 13/16

2562 (.812-1.000) 1-1/2” 1-7/16” 1 2-11/32 2-1/2 11/16

2563 (1.000-1.187) 1-1/2” 1-7/16” 1 2-11/32 2-7/16 11/16

2564 (1.187-1.375) 1-1/2” 1-7/16” 1 2-11/32 2-7/16 11/16

2565* (1.375-1.625) 1-1/2” 1-29/64” 1 2-13/16 2-5/8 13/16

2573 (1.125-1.375) 2” 1-7/8” 1 2-13/16 2-5/8 13/16

2574 (1.375-1.625) 2” 1-7/8” 1 2-13/16 2-5/8 11/16

2575 (1.625-1.875) 2” 1-7/8” 1 2-13/16 2-5/8 11/16

2576* (1.750-1.965) 2” 1-29/32” 1 3-7/32 3-1/2 27/32

2577* (1.937-2.187) 2” 1-29/32” 1 3-7/32 3-1/2 27/32

2584 (1.750-1.965) 2-1/2” 2” 1 3-7/32 3-3/4 1-1/32

2585* (1.937-2.187) 2-1/2” 2” 1 3-7/32 3-3/4 1-1/32

2586* (2.156-2.360) 2-1/2” 2-5/32” 1 3-15/16 4-1/4 1-1/32

2587* (2.350-2.565) 2-1/2” 2-5/32” 1 3-15/16 4-1/4 1-1/32

2592 (2.156-2.360) 3” 2-13/32” 1 3-15/16 4-1/4 1-1/32

2593 (2.350-2.565) 3” 2-13/32” 1 3-15/16 4-1/4 1-1/32

2594 (2.535-2.750) 3” 2-13/32” 1 3-15/16 4-1/4 1-1/32

2595* (2.735-2.985) 3” 2-13/16” 1 4-11/164-13/16 1-1/8

2596* (2.970-3.220) 3” 2-13/16” 1 4-11/164-13/16 1-1/8

* Remove sufficient outer covering of cable to permit conductors to pass thru fitting body.

†U.L. not applicable.

** Not CSA Certified.

Complies with JIC standards.

U.L. Listed as liquidtight strain relief, and outlet bushing. CSA certified watertight when used

with 5262 Series Sealing Ring. Gasket (Sold separately).

Temperature rating: 105°C.

For Wiremesh Grips refer to page 80.

5262 Series

Sealing Ring Gasket

sold separately

CONFITMRO_EN_ALL.pdf 66 11/28/2011 11:05:28 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Swing Radius

90° with neoprene bushings, tapered hub

threads, malleable iron.

Strain Relief Fittings

Cable Size Hub Dimensions (in.) Throat

Cat. No. min.-max. Size A B C Dia.

2267 (.125-.250) 1/2” 1-5/32 1-23/32 5/8 19/32

2268 (.250-.375) 1/2” 1-5/32 1-23/32 5/8 19/32

2269 (.375-.500) 1/2” 1-5/32 1-23/32 5/8 19/32

2270 (.450-.560) 1/2” 1-5/32 1-23/32 5/8 19/32

2250* (.500-.625) 1/2” 1-3/8 1-11/16 9/16 39/64

2251* (.625-.750) 1/2” 1-3/8 1-11/16 9/16 39/64

2252 (.125-.250) 3/4” 1-3/8 1-3/4 41/64 25/32

2271 (.250-.375) 3/4” 1-3/8 1-5/8 41/64 25/32

2272 (.375-.500) 3/4” 1-3/8 1-5/8 41/64 25/32

2273 (.500-.625) 3/4” 1-3/8 1-5/8 41/64 25/32

2274* (.620-.750) 3/4” 1-3/8 1-5/8 41/64 25/32

2253* (.750-.880) 3/4” 1-11/16 1-31/32 9/16 25/32

2254 (.375-.500) 1” 1-3/8 2 13/16 1

2255 (.500-.625) 1” 1-3/8 2 13/16 1

2256* (.625-.750) 1” 1-3/8 2 13/16 1

2275 (.750-.875) 1” 1-11/16 2 13/16 1

2276 (.875-.985) 1” 1-11/16 2 13/16 1

2257* (.880-1.065) 1” 2-3/32 2-21/32 25/32 15/16

2258* (1.065-1.205) 1” 2-3/32 2-21/32 25/32 15/16

2277 (.880-1.065) 1-1/4” 2-3/32 2-7/8 27/32 1-5/16

2278 (1.065-1.205) 1-1/4” 2-3/32 2-7/8 27/32 1-5/16

2279* (1.187-1.375) 1-1/4” 2-11/32 2-13/16 13/16 1-11/32

2280* (1.375-1.485) 1-1/4” 2-11/32 2-13/16 13/16 1-11/32

2281 (.812-1.000) 1-1/2” 2-11/32 2-7/8 13/16 1-15/32

2282 (1.000-1.187) 1-1/2” 2-11/32 2-7/8 13/16 1-15/32

2283* (1.187-1.375) 1-1/2” 2-11/32 2-7/8 13/16 1-15/32

2284 (1.125-1.375) 2” 2-13/16 3-1/4 27/32 1-31/32

2285 (1.375-1.625) 2” 2-13/16 3-1/4 27/32 1-31/32

2286 (1.625-1.875) 2” 2-13/16 3-1/4 27/32 1-31/32

* Remove sufficient outer covering of cable to permit conductors to pass through

fitting body.

Complies with J.I.C. standards and Federal Specs W-F-406B, W-F-408B.

Meets Coast Guard CG293

For Wiremesh Grips refer to page 80.

CONFITMRO_EN_ALL.pdf 67 11/28/2011 11:05:28 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Strain Relief Fittings

Cable Size Hub Dimensions (in.) Throat

Cat. No. min.-max. Size A B C Dia.

2200 (.125-.250) 1/2” 1-5/32 1-9/32 9/16 37/64

2201 (.250-.375) 1/2” 1-5/32 1-9/32 9/16 37/64

2202 (.375-.500) 1/2” 1-5/32 1-9/32 9/16 37/64

2203 (.450-.560) 1/2” 1-5/32 1-9/32 9/16 37/64

2204* (.500-.625) 1/2” 1-3/8 1-13/32 9/16 37/64

2205* (.625-.750) 1/2” 1-3/8 1-13/32 9/16 37/64

2206-TB (.125-.250) 3/4” 1-3/8 1-13/32 5/8 25/32

2207-TB (.250-.375) 3/4” 1-3/8 1-13/32 5/8 25/32

2208-TB (.375-.500) 3/4” 1-3/8 1-13/32 5/8 25/32

2209 (.500-.625) 3/4” 1-3/8 1-13/32 5/8 25/32

2210 (.625-.750) 3/4” 1-3/8 1-13/32 5/8 25/32

2211* (.750-.880) 3/4” 1-11/16 1-1/2 1-1/2 3/4

2213 (.375-.500) 1” 1-3/8 1-1/2 25/32 15/16

2214 (.500-.625) 1” 1-3/8 1-1/2 25/32 15/16

2215 (.625-.750) 1” 1-3/8 1-1/2 25/32 15/16

2216 (.750-.875) 1” 1-11/16 1-15/32 25/32 15/16

2217* (.875-.985) 1” 1-11/16 1-15/32 25/32 15/16

2218* (.880-1.065) 1” 2-3/32 1-31/32 25/32 15/16

2219* (1.065-1.205) 1” 2-3/32 1-31/32 25/32 15/16

2220-TB* (.880-1.065) 1-1/4” 2-3/32 1-29/32 13/16 1-5/16

2221* (1.065-1.205) 1-1/4” 2-3/32 1-29/32 13/16 1-5/16

2222* (1.187-1.375) 1-1/4” 2-11/32 2-1/4 13/16 1-21/64

2223* (1.375-1.485) 1-1/4” 2-11/32 2-1/4 13/16 1-21/64

* Remove sufficient outer covering of cable to permit conductors to pass through

fitting body.

U.L. Listed as liquidtight strain relief, and outlet bushing.

CSA certified watertight.

For Wiremesh Grips refer to page 80.

Swing Radius

45° with neoprene bushings, tapered hub

threads, malleable iron.

CONFITMRO_EN_ALL.pdf 68 11/28/2011 11:05:29 AM

T&B Conduit Fittings

Flexible Cord and Cable fittings

CHASE®Liquidtight Cord Fittings

Cable Size Range Hub Throat Dimensions (in.)

Cat. No. min.-max. Size Diam. A B

2631 (.125-.250) 1/2” 9/16” 1-1/16 1-5/8

2632 (.250-.375) 1/2” 9/16” 1-1/16 1-5/8

2633 (.375-.500) 1/2” 9/16” 1-1/16 1-5/8

2634 (.450-.560) 1/2” 9/16” 1-1/16 1-5/8

2637 (.125-.250) 3/4” 25/32” 1-3/8 1-3/16

2638 (.250-.375) 3/4” 25/32” 1-3/8 1-3/16

2639 (.375-.500) 3/4” 25/32” 1-3/8 1-3/16

2640 (.500-.625) 3/4” 25/32” 1-3/8 1-3/16

2641 (.625-.750) 3/4” 25/32” 1-3/8 1-3/16

CSA certified watertight.U.L. Listed as liquidtight strain relief, and outlet bushing.

Temperature Rating: 105°C.

Chase Liquidtight Cord Fittings are ideal for installation where space is limited inside

the enclosure.

Multi-Hole Cord Grip

Hub No. of Cord Dimensions (in.)

Cat. No. Size Diam. Diam. A B C

2520-2 1/2” 2 .220 1.125 1.687 .625

2530-2 3/4” 2 .220 1.375 1.750 .625

2531-2 3/4” 2 .260 1.375 1.750 .625

2531-3 3/4” 3 .260 1.375 1.750 .625

2541-2* 1” 2 .300 1.625 1.718 .781

2542-2* 1” 2 .375 1.625 1.718 .781

2540-3 1” 3 .225 1.625 1.718 .781

2541-3 1” 3 .300 1.625 1.718 .781

2540-4 1” 4 .220 1.625 1.718 .781

2555-2 1-1/4” 2 .500 2.093 2.375 .812

Range of cord diameter ±.010”.

In many applications you have only room for one fitting but you need to run two cables, for

example, proximity switches. Now you can provide strain relief and liquidtight protection with

T&B’s new multi-hole liquidtight strain relief fittings. With the ever increasing number of signal

cables, now you have a solution to the problem of how to strain relieve multiple cables in one

fitting.

*UL Listed only

Temperature Rating: 105°C.

CONFITMRO_EN_ALL.pdf 69 11/28/2011 11:05:29 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

The Ranger®Series — Liquidtight Strain Relief Fittings

Standard Material/Finish

2920S Series

4920 Series 2920NM Series 2920AL Series

4960 Series 4960NM Series 4960AL Series

Body Steel (ST) Nylon Aluminum (ST)

45° & 90° (Weather Stabilized) Malleable Iron (90°)

(Malleable Iron)

Gland Steel Nylon Aluminum

(Weather Stabilized)

Grip Plastic Nylon Aluminum

(Weather Stabilized)

Bushing Santoprene Oil Resistant Aluminum

Elastomer

Liquidtight Strain Relief Fittings—Straight

Hub Throat Cord Range Dimensions (in.)

Cat. No. Size Dia. min.-max. A B C

2920S 1/2 9/16 .125-.375 1-1/8 1-3/4 5/8

2921S 1/2 9/16 .310-.560 1-1/8 1-3/4 5/8

2922S* 1/2 9/16 .500-.750 1-3/8 1-3/4 5/8

2930S 3/4 13/16 .125-.375 1-3/8 1-25/32 3/4

2931S 3/4 13/16 .310-.560 1-3/8 1-25/32 3/4

2932S 3/4 13/16 .500-.750 1-3/8 1-25/32 3/4

2940S 1 1-1/16 .310-.560 1-3/8 1-3/4 1-3/16

2941S 1 1-1/16 .500-.750 1-3/8 1-3/4 1-3/16

2942S 1 31/32 .700-.950 1-5/8 1-7/8 1-3/16

*It may be necessary to remove sufficient outer covering of cable to permit conducters to

pass through the fitting body.

The only fitting to take a .250 inch

cable range.

New materials and computer aided

designs helped T&B develop a strain

relief fitting that will take twice the cable

range of ordinary strain relief fittings.

Features

• Extended range with superior strain

relief.

• Reduced overall size, fits into tighter

spaces.

• Gland nut designed to restrict cable

bending.

Application

A liquidtight fitting to secure flexible cord

or power cable to a box or enclosure

and provide strain relief.

Range

Series Hub Size

.125” thru .950” 2920S 1/2 thru 1”

4920 1/2 thru 1”

4960 1/2 thru 1”

2920AL 1/2 thru 1”

4960AL 1/2 thru 1”

2920NM 1/2 thru 1”

.125 thru .750” 4960NM 1/2 thru 3/4”

Cat. No. Hub

Size

Throat

Dia.

Color Range

min.-max.

Dimensions (in.)

A B M

2920 1/2 9/16 .125-.375 1-1/8 1-3/4 5/8

2921 1/2 9/16 .310-.560 1-1/8 1-3/4 5/8

2922 1/2 9/16 .500-.750 1-3/8 1-3/4 5/8

2930 3/4 13/16 .125-.375 1-3/8 1-25/32 3/4

2931 3/4 13/16 .310-.560 1-3/8 1-25/32 3/4

2932 3/4 13/16 .500-.750 1-3/8 1-25/32 3/4

2940 11-1/16 .310-.560 1-3/8 1-3/4 1-3/16

2941 11-1/16 .500-.750 1-3/8 1-3/4 1-3/16

2942 131/32 .700-.950 1-5/8 1-7/8 1-3/16

Liquidtight Strain Relief Fittings

70-E.pdf 1 1/17/2012 10:05:40 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

The Ranger®Series

Liquidtight Strain Relief Fittings—45° Angle

Hub Throat Dimensions (in.)

Cat. No. Size Dia. Cord Range A B C

4920 1/2 37/64 .125-.375 1-1/8 1-5/16 9/16

4921 1/2 37/64 .310-.560 1-1/8 1-5/16 9/16

4922 1/2 37/64 .500-.750 1-3/8 1-7/16 9/16

4932 3/4 25/32 .500-.750 1-3/8 1-7/16 5/8

4933 3/4 25/32 .700-.950 1-5/8 1-17/32 1-1/2

Liquidtight Strain Relief Fittings—90° Angle

Cat. Hub Throat Dimensions (in.)

No. Size Dia. Cord Range A B C

4960 1/2 19/32 .125-.375 1-1/8 1-3/4 5/8

4961 1/2 19/32 .310-.560 1-1/8 1-3/4 5/8

4962 1/2 19/32 .500-.750 1-3/8 1-24/64 5/8

4970 3/4 25/32 .125-.375 1-3/8 1-25/32 11/16

4971 3/4 25/32 .310-.560 1-3/8 1-25/32 11/16

4972 3/4 25/32 .500-.750 1-3/8 1-25/32 11/16

Swing Radius

CONFITMRO_EN_ALL.pdf 71 11/28/2011 11:05:29 AM

Aluminum Liquidtight Strain Relief Fittings—

Straight

Hub Throat Dimensions (in.)

Cat. No. Size Diam. Cord Range A B C

2920AL 1/2 9/16 .125-.375 1-1/8 1-3/4 5/8

2921AL 1/2 9/16 .310-.560 1-1/8 1-3/4 5/8

2922AL* 1/2 9/16 .500-.750 1-5/16 1-3/4 5/8

2930AL 3/4 13/16 .125-.375 1-5/16 1-25/32 3/8

2931AL 3/4 13/16 .310-.560 1-5/16 1-25/32 3/4

2932AL 3/4 13/16 .500-.750 1-5/16 1-25/32 3/4

2940AL 1 1-1/16 .310-.560 1-5/16 1-3/4 1-1/16

2941AL 1 1-1/16 .500-.750 1-5/16 1-3/4 1-1/16

2942AL 1 31/32 .700-.950 1-9/16 1-7/8 31/32

* It may be necessary to remove sufficient outer covering of cable to permit conductors

to pass through fitting body.

Aluminum Liquidtight Strain Relief Fittings—

90° Elbow

Trade or Throat Dimensions (in.)

Cat. No. Hub Size Diam. Cord Range A B C D

4960AL 1/2 9/16 .125-.375 1-1/8 1-3/4 5/8 1-5/16

4961AL 1/2 9/16 .360-.560 1-1/8 1-3/4 5/8 1-5/16

4962AL* 1/2 9/16 .500-.750 1-5/16 1-23/64 5/8 1-3/8

4970AL 3/4 25/32 .125-.375 1-5/16 1-25/32 11/16 1-15/32

4971AL 3/4 25/32 .310-.560 1-5/16 1-25/32 11/16 1-15/32

4972AL 3/4 25/32 .500-.750 1-5/16 1-25/32 11/16 1-15/32

4980AL 1 15/16 .310-.560 1-5/16 2-1/32 13/16 1-3/4

4981AL 1 15/16 .500-.750 1-5/16 2-1/32 13/16 1-3/4

4982AL 1 15/16 .700-.950 1-9/16 2-11/16 13/16 2

* It may be necessary to remove sufficient outer covering of cable to permit conductors to

pass through fitting body.

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Body: malleable iron

Gland Nut: aluminum

Body and gland nut are aluminum.

Across

Corners

CONFITMRO_EN_ALL.pdf 72 11/28/2011 11:05:29 AM

T&B Conduit Fittings

T&B Ranger®Stainless Steel Liquidtight Cord Fittings

Food Processing

Pharmaceutical

Processing Pulp & Paper Mills

Wastewater Treatment Saltwater Applications Petrochemical Refining

Beveled Rubber Bushing Ensures

Superior Compression and

Sealing

Type 304 Stainless Steel Construction for Your Harshest Environments!

Until now, there has been no ideal solution for liquidtight connections of portable

cord to a box or enclosure in corrosive environments. Steel fittings rust and non-

metallic fittings cannot withstand high temperatures or ultraviolet exposure.

In response to customer demand, Thomas & Betts has developed the latest addition

to its high-performance line of T&B Ranger®Cord Fittings. Made of Type 304

stainless steel, T&B Ranger®Stainless Steel Liquidtight Cord Fittings stand up to

highly corrosive environments – such as washdown areas in food and beverage or

pharmaceutical processing – as well as high temperatures and UV exposure.

Like all T&B Ranger®Liquidtight Cord Fittings, the new stainless steel fittings offer

twice the cord diameter range of similar fittings, so you can do more with fewer sizes

to order and stock. They form a non-slip mechanical grip, providing a liquidtight seal

and the strain relief required for flexible portable cord connections.

•Each fitting covers a 0.25” cord diameter

range – twice that of ordinary strain relief

fittings

•Superior corrosion resistance in washdown

areas and other corrosive environments

•Stands up to heat and UV exposure better

than non-metallic fittings

•Beveled, moisture and oil resistant synthetic

rubber bushing system ensures superior

compression and sealing of fitting to cord

•Bushing marked with cord range for easy

Identification out of box

• 2920 Series steel/malleable iron in straight, 45º and 90º

•2920AL Series aluminum in straight and 90º

•2920NM Series non-metallic in straight and 90º

Also available in other materials to meet all your cord-fitting needs!

T&B Stainless Steel Cord Fittings – 1/4” - 3/8” Hub Sizes

Catalogue

Number

Hub

Size (in.)

Cord Dia.

Range (in.)

Dimensions (in.)

A B C

2918SST 1/4 0.118 - 0.256 1.000 0.250 0.625

2919SST 3/8 0.157 - 0.315 1.313 0.438 0.750

T&B Stainless Steel Cord Fittings – 1/2” - 1” Hub Sizes

Catalogue

Number

Hub

Size (in.)

Cord Dia.

Range (in.)

Dimensions (in.)

A B C

2920SST 1/2 0.125 - 0.375 1.935 0.610 1.125

2921SST 1/2 0.310 – 0.560 1.935 0.610 1.125

2922SST 1/2 0.500 – 0.750 2.003 0.610 1.125

2930SST 3/4 0.125 – 0.375 2.063 0.630 1.125

2931SST 3/4 0.310 – 0.560 2.063 0.630 1.125

2932SST 3/4 0.500 – 0.750 2.063 0.630 1.125

2940SST 10.310 – 0.560 2.178 0.785 1.500

2941SST 10.500 – 0.750 2.218 0.785 1.500

2942SST 10.700 – 0.950 2.218 0.785 1.500

CONFITMRO_EN_ALL.pdf 73 11/28/2011 11:05:29 AM

T&B Conduit Fittings

Stainless Steel Liquidtight Conduit Connectors

Liquidtight Conduit Connectors

Cat. Dimensions Std. Pkg. UPC

Number Size A B C Qty. Number

Straight

5331SST *3/8" 1.360" 1.02" — 25 78621097764

5332SST 1/2" 1.360" 1.18" — 25 78621084482

5333SST 3/4" 1.388" 1.37" — 25 78621074480

5334SST 1" 1.562" 1.77" — 5 78621096334

5335SST 11/4" 1.720" 2.12" — 20 78621097765

5336SST 11/2" 2.020" 2.48" — 5 78621097766

5337SST 2" 2.335" 3.04" — 2 78621097767

45oAngled

5341SST *3/8" 1.84" 1.02" 1.43" 25 78621097775

5342SST 1/2" 1.62" 1.18" 2.04" 25 78621097776

5343SST 3/4" 2.32" 1.37" 1.93" 10 78621097777

5344SST 1" 2.86" 1.77" 2.37" 5 78621097778

5345SST 11/4" 3.33" 2.12" 2.80" 5 78621097779

5346SST 11/2" 3.94" 2.48" 3.39" 2 78621097780

5347SST 2" 4.73" 3.04" 4.23" 1 78621097781

Cat. Dimensions Std. Pkg. UPC

Number Size A B C Qty. Number

90oAngled

5351SST *3/8" 1.95" 1.02" 1.84" 25 78621097768

5352SST 1/2" 2.12" 1.18" 2.07" 25 78621097769

5353SST 3/4" 2.47" 1.37" 2.44" 10 78621097770

5354SST 1" 2.98" 1.77" 2.90" 5 78621097771

5355SST 11/4" 3.53" 2.12" 3.36" 5 78621097772

5356SST 11/2" 4.16" 2.48" 3.88" 2 78621097773

5357SST 2" 8.60" 3.04" 4.69" 1 78621097774

Sealing Gasket

5261 3/8" — — — 50 78621005261

5262 1/2" — — — 50 78621005262

5263 3/4" — — — 25 78621005263

5264 1" — — — 25 78621005264

5265 11/4" — — — 5 78621005265

5266 11/2" — — — 5 78621005266

5267 2" — — — 5 78621005267

The Strength of Steel — with Superior

Corrosion-Resistance!

Until now, there’s been no ideal conduit fitting solution for use in

heavily corrosive environments. Traditional metallic fittings corrode

and require frequent replacement. Non-metallic fittings offer less

strength, lower UV-resistance, and don’t stand up well in extreme

temperatures.

T&B Stainless Steel Liquidtight Conduit Connectors are constructed

of 304 stainless steel to resist corrosion while offering high strength,

high UV-resistance, and high endurance. Choose among a full range

of fittings in straight, 45o, and 90oangled configurations for 3/8" to 2"

conduit sizes. Look for the distinctive blue insulator and sealing ring

for assurance of T&B quality.

•Ideal for industrial MRO and OEM applications in food and

beverage, pharmaceutical, petrochemical, waste water, salt water,

and other corrosive environments

•Connects metallic-cored liquidtight conduit to a box

or enclosure

•304 stainless steel body and gland-nut resists corrosion far better

than other metallic fittings

•Stronger, more UV-resistant than nonmetallic fittings

•Available in straight, 45o, and 90oangled configurations to fit

conduit from 3/8" to 2"

•UL®Listed Ratings: 3, 3R, 4, 4X

•5262 Sealing Ring Gasket (sold separately) includes a stainless

steel retaining ring to prevent elongation of the gasket and is made

from Santoprene™material, ensuring a superior seal

5262 Series

Sealing Ring Gasket

sold separately

Locknut not included

3/8” conduit fitting has 3/8” hub

CONFITMRO_EN_ALL.pdf 74 11/28/2011 11:05:31 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

The Ranger®Series — Nylon Cord Grip Fitting

A T&B “RANGER” Exclusive

Smaller shape: 30% smaller envelope

Wide range: twice the cable range

• Reduced size means fittings can be placed closer together.

• Wider range means one fitting can cover twice the cable range of others.

• Nonmetallic means corrosion resistance.

Nonmetallic Liquidtight Strain Relief Fitting—Straight

Trade or Throat Dimensions (in.)

Cat. No. Hub Size Diam. Cord Range A B C

2920NM 1/2” 9/16 .125-.375 1-7/32 2-1/8 5/8

2921NM 1/2” 9/16 .310-.560 1-7/32 2-1/8 5/8

2922NM 1/2” 9/16 .500-.750 1-13/32 2-5/32 5/8

2930NM 3/4” 3/4 .125-.375 1-13/32 2-3/16 5/8

2931NM 3/4” 3/4 .310-.560 1-13/32 2-3/16 5/8

2932NM 3/4” 3/4 .500-.750 1-13/32 2-3/16 5/8

2940NM 1” 29/32 .310-.560 1-13/32 2-11/32 25/32

2941NM 1” 29/32 .500-.750 1-13/32 2-11/32 25/32

2942NM 1” 29/32 .700-.950 1-43/64 2-3/8 25/32

Nonmetallic Liquidtight Strain Relief fitting—

90° Elbow

Trade or Throat Dimensions (in.)

Cat. No. Hub Size Diam. Cord Range A B C

4960NM 1/2” 9/16 .125-.375 1-7/32 1-1/4 5/8

4961NM 1/2” 9/16 .310-.560 1-7/32 1-1/4 5/8

4970NM 3/4” 3/4 .125-.375 1-13/32 1-3/8 5/8

4971NM 3/4” 3/4 .310-.560 1-13/32 1-3/8 5/8

4972NM 3/4” 3/4 .500-.750 1-13/32 1-3/8 5/8

• Weather Stabilized Nylon

• U.L. 94-V2

• Temperature Rating: -34ÞC to +105ÞC

• Meets Coast Guard CG293

• New Reduced Size

• Smaller Footprint

90° elbow, new reduced size, smaller footprint.

• Weather Stabilized Nylon

• U.L. 94-V2

• Temperature Rating: -34ÞC to +105ÞC

• Meets Coast Guard CG293

CONFITMRO_EN_ALL.pdf 75 11/28/2011 11:05:31 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Large Tapered Bushing

High-Performance Chuck Grip

Tray Cable Applications

Portable Cord Applications

One heck of a grip!

Increased Safety

for Hazardous Locations

Introducing the Silver Grip™Tray-Cord Fitting™- the safe,

yet cost-efficient choice for increased safety when terminating

portable cord and tray cable in hazardous locations.

Designed for use in Class I, Gas and Vapour environments,

the Silver Grip™Tray-Cord Fitting™provides efficient strain relief

for cables entering enclosures and raceways, and for

cords used on portable equipment.

• Corrosion-resistant, non-magnetic

aluminum construction

• Tapered neoprene bushing and O-ring

seal out moisture and dirt ingress

• Chuck grip provides high mechanical

pull-out performance. Exceeds

applicable requirements.

• Hand-tightens — no tools required

• Now available in 316 stainless steel

• 90°C temperature rating

C US

Silver Grip™—TCF

™Series Tray-Cord Fitting

76-e.pdf 1 6/1/2012 4:04:35 PM

T&B Conduit Fittings

Tray Cable

Complies with IEC requirements for Class I, Zone 2 locations when used with enclosures containing no

arcing or sparking devices. For enclosures with arcing or sparking devices, TCF®fittings must be

used in combination with a certified Class I hazardous location sealing fitting.

Portable Cord

Complies with IEC requirements for Class I, Zone 1 locations when used with enclosures containing no

arcing or sparking devices. For enclosures with arcing or sparking devices, TCF®fittings must be used

in combination with a certified Class I hazardous location sealing fitting.

* When cord will not fit through body, strip cord jacket and trim fillers if required. Insert cable ensuring the outer jacket reaches the end

of the bushing as shown. Tighten gland nut onto body.

Ordering Information

Applications

• File Number LR4484, Certificate Number 1388229

• CSA Class 4418-05 Fittings for Hazardous Locations Class I, Zone 1 Ex e II, IP66; Type 4/4X, (CSA)

• CSAus Class 4418-85 Fittings for Hazardous Locations Class I, Zone 1, A Ex e II, IP66; Type 4/4X, (CSAus)

N.B.: Tray cable is not suitable for use in Zone 1 locations.

Portable cord can be used in Zone 1 applications only when installed on portable equipment.

TCF ®Series — Tray / Cord Fitting

O-Ring

Body

Bushing

Chuck

Grip

Maximum

Opening

Gland

Nut

For stainless steel (316), replace AL for SS6 (up to 1“ only)

Utilisation

• For use with unarmored cable Types suitable for use in Class I, Zone 1 (e.g.) Extra Hard Usage Cord)

• Series TCF Cable Glands, when used with Tray Cables are suitable to be installed in Class I, Zone 2/Div. 2

Classified Hazardous Locations Areas according to CEC/NEC Wiring Method, or subject to Local Inspection

Authority having jurisdiction.

Hub

Size

NPT

Catalogue

Number

Throat

Diameter

(in.)

Minimum

Cable Dia.

(in.)

Maximum

Opening

(in.)

1/2 TCF050-27AL 0.330 0.150 0.270

1/2 TCF050-40AL 0.540 0.250 0.400

1/2 TCF050-54AL 0.540 0.400 0.540

1/2 TCF050-67AL 0.540* 0.540 0.670

1/2 TCF050-78AL 0.540* 0.660 0.780

3/4 TCF075-40AL 0.540 0.250 0.400

3/4 TCF075-54AL 0.540 0.400 0.540

3/4 TCF075-67AL 0.780 0.540 0.670

3/4 TCF075-78AL 0.780 0.660 0.780

3/4 TCF075-88AL 0.765* 0.770 0.880

1TCF100-78AL 0.980 0.660 0.780

1TCF100-88AL 0.980 0.770 0.880

1TCF100-100AL 0.980* 0.870 1.000

1TCF100-109AL 0.980 0.940 1.090

1-1/4 TCF125-109AL 1.255 0.890 1.090

1-1/4 TCF125-128AL 1.255* 1.080 1.280

1-1/4 TCF125-147AL 1.255* 1.270 1.470

1-1/2 TCF150-115AL 1.470 0.890 1.150

1-1/2 TCF150-140AL 1.470 1.140 1.400

1-1/2 TCF150-165AL 1.470* 1.390 1.650

2TCF200-153AL 1.896 1.190 1.530

2TCF200-186AL 1.896 1.520 1.860

2TCF200-219AL 2.062* 1.850 2.190

2-1/2 TCF250-252AL 2.466* 2.120 2.520

3TCF300-278AL 2.780 2.380 2.780

3TCF300-304AL 3.050 2.640 3.040

3TCF300-330AL 3.068* 2.900 3.300

CONFITMRO_EN_ALL.pdf 77 11/28/2011 11:05:32 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

The Canadian Electrical Code states

that tray cable in hazardous locations

can be used either within the cable

tray, or outside the tray - provided

there is additional protection. The

TrayStar TM fitting was designed and

engineered for either application and

comes complete with the bushing,

ground cone and sealing ring for

different product applications.

Ease of Installation

Installation is quick and easy. When

used on metallic liquidtight conduit, the

fitting hub size correlates with that of

the conduit trade size. (i.e. 1/2” fitting

accomodates 1/2” conduit). The

bushings, when utilized, are designed

to accomodate a broad range of tray

cable diameters. Either liquid or putty

sealing compound can be used for a

positive, gastight seal. The compound

is ordered separately to allow for

flexibility in making the correct

selection for various types of

installations. The sealing compounds

cure in just a few hours. The

TrayStar TM fitting also has disconnect

capability: the cable can be

disconnected and reconnected after

being sealed.

The unique hexagonal gland nut is

conveniently grooved for screwdriver

installation in extremely cramped areas.

The gland nut is also clearly identified

with the catalogue number and CSA

approvals. It is also anodized an aqua-

blue colour to identify it as a

Hazardous Location, Tray Cable Fitting.

Superior Construction

TrayStar TM fittings have a low-profile

compact design and are made of

copper-free aluminum for long-lasting

trouble-free service. Fittings are

precision machined for superior fit and

ease of installation.

Inside Tray —Used with a neoprene bushing,

TrayStar TM terminates tray cable within the tray

itself.

Sealing

compound

Hub

Bushing

Retainer

With conduit

Double

face tape

Sealing

compound

Ground

cone

Sealing

ring

Gland

nut

Putty insert

Body

SC4-KIT

SC65

For more details, refer to the

installation/Instruction sheet.

With bushing

Note - Thomas & Betts hazardous locations fittings with integral seals (STX, STEX, HLT and TC series) are UL and CSA certified only when used

with SC4-KIT or SC65 sealing compounds. No other sealing compounds have been tested, certified or listed.

Cat. No. Description Volume (cubic centimeter)

SC65 Putty type sealing compound (cut-to-length stick)

Cat. No. Description Volume (cubic centimeter)

SC4-KIT Liquid type sealing compound (includes pouch of sealing

compound with integral spout, fiber and damming material).

Use SC4-KIT liquid compound for shielded cables.

Sealing Compounds

U.L. File No. E-82038

CSA File No. LR-23086

Suitable for use on cables with a maximum of four conductors (including ground).

We do not recommend SC65 for use with shielded cables.

Quantity of compound required will vary according to cable conductor fill.

Outside Tray —tray cable must be protected

within conduit and flexible liquidtight metallic

conduit. In this case, the connector bushing is

simply replaced with a ground cone/sealing

ring to terminate the assembly.

Silver Grip®— Liquidtight Fittings for Tray Cable

Approx Compound

Required*

Range Over Conduit Putty / Liquid A B C

Hub Size Jacket (in.) Trade Size SC65/SC4-KIT Throat Dia. Overall Dim.

Cat. No. N.P.T. min. max. (in.) cc (in.) (in.) (in.)

HLT050DATA 1/2 0.250 0.310 1/2 7 0.505 1.870 1.625

HLT050 1/2 0.300 0.400 1/2 7 0.505 1.870 1.625

HLT075 3/4 0.320 0.570 3/4 15 0.707 2.140 2.075

HLT100 1 0.400 0.750 1 23 0.932 2.270 2.290

HLT125 1-1/4 0.625 1.000 1-1/4 45 1.263 2.750 2.840

HLT150 1-1/2 0.780 1.200 1-1/2 68 1.493 3.000 3.275

HLT200 2 1.000 1.560 2 112 1.950 3.200 3.640

4-250TC 2-1/2 1.700 2.200 2-1/2 175 2.250 3.800 4.000

4-300TC 3 2.150 2.700 3 359 2.750 3.860 4.690

4-350TC 3-1/2 2.650 3.230 3-1/2 536 3.280 4.100 5.220

4-400TC 4 3.180 3.790 4 690 3.840 4.000 5.630

† Not UL Listed

* Sealing compound not included with HLT-series. Order separately.

SC65 putty supplied with each TC-series fitting. SC4-Kit liquid sealing compound not approved for use with TC-series.

TC-series is suitable for use with tray cable only and cannot be used with conduit.

Materials

Aluminum: The above listed catalogue numbers relate to aluminum fittings.

Steel: HLT-series is also available in steel. Add the suffix "S" to the catalogue number (example HLT050S).

Certifications

Type HLA. CSA Certified Class I, Division 2, Groups A, B, C and D; Class II, Division 2, Groups E, F and G; Class III,

Division 2, Enclosure Type 4 SL (integral seal). CSA File 23086.

CONFITMRO_EN_ALL.pdf 78 11/28/2011 11:05:32 AM

T&B Conduit Fittings

Flexible Cord and Cable Fittings

Nonmetallic Liquidtight Strain

Relief Fitting—Straight

Trade or Throat Dimensions (in.)

Cat. No. Hub Size Diam. Cord Range A B C

2671 3/8” 0.33 .125-.275 2 29/32 15/32

2690 1/2” 0.33 .125-.275 2-4/16 29/32 19/32

2672 1/2” 0.55 .250-.400 2-19/32 19/32 19/32

2673* 1/2” 0.55 .400-.560 2-19/32 19/32 19/32

2691* 1/2” 0.54 .560-.690 3 1-9/10 19/32

2692* 1/2” 0.54 .660-.780 3 1-9/16 19/32

2693 3/4” 0.55 .250-.400 2-11/16 1-9/32 5/8

2694* 3/4” 0.55 .400-.560 2-11/16 1-9/32 5/8

2674 3/4” 0.79 .560-.690 3 1-9/16 5/8

2675 3/4” 0.79 .660-.780 3 1-9/16 5/8

2696* 3/4” 0.76 .770-.895 3-3/16 1-7/8 5/8

2676 1” 0.98 .660-.780 3-5/16 1-7/8 25/32

2677 1” 0.98 .770-.895 3-5/10 1-7/8 25/32

2678* 1” 0.98 .870-1.020 3-5/10 1-7/8 25/32

2699 1” 0.98 .890-1.090 3-3/10 2-19/32 25/32

2702 1-1/4” 1.25 .890-1.090 3-5/16 1-7/8 25/32

2703 1-1/4” 1.25 1.080-1.280 4 2-19/32 13/16

2704 1-1/4” 1.25 1.270-1.470 4 2-19/32 13/16

2705TB 1-1/2” 1.47 .890-1.150 4-3/16 2-31/32 13/16

2706 1-1/2” 1.47 1.140-1.400 4-5/16 2-31/32 13/16

2707 1-1/2” 1.47 1.390-1.650 4-5/16 2-31/32 13/16

2708 2” 1.89 1.190-1.530 5-3/32 3-1/2 27/32

2709 2” 1.89 1.520-1.860 4-29/32 3-1/2 27/32

2710* 2” 1.89 1.850-2.190 4-29/32 3-1/2 27/32

* Remove sufficient outer covering of cable to permit conductors to pass thru fitting body.

Nonmetallic Liquidtight Strain Relief Fitting—

90° Elbow

Trade or Throat Dimensions (in.)

Cat. No. Hub Size Diam. Cord Range A B C

2680 3/8” .33 .125-.275 .90 1.8 .460

2681 1/2” .55 .250-.400 1.27 2.5 .610

2682* 1/2” .55 .400-.560 1.27 2.5 .610

2683 3/4” .78 .560-.690 1.57 2.8 .610

2684 3/4” .78 .660-.780 1.57 2.8 .610

2688 1” .98 .560-.690 1.89 3.0 .770

2685 1” .98 .660-.780 1.89 3.2 .770

2686 1” .98 .770-.895 1.89 3.2 .770

2687* 1” .98 .870-1.020 1.89 3.2 .770

* Remove sufficient outer covering of cable to permit conductors to pass thru fitting body. 90°

angle, standard size body.

• Weather Stabilized Nylon

• U.L. 94-V2

• Temperature Rating: -34ÞC to +105ÞC

• Meets Coast Guard CG293

90° angle, standard size body.

• Weather Stabilized Nylon

• U.L. 94-V2

• Temperature Rating: -34ÞC to +105ÞC

• Meets Coast Guard CG293

CONFITMRO_EN_ALL.pdf 79 11/28/2011 11:05:33 AM

T&B Conduit Fittings

Portable Cord and Cable Fittings

Strain Relief Fitting

Straight 45° 90°

Cat. Grip Ranger™ Ranger™ T&B Ranger™ T&B Ranger™ Ranger™ T&B

No. Range Steel Aluminum Steel

Malleable Iron

Steel

Malleable Iron

Aluminum Steel

WMG-PC1 .187-.250 2920S 2920AL 2520 4920 2200 4960 4960AL 2267

WMG-PC2 .250-.375 2920S 2920AL 2521 4920 2201 4960 4960AL 2268

WMG-PC3 .375-.500 2921S 2921AL 2522 4921 2202 4961 4961AL 2269

2922S 2922AL 2524 4922 2204 4962 4962AL 2250

WMG-PC4 .500-.625 2932S 2932AL 2534 4932 2209 4972 4972AL 2273

2941S 2941AL 2544 4941 2214 4981 4981AL 2255

2922S 2922AL 2525 4922 2205 4962 4962AL 2251

WMG-PC5 .625-.750 2932S 2932AL 2535 4932 2210 4972 4972AL 2274

2941S 2941AL 2545 4941 2215 4981 4981AL 2256

WMG-PC6 .187-.250 2930S 2930AL 2530 4930 2206 4970 4970AL 2252

WMG-PC7 .250-.375 2930S 2930AL 2531 4930 2207 4970 4970AL 2271

2541

WMG-PC8 .375-.500 2931S 2931AL 2532 4931 2208 4961 4961AL 2272

2940S 2940AL 2542 4940 2213 4980 4980AL 2254

WMG-PC9 .750-.875 2536 2211 2253

2942S 2942AL 2546 4942 2216 4982 4982AL 2275

WMG-PC10 .875-1.000 2547 2217 2276

WMG-PC11 .875-1.000 2548 2218 2257

2558 2220 2277

2548 2218 2257

WMG-PC12 1.000-1.125 2558 2220 2277

2549 2219 2258

2559 2221 2278

WMG-PC13 1.125-1.250 2549 2258 2258 2219

2559 2221 2278

2556 2279 2279 2222

WMG-PC14 1.125-1.250 2563 – 2282

2564 – 2283

WMG-PC15 1.250-1.375 2256 2222 2279

2564 — 2283

WMG-PC16* 1.375-1.500 2557 2223 2280

WMG-PC17* 1.125-1.250 2573 – 2284

2920 Series 2920AL Series

2516 Series

Wiremesh grips support the following Liquidtight

Cord Fittings Series.

Wiremesh Grips for Portable Cord

Application

• Provides high gripping strength for

adequate cable support and strain relief

without damage to the cable sheath

• Compression of a tapered neoprene

bushing, assures the watertight integrity of

the fittings

Cord and Cable Type

• S, SO, SV, ST, STD, SJ, SJO, SJT, SJTO,

SVD

Features

• Prevents severe cord bends and pullouts

• Used in aluminum and/or steel fittings

Material

Wiremesh made of stainless steel. Retaining

rings made of aluminum.

Environment Classification

• Ordinary Locations

Range

.187 – 3.220

How to select proper wiremesh grip:

1. Determine O.D. of portable cord e.g. .200

2. Determine size of knockout or threaded

hub e.g. 1/2"

3. Select Cat. No. of strain relief fitting

e.g. 2520, 2920AL.

4. Match up O.D. with grip range and strain

relief to determine Cat. No. of Wiremesh

Grip (e.g. .200 + 2520 = WMP-PC1)

WMG-PC Series Wiremesh Grips for Portable Cord

T&B Wiremesh grips are ordered separately and fit with your existing inventory of

Ranger™ fittings and liquidtight strain relief fittings. There’s no need to duplicate

inventory.

Strain Relief Fitting

Straight 90°

Cat. Grip T&B T&B

No. Range Steel Steel

WMG-PC18* 1.250-1.375 2573 2284

WMG-PC19* 1.375-1.500 2565 2285

2574

WMG-PC20* 1.500-1.625 2565 2285

2574

WMG-PC21* 1.625-1.750 2575 2286

WMG-PC22* 1.750-1.875 2575 2286

*Replacement Gland Nut Supplied With These

Catalogue Numbers only

CONFITMRO_EN_ALL.pdf 80 11/28/2011 11:05:33 AM

T&B Conduit Fittings

Portable Cord and Cable Fittings

Nonmetallic Cable Glands

Hub Cable Range Length of Thread USE T&B Unit Std. UPC

Cat no. Size Colour in. mm in. mm Locknut cat. no. pkg. pkg. code

NPT Threads

CC-NPT38-B 3/8” BLACK .197 - .394 5-10 0.590 15 CI-1703PL* 50 250 786210-95582

CC-NPT38-G 3/8” GREY .197 - .394 5-10 0.590 15 CI-1703PL* 50 250 786210-07817

CC-NPT12-B 1/2” BLACK .394 - .551 10-14 0.590 15 LN501 50 250 786210-95583

CC-NPT12-G 1/2” GREY .394 - .551 10-14 0.590 15 LN501 50 250 786210-07824

CC-NPT34-B 3/4” BLACK .512 - .709 13-18 0.590 15 LN502 25 100 786210-95584

CC-NPT34-G 3/4” GREY .512 - .709 13-18 0.590 15 LN502 25 100 786210-07853

CC-NPT1-B 1” BLACK .709 - .984 18-25 0.709 18 LN503 20 100 786210-95586

CC-NPT1-G 1” GREY .709 - .984 18-25 0.709 18 LN503 20 100 786210-14682

ISO/Metric Threads

CC-ISO-16-G M16 GREY .197 - .394 5-10 0.394 10 LN-ISO16-G 50 250 786210-21170

CC-ISO-20-G M20 GREY .236 - .473 6-12 0.590 15 LN-ISO20-G 50 250 786210-21173

CC-ISO-25-G M25 GREY .512 - .709 13-18 0.590 15 LN-ISO25-G 25 250 786210-21174

CC-ISO-32-G M32 GREY .709 - .984 18-25 0.590 15 LN-ISO32-G 20 250 786210-21175

CC-ISO-40-G M40 GREY .748 - 1.10 22-32 0.709 18

PG Threads

CC-PG7-G 7 GREY .118 - .256 3-6.5 0.315 8 LN-PG7-G 50 200 786210-21160

CC-PG9-G 9 GREY .157 - .315 4-8 0.315 8 LN-PG9-G 50 200 786210-21162

CC-PG11-G 11 GREY .197 - .394 5-10 0.315 8 LN-PG11-G 25 100 786210-21163

CC-PG135-G 13-1/2 GREY .236 - .473 6-12 0.354 9 LN-PG135-G 25 100 786210-21164

CC-PG16-G 16 GREY .394 - .551 10-14 0.394 10 LN-PG16-G 25 100 786210-21165

CC-PG21-G 21 GREY .512 - .709 13-18 0.433 11 LN-PG21-G 10 50 786210-21166

CC-PG29-G 29 GREY .709 - .984 18-25 0.433 11 LN-PG29-G 10 50 786210-21167

CC-PG36-G 36 GREY .867 - 1.26 22-32 0.512 13 LN-PG36-G 10 50 786210-21168

Nonmetallic Cable Glands — Low Profile for Tight Spots

T&B Nylon Cable Glands have a sturdy cable sealing mechanism which results in

superior strain relief. The compact size ensures quick and easy installation in

cramped spaces. The nonmetallic construction provides excellent corrosion,

chemical and impact resistance. The glands have long threads and locknuts are

available.

• Halogen free

• Flame retardant material rated UL 94-V0

• Rated IP 68 5 BAR, suitable for NEMA 4 enclosures

• UL Listed, CSA listed for certain ranges of cable

• Working Temperatures: -30°C (-86°F) to +80°C (176°F) Continuous, 150°C

(276°F) Intermittent

• Meets VDE ratings

Sturdy Nylon 6 for strong, lightweight construction.

Gray colour shown, also available in black.

* Not CSA Certified.

81-E.pdf 1 6/18/2012 2:02:34 PM

T&B Conduit Fittings

Portable Cord and Cable Fittings

Metric PG-to-N.P.T. Thread Adapters

N.P.T. Thread

Cat. No. Thread (mating) (at housing)

PG11-38 3/8” PG11

PG16-50 1/2” PG16

PG21-75 3/4” PG21

PG29-100 1” PG29

PG29-125 1-1/4” PG29

PG36-125 1-1/4” PG36

PG36-150 1-1/2” PG36

Metric Two-Screw Clamp Fittings

Cable O.D. (in.) Thread

Cat. No. Min. Max. (at housing)

CC11-38 .400” .470” PG11

CC11-38P* .250” .325” PG11

CC135-50 .400” .535” PG13.5

CC16-50 .455” .625” PG16

CC21-75 .513” .815” PG21

CC29-100 .800” .175” PG291

CC36-125 1.050” .450” PG361

CC42-150 1.500” .800” PG421

* Plastic

Metric Cord Grip Fittings

Cable O.D. (in.) Thread

Cat. No. Min. Max. (at housing)

CG11-38 .200” .470” PG11

CG11-38P* .325” .340” PG11

CG135-50 .285” .545” PG13.5

CG16-50 .285” .625” PG16

CG21-75 .395” .790” PG21

CG29-100 .780” .060” PG291

CG36-125 .960” .375” PG361

CG42-150 1.630” .650” PG421

* Plastic

Conduit Entry Blind Plug

Thread

Cat. No. (at housing)

CXP722 PG13.5

CXP723 PG16

CXP724 PG21

CXP725 PG29

CXP726 PG36

CXP727 PG42

Supplied standard with all hoods and bases.

Special sizes/hood combinations available.

Style may vary depending on size.

Standard European style — can be specified/

supplied with hoods and bases.

CONFITMRO_EN_ALL.pdf 82 11/28/2011 11:05:33 AM

T&B Conduit Fittings

Service Entrance Cable Fittings

Suggested Specifications for Service Entrance Fittings

Series 4175

Pipe Strap (EMT)

Series 1275/1275AL Pipe Strap

(Rigid Metal Conduit & I.M.C.)

Series 1350/1350AL Pipe Spacer

(Rigid Metal Conduit I.M.C. & EMT)

Series 3870

Bonding & Grounding Bushing—Insulated

Series 106

Bonding Locknut

• All service fittings shall be approved for

the purpose by a nationally recognized

testing laboratory, inspection agency, or

product evaluation organization.

• Where service raceway consists of a

rigid metal conduit, intermediate

metal conduit, electrical metallic

tubing or where service entrance

cable is used as service conductors a

suitable raintight service head

conforming to Federal Standard

W-C-586 shall be provided.

• Service raceway shall be securely

fastened in place to the supporting

surface at intervals as specified by the

Code using suitable straps and

spacers; straps and spacers shall be of

malleable iron or steel construction, hot

dipped galvanized or electro zinc

plated conforming to Canadian

Standards Association Standard

C22.2 No. 18.4 and as manufactured

by Thomas & Betts: series 1275 or

4175 straps and series 1350 spacers;

aluminum straps or spacers such as

series 1275AL and series 1350AL

may be substituted when installed in

environmental conditions that are

more than normally corrosive.

• For grounding and bonding of service

raceway, end of raceway or the

terminating fitting shall be equipped

with bonding locknuts and insulated

metallic grounding and bonding

bushing as required.

Bonding locknuts shall be of hardened

steel or malleable iron construction,

electro zinc plated, and provided with

hardened bonding screws as

manufactured by Thomas & Betts,

series 106 bonding locknuts.

Insulated metallic grounding and

bonding

bushing shall be of malleable

iron/steel construction, electro zinc

plated and assembled with an

insulator listed or certified for

150°C/302°F service as manufactured

by Thomas & Betts, series 3870.

CONFITMRO_EN_ALL.pdf 83 11/28/2011 11:05:33 AM

T&B Conduit Fittings

Service Entrance Cable Fittings

• Where service entrance cable is used

as overhead service conductors and

code requires use of a service head,

entrance caps shall be installed; caps

shall be cast metal type of suitable

ferrous or non ferrous metal equipped

with thermoset insulators and proper

knockout openings; when installed

with proper drip loop, caps must

assure raintight conditions.

• Terminating fittings for service entrance

cable (Type SE or USE) or underground

feeder and branch—circuit cable (Type

UF) in locations where exposed to

intermittent or constant moisture or in

dry locations and subjected to

mechanical strain shall be of watertight

strain relief type as manufactured by

Thomas & Betts, series 2111 or 2116;

fittings shall be constructed of ferrous

or non ferrous metal and equipped

with taper-threaded hub, beveled

moisture resistant/oil resistant

synthetic rubber bushing.

In dry locations, nylon insulated two

screw type fittings of malleable

iron/steel construction, electro zinc

plated inside and outside including

threads, such as series 3302M

manufactured by Thomas & Betts may

be substituted.

• Where service entrance cable is

terminated into a threadless opening

using hub type fittings, a gasket shall

be provided between the outside of

box or enclosure and fitting shoulder;

gasket shall be of moisture resistant/ oil

resistant synthetic rubber type

adequately protected by and

permanently retained to a metallic

retainer as manufactured by Thomas &

Betts, series 5262 or 5302.

• Service entrance cable shall be

adequately supported at intervals

enumerated in code using cable straps

conforming to requirements of CSA

Standard C22.2 No.18.4; cable straps

shall be of malleable iron/steel

construction, hot dipped galvanized or

electro zinc plated as manufactured by

Thomas & Betts, series 1341.

• At the point where the service cable

enters the building, a suitable sill

plate shall be provided; sill/wall plate

shall be sealed to assure raintight

conditions.

Series 2111

Service Entrance Cable Fitting

Series 2116

Underground Feeder Cable Fitting

Series 3302M

Two Screw Fitting (Insulated)

Series 5262, 5302

Sealing Gasket

Series 1341

Cable Strap

Suggested Specifications for Service Entrance Fittings—continued

CONFITMRO_EN_ALL.pdf 84 11/28/2011 11:05:34 AM

T&B Conduit Fittings

Service Entrance Cable Fittings

Application

• To connect service entrance cables

to a meter box or an enclosure.

Standard Material/Finish

Body Zinc Die Cast/As cast

Gland Steel/Electro Zinc

Plated & Chromate

Coated

Retaining Ring Stainless

Steel/Passivated

Bushing Neoprene/As molded

Range

• Oval (Flat) Cable Size

0.260 x 0.500 thru 1.062 x 1.765

• Type USE Cable Size

3 #12 thru 3-4/0 AWG Conductors

• Hub Size

1¼2”thru 2”NPT (taper pipe threads)

Features

• Neoprene bushing, resists oil and

water; grips cable the full length of

the bushing providing adequate

strain relief without damaging outer

jacket (A).

• Taper-threaded body (B).

• Stainless steel retaining ring protects

cable jacket against abrasion;

reduces installing torque effort (C).

• Rugged ribbed steel gland

construction (D).

• Suitable for Type USE I75, USE I90

and USE B90 (CEC Table 19) Service

Entrance Cable.

Listing/Certification

CEC Rule 6-300 (1) add (b) use

underground service entrance with

mechanical protection as per CEC

Rule 12-012

Conformity

U.L.514B, NEMA FB-1, Federal

Standard H-28 (Threads),

NFPA70-2009 (ANSI)

CSA C22.2 No. 18.3

Application

• To connect underground feeder

cables to a box or an enclosure.

Standard Material/Finish

Body Zinc Die Cast/As cast

Gland Steel/Electro Zinc

Plated & Chromate

Coated

Retaining Ring Stainless Steel/

Passivated

Bushing Neoprene/As molded

Range

• Oval (Flat) Cable Size

0.235 x 0.500 thru 0.260 x 0.740

• Hub Size 1/2” thru 1” NPT (tapered

pipe threads)

Features

• Neoprene bushing resists oil and

water; grips cable the full length of

the bushing providing adequate strain

relief without damaging outer jacket

(A).

• Taper-threaded body (B).

• Stainless steel retaining ring protects

cable jacket against abrasion;

reduces installing torque effort (C).

• Rugged ribbed steel gland

construction (D).

Listing/Certification

CEC Rule 30-1004 (d) Wiring method,

underground, where deviation has

been allowed for permanent outdoor

floodlighting installation.

Conformity

U.L.514B, NEMA FB-1, Federal

Standard H-28 (Threads),

NFPA70-2009 (ANSI)

CSA C22.2 No. 18.3

Service Entrance Cable Fittings

(Type SE/Type Use)

2111 Series

2116 Series

Underground Feeder Cable Fittings

(C)

(D)

(C)

(B)

(A)

(B)

(A)

CONFITMRO_EN_ALL.pdf 85 11/28/2011 11:05:34 AM

T&B Conduit Fittings

Service Entrance Cable Fittings

Underground Liquidtight Feeder Cable Fittings

Dimensions (in.)

Hub Cable A B C D E F G H

Cat. No. Size Opening min. max. min. max

2116* 1/2” .235 x .500 1-11/16 5/8 1 .060 .235 .350 .500 9/16 1-1/8 1-1/8

2237 3/4” .230 x .430 1-9/16 9/16 1-7/32 .080 .230 .320 .430 13/16 1-3/8 1-3/8

2238 3/4” .235 x .465 1-9/16 9/16 1-7/32 .050 .235 .340 .465 13/16 1-3/8 1-3/8

2239 3/4” .240 x .685 1-9/16 9/16 1-7/32 .060 .240 .500 .685 13/16 1-3/8 1-3/8

* Not CSA Certified.

Watertight Fittings for Oval Cables

Hub Dimensions (in.) Oval Cable Range

Cat. No. Size A B C D E max. min.

2111 1/2” 1-3/4 1-1/4 5/8 1-3/8 1-3/8 .420 x .560 .380 x .520

2232 3/4” .385 x .600 .260 x .500

2233 3/4” 1-11/16 1-1/4 9/16 1-3/8 1-3/8 .500 x .750 .375 x .625

2234 3/4” .555 x .800 .490 x .675

2432 1” .385 x .600 .260 x .500

2433 1” 1-11/16 1-1/4 9/16 1-3/8 1-3/4 .500 x .750 .375 x .625

2434 1” .555 x .800 .430 x .675

2438 1” 1-3/4 1-1/2 25/32 1-11/16 1-3/4 .565 x .855 .440 x .730

2439 1” .635 x .975 .510 x .850

2442 1-1/4” .635 x .975 .510 x .850

2443 1-1/4” 2-1/16 1-15/16 5/8 2-1/16 2-1/8 .640 x 1.050 .490 x .900

2446 1-1/4” .750 x 1.150 .565 x .965

2454 1-1/2” 2-1/4 2-1/8 11/16 2-5/16 2-5/16 .840 x 1.275 .655 x 1.090

2447 1-1/2” .880 x 1.425 .695 x 1.240

2448 2” .968 x 1.500 .790 x 1.390

2449 2” 2-3/8 2-5/8 11/16 2-3/4 2-13/32 1.062 x 1.765 .850 x 1.550

2450 2” 1.820 x 1.190 1.700 x 1.050

Oil and water resistant neoprene bushing is

especially designed for sealing around

underground feeder cable. Stainless steel

retaining ring provides a bearing surface for the

glandnut and eliminates cable twist. Ribbed

glandnut is strong and easily tightened with a

wrench to make a connection of high strength.

A design with two tapers inside the body—a

slow one and a fast one—permits the stocking

of fewer fittings for varied cable sizes and

allows maximum take-up. The tapered neoprene

bushings are resistant to oil, sunlight, and water.

Hex gland and body take the same wrench

opening and a stainless steel slip ring prevents

cable from twisting as gland ring is being

tightened. Threads on the body are tapered for

watersealing.

CONFITMRO_EN_ALL.pdf 86 11/28/2011 11:05:34 AM

T&B Conduit Fittings

Service Entrance Cable Fittings

Cable Straps

Dimensions (in.)

Cat. No. Wire Size A B

1341 2-#10 5/8 1-1/8

1344 3-#6 or 3-#8 5/8 1-15/16

1345* 3-#4 or 3-#2 13/16 1-59/64

1346 3-1/0 3/4 2-7/16

1347 3-4/0 3/4 2-25/32

* Steel, hot dipped galvanized.

Nylon UF Cable Fittings for Corrosive Environments

Dimensions (in.)

Hub UF Cable Range A B C

Cat. No. Size max. min. max. ± .060 ± .060

2827 1/2” .550 x .280 .400 x .190 2.60 1.270 .600

2828 3/4” .675 x .280 .525 x .190 3.00 1.570 .620

2829 3/4” .775 x .280 .625 x .190 3.00 1.570 .620

• Tapered threaded hub.

• Liquidtight and dust-tight; hand tightens—

no tools required.

• Corrosive and weather resistant nylon for

outdoor and indoor applications.

Each strap takes a wide range of sizes because

of the rocking action of the foot. Hole is for 1¼4”

screw. Malleable iron, hot dipped galvanized

construction.

CONFITMRO_EN_ALL.pdf 87 11/28/2011 11:05:34 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Please Note

The excerpts and other material herein, whether relating to the Canadian

Electrical Code 2009 Part I, the Underwriters Laboratories, Inc. listing,

to industry practice or otherwise, is not intended to provide all relevant

information required for use and installation. Reference to original or primary

source material and data is mandatory before any application or use is made of

the product.

Specifications — Liquidtight Flexible Metal Conduit

Ref. CEC Rule 12-1300

Liquidtight flexible metal conduit is a

raceway of circular cross section having

an outer liquidtight nonmetallic, sunlight

resistant jacket over a flexible metal core.

Liquidtight flexible metal conduit is

permitted to be used for exposed or

concealed work, in dry, damp or wet

locations indoors and outdoors. With the

exception of Class I Division I locations,

liquidtight flexible metal conduit is

considered an acceptable wiring method

hazardous locations Class 1 Division 2

(CEC Rule J18-152(6).

Liquidtight flexible metal conduit is

not permitted where subjected to mecha-

nical injury. The conduit is not permitted to

be used underground or embedded in

cinder fill or concrete. It cannot be used as

a general purpose raceway.

Use of liquidtight conduit is not

permitted where any combination of

ambient or conductor temperature will

produce temperature in excess of that for

which the jacket is rated or in locations

where flexing at low temperature will

injure jacket. Liquidtight flexible metal

conduit is not permitted for conductors

over 600 volts.

Liquidtight flexible conduit is available in

3/8” through 6” trade size. Conduit is

constructed with galvanized steel or

aluminum core, regular or extra flex. Outer

jacket is available for a variety

of applications, e.g. oil resistant where

exposed to cutting oils and for service

temperature ranging from -50°C to

150°C.

Listed and certified conduits are

constructed of galvanized steel core

and thermoplastic jacket rated for

maximum service temperature of 60°C

and suitable for exposure to mineral oils

but not to gasoline and similar solvents.

Conduit is required to be supported

adequately, and bending is restricted to

360 degrees total.

Please refer to the following for further

details and complete information:

1. U.L. 360…Safety Standards for

Liquidtight Flexible Steel Conduit

2. U.L. 514, Safety Standards for

Outlet Boxes and Fittings

3. W-F-406…Federal Specification:

Fittings for Cable, Power, Electrical

and Conduit, Metal, Flexible

4. NEMA FB-1…Standards Publication:

Fittings and Supports for Conduit and

Cable Assemblies

5. EMP-1…JIC Electrical Standards

for Mass Production Equipment

6. EGP-1…JIC Electrical Standards for

General Purpose Machine Tools

7. CEC Section 12-1300…Wiring

Methods (Liquidtight Metal Conduit)

8. CSA C22.2 No. 56…Safety

Standard for Flexible Metallic

Conduit and Liquidtight Flexible

Metal Conduit

9. CSA C22.2 No. 18…Safety

Standards for Outlet Boxes,

Conduit Boxes and Fittings

CONFITMRO_EN_ALL.pdf 88 11/28/2011 11:05:34 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Suggested Specifications for Liquidtight Flexible Metal

Conduit Fittings

• Liquidtight Flexible Metal conduit

used shall be of the type with

galvanized steel core inside and

outside and outer thermoplastic

jacket suitable for the ambient

environmental conditions. Jacket shall

be positively locked to core to

prevent sleeving. Where used as an

equipment grounding conductor, the

conduit shall conform to applicable

standards U.L. 360/CSA C22.2 No.

56.

• Flexible conduit when installed shall

have sufficient slack to avoid sharp

flexing and straining due to vibration

and thermal expansion/constriction.

Conduit shall be installed in such a

manner that liquids will tend to run off

the surface instead of draining

toward the fittings.

• Where liquidtight flexible metal

conduit terminates into a threaded

or threadless opening, the conduit

shall be assembled with approved

liquidtight fittings. Fittings used shall

be reusable type of malleable

iron/steel construction, electro-zinc

plated inside and outside, furnished

with nylon insulated throat and taper

threaded hub as manufactured by

Thomas & Betts, series 5331.

Approved fittings installed shall be:

(1) Designed to prevent sleeving,

assure plastic (raceway jacket)

to plastic (gasket) seal.

(2) Equipped with grounding device

to assure ground continuity

irrespective of raceway core

construction. Grounding device

if inserted into raceway and

directly in contact with conductors

shall have rolled over edges for

sizes under 5 inches.

At the point of flexing (i.e. where

raceway leaves fitting) the

thermoplastic raceway jacket shall

not be permitted to be in direct

contact with metal.

• Where liquidtight flexible metal

conduit is terminated into a

threadless opening using a threaded

hub fitting such as Thomas & Betts

series 5331, a suitable moisture

resistant/oil resistant synthetic rubber

gasket such as Thomas & Betts

series 5262 shall be provided

between the outside of box or

enclosure and fitting shoulder. Gasket

shall be adequately protected by and

permanently bonded to a metallic

retainer.

• Where liquidtight flexible metallic

raceway is installed in outdoor or

indoor locations and is exposed to

environmental conditions that are

more than normally corrosive to

exposed surfaces, PVC coated

liquidtight flexible metal conduit

fittings such as series 3321

manufactured by Thomas & Betts

shall be used. Fittings shall be coated

with a nominal thickness of .040 PVC

and must meet the general

requirements for liquidtight flexible

metal conduit fittings indicated

above.

• Liquidtight fittings required to couple

threaded end of a fitting or pipe where

rotation of fitting or pipe is limited or

restricted shall be reusable type of

malleable iron/steel construction,

electro-zinc plated inside /outside with

taper threaded hub as manufactured by

Thomas & Betts, series 41. Fittings

shall be equipped with a moisture

resistant/oil resistant synthetic

rubber gasket. Metal to metal seal or

metal to thermoplastic seal for this

application shall be considered

unacceptable.

Series 5331; Series 5231AL

Liquidtight Flexible Metal

Conduit Fittings

Series 3321

PVC Coated Liquidtight Flexible

Metal Conduit Fittings

Series 41

Liquidtight Union

5331GR Series

External Bonding

Series 5262

Sealing Gasket

Stainless

Steel

Retainer

Resilient Seal

Resilient Sealing

Material Locked

in Steel Retainer

CONFITMRO_EN_ALL.pdf 89 11/28/2011 11:05:34 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Specifications

Application

• Used where flexible metal raceway

is installed in outdoor or indoor

locations where exposed to

continuous or intermittent moisture.

• To positively bond conduit to box

or enclosure.

Features

• Ability to install quickly with low

torque effort.

•Ground cone design offers following

advantages:

(1) Compresses metallic convolutions;

provides high quality ground

contact with low impedance and

high raceway holding power (A).

(2) Single helical thread on ground

cone is easy to install without

cross threading; accepts

variations in raceway diameters

and convolution pitch (B).

(3) Rolled over edge protects

conductors (C).

Sealing ring design has following

exclusive features:

(1) Grips and seals at leading and

trailing edge—will not abrade

raceway jacket (D).

(2) Provided with grooves on inside

diameter for anti-sleeving (E).

(3) Shoulders on both ends for extra

sealing (F).

(4) Symmetrical shape assures

foolproof assembly.

• Can be disconnected and reused

• Watertight/oiltight installation at box or

enclosure termination is assured by:

(1) External taper thread hub on 5331

series and use of sealing gasket

5262 series (G).

(2) Captive sealing ‘O’ ring on 5361

series (H).

(3) Taper tapped hole on 5271series.

• Suitable for use in Class I Division 2,

Class II Division 1 and 2 and Class III

Division 1 and 2 Hazardous Locations

per CEC Section 18.

Class I, Zone 2, CEC Rule 18-152 (6)

Class I, Div. 2, CEC Rule J18-152 (6)

Class II, Div. 1 CEC Rule 18-202 (4) (b)

Class II, Div. 2, CEC Rule 18-252 (4)

Class III, Div.1 CEC Rule 18-302 (4)

Class III, Div. 2 CEC Rule 18-352

• CEC Rule 12-1306 stipulates “a

separate bonding conductor shall be

installed in liquidtight flexible conduit in

accordance with section 10”.

• 1/2” and 1-1/4” sizes Laboratory

tested to carry ground fault current of

up to 1000 amps RMS with duration

of fault current 3 cycles.

• Conforms with JIC requirements.

• Available with imperial, I.S.O. and PG

threaded hub.

Standard Material

5331-5361-5271 Series

Body, Gland, Locknut and Ground

Cones: All steel or malleable iron.

Sealing Ring and Insulator:

All thermoplastic rated min. -20ºc

max. 105°C

Sealing Gasket: Stainless Steel and

Buna N

5231 AL Series

All Copper-free Aluminum

(non-insulated)

Standard Finish

5331-5361-5271 Series

Electro Zinc Plated and Chromate

Coated

5231 AL Series

Copper-free Aluminum

Range

• 5331 Series 3/8” thru 6” conduit

• 5341 Series 3/8” thru 4” conduit

• 5351 Series 3/8” thru 4” conduit

• 5361 Series 3/8” thru 4” conduit

• 5271 Series 3/8” thru 1-1/4”

conduit

• 5231 AL Series 3/8” thru 4” conduit

All hubs provided with taper pipe

threads (NPT).

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NEMA FB-1

NFPA 70-2008 (ANSI)

JIC EGP1, JIC EMP1

Federal Specification W-F-406

Federal standard H-28 (Threads)

5331 Series

5231 AL Series

5361 Series

Chase Style

5361 Series

5271 Series

5341 Series…

same as 5331, except 45° Fittings

5351 Series…

same as 5331, except 90° Fittings

Predetermined

Compression

CONFITMRO_EN_ALL.pdf 90 11/28/2011 11:05:35 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

T&B HT-Series Liquidtight Fittings are available

straight, 45°, and 90°.

High Temperature Flexible Metal Liquidtight Fittings

Suggested Specification

Where Liquidtight flexible metal fittings are required in high temperature environments

up to 150°C:

• Fitting’s body, gland, locknut and ground cone shall be constructed from steel or

malleable iron, electro-zinc plated and chromate coated for corrosion protection.

• Fitting’s sealing ring and throat insulator will be molded from high temperature nylon

suitable for temperatures up to 150°C and a minimum UL flammability

rating of UL94-V2.

• The fitting shall be constructed to accept high temperature flexible metal

liquidtight conduit rated to 150°C (works with our ATX Series conduit, p. 135).

• The fitting shall have a plastic throat insulator to protect conductors.

• The fitting shall have a steel ground cone to:

- provide high quality ground contact

-single helical thread for easy installation into conduit

-rolled over edge to protect conductors

• The fitting shall have a plastic sealing ring to:

-grip and seal at leading and trailing edge (double bevel up to 2”) of conduit jacket

-provide a watertight/oiltight seal

• The fittings shall be capable to terminate the conduit in either a threaded or

threadless opening.

• For applications where termination into a threaded opening is required the

fitting shall have external tapered NPT threads.

• For applications where termination into a threadless opening is required use an

acceptable sealing ring.

• Fittings shall conform to UL 514B.

• Accepted Manufacturers: Thomas & Betts — 5331-HT straight series,

5341-HT 45° series, 5351-HT 90° series; 5262 sealing ring series.

Straight Liquidtight Fittings

Conduit Dimensions (in.)

Cat. No. Size (in.) A B C

5331-HT 3/8 1-5/32 1-1/2 9/16

5332-HT 1/2 1-3/8 1-9/16 9/16

5333-HT 3/4 1-21/32 1-5/8 9/16

5334-HT 1 1-7/8 2-1/16 3/4

5335-HT 1-1/4 2-9/32 2-1/2 13/16

5336-HT 1-1/2 2-22/32 2-11/16 13/16

5337-HT 2 3-1/4 3-1/16 7/8

5338-HT 2-1/2 3-3/4 4-1/8 1

5339-HT 3 4-1/2 4-1/4 1

5340-HT 4 5-1/2 4-1/2 1-1/8

45° Liquidtight Fittings

Conduit Dimensions (in.)

Cat. No. Size (in.) A B C

5341-HT 3/8 1-5/32 1-9/16 9/16

5342-HT 1/2 1-3/8 1-7/8 9/16

5343-HT 3/4 1-21/32 2-1/8 9/16

5344-HT 1 1-7/8 2-1/4 3/4

5345-HT 1-1/4 2-9/32 2-3/4 13/16

5346-HT 1-1/2 2-22/32 2-3/8 13/16

5347-HT 2 3-1/4 3-7/8 7/8

90° Liquidtight Fittings

Conduit Dimensions (in.)

Cat. No. Size (in.) A B C

5351-HT 3/8 1-5/32 1-3/8 9/16

5352-HT 1/2 1-3/8 1-9/16 9/16

5353-HT 3/4 1-21/32 1-3/4 9/16

5354-HT 1 1-7/8 2-3/16 3/4

5355-HT 1-1/4 2-9/32 2-3/4 13/16

5356-HT 1-1/2 2-22/322-15/16 13/16

5357-HT 2 3-1/4 3-7/16 7/8

Please note: There is no CSA and UL Standards applicable for High Temperature Fittings or Conduits.

Therefore neither HT Fittings nor HT Conduit bear these Certifications/Listings.

91-e.pdf 1 5/29/2012 9:24:15 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

For Control and Power Cable Applications

Hub Conduit Dimensions (in.)

Cat. No. Size Size A B C

5229* 1/4” 1/4 27/32 1-3/8 15/32

5330* 3/8” 5/16 63/64 1-3/8 15/32

* U.L. and CSA not applicable.

Straight Fittings

Cat. No. Conduit Dimensions (in.)

Insulated Aluminum‡Noninsulated Size A B C

5331**



5231AL 5231 3/8 1-5/32 1-1/2 9/16

5332



5232AL 5232 1/2 1-3/8 1-9/16 9/16

5333



5233AL 5233 3/4 1-21/32 1-5/8 9/16

5334



5234AL 5234 1 1-7/8 2-1/16 3/4

5335



5235AL 5235 1-1/4 29/32 2-1/2 13/16

5336+ 5236AL 5236 1-1/2 2-23/32 2-11/16 13/16

5337+ 5237AL 5237 2 3-1/4 3-1/16 7/8

5338+ 5238AL 5238 2-1/2 3-3/4 4-1/8 1

5339+ 5239AL 5239 3 4-1/2 4-1/4 1

5340+ 5240AL 5240 4 5-1/2 4-1/2 1-1/8

5385*+ —5285* 5 8-3/4 7 1-7/8

5386*+ — — 6 8-3/4 8-1/2 2

Suitable for hazardous locations use in CEC Rule 18-152 (6) Class I, Zone 2;

CEC Rule J18-152 (6) Class I, Division 2; CEC Rule 18-202 (4) Class II, Division 1;

CEC Rule 18-252 (4) Class II, Division 1

** 3/8” Conduit Fitting has 1/2” hub.

U.L. Listed liquidtight; and CSA Certified watertight.

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

* Not CSA Certified.



Steel

Malleable Iron

45° Angle Fittings*

Cat. No. Conduit Dimensions (in.)

Insulated Noninsulated Size A B C

5341** 5241 3/8 1-5/32 1-9/16 9/16

5342 5242 1/2 1-3/8 1-7/8 9/16

5343 5243 3/4 1-21/32 2-1/8 9/16

5344 5244 1 1-7/8 2-1/4 3/4

5345 5245 1-1/4 29/32 2-3/4 1-3/16

5346 5246 1-1/2 2-23/32 3-3/8 1-3/16

5347 5247 2 3-1/4 3-7/8 7/8

5348 5248 2-1/2 3-3/4 4-1/4 1

5349 5249 3 4-1/2 4-1/4 1

5350 5250 4 5-1/2 4-5/8 1-1/8

* Suitable for hazardous locations use CEC Rule 18-152 (6) Class I, Zone 2;

CEC Rule J18-152 (6) Class I, Division 2; CEC Rule 18-202 (4) Class II, Division 1;

CEC Rule 18-252 (4) Class II, Division 1

** 3/8” Conduit Fitting has 1/2” hub.

U.L. Listed liquidtight; and CSA Certified watertight.

For Dura-Plate™ finish, add prefix 040- to Cat. No. Consult Customer Service for details.

For Wiremesh Grips refer to page 80.

Steel, malleable iron, or aluminum tapered hub

threads. With safe-edge ground thru 4” cone and

double bevel sealing ring (through 2”).

Malleable iron, tapered hub threads. With safe-

edge ground cone and double bevel sealing ring

(through 2”).

CONFITMRO_EN_ALL.pdf 92 11/28/2011 11:05:35 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

90° Angle Fittings

Cat. No. Hub Conduit Dimensions (in.)

Insulated Noninsulated Aluminum Size Size A B C

5351 5251 5251AL 1/2” 3/8” 1-5/32 1-3/8 9/16

5352 5252 5252AL 1/2” 1/2” 1-3/8 1-9/16 9/16

5353 5253 5253AL 3/4” 3/4” 1-21/32 1-3/4 9/16

5354 5254 5254AL 1” 1” 1-7/8 2-3/16 3/4

5355 5255 5255AL 1-1/4” 1-1/4” 29/32 2-3/4 13/16

5356 5256 5256AL 1-1/2” 1-1/2” 2-23/32 2-15/16 13/16

5357 5257 5257AL 2” 2” 3-1/4 3-7/16 7/8

5358 5258 5258AL* 2-1/2” 2-1/2” 3-3/4 8-7/8 1

5359 5259 — 3” 3” 4-1/2 10-1/4 1

5360 5260 — 4” 4” 5-1/2 12-5/8 1-1/8

Suitable for hazardous locations use in CEC Rule 18-152 (6) Class I, Zone 2;

CEC Rule J18-152 (6) Class I, Division 2; CEC Rule 18-202 (4) Class II, Division 1;

CEC Rule 18-252 (4) Class II, Division 2.

U.L. Listed liquidtight; and CSA Certified watertight.

* Not CSA Certified.

Wiremesh Grips for Liquidtight Fittings

Conduit Liquidtight Fittings 90°

Cat. No. Size Straight 45° 90° Chase Chase Adapter

WMG-LT1 3/8” 5331 5341 5351 5361 5371 5271

WMG-LT2 1/2” 5332 5342 5352 5362 5372 5272

WMG-LT3 3/4” 5333 5343 5353 5363 5373 5273

WMG-LT4 1” 5334 5344 5354 5364 5374 5274

WMG-LT5 1-1/4” 5335 5345 5355 5365 — 5275

WMG-LT6 1-1/2” 5336 5346 5356 5366 — 5276

WMG-LT7 2” 5337 5347 5357 5367 — 5277

WMG-LT8 2-1/2” 5338 5348 5358 5368 — 5278

WMG-LT9 3” 5339 5349 5359 5369 — 5279

WMG-LT10 4” 5340 5350 5360 5370 — 5282

Order wiremesh grip separately: no need to duplicate inventory.

Prevents severe conduit bends and pullout.

CONFITMRO_EN_ALL.pdf 93 11/28/2011 11:05:35 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Liquidtight Adapter

To Connect Liquidtight to Threaded Rigid Conduit

Conduit Size Dimensions (in.) Std.

Cat. No. (in.) A B C Pkg.

5271 3/8 1-5/32 1-9/16 1-3/8 50

5272 1/2 1-3/8 1-11/16 1-3/8 50

5273 3/4 1-21/32 1-3/4 1-3/8 50

5274 1 1-7/8 2-1/8 1-3/8 25

5275 1-1/4 2-9/32 2-1/2 1-3/8 25

5276 1-1/2 2-3/4 2-11/16 1-3/8 10

With SAFE-EDGE™ ground cone and double bevel sealing ring (through 2”).

Suitable for hazardous locations use in CEC Rule 18-152 (6) Class I, Zone 2;

CEC Rule J18-152 (6) Class I, Division 2; CEC Rule 18-202 (4) Class II, Division 1;

CEC Rule 18-252 (4) Class II, Division 2.

Nylon Insulated CHASE®Fittings

Steel or Malleable Iron

Conduit Size Dimensions (in.) Std.

Cat. No. (in.) A B C Pkg.

5361 3/8 1-3/32 1-3/8 1/8 100

5362 1/2 1-3/8 1-3/8 3/16 100

5363 3/4 1-11/16 1-5/8 1/4 50

5364 1 2-1/32 2-1/16 1/4 25

5365 1-1/4 2-3/8 2-3/8 5/16 25

5366 1-1/2 2-15/16 2-3/4 3/8 10

5367 2 2-9/16 3 3/8 5

5368 2-1/2 4-3/8 3-15/16 7/16 5

5369 3 5-1/8 4-1/8 1/2 5

5370 4 5-1/8 4-3/8 1/2 5

With SAFE-EDGE™ ground cone and double bevel sealing ring (through 2”).

Note: UL Listed Liquidtight; and CSA Certified Watertight.

Suitable for hazardous locations use in CEC Rule 18-156 (6) Class I, Zone 2;

CEC Rule J18-156 (3) Class I, Division 2; CEC Rule 18-202 (4) Class II, Division 1;

CEC Rule 18-252 (4) Class II, Division 2.

CONFITMRO_EN_ALL.pdf 94 11/28/2011 11:05:36 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Specifications — External Bonding

Application

• Used where external bonding jumper

is required around liquidtight flexible

metal conduit.

• To positively bond conduit to box

or enclosure.

• Used where flexible raceway is

installed in outdoor or indoor locations

where exposed to continuous or

intermittent moisture.

Features

• Designed with provision to install

bonding jumper in several positions.

• Designed to accept mechanical or

compression lug.

• Ability to install quickly with low

torque effort.

(i) Compresses metallic

convolutions; assures ground

contact with low impedance and

high raceway holding power (A).

(ii) Single helical thread on ground

cone is easy to install without

cross threading; accepts

variations in raceway diameters

and

convolution pitch (B).

(iii) Rolled over edge protects

conductors (C).

• Sealing ring design has following

exclusive features:

(i) Grips and seals at leading and

trailing edge—will not abrade

raceway jacket (D).

(ii) Provided with grooves on inside

diameter for anti-sleeving (E).

(iii) Shoulders on both ends for extra

sealing (F).

(iv) Symmetrical shape assures

foolproof assembly.

• Can be disconnected and reused.

• Watertight/oiltight installation at box or

enclosure termination is assured by:

1. External taper thread hub on

5331GR series and use of

sealing gasket 5262 series (G).

2. Taper tapped hole on 5271 series.

• Suitable for use in Class I Division 2,

Class II Division 1 & 2 and Class III

Division 1 & 2 Hazardous Locations

per CEC Section 18.

• Conforms with JIC requirements.

• CEC Rule 12-1306 stipulates “a

separate bonding conductor shall be

installed in liquidtight flexible conduit in

accordance with section 10”.

• CEC Rule 10-618 (3) “The armour of

flexible metal conduit and liquidtight

flexible metal conduit shall not be

considered as fulfilling the

requirements of a bonding conductor

for the purposes of this rule, and a

separate bonding conductor shall

be run within the conduit”.

Standard Material

Lugs: High conductivity copper

(for copper conductor only).

Body, Gland, Locknut & Ground

Cones: All steel or malleable iron.

Sealing Ring and Insulator:

All thermoplastic

Sealing Gasket: Stainless Steel & Buna N

Strap: Steel

Standard Finish

All Electro Zinc Plated and Chromate

Coated except lugs.

Lugs: Bright Dipped

Range

• 5331GR Series (straight fittings with

male hub): 3¼8” thru 6” conduit.

• 5341GR Series (45°): 3¼8” thru 4” conduit

• 5351GR Series (90°): 3¼8” thru 4” conduit.

• 5271GR Series (straight fittings

with female hub): 3¼8” thru 1-1/4”

conduit.

All hubs provided with taper pipe threads

(NPT)

Conformity

U.L. 467

U.L. 514B

CSA C22.2 No. 18.3

CSA C22.2 No. 41

NEMA FB-1

NFPA 70-2008 (ANSI)

JIC EGP1

JIC EMP1

Federal Specification W-F-406

Federal Standard H-28 (threads)

Series 5331GR

Series 5271GR

Sleeving

Raceway Jacket pulls off—exposing core and

affecting liquidtight termination. Feature (E) on

sealing ring helps overcome this problem.

CONFITMRO_EN_ALL.pdf 95 11/28/2011 11:05:36 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Straight Grounding Fittings*

Cat. No. Ground

Steel Steel Aluminum Conduit Dimensions (in.) Wire

Insulated Non-insulated Non-insulated Size A B C D

5331GR** 5231GR 5231ALGR* 3/8” 1-5/32 1-1/2 9/16 14-8

5332GR 5232GR 5232ALGR* 1/2” 1-3/8 1-9/16 9/16 14-8

5333GR 5233GR 5233ALGR* 3/4” 1-21/32 1-5/8 9/16 14-4

5334GR 5234GR 5234ALGR* 1” 1-7/8 2-1/16 3/4 14-4

5335GR 5235GR 1-1/4” 2-1/4 2-1/2 13/16 8-1/0

5336GR 5236GR 1-1/2” 3-1/4 2-11/16 13/16 4-2/0

5337GR 5237GR 2” 3-13/16 3-1/16 7/8 4-2/0

5338GR 5238GR 2-1/2” 4-7/16 4-1/8 1 2-4/0

5339GR 5239GR 3” 5-3/16 4-1/4 1 2-4/0

5340GR 5240GR 4” 6-1/8 4-1/2 1-1/8 2-4/0

5385GR 5285GR 5” 8-9/16 7 1-7/8 2-4/0

5386GR — 6” 8-17/32 8-1/2 2 2-4/0

45° Angle Grounding Fittings

Ground

Cat. No. Conduit Dimensions (in.) Wire

Insulated Non-insulated Size A B C D

5341GR** 5241GR** 3/8” 1-5/32 1-9/16 9/16 14-8

5342GR 5242GR 1/2” 1-3/8 1-7/8 9/16 14-8

5343GR 5243GR 3/4” 1-21/32 2-1/8 9/16 14-4

5344GR 5244GR 1” 1-7/8 2-1/4 3/4 14-4

5345GR 5245GR 1-1/4” 2-1/4 2-3/4 13/16 8-1/0

5346GR 5246GR 1-1/2” 3-1/4 3-3/8 13/16 4-2/0

5347GR 5247GR 2” 3-13/16 3-7/8 7/8 4-2/0

5348GR 5248GR 2-1/2” 4-7/16 4-1/4 1 2-4/0

5349GR 5249GR 3” 5-3/16 4-1/4 1 2-4/0

5350GR 5250GR 4” 6-1/8 4-5/8 1-1/8 2-4/0

90° Angle Grounding Fittings

Cat. No. Ground

Steel Steel Aluminum Conduit Dimensions (in.) Wire

Insulated Non-insulated Non-insulated Size A B C D

5351GR** 5251GR** 5251ALGR* 3/8” 1-5/32 1-1/4 9/16 14-8

5352GR 5252GR 5252ALGR* 1/2” 1-3/8 1-7/16 9/16 14-8

5353GR 5253GR 5253ALGR* 3/4” 1-21/321-13/16 9/16 14-4

5354GR 5254GR 5254ALGR* 1” 1-7/8 2-1/16 3/4 14-4

5355GR 5255GR 1-1/4” 2-1/4 2-1/2 13/16 8-1/0

5356GR 5256GR 1-1/2” 3-1/4 2-15/16 13/16 4-2/0

5357GR 5257GR 2” 3-13/16 3-7/16 7/8 4-2/0

5358GR 5258GR 2-1/2” 4-7/16 8-7/8 1 2-4/0

5359GR 5259GR 3” 5-3/16 10-1/4 1 2-4/0

5360GR 5260GR 4” 6-1/8 12-5/8 1-1/8 2-4/0

* Not CSA Certified

** 3/8” conduit fittings have 1/2” trade size hub. With safe-edge ground cone (through 4”)

and double bevel sealing ring (through 2”).

Suitable for hazardous locations use in Class I, Division 2; Class II, Division 1 and 2; Class III,

Division 1 and 2, where general purpose equipment is specifically permitted per CEC Rule

18-152 (6) Class I, Zone 2; CEC Rule J18-156 (3) Class I, Division 2;

CEC Rule 18-202 (4) Class II, Division. 1; CEC Rule 18-252 (4) Class II, Division 2.

Note: 3/8”-1” fittings include Revolver ™ grounding device. For sizes 1-1/4” and up, fittings are

supplied with a copper mechanical lug.

Malleable iron, tapered hub threads.

Malleable iron tapered hub threads.

Ground Wire

Max. over Ribs

Ground Wire

Max. over Ribs

CONFITMRO_EN_ALL.pdf 96 11/28/2011 11:05:36 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

External Grounding Strap

Conduit A B

Cat. No. Size Swing Radius Bolt Size

GR1W 3/8” 1 10-24

GR2W 1/2” 1-1/16 10-24

GR3W 3/4” 1-3/8 1/4-20

GR4W 1” 1-1/2 1/4-20

GR5W 1-1/4” 1-7/8 5/16-18

Liquidtight to Rigid External Ground Adaptor

Conduit A B C

Cat. No. Size Overall Length Bolt Size Lug Range

5271GR*3/8” 1-15/32 10-24 14-8

5272GR 1/2” 1-3/8 10-24 14-8

5273GR 3/4” 1-21/32 1/4-20 14-4

5274GR 1” 1-7/8 1/4-20 14-4

5275GR 1-1/4” 2-1/4 5/16-18 8-1/0

5276GR 1-1/4” 2-29/32 3/8-16 3/8-16

* 3/8” conduit fittings have 1¼2” trade size hub.

For Dura-Plate™finish add prefix 040- to Cat. No. Consult Customer Service for details.

Revolver®Grounding Device

Conduit

Cat. No. Size

38GR-TB 3/8”

12GR-TB 1/2”

34GR-TB 3/4”

1GR-TB 1”

The grounding device is a combination of a set screw and a grounding lug that can be used

to retrofit any existing liquidtight fithing to an externally grounded version.

For retrofit applications. Includes strap,

nut and bolt.

Swing

Radius Bolt

Bolt

Size

C Lug Range

CONFITMRO_EN_ALL.pdf 97 11/28/2011 11:05:36 AM

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Specifications — PVC Coated

Gland

Sealing

Ring

Ground

Cone (D)

Body

Sealing

Gasket

Locknut (H)

3321 Series

(B)

(A)

(C)

(E)

(A)

(F)

Leading

Edge Raceway Core

Convolutions

(G)

(I)

Taper

Threaded Hub

(F)

Trailing

Edge

3321 Series*

*3361 Series...same as 3321, except 90°

3341 Series...same as 3321, except 45°

Application

• Used where liquidtight flexible metal

conduit is installed in outdoor or

indoor locations where exposed to

environmental conditions that are

more than normally corrosive to

exposed surfaces.

• To positively bond conduit to box

or enclosure.

Features

• PVC coated to protect fitting from

extremely corrosive surroundings

without affecting integrity of electrical

grounding path (A).

• Provided with overlapping sleeve

for additional seal (B).

• Ability to install quickly with low

torque effort.

• Ground cone design offers following

advantages:

(1) Compresses metallic convolutions;

provides high quality ground

contact with low impedance and

high raceway holding power (C).

(2) Single helical thread on ground

cone is easy to install without

cross threading; accepts variations

in raceway diameters and

convolution pitch (D).

(3) Rolled over edge protects

conductors (E).

• Sealing ring design has following

exclusive features:

(1) Grips and seals at leading and

trailing edge—will not abrade

raceway jacket (F).

(2) Provided with grooves on inside

diameter for anti-sleeving (G).

(3) Shoulders on both ends for extra

sealing.

(4) Symmetrical shape assures

foolproof assembly.

• Hardened steel or malleable iron

locknut (H).

• Can be disconnected and reused.

• Watertight/oiltight installation at box

or enclosure termination is provided

by external taper thread hub and

sealing gasket (I).

• Suitable for use in Class I Division 2,

Class II Division 1, 2 and Class III

Division 1, 2 Hazardous Locations per

CEC Rule 18-152 (6) Class I, Zone 2;

CEC Rule J18-156 (3) Class I, Div. 2;

CEC Rule 18-202 (4) Class II, Div. 1;

CEC Rule 18-252 (4) Class II, Div. 2.

• Conforms with JIC requirements.

Standard Material

Body, Gland, Locknut and Ground

Cones: All steel or malleable iron.

Sealing Ring and Insulator:

All thermoplastic

Sealing Gasket, Retainer: Stainless

Steel

Resilient Seal: Buna N

Coating: PVC

Standard Finish

Outside of body and gland:

PVC Coated .040 min. Thickness

Inside of body and gland:

Electro Zinc Plated and Chromate

Coated

Locknut, Sealing Gasket, and Retainer:

Electro Zinc Plated and

Chromate Coated

Range

• 3321, 3361 and 3341 Series

3¼8” thru 4” conduit.

All hubs provided with taper pipe

threads (NPT).

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NEMA FB-1

NFPA 70-2008 (ANSI)

JIC EGP1

JIC EMP1

Federal Specification W-F-406

Federal Standard H-28 (THREADS)

CONFITMRO_EN_ALL.pdf 98 11/28/2011 11:05:37 AM

Corrosion Resistant PVC Jacketed

Liquidtight Fittings

Conduit Dimensions (in.)

Cat. No. Size A B C

Straight PVC Coated

3321 3/8 1-15/32 2-5/16 9/16

3322 1/2 1-5/8 2-1/2 9/16

3323 3/4 1-15/16 2-25/32 9/16

3324 1 2-1/4 3-15/32 3/4

3325 1-1/4 2-11/16 4-1/4 13/16

3326 1-1/2 3-1/8 4-11/16 13/16

3327 2 3-5/8 5-5/16 7/8

3328-TB 2-1/2 4-3/8 6-3/8 1

3329 3 5-3/16 6-1/2 1

3331 4 6-7/16 6-3/4 1-1/8

90° PVC Coated

3361 3/8 1-15/32 2-3/16 9/16

3362 1/2 1-5/8 2-1/2 9/16

3363 3/4 1-15/16 2-29/32 9/16

3364 1 2-1/4 3-19/32 3/4

3365 1-1/4 2-11/16 4-1/2 13/16

3366 1-1/2 3-1/8 4-15/16 13/16

3367 2 3-5/8 5-11/16 7/8

3368 2-1/2 4-3/8 11-1/8 1

3369 3 5-3/16 12-1/2 1

3371 4 6-7/16 14-7/8 1-1/8

45° PVC Coated

3341 3/8 1-15/32 1-1/8 9/16

3342 1/2 1-5/8 1-1/4 9/16

3343 3/4 1-15/16 1-7/16 9/16

3344-TB 1 2-1/4 1-13/16 3/4

3345 1-1/4 2-11/16 2-1/16 13/16

3346 1-1/2 3-1/8 2-11/16 13/16

3347 2 3-5/8 3-3/16 7/8

3348-TB 2-1/2 4-3/8 3-13/16 1

3349 3 5-3/16 4-9/16 1

3352 4 6-7/16 5-3/4 1-1/8

Complies with J.I.C. standards and Federal Specs W-F-406B, W-F-408B

Suitable for hazardous locations use in Class I, Div. 2; Class II, Div. 1 and 2; Class III, Div. 1

and 2, where general purpose equipment is specifically permitted per CEC Rule 18-156 (6)

Class I, Zone 2; CEC Rule J18-152 (3) Class I, Div. 2; CEC Rule 18-202 (4) Class II, Div. 1; CEC

Rule 18-252 (4) Class II, Div. 2.

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Straight PVC Coated

Nylon Insulated

Steel or Malleable Iron

NPT hub threads

90° PVC Coated

Nylon Insulated

NPT hub threads

45° PVC Coated

Nylon Insulated

NPT hub threads

CONFITMRO_EN_ALL.pdf 99 11/28/2011 11:05:37 AM

100

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Specifications —Liquidtight Union for Threaded Hub

Liquidtight Union for Threaded Hub

Conduit Dimensions (in.)

Cat. No. Size A B

41TB 1/2” 1-29/64 1

42TB 3/4” 1-15/16 1-1/4

(E)

(C)

(D)

Gland

Resilient Seal

(A)

Body

(B)

Controlled Deformation

of Resilient Seal

41 Series

Steel, zinc plated and chromated. Ideal for angle

fittings where swing clearance is not available.

Application

• To couple threaded end of a fitting or

a pipe to a tapped opening in a box

or enclosure where rotation of fitting

or pipe is limited or restricted.

Features

• Provides high quality bond between

fitting or pipe to the union.

• Provided with resilient seal (A).

• Resilient seal subjected to controlled

deformation; positive seal and

reusability are assured (B).

• Unique design centralizes throat

openings of threaded hub and union

(C).

• Permits orientation of fitting in any

predetermined direction for a safe,

functional and neat assembly.

• Provided with taper-threaded hub

for liquidtight assembly (D).

• Straight pipe threads on gland accept a

straight-or taper-threaded hub on

fitting or pipe to be coupled (E).

• Suitable for hazardous location

use per

CEC Rule J18-106 Class I, Div. 1;

CEC Rule 18-202 Class II, Div. 1;

CEC Rule 18-252 Class II, Div. 2;

CEC Rule 18-302 Class III, Div. 1;

CEC Rule 18-352 Class III, Div. 2;

Standard Material/Finish

Gland Steel/Electro Zinc

Chromate Coated

Body Steel/Electro Zinc

Chromate Coated

‘O’ Ring Buna N/As Molded

Range

• Hub (External Thread)

1/2” and 3/4” NPT

• Gland (Internal Threads)

1/2” and 3/4” NPS

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NEMA FB-1

ANSI C80.4

NFPA 70-2008 (ANSI)

Federal Specification W-F-408

Federal Specification W-F-406

Federal Standard H-28 (Threads)

CONFITMRO_EN_ALL.pdf 100 11/28/2011 11:05:37 AM

101

T&B Conduit Fittings

Liquidtight Flexible Nonmetallic Conduit Fittings

Application

• To provide a liquidtight, dustight

connection between flexible,

nonmetallic conduit and a box

or an enclosure.

Features

• Serrated design provides high

mechanical pullout strength (A).

• Unique component parts

(body/gland) design insures

positive seal between conduit

and fitting (B).

• Tapered thread hub and sealing ‘O’

ring provide a liquidtight/dust tight

seal to a box or an enclosure (C).

• High strength, chemical resistant,

non-burning, non-dripping

thermoplastic construction.

• Smooth insulated body throughout

for maximum dielectric strength.

• Captive ‘O’ ring and reduced number

of parts save installation time (D).

Standard Material

Body Thermoplastic

Gland Thermoplastic

‘O’ Ring Neoprene

Locknut Steel (Case Hardened)

Standard Finish

Body, Gland & ‘O’ Ring

As Molded

Locknut Electro Zinc

Range

• Conduit Size 1/2” thru 1-1/4”

• Hub Size 1/2” thru 1-1/4”

N.P.T.

• Type A Liquidtight Flexible Nonmetallic

Conduit shall be seamless type

adequately reinforced with one or

more layers of flexible braided

reinforcing cords. Conduit jacket shall

be of non-kinking oil resistant/water

resis-tant flame retardant material

suitable for ambient environmental

conditions.

• Where Type A Flexible Nonmetallic

Conduit terminates into a threaded

or threadless opening, the conduit

shall be cut square, deburred,

installed with sufficient slack to reduce

effects of vibration and assembled

with approved fittings such as series

6302 or 3720 manufactured by

Thomas & Betts. Fittings shall be of

malleable iron/steel/thermoplastic

construction with taper-threaded hub

and:

(1) Ferrous metallic fittings shall be

electro-zinc plated inside outside

and equipped with a nylon

insulated throat.

(2) Thermoplastic fittings shall be of

high impact chemical resistant,

non-burning, non-dripping

thermoplastic.

(3) Fittings shall be provided with a

captive, moisture resistant/oil

resistant synthetic rubber gasket.

Specifications — Type A Conduit Fittings

Suggested Specifications for Type A Conduit and Fittings

(A) Left-Handed Threads

Gland

Body

Sealing ‘O’ Ring

Locknut

Liquidtight Flexible

Nonmetallic Conduit

Gland

Body

Sealing ‘O’ Ring

(C)

Taper Threaded Hub

(A & B)

(D)

Captive Sealing

‘O’ Ring

Series 6302

Liquidtight Flexible Nonmetallic

Conduit Fittings

Series 6322

Liquidtight Flexible Nonmetallic

Conduit Fittings

CONFITMRO_EN_ALL.pdf 101 11/28/2011 11:05:37 AM

102

T&B Conduit Fittings

Liquidtight Flexible Nonmetallic Conduit Fittings

Thermoplastic Fittings for Liquidtight Flexible

Nonmetallic Conduit Type A

Dimensions (in.)

ABC

Conduit Cross

Cat. No. Size Corners

Straight Fitting

6302 1/2” .60 1.68 1.48

6303 3/4” .61 1.85 1.76

6304 1” .77 1.89 2.10

6305 1-1/4” .79 2.30 2.67

90° Angle Fitting

6322 1/2” .60 1.56 1.48

6323 3/4” .61 1.74 1.76

6324 1” .77 1.78 2.10

6325 1-1/4” .79 2.13 2.67

Corrosion Resistant Applications

Meets Coast Guard CG293

*Use with our LNM-P Conduit on p. 146

Liquidtight Flexible Nonmetallic Conduit Type A

Conduit Dimensions (in.)

Cat. No. Size Hub Thread A B

3720-TB* 3/8 1/2—14 NPT 1-5/32 2

3721-TB 1/2 1/2—14 NPT 1-3/8 2-1/8

3722-TB 3/4 3/4—14 NPT 1-5/8 2-1/4

3723 1 1—11-1/2 NPT 1-7/8 2-1/2

3724-TB 1-1/4 1-1/4—11-1/2 NPT 2-3/8 2

3725 1-1/2 1-1/2—11-1/2 NPT 2-3/4 3-3/8

3726 2 2—11-1/2 NPT 3-17/32 3-5/8

* Not U.L. Listed

For Dura-Plate™ Finish, add prefix 040- to Cat. No. Consult Customer Service for details.

90° Angle Fitting

Designed especially for the Type A, all-plastic

raceways now in use for dynamic machine tool

applications.

Fittings are constructed of a high-strength,

chemically resistant thermoplastic tougher than

the raceway itself.

Neoprene sealing ring is furnished with

fitting providing a liquidtight seal for knockout

applications.

Straight Fitting

• Nylon insulated throat.

• T&B Sealing Ring to seal knockouts.

• Steel or malleable iron.

• U.L. Listed.

• NPT hub threads to seal in female threads.

• High mechanical pull-out strength.

• Provides positive seal against water, oil and

dust.

CONFITMRO_EN_ALL.pdf 102 11/28/2011 11:05:38 AM

103

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

45° Metallic Fittings

Conduit Dimensions (in.)

Cat. No. Size Hub Thread A B

3730-TB* 3/8 1/2—14 NPT 1-5/32 2-13/32

3731-TB 1/2 1/2—14 NPT 1-3/8 2-9/16

3732 3/4 3/4—14 NPT 1-5/8 3

3733-TB 1 1—11-1/2 NPT 1-7/8 3-1/2

3734-TB 1-1/4 1-1/4—11-1/2 NPT 2-3/8 4-1/8

3735-TB 1-1/2 1-1/2—11-1/2 NPT 2-3/4 4-7/8

3736 2 2—11-1/2 NPT 3-17/32 5-1/2

* Not U.L. Listed

Available with Dura-Plate™ Finish. Consult Customer Service for details.

90° Metallic Fittings

Conduit Dimensions (in.)

Cat. No. Size Hub Thread A B

3740* 3/8 1/2—14 NPT 1-5/32 1-5/8

3741 1/2 1/2—14 NPT 1-3/8 1-3/4

3742 3/4 3/4—14 NPT 1-5/8 2-1/4

3743-TB 1 1—11-1/2 NPT 1-7/8 2-9/16

3744-TB 1-1/4 1-1/4—11-1/2 NPT 2-3/8 3-1/4

3745 1-1/2 1-1/2—11-1/2 NPT 2-3/4 3-1/2

3746-TB 2 2—11-1/2 NPT 2-17/32 4-1/8

* Not U.L. Listed

Available with Dura-Plate™ Finish. Consult Customer Service for details..

Liquidtight K.O. Plugs

Dimensions (in.)

Cat. No. Size A

5710 1/2” 1-9/32”

5711 3/4” 1-1/2”

5712 1” 1-27/32”

5713 1-1/4” 27/32”

5714 1-1/2” 2-1/2”

5715 2” 3-3/32”

5716 2-1/2” 3-21/32”

5717 3” 4-19/64”

5718 4” 5-19/64”

U.L. Listed liquidtight

CSA not applicable

Meets Coast Guard Regulation CG293

NEMA 3R, 4, 6 & 13

Temperature range — -30°C to 105°C.

CONFITMRO_EN_ALL.pdf 103 11/28/2011 11:05:38 AM

104

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

Specifications — Liquidtight Sealing Gaskets

B Thickness

5262 Series

NEMA 3R, 4, 6 & 13

For use with T&B Fittings. Sealing material

resists oil, coolants, and hydraulic fluids as well

as water.

Application

• When used with an externally

threaded fitting provides a tight seal

against oil, fumes or moisture at the

knockout opening.

Features

• Locks resilient sealing material in

steel.

• Steel retainer protects seal from

extruding out under torque and

limits compression to an optimum

predetermined value; provides high

quality seal.

• Resilient material flows and

seals rough surfaces.

Standard Material

Retainer Stainless Steel

Sealing Material Buna N

Range

• 1/2” thru 4” Hub Size

Stainless Steel Retainer

Resilient Seal

Resilient Sealing

Material Locked in Steel Retainer

Sealing Ring with Stainless Steel Retainer

Conduit Dimensions (in.)

Cat. No. Size A B

5299** 1/4” .80 .11

5261** 3/8” .95 .11

5262 1/2” 1.16 .18

5263 3/4” 1.49 .19

5264 1” 1.75 .19

5265 1-1/4” 2.15 .22

5266 1-1/2” 2.42 .23

5267 2” 2.92 .23

5268 2-1/2” 3.44 .23

5269 3” 4.08 .23

5270 4” 5.29 .31

** U.L. not applicable

CONFITMRO_EN_ALL.pdf 104 11/28/2011 11:05:38 AM

105

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

PG Metric Thread Liquidtight Fittings*

Flexible Metric

Conduit PG Dimensions (mm)

Cat. No. Size Thread A B C

Nylon insulated straight fittings

7330** 1/4” 9 36 21 12

7360** 5/16” 9 362612

7361* 3/8” 11 40 29 14

7362* 3/8” 13.5 40 29 14

7363* 1/2” 16 41 35 14

7364* 3/4” 21 43 42 14

7365 1” 29 56 47 19

7366 1-1/4” 36675821

7367 1-1/2” 42726921

7368 2” 48 81 83 21

Nylon insulated 45° angle fittings

7341 3/8” 11 27 29 14

7342 3/8” 13.5 27 29 14

7343 1/2” 16 30 35 14

7344-TB 3/4” 21 34 42 14

7345 1” 29 44 47 19

7346 1-1/4” 36515819

7347 1-1/2” 42606921

7348-TB 2” 48 73 76 24

Nylon insulated 90° angle fittings

7351 3/8” 11 37 29 14

7352 3/8” 13.5 37 29 14

7353 1/2” 16 40 35 14

7354 3/4” 21 44 42 14

7355 1” 29 56 47 21

7356 1-1/4” 36 70 58 21

7357 1-1/2” 42 75 69 21

7358 2” 48 87 83 24

U.L. Listed liquidtight.

*CSA Certified dusttight and watertight.

**U.L. not applicable and not CSA Certified.

Fittings for Liquidtight flexible metal conduit

with metric threads of PG Form (DIN 40430).

Liquidtight Flexible Metal/MS Fittings

Internal Thread

Trade AN-MS Conn. Dimensions (in.)

Cat. No. Size Shell Size Thread Size A B

LTA03810 3/8 10SL, 12, 12S 5/8—24 UNEF-2B 1-5/32 1

LTA03814 3/8 14, 14S 3/4—20 UNEF-2B 1-5/32 1

LTA05014 1/2 14, 14S 3/4—20 UNEF-2B 1-5/16 1-1/4

LTA05016 1/2 16, 16S 7/8—20 UNEF-2B 1-5/16 1-1/4

LTA05018 1/2 18 1—20 UNEF-2B 1-5/16 1-1/4

LTA07516 3/4 16, 16S 7/8—20 UNEF-2B 1-7/16 1-1/2

LTA07518 3/4 18 1—20 UNEF-2B 1-7/16 1-1/2

LTA07520 3/4 20, 22 1-3/16 —18 UNEF-2B 1-7/16 1-1/2

LTA10020 1 20, 22 1-3/16 —18 UNEF-2B 1-3/4 1-23/32

LTA10024 1 25, 28 1-7/16 —18 UNEF-2B 1-3/4 1-23/32

T&B Liquidtight flexible metal and Liquidtight

flexible nonmetallic fittings with internal

threads to accept AN-MS fitting shells.

Material: Steel

CONFITMRO_EN_ALL.pdf 105 11/28/2011 11:05:38 AM

106

T&B Conduit Fittings

Liquidtight Flexible Metal Conduit Fittings

ISO Metric Thread Liquidtight Fittings*

Flexible Metric

Conduit ISO Dimensions (mm)

Cat. No. Size Thread A B C

Nylon insulated straight fittings

9330 1/4” 16 36 21 12

9331 1/4” 20 36 21 12

9306 5/16” 16 36 26 12

9360 3/8” 16 40 29 16

9361 3/8” 20 40 29 16

9362 1/2” 20 42 35 16

9363 3/4” 25 45 42 16

9364 1” 32 54 47 23

Nylon insulated 45° angle fittings

9340 3/8” 16 27 29 16

9341 3/8” 20 27 29 16

9342 1/2” 20 27 35 16

9343TB 3/4” 25 31 42 16

9344 1” 32 34 47 23

Nylon insulated 90° angle fittings

9350 3/8” 16 35 29 16

9351 3/8” 20 35 29 16

9352TB 1/2” 20 39 35 16

9353TB 3/4” 25 43 42 16

9354TB 1” 32 48 47 23

U.L. Listed Liquidtight.

NPT/MS Fitting Adaptors

AN-MS

N.P.T. Fitting Thread Dimensions (in.)

Cat. No. Thread Shell Size Size A Fig. B

MSA05014 1/2” 14, 14S 3/4—20 UNEF-2B 1.000 1 1.175

MSA05016 1/2” 16, 16S 7/8—20 UNEF-2B 1.000 2 1.175

MSA05018 1/2” 18 1—20 UNEF-2B 1.125 3 1.175

MSA07516 3/4” 16, 16S 7/8—20 UNEF-2B 1.250 1 1.356

MSA07518 3/4” 18 1—20 UNEF-2B 1.250 1 1.300

MSA07520 3/4” 20, 22 1-3/16 —18 UNEF-2B 1.375 3 1.300

MSA10020 1 20, 22 1-3/16 —18 UNEF-2B 1.500 1 1.431

MSA10024 1 24, 28 1-7/16 —18 UNEF-2B 1.625 3 1.313

MSA10032 1 32 1-3/4—18 UNS-2B 2.000 3 1.576

MSA10036 1 36 2—18 UNS-2B 2.250 3 1.738

Not CSA Certified.

Fittings for Liquidtight flexible metal conduit with

metric threads of ISO Form (BS-4568-SA BS 162).

Fig. 1

Fig. 2

Fig. 3

Mechanical adapter with internal threads to

mate with NPT threaded fittings and MS type

fittings.

Material: aluminum

CONFITMRO_EN_ALL.pdf 106 11/28/2011 11:05:38 AM

107

T&B Conduit Fittings

Liquidtight Flexible Nonmetallic Conduit Fittings

Specification Sheet—Bullet®Liquidtight Fittings for

Liquidtight Flexible Nonmetallic Conduit and Tubing

Box or

Enclosure

Wall

Conduit

or Tubing

Application:

A series of nonmetallic fittings designed

to provide a liquidtight seal when

terminating liquidtight nonmetallic

conduit (U.L. Type B) or liquidtight

nonmetallic tubing to a box or enclosure

with knockout opening or a threaded

hub.

Plastic Bullet®Liquidtight Fittings

Feature:

• Fitting assembles to conduit without

disassembly and is designed to be

installed with positive installation

criteria (gland bottoms on body

shoulder).

• Rugged low profile nonmetallic body

and gland construction (1); the fitting is

equipped with a steel locknut to firmly

secure fitting to box or an enclosure

and a sealing “O” ring.

• Captive sealing “O” ring (2) with

predetermined compression for a

reliable seal at enclosure.

• Fitting ferrule designed to accept

variations in conduit inside diameter

and is tolerant of field conduit cuts (3).

• Ferrule profile designed to reduce

friction between conduit I.D. and

ferrule (4) allowing conduit to seat

properly for an effective seal.

• Outer surface of clamping fingers

provided with friction reducing ridges

(5) for ease of installation; the inner

surface is designed with conduit

biting teeth to enhance clamping and

sealing action (6).

• Performance of fittings tested to

simulate adverse installation

conditions.

• Provides a double sealing action (7).

• Elongated gland nut profile (8)

designed to provide additional strain

relief for 90° pull and an easy hand

grip.

• Performance of fitting unaffected by

exposure to detergents, cleaners, and

sanitizers commonly encountered in

food processing plants and typical

industrial environment; also

unaffected by cutting fluids, wiring

pulling compounds and Marine

environment.

• Meets industry standards for cold

impact and simulated hammer blow.

Standard Material/Finish:

• Body Gland—weather stabilized

thermoplastic (black).

• “O” Ring—nitrile (blue)

• Locknut—Steel/electro-zinc plated

• Material temperature rating—

thermoplastic -40°C to 105°C.

• Material Flammability Rating:

U.L.94-V2.

Conformity

• CSA C22.2 #227.2 & CSA

C22.2 #227.3

• U.L.514B

• Watertight requirements of NEMA

Type 4 and Type 4X.

• Federal Standard H-28 (NPT threads)

• There is no CEC Rule to use

Nonmetallic liquidtight conduit and

fittings in Class I, Zone 2 or Class I,

Division 2;

Rule 18-202 (4) (b) Class II, Division 1;

Rule 18-252 (4) Class II, Division 2; Rule

18-302 (4) Class III, Division 1.

CONFITMRO_EN_ALL.pdf 107 11/28/2011 11:05:38 AM

108

T&B Conduit Fittings

Liquidtight Flexible Nonmetallic Conduit Fittings

Plastic Bullet®Liquidtight Fittings for T&B NMC

Nonmetallic Liquidtight Conduit Type B and T&B NMT Flexible Tubing

C ±.015 (0.40) Min.

A ±.015 Across Throat E F*

Trade (.040) *B ±.035 (0.90) Corners Dia. D Thread (in.) (mm)

Cat. No. Fig. Size in. (mm) in. (mm) in. (mm) in. (mm) NPT Approx.

LT38P 1.570 1.595 (40.51) 1.354 .417 —

LT438P 2 3/8 2.012 (51.10) 1/2-14 1.534 (38.95)

LT938P 3(14.48) 1.380 (35.05) (34.39) (10.59) 1.880 (47.75)

LT50P 1.570 1.636 (41.55) 1.448 .550 —

LT450P 2 1/2 2.092 (53.14) 1/2-14 1.590 (40.39)

LT950P 3(14.48) 1.489 (37.82) (36.78) (13.97) 1.986 (50.44)

LT75P 1.582 1.757 (44.63) 1.740 .740 —

LT475P 2 3/4 2.452 (62.28) 3/4-14 1.821 (46.25)

LT975P 3(14.78) 1.790 (45.47) (44.20) (18.80) 2.212 (56.00)

LT100P 1.726 1.923 (48.84) 2.068 .940 —

LT4100P 2 1 2.684 (68.17) 1-11-1/2 2.034 (51.66)

LT9100P 3(18.44) 2.104 (53.44) (52.53) (23.88) 2.508 (63.70)

LT125P 1.750 2.164 (54.97) 2.494 1.257 —

LT4125P 2 1-1/4 3.264 (82.91) 1-1/4-11-1/2 2.385 (60.58)

LT9125P 3(19.05) 2.564 (65.13) (63.35) (31.93) 2.856 (72.54)

LT150P 1.767 3.353 (59.77) —

LT4150P 2 1-1/2 3.605 (91.57) 2.784 1.453 1-1/2-11-1/2 2.604 (66.14)

LT9150P 3(19.48) 2.854 (72.49) (70.71) (36.91) 3.144 (79.86)

LT200P 1.794 2.605 (66.17) 3.362 1.883 —

LT4200P 2 2 4.210 (106.93) 2-8 3.050 (77.47)

LT9200P 3(20.17) 3.432 (87.17) (85.39) (47.83) 3.675 (93.34)

* After Assembly

Figure 1 Figure 2 Figure 3

E Thread E Thread E Thread

Suggested Specification:

Where liquidtight flexible nonmetallic

conduit (U.L. and CSA Type B) or

liquidtight flexible nonmetallic tubing

is terminated to a box or enclosure, the

nonmetallic fittings used shall be able to

be installed without disassembly and

provide a positive installation criteria. In

the installed condition, the fitting must

provide a seal meeting watertight

requirements of NEMA Type 4 and Type

4X. The performance of fittings shall be

unaffected by exposure to detergents,

sanitizers, cutting fluids, wire pulling

compunds and oil-based industrial

paints. The fitting must also be capable

of withstanding marine environment and

cold impact simulating a hammer blow.

Installed fittings shall be of the

elongated gland type as

manufactured by Thomas & Betts

LT38P series.

CONFITMRO_EN_ALL.pdf 108 11/28/2011 11:05:39 AM

109

T&B Conduit Fittings

Liquidtight Flexible Conduit Fittings

Metallic Bullet®Liquidtight Fittings for T&B NMC

Non metallic Liquidtight Conduit Type B and T&B NMT Flexible Tubing

A ±.030* B ±.060 C ±.045

Trade (.80) (1.50) (1.15) D Thread

Cat. No. Fig. Size in. (mm) in. (mm) in. (mm) in. (mm) NPT

LT38M 11.156 1.500 (38.1) 0.562 (14.3) —

LT438M 2 3/8 1.962 (49.8) 0.562 (14.3) 1/2-14

LT938M 3(29.4) 1.312 (33.3) 0.625 (15.9) 1.375 (34.9)

LT50M 11.375 1.562 (39.7) 0.562 (14.3) —

LT450M 2 1/2 1.875 (47.6) 0.562 (14.3) 1/2-14

LT950M 3(34.9) 1.437 (36.5) 0.625 (15.9) 1.562 (39.7)

LT75M 11.656 1.625 (41.2) 0.625 (15.9) —

LT475M 2 3/4 2.125 (54.0) 0.562 (14.3) 3/4-14

LT975M 3(42.1) 1.750 (44.4) 0.625 (15.9) 1.750 (44.4)

LT100M 11.875 2.062 (52.4) 0.750 (19.0) —

LT4100M 2 1 2.250 (57.1) 0.812 (20.6) 1-11-1/2

LT9100M 3(47.6) 1.937 (49.2) 0.812 (20.6) 2.187 (55.5)

LT125M 12.375 2.500 (63.5) 0.812 (20.6) —

LT4125M 2 1-1/4 2.750 (69.8) 0.812 (20.6) 1-1/4-11-1/2

LT9125M 3(60.3) 2.500 (63.5) 0.812 (20.6) 2.750 (69.8)

LT150M 12.750 2.687 (68.2) 0.812 (20.6) —

LT4150M 2 1-1/2 2.750 (69.8) 0.812 (20.6) 1-1/2-11-1/2

LT9150M 3(69.8) 2.812 (71.4) 0.812 (20.6) 2.937 (74.6)

LT200M 13.468 3.062 (77.8) 0.812 (20.6) —

LT4200M 2 2 3.875 (98.4) 0.875 (22.2) 2-11-1/2

LT9200M 3(88.1) 3.500 (88.9) 0.875 (22.2) 3.437 (87.3)

*After Assembly

Suggested Specification:

Where liquidtight flexible nonmetallic

conduit (U.L. and CSA Type B) or

liquidtight flexible nonmetallic tubing is

terminated to a box or enclosure, the

metallic fittings used shall be able to be

installed without disassembly and provide

positive installation criteria. In the installed

condition, the fitting must provide a seal,

meeting watertight requirements of NEMA

Type 4 and Type 4X with conduit and

NEMA Type 4 enclosures with tubing.

Installed fittings shall be as manufactured

by Thomas & Betts LT38M series.

Material: Body/Gland—Steel/MI

Insert—Nylon

Figure 1 Figure 2 Figure 3

CONFITMRO_EN_ALL.pdf 109 11/28/2011 11:05:39 AM

110

T&B Conduit Fittings

Liquidtight Flexible Nonmetallic Conduit Fittings

When you have a conduit application in a liquidtight environment, it's time to load

up the T&B Bullet®. Thomas & Betts introduces the ISO Metric Bullet®liquidtight

fittings for use with the 3/8”, 1/2”, and 3/4” NMT and NMC nonmetallic

liquidtight conduit series.

The T&B Bullet®liquidtight fitting and NMT nonmetallic conduit

are suited for OEM applications as in the machine tool industry

where environments include continuous motion, vibration,

and exposure to moisture, oil, dirt and dust.

The T&B Bullet®liquidtight fitting and NMT nonmetallic conduit

are also suitable for construction applications where ISO

metric threading and liquidtight systems are installed.

The Xtraflex®system offers a lightweight, liquidtight flexible

conduit solution for industrial applications. The Xtraflex®

system allows fast, easy installation and high performance

in demanding industrial applications.

ISO Metric Bullet®Liquidtight Fitting

Cat. Angle Conduit Knockout Unit Standard UPC

No. of Fitting Size (in.) Size (in.) Package Package Number

LT38M-ISO20 Straight 3/8 1/2 25 100 786210-62281

LT50M-ISO20 Straight 1/2 1/2 25 100 786210-62282

LT75M-ISO25 Straight 3/4 3/4 25 50 786210-62283

LT438M-ISO20 45° 3/8 1/2 25 50 786210-62284

LT450M-ISO20 45° 1/2 1/2 25 50 786210-62285

LT475M-ISO25 45° 3/4 3/4 10 50 786210-62286

LT938M-ISO20 90° 3/8 1/2 25 50 786210-62288

LT950M-ISO20 90° 1/2 1/2 25 50 786210-62289

LT975M-ISO25 90° 3/4 3/4 10 50 786210-62290

ISO Metric Bullet®Liquidtight Fitting Nonmetallic

Cat. Angle Conduit Knockout Unit Standard UPC

No. of Fitting Size Size Package Package Number

LT38P-ISO20 Straight 3/8” 1/2” 25 100 786210-66444

LT50P-ISO20 Straight 1/2” 1/2” 25 100 786210-66613

LT75P-ISO25 Straight 3/4” 3/4” 25 50 786210-66443

LT938P-ISO20 90° 3/8” 1/2” 25 50 786210-66612

LT950P-ISO20 90° 1/2” 1/2” 25 50 786210-66640

LT975M-ISO25 90° 3/4” 3/4” 10 50 786210-66611

ISO Metric Bullet™Liquidtight Fittings

CONFITMRO_EN_ALL.pdf 110 11/28/2011 11:05:39 AM

111

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Armoured Cable (Type AC90)

Ref. CEC Rule 12-600

The Canadian Electric Code 2009 Part I

defines type AC armoured cable as,

“A fabricated assembly of insulated

conductors in a flexible metallic

enclosure.”

All armoured cables may employ

copper or aluminum or copperclad

aluminum conductors with the following

sizes and are rated for 600 volts or less:

No. 14 AWG to No. 1 AWG Copper

No. 12 AWG to No. 1 AWG Aluminum

or Copperclad Aluminum

Armoured cable can be used for both

exposed or concealed locations.

Armoured cable is not permitted in

locations where it will be subjected to

physical damage or corrosive fumes.

Armoured cable cannot be used for

direct burial in earth.

Codes require that cable shall be

supported with straps or staples

without damaging conductors. Certain

precautions are prescribed in code

where cable is installed through joist

rafters or similar wood members.

According to CEC Rule 12-610

(1) Where conductors issue from

armour, they shall be protected from

abrasion by bushings of insulating

material or equivalent devices.

(2) Where conductors are No. 10 AWG

or larger, copper or aluminum, such

protection shall consist of:

(a) Insulated type bushings, unless

the equipment is equipped with a

hub having a smoothly rounded

throat; or

(b) Insulating material fastened

securely in place which will separate

the conductors from armoured cable

fittings and afford adequate

resistance to mechanical injury.

(3) Where armoured cable is fastened to

equipment, the conductor or clamp

shall be of such design as to leave

the insulating bushing or its

equivalent visible for inspection.

(4) Where conductors connected to

open wiring issue from the ends of

armouring, they shall be protected

with boxes or with fittings having a

separately bushed hole for each

conductor.

Please refer to the following for further

details and complete information:

1. U.L. 4, ANSI C33.9….............Safety

Standards for Armoured Cable

2. U.L. 514.................................Safety

Standards for Outlet Boxes

and Fittings

3. W-F-406… .....Federal Specification:

Fittings for Cable, Power, Electrical

and Conduit, Metal, Flexible

4. NEMA FB-1… ..Standards Publication:

Fittings & Supports for Conduit

and Cable Assemblies

5. CEC Section 12-600… ..........Wiring

Methods (Armoured Cable)

6. CSA C22.2 No. 51… .............Safety

Standards for Armored Cables

7. CSA C22.2 No. 18… .............Safety

Standards for Outlet Boxes,

Conduit Boxes and Fittings

Specifications — Armoured Cable and Flexible Metal Conduit

Please Note

The excerpts and other material herein, whether relating to the Canadian Electrical

Code 2009 Part I, the Underwriters Laboratories, Inc. listing, to

industry practice or otherwise, is not intended to provide all relevant information

required for use and installation. Reference to original or primary source

material and data is mandatory before any application or use is made of the

product.

CONFITMRO_EN_ALL.pdf 111 11/28/2011 11:05:39 AM

112

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Flexible Metal Conduit

Ref. CEC Rule 12-1000

Flexible metal conduit can be used for

exposed or concealed work in dry

locations. It can be used for wet

locations provided conductors within

are lead covered or other approved

type.

Flexible metal conduit cannot be

used underground or embedded in

poured concrete or aggregate. With

rubber covered conductors the conduit

cannot be exposed to oil, gasoline or

other materials having a deteriorating

effect on rubber.

With minor exceptions use of flexible

metal conduit is not permitted in hoists,

in storage battery rooms and in any

hazardous locations. Use of flexible metal

conduit is restricted to systems under

600 volts.

Flexible metal conduit longer than six

feet is permitted to be used as a

grounding means provided the conduit

and the fitting are approved for the

purpose. To date there is no flexible

metal conduit approved for the purpose

by the Underwriters Laboratories or CSA.

In Class II Zone 2 and Division 2

hazardous areas, the conduit itself

cannot be used as the grounding

means. Class I Zone 2, flexible

connections at motor terminals and

similar places, ref.: CEC Rule 18-152 (6)

and Bonding CEC Rule 18-074 (1)(a).

Class I Division 2, flexible connections at

motor terminals and similar places, ref:

CEC Rule J18-152 (3) and Bonding CEC

Rule J18-072 (1)(a). Flexible metal

conduit is available with steel or

aluminum armour in trade size 5/16” to

4”. With few exceptions where 5/16 and

3/8 trade sizes are used, Code prohibits

use of conduit less than 1/2” trade size.

Bends in concealed work are restricted

to four 90° bends CEC Rule 12-940. No

angle fittings are permitted in concealed

raceway installations.

Please refer to the following for further

details and complete information:

1. U.L. 1, ANSI C33.92…...........Safety

Standards for Flexible Metal Conduit

2. U.L. 514.................................Safety

Standards for Outlet Boxes

and Fittings

3. W-F-406… .....Federal Specification:

Fittings for Cable, Power,Electrical

and Conduit, Metal Flexible

4. WW-C-566… .....Federal Specification:

Conduit, Metal, Flexible

5. NEMA FB1… Standards Publication:

Fittings and Supports

for Conduit and Cable Assemblies

6. CEC 12-1000… ........Wiring Method

(Rigid & Flexible Conduit)

7. CSA C22.2 No. 56… .............Safety

Standards for Flexible Metallic

Conduit and Liquid-Tight Flexible

Metal Conduit

8. CSA C22.2 No. 18… .............Safety

Standards for Outlet Boxes, Conduit

Boxes and Fittings

9. CEC Rule 12-1000

Rule 18-152 (6) and Bonding Rule

18-074 (1)(a) Class I, Zone 2 Flexible

connections at motor terminals and

similar places.

Rule J18-152 (6) and Bonding Rule

J18-072 (1)(a) Class I, Division 2

Flexible connections at motor

terminals and similar places.

Rule 12-940 ........Not more than the

equivaleent of four 90° bends CEC

Specifications — Armoured Cable and Flexible Metal Conduit (continued)

CONFITMRO_EN_ALL.pdf 112 11/28/2011 11:05:39 AM

113

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Suggested Specifications for Armoured Cable and Flexible

Metal Conduit Fittings

Series 3110

Armoured Cable Fitting

& Flexible Metal Conduit

Series 422

Insuliner Sleeve

Series 390

Anti Short Bushing

• Armoured cable and flexible metal

conduit shall conform to provisions of

following applicable standards:

Armoured Cable…U.L. 4/ANSI

C33.9/CSA C22.2 No. 51

Flexible Metal Conduit…U.L. 1/ANSI

C33.92/WW-C-566/CSA C22.2 No.56

• Type of cable used and conductors

within flexible metal conduit shall be

suitable for conditions of use and

location.

• Where armoured cable or flexible

metal conduit terminates into a

threadless or threaded opening it

shall be assembled with approved

fittings; fittings shall be of malleable

iron/steel construction, electro-zinc

plated inside outside, equipped with

nylon insulated throat and shall be of

angled saddle type as manufactured

by Thomas & Betts, series 3110.

Direct bearing screw type

fittings shall not be used.

• Suitable bushing as manufactured by

Thomas & Betts, series 422 or 390,

shall be provided between

the conductors and armour.

• Where approved armoured cable or

flexible metal conduit is used as an

equipment grounding conductor

terminating fitting used shall be of the

grounding type as manufactured by

Thomas & Betts, series 3110.

CONFITMRO_EN_ALL.pdf 113 11/28/2011 11:05:40 AM

114

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Application

• To connect and effectively bond

armoured cable or flexible metal

conduit to a box or an enclosure.

Features

• Provided with a saddle designed to:

(1) Firmly secure conduit in place

without damaging cable armour

(Mechanical holding power of

angled wedge assembly increases

with increased strain.).

(2) Provide high quality bond

between conduit or cable and are

unaffected by vibrations.

(3) Centralize conduit or cable with

respect to throat opening for

conductors.

• Insulated throat protects conductors

during and after installation, reduces

wire pull effort and prevents thread

damage in handling.

• Locknuts designed to provide

effective bond between fitting and

box or enclosure, will not vibrate

loose.

• Designed with fewer screws—

reduces installation time and cost.

• Rugged all steel or malleable iron

construction.

• CEC Rule 18-152 (6) and Bonding

Rule 18-074 (1)(a) Class I, Zone 2

Flexible connections at motor

terminals and similar places.

CEC Rule J18-152 (6) and Bonding

Rule J18-072 (1)(a) Class I, Division 2

Flexible connections at motor

terminals and similar places.

Standard Material/Finish

Body: Steel or malleable iron/

Electro Zinc Plated &

Chromate Coated

Saddle: Steel/Electro Zinc Plated

& Chromate Coated

Screws: Steel/Electro Zinc Plated

& Chromate Coated

Insulator: Thermoplastic/As

Molded

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NEMA FB-1

Specifications

3110 Series

Cable

Series Hub Size Conduit Size Opening

3110 Series 1/2" thru 5" NPS 3/8" thru 5" .437" to

Straight Fittings 5.500"

3130 Series 90° Fittings 1/2" thru 4" NPS 3/8" thru 4" .437" to

4.560"

(All hubs provided with

straight pipe threads NPS.)

Locknut Saddle

Typical

Installation

Body

Box or Enclosure Wall

Insulated Throat

CONFITMRO_EN_ALL.pdf 114 11/28/2011 11:05:40 AM

115

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Tite-Bite®Fittings—Nylon Insulated

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

3110-C*.656 .437 3/8” 1/2” 1-7/16 1-5/16 7/16

3112 .937 .750 1/2” 1/2” 1-25/32 1-3/4 1-9/32

3115*1.125 .906 3/4” 3/4” 2 1-3/4 1-9/32

3117*1.468 1.250 1” 1” 2-3/8 1-3/4 1-7/32

3118†1.750 1.562 1-1/4” 1-1/4” 2-3/4 2 1-11/32

3119†2.031 1.812 1-1/2” 1-1/2” 3-1/8 2-5/8 1-7/8

3120†2.500 2.312 2” 2” 3-3/4 2-3/4 1-15/16

3121†3.062 2.812 2-1/2” 2-1/2” 4-3/8 3-1/4 2-3/8

3122†3.562 3.312 3” 3” 5 3-1/4 2-3/8

3123‡4.060 3.620 3-1/2” 3-1/2” 5-1/4 3-11/16 2-15/32

3124**†4.560 4.120 4” 4” 5-3/4 3-25/32 2-1/2

3125** 5.500 4.600 5” 5” 6-7/8 4-27/32 3

Material: Steel thru 3/4” trade size.

* U.L. Listed for armoured cable only.

† U.L. Listed for flexible metal conduit only.

‡ CSA not applicable.

** Not U.L. Listed or CSA Certified.

Tite-Bite®Fittings

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

300-TBC* .656 .437 3/8” 1/2” 7/16 1-5/16 7/16

302-C .937 .750 1/2” 1/2” 1-7/64 1-11/16 3/4

304 1.093 .906 3/4” 3/4” 1-7/32 1-11/16 29/32

306 1.468 1.250 1” 1” 1-1/8 1-3/4 1-1/4

308†1.750 1.562 1-1/4” 1-1/4” 1-1/4 2-1/32 1-9/16

310†2.031 1.812 1-1/2” 1-1/2” 1-3/4 2-9/16 1-13/16

312†2.500 2.312 2” 2” 1-13/16 2-13/16 2-5/16

314†3.062 2.812 2-1/2” 2-1/2” 2-1/4 3-1/8 2-13/16

316†3.562 3.312 3” 3” 2-1/4 3-3/16 3-5/16

Material: Steel thru 3/4” trade size.

* U.L. Listed for armoured cable only.

†U.L. Listed for flexible metal conduit only.

Steel or malleable iron.

The tough lining of insulation and the Tite-Bite

principles make these fittings a “must” when

conductors are subject to conditions of vibration

or strain.

Steel or malleable iron.

Easy to install with double grip saddle. These

fittings are completely salvageable. The 2/3”

and 1/2” sizes are made of formed steel which

produce a uniform high quality and a smooth

throat that protects conductor insulation. 3/4”

and larger size are malleable iron.

CONFITMRO_EN_ALL.pdf 115 11/28/2011 11:05:40 AM

116

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Tite-Bite®Fittings—90° Angle Nylon Insulated

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

3130-C .563 .437 3/8” 1/2” 1-11/32 1-19/32 5/32

3132 .937 .750 1/2” 1/2” 1-7/8 2-5/16 1-5/32

3135 1.093 .906 3/4” 3/4” 2 2-1/8 1-5/32

3137 1.468 1.250 1” 1” 2-21/32 2-1/8 1/2

3138†1.750 1.562 1-1/4” 1-1/4” 3-1/8 2-7/8 3/4

3139†2.031 1.812 1-1/2” 11-1/2” 4-3/8 4 1-3/16

3140†2.500 2.312 2” 2” 5-9/16 4-7/8 1

3141†3.062 2.812 2-1/2” 2-1/2” 5-25/32 6 21

3142†3.562 3.312 3” 3” 6 7 1

3143‡4.060 3.620 3-1/2” 3-1/2” 6 6-7/8 1-1/16

3144-TB‡4.560 4.120 4” 4” 6-29/32 7-1/4 1-1/8

†U.L. Listed for flexible metal conduit only.

‡Not U.L. Listed or CSA Certified.

Tite-Bite®Fittings— 90° Angle

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

321-C .656 .437 3/8” 1/2” 1-11/32 1-1/2 3/8

323 .937 .750 1/2” 1/2” 1-7/8 2-3/8 1-7/32

325 1.093 .906 3/4” 3/4” 2-1/8 2-1/8 3/4

326-TB 1.468 1.250 1” 1” 2-21/32 2-1/8 1

327†1.750 1.562 1-1/4” 1-1/4” 3-1/8 3-5/8 —

328†2.031 1.812 1-1/2” 1-1/2” 4-1/8 4-1/8 —

329†2.500 2.312 2” 2” 4-3/8 4-31/32 —

330-TB†3.062 2.812 2-1/2” 2-1/2” 6-1/2 6 —

331†3.562 3.312 3” 3” 5-25/32 7 —

†U.L. Listed for flexible metal conduit only.

The angle clip gives secure mechanical grip that

tightens under tension or vibration. Throat is

long enough to install in cast housing

knockouts. The 3/8” and 1/2” sizes are of steel

construction. The 3/4” and larger sizes are

malleable iron.

Steel or malleable iron.

Available with or without insulated throat, this

Tite-Bite fitting line is by far the easiest and best

to install when making sharp bends at the

enclosure or equipment. It has all of the

advantages of the straight fitting with only one

screw to tighten, except in the larger sizes where

there are two. A peep hole on top provides for easy

inspection of the ABC bushing. Narrow design

makes it easy to install fittings in adjacent

knockouts.

CONFITMRO_EN_ALL.pdf 116 11/28/2011 11:05:40 AM

117

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Squeeze Fittings

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

252 .531 .437 5/16” 3/8” 13/16 25/32 11/32

253-TB†.585 .455 3/8” 1/2” 31/32 1-13/64 5/8

254-C†.938 .812 1/2” 1/2” 1-7/32 1-3/8 13/32

255 1.094 .938 3/4” 3/4” 1-1/4 1-17/32 7/16

256 1.375 1.250 1” 1” 1-19/32 1-5/8 1/2

257 1.656 1.500 1-1/4” 1-1/4” 1-7/8 1-23/32 17/32

258 1.875 1.688 1-1/2” 1-1/2” 2-1/4 1-7/16 9/16

259 2.500 2.313 2” 2” 2-31/32 2-5/8 11/16

249 3.062 2.812 2-1/2” 2-1/2” 3-5/16 2-11/16 3/4

277 3.563 3.312 3” 3” 3-13/16 2-7/8 3/4

†U.L. Listed for armoured cable only. Fitting material steel.

Squeeze Fittings—90° Angle

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

266-C* .656 .406 3/8” 1/2” 1-1/2 1-13/32 1-7/16

272†.812 .688 3/8” 1/2” 1-9/16 1-7/8 1-9/16

268-C .937 .813 1/2” 1/2” 1-11/16 1-13/16 1-7/8

279 1.000 .875 3/4” 3/4” 1-13/16 2-1/16 1-13/16

270 1.125 1.000 3/4” 3/4” 1-7/8 1-3/4 1-13/16

273-TB 1.406 1.187 1” 1” 2-3/8 2-7/32 2-7/16

274‡1.656 1.375 1-1/4” 1-1/4” 3 2-9/16 2-7/8

275‡1.875 1.625 1-1/2” 1-1/2” 3-7/32 3-1/16 4-1/8

276‡2.500 2.125 2” 2” 4-5/8 3-5/8 4-7/8

†U.L. Listed for armoured cable only.

‡U.L. Listed for flexible metal conduit only.

Squeeze Fittings—45° Angle

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

265* .656 .406 3/8” 1/2” 1-7/16 1-5/32 1-1/8

267 .937 .813 1/2” 1/2” 1-3/16 1/2 1-1/4

269 1.125 1.000 3/4” 3/4” 1-7/8 17/32 1-9/16

T&B squeeze fittings will fit every size of

armoured cable, leaded cable and flexible

conduit. Malleable iron or steel construction.

Part No. 253-TB is steel.

3/8” and 1/2” sizes made in steel. Cap lifts off by

simply loosening screws part way. Only two

screws to tighten. 3/4” size and larger made

of malleable iron.

3/8” and 1/2” sizes made in steel. Cap lifts off by

simply loosening screws part way.

CONFITMRO_EN_ALL.pdf 117 11/28/2011 11:05:40 AM

118

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Two-Screw Fittings

Cable Opening (in.) Trade K.O. Dimensions (in.)

Cat. No. max. min. Size Size A B C

3301-C* .656 .250 3/8” 1/2” 5/8 1-5/16 1-3/16

3312-C .937 .500 1/2” 1/2” 5/8 1-5/16 1-3/16

* U.L. Listed for armoured cable only.

Duplex Clamp Fitting

Dimensions (in.)

Cat. No. K.O. Size A B

291-C 1/2” 1-13/32” 1-11/16”

U.L. Listed as grounding means under NEC 350-5.

Adaptor—EMT to Flex

Dimensions (in.)

Cat. No. K.O. Size A B C

503-TB 1/2” - 1/2” 1-21/32 1-3/16 1-7/8

504 3/4” - 3/4” 1-25/32 1-7/16 2-1/8

505-TB 1” - 1” 2-1/32 2-1/16 2-5/8

Formed steel body with carefully round

bushing. The armour gripping saddle stays

open by itself when cable is being inserted.

Malleable iron.

For nonmetallic and armoured cable.

Tite-Bite ®fitting design holds flexible metal

cable firmly in place with a single screw rather

than two screws.

C (max)

CONFITMRO_EN_ALL.pdf 118 11/28/2011 11:05:40 AM

119

T&B Conduit Fittings

Armoured Cable and Flexible Metal Conduit Fittings

Combination Coupling

Size Dimension (in.)

Cat. No. Flex to EMT A B C

449C 3/8” - 1/2” 1-21/32 1-11/32 15/16

Cable opening: max. .656, min. .250

Anti-Short Bushing

Cat. No. Size

390 14-2, 14-3, 12-2

391 14-4, 12-3, 6-1, and 4-1

392 12-4, 10-2, 10-3 and 2-1

393 10-4, 8-2, 8-3, and 1-1

394 8-4, 6-2, 6-3, 4-2, 4-3, and 6-4

Colorized

Temperature Rating: 240°F

U.L. not applicable.

Strap

Cat. No. Bolt Hole Dia. Size

65C .265” 3/8” Flex

A one piece fitting that couples 3/8” flexible

metal conduit to 1/2” electrical metallic tubing

(EMT)

Anti-short bushings are made of smooth plastic,

and designed to protect conductor insulation from

rough edges of armoured cable and flexible metal

conduit.

C A B

15/16 15/16

1-21/32 1-11/32

CONFITMRO_EN_ALL.pdf 119 11/28/2011 11:05:41 AM

120

T&B Conduit Fittings

Nonmetallic Sheathed Cable Fittings

Specifications — Nonmetallic (NM) Sheathed Cable

Ref. CEC Rule 12-500

Canadian Electrical Code 2009 Part I,

defines Nonmetallic Sheathed Cable as,

“A factory assembly of two or more

insulated conductors having an outer

sheath of moisture resistant, flame

retardant, nonmetallic material.”

Nonmetallic sheathed cable is

constructed of insulated conductors

(14 to 2 AWG copper), and an outer

nonmetallic sheath classified as Types

NMD90, NMW and NMWU.

Nonmetallic sheathed cable is

provided with bare bonding conductor.

Nonmetallic sheathed cable is rated for

90°C service with voltage limitation of

300 volts.

Type NMW and NMWU have a flame

retardant, moisture resistant sheath.

Type NMD90, NMW and NMWU

applications are described in Table 19

of CEC 2009 Part I.

Nonmetallic sheathed cable is

permitted by code to be used exposed

or concealed in one, two or multifamily

dwellings or other structures not

exceeding three floors. Use of Type

NMD90 cable is restricted to dry locations.

Nonmetallic sheathed cables are not

permitted to be used as a service

conductor. Nonmetallic sheathed cables

are also prohibited in hazardous locations.

NM cables need to be secured in

place by suitable means so as not to

injure the cable. Adequate protection

for cable is also required when run is

exposed, through joists or rafters,

through floors, in unfinished basements

and accessible attics.

NM cables shall be protected from

physical damage when it passes through

factory or field punched, cut or drilled

holes in metal members. A bushing or

grommet firmly secured in place is

recommended (CEC Rule 12-516).

Please refer to the following for further

details and complete information:

1. U.L. 719, ANSI C33.56 ..........Safety

Standards for Nonmetallic Sheathed

Cable

2. U.L. 514.................................Safety

Standards for Outlet Boxes and

Fittings

3. NEMA FB-1… ..Standards Publication:

Fittings and Supports for Conduit

and Cable Assemblies

4. CEC Section 12-500..............Wiring

methods (Nonmetallic Sheathed

Cable)

5. CSA C22.2 No. 48… .............Safety

Standards for Nonmetallic Sheathed

Cable

6. CSA C22.2 No. 18… .............Safety

Standards for Outlet Boxes,

Conduit Boxes and Fittings

Please Note

The excerpts and other material herein, whether relating to the Canadian Electrical

Code 2009 Part I, the Underwriters Laboratories, Inc. listing, to industry practice or

otherwise, is not intended to provide all relevant information required for use and

installation. Reference to original or primary source material and data is mandatory

before any application or use is made of the product.

CONFITMRO_EN_ALL.pdf 120 11/28/2011 11:05:41 AM

121

T&B Conduit Fittings

Nonmetallic Sheathed Cable Fittings

Suggested Specifications for Nonmetallic Sheathed Cable

• Where nonmetallic sheathed cable

or flexible cord terminates into a

threaded or threadless opening,

terminating fittings used shall be

approved for the purpose by nationally

recognized laboratory, inspection agency

or product evaluation organization.

• Terminating fittings shall be of

malleable iron, steel, or thermoplastic

construction designed to provide

adequate strain relief and positively

prevent damage to jacket or

conductor insulation such as series

3300 or 3302M manufactured by

Thomas & Betts.

Ferrous metal fittings shall be electro-zinc

plated inside and outside including

threads and bushed with a nylon

insulated throat.

Thermoplastic material used for

fitting construction shall be of

high impact strength suitable for

105°C/221°F service with a U.L.

flammability rating of 94V-1.

• Where nonmetallic sheathed cable

passes through either factory or field

punched, cut or drilled holes

in metallic members, the cable

shall be protected by thermoplastic

bushing such as series 3210

manufactured by Thomas & Betts.

Bushing shall be firmly secured in

opening. Nylon bushed metallic

fittings such as Thomas & Betts series

1942 may be substituted

as required.

Series 3302M

Nonmetallic Sheathed Cable

and Flexible Cord Fittings

(Steel)

Series 3300

Nonmetallic Sheathed Cable

and Flexible Cord Fittings

(All Plastic)

Series 3210

Knockout Bushings

Series 1942

Insulated Nipples

CONFITMRO_EN_ALL.pdf 121 11/28/2011 11:05:41 AM

122

T&B Conduit Fittings

Nonmetallic Sheathed Cable Fittings

Nonmetallic Sheathed Cable & Flexible Cord Fittings (Steel)

Application

• To connect nonmetallic sheathed

cable and flexible cord to a box or an

enclosure.

Features

• Rugged all steel/malleable iron

construction (A).

• Rounded cable clamp grip provides

superior mechanical holding power

without damaging conductor

insulation or outer jacket (B).

• Clamp designed to cover body

opening for a neat and safe

installation.

• Screws thread into clamp and not

body; screw heads are snug with

body and ends of screws do not

project beyond the body (C).

• Insulator firmly secured in place

protects conductors and reduces

wire pulling effort; protects threads

from damage during handling (D).

• Locknut designed to secure fitting

to a box or enclosure; will not vibrate

loose.

Standard Material

Body 1/2” thru 1” Steel; 1-1/4”

thru 2” Malleable Iron

Clamp 1/2” thru 1-1/4” Steel; 1-

1/4”

thru 2” Malleable Iron

Locknut All Steel

Insulator Thermoplastic

Standard Finish

All steel and malleable iron parts—

Electro Zinc Plated & Chromate

Coated

Range

• Hub Size 1/2” thru 2” Hubs

provided with straight

pipe threads (NPS.)

• Cable 2 #14 thru 4 #4 Type

• Cable Outside Diameter

0.250” to 1.150”

Conformity

U.L. 514B

CSA C22.2 No. 18.3

NFPA 70-2008 (ANSI)

NEMA FB-1

Federal Standard H-28 (Threads)

3302M Series

Nonmetallic Sheathed

Cable Fitting

Typical Installation

(Flexible Cord)

Typical Installation

(NM-Sheathed Cable)

(D)

Locknut Box or

Enclosure Wall

(A)

(B)

(C)

CONFITMRO_EN_ALL.pdf 122 11/28/2011 11:05:41 AM

123

T&B Conduit Fittings

Nonmetallic Sheathed Cable Fittings

Steel or malleable iron.

Rounded cable grip and smooth bushing protect

the cable sheath and wire insulation. Since

saddle is threaded, screws do not travel or

extend beyond the fitting body as it is clamped

to the cable. An extra lip on the saddle closes

the unused part of the fitting opening.

Two-Screw Fittings

U.L. Listed & CSA Certified U.L. Listed & CSA

Cat. No. K.O. for the following Single (1) Certified for the following Dimensions (in.) Cable Opening

Noninsulated Insulated Size and Pairs of (2) NM & NMC Cable Service Entrance Cables A B C max. min.

3302* 3302M-C 1/2” (1) 2#14, 2#12, 2#10, 3#14, 2#12 thru 2#4, 3#12, 3#10 31/32” 1-3/8” 1” .590 .250

3#12, 3#10, (2) 2#14, 2#12

3303-C 3303M 3/4” (1) 2#8, 2#6, 3#8 2#8 thru 2#1/0, 3#8, 3#6, 1-1/4” 1-5/8” 1-3/16” .750 .530

(2) 2#12, 2#10, 2#8, 3#14 2#6 + #8 GND

(1) 3#8, 3#6, 3#4 2#1, 2#1/0, 3#6 thru 3#2,

3304 3304M 1” (2) 2#8, 3#10 2#4 + #6 GND, 2#3 + #5 1-15/32”1-7/8” 1-1/4” .990 .690

GND, 2#2 + #4 GND

(1) 3#8, 3#6, 3#4 3#2 thru 3#2/0, 2#1 + #3

3305 3305M 1-1/4” (2) 2#8, 2#6, 2#4, 3#8 GND, 2#1/0 + #2 GND, 1-15/16”2-7/32”1-9/32” 1.320 .850

2#2/0 + #1 GND

3306 3306M 1-1/2” (1) 3#4 3#3/0, 3#4/0, 2#3/0 + #1/0 2-5/32”2-21/32”1-5/8” 1.515 .930

GND, 2#4/0 + #2/0 GND

3307 3307M 2” Max. 1.98”, Min. 1.15”

3308†— 2-1/2” Max. 2.38”, Min. 1.5”

3309†— 3” Max. 2.88”, Min. 1.75” — 2-25/32”3-5/16”1-29/32” 1.980 1.150

3310†— 3-1/2” Max. 3.38”, Min. 2.25”

3311†— 4” Max. 3.88”, Min. 2.5”

* U.L. Listed for use with rubber and thermoplastic flexible cords (both single and multiple cords and 2 oval cables).

U.L. Listed for multiple cords and cables.

CONFITMRO_EN_ALL.pdf 123 11/28/2011 11:05:41 AM

124

T&B Conduit Fittings

Nonmetallic Sheathed Cable Fittings

Application

• To connect nonmetallic sheathed

cable and flexible cord to a box or an

enclosure.

Features

• Provides strain relief by partially

deflecting cable (A); therefore:

(1) Fitting will not damage outer

covering or jacket of cable, or

conductor insulation; designed to

give safe trouble-free installation.

(2) Holding power and cable strain

relief are not effected by surface

finish of outer covering or cable

jacket.

(3) Fitting provides superior holding

power far in excess of listing

agency requirements.

• Snap-in one piece design;

accommodates variation in knockout

dimensions, saves installation time

(B).

• All high impact thermoplastic

construction provides:

(1) Insulated throat; conductors are

protected from abrasion.

(2) Improved dielectric strength, and

elimination of potential shorts.

(3) Corrosion resistance.

• Wide range—reduces inventories

• Fitting may be pre-installed in box

K.O., or on cable.

Standard Material

All high impact thermoplastic—U.L.

Class 94V-1 suitable for 105°C

application.

Standard Finish

As Molded

Listing/Certification

Cat. No. 3201, 3350 for factory

installation

Conformity

U.L. 514B

CSA C22.2 No.18.3

NFPA 70-2008 (ANSI)

Range

Knockout

Cat. No. Size Cable/ Cord Range

3300 1/2” 10-2, 12-2 & 14-2 type

NM Cable .125” to .300”

outside diameter cord

10-3, 12-3, 14-3, 10-

2, 12-2, 14-2 Type NM

Cable; also multiple

3201 & 1/2” (2) 12-2 and 14-2

3350 Type NM Cable;

.300” to .600” outside

diameter cord 8-3 and

6-3 type

3202 3/4” NM cables; also

Multiple (2) 14-3 and

10-2 Type NM Cable;

.500” to .850” outside

diameter cord

Box or

Enclosure Wall

(C)

Cable or Cord

(A)

(B)

1. Remove sheath from end

of cable (4” or more as

required). Insert cable through

fitting as shown (Cable under

button).

Nonmetallic Sheathed Cable and Flexible Cord Fittings

(All Plastic)

Typical Installation

3300 Series

4. Snap fitting into knockout

box. If desired this step

can be done prior to Step 1.

5. To remove from knockout box

depress ears.

6. To remove from cable cut

fitting as shown

2. Insert button into cavity.

3. With grooved pliers, or

parallel jaw type pliers

(commercially available)

squeeze button into cord or

wires as far into fitting body

as possible.

Note: It may be necessary to re-

adjust pliers to insure

button is properly installed.

CONFITMRO_EN_ALL.pdf 124 11/28/2011 11:05:41 AM

125

T&B Conduit Fittings

Nonmetallic Sheathed Cable Fittings

Figure 1

All Plastic Fitting for NM Cable and Flexible Cord

K.O. Dimensions (in.) Max. Thk.

Cat. No. Size Range Size Fig. A B C D E Enclosure H

3300 For use with 10-2, 12-2

and 14-2 NM cables;

18-2 and 18-3 SJ

and SJO cords and 1/2” 2 1-1/32 15/16 3/8 .880 .795 .080 5/16

x 9/16

18-2 SV, SVO, SJT

and SJTO cords, single

or multiple; cord capacity

.125-.300 diameter

3350 For use with 10-3, 12-3,

14-3, 10-2, 12-2,

4-2 NM cables; multiple

(2) 12-2 and 14-2 N 1/2” 1 1-11/32 1 7/16 .880 .795 .080

21/32 dia.

M cables; single and

multiple flexible cords

in wire range .300 in. to .600 in.

3202 For use with 8-3 and

6-3 NM cables; (2) 14-3,

14-2, 12-2 and 10-2 NM

cables; single and multiple 3/4” 1 1-1/2 1-5/16 7/16 1.100 1.005 .090 7/8 dia.

flexible cords in wire range

.500 in. to .850 in.

Temperature Rating: 105°C

Snap captive locking wedge into fitting’s cavity.

Press locking wedge into cavity which locks

onto cable.

Hole

Size

High impact thermoplastic. U.L. 94-V1.

Features push-in design. Captive locking wedge

secures cable with single squeeze of standard

electrician’s pliers. Provides excellent insulation,

strain-relief and high pull-out value.

Cat. No. 3201 is ideal for multiple flexible cords

and cable.

Figure 2

Hole Size

CONFITMRO_EN_ALL.pdf 125 11/28/2011 11:05:41 AM

126

T&B Conduit Fittings

Nonmetallic Sheathed Cable Fittings

Snap-in Fitting for Flexible Metal Conduit

Cat. No. Conduit Size K.O. Size A B C

100TB 3/8” 1/2” 27/32 1-13/32 1-31/32

100BP 3/8” 1/2” 27/32 1-13/32 1-31/32

Temperature Rating: 105°C

U.L. 94-V1

Swivel Tray Clamp

Conduit

Cat. No. Size

6209 1/2”-3/4”

6211 1”-1-1/4”

6214 1-1/2”-2”

6216 2-1/2”-3”

6218 3-1/2”-4”

Cable Tray Clamp

Conduit

Cat. No. Size

6210 1/2”-3/4”

6212 1”-1-1/4”

No locknut required. No special tools required.

High impact thermoplastic with steel insert.

Swivel cable tray clamps for aluminum and

steel trays with regular or reinforced flanges.

• Serrations and biting teeth on clamping

saddle provides a high quality bond between

conduit and clamp

• 1/2” to 6” sizes that can be clamped to any

position in a 90° arc

• Hardened steel screws bite into tray and

provide positive bond

• Malleable iron hub and steel u-bolt accepts

conduit from any angle

CONFITMRO_EN_ALL.pdf 126 11/28/2011 11:05:42 AM

127

T&B Conduit Fittings

Liquatite®Flexible Conduit— Application Guide

High Listed for Low Accepts Std.

Conduit Metal Plastic*** Mech. Direct Halogen Fire Liquidtight Self EMI/RFI

Type Page Flexibility* Used** Used Strength Burial Free Hazard Fittings Extinguish Shielding Approval

TYPE-LT 129 B S P

pp.92-94

JIC

TYPE-LOR 130 B S P

pp.92-94

JIC

TYPE-EF 130 B S P

pp.92-94

JIC

TYPE-LA 131 C S P X X

pp.92-94

TYPE-CBLA 132 C S P X X

pp.92-94

TYPE-CSA 133 C S P X

pp.92-94

TYPE-ATLA 134 C S P X X

pp.92-94

TYPE-AT 135 B S P

pp.92-94

TYPE-ATX 135 B S T X

p.91

TYPE-ALT 136 C A P

pp.92-94

TYPE-CEA 137 C S U X X

pp.92-94

TYPE-ACEA 138 C A U X X

pp.92-94

TYPE-ZHLA 139 C S U X X X X

pp.92-94

TYPE-LAS 140 C S P X X

pp.92-94

TYPE-EMS 141 C B P

pp.92-94

TYPE-EMSP 141 C B P

pp.92-94

TYPE-BR 142 C S X

pp.115-119

-3/8

TYPE-ABR 143 C A

pp.115-119

-3/8

TYPE-USL 144 B S

pp.115-119

TYPE-SL 144 A, B S

pp.115-119

TYPE-VJC 145 A, B S P

pp.115-119

TYPE-UG 145 C S

pp.115-119

TYPE-LNM-P 146 A P

p.102

TYPE-NMC 147 C P X X

pp.108-110

TYPE-NMT 147 A P X

pp.108-110

TYPE-CL 148 C N X X

p.150

TYPE-CLL 148 B N X

p.150

TYPE-CCG 149 B N X

p.150

TYPE-CLR 149 A N X

p.150

TYPE-CLFR 149 C N X X X

p.150

*** P=PVC

U=Pu

T=TPR

N=Nylon

* A=Continuous flexing

B= Small bend radius

C=Flexible

D=Pliable (static)

** S=Steel

A=Aluminum

B= Bronze

CONFITMRO_EN_ALL.pdf 127 11/28/2011 11:05:42 AM

128

T&B Conduit Fittings

Liquatite®Flexible Conduit— Application Guide

Temperature Range

General

Chemical Resistance

Conduit °C -60 -40 -20 0 +50 +60 +75 +80 +90 +105 +150 See chart on page 156

Type °F -76 -40 -4 +32 +122 +140 +167 +176 +194 +221 +302 Oils Acids

TYPE-LT III I IIIIII X X

TYPE-LOR III I IIIIII X X

TYPE-EF III I IIIIII X X

TYPE-LA III I IIIIII X X

TYPE-CBLA III I IIIIII X X

TYPE-CSA III I IIIIII X X

TYPE-ATLA III I IIIIII X X

TYPE-AT III I IIIIII X X

TYPE-ATX III I IIIIII X

TYPE-ALT III I IIIIII X X

TYPE-CEA III I IIIIII X

TYPE-ACEA III I IIIIII X

TYPE-ZHLA III I IIIIII X

TYPE-LAS III I IIIIII X X

TYPE-EMS III I IIIIII X X

TYPE-EMSP III I IIIIII X X

TYPE-BR III I IIIIII

TYPE-ABR III I IIIIII

TYPE-USL III I IIIIII

TYPE-SL III I IIIIII

TYPE-VJC III I IIIIII X X

TYPE-UG III I IIIIII

TYPE-LNM-P III I IIIIII X X

TYPE-NMC III I IIIIII X X

TYPE-NMT III I IIIIII X X

TYPE-CL III I IIIIII X

TYPE-CLL III I IIIIII X

TYPE-CCG III I IIIIII X

TYPE-CLR III I IIIIII X

TYPE-CLFR III I IIIIII X

CONFITMRO_EN_ALL.pdf 128 11/28/2011 11:05:42 AM

129

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type LT

Carton Reel Reel

Trade Size Content* Content* Content* Inside Bend Radius Weight

(in.) Cat. No. (m) Cat No. (m) Cat No. (m) in. (mm) kg/30m

1/4 LT025-75 75 ---- 1.0 (25.4) 8

5/16 LT032-75 75 ---- 1.0 (25.4) 8

3/8 LT038-30 30 LT038-150 150 LT038-300 300 1.5 (38.1) 9

1/2 LT050-30 30 LT050-150 150 LT050-300 300 2.0 (50.8) 11

3/4 LT075-30 30 LT075-150 150 LT075-300 300 2.5 (63.5) 15

1LT100-30 30 LT100-120 120 -3.0 (76.2) 24

1-1/4 LT125-15 15 LT125-75 75 -- 3.5 (88.9) 31

1-1/2 LT150-15 15 LT150-45 45 -- 4.5 (114.3) 40

2LT200-15 15 LT200-30 30 -5.5 (139.7) 53

2-1/2 LT250-8 8LT250-80 80 -- 8.0 (203.2) 76

3-1/2 LT350-8 8LT350-50 50 -- 11.0 (279.4) 132

4LT400-8 8LT400-30 30 -- 12.0 (304.8) 156

5LT500-8 8---- 17.5 (444.5) 212

6LT600-8 8---- 22.5 (571.5) 259

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Typ e LT

A general purpose, flexible liquidtight

steel conduit designed for a variety of

installations requiring motion, vibration

and bending. It offers good mechanical

and moisture protection to enclosed

conductors.

Construction

The flexible inner core is made from a

spiral wound strip of corrosion resistant

plating steel. The 1/4 through 2 inch

trade sizes are squarelock formed and,

with the exception of the 1/4 inch size,

contain a nylon cord packing within the

convolutions.

The larger sizes are constructed with a

fully interlocked strip to add strength and to

prevent unraveling.

A flexible yet durable PVC jacket

is extruded over this core creating a liquid-

tight conduit resistant to most oils, acids

and vapors present in industrial

environments.

Refer to the Conduit — Chemical

Resistance Chart beginning on p.158.

Applications

This conduit is used extensively in the

machine tool and other industrial

environments where flexibility is

necessary for installation and

maintenance or where vibration and

movement must be absorbed. The inherent

sunlight resistance of PVC enables this

product to be used in outdoor

applications. Compatible with

standard liquidtight fittings. The

construction of this conduit conforms to,

and is suitable for use with Sections 16 &

17.7 of the Electrical Standard for

Industrial Machinery (ANSI/NFPA-79).

Working Temperatures

-20°C to 80°C

Listing / Certification

JIC — manufactured in accordance with

the dimensions and specifications as

outlined by the Joint Industrial Council

Standard for Mass Production Equipment

and Machine Tools.

Standard Colours

Machine tool grey and black. Other

colours available upon request. Part

numbers listed designate grey jacket.

Interlock

2-1/2 ” -6”

Squarelock with Filler

5/16” - 2”

JIC

CONFITMRO_EN_ALL.pdf 129 11/28/2011 11:05:43 AM

130

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type LOR

This product is offered as a non-UL oil-

resistant conduit that incorporates a

high quality PVC jacket.

Applications

The LOR is ideally used in situations

where a UL listing or CSA certification

is not a factor but where a flexible

conduit must withstand exposure to

many harsh chemicals, oils, UV, etc.

This conduit conforms to Section 17.7

of the Electrical Standard for Industrial

Machinery. (ANSI/NFPA-79) Compatible

with Standard Liquidtight Fittings.

Working Temperatures

-20°C to 60°C intermitting to 90°C

Standard Colours

Machine tool grey and black. Other

colours available upon request. Part

numbers listed designate grey jacket.

Note

For a UL listed version, consult your

Regional Sales Office for Type LA/LOR.

Trade Carton Carton Carton Inside

Size Content* Content* Content* Bend Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) Kg/30m

3/8 LOR038-30 30 LOR038-150 150 LOR038-300 300 2.0 (50.8) 19

1/2 LOR050-50 30 LOR050-150 150 LOR050-300 300 2.5 (63.5) 11

3/4 LOR075-30 30 LOR075-150 150 LOR075-300 300 3.0 (76.2) 15

1LOR100-30 30 LOR100-120 120 -- 4.0 (101.6) 24

1-1/4 LOR125-15 15 LOR125-60 60 -- 4.5 (114.3) 31

1-1/2 LOR150-15 15 ---- 5.5 (139.7) 40

2LOR200-15 15 ---- 7.0 (177.8) 53

2-1/2 LOR250-8 8---- 9.5 (241.3) 76

3LOR300-8 8---- 11.5 (292.1) 118

3-1/2 LOR350-8 8---- 13.0 (330.2) 132

4LOR400-8 8---- 14.0 (356.6) 156

5LOR500-8 8---- 20.0 (508.0) 221

6LOR600-8 8---- 22.5 (571.5) 259

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type EF

Typ e EF

This flexible liquidtight conduit is a

competitive grade version of our Type LT. It

conforms to both the JIC standards for

dimensions and general construction,

and to Section 17.7 of the Electrical

Standard for Industrial Machinery

(ANSI/NFPA-79).

Construction

The flexible inner core is constructed

from a helically formed strip of corrosion

resistant steel. A liquidtight PVC jacket is

then extruded over the core.

Applications

General installations requiring some

movement and protection for contained

conductors. Forms a liquidtight system

when installed with standard fittings for

use indoors or out.

Working Temperatures

-20°C to 80°C

Standard Colour

Machine tool grey

Trade Carton Carton Carton Inside

Size Content* Content* Content* Bend Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 EF038-30 30 EF038-150 150 EF038-300 300 1.5 (38.1) 9

1/2 EF050-30 30 EF050-150 150 EF050-300 300 2.0 (50.8) 11

3/4 EF075-30 30 EF075-150 150 EF075-300 300 3.0 (63.5) 14

1EF100-30 30 EF100-120 120 -- 3.0 (76.2) 20

1-1/4 EF125-15 15 EF125-75 75 -- 3.5 (88.9) 25

1-1/2 EF150-15 15 EF150-45 45 -- 4.5 (114.3) 41

2EF200-15 15 EF200-30 30 -- 5.5 (139.7) 5

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

JIC

130-135-e.pdf 1 1/23/2012 2:18:27 PM

131

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type LA

Type

A flexible liquidtight steel conduit which

is both listed UL and certified CSA. It

offers outstanding protection against wet,

oily conditions and is permitted for use in

exposed or concealed locations.

Construction

The flexible inner core is made from

a spiral wound strip of heavy gauge,

corrosion resistant, hot-dipped galvanized

steel. The 3/8 through 1-1/4 inch trade

sizes are square lock formed and include

an integral bonding strip of copper that is

enclosed within the convolutions throug-

hout its entire length. The 1-1/2 through

4 inch trade sizes are designed with a fully

interlocked strip.

The liquidtight jacketing material is

of a high quality, rugged, flame retardant

flexible PVC compound which resists

oils, mild acids and exposure to sunlight.

For further information, refer to the

Conduit — Chemical Resistance chart

beginning on p. 158.

Applications

This conduit is intended for installation

with Rule 12-1300 of Canadian

Electrical Code (CEC) Part I 2009.

The use of a separate bonding

conductor is mandatory in accordance

with CEC Rule 12-1306 for Ordinary

Locations.

The use of Liquidtight Flexible Conduit

with sign and Outline Lighting are in

accordance with CEC Rule 34-400 (2).

Listed and marked for direct burial

and in poured concrete.

For containment of 600-volt and

lower potential circuits

Sunlight resistant

Working Temperatures

-20°C to 60°C intermitting to 90°C

Listing / Certification

Listed. Conforms to UL Standard

ANSI/UL-360

for Liquidtight Flexible

Steel Conduit.

Certified. Conforms

to CSA 22.2

No. 56 for use per CEC C22.1

Section 12-1300.

Standard Colours

Machine tool grey, and black. Other

colours available upon request. Blue

is commonly used for computer room

installations. See TYPE CBLA on p.132.

Squarelock with filler

3/8” - 1-1/4”

Interlock

1-1/2” - 4”

Carton Reel Reel Inside Bend

Trade Size Content* Content* Content* Radius Weight

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 LA038-30 30 LA038-150 150 LA038-300 300 2.0 (50.8) 13

1/2 LA050-30 30 LA050-150 150 LA050-300 300 3.0 (76.2) 15

3/4 LA075-30 30 LA075-150 150 LA075-300 300 4.2 (106.7) 24

1LA100-30 30 LA100-120 120 -- 5.5 (139.7) 37

1-1/4 LA125-15 15 LA125-60 60 -- 7.0 (177.8) 46

1-1/2 LA150-15 15 LA150-45 45 -- 4.5 (114.3) 47

2LA200-15 15 LA200-30 30 -- 6.0 (152.4) 66

2-1/2 LA250-8 8LA250-80 80 -- 8.0 (203.2) 87

3LA300-8 8LA300-50 50 -- 10.0 (254.0) 114

3-1/2 LA350-8 8LA350-50 50 -- 11.0 (279.4) 140

4LA400-8 8LA400-30 30 -- 12.0 (304.8) 154

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

130-135-e.pdf 2 1/23/2012 2:18:28 PM

132

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type CBLA — Computer Blue

Carton Reel Reel Inside Bend

Trade Size Content* Content* Content* Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 CBLA038-30 30 CBLA038-150 150 CBLA038-300 300 2.0 (50.8) 13

1/2 CBLA050-30 30 CBLA050-150 150 CBLA050-300 300 3.0 (76.2) 15

3/4 CBLA075-30 30 CBLA075-150 150 CBLA075-300 300 4.2 (106.7) 24

1CBLA100-30 30 CBLA100-120 120 -- 5.5 (139.7) 37

1-1/4 CBLA125-15 15 CBLA125-60 60 -- 7.0 (177.8) 46

1-1/2 CBLA150-15 15 CBLA150-45 45 -- 4.5 (114.3) 47

2CBLA200-15 15 CBLA200-30 30 -- 6.0 (152.4) 66

2-1/2 CBLA250-8 8CBLA250-80 80 -- 8.0 (203.2) 87

3CBLA300-8 8CBLA300-50 50 -- 10.0 (254.0) 114

3-1/2 CBLA350-8 8CBLA350-50 50 -- 11.0 (279.4) 140

4CBLA400-8 8CBLA400-30 30 -- 12.0 (304.8) 154

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type CBLA

Computer Blue LA is a liquidtight

flexible steel conduit commonly used

for computer room installations. The

blue jacket colour easily identifies

circuitry for computer power wiring.

Construction

CBLA has a flexible inner core made

from a spiral wound strip of heavy

gauge, hot-dipped galvanized steel.

The 3/8 through 1-1/4 inch trade sizes

contain an integral bonding strip of

copper. The 1-1/2 and larger sizes are

designed with a fully interlocked strip.

The jacketing material is a rugged

flame retardant flexible blue PVC. For

installations which do not allow the use of

PVC, see TYPE ZHLA on P. 139.

Applications

Listed and marked for direct burial and

in poured concrete.

Working Temperatures

-20°C to 60°C

Listing / Certification

Listed. Conforms to UL

Standard ANSI/UL-360

for

Liquidtight Flexible Steel Conduit.

Certified. Conforms

to CSA 22.2

No. 56 for use per CEC C22.1

Section 12-1300.

130-135-e.pdf 3 1/23/2012 2:18:28 PM

133

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type CSA

Carton Reel Reel Inside Bend

Trade Size Content* Content* Content* Radius Weight

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 CSA038-30 30 CSA038-150 150 CSA038-300 300 2.0 (50.8) 11

1/2 CSA050-30 30 CSA050-150 150 CSA050-300 300 3.0 (76.2) 16

3/4 CSA075-15 15 ----

3/4 CSA075-30 30 CSA075-150 150 CSA075-300 300 4.0 (101.6) 24

1CSA100-30 30 CSA100-120 --- 5.0 (127.0) 27

1-1/4 CSA125-15 15 CSA125-60 60 -- 6.2 (157.5) 39

1-1/2 CSA150-15 15 CSA150-45 45 -- 4.5 (114.3) 55

2CSA200-15 15 CSA200-30 30 -- 6.0 (152.4) 70

2-1/2 CSA250-8 8 -- -- 8.0 (203.2) 93

3CSA300-8 8---- 10.0 (254.0) 120

4CSA400-8 8 ---- 12.0 (304.8) 181

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type CSA

This flexible liquidtight steel conduit is

certified CSA. Its design and function is

similar to that of type LA except that it

cannot be used as a ground return path

per CEC. It also offers a wider operating

temperature range.

Construction

The flexible inner core is made from a

spiral wound strip of heavy gauge,

corrosion resistant, hot-dipped

galvanized steel. The 3/8 through 1-1/4

inch trade sizes are cord packed.

The durable PVC flame retardant jacket

is designed for good flexibility and impact

resistance at low temperatures.

Applications

This conduit is intended for use according

to CEC as described in section 12-

1300 for dry, damp or wet locations

where flexibility is necessary.

This conduit is intended for installation

with Rule 12-1300 of Canadian

Electrical Code (CEC) Part I 2009.

The use of a separate bonding

conductor is mandatory in accordance

with CEC Rule 12-1306 for Ordinary

Locations.

The use of Liquidtight Flexible Conduit

with sign and Outline Lighting are in

accordance with CEC Rule 34-400 (2).

Working Temperatures

-40°C to 75°C

Listing / Certification

Certified. Conforms to CSA

Standard C22.2, No. 56. Flame Test

Rating FT-4 per CSA Standard

C22.2, No. 0.3.

Standard Colour

Black

130-135-e.pdf 4 1/23/2012 2:18:28 PM

134

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type ATLA — All Temperature

Carton Reel Reel Inside Bend

Trade Size Content* Content* Content* Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 ATLA038-30 30 ATLA038-150 150 ATLA038-300 300 2.0 (50.8) 13

1/2 ATLA050-30 30 ATLA050-150 150 ATLA050-300 300 3.0 (76.2) 15

3/4 ATLA075-30 30 ATLA075-150 150 ATLA075-300 300 4.2 (106.7) 24

1ATLA100-30 30 ATLA100-120 120 -- 5.5 (139.7) 37

1-1/4 ATLA125-15 15 ATLA125-60 60 -- 7.0 (177.8) 46

1-1/2 ATLA150-15 15 ATLA150-45 45 -- 4.5 (114.3) 47

2ATLA200-15 15 ATLA200-30 30 -- 6.0 (152.4) 66

2-1/2 ATLA250-8** 8---- 8.0 (203.2) 87

3ATLA300-8** 8 ---- 10.0 (254.0) 114

3-1/2 ATLA350-8** 8 ---- 11.0 (279.4) 140

4ATLA400-8** 8---- 12.0 (304.8) 154

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

** Not CSA Certified.

Type ATLA

A liquidtight flexible steel conduit

designed specifically for extreme hot or

cold environments. The flexible inner core

is identical to that found in Type LA. The

specially formulated PVC jacket remains

flexible at low temperatures and resists

ageing at elevated temperatures. It is listed

UL and certified CSA.

Construction

ATLA has a flexible inner core made

from a spiral wound strip of heavy

gauge, hot-dipped galvanized steel.

The 3/8 through 1-1/4 inch trade sizes

contain an integral bonding strip of

copper. The 1-1/2 and larger sizes are

designed with a fully interlocked strip.

The jacketing material is a rugged flame

retardant flexible PVC resistant to

weathering, UV, oils and many chemicals.

Refer to the Conduit — Chemical

Resistance Guide beginning on p.158.

Applications

Designed to be used with high

temperature machine tool wiring. Ideal

for outdoor installations in cold

climates.

This conduit is intended for

installation with Rule 12-1300 of

Canadian Electrical Code (CEC) Part I

2002.

The use of a separate bonding

conductor is mandatory in accordance

with CEC Rule 12-1306 for Ordinary

Locations.

The use of Liquidtight Flexible Conduit

with sign and Outline Lighting are in

accordance with CEC Rule 34-400 (2).

- Listed and marked for direct burial

and in poured concrete.

-For containment of 600-volt and

lower potential circuits.

Working Temperatures

-55°C to 105°C Air / 60°C Wet / 70°C Oil

Listing / Certification

Listed. Conforms to UL Standard

ANSI/ UL-360 for Liquidtight

Flexible Steel Conduit.

Certified. Conforms to CSA 22.2

No. 56 for use per the CEC C22.1

Section 12-1300.

Conforms to the requirements of

Section 16 & 17.7 of the ANSI/NFPA-79

Electrical Standard for Industrial

Machinery.

Standard Colour

Machine tool grey

130-135-e.pdf 5 1/23/2012 2:18:28 PM

135

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type AT — High and Low Temperatures

Typ e AT

A flexible steel conduit which uses a

jacketing material specifically designed

for hot or cold environments.

Applications

Type AT is well suited for exposure

to extreme climatic conditions. It is also

widely used on industrial process

equipment such as annealing ovens,

lumber kilns, foundries and refrigeration,

etc. The construction of this conduit

conforms to, and is suitable for use

with Sections 16 & 17.7 of the Electrical

Standard for Industrial Machinery

(ANSI/NFPA-79). Uses standard liquid-

tight fittings.

Working Temperatures

-55°C to 105°C intermitting to 120°C

Standard Colour

Machine tool grey

Note

For a UL listed and CSA certified

version, see TYPE ATLA on p. 134.

Trade Carton Carton Carton Inside

Size Content* Content* Content* Bend radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 AT038-30 30 AT038-150 150 AT038-300 300 1.5 (38.1) 9

1/2 AT050-30 30 AT050-150 150 AT050-300 300 2.0 (50.8) 11

3/4 AT075-30 30 AT075-150 150 AT075-300 300 2.5 (63.5) 15

1AT100-30 30 AT100-120 120 -- 3.0 (76.2) 24

1-1/4 AT125-15 15 AT125-60 60 -- 3.5 (88.9) 31

1-1/2 AT150-15 15 AT150-45 45 -- 4.5 (114.3) 40

2AT200-15 15 AT200-30 30 -- 5.5 (139.7) 53

2-1/2 AT250-8 8---- 8.0 (203.2) 76

3AT300-8 8 ---- 10.0 (254.0) 118

3-1/2 AT350-8 8 ---- 11.0 (279.4) 132

4AT400-8 8 ---- 12.0 (304.8) 156

5AT500-8 8 ---- 17.5 (444.5) 221

6AT600-8 8 ---- 22.5 (571.5) 259

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type ATX — Extreme Temperature

Typ e ATX

A conduit designed to withstand an

extreme temperature range.

Construction

Utilizes the flexibility of our standard LT

core, coupled with the advantage of a

thermoplastic rubber jacket that is

virtually unaffected by temperature

extremes and contains no halogens. The

material has a UL 94-HB flammability

rating.

Applications

Used in situations where there are

concerns of resistance to temperature

exposure. These include heavy outdoor

equipment, boilers and furnaces, etc.

Refer to the Conduit — Chemical

Resistance Guide beginning on p.158.

Working Temperatures

-60°C to 150°C intermitting to 165°C

Standard Colour

Black

Trade Carton Carton Carton Inside

Size Content* Content* Content* Bend radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 ATX038-30 30 ATX038-150 150 ATX038-300 300 1.5 (38.1) 10

1/2 ATX050-30 30 ATX050-150 150 ATX050-300 300 2.0 (50.8) 12

3/4 ATX075-30 30 ATX075-150 150 ATX075-300 300 2.5 (63.5) 18

1ATX100-30 30 ATX100-120 120 -- 3.0 (76.2) 25

1-1/4 ATX125-15 15 ATX125-60 60 -- 3.5 (88.9) 33

1-1/2 ATX150-15 15 ATX150-45 45 -- 4.5 (114.3) 47

2ATX200-15 15 ATX200-30 30 -- 5.5 (139.7) 62

2-1/2 ATX250-8 8---- 8.0 (203.2) 85

3ATX300-8 8---- 10.0 (254.0) 111

4ATX400-8 8---- 12.0 (304.8) 151

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

*New High Temperature Fittings available. Refer to p. 91.

130-135-e.pdf 6 1/23/2012 2:18:28 PM

136

T&B Conduit Fittings

Liquatite®Flexible Conduit — Aluminum

Type ALT — Lightweight Aluminum

Carton Reel Reel Inside

Trade Size Content* Content* Content* Bend Radius Wt.

(in.) Cat. No. (m) Cat No. (m) Cat No. (m) in. (mm) kg/30m

3/8 ALT038-30 30 ALT038-150 150 ALT038-300 300 2.0 (50.8) 5

1/2 ALT050-30 30 ALT050-150 150 ALT050-300 300 2.5 (63.5) 7

3/4 ALT075-30 30 ALT075-150 150 ALT075-300 300 3.0 (76.2) 9

1ALT100-30 30 ALT100-120 120 -- 4.0 (101.6) 13

1-1/4 ALT125-15 15 ALT125-60 60 -- 4.5 (114.3) 18

1-1/2 ALT150-15 15 ALT150-45 45 -- 5.5 (139.7) 25

2ALT200-15 15 ALT200-30 30 -- 7.0 (177.8) 33

2-1/2 ALT250-8 8---- 9.5 (241.3) 47

3ALT300-8 8 ---- 11.5 (292.1) 60

3-1/2 ALT350-8 8 ---- 13.0 (330.2) 74

4ALT400-8 8---- 14.0 (355.6) 81

5ALT500-8 8 ---- 20.0 (508.0) 114

6ALT600-8 8---- 22.5 (571.5) 143

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type ALT

This version of Liquidtight Flexible

Conduit is similar to our standard type

LT but weighs considerably less due to

the use of an aluminum inner core

instead of steel.

Applications

Type ALT is often used where weight or

corrosive atmospheres are an issue. When

comparing identical trade sizes, Type ALT

weighs approximately 37% less than

type LT. Uses standard

liquidtight fittings.

Working Temperatures

-20°C to 80°C

Standard Colours

Machine tool grey and black. Other

colours available upon request. Part

numbers listed designate grey jacket.

CONFITMRO_EN_ALL.pdf 136 11/28/2011 11:05:44 AM

137

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type CEA — Non-Halogen, Low Smoke, Flame Retardant

Carton Carton Minimum Inside

Trade Content* Content* Jacket Bend Radius Wt.

Size Cat. No. (m) Cat. No. (m) Thickness in. (mm) kg/30m

3/8 CEA038-30 30 CEA038-300 300 0.8 1.5 (38.1) 9

1/2 CEA050-30 30 CEA050-300 300 0.8 2.0 (50.8) 11

3/4 CEA075-30 30 CEA075-150 150 0.9 2.5 (63.5) 15

1CEA100-30 30 CEA100-120 120 0.9 3.0 (76.2) 24

1-1/4 CEA125-15 15 CEA125-60 60 0.9 3.5 (88.9) 31

1-1/2 CEA150-15 15 CEA150-45 45 1.0 4.5 (114.3) 40

2CEA200-15 15 CEA200-30 30 1.0 5.5 (139.7) 53

2-1/2 CEA250-8 8-- 1.3 8.0 (203.2) 76

3CEA300-8 8-- 1.3 10.0 (254.0) 118

4CEA400-8 8-- 1.5 12.0 (304.8) 156

5CEA500-8** 8-- 2.5 17.5 (444.5) 212

6CEA600-8** 8-- 2.5 22.5 (635.0) 259

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

**Available on request.

Type ACEA also available (liquidtight flexible aluminum conduit).

Aluminum core weighs approximately one third less than steel core.

Type CEA Combustion & Flammability Properties

Combustion & Flammability Properties** Test Value

-Vertical Burn (Material) UL94 V-O Rating

No Flaming Drips

-Vertical Burn (Conduit) UL360 Pass

No Flaming Drips

-Oxygen Index % D2863 28.5

-Flame Spread Index ASTM E162 4.0

No Flaming Drips

-Flame Propagation ASTM C542 Pass

(NFPA-130) No Flaming Drips

-Smoke Generation (Flaming) ASTM E662 Ds 41 @ 1.5 min

(NFPA 258) Ds 94 @ 4.0 min

-Smoke Generation (Non-Flaming) ASTM E662 Ds 7 @ 1.5 min

(NFPA 258) Ds 45 @ 4.0 min

-Toxic Gas Generation BOMBARDIER SMP 800-C Pass

-Toxicity Index NES 713 3.9

**Test data is based on controlled laboratory conditions and does not necessarily reflect

performance in actual fire conditions. Additional product information available upon request.

Typ e CEA

This liquidtight flexible steel conduit is

designed for applications where safety

concerns exist regarding a material’s

reaction in a fire situation.

Construction

The flexible inner core of this product is

made from a galvanized steel strip. As

in type LT, this core contains string

packing between the helical

convolutions in trade sizes 3/8” through

2”. The specially formulated

thermoplastic polyurethane jacket has

excellent flame retardant characteristics

as well as low smoke and toxicity

generation characteristics. Acidic gases

such as hydrogen chloride, hydrogen

fluoride and hydrogen bromide are

virtually eliminated as products of

combustion.

Applications

This product is ideally suited for

installation in confined or enclosed

areas where construction materials

must generate very little smoke, and

have a low flame spread as well as low

toxic gas emissions in the event of fire.

Such applications include mass transit

vehicles where CEA is extensively

used for wiring harnesses within and

under passenger rail cars. Other

applications include use in underground

subway structures and tunnels.

Working Temperatures

-40°C to 80°C

Standard Colours

Grey and black. Other colours available

upon request. Part numbers listed

designate grey jacket.

CONFITMRO_EN_ALL.pdf 137 11/28/2011 11:05:44 AM

138

T&B Conduit Fittings

Liquatite®Flexible Conduit— Aluminum

Type ACEA — Non-Halogen, Low Smoke, Flame Retardant

Type ACEA

This liquidtight flexible aluminum

conduit is designed for applications

where safety concerns exist regarding a

material’s reaction in a fire situation.

Min. Inside Bend Weight Carton Reel

Trade Jacket Thick. Radius Kilogram Length Length Length Length

Size Type (mm) (mm) 30 m (m) Cat. No. (m) Cat. No. (m) Cat. No. (m) Cat. No.

3/8 ACEA038 0.8 50.8 5 60 ACEA038-30 --300 ACEA038-300 --

1/2 ACEA050 0.8 63.5 7 30 ACEA050-30 30 -300 ACEA050-300 --

3/4 ACEA075 0.9 76.2 9 30 ACEA075-30 45 ACEA075-45 150 ACEA075-150 --

1ACEA100 0.9 101.6 13 30 ACEA100-30 - -120 ACEA100-120 --

1-1/4 ACEA125 0.9 114.3 18 15 ACEA125-15 --75 ACEA125-75 --

1-1/2 ACEA150 1.0 139.7 25 15 ACEA150-15 --45 ACEA150-45 --

2ACEA200 1.0 177.8 33 15 ACEA200-15 --30 ACEA200-30 --

2-1/2 ACEA250 1.3 241.3 47 8 ACEA250-8 ------

3ACEA300 1.3 330.2 60 8 ACEA300-8 ------

4ACEA400 1.5 355.6 87 8 ACEA400-8 ------

5ACEA500 2.5 508.0 114 8 ** ------

6ACEA600 2.5 571.5 143 8 ** --

----

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

**Available on request.

Construction

The flexible inner core of this product is

made from an aluminum strip. As in

type CEA, this core contains string

packing between the helical

convolutions in trade sizes 3/8” through

1-1/4”. The specially formulated

thermoplastic polyurethane jacket has

excellent flame retardant characteristics

as well as low smoke and toxicity

generation characteristics. Acidic gases

such as hydrogen chloride, hydrogen

fluoride and hydrogen bromide are

virtually eliminated as products of

combustion.

Applications

This product is ideally suited for

installation in confined or enclosed

areas where construction materials

must generate very little smoke, and

have a low flame spread as well as low

toxic gas emissions in the event of fire.

Such applications include mass transit

vehicles where ACEA is extensively

used for wiring harnesses within and

under passenger rail cars. Other

applications include use in underground

subway structures and tunnels.

Working Temperatures

-40°C to 80°C

Standard Colours

Machine Tool Grey. Other colours

available upon request.

Note

A UL listed version is pending. Consult

factory for availability of type ZHLA.

Type ACEA Combustion & Flammability Properties

Combustion & Flammability Properties** Test Value

-Vertical Burn (Material) UL94 V-O Rating

No Flaming Drips

-Vertical Burn (Conduit) UL360 Pass

No Flaming Drips

-Oxygen Index % D2863 28.5

-Flame Spread Index ASTM E162 9.8

-Flame Propagation ASTM C542 Pass

(NFPA-130) No Flaming Drips

-Smoke Generation (Flaming) ASTM E662 Dm 103 (Corrected)

(NFPA 258) Ds 47 @ 4.0 min

-Smoke Generation (Non-Flaming) ASTM E662 Dm 91 (Corrected)

(NFPA 258) Ds 5 @ 1.5 min

-Toxic Gas Generation SMP 801 Pass

-Toxicity Index NES 713 3.9

**Test data is based on controlled laboratory conditions and does not necessarily reflect

performance in actual fire conditions. Additional product information available upon request.

CONFITMRO_EN_ALL.pdf 138 11/28/2011 11:05:44 AM

139

T&B Conduit Fittings

Liquatite®Flexible Conduit— Steel

Type ZHLA — Non-Halogen, Low Smoke, Flame Retardant

Trade Carton Carton Carton Inside

Size Content* Content* Content* Bend Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 ZHLA038-30 30 ZHLA038-150 150 ZHLA038-300 300 2.0 (50.8) 13

1/2 ZHLA050-30 30 ZHLA050-150 150 ZHLA050-300 300 3.0 (76.2) 15

3/4 ZHLA075-30 30 ZHLA075-150 150 ZHLA075-300 300 4.2 (106.7) 24

1ZHLA100-30 30 ZHLA100-120 120 -- 5.5 (139.7) 37

1-1/4 ZHLA125-15 15 ZHLA125-60 60 -- 7.0 (177.8) 46

1-1/2 ZHLA150-15 15 ZHLA150-45 45 -- 4.5 (114.3) 47

2ZHLA200-15 15 ZHLA200-30 30 -- 6.0 (152.4) 66

2-1/2 ZHLA250-8 8---- 8.0 (203.2) 87

3ZHLA300-8 8 ---- 10.0 (254.0) 114

3-1/2 ZHLA350-8 8 ---- 11.0 (279.4) 140

4ZHLA400-8 8---- 12.0 (304.8) 154

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type ZHLA Combustion & Flammability Properties

Combustion & Flammability Properties** Test Value

-Vertical Burn (Material) UL94 V-O Rating

No Flaming Drips

-Vertical Burn(Conduit) UL360 Pass

No Flaming Drips

-Oxygen Index % D2863 28.5

-Flame Spread Index ASTM E162 4.0

No Flaming Drips

-Flame Propagation ASTM C542 Pass

(NFPA-130) No Flaming Drips

-Smoke Generation (Flaming) ASTM E662 Ds 41 @ 1.5 min

(NFPA 258) Ds 94 @ 4.0 min

-Smoke Generation (Non-Flaming) ASTM E662 Ds 7 @ 1.5 min

(NFPA 258) Ds 45 @ min

-Toxic Gas Generation BOMBARDIER SMP 800-C Pass

-Toxicity Index NES 713 3.9

** Test data is based on controlled laboratory conditions and does not necessarily reflect

performance in actual fire conditions. Additional product information available upon request.

Type ZHLA

Non-halogen, low smoke and low flame

spread are what makes Type ZHLA a

proven choice for applications where

limiting toxic combustion materials is an

important issue. Since ZHLA is also UL

Listed, it is ideal for field installation in

confined, public areas such as subways,

tunnels, etc.

Construction

ZHLA has a flexible inner core made from

a spiral wound strip of heavy gauge, hot-

dipped galvanized steel. The 3/8 through

1-1/4 inch trade sizes contain

an integral bonding strip of copper. The 1-

1/2

inch

and larger sizes are designed with

a fully interlocked strip.

The specially formulated thermoplastic

black polyurethane jacket has excellent

flame resistance and low smoke and

toxicity generation characteristics. It is

also resistant to ozone, hydrocarbons,

moderate chemicals, oils and fuels. Refer

to the Conduit — Chemical Resistance

Guide beginning on p. 156.

Applications

There are many situations and areas

where PVC is not allowed for electrical

construction. The jacketing material used

for ZHLA virtually eliminates the release of

acidic gases found in PVC products.

- Meets the requirements of

Bombardier SMP 800-C for Toxic

Gas Generation

- Meets the requirements of both

ASTM E162 for Flame Spread and

ASTM E662 for Smoke Generation.

- Listed and marked for direct burial

and in poured concrete.

- For containment of 600-volt and

lower potential circuits.

- Sunlight resistant

Working Temperatures

-40°C to 80°C Air / 60°C Wet / 70°C Oil

Listing / Certification

Listed. Conforms to UL Standard

ANSI/ UL-360 for Liquidtight Flexible

Steel Conduit.

Standard Colour

Black

CONFITMRO_EN_ALL.pdf 139 11/28/2011 11:05:45 AM

140

T&B Conduit Fittings

Liquatite®Flexible Conduit— Shielding

Type LAS

Trade Carton Carton Inside

Size Content* Content* Bend Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 LAS038-30 30 LAS038-150 150 2.0 (50.8) 13

1/2 LAS050-30 30 LAS050-150 150 3.0 (76.2) 15

3/4 LAS075-30 30 LAS075-150 150 4.2 (106.7) 24

1LAS100-30 30 LAS100-120 120 5.5 (139.7) 37

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type LAS

Type LAS is identical to standard UL Listed

liquidtight flexible steel conduit but is

augmented with a tinned copper shielding

braid located over the inner steel core and

under its protective PVC jacket. The braid

offers a minimum of 90% coverage

resulting in a shielding effectiveness range

from 126 dB @ 1 MHz to 66 dB @ 1 GHz.

Applications

PVC jacket is resistant to a wide variety of

oils, acids, alkalines and ultraviolet light.

Working Temperatures

-20°C to 60°C

Listing / Certifications

Listed. Conforms to UL360 for

liquidtight flexible steel conduit.

Standard Colours

Black. Other colours and jacketing

materials available. Consult your Regional

Sales Office for details.

Thomas & Betts offers three types of

flexible liquidtight conduits designed for

wiring applications requiring shielding

effectiveness from Electro-Magnetic

and Radio Frequency Interference

(EMI/RFI).

This series of shielding conduits consists

of three configurations: Type LAS, Type

EMS and Type EMSP.

These conduits are used to protect

sensitive electronic circuits such as

communications, radar, and data

transmission from outside interference or

“noise”. The reverse situation is also

an issue. Today’s Original Equipment

Manufacturers (OEMs) are finding that, if

they wish to ship electrical equipment into

the European community, they may need

to be in compliance with recently

developed CE standards which reduce

the allowable amount of EMI/RFI

emissions from electrical apparatus.

All three are designed to accept

industry standard liquidtight fittings and

address the problems of assembly and

grounding. Fittings of this type include a

grounding ferrule which contacts the

internal metallic material of

the conduit and the fitting body. This

produces a direct shield-to-drain or

ground, simply by tightening the fitting.

The graph below depicts the shielding

effectiveness (attenuation in dBs) of all

three types. The dotted line shows

a comparison to standard unshielded

liquidtight flexible conduit, Type LA. The

spectrum of test frequency is from 1 MHz

to 10 MHz Electric Field, to 100 MHz to

1 GHz (1000 MHz) Planewave Field.

Tests were performed per MIL-STD-285

on 1/2inch trade size conduit.

Shielding Effectiveness

1 MHz 10 MHz 100 MHz 450 MHz 1 GHz

EMSP 127 130 136 116 118

EMS 126 122 131 98 97

LAS 126 98 75 76 66

LA 110 80 53 63 51

ATTENUATION (dB)

CONFITMRO_EN_ALL.pdf 140 11/28/2011 11:05:45 AM

141

T&B Conduit Fittings

Liquatite®Flexible Conduit— Shielding

Type EMS

Type EMS has an inner core that is

made from a fully interlocked bronze

strip. Even though it does not contain a

braided shield, it offers a shielding

effectiveness from 126 dB @ 1 MHz to

nearly 100 dB @ 1 GHz.

Working Temperatures

-55°C to 105°C

Standard Colour

Grey. Other colours and jacketing

materials available.

Consult your Regional

Sales Office for details.

Trade Carton Carton Inside

Size Content* Content* Bend Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 EMS038-30 30 EMS038-150 150 3.0 (76.2) 12

1/2 EMS050-30 30 EMS050-150 150 3.0 (76.2) 16

3/4 EMS075-30 30 EMS075-150 150 4.0 (101.6) 20

1EMS100-30 30 EMS100-120 120 4.0 (101.6) 39

1-1/4 EMS125-15 15 EMS125-60 60 4.5 (114.3) 46

1-1/2 EMS150-15 15 EMS150-45 45 7.0 (177.8) 64

2EMS200-15 15 EMS200-30 30 9.5 (241.3) 82

2-1/2 EMS250-8 8-- 12.0 (304.8) 105

3EMS300-8 8 -- 13.5 (342.9) 145

4EMS400-8 8 -- 17.0 (431.8) 176

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Type EMSP

Type EMSP is a hybrid of LAS and EMS. It

utilizes the same bronze core and PVC

jacket as EMS but gets further screening

protection from a tinned copper braid as

found in the LAS product. Its range of

shielding effectiveness is from 126 dB @

1 MHz to 120 dB @ 1 GHz.

Trade Carton Carton Inside

Size Content* Content* Bend Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 EMSP038-30 30 EMSP038-150 150 3.0 (76.2) 12

1/2 EMSP050-30 30 EMSP050-150 150 3.0 (76.2) 16

3/4 EMSP075-30 30 EMSP075-150 150 4.0 (101.6) 20

1EMSP100-30 30 EMSP100-120 120 4.0 (101.6) 39

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

INTERLOCK

Type EMSP

CONFITMRO_EN_ALL.pdf 141 11/28/2011 11:05:45 AM

Type BR

Min.Trade Coil Coil Coil Coil Coil Inside

Size Content Content Content Content Content Bend Radius

Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) kg/30m

3/8 BR038-8* 8BR038-15* 15 BR038-30* 30 BR038-75* 75 BR038-300* 300 2.0 (50.8) 18

1/2 BR050-8 8BR050-15 15 BR050-30 30 --BR050-300 300 3.0 (76.2) 13

3/4 BR075-8 8BR075-15 15 BR075-30 30 --BR075-150 150 4.0 (101.6) 15

1--BR100-15 15 ----BR100-120 120 5.0 (127.0) 24

1-1/4 --BR125-15 15 ----BR125-120 120 6.2 (157.5) 29

1-1/2 --BR150-8 8----BR150-90 90 7.5 (190.5) 36

2--BR200-8 8----BR200-45 45 10.0 (254.0) 45

2-1/2 --BR250-8 8------ 12.5 (317.5) 68

3--BR300-8 8------ 15.0 (381.0) 82

3-1/2 --BR350-8 8------ 17.5 (444.5) 100

4--BR400-8 8------ 20.0 (508.0) 122

* CSA Certified.

Type BR

This non-jacketed flexible steel conduit has

many universal wiring applications. It is often

referred to as “Greenfield” or “Reduced

Wall Flex”.

Construction

Type BR is formed from high corrosion

resistant hot-dipped galvanized steel. Its

profile and helical shape allow it to

withstand impact and crushing forces.

Applications

General Use:

In accordance with CEC Rule 12-1002 (1)

the flexible metal conduit is permitted in or

on buildings of either combustible or non-

combustible constructions.

Restriction and Exception:

CEC Rule 12-1004 (a) states:“12 (

3/8

)

trade size flexible metal conduit shall be

permitted to be used for runs of not more

than 1.5 m (5 ft) for the connection

of equipment.”

and CEC Rule 12-1004 (b) states:“12 (

3/8

)

trade size liquidtight flexible conduit may be

used as permitted by this code.”

Securements with straps:

CEC Rule 12-1010 (3) states: “When

flexible metal conduit is installed, it shall be

secured at intervals not exceeding 1.5 m (5

ft) and within 300 mm (12 in.) on each side of

every outlet box or fitting except where

flexible metal conduit is fished and except for

lengths of not over 900 mm (3 ft) at terminals

where flexibility is necessary.”

Conductor fill:

CEC Rule 12-1014 defines the maximum

number of conductor, the CEC Tables 6

provides the maximum number of

conductors of one size in trade sizes of

conduit,CEC Table 8 provides the maximum

allowable per cent conduit fill, and CEC Table

9 provides the cross-sectional areas of

conduit.

Specific Use and applications:

Elevators, Hoistways, in accordance with

CEC Rules 38-021 (1) (a) (1) and 38-0221 (1)

(a) (iv)

Elevators, Cars, in accordance with CEC

Rules 38-021 (1) (b) (v)

Elevators, Within Machine Rooms, Control

Rooms and Machinery Spaces and Control

Spaces, in accordance with CEC Rule

38-021 (1) (c) (1)

Elevators, Conterweights, in accordance

with CEC Rule 38-021 (1) (d)

EScalators, in accordance with CEC Rule

38-021 (2)

Lifts for persons with physical disabilities, in

accordance with CEC Rule 38-021 (3)

Theater installation, in accordance with CEC

Rule 44-102 (1)

Listing/ Certification

Listed. (sizes 3/8 through 3 in.).

Conforms to UL Standard ANSI/UL-1

for Flexible Metal Conduit.

Certified. (3/8 inch size only).

Conforms to CSA 22.2 No. 56 for use

per CEC C22.1 Section 12-1000.

Meets Federal Specification WW-C-566c

Type II

Flexible metal conduit is also per mitted

for use on industrial machinery where

temperatures exceed the limits of

liquidtight flexible conduit. (ANSI/NFPA-79)

Section 16.3.4 (exception) and Section

17.9.

Trade Inner Diameter Outer Diameter

Size Min. Max. Min. Max.

(in.) Cat. No. in. (mm) in. (mm) in. (mm) in. (mm)

3/8 BR038* 0.375 (9.5) 0.393 (10.0) 0.560 (14.2) 0.610 (15.5)

1/2 BR050 0.625 (15.9) 0.645 (16.4) 0.860 (21.8) 0.920 (23.4)

3/4 BR075 0.812 (20.6) 0.835 (21.2) 1.045 (26.5) 1.105 (28.1)

1BR100 1.000 (25.4) 1.040 (26.4) 1.300 (33.0) 1.380 (35.1)

1-1/4 BR125 1.250 (31.8) 1.300 (33.0) 1.550 (39.4) 1.630 (41.4)

1-1/2 BR150 1.500 (38.1) 1.575 (40.0) 1.850 (47.0) 1.950 (49.5)

2BR200 2.000 (50.8) 2.080 (52.8) 2.350 (59.7) 2.454 (62.3)

2-1/2 BR250 2.500 (63.5) 2.700 (68.6) 2.860 (72.6) 3.060 (77.7)

3BR300 3.000 (76.2) 3.200 (81.3) 3.360 (85.3) 3.560 (90.4)

3-1/2 BR350 3.500 (88.9) - - 3.860 (98.0) 4.060 (103.1)

4BR400 4.000 (101.6) - - 4.360 (110.7) 4.560 (115.8)

* CSA Certified.

Types BR and ABR Strip Profile

142

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

CONFITMRO_EN_ALL.pdf 142 11/28/2011 11:05:45 AM

143

T&B Conduit Fittings

Liquatite®Flexible Conduit — Aluminum

Type ABR

Trade Coil Coil Coil Reel

Size Length Length Length Content* Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) Cat. No. (m) kg/30m

-- - - -ABR716-30 30 ABR716-300 300 -

3/8 ABR038-8†8ABR038-15†15 ABR038-30†30 ABR038-300†300 7.0

1/2 ABR050-8 8ABR050-15 15 ABR050-30 30 ABR050-300 300 9.5

3/4 ABR075-8 8ABR075-15 15 ABR075-30 30 ABR075-150 150 13.5

1- -ABR100-15 15 - - ABR100-120 120 24.0

1-1/4 - - ABR125-15 15 - - ABR125-120 120 31.0

1-1/2 - - ABR150-8 8 - - ABR150-90 90 47.0

2- -ABR200-8 8 - - ABR200-45 45 67.0

2-1/2 - - ABR250-8 8-- -92.0

3- -ABR300-8 8 - - - 107.0

3-1/2 - - ABR350-8 8 - - - 122.0

4- -ABR400-8 8 - - - 142.0

See Chart on p.155 for dimensions and tolerances.

* See p.155 for label and packaging detail.

Note: Dimensions and Bend Radii are identical to Type BR, p. 140.

† CSA Certified.

trade size liquidtight flexible conduit may be

used as permitted by this code.”

Securements with straps:

CEC Rule 12-1010 (3) states: “When

flexible metal conduit is installed, it shall be

secured at intervals not exceeding 1.5 m (5

ft) and within 300 mm (12 in.) on each side of

every outlet box or fitting except where

flexible metal conduit is fished and except for

lengths of not over 900 mm (3 ft) at terminals

where flexibility is necessary.”

Conductor fill:

CEC Rule 12-1014 defines the maximum

number of conductor, the CEC Tables 6

provides the maximum number of

conductors of one size in trade sizes of

conduit, CEC Table 8 provides the

maximum allowable per cent conduit fill,

and CEC Table 9 provides the cross-

sectional areas of conduit.

Applications: refer to Type BR, p. 142.

Listing/ Certification

Listed. (sizes 3/8 through 3 in.).

Conforms to UL Standard ANSI/UL-1

for Flexible Metal Conduit.

Certified. (3/8 inch size only).

Conforms to CSA 22.2 No. 56 for

use per CEC C22.1 Section 12-1300.

Meets Federal Specification WW-C-566c

Type II

Type ABR

This non-jacketed flexible aluminum

conduit has many universal wiring

applications. It is often referred to as

“Greenfield” or “Reduced Wall Flex”.

Construction

Type ABR is formed using a high strength

aluminum alloy strip. The result is a conduit

with similar characteristics to those of type

BR steel but at about 1/3the weight.

Applications

General Use:

In accordance with CEC Rule 12-1002 (1)

the flexible metal conduit is permitted in or

on buildings of either combustible or non-

combustible constructions.

Restriction and Exception:

CEC Rule 12-1004 (a) states:“12 (

3/8

) trade

size flexible metal conduit shall be permitted

to be used for runs of not more than 1.5 m

(5 ft) for the connection of equipment.”

and CEC Rule 12-1004 (b) states:“12 (3/8)

CSA Internal Outer Inside WT. Coil

Trade Metric T&B Diameter (in.) Diameter (in.) Bend Lbs. per Lenght

Size Desig. Type Min. Max. Min. Max. Radius 100 Ft. Mtr.

3/8 12 ABRH038 0.375 0.393 0.560 0.610 2 7 30, 150, 300

7/16 14 ABRH716 0.437 0.457 - 0.675 2.25 8 30, 150, 300

1/2 16 ABRH050 0.625 0.645 0.860 0.920 3 16 30, 150, 300

3/4 21 ABRH075 0.812 0.835 1.045 1.105 4 18 30, 150, 300

127ABRH100 1.000 1.040 1.300 1.380 5 35 15, 120

1-1/4 35 ABRH125 1.250 1.300 1.550 1.630 6.2 43 15, 120

1-1/2 41 ABRH150 1.500 1.575 1.850 1.950 7.5 55 8, 15, 30

253ABRH200 2.000 2.080 2.350 2.454 10 73 8, 15

2-1/2 63 ABRH250 2.500 2.700 2.860 3.060 12.5 90 8, 15

378ABRH300 3.000 3.200 3.360 3.560 15 107 8, 15

4 103 ABRH400 4.000 - 4.360 4.560 20 142 8, 15

Type ABRH

TYPE - ABRH

This non-jacketed flexible aluminum

conduit has many universal wiring

applications.

Construction

Type ABRH is formed from a heavy

gauge aluminum strip. Its profile and

helical shape allow it to withstand

substantial impact and crushing forces.

Applications

This conduit is intended as a metal

raceway for wires and cable where CSA

Certification is required. Suitable for use

with connectors intended for “FMC

(Flexible Metal Conduit).

Certified

File # LL 18858 Conforms to CSA

22.2 No. 56 for use per the Canadian

Electrical Code C22.1 Section 12-1300.

CONFITMRO_EN_ALL.pdf 143 11/28/2011 11:05:46 AM

144

T&B Conduit Fittings

Liquatite®Flexible Conduit — Steel

Type SL

Coil

Inside Diameter Outside Diameter Min. Inside

Trade Size Content

in.

ax.

in.

ax.

Bend Radius Wt.

(in.) (mm) Cat. No. (m) in. (mm) in. (mm) in. (mm) in. (mm) (in) (mm) kg/30m

--SL316-75 75 0.172 (4.35) 0.202 (5.13) 0.280 (7.11) 0.310 (7.87) 0.75 (19.5) 2

--SL140-75 75 0.235 (5.97) 0.265 (6.73) 0.328 (8.33) 0.358 (9.09) 0.75 (19.5) 3

5/16 - SL516-75 75 0.297 (7.54) 0.327 (8.31) 0.391 (9.93) 0.421 (10.69) 0.75 (19.5) 3

--SL380-75 75 0.360 (9.14) 0.390 (9.91) 0.485 (12.32) 0.515 (13.08) 1.00 (25.4) 4

--SL716-75 75 0.422 (10.72) 0.452 (11.48) 0.547 (13.89) 0.577 (14.66) 1.00 (25.4) 4

3/8 16 SL038-75 75 0.492 (12.50) 0.512 (13.00) 0.617 (15.67) 0.637 (16.18) 1.00 (25.4) 5

--SL916-45 45 0.547 (13.89) 0.577 (14.66) 0.672 (17.07) 0.702 (17.83) 1.25 (31.8) 5

1/2 - SL050-45 45 0.622 (15.80) 0.642 (16.31) 0.747 (18.97) 0.767 (19.48) 1.50 (38.1) 7

-20SL050M-45 45 0.650 (16.51) 0.670 (17.01) 0.775 (19.69) 0.795 (20.19) 1.50 (38.1) 7

--SL340-45 45 0.735 (18.67) 0.765 (19.43) 0.865 (21.97) 0.895 (22.73) 1.50 (38.1) 8

3/4 25 SL075-30 30 0.827 (21.00) 0.847 (21.51) 0.957 (24.31) 0.977 (24.82) 2.00 (50.8) 8

1-SL100-15 15 1.041 (26.44) 1.066 (27.07) 1.181 (30.00) 1.206 (30.63) 2.00 (50.8) 9

-32SL100M-15 15 1.102 (27.99) 1.122 (28.50) 1.242 (31.55) 1.262 (32.05) 2.00 (50.8) -

Type SL

This “extra-flexible” product, available in the

smaller diameters, is designed for tightspot

installation and where continuous flexing is

required of a steel wound hose.

Construction

Type SL is helically wound from a formed

strip of Electro-Galvanized steel. It is sized to

be used with a variety of set-screw and

clamp type fittings.

Applications

Offers good mechanical protection to wiring

in a variety of O.E.M. applications.

Squarelock

Type USL

This extra-flexible steel conduit is recognized

UL and CSA for use within listed and certified

assemblies.

Construction

Helically formed from hot-dipped galvanized

steel, type USL offers good corrosion

resistance and provides excellent

mechanical protection to enclosed circuits.

Applications

This product is intended as a factory

installed component of various

assemblies. Typical uses include modular

office partitions, showcase lighting, range

tops and other appliances.

Listing / Certification

UL Recognized.

Inner Dia. Outer Dia. Coil Min. Inside

Min. Max. Min. Max. Contents Bend Radius Wt.

Cat. No. in. (mm) in. (mm) in. (mm) in. (mm) Cat. No. (m) in. (mm) kg/30m

USL516 0.297(7.54) 0.327(8.30) 0.457(11.60) 0.487(12.37) USL516-75 75 1.25 (31.75) 5

USL380 0.360(9.14) 0.390(9.91) 0.520(13.20) 0.550(13.97) USL380-75 75 1.25 (31.75) 6

USL716 0.422(10.7) 0.452(11.48) 0.582(14.78) 0.612(15.54) USL716-75 75 1.50 (38.10) 7

USL120 0.485(12.3) 0.515(13.08) 0.645(15.86) 0.675(17.15) USL120-75 75 1.50 (38.10) 8

USL916 0.557(14.1) 0.577(14.65) 0.707(17.96) 0.737(18.72) USL916-75 75 1.50 (38.10) 9

Type USL

Squarelock —Type USL

CONFITMRO_EN_ALL.pdf 144 11/28/2011 11:05:46 AM

145

T&B Conduit Fittings

Liquatite®Flexible Conduit— Steel

Type VJC — with PVC Jacket

Type VJC

Vacuum jacketed steel conduit for high-flex

installations.

Construction

A unique vacuum extrusion process allows

this product to have a thin PVC jacket which

does not restrict the great flexibility

characteristics of the inner core. The core

material is the same as type SL. VJC is

designed with dimensions that will accept

standard liquidtight fittings.

Applications

VJC is suitable for use in both static

applications where a tight bend diameter is

needed and in dynamic use such as

machining centers and robotics.

Working Temperatures

-20°C to 80°C

Standard Colour

Black. Other colours available upon

request. Consult your Regional Sales

Office for details.

Outside Dia. Internal

Trade Carton Over Jacket Bend radius

Size Content* Min. Max. Static Dynamic Wt.

(in.) Cat. No. (m) in. (mm) in. (mm) in. (mm) in. (mm) kg/30m

3/8 VJC038-30 30 0.647 (16.43) 0.677 (17.20) 1.0 (25.4) 5 (127.0) 5

1/2 VJC050-30 30 0.777 (19.74) 0.807 (20.50) 1.5 (38.1) 6 (152.4) 7

-VJC050M-30 30 0.805 (20.45) 0.835 (21.21) 1.5 (38.1) 6 (152.4) 7

3/4 VJC075-30 30 0.987 (25.07) 1.017 (25.83) 2.0 (51.0) 10 (254.0) 9

1VJC100-30 30 0.221 (5.61) 1.246 (31.65) 3.0 (76.0) 10 (254.0) 11

-VJC100M-30 30 1.272 (32.31) 1.302 (33.07) 3.0 (76.0) 10 (254.0) -

* Reels available. Consult factory.

Type UG

A fully-interlocked flexible steel conduit

designed for high strength in “tight-spot”

installations.

Construction

This conduit is manufactured from a bright

tin plated steel strip which is fully

interlocked at the edges to produce a

strong, yet flexible product. The interlock

feature does not allow the conduit to

unravel if twisted and permits the conduit

to retain it’s shape when bent. This

lightweight product is compatible with

many set-screw and clamp type fittings.

Applications

The bright appearance of the finished

product lends itself to installations

where the conduit may be visible after

final assembly.

Coil Inside diameter Outside DiameterMin. Inside

Content Min. Max. Min. Max. Bend Radius Wt.

Cat. No. (m) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) kg/30m

UG380-15 15 0.443(11.25) 0.473(12.01) 0.563(14.30) 0.593(15.06) 2.5 (63.5) 7

UG120-15 15 0.755(19.18) 0.785(19.94) 0.875(22.23) 0.905(22.99) 3.0 (76.2) 10

UG340-15 15 0.943(23.95) 0.973(24.71) 1.063(28.70) 1.093(27.76) 3.5 (89.0) 14

UG100-15 15 1.208(30.68) 1.238(31.45) 1.328(33.73) 1.358(34.50) 4.5 (114.3) 16

UG125-15 15 1.485(37.72) 1.515(38.48) 1.578(40.08) 1.608(40.84) 5.5 (139.7) 23

UG150-15 15 1.735(44.07) 1.765(44.83) 1.843(46.81) 1.873(47.57) 6.5 (165.1) 27

UG200-15 15 2.235(56.77) 2.265(57.53) 2.390(60.71) 2.420(61.47) 8.5 (216.0) 36

UG250-15 15 2.735(69.47) 2.765(70.23) 2.937(74.60) 2.967(75.36) 10.5 (267.0) 39

UG300-15 15 3.36085.34) 3.390(86.11) 3.438(87.33) 3.468(88.09) 13.0 (330.2) 48

Note: Trade sizes do not apply to Type UG.

Type UG

Interlock

CONFITMRO_EN_ALL.pdf 145 11/28/2011 11:05:46 AM

Type LNM-P

Trade Carton Reel Reel Inside Dia.

Outside Dia.

Inside

Size

Content Content Content Min. Max. Min. Max. Bend Radius Wt.

(in.) Cat. No. (m) Cat. No. (m) Cat. No. (m) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) kg/30m

3/8 LNMP038-75 75 LNMP038-150 150 LNMP038-300 300 0.485(12.32) 0.505(12.83) 0.755(19.18) 0.775(19.69) 2.5 (63.5) 7

1/2 LNMP050-60 60 LNMP050-150 150 LNMP050-300 300 0.620(5.08) 0.640(16.26) 0.910(23.11) 0.930(23.62) 3.0 (76.2) 10

3/4 LNMP075-50 50 LNMP075-150 150 -- 0.815(20.70) 0.835(21.21) 1.150(29.21) 1.170(29.72) 4.0 (101.6) 14

1LNMP100-30 30 LNMP100-120 120 -- 1.030(26.16) 1.055(26.80) 1.415(35.94) 1.440(36.58) 6.0 (152.4) 19

1-1/4 LNMP125-30 30 LNMP125-60 60 -- 1.370(34.80) 1.395(35.43) 1.800(45.72) 1.825(46.36) 7.0 (177.8) 28

1-1/2 LNMP150-15 15 LNMP150-45 45 -- 1.585(40.26) 1.620(41.15) 2.045(51.94) 2.080(52.83) 8.0 (203.2) 36

2LNMP200-15 15 LNMP200-30 30 -- 2.075(52.71) 2.100(53.34) 2.555(64.90) 2.590(65.79) 9.0 (228.6) 54

Type LNM-P

This nonmetallic liquidtight conduit is

ideally suited for continuous flexing

situations. It is often specified in “Power

Track” or cable carrier installations and on

industrial robots. It does not contain a

metal core which could fatigue from

repeated flexing or vibration.

Construction

LNM-P is of the Layered, Type-A

construction which incorporates a

smooth seamless inner core of flexible

PVC that is bonded to a covering of

flexible PVC. Between these layers is a

woven nylon mesh for added

reinforcement. The PVC material is a

high quality flame-retardant compound

which resists oils, mild acids and

exposure to sunlight.

Applications

General Use:

In accordance with CEC Rule 12-1002 (1)

the flexible metal conduit is permitted in or

on buildings of either combustible or non-

combustible constructions.

Restriction and Exception:

CEC Rule 12-1004 (a):“12 (3/8) trade

size flexible metal conduit shall be permitted

to be used for runs of not more than

1.5 m (5 ft) for the connection of equipment.”

and CEC Rule 12-1004 (b):“12 (3/8) trade

size liquidtight flexible conduit may be used

as permitted by this code.”

Securements with straps:

CEC Rule 12-1010 (3): “When flexible

metal conduit is installed, it shall be secured

at intervals not exceeding 1.5 m (5 ft) and

within 300 mm (12 in.) on each side of every

outlet box or fitting except where flexible

metal conduit is fished and except for

lengths of not over 900 mm (3 ft) at terminals

where flexibility is necessary.”

Conductor fill:

CEC Rule 12-1014 defines the maximum

number of conductor, the CEC Tables 6

provides the maximum number of

conductors of one size in trade sizes of

conduit,

CEC Table 8 provides the maximum

allowable per cent conduit fill, and CEC Table

9 provides the cross-sectional areas of

conduit.

Specific Use and applications:

Elevators, Hoistways, in accordance with

CEC Rules 38-021 (1) (a) (1) and 38-0221 (1)

(a) (iv)

Elevators, Cars, in accordance with CEC

Rules 38-021 (1) (b) (v)

Elevators, Within Machine Rooms, Control

Rooms and Machinery Spaces and Control

Spaces, in accordance with CEC Rule

38-021 (1) (c) (1)

Elevators, Conterweights, in accordance

with CEC Rule 38-021 (1) (d)

EScalators, in accordance with CEC Rule

38-021 (2)

Lifts for persons with physical disabilities, in

accordance with CEC Rule 38-021 (3)

Theater installation, in accordance with CEC

Rule 44-102 (1)

Working temperatures

-20°C to 60°C

Listing / Certification

Listed. Conforms to UL Standard

ANSI/UL 1660 type A

Certified. Conforms to CSA 22.2

No. 227.2 type A

Standard Colour

Safety Orange. Also available in

Black and Grey. Part numbers listed

designate Orange jacket.

Fittings

Fittings for Layered Conduit are for that

conduit only and are so identified by the

marking “FNMC-A”.

Recommendation:

“Suitable for use with 3700 Series, Type

A, Metal Fittings from Thomas & Betts”.

Refer to pgs. 101, 102.

LNM-P TYPE A

146

T&B Conduit Fittings

Liquatite®Flexible Conduit— Nonmetallic

CONFITMRO_EN_ALL.pdf 146 11/28/2011 11:05:46 AM

147

T&B Conduit Fittings

Liquatite®Flexible Conduit— Nonmetallic

Type NMC

Trade Inside Bend Weight Coil footage I.D. (in.) O.D. (in.)

Type Size Radius (lb/100ft) Length Min. Max. Min. Max.

NMC038TB 3/8” 2.00” 10 100 .484 .504 .690 .710

NMC050TB 1/2” 3.25” 11 100 .622 .642 .820 .840

NMC075TB 3/4” 4.25” 15 100 .820 .840 1.030 1.050

NMC100TB 1” 6.50” 25 100 1.041 1.066 1.290 1.315

NMC125TB 1-1/4“ 8.00” 34 100 1.380 1.410 1.630 1.660

NMC150TB 1-1/2” 9.00” 42 50 1.575 1.600 1.865 1.900

NMC200TB 2” 11.00” 60 50 2.020 2.045 2.340 2.375

NMC050-1000TB 1/2” 3.25” 11 1000 .622 .642 .820 .840

NMC075-500TB 3/4” 4.25” 15 500 .820 .840 1.030 1.050

See technical data next page.

Use with Bullet®Liquidtight Fittings.

*Available in other colours. Consult Customer Service for details.

Type NMT

Trade Inside Bend Weight Coil footage I.D. (in.) O.D. (in.)

Type Size Radius (lb/100ft) Length Min. Max. Min. Max.

NMT038TB 3/8” .7” 6 100 .484 .504 .690 .710

NMT050TB 1/2” .9” 8 100 .622 .642 .820 .840

NMT075TB 3/4” 1.1” 10 100 .820 .840 1.030 1.050

NMT100TB 1” 1.3” 15 100 1.041 1.066 1.290 1.315

NMT125TB 1-1/4 “ 1.7” 20 100 1.380 1.410 1.630 1.660

NMT150TB 1-1/2” 1.9” 26 50 1.575 1.600 1.865 1.900

NMT200TB 2” 2.4” 36 50 2.020 2.045 2.340 2.375

*Available in other colours. Consult Customer Service for details.

Recommended industrial applications:

• Machine tools.

• Motor hookups.

• Food processing equipment.

• Extensions from wireways.

• Sensor and microswitch wiring found in

control consoles.

Recommended industrial applications:

• Protection of fiber optic cable.

• Installation of instrumentation and control

cable.

• Indoor/outdoor lighting.

• Packaging equipment.

• Marine and shipboard wiring.

• Flexing—component wiring protection on

robots, graphic arts equipment, etc.

Type NMC

A general purpose nonmetallic liquidtight

conduit offers excellent protection to

wiring from abrasion, sunlight, mild acids,

alkaline and oils. Often used for air

conditioning hook-ups and other outdoor

applications.

Construction Type B

NMC is of the helically wound integral Type

B construction. It contains a spiral of rigid

PVC reinforcement imbedded within the

flexible PVC wall.

Type NM Specifications

Type NMC is intended for installation in

accordance with CEC Rule 12-1300 to

12-1306 for Liquidtight Flexible Conduit.

-For containment of 600 volt and lower

potential circuits.

Working Temperature

-20°C to 80°C/Dry 60°C/Wet

70°C/Oil

Listed. Conforms to Underwriters

Laboratories Standard ANSI/UL 1660

type B

Certified. Conforms to CSA 22.2

No. 227.2 type B.

The 3/8 through 1-1/4 in. trade

sizes are listed and marked for direct

burial and in poured concrete.

Standard Colour

Black

Type NMT

Type NMT is an Extra Flexible Liquidtight

Nonmetallic Tubing. This lightweight tubing

cuts easily and installs quickly. It is ideal for

wiring protection in tight quarters and for

tight bends. The thin flexible PVC skin

allows greater movement for many OEM

applications. Used for wiring harnesses,

laboratory, equipment, fiber optics, etc.

Construction

Co-extruded from both flexible and rigid

PVC. The rigid spiral PVC reinforcement is

imbedded within the wall of the tubing.

Working Temperature

-20°C to 70°C

UL Recognized.

Standard Colour

Black.

CONFITMRO_EN_ALL.pdf 147 11/28/2011 11:05:47 AM

Features / Benefits Applications

148

T&B Conduit Fittings

Liquatite®Flexible Conduit— Nylon

• UL recognized

• Halogen free

• Flame resistant

• High impact and crush strength

• Resistant to many

chemicals

• Sunlight resistant

• Extreme temperature range

Type CL

Provides the best mechanical strength

and protection of the Corrlok conduits.

Material

Halogen Free Nylon 6

Working Temperatures

-40°C to 105°C

Fitting Pullout

150 lb (1/2” and larger). To be used with

Kopex®fittings of the Corrlok®System.

Listing / Certification

UL Recognized Component, 600 V,

105°C, Vertical Flame, Liquidtight,

UV and Impact Tested.

Standard Colour

Black. Other colours available upon

request.

Nominal Dimensions Min. Inside Standard

Inside Outside Bend Radius Static Wt. Length

Cat. No. (in.) MM MW in. (mm) in. (mm) in. (mm) kg/30m (m)

CL140-30 1/4 10 7 0.226 (6.5) 0.394 (10.0) 0.8 (20.3) 2.0 30

CL516-30 5/16 12 10 0.374 (9.5) 0.512 (13.0) 1.0 (25.4) 2.5 30

CL10-30 3/8 16 12 0.452 (11.5) 0.622 (15.8) 1.5 (38.1) 5.0 30

CL11-30 1/2 20 17 0.633 (16.1) 0.826 (21.0) 1.7 (43.2) 7.0 30

CL12-30 3/4 25 23 0.846 (22.5) 1.122 (28.5) 2.0 (50.8) 9.5 30

CL13-15 1 32 29 1.063 (27.0) 1.358 (34.5) 2.5 (63.5) 13.0 15

CL14-15 1-1/4 40 36 1.380 (35.0) 1.673 (42.5) 2.8 (71.1) 16.0 15

CL15-15 1-1/2 50 48 1.810 (46.0) 2.145 (54.5) 3.3 (83.8) 19.0 15

Type CL — Standard Weight

The Corrlok®System

Type - CLL

This light weight version provides many

of the same qualities of Type CL but

with Type CLL improved flexibility.

Material

Halogen Free Nylon 6

Working temperatures

-40°C to 105°C intermitting to 150°C

Fitting Pullout

40 lb (1/2” and larger). To be used with

Kopex®fittings of the Corrlok®System.

Listing / Certification

UL Recognized Component, 600 V,

105°C, Vertical Flame, Liquidtight,

UV and Impact Tested.

Standard Colour

Black. Other colours available upon

request.

Nominal Dimensions Min. Inside Standard

Inside Outside Bend Radius Static Wt. Length

Cat. No. (in.) MM MW in. (mm) in. (mm) in. (mm) kg/30m (m)

CLL10-30 3/8 16 12 0.452 (11.5) 0.622 (15.8) 0.7 (17.8) 3.4 30

CLL11-30 1/2 20 17 0.633 (16.1) 0.826 (21.0) 0.8 (20.3) 4.4 30

CLL12-30 3/4 25 23 0.865 (22.0) 1.122 (28.5) 1.2 (30.4) 6.7 30

CLL13-15 1 32 29 1.087 (27.6) 1.358 (34.5) 1.4 (35.6) 9.1 15

CLL14-15 1-1/4 40 36 1.420 (36.0) 1.673 (42.5) 2.4 (61.0) 11.0 15

CLL15-15 1-1/2 50 48 1.850 (47.0) 2.145 (54.5) 2.8 (71.1) 16.0 15

CLL17-10 2-1/2 70 70 2.645 (67.0) 3.150 (80.0) 6.3 (160.0) 32.0 10

CLL350-10 3-1/2 95 95 3.600 (91.5) 4.170 (106.0) 8.3 (210.8) 52.0 10

Type CLL — Light Weight

Conduit size

• Passenger rail vehicle wiring

• Industrial control equipment

• Machine tools

• Textile machinery

• Molding/extrusion equipment

• Fiber optics

• Medical equipment

The Corrlok®System is comprised of five

types of nylon, flexible corrugated

conduits designed for a wide range of

applications and are intended for use

with the new Kopex®series of fittings

and adapters. They are produced by an

extrusion/corrugation process resulting in

a flexible, seamless corrugated tube. The

internal corrugations are well rounded to

facilitate easier wire pulling.

The Corrlok®System provides a very

light weight, liquidtight flexible raceway

alternative that’s easy to work with

and stands up to tough environments.

Because the specially formulated nylons

used are nontoxic and self-extinguishing,

Corrlok®is a proven choice in confined

areas where hazards from fire are a

concern.

148-152-e.pdf 1 1/6/2012 9:51:57 AM

149

T&B Conduit Fittings

Liquatite®Flexible Conduit— Nylon

Type CLFR

A new addition to the Corrlok®System

family of conduits, Type CFLR conduit is

made from a specially modified Nylon

Material with excellent self-extinguishing

characteristics and minimal smoke and

toxic gas gene-ration. CLFR is an excellent

choice for confined inhabited areas such as

Public Transit/Rail Vehicles, Subway

Stations, Tunnels, Etc.

Material:

Halogen Free Nylon 6 UL94 VO

Fitting Pullout

150 lb (1/2” and larger). To be used with

Kopex®fittings of the Corrlok®System.

Listing/Certification

UL Recognized Component, 600 V,

105°C, Vertical Flame, Liquidtight, UV

and Impact Tested.

Standard Colour:

Black. Other colours

available upon request.

Nominal Dimensions Min. Inside Standard

Inside Outside Bend Radius Static Wt. Length

Cat. No. (in.) MM MW in. (mm) in. (mm) in. (mm) kg/30m (m)

CLFR516-30

5/16 12 10 0.370 (9.4) 0.512 (13.0) 1.0 (25.4) 2.5 30

CLFR10-30

3/8 16 12 0.460 (11.7) 0.622 (15.8) 1.5 (38.1) 5.0 30

CLFR11-30

1/2 20 17 0.653 (16.6) 0.826 (21.0) 1.7 (43.2) 7.0 30

CLFR12-30

3/4 25 23 0.854 (21.7) 1.122 (28.5) 2.0 (51.0) 9.5 30

CLFR13-15

1 32 29 1.090 (27.7) 1.358 (34.5) 2.5 (63.5) 13.0 15

CLFR14-15

1-1/4 40 36 1.381 (35.1) 1.673 (42.5) 2.8 (71.1) 16.0 15

CLFR15-15

1-1/2 50 48 1.835 (46.6) 2.145 (54.5) 3.3 (83.8) 19.0 15

Corrlok®System — Type CLFR, Low Fire Hazard

Nominal Dimensions Min. Inside Standard

Inside Outside Bend Radius Static Wt. Length

Cat. No. (in.) MM MW in. (mm) in. (mm) in. (mm) kg/30m (m)

CLR10-30 3/8 16 12 0.452 (11.5) 0.622 (15.8) 0.7 (17.8) 3.4 30

CLR11-30 1/2 20 17 0.633 (16.1) 0.826 (21.0) 0.8 (20.3) 4.4 30

CLR12-30 3/4 25 23 0.865 (22.0) 1.122 (28.5) 1.2 (30.5) 6.7 30

CLR13-15 1 32 29 1.087 (27.6) 1.358 (34.5) 1.4 (35.6) 9.1 15

CLR14-15 1-1/4 40 36 1.420 (36.0) 1.673 (42.5) 2.4 (61.0) 11.0 15

CLR15-15 1-1/2 50 48 1.850 (47.0) 2.145 (54.5) 2.8 (71.1) 16.0 15

CLR17-10 2-1/2 70 70 2.645 (67.0) 3.150 (80.0) 6.3 (160.0) 32.0 10

CLR350-10 3-1/2 95 95 3.600 (91.5) 4.170 (106.0) 8.3 (210.8) 52.0 10

Type CCG

This commercial grade product is

exceptionnally light weight and provides a

cost effective alternative.

Material:

Halogen Free Nylon 16

Working temperatures:

-20°C to 90°C

Standard Colour:

Black. Other colours

available upon request.

To be used with

Kopex®fittings of the

Corrlok®System.

Nominal Dimensions Min. Inside Standard

Inside Outside Bend Radius Static Wt. Length

Cat. No. (in.) MM MW in. (mm) in. (mm) in. (mm) kg/30m (m)

CCG10-30 3/8 16 12 0.452 (11.5) 0.622 (15.8) 1.0 (25.4) 3.0 30

CCG11-30 1/2 20 17 0.633 (16.1) 0.826 (21.0) 1.5 (38.1) 4.0 30

CCG12-30 3/4 25 23 0.870 (22.0) 1.122 (28.5) 1.8 (45.7) 6.0 30

CCG13-15 1 32 29 1.100 (27.9) 1.358 (34.5) 2.0 (51.0) 8.2 15

CCG14-15* 1-1/4 40 36 1.420 (36.0) 1.673 (42.5) 2.4 (61.0) 10.5 15

CCG15-15 1-1/2 50 48 1.850 (47.0) 2.145 (54.5) 2.8 (71.1) 15.3 15

Type CLFR Combustion & Flammability Properties

Test Value

Vertical Burn (Material)

UL94 V-O Rating No Flaming Drips

Vertical Burn (Conduit)

UL360 Pass No Flaming Drips

Flame Spread Index

ASTM E162 1.0 No Flaming Drips

Smoke Generation (Flaming)

ASTM E662 Ds 35@1.5 Min.

(NFPA-258) Ds 85@4.0 Min.

Smoke Generation (Non-Flaming)

ASTM E662 Ds 5@1.5 Min.

(NFPA-258) Ds 24@4.0 Min.

Toxic Gas Generation

BOMBARDIER SMP 800-C Pass

Test data is based on controlled laboratory conditions and does not necessarily reflect

performance in actual fire conditions. Additional product information available upon request.

Corrlok®System — Type CLR, Robotics

Typ e CLR

Very light weight and extremely flexible.

Ideally suited for robotic equipment. This

tubing is intended for applications requiring

continuous, repeated flexible motion.

Material: Halogen Free Nylon 12

Working temperatures

-50°C to 95°C intermitting to 150°C

FIitting Pullout: 65 lb.To be used with

Kopex®fittings of the Corrlok®System.

Listing/ Certification

UL Recognized Component, 600 V,

105°C, Vertical Flame, Liquidtight, UV

and Impact Tested.

Standard Colour: Black. Other colours

available upon request.

Corrlok®System — Type CCG, Commercial Grade

Conduit size

* Not available

148-152-e.pdf 2 1/6/2012 9:51:57 AM

150

T&B Conduit Fittings

Liquatite®Flexible Conduit— Nylon

The Corrlok ®System now features KOPEX ®Fittings

The new, improved slim fitting is great

for use in tight areas and is molded in

high impact Nylon. The two piece

design is easier than ever to assemble

and to re-use. After sliding the backshell

onto the conduit, simply seat the

conduit into the fitting body and click

together. No tools required!

• Fast Installation

• Recognized

• Liquidtight — Equivalent to IP 65 and

NEMA 4

• 360° Retention — High pullout

strength

• Fitting Pullout — Minimum 150 lb

Straight

90° Angle

NPT Threaded Fittings

PG Thread Metric Thread

Thread Thread Thread

Cat. No. (in.) MM MW Size Cat. No. Size Cat. No. Size

CF-140 1/4 10 7 PG-7 - - - -

CF-516 5/16 12 10 PG-9 - - CFM-516 12 mm

CF-10 3/8 16 12 1/2 NPT CFP-10 PG-11 CFM-10 16 mm

CF-11 1/2 20 17 1/2 NPT CFP-11 PG-13.5 CFM-11 20 mm

CF-12 3/4 25 23 3/4 NPT CFP-12 PG-21 CFM-12 25 mm

CF-13 132291NPTCFP-13 PG-29 CFM-13 32 mm

CF-14 1-1/4 40 36 1-1/4 NPT CFP-14 PG-36 CFM-14 40 mm

CF-15 1-1/2 50 48 1-1/2 NPT CFP-15 PG-48 CFM-15 50 mm

Approx. Dimensions

Cat. No. A B C

CF-140 31/32 1-13/32 15/32

CF-516 1-3/32 1-3/8 15/32

CF-10 1-1/16 1-1/2 1/2

CF-11 1-5/16 1-1/2 1/2

CF-12 1-5/8 1-17/32 9/16

CF-13 2 1-21/32 21/32

CF-14 2-5/16 1-13/16 23/32

CF-15 2-13/16 1-13/16 23/32

NPT Threaded Fittings

PG Thread Metric Thread

Thread Unit Standard Thread Thread

Cat. No. (in.) MM MW Size Pack Carton Cat. No. Size Cat. No. Size

CF-140A 1/4 10 7 PG-7 1 - - - - -

CF-516A 5/16 12 10 PG-9 1 - - - CFM-516A 12 mm

CF-20 3/8 16 12 1/2 NPT 25 100 CFP-20 PG-11 CFM-20 16 mm

CF-21 1/2 20 17 1/2 NPT 25 50 CFP-21 PG-13.5 CFM-21 20 mm

CF-22TB 3/4 25 23 3/4 NPT 10 30 CFP-22 PG-21 CFM-22 25 mm

CF-23 132291NPT 1020 CFP-23 PG-29 CFM-23 32 mm

CF-24 1-1/4 40 36 1-1/4 NPT 5 10 CFP-24 PG-36 CFM-24 40 mm

CF-25 1-1/2 50 48 1-1/2 NPT 2 10 CFP-25 PG-48 CFM-25 50 mm

Approx. Dimensions

Cat. No. A B C

CF-140A 1-3/8 19/32 15/32

CF-516A 1-15/32 1-11/16 15/32

CF-20 1-5/8 1-27/32 1/2

CF-21 1-3/4 2 1/2

CF-22 2-3/16 2-5/16 9/16

CF-23 2-1/2 2-9/16 21/32

CF-24 2-3/4 3 23/32

CF-25 3-3/8 3-1/2 23/32

Fitting size

148-152-e.pdf 3 1/6/2012 9:51:58 AM

151

T&B Conduit Fittings

Liquatite®Flexible Conduit— Nylon

Corrlok®System — Flange, Jumbo Straight

Corrlok®System — Type CTC, T Fitting

Corrlok®System — Type TR, T Reducer

Screw

Unit Nominal Dimensions Required

Cat. No. (in.) MM MW Pack A B C D E F

CFF-17 2-1/2 70 70 1 2.362 3.149 3-7/8 2-1/16 4-3/16 17/64

CF-350 3-1/2 95 95 1 2.913 4.251 4-31/32 2-1/16 5-7/32 17/64

Nominal Dimensions Weight

Cat. No. (in.) MM MW A B C D Oz.

CTC-140 1/4 X 3 10 7 2-11/16 1-31/32 1-17/32 1-1/16 0.8

CTC-516 5/16 X 3 12 10 2-11/16 1-31/32 1-17/32 1-1/16 0.8

CTC-10 3/8 X 3 16 12 2-3/4 2 1-1/2 1-7/32 0.9

CTC-11 1/2 X 3 20 17 3-5/32 2-9/32 1-11/16 1-3/8 1.3

CTC-12 3/4 X 3 25 23 3-3/4 2-13/16 2-1/32 1-11/16 2.3

CTC-13 1 X 3 32 29 4-5/16 3-5/16 2-13/32 2 2.3

Trade Size reduce U.S. MM reduce MM

Cat. no. (in.) to Trade (NW) to (NW)

TR-516-140 5/16 ·1/4 12 (10) ·10 (7)

TR-10-516 3/8 ·5/16 16 (12) ·12 (10)

TR-11-516 1/2 ·5/16 20 (17) ·12 (10)

TR-11-10 1/2 ·3/8 20 (17) ·16 (12)

TR-12-516 3/4 ·5/16 25 (23) ·12 (10)

TR-12-10 3/4 ·3/8 25 (23) ·16 (12)

TR-12-11 3/4 ·1/2 25 (23) ·20 (17)

TR-13-11 1·1/2 32 (29) ·20 (17)

Corrlok®System — Flange, Jumbo 90° Angle

Screw

Unit Nominal Dimensions Required

Cat. No. (in.) MM MW Pack A B C D E F

CFF-27 2-1/2 70 70 1 2.362 3.149 3-25/32 5-1/32 4-11/32 17/64

CFF-350A 3-1/2 95 95 1 2.913 4.251 4-31/32 6-17/32 5-11/16 17/64

Both the Flanged Straight and Flanged

90° Angle fittings on this page do not have

threaded ends but are intended

to be mounted as a bulkhead device. Part

numbers include clamps. Seals are

provided for liquidtight connections.

Fitting size

148-152-e.pdf 4 1/6/2012 9:51:58 AM

152

T&B Conduit Fittings

Liquatite®Flexible Conduit— Nylon

Type MB — Mounting Bracket

Nominal Dimensions Weight

Cat. No. (in.) MM MW A B C D E F Oz.

MB-140 1/4 10 7 7/8 1/2 15/16 15/32 5/16 5/32 0.1

MB-516 5/16 12 10 7/8 1/2 15/16 15/32 5/16 5/32 0.1

MB-10TB 3/8 16 12 1-1/16 19/32 1-1/16 17/32 11/32 3/16 0.1

MB-11 1/2 20 17 1-11/32 3/4 1-3/8 11/16 13/32 1/4 0.2

MB-12 3/4 25 23 1-23/32 15/16 1-23/32 13/16 13/32 1/4 0.3

MB-13 1 32 29 2-3/32 1-1/16 2-1/32 15/16 13/32 1/4 0.4

MB-14 1-1/4 40 36 2-17/32 1-9/32 2-15/32 1-1/16 13/32 1/4 0.7

MB-15 1-1/2 50 48 3-3/16 1-1/2 3-1/32 1-9/32 13/32 1/4 1.2

Type FTA — Female Threaded Adapter

Internal

Thread

Cat. No. in. MM MW UNEF

FTA-U12516 1/2-28

FTA-U15516 5/16 12 10 5/8-24

FTA-U18516 3/4-20

FTA-U1810 16 12 3/4-20

FTA-U2310 3/8 15/16-20

FTA-U2311 15/16-20

FTA-U2411 1/2 20 17 1-20

FTA-U2911 13/16-18

FTA-U3411 1-3/8-18

FTA-U2312 15/16-20

FTA-U2912 3/4 25 23

1-3/16-18

FTA-U3412 1-3/8-18

FTA-U3512

1-7/16-18

Type FTA adapters have internal, female

UNEF threads which are sized to match

those of commonly used circular pin

fittings. This component provides a

secure means to attach these quick

disconnect multi-pin fittings to the

Corrlok System.

This assembly eliminates the need for

back shells and heat shrinkable boots

while providing excellent protection to

circuit conductors.

Other thread sizes and types available.

Consult your Regional Sales Office for

further details.

Type PSA — Pro Sensor Adapters

Internal

Thread

Cat. No. in. MM MW UNEF

PSA-M8140

M8 X 1

PSA-M12140

PSA-M18140 1/4

10 7 M12 X 1

PSA-M130140

M18 X 1

M30 X 1.5

PSA-M12516

M12 X 1

PSA-M18516 3/4 16 12

M18 X 1

Type PSA adapters have internal ISO

Metric threads which match those found

on most barrel type proximity sensors.

Like the FTA series, this adapter provides

a means to mate proximity sensors to the

Corrlok System protect the sensor’s

cable.

The adapter is molded in transparent

nylon which permits monitoring of the

LED indicator built into many sensor

designs.

The Corrlok components provide Designers and Electricians with

many options for configuring and installing this raceway

system. These accessories allow a simplified, quick method of

assembly and are perfectly suited for pre-wiring of harnesses.

Corrlok Conduit Size

The Corrlok®System — Accessories

148-152-e.pdf 5 1/6/2012 9:51:59 AM

153

T&B Conduit Fittings

Liquatite®Flexible Conduit— Engineering Information

Conduit Cutting

Benfield Vise

The Benfield cutting vise is

recommended for accurate, straight

cuts in the field. This light weight cast

iron vise can either be bench mounted

or carried in the tool box. The clamping

mechanism securely holds the flexible

conduit while the slots guide a hack

saw to ensure a clean square cut.

Suitable for conduit trade sizes of 3/8”

to 1-1/2”. Works well on other tubings

and materials too.

Order #BLC-1

Weight 2.4 lb

Cutting Flexible Conduits

Proper cutting methods for flexible conduits

are important to ensure a sealed

connection when assembled with intended

fittings. Furthermore, in the case of flexible

conduits containing steel, a clean, square

cut is necessary for establishing a good

connection for continuity of the ground

path.

Hand Cutting in the Field

When using a hand held hack saw, care

should be taken to make a square clean

cut. This can be easily achieved through

the use of the cutting vise shown on this

page. For best results, a blade having

24 to 32 teeth per inch with no-set is

recommended.

Repetitive Production Cutting

It has been our experience that in order to

achieve the best results, a band saw

having a blade with 24 to 32 teeth per inch

at a speed of 300 to 350 feet per minute

should be used. A no-set blade will

produce the cleanest cut. Conduit should

be held and supported in a safe manner.

Abrasive cut-off wheels and chop saws

are not recommended.

Flexible Metal Conduit

Trade Internal Total Area Over

Size Diameter 100 % 2 Wires 31% 2 Wires 40% 1 Wire 53 %

(in.) (in.) (mm) (in.2) (mm2) (in.2) (mm2) (in.2) (mm2) (in.2) (mm2)

5/16 0.312 (7.92) 0.076 (1.9) 0.024 (0.6) 0.031 (0.8) 0.041 (1.0)

3/8 0.375 (9.53) 0.110 (2.8) 0.034 (0.9) 0.044 (1.1) 0.059 (1.5)

7/16 0.437 (11.10) 0.150 (3.8) 0.046 (1.2) 0.060 (1.5) 0.079 (2.0)

1/2 0.625 (15.88) 0.307 (7.8) 0.095 (2.4) 0.123 (3.1) 0.163 (4.1)

3/4 0.812 (20.62) 0.518 (13.2) 0.161 (4.1) 0.207 (5.3) 0.274 (7.0)

1 1.000 (25.40) 0.785 (19.9) 0.243 (6.2) 0.314 (8.0) 0.416 (10.6)

1-1/4 1.250 (31.75) 1.227 (31.2) 0.380 (9.7) 0.491 (12.5) 0.650 (16.5)

1-1/2 1.500 (38.10) 1.767 (44.9) 0.548 (13.9) 0.707 (18.0) 0.937 (23.8)

2 2.000 (50.80) 3.142 (79.8) 0.974 (24.7) 1.257 (31.9) 1.665 (42.3)

2-1/2 2.500 (63.50) 4.909 (124.7) 1.522 (38.7) 1.964 (49.9) 2.602 (66.1)

3 3.000 (76.20) 7.069 (179.5) 2.191 (55.7) 2.827 (71.8) 3.746 (95.2)

3-1/2 3.500 (88.9) 9.621 (244.4) 2.983 (75.8) 3.848 (97.8) 5.099 (129.5)

4 4.000 (101.60) 12.566 (319.2) 3.896 (98.9) 5.027 (127.7) 6.660 (169.2)

Liquidtight Flexible Metal Conduit

Trade Internal Total Area Over

Size Diameter 100 % 2 Wires 31% 2 Wires 40% 1 Wire 53 %

(in.) (in.) (mm) (in.2) (mm2) (in.2) (mm2) (in.2) (mm2) (in.2) (mm2)

3/8 0.484 (12.29) 0.184 (4.7) 0.057 (1.4) 0.074 (1.9) 0.098 (2.5)

1/2 0.622 (15.80) 0.304 (7.7) 0.094 (2.4) 0.122 (3.1) 0.161 (4.1)

3/4 0.820 (20.83) 0.528 (13.4) 0.164 (4.2) 0.211 (5.4) 0.280 (7.1)

1 1.041 (26.44) 0.851 (21.6) 0.264 (6.7) 0.340 (8.6) 0.451 (11.5)

1-1/4 1.380 (35.05) 1.496 (38.0) 0.464 (11.8) 0.598 (15.2) 0.793 (20.1)

1-1/2 1.575 (40.01) 1.948 (49.5) 0.604 (15.3) 0.779 (19.8) 1.033 (26.2)

2 2.020 (51.31) 3.205 (81.4) 0.993 (25.2) 1.282 (32.6) 1.699 (43.1)

2-1/2 2.480 (62.99) 4.831 (122.7) 1.497 (38.0) 1.932 (49.1) 2.560 (65.0)

3 3.070 (77.98) 7.402 (188.0) 2.295 (58.3) 2.961 (75.2) 3.923 (99.6)

3-1/2 3.500 (88.90) 9.621 (244.4) 2.983 (75.8) 3.848 (97.8) 5.099 (129.5)

4 4.000 (101.60) 12.566 (319.2) 3.896 (98.9) 5.027 (127.7) 6.660 (169.2)

Conduit Wire Fill Charts

Per Canadian Electrical Code

CONFITMRO_EN_ALL.pdf 153 11/28/2011 11:05:48 AM

154

T&B Conduit Fittings

Liquatite®Flexible Conduit— Engineering Information

Common Conversion

Length

English Measure Metric Measure

1 Foot 0.305 Meters

1 Meter 3.281 Feet

1 Inch 25.4 Millimeters

1 Millimeter 0.039 Inches

1 Inch 2.54 Centimeters

1 Centimeter 0.394 Inches

Weight

English Measure Metric Measure

1 Pound 454 Grams

1 Pound 0.454 Kilograms

1 Kilogram 2.205 Pounds

1 Gram 0.035 Ounces

1 Ounce 28.349 Grams

Temperature

C° = Degrees Centigrade

F° = Degrees Farenheit

C° = (F° - 32) 5 F° = (C° x 9) + 32

9 5

Knockout Hole Sizes

NPT Threaded Fittings

Fitting Knockout Thread Diameter

(in.) (in.) in. (mm)

3/8

1/2 NPT (12.7) 7/8 (22.2)

1/2 1/2 NPT (12.7) 7/8 (22.2)

3/4 3/4 NPT (19.1) 13/32 (27.8)

1 1 NPT (25.4) 123/64 (34.5)

1-1/4 1-1/4 NPT (31.8) 1-23/32(34.5)

1-1/2 1-1/2 NPT (38.1) 2 (50.8)

2 2 NPT (50.1) 2-1/2 (63.5)

Conduit Wire Fill Charts (continued)

Per Canadian Electrical Code

Liquidtight Non-Metallic Conduit — Type A

Total Trade Internal Total Area Over

Size Diameter 100 % 2 Wires 31% 2 Wires 40% 1 Wire 53 %

(in.) (in.) (mm) (in.2) (mm2)(in.

2) (mm2)(in.

2) (mm2) (in.2) (mm2)

3/8 0.485 (12.32) 0.185 (4.7) 0.057 (1.5) 0.074 (1.9) 0.098 (2.5)

1/2 0.620 (15.75) 0.302 (7.7) 0.094 (2.4) 0.121 (3.1) 0.160 (4.1)

3/4 0.855 (20.70) 0.522 (13.3) 0.162 (4.1) 0.209 (5.3) 0.276 (7.0)

1 1.030 (26.16) 0.833 (21.2) 0.258 (6.6) 0.333 (8.5) 0.442 (11.2)

1-1/4 1.370 (34.80) 1.474 (37.4) 0.457 (11.6) 0.590 (15.0) 0.781 (19.8)

1-1/2 1.585 (40.26) 1.973 (50.1) 0.612 (15.5) 0.789 (20.0) 1.046 (26.6)

2 2.045 (51.94) 3.285 (83.4) 1.018 (25.9) 1.314 (33.4) 1.741 (44.2)

Liquidtight Non-Metallic Conduit — Type B

Total Trade Internal Total Area Over

Size Diameter 100 % 2 Wires 31% 2 Wires 40% 1 Wire 53 %

(in.) (in.) (mm) (in.2) (mm2)(in.

2) (mm2)(in.

2) (mm2)

3/8 0.485 (12.32) 0.185 (4.7) 0.057 (1.5) 0.074 (1.9) 0.098 (2.5)

1/2 0.620 (15.75) 0.302 (7.7) 0.094 (2.4) 0.121 (3.1) 0.160 (4.1)

3/4 0.855 (20.70) 0.522 (13.3) 0.162 (4.1) 0.209 (5.3) 0.276 (7.0)

1 1.030 (26.16) 0.833 (21.2) 0.258 (6.6) 0.333 (8.5) 0.442 (11.2)

1-1/4 1.370 (34.80) 1.474 (37.4) 0.457 (11.6) 0.590 (15.0) 0.781 (19.8)

1-1/2 1.585 (40.26) 1.973 (50.1) 0.612 (15.5) 0.789 (20.0) 1.046 (26.6)

2 2.045 (51.94) 3.285 (83.4) 1.018 (25.9) 1.314 (33.4) 1.741 (44.2)

CONFITMRO_EN_ALL.pdf 154 11/28/2011 11:05:48 AM

155

T&B Conduit Fittings

Liquatite®Flexible Conduit

All standard lengths packaged in

specially-designed, functional cartons

to eliminate knots and tangles. These

compact cartons save storage and

warehouse space, making handling

easier. Each carton label is clearly

marked and colour coded with conduit

size, type, colour, and footage as well as

the NEMA and NAED bar code standards.

Special Cut Lengths Available

Thomas & Betts can supply “cut-to-

length” orders. Consult your Regional

Sales Office for details.

LT - LOR - EF - LA - CSA - ALT - AT

ATLA - ATX - CEA - ZHLA - LAS

EMS - EMSP - NMC - NMT - ACEA

Standard Dimensions and Packaging — Types Reel Sizes

Trade Size Inner dia. Outer Dia.

(in.) Type Min. Max. Min. Max.

1/4 - 0.245 0.265 0.450 0.470

5/16 - 0.385 0.405 0.570 0.590

3/8 10 0.484 0.504 0.690 0.710

1/2 11 0.622 0.642 0.820 0.840

3/4 12 1.820 0.840 1.030 1.050

1 13 1.041 1.066 1.290 1.315

1-1/4 14 1.380 1.410 1.630 1.660

1-1/2 15 1.575 1.600 1.865 1.900

2 16 2.020 2.045 2.340 2.375

2-1/2 17 2.480 2.505 2.840 2.875

3 18 3.070 3.100 3.460 3.500

1-1/2 350 3.500 3.540 3.960 4.000

4 19 4.000 4.040 4.460 4.500

5 500 4.975 5.035 5.505 5.565

6 600 6.015 6.075 6.565 6.625

Trade

Size 58” 42” 31” 31” Special 24”

(in.) LT-LA-EF LT-LA-EF LT LA EF LT LA EF LT-LA-EF

3/8 6,000 - 1,000 1,000 1,000 - - -

500

1/2 4,500 - 1,000 1,000 1,000 - -

-500

3/4 2,500 1,000 500 500 500 - -

1 1,500 - 400 400 400 - -

1-1/4 1,000 - 200 - 200 - 200

1-1/2 750 - - - - 150 150

150 -

2 500 - - - - 100 100

100 -

2-1/2 275 - - - - - -

3 175 - - - - - -

3-1/2 175 - - - - - -

4 100 - - - - - -

5 - --- -- -

6 - --- -- -

Approx. Reel Dimensions in. (mm)

“A” “B” “C”

24 (610) 19-1/2 (495) 12 (305)

31 (760) 19-1/2 (495) 12 (305)

31 (760) Special 19-1/2(495) 15 (381)

42 (1029) 20 (508) 24 (610)

58 (1421) 29-1/2 (749) 28 (711)

Trade Standard Standard

Size Carton Carton

Cat. No. (in.) All types Type LNM-P

038 3/8 30 75

050 1/2 30 60

075 3/4 30 50

100 13030

125 1-1/4 15 30

150 1-1/2 15 15

200 21515

250 2-1/2 8 -

300 38-

350 3-1/2 8 -

400 48-

500 58-

600 68-

Cartons

CONFITMRO_EN_ALL.pdf 155 11/28/2011 11:05:49 AM

156

T&B Conduit Fittings

Conduit Dimensional Data

Rigid Metal Conduit (Extract from CSA C22.2 No. 45.1)

Metric Threads Nominal Nominal External External Wall Wall

Trade Designator Imperial per Internal Dia. Internal Dia. Diameter Diameter Thickness Thickness

(As per CEC 2009) Trade Size in. (mm) (in.) (mm) (in.) (mm) (in.)

12 3/8 18 12.52 0.493 17.1 0.675 2.31 0.091

16 1/2 14 16.05 0.632 21.3 0.840 2.64 0.104

21 3/4 14 21.23 0.836 26.7 1.050 2.72 0.107

27 1 11-1/2 27.60 1.063 33.4 1.315 3.20 0.126

35 1-1/4 11-1/2 35.41 1.394 42.2 1.660 3.38 0.133

41 1-1/2 11-1/2 41.25 1.624 48.3 1.900 3.51 0.138

53 2 11-1/2 52.91 2.083 60.3 2.375 3.71 0.146

63 2-1/2 8 63.22 2.489 73.0 2.875 4.90 0.193

78 3 8 78.49 3.090 88.9 3.500 5.21 0.205

91 3-1/2 8 90.69 3.570 101.6 4.000 5.46 0.215

103 4 8 102.87 4.050 114.3 4.500 5.72 0.225

129 5 8 128.85 5.073 141.3 5.563 6.22 0.245

155 6 8 154.76 6.093 168.3 6.625 6.76 0.266

Knockout (sliphole) Sizes for Electrical Conduits and Fittings

Metric Knockout Diameter

Trade Designator

Diameter Imperial Minimum Nominal Maximum

(As per CEC 2009) Trade Size (mm) (in.) (mm) (in.) (mm) (in.)

16 1/2 21.84 0.860 22.33 0.875 23.01 0.906

21 3/4 27.79 1.094 28.17 1.109 28.96 1.140

27 1 34.52 1.359 34.93 1.375 35.71 1.406

35 1-1/4 43.66 1.719 44.04 1.734 44.83 1.765

Electrical Metallic Tubing (Extract from CSA C22.2 No. 83.1)

Metric Nominal Nominal Outside Outside Wall Wall

Trade Designator Imperial Internal Dia. Internal Dia. Diameter Diameter Thickness Thickness

(As per CEC 2009) Trade Size (mm) (in.) (mm) (in.) (mm) (in.)

16 1/2 15.80 0.622 217.9 0.705 1.07 0.042

21 3/4 20.93 0.824 23.4 0.921 1.24 0.049

27 1 26.64 1.049 29.5 1.161 1.45 0.057

35 1-1/4 35.05 1.380 38.4 1.512 1.65 0.065

41 1-1/2 40.89 1.610 44.2 1.740 1.65 0.065

53 2 52.50 2.067 55.8 2.197 1.65 0.065

63 2-1/2 69.37 2.731 73.0 2.874 1.83 0.072

78 3 85.24 3.355 88.9 3.500 1.83 0.072

91 3-1/2 97.38 3.834 101.6 4.000 2.11 0.083

103 4 110.08 4.334 114.3 4.500 2.11 0.083

CONFITMRO_EN_ALL.pdf 156 11/28/2011 11:05:49 AM

157

T&B Conduit Fittings

Conduit Dimensional Data

Flexible Metal Conduit (Extract from CSA C22.2 No. 56)

Minimum Minimum Maximum Maximum

Imperial Internal Diameter Internal Diameter External Diameter External Diameter

Trade Size (mm) (in.) (mm) (in.)

5/16 7.92 0.312 12.95 0.510

3/8 9.52 0.375 15.49 0.610

7/16 11.10 0.437 17.15 0.675

1/2 15.88 0.625 23.37 0.920

3/4 20.62 0.812 28.07 1.105

1 25.40 1.000 35.05 1.380

1-1/4 31.75 1.250 41.40 1.630

1-1/2 38.10 1.500 49.53 1.950

2 50.80 2.000 62.23 2.450

2-1/2 63.50 2.500 77.72 3.060

3 76.20 3.000 90.42 3.560

3-1/2 88.90 3.500 103.12 4.060

4 101.60 4.000 115.82 4.560

Liquidtight Flexible Conduit (Extract from CSA C22.2 No. 56)

Minimum Minimum Minimum Minimum Maximum Maximum

Imperial Internal Dia. Internal Dia. Overall Diameter Overall Diameter Overall Diameter Overall Diameter

Trade Size (mm) (in.) (mm) (in.) (mm) (in.)

3/8 12.29 0.484 17.5 0.690 18.0 0.710

1/2 15.80 0.622 20.8 0.820 21.3 0.840

3/4 20.83 0.820 25.2 1.030 26.7 1.050

1 26.44 1.041 32.8 1.290 33.4 1.315

1-1/4 35.05 1.380 41.4 1.630 42.2 1.660

1-1/2 40.01 1.575 47.4 1.865 48.3 1.900

2 51.31 2.020 59.4 2.340 60.3 2.375

2-1/2 62.99 2.480 72.1 2.840 73.0 2.875

3 77.98 3.070 87.9 3.460 88.9 3.500

3-1/2 88.90 3.500 100.6 3.960 101.6 4.000

4 101.60 4.000 113.3 4.460 114.3 4.500

Flexible Liquidtight Nonmetallic Conduit (Extract from CSA C22.2 No. 227.2)

Minimum Minimum Maximum Maximum

Imperial Internal Dia. Internal Dia. Internal Dia. Internal Dia. Minimum Dia. Minimum Dia. Maximum Dia. Maximum Dia.

Trade Size (mm) (in.) (mm) (in.) (mm) (in.) (mm) (in.)

3/8 12.32 0.485 13.83 0.505 19.18 0.755 19.69 0.775

1/2 15.75 0.620 16.26 0.640 23.11 0.910 23.62 0.930

3/4 20.70 0.815 21.21 0.835 29.21 1.150 29.72 1.170

1 26.16 1.030 27.05 1.065 35.94 1.415 36.58 1.440

1-1/4 34.80 1.370 35.43 1.395 45.72 1.800 46.36 1.825

1-1/2 40.26 1.585 41.15 1.620 51.94 2.045 52.83 2.080

2 51.94 2.045 52.83 2.080 66.17 2.605 67.06 2.640

CONFITMRO_EN_ALL.pdf 157 11/28/2011 11:05:49 AM

158

T&B Conduit Fittings

Conduit—Chemical Resistance Guide

NYLONS NYLONS

CHEMICAL % PVC PU 6 12 CHEMICAL % PVC PU 6 12

ASTM Fuel A CA

ASTM Fuel B DB

ASTM Fuel C B

ASTM Oil No. 1 BB

ASTM Oil No. 2 B

ASTM Oil No. 3 CBAA

Acetaldehyde 40% D B A

Acetamide 50% A A

Acetate Solvents D

Acetic Acid (Glacial) CDDC

Acetic Acid 40% D D C

Acetic Acid 10% B C B

Acetic Anhydride DDB

Acetone DDAA

Acetyl Bromide C

Acetyl Chloride C

Acetylene BAA

Acrylonitrite A

Adipic Acid A

Alcohols AA

Alcohols (Aliphatic) C

Alkalies A

Allyl Alcohol BB

Aluminium Salts AA

Aluminum Chloride AB

Aluminum Sulfate (Alums) AB

Aluminum Sulfide B

Alums BA

Ammonia BAA

Ammonia 10% A A

Ammonia (Anhydrous Liquids) D

Ammonia (Aqueous) A

Ammoniated Latex A

Ammonium Acetate B

Ammonium Carbonate B

Ammonium Chloride 10% A A

Ammonium Chloride A

Ammonium Hydroxide AA

Ammonium Nitrate B

Ammonium Persulfate B

Ammonium Salts BA

Ammonium Sulfate B

Ammonium Sulfide B

Ammonium Thicyanide B

Amyl Acetate DDAB

Amyl Alcohol CAA

Amyl Chloride C

Aniline DBB

Aniline Hydrochloride D

Aniline Oils D

Animal Fats & Oils AB

Aniseed Oil AA

Anthracene D

Antifreeze Compounds AA

Antimony Salts B

Aqua Regia DD

Aromatic Fuels D

Aromatic Hydrocarbons D

Arsenic Salts A

Asphalt D

Attar of Roses AA

Banana Oil D

Barium Carbonate B

Barium Chloride A

Barium Hydroxide AB

Barium Salts AA

Barium Sulfide A

Battery Acid 30% C B

Benzaldehyde 0.3 % A A

Benzaldehyde DCB

Benzene DDAA

Benzine (Petroleum Ether) CB

Benzoic Acid CBB

Benzole AA

Benzyl CC

Bitumen AA

Borax AAA

Bordeaux Mixture A

Boric Acid ABBA

Brake Fluid AA

Brake Fluid A B

Brine A

Bromine BCC

Bunker Oil B

Butane BAA

Butanol AB

Butyl Acetate DDAA

Butyl Alcohol BB

Butylene Glycol BA

Butyric Acid BA

Calcium Carbonate B

Calcium Chloride 10% A A

Calcium Chloride 20% A B D C

Calcium Hydroxide AB

Calcium Hypochlorite A

Calcium Nitrate B

Calcium Sulfate B

Camphor AA

Carbolic Acid (Phenol) B

Carbon Dioxide AA

Carbon Disulfide DBAA

Carbon Tetrachloride DDAB

Carbonic Acid A

Casein A

Castor Oil AB

Catechol 6% C B

Caustic Soda 40% A A A

Cello - Solv D

Chlorinated Hydrocarbons D

Chlorinated Lime DD

Chlorine BDD

Chlorine (water solution) < 5% C C B

Chlorine Gas (dry & wet) < 5% D C B

Chloroacetic Acid CDD

Chlorobenzene DAC

Chlorobromomethane BB

Chloroform DCC

Chrome Baths DC

Chromic Acid 1% D C B

Chromic Acid 10% B D D C

A- Good to excellent

B- Fair to Good

C- Fair to Limited

D- Unsatisfactory

PVC- Polyvinyl chloride

PU- Polyurethane

CONFITMRO_EN_ALL.pdf 158 11/28/2011 11:05:49 AM

159

T&B Conduit Fittings

Conduit—Chemical Resistance Guide

NYLONS NYLONS

CHEMICAL % PVC PU 6 12 CHEMICAL % PVC PU 6 12

C (cont’d)

Chromic /Sulfuric Acid DD

Chromium Potassium Sulfate B

Chromium Salts AA

Citric Acid AB

Coal Tar D

Coconut Oil CAA

Copper Salts 10% A A

Corn Oil A

Cottonseed Oil CB

Creosote D

Cresol CDDD

Cresylic Acid D

Cupric Chloride B

Cupric Nitrate B

Cupric Sulfate B

Cyclohexane BAA

Cyclohexanol AA

Cyclohexanone DAA

DDT Weed Killer A

DOP D

DTE Oil B

Decalin AA

Degreasing Fluids D

Detergents (dishwashing) AA

Di Iso Cyanate C

Di Methyl Formamide D

Di Methyl Hydrazine D

Di-isodecyl Phthalate D

Dibutyl Ether B

Dibutyl Phthalate DDAA

Dichlorobenzene C

Diesel Fuel DBAA

Diesel Oils CAA

Diester Oil B

Diethyl Ether AAA

Diethylene Glycol B

Dimethyl Acetamide D

Dimethyl Formamide DAB

Dioctyl Phthalate DAA

Dioxane AA

Dodecyl Mercaptan B

Dow General Weed Killer (H20) B

Dow General Weed Killer (Phenol) D

Dowtherm D

Edible Fats and Oils AA

Esters D

Ether DBAA

Ethyl Acetate DAA

Ethyl Alcohol CBAA

Ethyl Bromide C

Ethyl Chloride C

Ethylene Chloride AB

Ethylene Dichloride D

Ethylene Glycol BB

Fatty Acids AAA

Ferric Chloride AB

Ferric Nitrate B

Ferric Sulfate A

Ferrous Chloride AB

Ferrous Sulfate AB

Flourochlorohydrocarbons AA

Formaldehyde 40% D B C B

Formalin BB

Formamide BB

Formic Acid 85% D C

Formic Acid 10% A D C C

Formic Acid 40% D C

Freon CAA

Freon 12 AA

Freons D

Fuel Oil BBAA

Furfurol CBB

Gallic Acid A

Gasoline - 100 Octane CB

Glycerine ABAA

Glycol AA

Glycolic Acid B

Grease AB

Green Sulfate Liquor A

Heptachlor in Petroleum Solvents A

Heptane CBAA

Hexane CBAA

Hydraulic Fluid AA

Hydraulic Fluids -Ester Base DAA

Hydraulic Fluids-Petroleum Base CAA

Hydrazine D

Hydrobromic Acid AB

Hydrocarbon Oil B

Hydrochloric Acid 40% C

Hydrochloric Acid 1% C B

Hydrochloric Acid 10% A B D C

Hydrocyanic Acid B

Hydrofluoric Acid B

Hydrofluoric Acid 70% C

Hydrofluoroboric Acid A

Hydrofluorosilicic Acid A

Hydrogen A

Hydrogen Chloride < 2% C B

Hydrogen Chloride > 2% D C

Hydrogen Fluoride 40% D D

Hydrogen Peroxide 2% C B

Hydrogen Peroxide 30% D D

Hydrogen Peroxide 10%ABCB

Hydrogen Sulfide < 5% C A A

Hydrolodic Acid B

Ink CAA

Iodine Solution B

Iron Salts -Acid Soln. 20% D C

Iron Salts -Neut. Soln. 20% A A

Isooctane CBAA

Isopropanal B

Isopropyl Acetate D

Isopropyl Alcohol BAB

A- Good to excellent

B- Fair to Good

C- Fair to Limited

D- Unsatisfactory

PVC- Polyvinyl chloride

PU- Polyurethane

CONFITMRO_EN_ALL.pdf 159 11/28/2011 11:05:49 AM

160

T&B Conduit Fittings

Conduit—Chemical Resistance Guide

NYLONS NYLONS

CHEMICAL % PVC PU 6 12 CHEMICAL % PVC PU 6 12

P-4 Oil C

Jet Fuels (JP-3,4, and 5) C

Kerosene CBAA

Ketones D

Lacquer Thinners D

Lactic Acid 50% C B

Lactic Acid 5% B B A

Lactic Acid 90% D B

Lanolin AA

Lead Acetate B

Lead Salts AA

Linseed Oil ABAA

Lox B

Lubricating Oils, Greases, Soaps ABAA

MIL-D-5606 Oil C

MIL-L-7808 Oil B

Magnesium Chloride A

Magnesium Hydroxide 10% A A A

Magnesium Salts 10% B A A

Magnesium Sulfate A

Malathion 50 in Aromatics D

Malic Acid AC

Mercury AAA

Mercury Salts AA

Methanol BAB

Methyl Acetate D

Methyl Alcohol C

Methyl Bromide D

Methylene Chloride DDBC

Methyl Ethyl Ketone DDAA

Mineral Oil AAAA

Monochlorobenzene D

Motor Fuels AA

Motor Oil 20W BAA

Muriatic Acid (See Hydrochloric Acid)

Naphtha CB

Naphthalene DAA

Natural Gas B

Nickel Salts CAA

Nitric Acid DDD

Nitric Acid 10% A

Nitric Acid 35% A

Nitric Acid 70% D

Nitrobenzene DBB

Nitrogen A

Nitromethane AA

Octane AA

Oil of Turpentine AA

Oleic Acid ABAA

Oleum DDD

Oxalic Acid 10% A A B A

Oxygen AAA

Oxygen - Liquid D

Ozone <1 PPM A A A

Paint DB

Paint Thinners D

Palmitic Acid A

Paper Chemicals A

Paraffin Oil AA

Pentachlorophenol in Oil B

Pentane C

Perchloric Acid D

Perchloroethylene DDAA

Petroleum BAA

Petroleum Ether CAA

Petroleum Spirits D

Phenol BDCC

Phenyl Ethyl Alcohol BC

Phosphoric Acid 10% B C B

Phosphoric Acid 50% C C

Phosphoric Acid 85% A

Photographic Developer A

Phthalates D

Pitch B

Plasticizers (Phthalates, Phosphates) AA

Polyester Resin with Styrene AA

Potash AA

Potassium Bromide 10% A A

Potassium Chlorate 7% C B

Potassium Chlorate 5% B A

Potassium Cyanide B

Potassium Hydroxide A

Potassium Hydroxide 50% A A

Potassium Iodide 10% A A

Potassium Nitrate 10% A A

Potassium Permanganate 1% D D

Potassium Salts B

Potassium Sulfate 10% A A

Propane ABAA

Propanol AB

Propyl Alcohol BC

Propylene Glycol B

Pydraul D

Pydraul Oil D

Pyridine AA

Resorcinol DD

Ritchfield “A” Weed Killer C

SEA No. 10 Oil B

Salicylic Acid AA

Salt AA

Seawater ABAA

Silicic Acid B

Silicone Oil AAA

Silver Nitrate CB

Silver Salts AA

Skydrol Oil -Type B DDAA

Soap B

Soap Solution 10% A A

Sodium Acetate B

Sodium Bicarbonate BAA

Sodium Bisulfite 10% B A A

Sodium Borate B

Sodium Bromide 10% B A

A- Good to excellent

B- Fair to Good

C- Fair to Limited

D- Unsatisfactory

PVC- Polyvinyl chloride

PU- Polyurethane

CONFITMRO_EN_ALL.pdf 160 11/28/2011 11:05:49 AM

161

T&B Conduit Fittings

Conduit—Chemical Resistance Guide

NYLONS NYLONS

CHEMICAL % PVC PU 6 12 CHEMICAL % PVC PU 6 12

Sodium Carbonate B

Sodium Carbonate 10% A A

Sodium Chlorate B

Sodium Chloride BAA

Sodium Chlorite 5% C C

Sodium Cyanide AB

Sodium Dichromate B

Sodium Ferrocyanide B

Sodium Fluoride B

Sodium Hydrosulfiite B

Sodium Hydroxide B

Sodium Hydroxide 40% A A

Sodium Hydroxide 50% A

Sodium Hypochlorite 5% C B

Sodium Nitrate B

Sodium Nitrate 10% A A

Sodium Nitrite 5% C B

Sodium Perborate 5% B A

Sodium Phosphate 10% A A

Sodium Silicate B

Sodium Sulfate 10% A A

Sodium Sulfide 10% B A A

Sodium Sulfite 10% A A

Sodium Thiosulfite AA

Solvent Naphtha AA

Solvesso D

Stoddard Solvent D

Styrene DB

Sulfur AA

Sulfur Dioxide <5% B C B

Sulfur Dioxide (Liquid) D

Sulfuric Acid 2% D B

Sulfuric Acid 10% D B

Sulfuric Acid 20% D

Sulfuric Acid 25% D C

Sulfuric Acid 50% A

Sulfuric Acid 98% D

Sulfurous Acid B

Tall Oil D

Tallow AA

Tannic Acid AC

Tar AA

Tartaric Acid 10% B A A

Tea AA

Tetra Ethyl Lead D

Tetra Hydro Furan DAA

Tetraline AA

Thionyl Chloride DD

Tin Salts B

Titanium Salts B

Toluene DDAA

Toluol D

Transformer Oil CAA

Transmission Oil B

Trichloroethane D

Trichlorethylene DBB

Trichloroacetic Acid D

Trichloroethylene D

Tricresyl Phosphate D

Tricresyl Phosphate (Skydrol) D

Triethanol Amine CB

Trisodium Phosphate B

Tung Oil C

Turpentine CBAA

Urea 20% B A A

Varnish B

Varsol D

Vaseline AA

Vegetable Oils and Juices ABAA

Vinegar ABA

Vinyl Chloride D

Water AAA

Water 23°C B

Water 70°C B

Wax AA

Wood Preservatives D

Xylene DCAA

Xylols D

Zinc Chloride 10% A B B A

Zinc Sulfate AB

CHEMICAL Resistance Chart- Type ATX

Thermoplastic Rubber jacket

% Tensile % % Volume

Test Method Strength Elongation Increase

ASTM #2 OIL

UL - 1581 7 days/60°C 90 98 N/A

4 days/100°C 66 70 N/A

18 hrs/120°C 45 40 N/A

Brake Fluid

ASTM D - 471 72 hrs/100°C 80 90 -7

Ethylene Glycol

ASTM D - 471 72 hrs./100°C 95 90 2

Methanol

ASTM D - 471 72 hrs./ 100°C 95 90 0

Silicone Oil

ASTM D - 471 72 hrs./100°C 100 80 -14

5 % Salt Water

ASTM D - 471 72 hrs./100°C 80 100 1

Vegetable Oil

ASTM D - 471 18 hrs./120°C 60 70 N/A

Animal Oil

ASTM D - 471 18 hrs./120°C 70 75 N/A

10W-40 Motor Oil

ASTM D - 471 72 hrs./100°C 50 55 25

Gasoline

ASTM D - 471 72 hrs./ 100°C 40 35 17

Transmission Oil

ASTM D - 471 72 hrs./100°C 50 50 32

Freon2

ASTM D - 471 72 hrs./50°C 93 84 N/A

This information is provided as a guide line only. No guarantee is

implied. Results are based on controlled laboratory tests and not on

installed end-product applications. Electri-Flex recommends that

samples be exposed to and observed in actual service

conditions for extreme or unusual situations.

A- Good to excellent

B- Fair to Good

C- Fair to Limited

D- Unsatisfactory

PVC- Polyvinyl chloride

PU- Polyurethane

CONFITMRO_EN_ALL.pdf 161 11/28/2011 11:05:49 AM

Alphanumeric Index

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

162

ABR038-15 143

ABR038-30 143

ABR038-300 143

ABR038-8 143

ABR050-15 143

ABR050-30 143

ABR050-300 143

ABR050-8 143

ABR075-15 143

ABR075-150 143

ABR075-30 143

ABR075-8 143

ABR100-120 143

ABR100-15 143

ABR125-120 143

ABR125-15 143

ABR150-8 143

ABR150-90 143

ABR200-45 143

ABR200-8 143

ABR250-8 143

ABR300-8 143

ABR350-8 143

ABR400-8 143

ABRH038 143

ABRH050 143

ABRH075 143

ABRH100 143

ABRH125 143

ABRH150 143

ABRH200 143

ABRH250 143

ABRH300 143

ABRH400 143

ABRH716 143

ACEA038 138

ACEA038-60 138

ACEA050 138

ACEA050-30 138

ACEA050-300 138

ACEA075 138

ACEA075-150 138

ACEA075-30 138

ACEA075-45 138

ACEA100 138

ACEA100-120 138

ACEA100-30 138

ACEA125 138

ACEA125-15 138

ACEA125-75 138

ACEA150 138

ACEA150-15 138

ACEA150-45 138

ACEA200 138

ACEA200-15 138

ACEA200-30 138

ACEA250 138

ACEA250-8 138

ACEA300 138

ACEA300-8 138

ACEA400 138

ACEA400-8 138

ACEA500 138

ACEA600 138

ALT038-150 136

ALT038-30 136

ALT038-300 136

ALT050-150 136

ALT050-30 136

ALT050-300 136

ALT075-150 136

ALT075-30 136

ALT075-300 136

ALT100-120 136

ALT100-30 136

ALT125-15 136

ALT125-60 136

ALT150-15 136

ALT150-45 136

ALT200-15 136

ALT200-30 136

ALT250-8 136

ALT350-8 136

ALT400-8 136

ALT500-8 136

ALT600-8 136

AT038-150 135

AT038-30 135

AT038-300 135

AT050-150 135

AT050-30 135

AT050-300 135

AT075-150 135

AT075-30 135

AT075-300 135

AT100-120 135

AT100-30 135

AT125-15 135

AT125-60 135

AT150-15 135

AT150-45 135

AT200-15 135

AT200-30 135

AT250-8 135

AT300-8 135

AT350-8 135

AT400-8 135

AT500-8 135

AT600-8 135

ATLA038-150 134

ATLA038-30 134

ATLA038-300 134

ATLA050-150 134

ATLA050-30 134

ATLA050-300 134

ATLA075-150 134

ATLA075-30 134

ATLA075-300 134

ATLA100-120 134

ATLA100-30 134

ATLA125-15 134

ATLA125-60 134

ATLA150-15 134

ATLA150-45 134

ATLA200-15 134

ATLA200-30 134

ATLA250-8 134

ATLA300-8 134

ATLA350-8 134

ATLA400-8 134

ATX038-150 135

ATX038-30 135

ATX038-300 135

ATX050-150 135

ATX050-30 135

ATX050-300 135

ATX075-150 135

ATX075-30 135

ATX075-300 135

ATX100-120 135

ATX100-30 135

ATX125-15 135

ATX125-60 135

ATX150-15 135

ATX150-45 135

ATX200-15 135

ATX200-30 135

ATX250-8 135

ATX300-8 135

ATX400-8 135

BG050-14-20 14

BG050-14-4 14

BG075-14-20 14

BG075-14-4 14

BG100-14-20 14

BG100-14-4 14

BG125-14-20 14

BG150-14-20 14

BG200-14-20 14

CONFITMRO_EN_ALL.pdf 162 11/28/2011 11:05:50 AM

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

Alphanumeric Index

163

BG250-14-20 14

BG250-6-40 14

BG300-14-20 14

BG300-6-40 14

BG350-14-20 14

BG350-6-40 14

BG400-14-20 14

BG400-6-40 14

BG500-14-20 14

BG500-6-40 14

BG600-14-20 14

BG600-6-40 14

BGA050-14-20 14

BGA050-14-4 14

BGA075-14-20 14

BGA075-14-4 14

BGA100-14-20 14

BGA100-14-4 14

BGA125-14-20 14

BGA150-14-20 14

BGA200-14-20 14

BGA250-14-20 14

BGA250-6-40 14

BGA300-14-20 14

BGA300-6-40 14

BGA350-14-20 14

BGA350-6-40 14

BGA400-14-20 14

BGA400-6-40 14

BGA500-14-20 14

BGA500-6-40 14

BGA600-14-20 14

BGAT600-6-40 14

BR038 142

BR038-15 142

BR038-30 142

BR038-300 142

BR038-75 142

BR038-8 142

BR050 142

BR050-15 142

BR050-30 142

BR050-300 142

BR050-8 142

BR075 142

BR075-15 142

BR075-150 142

BR075-30 142

BR075-8 142

BR100 142

BR100-120 142

BR100-15 142

BR125 142

BR125-120 142

BR125-15 142

BR150 142

BR150-8 142

BR150-90 142

BR200 142

BR200-45 142

BR200-8 142

BR250 142

BR250-8 142

BR300 142

BR300-8 142

BR350 142

BR350-8 142

BR400 142

BR400-8 142

CBLA038-150 132

CBLA038-30 132

CBLA038-300 132

CBLA050-150 132

CBLA050-30 132

CBLA050-300 132

CBLA075-150 132

CBLA075-30 132

CBLA075-300 132

CBLA100-120 132

CBLA100-30 132

CBLA125-15 132

CBLA125-60 132

CBLA150-15 132

CBLA150-45 132

CBLA200-15 132

CBLA200-30 132

CBLA250-8 132

CBLA250-80 132

CBLA300-50 132

CBLA300-8 132

CBLA350-50 132

CBLA350-8 132

CBLA400-30 132

CBLA400-8 132

CC-ISO-16-G 81

CC-ISO-20-G 81

CC-ISO-25-G 81

CC-ISO-32-G 81

CC-NPT1-B 81

CC-NPT1-G 81

CC-NPT12-B 81

CC-NPT12-G 81

CC-NPT34-B 81

CC-NPT34-G 81

CC-NPT38-B 81

CC-NPT38-G 81

CC-PG11-G 81

CC-PG135-G 81

CC-PG16-G 81

CC-PG21-G 81

CC-PG29-G 81

CC-PG36-G 81

CC-PG7-G 81

CC-PG9-G 81

CCG10-30 149

CCG11-30 149

CCG12-30 149

CCG13-15 149

CCG14-15 149

CCG15-15 149

CC11-38 82

CC11-38P 82

CC135-50 82

CC16-50 82

CC21-75 82

CC29-100 82

CC36-125 82

CC42-150 82

CEA038-30 137

CEA038-300 137

CEA050-30 137

CEA050-300 137

CEA075-150 137

CEA075-30 137

CEA100-120 137

CEA100-30 137

CEA125-15 137

CEA125-60 137

CEA150-15 137

CEA150-45 137

CEA200-15 137

CEA200-30 137

CEA250-8 137

CEA300-8 137

CEA400-8 137

CEA500-8 137

CEA600-8 137

CF-10 150

CF-11 150

CF-12 150

CF-13 150

CF-14 150

CF-140 150

CF-140A 150

CF-15 150

CF-20 150

CF-21 150

CF-22 150

CF-22TB 150

163-E.pdf 1 6/18/2012 2:02:21 PM

Alphanumeric Index

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

164

CF-23 150

CF-24 150

CF-25 150

CF-350 151

CF-516 150

CF-516A 150

CFF-17 151

CFF-27 151

CFF-350A 151

CFM-10 150

CFM-11 150

CFM-12 150

CFM-13 150

CFM-14 150

CFM-15 150

CFM-20 150

CFM-21 150

CFM-22 150

CFM-23 150

CFM-24 150

CFM-25 150

CFM-516 150

CFM-516A 150

CFP-10 150

CFP-11 150

CFP-12 150

CFP-13 150

CFP-14 150

CFP-15 150

CFP-20 150

CFP-21 150

CFP-22 150

CFP-23 150

CFP-24 150

CFP-25 150

CI-1703PL 81

CG11-38 82

CG11-38P 82

CG135-50 82

CG16-50 82

CG21-75 82

CG29-100 82

CG36-125 82

CG42-150 82

CL10-30 148

CL11-30 148

CL12-30 148

CL13-15 148

CL14-15 148

CL140-30 148

CL15-15 148

CL516-30 148

CLFR10-30 149

CLFR11-30 149

CLFR12-30 149

CLFR13-15 149

CLFR14-15 149

CLFR15-15 149

CLFR516-30 149

CLL10-30 148

CLL11-30 148

CLL12-30 148

CLL13-15 148

CLL14-15 148

CLL15-15 148

CLL17-10 148

CLL350-10 148

CLR10-30 149

CLR11-30 149

CLR12-30 149

CLR13-15 149

CLR14-15 149

CLR15-15 149

CLR17-10 149

CLR350-10 149

CSA038-150 133

CSA038-30 133

CSA038-300 133

CSA050-150 133

CSA050-30 133

CSA050-300 133

CSA075-150 133

CSA075-30 133

CSA075-300 133

CSA100-120 133

CSA100-30 133

CSA125-15 133

CSA125-60 133

CSA150-15 133

CSA150-45 133

CSA200-15 133

CSA200-30 133

CSA250-8 133

CSA300-8 133

CSA400-8 133

CXP722 82

CXP723 82

CXP724 82

CXP725 82

CXP726 82

CXP727 82

CTC-10 151

CTC-11 151

CTC-12 151

CTC-13 151

CTC-140 151

CTC-516 151

EF038-150 130

EF038-30 130

EF038-300 130

EF050-150 130

EF050-30 130

EF050-300 130

EF075-150 130

EF075-30 130

EF075-300 130

EF100-120 130

EF100-30 130

EF125-15 130

EF125-75 130

EF150-15 130

EF150-45 130

EF200-15 130

EF200-30 130

EMS038-150 141

EMS038-30 141

EMS050-150 141

EMS050-30 141

EMS075-150 141

EMS075-30 141

EMS100-120 141

EMS100-30 141

EMS125-15 141

EMS125-60 141

EMS150-15 141

EMS150-45 141

EMS200-15 141

EMS200-30 141

EMS250-8 141

EMS300-8 141

EMS400-8 141

EMSP038-150 141

EMSP038-30 141

EMSP050-150 141

EMSP050-30 141

EMSP075-150 141

EMSP075-30 141

EMSP100-120 141

EMSP100-30 141

FTA-U12516 152

FTA-U15516 152

FTA-U1810 152

FTA-U18516 152

FTA-U2310 152

FTA-U2311 152

FTA-U2312 152

FTA-U2411 152

CONFITMRO_EN_ALL.pdf 164 11/28/2011 11:05:50 AM

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

Alphanumeric Index

165

FTA-U2911 152

FTA-U2912 152

FTA-U3411 152

FTA-U3412 152

FTA-U3512 152

GR1W 97

GR2W 97

GR3W 97

GR4W 97

GR5W 97

H050-TB 28

H050BHD 30

H050CAP 31

H050GR-C 29

H050TBF 30

H050TBH 30

H075-TB 28

H075BHD 30

H075CAP 31

H075GR-C 29

H075TBF 30

H075TBH 30

H100-TB 28

H100BHD 30

H100CAP 31

H100GR-C 29

H100TBF 30

H100TBH 30

H125-TB 28

H125BHD 30

H125CAP 31

H125GR-C 29

H125TBF 30

H125TBH 30

H150-075ORGR-TB 31

H150-100ORGR-TB 31

H150-125ORGR-TB 31

H150-TB 28

H150BHD 30

H150CAP 31

H150GR-C 29

H150TBF 30

H150TBH 30

H200-TB 28

H200BHD 30

H200CAP 31

H200GR-C 29

H200TBF 30

H200TBH 30

H250-200ORGR-TB 31

H250-TB 28

H250BHD 30

H250CAP 31

H250GR-C 29

H300-TB 28

H300BHD 30

H300CAP 31

H300GR-C 29

H350-TB 28

H350BHD 30

H350CAP 31

H350GR-C 29

H400-TB 28

H400BHD 30

H400CAP 31

H400GR-C 29

H500-TB 28

H500BHD 30

H500CAP 31

H500GR-C 29

H600-TB 28

H600BHD 30

H600CAP 31

H600GR-C 29

HLT050DATA 78

HLT050 78

HLT075 78

HLT100 78

HLT125 78

HLT150 78

HLT200 78

L050GR-C 29

L075GR-C 29

L100GR-C 29

L125GR-C 29

L150GR-C 29

L200GR-C 29

L250GR-C 29

L300GR-C 29

L350GR-C 29

L400GR-C 29

L500GR-C 29

L600GR-C 29

LA038-150 131

LA038-30 131

LA038-300 131

LA050-150 131

LA050-30 131

LA050-300 131

LA075-150 131

LA075-30 131

LA075-300 131

LA100-120 131

LA100-30 131

LA125-15 131

LA125-60 131

LA150-15 131

LA150-45 131

LA200-15 131

LA200-30 131

LA250-8 131

LA250-80 131

LA300-50 131

LA300-8 131

LA350-50 131

LA350-8 131

LA400-30 131

LA400-8 131

LAS038-150 140

LAS038-30 140

LAS050-150 140

LAS050-30 140

LAS075-150 140

LAS075-30 140

LAS100-120 140

LAS100-30 140

LN501 81

LN502 81

LN503 81

LN-PG11-G 81

LN-PG16-G 81

LN-PG135-G 81

LN-PG21-G 81

LN-PG29-G 81

LN-PG36-G 81

LN-PG7-G 81

LN-PG9-G 81

LN-ISO16-G 81

LN-ISO20-G 81

LN-ISO25-G 81

LN-ISO32-G 81

LNMP038-150 146

LNMP038-300 146

LNMP038-75 146

LNMP050-150 146

LNMP050-300 146

LNMP050-60 146

LNMP075-150 146

LNMP075-50 146

LNMP100-120 146

LNMP100-30 146

LNMP125-30 146

LNMP125-60 146

LNMP150-15 146

LNMP150-45 146

LNMP200-15 146

LNMP200-30 146

LOR038-150 130

CONFITMRO_EN_ALL.pdf 165 11/28/2011 11:05:50 AM

Alphanumeric Index

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

166

LOR038-30 130

LOR038-300 130

LOR050-150 130

LOR050-300 130

LOR050-50 130

LOR075-150 130

LOR075-30 130

LOR075-300 130

LOR100-120 130

LOR100-30 130

LOR125-15 130

LOR125-60 130

LOR150-15 130

LOR200-15 130

LOR250-8 130

LOR300-8 130

LOR350-8 130

LOR400-8 130

LOR500-8 130

LOR600-8 130

LT025-75 129

LT032-75 129

LT038-150 129

LT038-30 129

LT038-300 129

LT050-150 129

LT050-30 129

LT050-300 129

LT075-150 129

LT075-30 129

LT075-300 129

LT100-120 129

LT100-30 129

LT100M 109

LT100P 108

LT125-15 129

LT125-75 129

LT125M 109

LT125P 108

LT150-15 129

LT150-45 129

LT150M 109

LT150P 108

LT200-15 129

LT200-30 129

LT200M 109

LT200P 108

LT250-8 129

LT250-80 129

LT300-50 129

LT300-8 129

LT350-50 129

LT350-8 129

LT38M 109

LT38M-ISO20 110

LT38P 108

LT38P-ISO20 110

LT400-30 129

LT400-8 129

LT4100M 109

LT4100P 108

LT4125M 109

LT4125P 108

LT4150M 109

LT4150P 108

LT4200M 109

LT4200P 108

LT438M 109

LT438M-ISO20 110

LT438P 108

LT450M 109

LT450M-ISO20 110

LT450P 108

LT475M 109

LT475M-ISO25 110

LT475P 108

LT500-8 129

LT50M 109

LT50M-ISO20 110

LT50P 108

LT50P-ISO20 110

LT600-8 129

LT75M 109

LT75M-ISO25 110

LT75P 108

LT75P-ISO25 110

LT9100M 109

LT9100P 108

LT9125M 109

LT9125P 108

LT9150M 109

LT9150P 108

LT9200M 109

LT9200P 108

LT938M 109

LT938M-ISO20 110

LT938P 108

LT938P-ISO20 110

LT950M 109

LT950M-ISO20 110

LT950P 108

LT950P-ISO20 110

LT975M 109

LT975M-ISO25 110

LT975P 108

LTA03810 105

LTA03814 105

LTA05014 105

LTA05016 105

LTA05018 105

LTA07516 105

LTA07518 105

LTA07520 105

LTA10020 105

LTA10024 105

MB-10TB 152

MB-11 152

MB-12 152

MB-13 152

MB-14 152

MB-140 152

MB-15 152

MB-516 152

MSA05014 106

MSA05016 106

MSA05018 106

MSA07516 106

MSA07518 106

MSA07520 106

MSA10020 106

MSA10024 106

MSA10032 106

MSA10036 106

NMC038TB 147

NMC050-1000TB 147

NMC050TB 147

NMC075-500TB 147

NMC075TB 147

NMC100TB 147

NMC125TB 147

NMC150TB 147

NMC200TB 147

NMT038TB 147

NMT050TB 147

NMT075TB 147

NMT100TB 147

NMT125TB 147

NMT150TB 147

NMT200TB 147

PG11-38 82

PG16-50 82

PG21-75 82

PG29-100 82

PG29-125 82

PG36-125 82

PG36-150 82

PSA-M12140 152

PSA-M12516 152

PSA-M130140 152

CONFITMRO_EN_ALL.pdf 166 11/28/2011 11:05:50 AM

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

Alphanumeric Index

167

PSA-M18140 152

PSA-M18516 152

PSA-M30516 152

PSA-M8140 152

SC4-KIT 78

SC65 78

SL038-75 144

SL050-45 144

SL050M-45 144

SL075-30 144

SL100-15 144

SL100M-15 144

SL140-75 144

SL316-75 144

SL340-45 144

SL380-75 144

SL516-75 144

SL716-75 144

SL916-45 144

TCF050-27AL 77

TCF050-40AL 77

TCF050-54AL 77

TCF050-67AL 77

TCF050-78AL 77

TCF075-40AL 77

TCF075-54AL 77

TCF075-67AL 77

TCF075-78AL 77

TCF075-88AL 77

TCF100-100AL 77

TCF100-109AL 77

TCF100-78AL 77

TCF100-88AL 77

TCF125-109AL 77

TCF125-128Al 77

TCF125-147AL 77

TCF150-115AL 77

TCF150-140AL 77

TCF150-165AL 77

TCF200-153AL 77

TCF200-186AL 77

TCF200-219AL 77

TCF250-252AL 77

TCF300-278AL 77

TCF300-304AL 77

TCF300-330AL 77

TR-10-516 151

TR-11-10 151

TR-11-516 151

TR-12-10 151

TR-12-11 151

TR-12-516 151

TR-13-11 151

TR-516-140 151

TRIB-100 18

TRIB-125 18

TRIB-150 18

TRIB-200 18

TRIB-250 18

TRIB-300 18

TRIB-350 18

TRIB-400 18

TRIB-50 18

TRIB-75 18

UG100-15 145

UG120-15 145

UG125-15 145

UG150-15 145

UG200-15 145

UG250-15 145

UG300-15 145

UG340-15 145

UG380-15 145

USL120 144

USL120-75 144

USL380 144

USL380-75 144

USL516 144

USL516-75 144

USL716 144

USL716-75 144

USL916 144

USL916-75 144

VJC038-30 145

VJC050-30 145

VJC050M-30 145

VJC075-30 145

VJC100-30 145

VJC100M-30 145

WMG-LT1 93

WMG-LT10 93

WMG-LT2 93

WMG-LT3 93

WMG-LT4 93

WMG-LT5 93

WMG-LT6 93

WMG-LT7 93

WMG-LT8 93

WMG-LT9 93

WMG-PC1 80

WMG-PC10 80

WMG-PC11 80

WMG-PC12 80

WMG-PC13 80

WMG-PC14 80

WMG-PC15 80

WMG-PC16 80

WMG-PC17 80

WMG-PC18 80

WMG-PC19 80

WMG-PC2 80

WMG-PC20 80

WMG-PC21 80

WMG-PC22 80

WMG-PC3 80

WMG-PC4 80

WMG-PC5 80

WMG-PC6 80

WMG-PC7 80

WMG-PC8 80

WMG-PC9 80

ZHLA038-150 139

ZHLA038-30 139

ZHLA038-300 139

ZHLA050-150 139

ZHLA050-30 139

ZHLA050-300 139

ZHLA075-150 139

ZHLA075-30 139

ZHLA075-300 139

ZHLA100-120 139

ZHLA100-30 139

ZHLA125-15 139

ZHLA125-60 139

ZHLA150-15 139

ZHLA150-45 139

ZHLA200-15 139

ZHLA200-30 139

ZHLA250-8 139

ZHLA300-8 139

ZHLA350-8 139

ZHLA400-8 139

100BP 126

100TB 126

106 11

107 11

108 11

109 11

110-TB 11

111 11

112-TB 11

113-TB 11

114 11

115-TB 11

1210C 42

1211C 42

1212C 42

1213C 42

1214TB 42

CONFITMRO_EN_ALL.pdf 167 11/28/2011 11:05:50 AM

Alphanumeric Index

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

168

1215TB 42

1216TB 42

122 16

1222 16

1223 16

1224 16

1225 16

1226 16

1227 16

1228 16

1229 16

122AL 16

123 16

1230 16

1231 16

1232 16

123AL 16

124 16

1244 39

1245 39

1246 39

1247 39

124AL 16

125-TB 16

1250-TB 39

1251 39

1252 39

1253 39

1254 39

1255 39

1256 39

1257 39

1258 39

125AL 16

126 16

1261 39

1262 39

1263 39

126AL 16

127 16

1275 41

1275AL 41

1275CR 42

1276 41

1276AL 41

1276CR 42

1277 41

1277AL 41

1277CR 42

1278 41

1278AL 41

1278CR 42

1279 41

1279AL 41

1279CR 42

127AL 16

128 16

1280 41

1280AL 41

1280CR 42

1281 41

1281AL 41

1281CR 42

1282 41, 59

1282AL 41

1283 41, 59

1283AL 41

1284 41, 59

1284AL 41

1285 41, 59

1285AL 41

1286 41

1286AL 41

1287 41

1287AL 41

1288 41

1288AL 41

128AL 16

129 16

129AL 16

12GR-TB 97

130-TB 16

130AL 16

131-TB 16

131AL 16

132-TB 16

133-TB 16

133AL 16

134-TB 16

1341 87

1344 87

1345 87

1346 87

1347 87

134AL 16

1350 44, 59

1350AL 44

1350CR 44

1351 44, 59

1351AL 44

1351CR 44

1352 44, 59

1352AL 44

1352CR 44

1353 44, 59

1353AL 44

1353CR 44

1354 44, 59

1354AL 44

1354CR 44

139 11

140 11

141 11

141AL 11

141SL 11

141SST 11

142-TB 11

142AL 11

142SL 11

142SST 11

143 11

143AL 11

143SL 11

143SST 11

144 11

1440 39

1441 39

1442 39

1443 39

144AL 11

144SL 11

144SST 11

145 11

1451 20

1452 20

1453 20

1454 20

1455 20

1456 20

145AL 11

145SL 11

145SST 11

146-TB 11

1460 21

1461 21

1462 21

1463 21

1464 21

1465 21

146AL 11

146SL 11

146SST 11

147 11

147AL 11

147SST 11

1470-TB 21

1471 21

1472 21

1473 21

CONFITMRO_EN_ALL.pdf 168 11/28/2011 11:05:50 AM

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

Alphanumeric Index

169

1474 21

1475 21

1476 21

1477 21

1478 21

1479 21

148 11

148AL 11

148SST 11

149 11

149AL 11

149SST 11

150 11

150AL 11

150SST 11

151 11

151AL 11

151SST 11

152 11

152AL 11

152SST 11

153 11

153AL 11

153SST 11

1942 23

1943 23

1944 23

1945 23

1946 23

1947 23

1948 23

1949 23

1950 23

1951 23

1953 23

1954 23

1GR-TB 97

2111 86

2116 86

2200 68

2201 68

2202 68

2203 68

2204 68

2205 68

2206-TB 68

2207-TB 68

2208-TB 68

2209 68

2210 68

2211 68

2213 68

2214 68

2215 68

2216 68

2217 68

2218 68

2219 68

222-TB 17

2220-TB 68

2221 68

2222 68

2223 68

223-TB 17

2232 86

2233 86

2234 86

2237 86

2238 86

2239 86

224 17

225-TB 17

2250 67

2251 67

2252 67

2253 67

2254 67

2255 67

2256 67

2257 67

2258 67

226 17

2267 67

2268 67

2269 67

227 17

2270 67

2271 67

2272 67

2273 67

2274 67

2275 67

2276 67

2277 67

2278 67

2279 67

228-TB 17

2280 67

2281 67

2282 67

2283 67

2284 67

2285 67

2286 67

229-TB 17

230-TB 17

231 17

232 17

233 17

234 17

2432 86

2433 86

2434 86

2438 86

2439 86

2442 86

2443 86

2446 86

2447 86

2448 86

2449 86

2450 86

2454 86

249 117

2516 66

2517 66

2518 66

2519 66

252 117

2520 66

2520-2 69

2521 66

2522 66

2523 66

2524 66

2525 66

253-TB 117

2530-2 69

2530 66

2531 66

2531-2 69

2531-3 69

2532 66

2534 66

2535 66

2536 66

254-C 117

2540-3 69

2540-4 69

2541-2 69

2541-3 69

2541 66

2542 66

2542-2 69

2544 66

2545 66

2546 66

2547 66

2548 66

CONFITMRO_EN_ALL.pdf 169 11/28/2011 11:05:50 AM

Alphanumeric Index

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

170

2549 66

255 117

2555-2 69

2556 66

2557 66

2558 66

2559 66

256 117

2562 66

2563 66

2564 66

2565 66

257 117

2573 66

2574 66

2575 66

2576 66

2577 66

258 117

2584 66

2585 66

2586 66

2587 66

259 117

2592 66

2593 66

2594 66

2595 66

2596 66

2631 69

2632 69

2633 69

2634 69

2637 69

2638 69

2639 69

2640 69

2641 69

265 117

266-C 117

267 117

2671 63, 79

2672 79

2673 79

2674 79

2675 79

2676 79

2677 79

2678 63, 79

268-C 117

2680 63, 79

2681 79

2682 79

2683 79

2684 79

2685 63, 79

2686 63, 79

2687 63, 79

2688 63, 79

269 117

2690 79

2691 79

2692 79

2693 79

2694 79

2696 63, 79

2699 63, 79

270 117

2702 63, 79

2703 63, 79

2704 63, 79

2705 63

2705TB 79

2706 63, 79

2707 63, 79

2708 63, 79

2709 63, 79

2710 63, 79

272 117

273-TB 117

274 117

275 117

276 117

277 117

279 117

2827 87

2828 87

2829 87

291-C 118

2918SST 73

2919SST 73

2920 70

2920AL 72

2920NM 63, 75

2920S 70

2920SST 73

2921 70

2921AL 72

2921NM 63, 75

2921S 70

2921SST 73

2922 70

2922AL 72

2922NM 63, 75

2922S 70

2922SST 73

2930 70

2930AL 72

2930NM 63, 75

2930S 70

2930SST 73

2931 70

2931AL 72

2931NM 63, 75

2931S 70

2931SST 73

2932 70

2932AL 72

2932NM 63, 75

2932S 70

2932SST 73

2940 70

2940AL 72

2940NM 63, 75

2940S 70

2940SST 73

2941 70

2941AL 72

2941NM 63, 75

2941S 70

2941SST 73

2942 70

2942AL 72

2942NM 63, 75

2942S 70

2942SST 73

300-TBC 115

302-C 115

304 115

306 115

308 115

310 115

3110-C 115

3112 115

3115 115

3117 115

3118 115

3119 115

312 115

3120 115

3121 115

3122 115

3123 115

3124 115

3125 115

3130-C 116

3132 116

3135 116

3137 116

CONFITMRO_EN_ALL.pdf 170 11/28/2011 11:05:50 AM

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

Alphanumeric Index

171

3138 116

3139 116

314 115

3140 116

3141 116

3142 116

3143 116

3144-TB 116

316 115

3201 124

3202 124, 125

321-C 116

3210 19

3211 19

3212 19

3213 19

3214 19

3215 19

323 116

325 116

326-TB 116

327 116

328 116

329 116

330-TB 116

3300 124, 125

3301-C 118

3302 123

3302M-C 123

3303-C 123

3303M 123

3304 123

3304M 123

3305 123

3305M 123

3306 123

3306M 123

3307 123

3307M 123

3308 123

3309 123

331 116

3310 123

3311 123

3312-C 118

3321 99

3322 99

3323 99

3324 99

3325 99

3326 99

3327 99

3328-TB 99

3329 99

3331 99

3341 99

3342 99

3343 99

3344-TB 99

3345 99

3346 99

3347 99

3348-TB 99

3349 99

3350 124, 125

3352 99

3361 99

3362 99

3363 99

3364 99

3365 99

3366 99

3367 99

3368 99

3369 99

3371 99

34GR-TB 97

3650 12

3651 12

3652 12

3653 12

3654 12

3655 12

3656 12

3657 12

3658 12

3659 12

3661 12

3662 12

370 26

370AL 26

3700 40

3701 40

3702 40

3703 40

3704 40

3705-TB 40

3706 40

3707 40

3708 40

3709 40

371 26

371AL 26

3710 40

3711 40

3712 40

3713 40

3714 40

3715-TB 40

3716 40

3717 40

3718 40

372 26

372AL 26

3720-TB 102

3721-TB 102

3722-TB 102

3723 102

3724-TB 102

3725 102

3726 102

373 26

373AL 26

3730-TB 103

3731-TB 103

3732 103

3733-TB 103

3734-TB 103

3735-TB 103

3736 103

374 26

374AL 26

3740 103

3741 103

3742 103

3743-TB 103

3744-TB 103

3745 103

3746-TB 103

375 26

375AL 26

376 26

377 26

378 26

379-TB 26

381-TB 26

382-TB 26

3861 15

3862 15

3863 15

3864 15

3865 15

3866 15

3870-TB 15

3871-TB 15

3872 15

3873 15

3874 15

3875 15

CONFITMRO_EN_ALL.pdf 171 11/28/2011 11:05:50 AM

Alphanumeric Index

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

172

3876 15

3877 15

3878 15

3879 15

3880 15

3881 15

3882 15

3883 15

3884 15

3886 15

3887 15

3889 15

38GR-TB 97

390 119

391 119

392 119

393 119

394 119

3993 15

3994 15

3995 15

3996 15

3998 15

3999 15

4-250TC 78

4-300TC 78

4-350TC 78

4-400TC 78

401 26

402 26

403-TB 26

404-TB 26

405-TB 26

407 26

408 26

409 26

41TB 100

410-TB 26

4159C 59

4160C 59

4161C 59

4162 59

4163 59

4164 59

4176 59

4177 59

4178 59

4179 59

4180 59

4181 59

42TB 100

422 19

423 19

4230 58

4231 58

4232 58

4233 58

4234 58

4235 58

424 19

4240 58

4241-TB 58

4242 58

4243-TB 58

4244 58

4245 58

425 19

4250 37

4251 37

4252 37

4253 37

4254 37

4255 37

426-TB 19

427-TB 19

428-TB 19

429 19

4290 37

4291 37

4292 37

4293 37

4294 37

4295 37

430-TB 20

431 19

433 19

434 19

440-C 45

441 45

442 45

449C 119

460TB 37

461TB 37

462 37

463 37

485 27

486 27

487 27

488 27

489 27

490 27

491 27

492 27

4920 71

4921 71

4922 71

493 27

4932 71

4933 71

494 27

4960 71

4960AL 72

4960NM 63, 75

4961 71

4961AL 72

4961NM 63, 75

4962 71

4962AL 72

4970 71

4970AL 72

4970NM 63, 75

4971 71

4971AL 72

4971NM 63, 75

4972 71

4972AL 72

4972NM 63, 75

4980AL 72

4981AL 72

4982AL 72

503-TB 118

504 118

505-TB 118

5120 57

5121-TB 57

5123 57

5220 57

5221 57

5223 57

5229 92

5231 92

5231AL 92

5231ALGR 96

5231GR 96

5232 92

5232AL 92

5232ALGR 96

5232GR 96

5233 92

5233AL 92

5233ALGR 96

5233GR 96

5234 92

5234AL 92

5234ALGR 96

5234GR 96

5235 92

5235AL 92

5235GR 96

CONFITMRO_EN_ALL.pdf 172 11/28/2011 11:05:50 AM

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

Alphanumeric Index

173

5236 92

5236AL 92

5236GR 96

5237 92

5237AL 92

5237GR 96

5238 92

5238AL 92

5238GR 96

5239 92

5239AL 92

5239GR 96

5240 92

5240AL 92

5240GR 96

5241 92

5241GR 96

5242 92

5242GR 96

5243 92

5243GR 96

5244 92

5244GR 96

5245 92

5245GR 96

5246 92

5246GR 96

5247 92

5247GR 96

5248 92

5248GR 96

5249 92

5249GR 96

5250 92

5250GR 96

5251 93

5251AL 93

5251ALGR 96

5251GR 96

5252 93

5252AL 93

5252ALGR 96

5252GR 96

5253 93

5253AL 93

5253ALGR 96

5253GR 96

5254 93

5254AL 93

5254ALGR 96

5254GR 96

5255 93

5255AL 93

5255GR 96

5256 93

5256AL 93

5256GR 96

5257 93

5257AL 93

5257GR 96

5258 93

5258AL 93

5258GR 96

5259 93

5259GR 96

5260 93

5260GR 96

5261 74-104

5262 74-104

5263 74-104

5264 74-104

5265 74-104

5266 74-104

5267 74-104

5268 104

5269 104

5270 104

5271 94

5271GR 97

5272 94

5272GR 97

5273 94

5273GR 97

5274 94

5274GR 97

5275 94

5275GR 97

5276 94

5276GR 97

5285 92

5285GR 96

5299 104

530-TB 58

5302 12

5303 12

5304 12

5305 12

5306 12

5307 12

5308 12

5309 12

531 58

5311 12

532 58

5320 57

5321 57

5323 57

5330 92

5331 92

5331-HT 91

5331GR 96

5331SST 74

5332 92

5332-HT 91

5332GR 96

5332SST 74

5333 92

5333-HT 91

5333GR 96

5333SST 74

5334 92

5334-HT 91

5334GR 96

5334SST 74

5335 92

5335-HT 91

5335GR 96

5335SST 74

5336 92

5336-HT 91

5336GR 96

5336SST 74

5337 92

5337-HT 91

5337GR 96

5337SST 74

5338 92

5338-HT 91

5338GR 96

5339 92

5339-HT 91

5339GR 96

5340 92

5340-HT 91

5340GR 96

5341 92

5341GR 96

5341-HT 91

5341SST 74

5342 92

5342GR 96

5342-HT 91

5342SST 74

5343 92

5343GR 96

5343-HT 91

5343SST 74

5344 92

5344GR 96

CONFITMRO_EN_ALL.pdf 173 11/28/2011 11:05:50 AM

Alphanumeric Index

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

174

5344-HT 91

5344SST 74

5345 92

5345GR 96

5345-HT 91

5345SST 74

5346 92

5346GR 96

5346-HT 91

5346SST 74

5347 92

5347GR 96

5347-HT 91

5347SST 74

5348 92

5348GR 96

5349 92

5349GR 96

5350 92

5350GR 96

5351 93

5351GR 96

5351-HT 91

5351SST 74

5352 93

5352GR 96

5352-HT 91

5352SST 74

5353 93

5353GR 96

5353-HT 91

5353SST 74

5354 93

5354GR 96

5354-HT 91

5354SST 74

5355 93

5355GR 96

5355-HT 91

5355SST 74

5356 93

5356GR 96

5356-HT 91

5356SST 74

5357 93

5357GR 96

5357-HT 91

5357SST 74

5358 93

5358GR 96

5359 93

5359GR 96

5360 93

5360GR 96

5361 94

5362 94

5363 94

5364 94

5365 94

5366 94

5367 94

5368 94

5369 94

5370 94

5385 92

5385GR 96

5386 92

5386GR 96

5420 57

5421 57

5423 57

5520 57

5521-TB 57

5523 57

5620 57

5621 57

5623 57

5710 103

5711 103

5712 103

5713 103

5714 103

5715 103

5716 103

5717 103

5718 103

586 16

587 16

600-TB 40

600AL-TB 40

601-TB 40

601AL-TB 40

602-TB 40

602AL-TB 40

603-TB 40

603AL-TB 40

604-TB 40

604AL-TB 40

605-TB 40

605AL 40

606-TB 40

606AL 40

607 40

607AL 40

608 40

608AL 40

609 40

609AL 40

610 40

610AL 40

611-TB 40

611AL 40

612 40

612AL 40

613 40

613AL 40

614-TB 40

614AL 40

615-TB 40

615AL 40

6209 126

6210 126

6211 126

6212 126

6214 126

6216 126

6218 126

6302 102

6303 102

6304 102

6305 102

6322 102

6323 102

6324 102

6325 102

65C 119

674 38

675 38

675AL 38

676 38

676AL 38

677 38

677AL 38

678 38

678AL 38

679 38

679AL 38

680-TB 38

680AL 38

681 38

681AL 38

682 38

682AL 38

683 38

683AL 38

684 38

684AL 38

685 38

685AL 38

CONFITMRO_EN_ALL.pdf 174 11/28/2011 11:05:50 AM

Catalogue Page Catalogue Page Catalogue Page

Number Number Number Number Number Number

Alphanumeric Index

175

686 38

686AL 38

687 38

687AL 38

690TB 45

691TB 45

692TB 45

693TB 45

700TB 45

703 45

7330 105

7341 105

7342 105

7343 105

7344-TB 105

7345 105

7346 105

7347 105

7348-TB 105

7351 105

7352 105

7353 105

7354 105

7355 105

7356 105

7357 105

7358 105

7360 105

7361 105

7362 105

7363 105

7364 105

7365 105

7366 105

7367 105

7368 105

8120 33

8121 33

8123 33

8124 36

8125 36

8130 34

8131 34

8132 34

8134 34

815-TB 20

816 20

817 20

818 20

819 20

820 20

821 20

822 20

8220 33

8221 33

8223 33

8224-TB 36

8225 36

823 22

824 20

8320 33

8321 33

8323 33

8324-TB 36

8325 36

841TB 22

8420 33

8421 33

8423 33

8424 36

8425 36

842ALTB 22

842TB 22

843ALTB 22

843TB 22

844 22

844AL 22

845 22

845AL 22

846 22

846AL 22

847 22

847AL 22

848 22

848AL 22

849 22

849AL 22

850 22

850AL 22

851 22

851AL 22

8520 33

8521 33

8523 33

8524 36

8525-TB 36

853 22

853AL 22

854 22

854AL 22

8620 33

8621 33

8623 33

8624 36

8625 36

8720 33

8721 33

8723-TB 33

8724-TB 36

8725-TB 36

8820 33

8821 33

8823-TB 33

8824-TB 36

8825 36

8850 33

8851 33

8853 33

8854 36

8855 36

8970 33

8971 33

8973 33

8974 36

8975 36

9306 106

9330 106

9331 106

9340 106

9341 106

9342 106

9343TB 106

9344 106

9350 106

9351 106

9352TB 106

9353TB 106

9354TB 106

9360 106

9361 106

9362 106

9363 106

9364 106

CONFITMRO_EN_ALL.pdf 175 11/28/2011 11:05:50 AM

176

Notes

CONFITMRO_EN_ALL.pdf 176 11/28/2011 11:05:50 AM

75438_1 ENG 101006 Catalog

Navigation menu

Versions of this User Manual:

Views

Navigation