G BOWERS 107090 Catalog

100022-Catalog 100022-Catalog 100022-Catalog 781720 Batch7 unilog cesco-content

112497-Catalog 112497-Catalog 112497-Catalog 781720 Batch7 unilog cesco-content

103942-Catalog 103942-Catalog 103942-Catalog 781720 Batch7 unilog cesco-content

: Pdf 107090-Catalog 107090-Catalog 781720 Batch6 unilog

Open the PDF directly: View PDF .
Page Count: 72

Download
Open PDF In Browser	View PDF

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G1

NEC Reference . . . . . . . . . . . . . . . . . . . . . . G2-G3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . G4-G5
Outlet Boxes. . . . . . . . . . . . . . . . . . . . . . . . G6-G24
Switch and Handy Boxes . . . . . . . . . . . . . G25-G41
Miscellaneous Products . . . . . . . . . . . . . . G42-G43
Rings & Covers . . . . . . . . . . . . . . . . . . . . G44-G57
Multi-Gang Covers . . . . . . . . . . . . . . . . . . . . . . G58
Nonmetallic Boxes . . . . . . . . . . . . . . . . . . G59-G62
Cross-Reference Charts . . . . . . . . . . . . . . G63-G72

G

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G2

NATIONAL ELECTRICAL CODE® REFERENCE
Article 314 of the National Electrical Code• covers the installation and use of boxes. The Article includes table references that guide the electrician in
the selection of proper size boxes necessary to safely accommodate electrical service requirements. The box capacity table is reproduced in part
from the N.E. Code as a quick reference and guide. The N.E. Code should be consulted for complete details.
314.16 Number of Conductors in Outlet, Device, and Junction Boxes, and Conduit Bodies. Boxes shall be of sufficient size to provide free space
for all conductors enclosed in the box.
The provisions of this section shall not apply to terminal housings supplied with motors. (See Section 430-12.A)
Boxes and conduit bodies containing conductors, size No. 4 or larger, shall also comply with provisions of Section 314.28(A).
(a) Standard Boxes. The maximum number of conductors permitted in standard boxes shall be as listed in Table 314.16(A). See Section 370.28 where
boxes or conduit bodies are used as junction or pull boxes.
Table 314.16(A) Metal Boxes

mm

Bowers ®

Minimum
Volume

Box Trade Size

G

3

in.

Maximum Number of Conductors*
3

cm

in.

18

16

14

12

10

8

6

100 x 32
100 x 38
100 x 54

(4 x 1b)
(4 x 1d)
(4 x 2a)

round/octagonal
round/octagonal
round/octagonal

205
254
353

12.5
15.5
21.5

8
10
14

7
8
12

6
7
10

5
6
9

5
6
8

5
5
7

2
3
4

100 x 32
100 x 38
100 x 54

(4 x 1b)
(4 x 1d)
(4 x 2a)

square
square
square

295
344
497

18.0
21.0
30.3

12
14
20

10
12
17

9
10
15

8
9
13

7
8
12

6
7
10

3
4
6

120 x 32
120 x 38
120 x 54

(4L x 1b)
(4L x 1d)
(4L x 2a)

square
square
square

418
484
689

25.5
29.5
42.0

17
19
28

14
16
24

12
14
21

11
13
18

10
11
16

8
9
14

5
5
8

(3 x 2 x 1d)
(3 x 2 x 2)
(3 x 2 x 2a)
(3 x 2 x 2d)
(3 x 2 x 2f)
(3 x 2 x 3d)

device
device
device
device
device
device

123
164
172
205
230
295

7.5
10.0
10.5
12.5
14.0
18.0

5
6
7
8
9
12

4
5
6
7
8
10

3
5
5
6
7
9

3
4
4
5
6
8

3
4
4
5
5
7

2
3
3
4
4
6

1
2
2
2
2
3

100 x 54 x 38
100 x 54 x 48
100 x 54 x 54

(4 x 2a x 1d)
(4 x 2a x 1g)
(4 x 2a x 2a)

device
device
device

169
213
238

10.3
13.0
14.5

6
8
9

5
7
8

5
6
7

4
5
6

4
5
5

3
4
4

2
2
2

95 x 50 x 65
95 x 50 x 90

(3f x 2 x 2d)
(3f x 2 x 3a)

masonry box/gang
masonry box/gang

230
344

14.0
21.0

9
14

8
12

7
10

6
9

5
8

4
7

2
2

75
75
75
75
75
75

x
x
x
x
x
x

50
50
50
50
50
50

x
x
x
x
x
x

38
50
57
65
70
90

min. 44.5 depth
min. 60.3 depth

FS — single cover/gang (1f)
FD — single cover/gang (2c)

221
295

13.5
18.0

9
12

7
10

6
9

6
8

5
7

4
6

2
3

min. 44.5 depth
min. 60.3 depth

FS — multiple cover/gang (1f)
FD — multiple cover/gang (2c)

295
395

18.0
24.0

12
16

10
13

9
12

8
10

7
9

6
8

3
4

*Where no volume allowances are required by 314.16(B)(2) through 314.16(B)(5).
(1) Table 314.16(A) shall apply where no fittings or devices, such as fixture studs, cable clamps, hickeys, switches, or receptacles, are contained in
the box and where no equipment grounding conductors are part of the wiring within the box. Where one or more of these types of fittings, such as
fixture studs, cable clamps, or hickeys are contained in the box, the number of conductors shown in the table shall be reduced by one for each type
of fitting; an additional deduction of two conductors shall be made for each mounting yoke or strap containing one or more devices or equipment; and
a further deduction of one conductor shall be made for one or more equipment grounding conductors entering the box. Where a second set of
equipment grounding conductors, as permitted by Section 250-74, Exception No. 4, is present in the box, then an additional deduction of one
conductor shall be made. A conductor running through the box shall be counted as one conductor, and each conductor originating outside of the box
and terminating inside the box is counted as one conductor. Conductors, no part of which leaves the box, shall not be counted. The volume of a
wiring enclosure (box) shall be the total volume of the assembled sections, and, where used, the space provided by plaster rings, domed covers,
extension rings, etc., that are marked with their volume in cubic inches, or are made from boxes the dimensions of which are listed in Table 314-16 (a).
Exception: Where an equipment grounding conductor or not over four fixture wires smaller than No. 14, or both, enter a box from a fixture canopy
and terminate within that box, it shall be permitted to omit these conductors from the calculations. Where branch-circuit conductors enter a fixture
canopy and terminate within that canopy, it shall be permitted to count these conductors as not leaving the box.

G2

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G3

(2) For combinations of conductor sizes shown in Table 314-16(a), the maximum number of conductors permitted shall be computed using the
volume per conductor listed in Table 314-16(b), with the deductions provided for in Section 314-16(a)(1). For fixture studs, cable clamps, or hickeys,
these deductions shall be based on the largest conductor entering the box; for each yoke or strap containing one or more devices or equipment, the
deduction shall be based on the largest conductor connected to device(s) or equipment supported by that yoke or strap; and for equipment
grounding conductors, the deductions shall be based on the largest equipment grounding conductor entering the box. The maximum number and
size of conductors listed in Table 314-16(a) shall not be exceeded.
(b) Other Boxes. Boxes 100 cubic inches (1640 cm3) or less other than those described in Table 314-16(a) and nonmetallic boxes shall be durably
and legibly marked by the manufacturer with their cubic inch capacity. The maximum number of conductors permitted shall be computed using the
volume per conductor listed in Table 314-16(b), with the deductions provided for in Section 314-16(a)(1). For fixture studs, cable clamps, or hickeys,
these deductions shall be based on the largest conductor entering the box; for each yoke or strap containing one or more devices or equipment, the
deduction shall be based on the largest conductor connected to device(s) or equipment supported by that yoke or strap; and for equipment
grounding conductors, the deductions shall be based on the largest equipment grounding conductor entering the box. Boxes described in Table 31416(a) that have a larger cubic inch capacity than is designated in the table shall be permitted to have their cubic inch capacity marked as required by
this section, and the maximum number of conductors permitted shall be computed using the volume per conductor listed in Table 314-16(b).

Table 314.16(B) Volume Allowance Required per Conductor
Size of Conductor
(AWG)

Free Space Within Box for Each Conductor
cm3
in.3

18
16
14
12
10
8
6

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

24.6
28.7
32.8
36.9
41.0
49.2
81.9

www.tnb.com

1.50
1.75
2.00
2.25
2.50
3.00
5.00

G3

G
Bowers ®

(c) Conduit Bodies. Conduit Bodies enclosing No. 6 conductors or smaller other than short radius conduit bodies as described in Section 370-5
shall have a cross-sectional area not less than twice the cross-sectional area of the largest conduit or tubing to which it is attached. The maximum
number of conductors permitted shall be the maximum number permitted by Table 1 of Chapter 9 for the conduit to which it is attached.
Conduit bodies shall not contain splices, taps, or devices unless they are durably and legibly marked by the manufacturer with their cubic inch
capacity. The maximum number of conductors permitted shall be computed using the provisions of Section 314-16(b) for other than standard boxes.
Conduit bodies shall be supported in a rigid and secure manner.

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G4

Specifications
Octagonal Outlet Box Brackets

“B” Bracket

“U” Bracket

“H” Bracket

Set d" from the face of box

For use where box need not be
centered between studs.
Positioning spurs included.

Furnished with positioning spurs for
mounting to ceiling joist.

Bowers ®

G Square Outlet Box Brackets

“FB” Flat Bracket

“FBH” Flat Bracket

Position stabilizer provides
3 point support.

With hooks to position box on stud.

“AB” Flat Bracket

“LB” Lateral Bracket

Positioning box off the face of studs.

Locates box flush with the face of the stud.

Switch and Handy Box Brackets

“AB” Angle Bracket

“FB” Flat Bracket

“LB” Lateral Bracket

Positioning box off the face of studs.

Furnished with positioning spur. Set
l" from the face of box.

Furnished with positioning spur. Set
l" from the face of box.

10/32 Tapped hole provided for grounding screw on all boxes.

G4

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G5

Specifications
Cable Clamps

“L” Clamp

“LC” Loom Clamp

“MXN” Clamp

Used with pancake boxes.

For nonmetallic sheathed cable. Leg
holds clamp off the box for easy
cable insertion.

For use with MC (metal clad) and AC (armored)
cable–steel and aluminum #10 to #14 conductors.
Also may be used with nonmetallic sheathed cable
#10 to #14.

Plaster Ears

G
Bowers ®

Plaster ears are included on many switch
boxes. They are set forward h" in the “old
work” position. Two-screw ears are supplied
on shallow boxes and one-screw ears on
52-Loom Boxes.
One-screw ear

Two-screw ear

Industry Standard Specifications

Steel Products
*Underwriters Laboratory Inc. File Number
E-2969 Metallic Outlet Box (QCIT)
E-5476 Outlet Bushings & Fittings (QCRV)
E-19851 Grounding & Bonding Equipment (KDER)
Federal Specifications
A-A5924 (formerly W-J-800)
ANSI/NEMA Standard
OS-1 – 1998
UL LISTED PER STANDARD 514A AND B, METALLIC BOXES AND FITTINGS, GROUNDING AND BONDING EQUIPMENT AND OUTLET BUSHINGS AND FITTINGS.
CONFORM TO UBC (UNIFORM BUILDING CODE) SECTION 4304(f) FOR USE IN FIRE RATED WALLS AND PARTITIONS WITH BOXES HAVING MAXIMUM OF 16
SQUARE INCHES AND NOT MORE THAN 100 SQUARE INCHES OF OPENING FOR ANY 100 SQUARE FEET OF WALL OR PARTITION. OUTLET BOXES ON OPPOSITE
SIDES OF WALL MUST BE SEPARATED BY A HORIZONTAL DISTANCE OF AT LEAST 24 INCHES.

Nonmetallic Products
*Underwriters Laboratory Inc. File Number
E-11461 Nonmetallic Outlet Box (QCMZ)
R-9140 Outlet Boxes and Fittings
Classified for Fire Resistance (CEYY)
ANSI/NEMA Standard
OS-2 – 1998
ICBO Fire Rating Wall & Ceiling
Report #3626 – 2 Hour
UL LISTED PER STANDARD 514C NONMETALLIC OUTLET BOXES, FLUSH DEVICE BOXES AND COVERS, UL CONTROL NO. 271 K UL CLASSIFIED FOR FIRE
RESISTANCE PER STANDARD FIRE TESTS OF BUILDING CONSTRUCTION AND MATERIALS UL 263, UL CONTROL NO. 764 Y. THIS STANDARD IS ALSO KNOWN
AS ANSI AZ 1 ASTM E119 AND NFPA 251 RATED FOR 2 HOURS OR LESS IN FIRE-RESISTANT WALLS CONSISTING OF BEARING OR NON-BEARING WOOD OR
NON-BEARING STEEL STUDS AND GYPSUM. ANY LISTED PLASTIC OR STEEL FACE PLATE MAY BE USED.
*For Underwriters Laboratory Inc., (UL) and Canadian Standards Association (C.S.A.) listing marks, see Bowers products & carton labels.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G5

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G6

Outlet Boxes
Drawn 3" Octagonal Outlet Boxes–11⁄2" Deep
Cat.
No.

Specifications

3-O-1/2

One d" K.O. in each of four sides, with one d"
K.O. in bottom.*

11.8

50

22

3-O-SPL

One d" K.O. in each of two opposite sides, one
f" K.O. in other two sides and one d" K.O.
in bottom.*

11.8

50

22

3-O-LC

For Nonmetallic Sheathed Cable
Two Loom K.O.'s in each of two opposite sides,
two d" K.O.’s in the other two sides and one
d" K.O. in bottom. Two Loom clamps for use on
nonmetallic sheathed cable with 10/32 deep
slotted screws assembled.*

11.8

50

25

3-O-LCE

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides,
two d" K.P.’s in other two sides, and one d" K.O.
in bottom. Two ears, one on each of two opposite
sides. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled.*

11.8

50

26

3-O-B-1/2

One d" K.O. in each of three sides, flat bracket
on fourth side, with one d" K.O. in bottom.
Flat bracket offset d" from face.*

11.8

50

27

3-O-LCB

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket and one d" K.O.
in bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Flat bracket offset d" from face.*

11.8

50

29

3-O-B-MXN

For Metal Clad Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket and one d" K.O.
in bottom. Two MXN clamps for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with 10/32
deep slotted screws. Clamps are UL listed for use
with cable sizes 14/2 through 10/3 with ground. Flat
bracket offset d" from face.*

11.8

50

30

3-O-LCH

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom. Two Loom champs for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Hanger bracket for overhead work.*

11.8

50

31

3-O-1/2

G
Bowers ®

3-O-SPL

3-O-LC

3-O-LCE

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

3-O-B-1/2

3-O-LCB

*Uses Bowers 3" octagonal extension rings and 300 series rings and covers.

3-O-B-MXN

3-O-LCH

G6

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G7

Outlet Boxes
Drawn 3" Octagonal Extension Rings–11⁄2" Deep
Cat.
No.
3-O-EXT-1/2

Specifications

Cu. In.
Capacity
11.8

Extension Ring
1d" Deep – 3d" Octagon
Four d" K.O.’s, one in each of four sides.*

Std. Wt./Lbs.
Pkg. Per Pkg.
50

19

For use with Bowers 3" octagonal outlet boxes and 300 series rings and covers.

3-O-EXT-1/2

Welded 4" Octagonal Outlet Boxes – 11⁄2" Deep
Specifications

4-OW-1/2

One d" K.O. in each of four sides, with five
d" K.O.’s in bottom.*

15.5

50

28

4-OW-3/4

One f" K.O. in each of four sides. Three d" K.O.’s
in a line on the bottom and two f" K.O.’s on opposite
ends in the bottom.*

15.5

50

28

4-OW-SPL

One d" K.O. in each of two opposite sides, one f"
K.O.’s in other two sides. Three d" K.O.’s in a line
on the bottom and two f" K.O.’s on opposite ends
in the bottom.*

15.5

50

28

4-OW-LC

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. on
bottom. Two loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled.*

15.5

50

30

4-OW-LCE

For Nonmetallic Sheathed Cable
15.5
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom. Two ears, one on each of two opposite sides.
Two Loom clamps for use on nonmetallic sheathed
cable with 10/32 deep slotted screws assembled.*

50

34

4-OW-MXN

For Metal Clad Cable
15.5
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom. Two MXN clamps for MC, AC/BX and
nonmetallic sheathed cable (NM) included with 10/32
deep slotted screws. Clamps are UL listed for use
with cable sizes 14/2 through 10/3 with ground.*

50

32

4-OW-1/2

4-OW-3/4

4-OW-SPL

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Uses Bowers 4" octagonal extension rings and 500 series rings and covers.

4-OW-LC

4-OW-LCE

4-OW-MXN

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G7

G
Bowers ®

Cat.
No.

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G8

Outlet Boxes
Welded 4" Octagonal Outlet Boxes–11⁄2" Deep
Cat.
No.

4OW-B-1/2

4-OW-LCB

Bowers ®

G

Specifications
One d" K.O. in each of three sides, bracket on the
other. Five d" K.O.’s in bottom. Knockouts pressed
to inside of box for easy removal. Flat bracket offset
d" from face.*

15.5

50

34

4-OW-LCB

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket, and one d" K.O.
in bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Flat bracket offset d" from face.*

15.5

50

36

4-OW-FB-MXN For Metal Clad Cable
15.5
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket, and one d" K.O.
in bottom. Two MXN clamps for MC, AC/BX and
nonmetallic sheathed cable (NM) included with 10/32
deep slotted screws. Clamps are UL listed for use
with cable sizes 14/2 through 10/3 with ground. Flat
bracket offset d" from face.*

50

35

4-OW-U-1/2

One d" K.O. in each of four sides with five d"
K.O.’s in bottom. “U” bracket for overhead work.*

15.5

50

34

4-OW-ULC

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. “U” bracket for overhead work.*

15.5

50

37

4-OW-U-MXN

For Metal Clad Cable
Two Loom K.O.’s in each of two opposite sides, d"
K.O. in other two sides, and one d" K.O. in bottom.
Two MXN clamps for MC, AC/BX and nonmetallic
sheathed cable (MN) included with 10/32 deep
slotted screws. Clamps are UL listed for use with
cable sizes 14/2 through 10/3 with ground.
“U” bracket for overhead work.*

15.5

50

37

4-OW-LC-BHC For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides. Box mounted with clip to
adjustable hanger. Two Loom clamps for use on
nonmetallic-sheathed cable with 10/32 deep slotted
screws assembled.

15.5

25

22

4-OW-LC-BHS For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides. Box mounted with stud
to adjustable hanger. Two Loom clamps for use on
nonmetallic-sheathed cable with 10/32 deep slotted
screws assembled.*

15.5

25

23

4-OW-U-1/2

4-OW-U-MXN

4-OW-LC-BHC

Std. Wt./Lbs.
Pkg. Per Pkg.

4-OW-B-1/2

4-OW-FB-MXN

4-OW-ULC

Cu. In.
Capacity

**Uses Bowers 4" octagonal extension rings and 500 series rings and covers.

4-OW-LC-BHS

G8

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G9

Outlet Boxes
Welded 4" Octagonal Extension Rings–11⁄2" Deep
Cat.
No.

4-OW-EXT-1/2

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

4-OW-EXT-1/2 Extension Ring
Four d" K.O.’s one in each of four sides.*

15.5

50

21

4-OW-EXT-SPL Extension Ring
One d" K.O. in each of two opposite sides and one
f" K.O. in other two sides.*

15.5

50

21

*Uses Bowers 4" octagonal outlet boxes and 500 series rings and covers.

Drawn 4" Octagonal Outlet Boxes–11⁄2" Deep

4-O-1/2

Cat.
No.

Specifications

4-O-1/2

One d" K.O. in each of four sides, with five d"
K.O.’s in bottom.*

15.5

50

28

G

4-O-3/4

One f" K.O. in each of four sides, with three d"
K.O.’s in a line on the bottom and two f" K.O.’s
on opposite ends in the bottom.*

15.5

50

28

4-O-SPL

One d" K.O. in each of two opposite sides, f"
K.O.’s in other two sides with three d" K.O.’s in a
line on the bottom and two f" K.O.’s on opposite
ends in the bottom.*

15.5

50

28

Bowers ®

4-OW-EXT-SPL

4-O-LC

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled.*

15.5

50

30

4-O-LCB

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket, and one d" K.O.
in bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Flat bracket offset d" from face.*

15.5

50

36

4-O-3/4

4-O-SPL

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Uses Bowers 4" octagonal extension rings and 500 series rings and covers.

4-O-LC

4-O-LCB

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G9

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G10

Outlet Boxes
Drawn 4" Octagonal Outlet Boxes–11⁄2" Deep
Cat.
No.

Specifications

4-O-ULC

Cu. In.
Capacity
15.5

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, d"
K.O.’s in other two sides, and one d" K.O. in bottom.
Two Loom clamps for use on nonmetallic sheathed
cable with 10/32 deep slotted screws assembled.
“U” bracket for overhead work.*

4-O-ULC

Std. Wt./Lbs.
Pkg. Per Pkg.
50

37

*Uses Bowers 4" octagonal extension rings and 500 series rings and covers.

Drawn 4" Octagonal Extension Rings–11⁄2" Deep
Cat.
No.

G

Specifications

Bowers ®

4-O-EXT-SPL Extension Ring
One d" K.O. in each of two opposite sides and one
f" K.O. in other two sides.*

Cu. In.
Capacity
15.5

Std. Wt./Lbs.
Pkg. Per Pkg.
50

21

*Uses Bowers 4" octagonal outlet boxes and 500 series rings and covers.
4-O-EXT-SPL

Drawn 4" Octagonal Outlet Boxes–21⁄8" Deep

4-OD-1/2

4-OD-3/4

Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

4-OD-1/2

One d" K.O. in each of four sides with five d"
K.O.’s in bottom.*

21.5

25

16

4-OD-3/4

One f" K.O. in each of four sides, three d" K.O.’s
in a line on the bottom and two f" K.O.’s on
opposite ends in the bottom.*

21.5

25

16

4-OD-SPL

One d" K.O. in each of two opposite sides, two f"
K.O.’s in other two sides with three d" K.O.’s in a
line on the bottom and two f" K.O.’s on opposite
ends in the bottom.*

21.5

25

16

4-OD-LC

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. other two sides, and one d" K.O. in bottom.
Two Loom clamps for use on nonmetallic sheathed
cable with 10/32 deep slotted screws assembled.*

21.5

25

18

*Uses Bowers 4" octagonal extension rings and 500 series rings and covers.

4-OD-SPL

4-OD-LC

G10

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G11

Outlet Boxes
Drawn 4" Octagonal Outlet Boxes–21⁄8" Deep
Cat.
No.

Std. Wt./Lbs.
Pkg. Per Pkg.
25

21

4-OD-FB-MXN For Metal Clad Cable
21.5
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket, and one d" K.O.
in bottom. Two MXN clamps for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with 10/32
deep slotted screws. Clamps are UL listed for use
with cable sizes 14/2 through 10/3 with ground.
Flat bracket offset d" from face.*

25

21

4-OD-LCB

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket, and one d" K.O.
in bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Flat bracket offset d" from face.*

4-OD-ULC

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. “U” bracket for overhead work.*

21.5

25

21

G

4-U-MXN

For Metal Clad Cable
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom. Two MXN clamps for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with
10/32 deep slotted screws. Clamps are UL listed
for use with cable sizes 14/2 through 10/3 with
ground. “U” bracket for overhead work.*

21.5

25

21

Bowers ®

4-OD-ULC

Cu. In.
Capacity
21.5

4-OD-LCB

4-OD-FB-MXN

Specifications

4-OD-U-MXN

*Uses Bowers 4" octagonal extension rings and 500 series rings and covers.

Drawn 4" Octagonal Extension Rings–21⁄8" Deep
Cat.
No.

Specifications

4-OD-EXT-1/2

Extension Ring
One d" K.O. in each of four sides.*

4-OD-EXT-SPL Extension Ring
One d" K.O. in each of two opposite sides and
one f" K.O. in other two sides.*

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

21.5

25

13

21.5

25

13

*Uses Bowers 4" octagonal outlet boxes and 500 series rings and covers.

4-OD-EXT-1/2

4-OD-EXT-SPL

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G11

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G12

Outlet Boxes
Welded 4" Square Outlet Boxes–11⁄2" Deep
Cat.
No.

Specifications

4-SW-1/2

Three d" K.O.’s in each side and five d" K.O.’s
in bottom.*

21.0

50

37

4-SW-3/4

Two f" K.O.’S in each side. Three d" K.O.’s in a
line in bottom with two f" K.O.’s at opposite ends
in bottom.*

21.0

50

37

4-SW-SPL

Two d" K.O.’s and one f" K.O. in each side.
Three d" K.O.’s in a line in bottom with two f"
K.O.’s at opposite ends in bottom.*

21.0

50

37

4-SW-EKO

One eccentric d" and f" K.O. and two d" K.O.’s
in each side and three d" K.O.’s in a line in bottom
with two eccentric d" and f" K.O.’s at opposite
ends in bottom.*

21.0

50

37

4-SW-LC

For Nonmetallic Sheathed Cable
21.0
Two Loom K.O.’s in each of two opposite sides, three
d" K.O.’s in other two sides and one d" K.O. in
bottom, Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled.*

50

39

4-SW-MXN

For Metal Clad Cable
21.0
Two Loom K.O.’s in each of two opposite sides, three
d" K.O.’s in other two sides, and one d" K.O. in
bottom. Two MXN clamps for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with
10/32 deep slotted screws. Clamps are UL listed for
use with cable sizes 14/2 through 10/3 with ground.*

50

41

4-SW-FB-1/2

Three d" K.O.’s in each of three sides with flat
bracket on fourth side. Five d" K.O.’s in bottom.*

21.0

25

21

4-SW-FB-3/4

Two f" K.O.’s in each of three sides with flat bracket
on fourth side. Three d" K.O.’s in a line in bottom
with two f" K.O.’s at opposite ends in bottom.*

21.0

25

21

4-SW-1/2

4-SW-3/4

Bowers ®

G

4-SW-SPL

4-SW-EKO

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Uses Bowers 4" square extension rings and 400 series rings and covers.
4-SW-LC

4-SW-MXN

4-SW-FB-1/2

4-SW-FB-3/4

G12

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G13

Outlet Boxes
Welded 4" Square Outlet Boxes–11⁄2" Deep
Cat.
No.

4-SW-FB-SPL

Std. Wt./Lbs.
Pkg. Per Pkg.

21.0

25

21

4-SW-FB-EKO

One eccentric d" and f" K.O. and two d"
K.O.’s in each of three sides with flat bracket on
fourth side. Three d" K.O.’s in a line in bottom
with two eccentric d" and f" K.O.’s at opposite
ends in bottom.*

21.0

25

21

4-SW-FBH-1/2

Three d" K.O.’s in three sides with hook bracket
21.0
welded on fourth side and five d" K.O.’s in bottom.
Hook bracket flush with face with hooks set 1/16"
above top of box.*

25

22

4-SW-FBC

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides,
three d" K.O.’s in side opposite flat bracket, and
one d" K.O. in bottom. Two Loom clamps for use
on nonmetallic sheathed cable with 10/32 deep
slotted screws assembled.*

21.0

25

22

4-SW-FB-MXN

For Metal Clad Cable
Two Loom K.O.’s in each of two opposite sides,
three d" K.O.’s in side opposite flat bracket, and
one d" K.O. in bottom. Two MXN clamps for MC,
AC/BX, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screws. Clamps
are UL listed for use with cable sizes 14/2
through 10/3 with ground.*

21.0

25

22

4-SW-LB-1/2

Three d" K.O.’s in each of three sides, lateral
bracket on other side set flush with top of box,
and five d" K.O.’s in bottom.*

21.0

50

42

4-SW-LBC

For Nonmetallic Sheathed Cable
21.0
Two Loom K.O.’s in each of two opposite sides,
three d" K.O.’s in side opposite lateral bracket,
and one d" K.O. in bottom. Lateral bracket set
flush with top of box. Two Loom clamps for use on
nonmetallic sheathed cable with 10/32 deep
slotted screws assembled.*

50

42

4-SW-FB-MXN

*Uses Bowers 4" square extension rings and 400 series rings and covers.

4-SW-LBC

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G13

G
Bowers ®

Two d" K.O.’s and one f" K.O. in each of
three sides with flat bracket on fourth side.
Three d" K.O.’s in a line in bottom with two
f" K.O.’s at opposite ends in bottom.*

4-SW-FBH-1/2

4-SW-LB-1/2

Cu. In.
Capacity

4-SW-FB-SPL

4-SW-FB-EKO

4-SW-FBC

Specifications

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G14

Outlet Boxes
Welded 4" Square Outlet Boxes–11⁄2" Deep
Cat.
No.

Specifications

For Metal Clad Cable
21.0
Two Loom K.O.’s in each of two opposite sides.
Three d" K.O.’s in side opposite lateral bracket,
and one d" K.O. in bottom. Lateral bracket set
flush with top of box. Two MXN clamps for MC,
AC/B, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screws. Clamps
are UL listed for use with cable sizes 14/2 through
10/3 with ground.*

50

45

4-SW-AB-1/2

Three K.O.’s in each of three sides, angle bracket
on other side, and five d" K.O.’s in bottom. Angle
bracket offset l" from top of box.*

21.0

50

45

4-SW-1/2-2BC

Three d" K.O.’s in each side and four d" K.O.’s
in bottom. Mounted with clip on 2-BC bar hanger.
Hanger offset correct depth to set box flush with
ceiling joist.*

21.0

25

31

Bowers ®

G
4-SW-1/2-2BC

Std. Wt./Lbs.
Pkg. Per Pkg.

4-SW-LB-MXN

4-SW-LB-MXN

4-SW-AB-1/2

Cu. In.
Capacity

*Uses Bowers 4" square extension rings and 400 series rings and covers.

Welded 4" Square Extension Rings–11⁄2" Deep

4-SW-EXT-1/2

Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

4-SW-EXT-1/2

Extension Ring
Three d" K.O.’s in each side.*

21.0

50

27

4-SW-EXT-3/4

Extension Ring
Two f" K.O.’s in each side.*

21.0

50

27

4-SW-EXT-SPL

Extension Ring
Two d" K.O.’s and one f" K.O. in each side.*

21.0

50

27

4-SW-EA-SPL

Extension Ring
Two d" K.O.’s and one f" K.O. in each side.
Bottom apertured to gang to any switch or
handy box.*

21.0

50

32

*Uses Bowers 4" square outlet boxes and 400 series rings and covers.
4-SW-EXT-3/4

4-SW-EXT-SPL

4-SW-EA-SPL

G14

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G15

Outlet Boxes
Drawn 4" Square Outlet Boxes–11⁄2" Deep
Cat.
No.

Specifications

4-S-1/2

Three d" K.O.’s in each side and five d"
K.O.’s in bottom.*

21.0

50

37

4-S-3/4

Two f" K.O.’s in each side. Three d" K.O.’s
in a line in bottom with two f" K.O.’s at opposite
ends in bottom.*

21.0

50

37

4-S-SPL

Two d" K.O.’s and one f" K.O. in each side,
and three d" K.O.’s in a line in bottom with two
f" K.O.’s at opposite ends in bottom.*

21.0

50

37

4-S-1/2

4-S-3/4

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Uses Bowers 4" square extension rings and 400 series rings and covers.

G

4-S-EXT-1/2

Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

4-S-EXT-1/2

Extension Ring
Three d" K.O.’s in each side.*

21.0

50

27

4-S-EXT-SPL

Extension Ring
Two d" K.O.’s and one f" K.O. in each side.*

21.0

50

27

*Uses Bowers 4" square outlet boxes and 400 series rings and covers.

4-S-EXT-SPL

Drawn 4" Square Outlet Boxes–11⁄4" Deep
Cat.
No.
4-SS-1/2

Specifications
Three d" K.O.’s in each of two opposite sides,
two d" K.O.’s in other two sides, and five d"
K.O.’s in bottom.*

Cu. In.
Capacity
18.0

Std. Wt./Lbs.
Pkg. Per Pkg.
50

31

*Uses Bowers 4" square extension rings and 400 series rings and covers
4-SS-1/2

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G15

Bowers ®

Drawn 4" Square Extension Rings–11⁄2" Deep

4-S-SPL

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G16

Outlet Boxes
Drawn 4" Square Wall Rings–11⁄2" Deep & 11⁄4" Deep
Cat.
No.

4-S-WR-1/2

Specifications

Std. Wt./Lbs.
Pkg. Per Pkg.

4-S-WR-1/2

Wall Ring
Three d" K.O.’s in each side. Four 8/32 screws
furnished (two in top and two in bottom).*

21.0

50

25

4-S-WR-SPL

Wall Ring
Two d" K.O.’s and one f" K.O. in each side.
Four 8/32 screws furnished (two in top and two
in bottom).*

21.0

50

25

4-SS-WR-1/2

Wall Ring
Three d" K.O.’s in each of two opposite sides,
two d" K.O.’s in other two sides. Four 8/32 screws
furnished (two in top and two in bottom).**

18.0

50

21

4-S-WR-SPL

**For use with two Bowers 403-O rings for back to back devices in 2" partitions.
**For use with two Bowers 403-O rings for back to back devices in 1f" partitions.

G
Bowers ®

Cu. In.
Capacity

Welded 4" Square Outlet Boxes –21⁄8" Deep
4-SS-WR-1/2

Cat.
No.

Specifications

4-SDW-FB-EKO

Std. Wt./Lbs.
Pkg. Per Pkg.

One d" and f" eccentric K.O.’s and two
d" K.O.’s on each side, two d" and f"
eccentrics and 3-d" K.O.’s on the bottom.

30.3

25

24

4-SDW-FB-EKO One d" and f" eccentric K.O.’s and two
d" K.O.’s on three sides, two d" and f"
eccentrics and 3-d" K.O.’s on the bottom
with flat bracket.

30.3

25

24

4-SDW-EKO
4-SDW-EKO

Cu. In.
Capacity

4-SDW-1/2

Three d" K.O.’s in each side and five d"
K.O.’s in bottom.*

30.3

25

24

4-SDW-3/4

Two f" K.O.’s in each side, and three d"
K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom.*

30.3

25

24

4-SDW-SPL

Two d" K.O.’s and one f" K.O. in each side
and three d" K.O.’s in a line in bottom with two
f" K.O.’s at opposite ends in bottom.*

30.3

25

24

4-SDW-1

Two 1" K.O.’s in each side and three d" K.O.’s
in a line in bottom with two f" K.O.’s at opposite
ends in bottom.*

30.3

25

24

4-SDW-1/2

*Uses Bowers 4" square extension rings and 400 series rings and covers.
4-SDW-3/4

4-SDW-SPL

4-SDW-1

G16

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G17

Outlet Boxes
Welded 4" Square Outlet Boxes–21/8" Deep
Cat.
No.

Std. Wt./Lbs.
Pkg. Per Pkg.

30.3

25

24

4-SDW-MXN

For Metal Clad Cable
Two Loom K.O.’s in each of two opposite sides,
three d" K.O.’s in other two sides, and one d"
K.O. in bottom. Two MXN clamps for MC, AC/BX,
and nonmetallic sheathed cable (NM) included
with 10/32 deep slotted screws. Clamps are UL
listed for use with cable sizes 14/2 through 10/3
with ground.*

30.3

25

25

4-SDW-FB-1/2

Three d" K.O.’s in each of three sides, flat bracket
on other side, and five d" K.O.’s in bottom.*

30.3

25

26

4-SDW-FB-3/4

Two f" K.O.’s in each of three sides, flat bracket
on other side, and five d" K.O.’s in bottom.*

30.3

25

26

4-SDW-FB-SPL Two d" K.O.’s and one f" K.O. in each of three
sides, flat bracket on other side, and three d"
K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom.*

30.3

25

26

4-SDW-FBC

30.3

25

26

30.3

25

27

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides,
three d" K.O.’s in side opposite flat bracket, and
one d" K.O. in bottom. Two Loom clamps for use
on nonmetallic sheathed cable with 10/32 deep
slotted screws assembled.*

4-SDW-FB-MXN For Metal Clad Cable
Two Loom K.O.’s in each of two opposite sides,
three d" K.O.’s in side opposite flat bracket, and
one d" K.O. in bottom. Two MXN clamps for MC,
AC/BX, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screws. Clamps
are UL listed for use with cable sizes 14/2 through
10/3 with ground.*
4-SDW-FB-SPL

*Uses Bowers 4" square extension rings and 400 series rings and covers.

4-SDW-FBC

4-SDW-FB-MXN

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G17

G
Bowers ®

For Nonmetallic Sheathed Cable
Two Loom K.O.’s in each of two opposite sides,
three d" K.O.’s in other two sides, and one d"
K.O. in bottom. Two Loom clamps for use on
nonmetallic sheathed cable with 10/32 deep
slotted screws assembled.*

4-SDW-MXN

4-SDW-FB-3/4

Cu. In.
Capacity

4-SDW-LC

4-SDW-LC

4-SDW-FB-1/2

Specifications

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G18

Outlet Boxes
Welded 411⁄16" Square Outlet Boxes–21/8" Deep
Cat.
No.

5-SDW-1/2

Specifications
Three d" K.O.’s in each side, and three d" K.O.’s
in a line in bottom with two f" K.O.’s at opposite
ends in bottom. Four tapped ears.*

42.0

25

29

5-SDW-3/4

Two f" K.O.’s in each of two opposite sides, three
d" K.O.’s in other two sides, and three d" K.O.’s
in a line in bottom with two f" K.O.’s at opposite
ends in bottom. Four tapped ears.*

42.0

25

29

5-SDW-SPL

Two d" K.O.’s and one f" K.O. in each side, three
d" K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom. Four tapped ears.*

42.0

25

29

5-SDW-3/4-1

Two 1" K.O.’s in each of two opposite sides, three
f" K.O.’s in other two sides. Three d" K.O.’s in
a line in bottom and two f" K.O.’s at opposite
ends in bottom. Four tapped ears.*

42.0

25

29

5-SDW-1

Two 1" K.O.’s in each side, and three d" K.O.’s in
a line in bottom with two f" K.O.’s at opposite
ends in bottom. Four tapped ears.*

42.0

25

29

5-SDW-1-1/4

Two 1b" K.O.’s in each of two opposite sides,
two 1" K.O.’s in other two sides, and three d"
K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom. Four tapped ears.*

42.0

25

29

42.0

25

31

42.0

25

31

G
Bowers ®

Std. Wt./Lbs.
Pkg. Per Pkg.

5-SDW-1/2

5-SDW-3/4

5-SDW-SPL

5-SDW-3/4-1

Cu. In.
Capacity

5-SDW-FB-SPL Two d" K.O.’s and one f" K.O. in each of three
sides, flat bracket on other side, and three d"
K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom. Four tapped ears.*
5-SDW-FB-1

Two 1" K.O.’s in each of three sides, flat bracket on
other side, and three d" K.O.’s in a line in bottom
with two f" K.O.’s at opposite ends in bottom.
Four tapped ears.*

*Uses Bowers 4L" square extension rings and 600 series rings and covers.

5-SDW-1

5-SDW-1-1/4

5-SDW-FB-SPL

5-SDW-FB-1

G18

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G19

Outlet Boxes
Welded 411⁄16" Square Extension Rings–21/8" Deep

5-SDW-EXT-1/2

5-SDW-EXT-3/4

Cat.
No.

Specifications

5-SDW-EXT-1/2

Extension Ring
Three d" K.O.’s in each side. Four tapped ears.*

42.0

25

22

5-SDW-EXT-3/4

Extension Ring
Two f" K.O.’s in each side. Four tapped ears.*

42.0

25

22

5-SDW-EXT-SPL Extension Ring
Two d" K.O.’s and one f" K.O. in each side.
Four tapped ears.*

42.0

25

22

5-SDW-EXT-1

42.0

25

22

Extension Ring
Two 1" K.O.’s in each side. Four tapped ears.*

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Uses Bowers 4L" square outlet boxes and 600 series rings and covers.

G
Bowers ®

5-SDW-EXT-SPL

5-SDW-EXT-1

Drawn 411⁄16" Square Outlet Boxes–11/2" Deep
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

5-SS-1/2

Three d" K.O.’s in each of two opposite sides,
two d" K.O.’s in other two sides, and three d"
K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom. Four tapped ears.*

29.5

25

22

5-SS-3/4

Three f" K.O.’s in each of two opposite sides,
two f" K.O.’s in other two sides, and three d"
K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom. Four tapped ears.*

29.5

25

22

5-SS-SPL

Twod" K.O.’s and one f" K.O. in each side,
three d" K.O.’s in a line in bottom with two f"
K.O.’s at opposite ends in bottom. Four tapped
ears.*

29.5

25

22

5-SS-1/2

5-SS-3/4

Specifications

*Uses Bowers 4L" square extension rings and 600 series rings and covers.

5-SS-SPL

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G19

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G20

Outlet Boxes
Drawn 411⁄16" Square Extension Rings–11/2" Deep
Cat.
No.

Specifications

5-SS-EXT-1/2

Cu. In.
Capacity

Extension Ring
Three d" K.O.’s in each of two opposite sides, two
d" K.O.’s in two other sides. Four tapped ears.*

5-SS-EXT-SPL Extension Ring
Two d" K.O.’s and one f" K.O. in each side.
Four tapped ears.*

5-SS-EXT-1/2

Std. Wt./Lbs.
Pkg. Per Pkg.

29.5

25

16

29.5

25

16

*Uses Bowers 4L" square outlet boxes and 600 series rings and covers.
5-SS-EXT-SPL

Welded Thru Boxes

G
Bowers ®

Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

4-D

5" Deep–4" Long–2a" Wide
Two d" K.O.’s and one f" K.O. on both top and
bottom sides, one d" K. O. and one f" K.O. on
side opposite double bracket. Double bracket for
mounting on 4" studding.*

37.5

25

34

4-DW

Dry Wall Thru-Box
4j" Deep–4" Long–2a" Wide
Two d" K.O.’s on both top and bottom sides, one
d" K.O. on side opposite two flat brackets.*

33.0

25

29

4-DWS

3j" Deep–4" Long–2a" Wide
One d" K.O. and one f" K.O. on both top and
bottom sides, and one d" K.O. on side opposite
two flat brackets.*

25.5

25

24

4-D

4-DW

Specifications

*Uses Bowers and 100 series covers.

4-DWS

Multi-Gang Boxes and Partitions
Cat.
No.
702-SPL

702-SPL

Specifications

Cu. In.
Capacity

1m" Deep–4l" Long–6g" Wide
A Two Gang Box
Two d" K.O.’s and two f" K.O.’s in each side,
two d" K.O.’s in each end, and three d" K.O.’s
in a line in bottom with two f" K.O.’s at opposite
ends in bottom. Furnished with four 8/32 screws.*

52.0

Std. Wt./Lbs.
Pkg. Per Pkg.
5

7

*For use with either Bowers 802 and SB-2, 803 and SB-3, or just GB-2 rings and covers.

G20

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G21

Outlet Boxes
Multi-Gang Boxes and Partitions
Cat.
No.
703-SPL
703-SPL

Specifications
A Three Gang Box
1m" Deep–4l" Long–8f" Wide
Three d" K.O.’s and two f" K.O.’s in each side, two
d" K.O.’s in each end, and three d" K.O.’s in a line
in bottom with two f" K.O.’s at opposite ends in
bottom. Furnished with four 8/32 screws.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

65.0

5

8

79.0

5

10

94.3

1

2

110.8

1

2

126.5

1

3

141.3

1

3

155.8

1

4

170.5

1

5

For use with either Bowers 803 and SB-3, 804 and
SB-4, or just GB-3 rings and covers.
704-SPL

704-SPL

A Four Gang Box
1m" Deep–4l" Long–10l" Wide
Four d" K.O.’s and two f" K.O.’s in each side, two
d" K.O.’s in each end, and six d" K.O.’s with four
f" K.O.’s in bottom. Furnished with four 8/32 screws.
For use with either Bowers 804 and SB-4, 805 and
SB-5, or just GB-4 rings and covers.

705-SPL

For use with either Bowers 805 and SB-5, 806 and
SB-6, or just GB-5 rings and covers.
706-SPL

706-SPL

A Six Gang Box
1m" Deep–4l" Long–14a" Wide
Four d" K.O.’s and four f" K.O.’s in each side, two
d" K.O.’s in each end, and six d" K.O.’s with four
f" K.O.’s in bottom. Furnished with four 8/32 screws.
Requires 806. 807, or GB-6 Cover.
For use with either Bowers 806 and SB-6, 807 and
SB-7, or just GB-6 rings and covers.

707-SPL

707-SPL

A Seven Gang Box
1m" Deep–4l" Long–15n" Wide
Five d" K.O.’s and four f" K.O.’s in each side, two
d" K.O.’s in each end, and nine d" K.O.’s with six
f" K.O.’s in bottom. Furnished with four 8/32 screws.
For use with either Bowers 807 and SB-7, 808 and
SB-8, or just GB-7 rings and covers.

708-SPL
708-SPL

An Eight Gang Box
1m" Deep–4l" Long–17f" Wide
Six d" K.O.’s and four f" K.O.’s in each side, two d"
K.O.’s in each end, and nine d" K.O.’s with six f"
K.O.’s in bottom. Furnished with four 8/32 screws.
For use with either Bowers 808 and SB-8, 809 and
SB-9, or just GB-8 rings and covers.

709-SPL

709-SPL

A Nine Gang Box
1m" Deep–4l" Long–19l" Wide
Six d" and five f" K.O.’s in each side and two d"
K.O.’s in each end, and nine d" K.O.’s with six f"
K.O.’s in bottom. Furnished with four 8/32 screws.
For use with either Bowers 809 and SB-9, 810 and
SB-10, or just GB-9 rings and covers.

710-SPL
710-SPL

A Ten Gang Box
1m" Deep–4l" Long–21c" Wide
Six d" K.O.’s and six f" K.O.’s in each side, two d"
K.O.’s in each end and nine d" K.O.’s with six f"
K.O.’s in bottom. Furnished with four 8/32 screws.
For use with either Bowers 810 and SB-10, or just GB-10
rings and covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G
Bowers ®

705-SPL

A Five Gang Box
1m" Deep–4l" Long–12n" Wide
Three d" K.O.’s and four f" K.O.’s in each side, two
d" K.O.’s in each end, and six d" K.O.’s with four
f" K.O.’s in bottom. Furnished with four 8/32 screws.

G21

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G22

Outlet Boxes
Multi-Gang Boxes and Partitions
Cat.
No.
LVP

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

LVP

Multi-Gang Partition
1n" Deep–4l" Wide
A low voltage partition for use in Bowers “700
series” gang boxes when switch rings are used.*

–

25

4

LVPH

Multi-Gang Partition
2d" Deep–4d" Wide
A low voltage partition for use in Bowers “700
series” gang boxes when f" raised switch rings
(Bowers 800 Series) are used.*

–

25

5

LVPH

*For use with Bowers 700 series boxes.

Concrete Boxes

G
Bowers ®

Cat.
No.
900

Std. Wt./Lbs.
Pkg. Per Pkg.

2" Deep–4" Octagon
One d" K.O. in each of four alternating sides and
one f" K.O. in each of the four remaining sides.
Furnished with four 8/32 x d" screws.*

24.3

25

14

901-BW

2d" Deep–4" Octagon
One d" K.O. in each of four alternating sides and
one f" K.O. in each of the four remaining sides.
Furnished with four 8/32 x d" screws.*

30.3

25

1

902

3" Deep–4" Octagon
One d" K.O. in each of four alternating sides and
one f" K.O. in each of the four remaining sides.
Furnished with four 8/32 x d" screws.*

36.8

25

20

903

3d" Deep–4" Octagon
One d" K.O. in each of four alternating sides and
one f" K.O. in each of the four remaining sides.
Furnished with four 8/32 x d" screws.*

42.8

25

24

904

4" Deep–4" Octagon
One d" K.O. in each of four alternating sides and
one f" K.O. in each of the four remaining sides.
Furnished with four 8/32 x d" screws.*

48.8

25

27

905

5" Deep–4" Octagon
One d" K.O. in each of four alternating sides and
one f" K.O. in each of the four remaining sides.
Furnished with four 8/32 x d" screws.*

61.8

25

34

906-BW

6" Deep–4" Octagon
One d" K.O. in each of four alternating sides and
one f" K.O. in each of the four remaining sides.
Furnished with four 8/32 x d" screws.*

73.3

25

42

903

904

Cu. In.
Capacity

900

901-BW

902

Specifications

*For use with Bowers 910 or 911 covers.
905

906-BW

G22

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:42 PM

Page G23

Outlet Boxes
31⁄4" Pancake Boxes
Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

210-L

For Nonmetallic Sheathed Cable
3b" Diameter–d" Deep
Three d" K.O.’s in a line with four Loom K.O.’s at
opposite ends in bottom. Furnished with two
8/32 x d" screws.*

4.0

100

25

210-LC

For Nonmetallic Sheathed Cable
3b" Diameter–d" Deep
Three d" K.O.’s in a line with four Loom K.O.’s at
opposite ends in bottom. One Loom clamp for use
on nonmetallic sheathed cable with 10/32 deep
slotted screw assembled. Furnished with two
8/32 x d" screws in ears.*

4.0

100

29

210-L

210-LC

*Uses Bowers 300 series covers.

G
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

410

4" Diameter–d" Deep
Five d" K.O.’s in bottom. Furnished with two
8/32 x d" screws.*

5.8

50

17

410-L

4" Diameter–d" Deep
Three d" K.O.’s in a line and four Loom K.O.’s at
opposite ends in bottom. Furnished with two
8/32 x d" screws.*

5.8

50

18

410-LC

For Nonmetallic Sheathed Cable
5.8
4" Diameter–d" Deep
Three d" K.O.’s in a line and four Loom K.O.’s at
opposite ends in bottom. Furnished with two Loom
clamps for nonmetallic cable with 10/32 deep slotted
screws and two 8/32 x d" screws in ears.*

50

20

410-L

410-LC

Specifications

*Uses Bowers 500 series covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G23

Bowers ®

4" Pancake Boxes

410

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G24

Outlet Boxes
Fan Support Boxes
Cat.
No.

Specifications

Bowers ®

G
4-O-LCFB (RM)

Std. Wt./Lbs.
Pkg. Per Pkg.

410-LCF (RM)

For Nonmetallic Sheathed Cable
4" Diameter–d" Deep–Ceiling Fan Support
Two d" K.O.’s in bottom. Furnished with necessary
screws for mounting. Includes two 10/32 screws
in ears. Includes NM Loom clamp connector.
Rated for maximum 35 lbs.*

6.0

50

20

4-O-LCF (RM)

For Nonmetallic Sheathed Cable
15.8
1d" Deep–4" Octagon–Ceiling Fan Support
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in other two sides, and one d" K.O. in
bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Box mounting screws supplied.
UL Listed to hold maximum 35 lbs.*

50

42

4-O-LCFB (RM) For Nonmetallic Sheathed Cable
22.0
2a" Deep–4" Octagon–Ceiling Fan Support
Two Loom K.O.’s in each of two opposite sides, one
d" K.O. in side opposite bracket, and one d" K.O.
in bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Bracket offset d" from face. Box
mounting screws supplied. UL Listed to hold
maximum 35 lbs.*

50

63

410-LCF (RM)

4-O-LFC (RM)

Cu. In.
Capacity

*For paddle fan support.

G24

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G25

Switch and Handy Boxes
Gangable Switch Boxes–2" Deep
Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

51

2" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, one d" K.O.
in each end, and two d" K.O.’s in bottom. Two nail
holes in sides. Furnished with plaster ears.*

10.0

50

25

51-NE

2" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, one d" K.O.
in each end, and two d" K.O.’s in bottom. Two nail
holes in sides.*

10.0

50

23

51-LC

For Nonmetallic Cable
2" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, two Loom K.O.’s
in each end, and one d" K.O. in bottom. Furnished
with plaster ears. One Loom clamp for use on
nonmetallic sheathed cable with 10/32 deep slotted
screw assembled. Two nail holes in sides.*

10.0

50

27

51-MXN

For Metal Clad Cable
2" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, two Loom K.O.’s
in each end, one d" K.O. in bottom. Furnished with
plaster ears. One MXN clamp for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with 10/32
deep slotted screw. Clamp is UL listed for use with
cable sizes 14/2 through 10/3 with ground. Two nail
holes in sides.*

10.0

50

28

51-FB

2" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other
side, one d" K.O. in each end, and two d" K.O.’s
in bottom. Bracket offset l" from face.*

10.0

50

28

51

51-NE

51-MXN

Bowers ®

51-LC

G

*Uses Bowers 100 series covers.

Gangable Switch Boxes–21⁄2" Deep
Cat.
No.
51-FB

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

52

2d" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, one d" K.O.
in each end, and two d" K.O.’s in bottom.
Furnished with plaster ears. Four nail holes in sides.*

12.5

50

28

52-3/4-BW

2d" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, one f" K.O.
in each end, and two d" K.O.’s in bottom.
Furnished with plaster ears. Four nail holes in sides.*

12.5

50

30

52

*Uses Bowers 100 series covers.

52-3/4-BW

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G25

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G26

Switch and Handy Boxes
Gangable Switch Boxes–21⁄2" Deep
Cat.
No.

Specifications
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, one d"
K.O. in each end, and two d" K.O.’s in bottom.
Four nail holes in sides.*

12.5

50

27

52-NE-3/4

2d" Deep–3" Long–2" Wide
Two d" K.O.’s in each of two sides, one f" K.O.
in each end, and two d" K.O.’s in bottom.
Four nail holes in sides.*

12.5

50

28

52-LC

For Nonmetallic Cable
12.5
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two loom K.O.’s and
one d" K.O. in each end, and one d" K.O. in
bottom. One Loom clamp for use on nonmetallic
sheathed cable with 10/32 deep slotted screw
assembled. Furnished with plaster ears. Four nail
holes in sides.*

50

31

52-LCNE

For Nonmetallic Cable
12.5
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and
one d" K.O. in each end. One d" K.O. in bottom.
One Loom clamp for use on nonmetallic sheathed
cable with 10/32 deep slotted screw assembled.
Four nail holes in sides.*

50

30

52-MXN

Metal Clad Cable
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and
one d" K.O. in each end, and one d" K.O. in
bottom. Furnished with plaster ears. One MXN
clamp for MC, AC/BX, and nonmetallic sheathed
cable (NM) included with 10/32 deep slotted
screw. Clamp is UL listed for use with cable
sizes 14/2 through 10/3 with ground. Four nail
holes in side.*

12.5

50

31

52-FB

2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other
side, one d" K.O. in each end, and two d"
K.O.’s in bottom. Flat bracket offset l"
from face.*

12.5

50

32

52-FB-3/4

2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other
side, one K.O. in each end, and two f"
K.O.’s in bottom. Flat bracket offset l"
from face.*

12.5

50

32

For Nonmetallic Cable
12.5
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other
side, two Loom K.O.’s and one d" K.O. in each
end, and one d" K.O. in bottom. One Loom clamp
for use on nonmetallic sheathed cable with 10/32
deep slotted screw assembled. Flat bracket offset
l" from face.*

50

35

G
Bowers ®

52-LC

52-LCNE

52-MXN

52-FB

52-FB-3/4

52-FB-W/O-SPUR 2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket without
spur on other side, one d" K.O. in each end,
and two d" K.O.’s in bottom. Flat bracket
offset l" from face.*
52-FB-WO-SPUR

52-FBC

G26

Std. Wt./Lbs.
Pkg. Per Pkg.

52-NE
52.NE

52-NE-3/4

Cu. In.
Capacity

52-FBC

*Uses Bowers 100 series covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G27

Switch and Handy Boxes
Gangable Switch Boxes–21⁄2" Deep
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

For Metal Clad Cable
12.5
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other
side, two Loom K.O.’s and one d" K.O. in each
end, and one d" K.O. in bottom. One MXN clamp
for MC, AC/BX, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screw. Clamp is
UL listed for use with cable sizes 14/2 through 10/3
with ground. Flat bracket offset l" from face.*

50

36

52-LB

2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, lateral bracket on other
side, one d" K.O. in each end, and two d" K.O.’s
in bottom. Lateral bracket offset l" from face.*

12.5

50

32

52-LBC

For Nonmetallic Cable
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, lateral bracket on other
side, two Loom K.O.’s & one d" K.O. in each end,
and one d" K.O. in bottom. One Loom clamp for use
on nonmetallic sheathed cable with 10/32 deep
slotted screw assembled. Flat bracket offset l"
from face.*

12.5

50

39

52-LB-MXN

For Metal Clad Cable
12.5
2d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, lateral bracket on other
side, two Loom K.O.’s and one d" K.O. in each
end, one d" K.O. in bottom. One MXN clamp
for MC, AC/BX, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screw. Clamp is
UL listed for use with cable sizes 14/2 through 10/3
with ground. Flat bracket offset l" from face.*

50

38

52-OW

Old Work Box
2d" Deep–3" Long–2" Wide
One d" K.O. in each end, two d" K.O.’s in bottom,
two d" K.O.’s and one side cleat in each side.
Furnished with plaster ears. Each cleat is actuated
by a 2" full threaded screw used to tighten cleat
snuggly against plaster board.*

12.5

50

31

52-OWC

Old Work Box for Nonmetallic Cable
12.5
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, one
d" K.O. in bottom, two d" K.O.’s and one side
cleat in each side. Furnished with plaster ears. One
Loom clamp for use on nonmetallic sheathed cable
with 10/32 deep slotted screw assembled. Each cleat
is actuated by a 2" full threaded screw used to tighten
cleat snuggly against plaster board.*

50

34

52-OW-MXN

Old Work Box for Metal Clad Cable
12.5
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, one
d" K.O. in bottom, two d" K.O.’s and one side cleat
in each side. Each cleat is actuated by a 2" full
threaded screw used to tighten cleat snuggly against
plaster board. One MXN clamp for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with 10/32
deep slotted screw. Clamp is UL listed for use with
cable sizes 14/2 through 10/3 with ground.*

50

35

52-LB

52-LBC

52-LB-MXN

52-OW

52-OWC

*Uses Bowers 100 series covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G
Bowers ®

52-FB-MXN

52-FB-MXN

52-OW-MXN

Specifications

G27

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G28

Switch and Handy Boxes
Gangable Switch Boxes–23⁄4" Deep
Cat.
No.

Specifications

G

2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, one d" K.O. in each
end, and two d" K.O.’s in bottom. Furnished with
plaster ears. Four nail holes in sides*.

14.0

50

31

53-3/4-BW

2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, one f" K.O. in each
end, and two d" K.O.’s in bottom. Furnished with
plaster ears. Four nail holes in sides.*

14.0

50

31

53-NE

2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, one d" K.O. in each
end, and two d" K.O.’s in bottom. Four nail
holes in sides.*

14.0

50

31

53-NE-3/4

2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, one f" K.O. in each
end, and two d" K.O.’s in bottom. Four nail
holes in sides.*

14.0

50

30

53-LC

For Nonmetallic Cable
2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and
one d" K.O. in each end, and one d" K.O. in
bottom. Furnished with plaster ears. Four nail holes
in sides. One Loom clamp for use on nonmetallic
sheathed cable with 10/32 deep slotted screw
assembled.*

14.0

50

33

53-LCNE

For Nonmetallic Cable
2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and
one d" K.O. in each end, and one d" K.O. in
bottom. One Loom clamp for use on nonmetallic
sheathed cable with 10/32 deep slotted screw
assembled. Four nail holes in sides.*

14.0

50

32

53-MXN

For Metal Clad Cable
2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side. Two Loom K.O.’s and
one d" K.O. in each end, and one d" K.O. in
bottom. One MXN clamp for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with
10/32 deep slotted screw. Clamp is UL listed for
use with cable sizes 14/2 through 10/3 with ground.
Furnished with plaster ears. Four nail holes in sides.*

14.0

50

34

53-FB

2f" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other side,
one d" K.O. in each end, and two d" K.O.’s in
bottom. Flat bracket offset l" from face.*

14.0

50

36

53-FBC

For Nonmetallic Cable
2f" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other side,
two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. Flat offset l" from face.
One Loom clamp for use on nonmetallic sheathed
cable with 10/32 deep slotted screw assembled.*

14.0

50

37

Bowers ®

53-NE

53-NE-3/4

53-LC

53-LCNE

53-MXN

53-FB

Std. Wt./Lbs.
Pkg. Per Pkg.

53
53

53-3/4-BW

Cu. In.
Capacity

*Uses Bowers 100 series covers.
53-FBC

G28

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G29

Switch and Handy Boxes
Gangable Switch Boxes–23⁄4" Deep (Continued)
Cat.
No.

Std. Wt./Lbs.
Pkg. Per Pkg.

For Metal Clad Cable
2f" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket on other side,
two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One MXN clamp for MC,
AC/BX, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screw. Clamp is
U.L listed for use with cable sizes 14/2 through
10/3 with ground.*

14.0

50

38

53-OWEC

For Nonmetallic Cable
2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and
one d" K.O. in each end, and one d" K.O. in
bottom. Furnished with plaster ears. One Loom
clamp for use on nonmetallic sheathed cable with
10/32 deep slotted screw assembled. With old
work swing brackets.*

14.0

50

33

2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, one d" K.O. in each
end, and two d" K.O.’s in bottom. Furnished with
plaster ears. With old work swing brackets.*

14.0

50

31

53-OWE-MXN For Metal Clad Cable
14.0
2f" Deep–3" Long–2" Wide
Two d" K.O.’s in each side. Two Loom K.O.’s and
one d" K.O. in each end, and one d" K.O. in
bottom. One MXN clamp for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with
10/32 deep slotted screw. Clamp is UL listed for
use with cable sizes 14/2 through 10/3 with ground.
Furnished with plaster ears. With old work swing brackets.*

50

34

53-OWEC

G

*Uses Bowers 100 series covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G29

Bowers ®

53-OWE

53-OWE-MXN

Cu. In.
Capacity

53-FB-MXN

53-FB-MXN

53-OWE

Specifications

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G30

Switch and Handy Boxes
Gangable Switch Boxes–31⁄2" Deep
Cat.
No.

Specifications
3d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two d" K.O.’s in each
end, and two d" K.O.’s in bottom. Furnished with
plaster ears. Four nail holes in sides.*

18.0

50

38

54-3/4

3d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two f" K.O.’s in each
end, and two f" K.O.’s in bottom. Furnished with
plaster ears. Four nail holes in sides.*

18.0

50

38

54-NE

3d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two d" K.O.’s in each
end, and two d" K.O.’s in bottom. Four nail holes
in sides.*

18.0

50

36

54-LC

For Nonmetallic Cable
3d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and one
d" K.O. in each end, and one d" K.O. in bottom.
Two Loom clamps for use on nonmetallic sheathed
cable with 10/32 deep slotted screws assembled.
Furnished with plaster ears. Four nails holes in sides.*

18.0

50

40

54-LCNE

For Nonmetallic Cable
3d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and one
d" K.O. in each end, and one d" K.O. in bottom.
Two Loom clamps for use on nonmetallic sheathed
cable with 10/32 deep slotted screws assembled.
Four nails holes in sides.*

18.0

50

40

54-MXN

For Metal Clad Cable
18.0
3d" Deep–3" Long–2" Wide
Two d" K.O.’s in each side, two Loom K.O.’s and one
d" K.O. in each end, and one d" K.O. in bottom.
Furnished with plaster ears. Four nail holes in sides.
Two MXN clamps for MC, AC/BX, and nonmetallic
sheathed cable (NM) included with 10/32 deep slotted
screws. Clamps are UL listed for use with cable sizes
14/2 through 10/3 with ground.*

50

41

54-FBC

For Nonmetallic Cable
3d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket and two d"
K.O.’s in other side, two Loom K.O.’s and one d" K.O.
in each end, and one d" K.O. in bottom. Two Loom
clamps for use on nonmetallic sheathed cable with
10/32 deep slotted screws assembled. Flat bracket
offset l" from face.*

18.0

50

44

54-FB-MXN

For Metal Cable
3d" Deep–3" Long–2" Wide
Two d" K.O.’s in one side, flat bracket and two d"
K.O.’s in other side, two Loom K.O.’s and one d" K.O.
in each end, and one d" K.O. in bottom. Two MXN
clamps for MC, AC/BX, and nonmetallic sheathed
cable (NM) included with 10/32 deep slotted screws.
Clamps are UL listed for use with cable sizes 14/2
through 10/3 with ground. Flat bracket offset l"
from face.*

18.0

50

45

54-3/4

Bowers ®

54-NE

54-LC

54-LCNE

54-MXN

54-FBC

54-FB-MXN

Std. Wt./Lbs.
Pkg. Per Pkg.

54-1/2
54-1/2

G

Cu. In.
Capacity

*Uses Bowers 100 series covers.

G30

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G31

Switch and Handy Boxes
Gangable Switch Boxes Beveled Corners–21⁄4" Deep
Cat.
No.

Cu. In.
Capacity

Specifications

Std. Wt./Lbs.
Pkg. Per Pkg.

230-CC

For Nonmetallic Cable
2b" Deep–3" Long–2" Wide
Two Loom K.O.’s in each end, and one d" K.O. in
bottom. One Loom clamp for use on nonmetallic
sheathed cable with 10/32 deep slotted screw
assembled.*

10.5

50

25

230-LCC

For Nonmetallic Cable
2b" Deep–3" Long–2" Wide
Two Loom K.O.’s in each end, and one d" K.O. in
bottom. One Loom clamp for use on nonmetallic
sheathed cable with 10/32 deep slotted screw
assembled.*

10.5

50

28

230-CC

230-LCC

*Uses Bowers 100 series covers.

G
Welded Non-Gangable Switch Boxes–2 ⁄2" Deep
1

Cat.
No.

72-C

72-ONCS

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

72

2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. Four nail holes included.*

12.5

50

28

72-C

For Nonmetallic Cable
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. Four nail holes included. One
Loom clamp for use on nonmetallic sheathed cable
with 10/32 deep slotted screw assembled.*

12.5

50

30

72-CE

For Nonmetallic Cable
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One Loom clamp for use on
nonmetallic sheathed cable with 10/32 deep slotted
screw assembled. Furnished with ears. Four nail
holes included.*

12.5

50

32

72-OC

For Nonmetallic Cable
12.5
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One Loom clamp for use on
nonmetallic sheathed cable with 10/32 deep slotted
screw assembled. Four nail holes included. Provisions
for external nails included.*

50

33

72-ONCS

For Nonmetallic Cable
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. Furnished with ears. One
Loom clamp for use on nonmetallic sheathed cable
with 10/32 deep slotted screw assembled. Four nail
holes included. Two 16-penny nails swaged at an
angle in box.*

12.5

50

34

72-CE

72-OC

Specifications

*Uses Bowers 100 series covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G31

Bowers ®

72

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G32

Switch and Handy Boxes
Welded Non-Gangable Switch Boxes–21⁄2" Deep (Continued)
Cat.
No.
72-OWE

72-FB-MXN

Bowers ®

72-ONS-MXN

Std. Wt./Lbs.
Pkg. Per Pkg.

2d" Deep–3" Long–2" Wide
12.5
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. With old work swing brackets.*

50

28

12.5

50

34

For Metal Clad Cable
12.5
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, one
d" K.O. in bottom, and flat bracket on one side
offset l" from face. Two MXN clamps for MC,
AC/BX, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screws. Clamps are
UL listed for use with cable sizes 14/2 through
10/3 with ground. Four nail holes included.*

50

34

72-ONS-MXN For Metal Clad Cable
2d" Deep–3" Long–2" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One MXN clamp for MC,
AC/BX, and nonmetallic sheathed cable (NM)
included with 10/32 deep slotted screw. Clamp is
UL listed for use with cable sizes 14/2 through
10/3 with ground. Four nail holes included. Two
16-penny nails swaged at an angle in box.*

72-OWE

G

Cu. In.
Capacity

Specifications

*Uses Bowers 100 series covers.
72-FB-MXN

Welded Non-Gangable Switch Boxes–213⁄16" Deep
Cat.
No.
73-C
73-C

Specifications
For Nonmetallic Cable
2m" Deep–3" Long–2!" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One Loom clamp for use on
nonmetallic sheathed cable with 10/32 deep slotted
screw assembled. Four nail holes included.*

Cu. In.
Capacity

Std.
Pkg.

Wt./Lbs.
Per Pkg.

15.8

50

34

*Uses Bowers 100 series covers.

G32

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G33

Switch and Handy Boxes
Welded Non-Gangable Switch Boxes–213⁄16" Deep (Continued)
Cat.
No.

Specifications

Std. Wt./Lbs.
Pkg. Per Pkg.

73-ONCS

For Nonmetallic Cable
2m" Deep–3" Long–2!" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One Loom clamp for use on
nonmetallic sheathed cable with 10/32 deep slotted
screw assembled. Two 16-penny nails swaged at an
angle in box.*

15.8

50

37

73-FBC

For Nonmetallic Cable
2m" Deep–3" Long–2!" Wide
Two Loom K.O.’s and one d" K.O. in each end, one
d" K.O. in bottom, and flat bracket on one side offset
l" from face. One Loom clamp for use on nonmetallic
sheathed cable with 10/32 deep slotted screw
assembled. Four nail holes included.*

15.8

50

36

15.8

50

37

73-ONCS

73-FBC

*Uses Bowers 100 series covers.

Welded Non-Gangable Switch Boxes–3" Deep
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

74-CE

For Nonmetallic Cable
3a" Deep–3" Long–2b" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One Loom clamp for use on
nonmetallic sheathed cable with 10/32 deep slotted
screw assembled. Furnished with ears. Four nail
holes included.*

18

50

40

74-ONCS

For Nonmetallic Cable
3a" Deep–3" Long–2b" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. One Loom clamp for use on
nonmetallic sheathed cable with 10/32 deep slotted
screw assembled. Two 16-penny nails swaged at an
angle in box.*

18

50

41

74-FBC

For Nonmetallic Cable
3a" Deep–3" Long–2b" Wide
Two Loom K.O.’s and one d" K.O. in each end, one
d" K.O. in bottom and flat bracket on one side offset
l" from face. One Loom clamp for use on nonmetallic
sheathed cable with 10/32 deep slotted screw
assembled. Four nail holes included.*

18

50

42

74-CE

74-ONCS

74-FBC

Specifications

*Uses Bowers 100 series covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G
Bowers ®

73-FB-MXN For Metal Clad Cable
2m" Deep–3" Long–2!" Wide
Two Loom K.O.’s and one d" K.O. in each end, one
d" K.O. in bottom, and flat bracket on one side offset
l" from face. One MXN clamp for MC, AC/BX, and
nonmetallic sheathed cable (NM) included with 10/32
deep slotted screw. Clamp is UL listed for use with
cable sizes 14/2 through 10/3 with ground. Four nail
holes included.*

73-FB-MXN

Cu. In.
Capacity

G33

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G34

Switch and Handy Boxes
Welded Non-Gangable Switch Boxes–313⁄32" Deep
Cat.
No.

Specifications

75-ONCS

For Nonmetallic Cable
3u" Deep–3" Long–2b" Wide
Two Loom K.O.’s and one d" K.O. in each end, and
one d" K.O. in bottom. Two Loom clamps for use on
nonmetallic sheathed cable with 10/32 deep slotted
screws assembled. Four nail holes included. Two
16-penny nails swaged at angle in box.*

75-ONCS

Cu. In.
Capacity
20.0

Std. Wt./Lbs.
Pkg. Per Pkg.
50

45

*Uses Bowers 100 series covers.

Welded Multi-Gangable Switch Boxes–21⁄2" Deep

G

Cat.
No.

Specifications

Bowers ®

Std. Wt./Lbs.
Pkg. Per Pkg.

For Nonmetallic Cable
25.0
A Two Gang Box
2d" Deep–3" Long–4" Wide
A two gang box. Two Loom K.O.’s and two d" K.O.’s
in each end, flat bracket on one side, and one d" K.O.
in bottom. Two Loom clamps for use on nonmetallic
sheathed cable with 10/32 deep slotted screws
assembled. Flat bracket offset l" from face.*

25

25

271-FB-MXN For Metal Clad Cable
25.0
A Two Gang Box
2d" Deep–3" Long–4" Wide
Two Loom K.O.’s and two d" K.O.’s in each end,
25.0
flat bracket on one side, and one d" K.O. in bottom.
Two MX clamps for MC, AC/BX, and nonmetallic
sheathed cable (NM) included with 10/32 deep slotted
screws. Clamps are UL listed for use with cable
sizes 14/2 through 10/3 with ground. Flat bracket
offset l" from face.*

25

25

25

27

271-FBC

271-FBC

271-FB-MXN

Cu. In.
Capacity

*Uses Bowers SB-2 covers.

Welded Handy Boxes–11⁄2" Deep
Cat.
No.

Specifications

Std. Wt./Lbs.
Pkg. Per Pkg.

10.3

50

24

102-W-LB-1/4 1d" Deep–4" Long–2a" Wide
10.3
Three d" K.O.’s in one side, lateral bracket on other
side, one d" K.O. in each end, and three d" K.O.’s
in bottom. Furnished with four mounting holes in bottom.
Bracket offset 1/4" from face.*

50

30

102-W-1/2

102-W-1/2

Cu. In.
Capacity

1d" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side, one d" K.O. in each
end, and three d" K.O.’s in bottom. Four mounting
holes in bottom.*

*Uses Bowers 100 series covers.
102-W-LB-1/4

G34

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G35

Switch and Handy Boxes
Welded Handy Boxes Extension Ring–11⁄2" Deep
Cat.
No.

102-W-EXT-1/2

Specifications

102-W-EXT-1/2 Extension Ring
1d" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side and one d" K.O.
in each end.*

Cu. In.
Capacity
10.3

Std. Wt./Lbs.
Pkg. Per Pkg.
50

20

*Uses Bowers 100 series covers.

Drawn Handy Boxes–11⁄2" Deep
Cat.
No.
102-1/2

1d" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side, one d" K.O. in each
end, and three d" K.O.’s in bottom. Four mounting
holes in bottom.*

Cu. In.
Capacity
10.3

Std. Wt./Lbs.
Pkg. Per Pkg.
50

24

G
Bowers ®

102-1/2

Specifications

*Uses Bowers 100 series covers.

Welded Handy Boxes–17⁄8" Deep
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

103-W-1/2

1g" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side, one d" K.O. in each
end, and three d" K.O.’s in bottom. Four mounting
holes in bottom.*

13.0

50

28

103-W-3/4

1g" Deep–4" Long–2a" Wide
Two f" K.O.’s in each side, one f" K.O. in each
end, and two f" K.O.’s in bottom. Four mounting
holes in bottom.*

13.0

50

28

103-W-FB-1/2

1g" Deep–4" Long–2a" Wide
Three d" K.O.’s in one side, flat bracket on other
side, one d" K.O. in each end, and three d"
K.O.’s in bottom. Bracket offset l" from face.*

13.0

50

32

103-W-AB

1g" Deep–4" Long–2a" Wide
Three d" K.O.’s in one side, angle bracket on other
side, one d" K.O. in each end, and three d"
K.O.’s in bottom. Bracket offset l" from face.*

13.0

50

36

103-W-1/2

103-W-3/4

103-W-FB-1/2

Specifications

*Uses Bowers 100 series covers.

103-W-AB

Welded Handy Boxes Extension Ring–17⁄8" Deep
Cat.
No.

Specifications

103-W-EXT-1/2 Extension Ring
1g" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side and one d" K.O.
in each end.*

Cu. In.
Capacity
10.3

Std. Wt./Lbs.
Pkg. Per Pkg.
50

24

*Uses Bowers 100 series covers.
103-W-EXT-1/2

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G35

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G36

Switch and Handy Boxes
Drawn Handy Boxes–17⁄8" Deep
Cat.
No.

103-1/2-BW

Specifications

Std. Wt./Lbs.
Pkg. Per Pkg.

103-1/2-BW

1g" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side, one d" K.O. in
each end, and three d" K.O.’s in bottom. Four
mounting holes in bottom.*

13.0

50

28

103-3/4

1g" Deep–4" Long–2a" Wide
Two f" K.O.’s in each side, one f" K.O. in each
end, and two f" K.O.’s in bottom. Four mounting
holes in bottom.*

13.0

50

28

103-FB-1/2

1g" Deep–4" Long–2a" Wide
Three d" K.O.’S in each side with flat bracket on
other side, one d" K.O. in each end, and three
d" K.O.’s in bottom. Bracket offset l" from face.*

13.0

50

32

103-3/4

*Uses Bowers 100 series covers.

G
Bowers ®

Cu. In.
Capacity

Welded Handy Boxes–2 1⁄8" Deep

103-FB-1/2

Cat.
No.

Specifications

104-W-FB-1/2

Std. Wt./Lbs.
Pkg. Per Pkg.

104-W-1/2

2a" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side, one d" K.O. in each
end, and three d" K.O.’s in bottom. Four mounting
holes in bottom.*

14.5

50

31

104-W-3/4

2a" Deep–4" Long–2a" Wide
Two f" K.O.’s in each side, one f" K.O. in each
end, and two f" K.O.’s in bottom. Four mounting
holes in bottom.*

14.5

50

31

104-W-FB-1/2 2a" Deep–4" Long–2a" Wide
Three d" K.O.’s in one side, flat bracket on other
side, one d" K.O. in each end, and three d" K.O.’s
in bottom. Flat bracket offset l" from face.*

14.5

50

33

104-W-FB-3/4 2a" Deep–4" Long–2a" Wide
Two f" K.O.’s in one side, flat bracket on other
side, one f" K.O. in each end, and two f" K.O.’s
in bottom. Flat bracket offset l" from face.*

14.5

50

34

104-W-AB

14.5

50

39

104-W-1/2

104-W-3/4

Cu. In.
Capacity

2a" Deep–4" Long–2a" Wide
Three d" K.O.’s in one side, angle bracket on other
side, one d" K.O. in each end, and three d" K.O.’s
in bottom. Bracket offset l" from face.*

*Uses Bowers 100 series covers.

104-W-FB-3/4

104-W-AB

G36

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G37

Switch and Handy Boxes
Drawn Handy Boxes–21⁄8" Deep
Cat.
No.

104-1/2

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

104-1/2

2a" Deep–4" Long–2a" Wide
Three d" K.O.’s in each side, one d" K.O. in each
end, and three d" K.O.’s in bottom.*

14.5

50

31

104-FB-1/2

2a" Deep–4" Long–2a" Wide
Three d" K.O.’s in one side, flat bracket on other
side, one d" K.O. in each end, and three d"
K.O.’s in bottom. Bracket offset l" from face.*

14.5

50

33

*Uses Bowers 100 series covers.
104-FB-1/2

Drawn Handy Boxes–17⁄8" Deep
Cat.
No.
105-1/2

Specifications

15.8

Std. Wt./Lbs.
Pkg. Per Pkg.
50

28

Drawn Handy Boxes–2 3/16" Deep

105-1/2

Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

106-1/2-BW

2i" Deep–4a" Long–2c" Wide
Three d" K.O.’s in each side, one d" K.O. in each
end, and three d" K.O.’s in bottom. Furnished with
two mounting holes in bottom.

18.0

50

33

106-3/4

2i" Deep–4a" Long–2c" Wide
Two f" K.O.’s in each side, one f" K.O. in each
end, and three d" K.O.’s in bottom. Two mounting
holes in bottom.

18.0

50

33

106-FB-1/2

2i" Deep–4a" Long–2c" Wide
Three d" K.O.’s in one side, flat bracket on other
side, one d" K.O. in each end, and three d" K.O.’s
in bottom. Flat bracket offset l" from face.

18.0

50

37

106-FB-3/4

2i" Deep–4a" Long–2c" Wide
Two f" K.O.’s in each side, flat bracket on other
side, one f" K.O. in each end, and three d" K.O.’s
in bottom. Flat bracket offset l" from face.

18.0

50

37

106-1/2-BW

106-3/4

Specifications

106-FB-1/2

106-FB-3/4

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G
Bowers ®

1g" Deep–4" Long–2c" Wide
Three d" K.O.’s in each side, one d" K.O. in each
end, and three d" K.O.’s in bottom. Two mounting
holes in bottom.

Cu. In.
Capacity

G37

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G38

Switch and Handy Boxes
Welded Multi-Gang Handy Boxes–21⁄8" Deep
Cat.
No.

Specifications
A Two Gang Box
2a" Deep–4" Square
Three d" K.O.’s in each of four sides, and three
d" K.O.’s in a line in bottom with two f" K.O.’s at
opposite ends in bottom.*

30.3

25

22

132-W-SPL

A Two Gang Box
2a" Deep–4" Square
Two d" K.O.’s and one f" K.O. in each of four
sides, and three d" K.O.’s in a line in bottom with
two f" K.O.’s at opposite ends in bottom.*

30.3

25

22

132-W-FB-1/2 A Two Gang Box
2a" Deep–4" Square
Three d" K.O.’s in each of three sides, flat bracket
on fourth side, and five d" K.O.’s in bottom. Flat
bracket offset l" from face.*

30.3

25

25

132-W-FB-3/4 A Two Gang Box
2a" Deep–4" Square
Two f" K.O.’s in each of three sides, flat bracket on
fourth side, and three d" K.O.’s in a line with two
f" K.O.’s at opposite ends in bottom. Flat bracket
offset l" from face.*

30.3

25

25

132-W-FB-SPL A Two Gang Box
2a" Deep–4" Square
Two d" K.O.’s and one f" K.O. in each of three
sides, flat bracket on fourth side, and three d"
K.O.’s in a line with two f" K.O.’s at opposite ends
in bottom. Flat bracket offset l" from face.*

30.3

25

25

132-W-AB-1/2 A Two Gang Box
2a" Deep–4" Square
Three d" K.O.’s in each of three sides, angle bracket
on fourth side, and five d" K.O.’s in bottom. Bracket
offset l" from face.*

30.3

25

25

132-W-FBC

30.3

25

26

132-W-SPL

Bowers ®

132-W-FB-1/2

132-W-FB-3/4

132-W-FB-SPL

132-W-AB-1/2

132-W-FBC

G38

Std. Wt./Lbs.
Pkg. Per Pkg.

132-W-1/2

132-W-1/2

G

Cu. In.
Capacity

For Nonmetallic Cable
A Two Gang Box
2a" Deep–4" Square
Two Loom K.O.’s in each of two opposite sides, two
d" K.O.’s in side opposite flat bracket, and one d"
K.O. in bottom. Two Loom clamps for use on
nonmetallic sheathed cable with 10/32 deep slotted
screws assembled. Flat bracket offset l" from face.*

*Uses Bowers SB-2 covers.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G39

Switch and Handy Boxes
Drawn Multi-Gang Handy Boxes–21⁄8" Deep
Cat.
No.
132-SPL

132-SPL

Specifications
A Two Gang Box
2a" Deep–4" Square
Two d" K.O.’s and one f" K.O. in each of four
sides, and three d" K.O.’s in a line in bottom with
two f" K.O.’s at opposite ends in bottom.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

30.3

25

21

44.3

25

28

44.3

20

26

Uses Bowers SB-2 cover.

133-BW

A Three Gang Box
2a" Deep–4" Long–5f" Square
Three d" K.O.’s in each side, two d" K.O.’s in each
end and five d" K.O.’s in bottom.
Uses Bowers SB-3 cover.

133-BW

133-FB-1/2

A Three Gang Box
2a" Deep–4" Long–5f" Square
Three d" K.O.’s in each side, two d" K.O.’s in end
opposite flat bracket and five d" K.O.’s in bottom.
Bracket offset l" from face.

G

Uses Bowers SB-3 cover.

133-FB-1/2

A Three Gang Box
2a" Deep–4" Long–5f" Square
Three d" K.O.’s in each side, two d" K.O.’s in end
opposite lateral bracket, and five d" K.O.’s in
bottom. Bracket offset l" from face.

44.3

20

25

58.0

20

28

58.0

20

30

Uses Bowers SB-3 cover.

134-BW

A Four Gang Box
2a" Deep–4" Long–7d" Square
Four d" K.O.’s in each side, two d" K.O.’s in each
end, and ten d" K.O.’s in bottom.
Uses Bowers SB-4 cover.

133-B

134-B

A Four Gang Box
2a" Deep–4" Long–7d" Square
Four d" K.O.’s in each side, two d" K.O.’s in end
opposite lateral bracket and ten d" K.O.’s in
bottom. Bracket offset l" from face.
Uses Bowers SB-4 cover.

134-BW

134-B

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G39

Bowers ®

133-B

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G40

Switch and Handy Boxes
Shallow Masonry Boxes–21⁄2" Deep & Partitions
Cat.
No.
1-MBS

Specifications
2d" Deep–3f" Long–1g" Wide
A one gang masonry box. Six d" and two f" concentric
K.O.’s. Two in each side and one in each end.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

16.5

10

7

33.0

10

10

49.0

5

7

67.0

5

8

–

50

8

Uses Bowers 100 cover.

1-MBS

2-MBS
2-MBS

2d" Deep–3f" Long–3f" Wide
A one gang masonry box. Eight d" and two f"
concentric K.O.’s. Two in each side and one in each end.
Uses Bowers SB-2 cover.

3-MBS

2d" Deep–3f" Long–5d" Wide
A three gang masonry box. Ten d" and f" concentric
K.O.’s. Three in each side and two in each end.
Uses Bowers SB-3 cover.

3-MBS

4-MBS

G

2d" Deep–3f" Long–7c" Wide
A four gang masonry box. Twelve d" and f" concentric
K.O.’s Four in each side and two in each end.

Bowers ®

Uses Bowers SB-4 cover.
4-MBS

MBPS

Masonry Box Partition
2d" Deep–3f" Wide
A low voltage partition drilled and tapped for mounting.
Furnished with two 8/32 screws.
For use with 2-MBS, 3-MBS, or 4-MBS boxes.

MBPS

Masonry Boxes–31⁄2" Deep & Partitions
Cat.
No.
1-MB

Specifications
3d" Deep–3f" Long–1g" Wide
A one gang masonry box. Eight d" and f" concentric
K.O.’s. Two in each side and two in each end.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

23.3

10

9

46.8

10

12

69.5

5

8

92.0

5

10

–

50

8

Uses Bowers 100 series covers.

1-MB

2-MB

3d" Deep–3f" Long–3f" Wide
A two gang masonry box. Twelve d" and f" concentric
K.O.’s. Four in each of two sides and two in each end.
Uses Bowers SB-2 cover.

3-MB
2-MB

3d" Deep–3f" Long–5d" Wide
A three gang box. Sixteen d" and f" concentric K.O.’s.
Six in each of two sides and two in each end.
Uses Bowers SB-3 cover.

4-MB
3-MB

3d" Deep–3f" Long–7c" Wide
A four gang masonry box. Twelve d" and f" concentric
K.O.’s Eight in each of two sides and two in each end.
Uses Bowers SB-4 cover.

MBP

Masonry Box Partition
3d" Deep–3f" Wide
A low voltage partition drilled and tapped for mounting.
Furnished with two 8/32 screws.
For use with 2-MB, 3-MB, or 4-MB boxes.

4-MB

MBP

G40

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G41

Switch and Handy Boxes
Masonry Thru Boxes
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

MBT-4

Thru Box
3d" Deep–3f" Long–2" Wide
A thru masonry box. Six d" and f" concentric K.O.’s.
Two in each side and one in each end.*

24.0

25

18

MBT-6

Thru Box
5d" Deep–3f" Long–2" Wide
A thru masonry box. Twelve d" and f" concentric
K.O.’s. Four in each side and two in each end.*

38.0

25

30

MBT-8

Thru Box
7d" Deep–3f" Long–2" Wide
A thru masonry box. Eighteen d" and f" concentric
K.O.’s. Six in each side and three in each end.*

52.3

25

41

MBT-4

MBT-6

MBT-8

Specifications

*Uses Bowers 100 series covers.

G
Bowers ®

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G41

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G42

Miscellaneous Products
Bar Hangers
Cat.
No.

2-BC

Bowers ®

44-BD

44-BL

–

50

24

12-BC

20" Long
Straight bar hanger for mounting pancake boxes.
Furnished with clip.

–

50

23

20-BC

22" Long
Shallow offset bar hanger. Offset 1" for mounting 1-d"
deep boxes without rings. Furnished with clips.

–

50

25

44-B

22" Long
–
Deep offset bar hanger. Offset 1-d" for mounting 1-d"
deep boxes with plaster ring to bring cover flush with plaster.
Furnished with stovebolt.

50

23

44-BD

22" Long
Extra deep offset bar hanger. Offset 2-a" for mounting
2-a" deep box. Furnished with stovebolt.

–

50

26

44-BL

26" Long
–
Deep offset bar hanger. Offset 1-d" for mounting 1-d"
deep boxes with plaster ring to bring cover flush with plaster.
Furnished with stovebolt.

50

28

440-B

21" Long
Shallow offset bar hanger. Offset 1" for mounting 1-d" deep
boxes without rings. Furnished with stovebolt.

–

50

21

14-B

20" Long
Straight bar hanger for mounting ceiling boxes. Furnished
with stovebolt.

–

50

18

14-BL

24" Long
Straight bar hanger for mounting ceiling boxes. Furnished
with stovebolt.

–

50

22

BH-S

Adjustable
A bar hanger adjustable for joist spacing from 16" on center
to 24" on center. Minimum adjustment 13-f". Offset 1".
Furnished with stud for box attachment.

–

25

9

BH-C

Adjustable
A bar hanger adjustable for joist spacing from 16" on center
to 24" on center. Minimum adjustment 13-f". Offset 1".
Furnished with clip for box attachment.

–

25

8

440-B

14-B

14-BL

BH-S

BH--C

G42

Std. Wt./Lbs.
Pkg. Per Pkg.

21" Long
Deep offset bar hanger. Offset 1-d" for mounting boxes
with plaster ring. Furnished with clip.

44-B

G

Cu. In.
Capacity

2-BC

12-BC
20-BC

Specifications

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G43

Miscellaneous Products
Plumbers Perforated Tape
Cat.
No.
PT-26
PT-26

Specifications

Cu. In.
Capacity

10' Coils–f" Wide
–
Manufactured from 26 gauge galvanized steel. Made
for 3/16" bolts. Packed 50 coils per carton (500').

Std. Wt./Lbs.
Pkg. Per Pkg.
50

26

Switch Box Supports
Cat.
No.
BH-200
BH-200

Specifications

Cu. In.
Capacity

Dual supports for mounting switch boxes in drywall,
paneling, etc. where there exists no means of
attaching box to stud.

–

Std. Wt./Lbs.
Pkg. Per Pkg.
100

26

100 sets per package. 5 packages per carton.

G

Grounding Devices

GS-SND-SCR

GC-GNO-CLIP

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

12-IPT-7-1/2

Insulated Pigtail
7d" Length
With ground screw and #12 green wire. Prices for
switch and outlet boxes with factory installed
grounding devices available upon request.

–

500

11

GS-GND-SCR

Grounding Screw
–
t" x c"
Green hex head. 100 per box. Prices for switch and
outlet boxes with factory installed grounding devices
available upon request.

1000

5

GC-GNO-CLIP

Grounding Clip
–
To provide grounding of switch and outlet boxes using
nonmetallic sheathed cables #14 and #12 with
grounding wire. 50 per box. Prices for switch and
outlet boxes with factory installed grounding
devices available upon request.

1000

4

Notch Plate
Cat.
No.
NP-3008
NP-3008

Specifications
Notch Plate
h" Thick
To protect nonmetallic cable from nail and
screw penetration.

Cu. In.
Capacity
–

Std. Wt./Lbs.
Pkg. Per Pkg.
500

30

Pipe Nailers

PN-1

Cat.
No.

Specifications

PN-1-1/2
PN-2-3/4
PN-3-1
PN-11-1/2-EMT
PN-12-3/4-EMT
PN-13-1-EMT

d"
f"
1"
d" EMT
f" EMT
1" EMT

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

Cu. In.
Capacity
–
–
–
–
–
–

Std. Wt./Lbs.
Pkg. Per Pkg.
1000
1000
1000
1000
1000
1000

25
29
36
22
24
26

G43

Bowers ®

Cat.
No.

12-IPT-7-1/2

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G44

Rings and Covers
Handy Box Covers

100-BW

Cat.
No.

Specifications

100-BW

a" Raised–4b" Long–2b" Wide
Surface blank. Screws swaged in place*

–

25

4

100-K

a" Raised–4b" Long–2b" Wide
One d" K.O. in center. Screws swaged in place.*

–

25

4

100-DR

a" Raised–4b" Long–2b" Wide
For duplex receptacle. Screw swaged in place.*

–

25

3

100-TS

a" Raised–4b" Long–2b" Wide
For one toggle switch. Screws swaged in place.*

–

25

3

100-SR

a" Raised–4b" Long–2b" Wide
For single receptacle. Opening 1.4" diameter.
Screws swaged in place.*

–

25

3

100-TL

a" Raised–4b" Long–2b" Wide
For four wire twist lock receptacle. Opening 1.594"
diameter. Screws swaged in place.*

–

25

3

100-GFI

a" Raised–4b" Long–2b" Wide
For GFI receptacle. Screws swaged in place.*

–

25

2

100-K

G
Bowers ®

100-DR

100-TS

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Fits any Bowers single gang handy or switch box.

100-SR

100-TL

100-GFI

G44

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G45

Rings and Covers
3" Octagonal Covers
Cat.
No.

Specifications

300-BW

Flat–3d" Diameter
Surface blank.*

–

50

9

300-K

Flat–3d" Diameter
One d" K.O. in center.*

–

50

10

300-DR

Flat–3d" Diameter
For duplex receptacle in center. Screw hole countersunk.*

–

25

3

300-SR

Flat–3d" Diameter
For single receptacle in center. Opening 1.4" in diameter.
Screw holes countersunk.*

–

25

4

300-BW

300-K

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

300-DR

*Fits any Bowers 3" octagonal outlet box or extension ring.

G

300-SR

Bowers ®

4" Square Rings and Covers
Cat.
No.

Specifications

400-BW

Flat–4" Square
Surface blank.*

–

50

15

400-K

Flat–4" Square
One d" K.O. in center.*

–

50

15

401-CS

b" Raised–4" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

1.0

25

6

401-C

d" Raised–4" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

2.8

50

13

401-CA

f" Raised–4" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

4.3

25

8

401-CC

e" Raised–4" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

3.8

25

7

401-CB

1" Raised–4" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

6.3

25

9

400-BW

400-K

401-CS

401-C

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Fits any Bowers 4" square outlet box or extension ring.
401-CA

401-CC

401-CB

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G45

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G46

Rings and Covers
4" Square Rings and Covers (Continued)
Cat.
No.

10

Flat–4" Square
For single switch or receptacle.*

–

25

7

403-B

b" Raised–4" Square
For single switch or receptacle.*

1.8

50

11

403-O

b" Raised–4" Square
Offset for single device at one side. Other side is blank.*

1.0

25

7

403-ST

Steel Tile Ring
1.0
b" Raised–4" Square
For single switch or receptacle. Ears tapped 8/32–2-23/32"
on centers.*

50

11

403-BW

d" Raised–4" Square
For single switch or receptacle.*

4.0

50

13

403-T

Steel Tile Ring
3.5
d" Raised–4" Square
For single switch or receptacle. Ears tapped 8/32–2-23/32"
on centers.*

50

14

403-C

e" Raised–4" Square
For single switch or receptacle.*

3.8

50

14

403-A

f" Raised–4" Square
For single switch or receptacle.*

5.3

25

8

404-F

Flat–4" Square
For two switches or receptacles.*

–

25

3

404-B

b" Raised–4" Square
For two switches or receptacles.*

2.5

50

8

403-F

G
Bowers ®

403-O

403-BW

Std. Wt./Lbs.
Pkg. Per Pkg.
25

1b" Raised–4" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

403-F

403-ST

Cu. In.
Capacity
8.0

401-CD
401-CD

403-B

Specifications

*Fits any Bowers 4" square outlet box or extension ring.

403-T

403-C

403-A

404-F

404-B

G46

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G47

Rings and Covers
4" Square Rings and Covers (Continued)

404-BW

404-C

Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

404-BW

d" Raised–4" Square
For two switches or receptacles.*

5.8

50

11

404-C

e" Raised–4" Square
For two switches or receptacles.*

7.8

25

5

404-A

f" Raised–4" Square
For two switches or receptacles.*

9.3

25

7

405-B

g" Raised–4" Square
For single switch or receptacle.*

5.0

25

8

405-A

1" Raised–4" Square
For single switch or receptacle.*

6.5

25

9

405-BW-R

1b" Raised–4" Square
For single switch or receptacle.*

8.3

25

10

406-A

1" Raised–4" Square
For two switches or receptacles.*

11.8

25

8

406-BW

1b" Raised–4" Square
For two switches or receptacles.*

14.8

25

10

404-A

*Fits any Bowers 4" square outlet box or extension ring.
405-A

405-BW-R

406-A

406-BW

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G47

Bowers ®

405-B

G

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G48

Rings and Covers
4" Square Tile Rings–Steel
Cat.
No.

Specifications

407-A

d" Raised–4" Square
For single switch or receptacle.*

4.0

10

2

407-B

f" Raised–4" Square
For single switch or receptacle.*

5.5

10

2

407-C

1" Raised–4" Square
For single switch or receptacle.*

7.8

10

3

407-D

1b" Raised–4" Square
For single switch or receptacle.*

9.0

10

3

407-F

Steel Tile Ring
d" Raised–4" Square
For single switch or receptacle.*

11.5

10

4

407-G

Steel Tile Ring
2" Raised–4" Square
For single switch or receptacle.*

14.8

10

4

408-A

d" Raised–4" Square
For two switches or receptacles.*

5.8

10

2

408-B

f" Raised–4" Square
For two switches or receptacles.*

9.3

10

2

408-C

1" Raised–4" Square
For two switches or receptacles.*

12.0

10

3

408-D

1b" Raised–4" Square
For two switches or receptacles.*

14.8

10

3

408-F

Steel Tile Ring
1d" Raised–4" Square
For two switches or receptacles.*

17.5

10

3

408-G

Steel Tile Ring
2" Raised–4" Square
For two switches or receptacles.*

23.0

10

4

407-A

407-B

407-C

Bowers ®

G
407-D

407-F

407-G

408-A

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Fits any Bowers 4" square outlet box or extension ring.

408-B

408-C

408-D

408-F

408-G

G48

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G49

Rings and Covers
4" Square Industrial Device Covers
Cat.
No.

451-NEC

d" Raised–4" Square
Surface blank. Each cover individually packaged with
the necessary screws for mounting.*

6.5

25

11

450

d" Raised–4" Square
For one toggle switch and one single receptacle.
Opening 1.4" diameter. Each cover individually packaged
with the necessary screws for mounting.*

6.5

25

9

451-NEC d" Raised–4" Square
For one toggle switch and one duplex receptacle. Each
cover individually packaged with the necessary screws
for mounting.*

6.5

25

10

452-NEC d" Raised–4" Square
For two duplex receptacles. Each cover individually
packaged with the necessary mounting screws.*

6.5

25

9

453-NEC d" Raised–4" Square
6.5
For one duplex receptacle in center. Each cover individually
packaged with the necessary mounting screws.*

25

10

454

d" Raised–4" Square
6.5
For one single receptacle in center. Opening 1.4" diameter.
Each cover individually packaged with the necessary
mounting screws.*

25

10

455

d" Raised–4" Square
For two single receptacles. Openings 1.4" diameter. Each
cover individually packaged with the necessary mounting
screws.*

6.5

25

10

456

d" Raised–4" Square
6.5
For two toggle switches. Each cover individually packaged
with the necessary mounting screws.*

25

11

6.5

25

9

453-NEC

454

457-NEC d" Raised–4" Square
For one duplex and one single receptacle. Opening 1.4"
diameter. Each cover individually packaged with the
necessary mounting screws.*

455

456

457-NEC

458

Std. Wt./Lbs.
Pkg. Per Pkg.

G

458

d" Raised–4" Square
For one four wire twist lock receptacle in center. Opening
1.594" diameter. Each cover individually packaged with
the necessary mounting screws.*

6.5

25

10

459

d" Raised–4" Square
6.5
Opening to accommodate one Bryant 9303, Hubbell 9350,
Arrow 9344, or P & S 3853 receptacle in center. Opening
2.138" diameter. Each cover individually packaged with
the necessary mounting screws.*

25

9

460-BW

d" Raised–4" Square
For one toggle switch in center. Each cover individually
packaged with the necessary mounting screws.*

25

11

6.5

*Fits any Bowers 4" square outlet box or extension ring.

459

460-BW

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G49

Bowers ®

452-NEC

Cu. In.
Capacity

449-BW
449-BW

450

Specifications

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G50

Rings and Covers
4" Square Industrial Device Covers (Continued)
Cat.
No.

25

11

465

d" Raised–4" Square
Opening to accommodate Hubbell 3330 receptacle in
center. Opening 1.740" diameter. Each cover individually
packaged with the necessary mounting screws.*

6.5

25

10

469

a" Raised–4" Square
Surface blank. Each cover individually packaged with the
necessary mounting screws.*

–

25

6

470-BW

a" Raised–4" Square
For one toggle switch and one single receptacle. Opening
1.4" diameter. Each cover individually packaged with the
necessary mounting screws.*

–

25

5

471-NEC

a" Raised–4" Square
For one toggle switch and one duplex receptacle. Each
cover individually packaged with the necessary mounting
screws.*

–

25

5

472-NEC

a" Raised–4" Square
For two duplex receptacles. Each cover individually
packaged with the necessary mounting screws.*

–

25

4

473-NEC

a" Raised–4" Square
–
For one duplex receptacle in center. Each cover individually
packaged with the necessary mounting screws.*

25

5

474-BW

a" Raised–4" Square
–
For one single receptacle in center. Opening 1.4" diameter.
Each cover individually packaged with the necessary
mounting screws.*

25

6

475

a" Raised–4" Square
For two single receptacles. Openings 1.4" diameter. Each
cover individually packaged with the necessary mounting
screws.*

–

25

6

476

a" Raised–4" Square
–
For two toggle switches. Each cover individually packaged
with the necessary mounting screws.*

25

6

477-NEC

a" Raised–4" Square
For one duplex and one single receptacle. Opening 1.4"
diameter. Each cover individually packaged with the
necessary mounting screws.*

–

25

5

478

a" Raised–4" Square
For one four-wire twist lock receptacle in center. Opening
1.594" diameter. Each cover individually packaged with
the necessary mounting screws.*

–

25

5

469

Bowers ®

471-NEC

472-NEC

473-NEC

474-BW

475

476

Std. Wt./Lbs.
Pkg. Per Pkg.

d" Raised–4" Square
6.5
Opening to accommodate one Bryant 7301, Hubbell 7301,
or Arrow 4515 receptacle in center. Opening 2.45" diameter.
Each cover individually packaged with the necessary
mounting screws.*

465

470-BW

Cu. In.
Capacity

464
464

G

Specifications

*Fits any Bowers 4" square outlet box or extension ring.

477-NEC

478

G50

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G51

Rings and Covers
4" Square Industrial Device Covers (Continued)
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

479-GFI

a" Raised–4" Square
For one GFI receptacle in center. Each cover individually
packaged with the necessary mounting screws.*

–

25

3

480-BW

a" Raised–4" Square
For one toggle switch in center. Each cover individually
packaged with the necessary mounting screws.*

–

25

6

481-BW

a" Raised–4" Square
–
For one GFI receptacle and one toggle switch. Each cover
individually packaged with the necessary mounting screws.*

25

2

482-NEC

a" Raised–4" Square
–
For one GFI and one duplex receptacle. Each cover
individually packaged with the necessary mounting screws.*

25

2

479-GFI

480-BW

Specifications

481-BW

G

*Fits any Bowers 4" square outlet box or extension ring.

4" Octagonal Rings and Covers
Cat.
No.

500-BW-C

Std. Wt./Lbs.
Pkg. Per Pkg.

–

50

13

500-DR

Flat–4" Octagonal
For duplex receptacle. Screw hole countersunk.*

–

50

11

500-K

Flat–4" Octagonal
One d" K.O. in center.*

–

50

13

500-K-3/4 Flat–4" Octagonal
One f" K.O. in center.*

–

50

13

500-SR

Flat–4" Octagonal
For single receptacle in center. Screw holes countersunk.
Opening 1.4" diameter.*

–

25

6

500-TL

Flat–4" Octagonal
Four-wire twistlock in center. Screw holes countersunk.
Opening 1.594" diameter.*

–

25

5

501-C-BW d" Raised–4" Diameter
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

3.0

50

10

e" Raised–4" Diameter
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

4.0

25

6

500-K

501-CC

500-SR

Cu. In.
Capacity

500-BW-C Flat–4" Octagonal
Surface blank.*

500-DR

500-K-3/4

Specifications

*Fits any Bowers 4" octagonal outlet box or extension ring.

500-TL

501-C-BW

501-CC

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G51

Bowers ®

482-NEC

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G52

Rings and Covers
4" Octagonal Rings and Covers (Continued)
Cat.
No.

Bowers ®

501-CS

Std. Wt./Lbs.
Pkg. Per Pkg.

f" Raised–4" Diameter
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

4.5

25

8

501-CB

1" Raised–4" Diameter
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

5.8

25

8

501-CD

1b" Raised–4" Diameter
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

8.3

25

9

501-CS

b" Raised–4" Diameter
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

1.5

25

5

503-BW

d" Raised–4" Diameter
For single switch or receptacle.*

2.5

25

6

501-CD

G

Cu. In.
Capacity

501-CA
501-CA

501-CB

Specifications

*Fits any Bowers 4" octagonal outlet box or extension ring.

4 11⁄16" Square Rings and Covers
503-BW

Cat.
No.

Specifications

600-BW

Flat–4L" Square
Surface blank.*

–

25

11

600-K

Flat–4L" Square
One d" K.O. in center.*

–

25

11

601-C

d" Raised–4L" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

3.0

25

9

601-CC

e" Raised–4L" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

3.5

25

12

601-CA

f" Raised–4L" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

5.0

25

10

601-CB

1" Raised–4L" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

6.8

25

12

601-CD

1b" Raised–4L" Square
Open plaster ring with ears. Ears tapped 8/32–2-23/32"
on centers. Special screw lock feature in slots.*

8.8

25

12

600-BW

600-K

601-C

601-CC

601-CA

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Fits any Bowers 4L" square outlet box or extension ring.

601-CB

601-CD

G52

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G53

Rings and Covers
4 11⁄16" Square Rings and Covers (Continued)
Specifications

603-B

b" Raised–4L" Square
For single switch or receptacle.*

2.0

25

8

603-A

d" Raised–4L" Square
For single switch or receptacle.*

3.3

25

9

603-C

e" Raised–4L" Square
For single switch or receptacle.*

4.5

25

10

603-BW

f" Raised–4L" Square
For single switch or receptacle.*

5.0

25

10

604-F

Flat–4L" Square
For two switches or receptacles.*

–

25

5

604-B

b" Raised–4L" Square
For two switches or receptacles.*

2.8

25

6

604-A

d" Raised–4L" Square
For two switches or receptacles.*

5.5

25

10

604-C

e" Raised–4L" Square
For two switches or receptacles.*

6.8

25

8

604-BW

f" Raised–4L" Square
For two switches or receptacles.*

8.5

25

9

605-BW

1" Raised–4L" Square
For single switch or receptacle.*

6.3

10

5

605-A

1b" Raised–4L" Square
For single switch or receptacle.*

8.0

10

5

606-BW

1" Raised–4L" Square
For two switches or receptacles.*

11.3

10

4

606-A

1b" Raised–4L" Square
For two switches or receptacles.*

13.5

10

5

603-B

603-A

603-C

603-BW

604-F

604-B

604-A

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Fits any Bowers 4L" square outlet box or extension ring.
604-C

604-BW

605-BW

605-A

606-BW

606-A

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G53

G
Bowers ®

Cat.
No.

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G54

Rings and Covers
4 11⁄16" Square Tile Rings

607-A

607-B

607-C

G

Cat.
No.

Specifications

607-A

d" Raised–4L" Square
For single switch or receptacle.*

3.8

10

2

607-B

f" Raised–4L" Square
For single switch or receptacle.*

5.8

10

3

607-C

1" Raised–4L" Square
For single switch or receptacle.*

6.8

10

3

607-D

1b" Raised–4L" Square
For single switch or receptacle.*

9.5

10

3

607-F

1d" Raised–4L" Square
For single switch or receptacle.*

11.3

10

3

607-G

2" Raised–4L" Square
For single switch or receptacle.*

15.0

10

4

608-C

2" Raised–4L" Square
For two switches or receptacles.*

12.5

10

3

608-F

1d" Raised–4L" Square
For two switches or receptacles.*

18.8

10

4

608-G

2" Raised–4L" Square
For two switches or receptacles.*

24.5

10

4

Bowers ®

607-D

607-F

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

*Fits any Bowers 4L" square outlet box or extension ring.

607-G

608-C

608-F

608-G

G54

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G55

Rings and Covers
4 11⁄16" Square Industrial Device Covers
Cat.
No.

651-NEC

7.5

10

6

650-BW

d" Raised–4L" Square
For one toggle switch and one single receptacle.
Opening 1.4" diameter. Each cover individually
packaged with the necessary screws for mounting.*

7.5

10

6

651-NEC

d" Raised–4L" Square
For one toggle switch and one duplex receptacle.
Each cover individually packaged with the necessary
screws for mounting.*

7.5

10

5

652-NEC

d" Raised–4L" Square
For two duplex receptacles. Each cover individually
packaged with the necessary screws for mounting.*

7.5

10

5

653-NEC

d" Raised–4L" Square
For one duplex receptacle in center. Each cover
individually packaged with the necessary screws
for mounting.*

7.5

10

5

654

d" Raised–4L" Square
For one single receptacle in center. Opening 1.4"
diameter. Each cover individually packaged with the
necessary screws for mounting.*

7.5

10

6

655

d" Raised–4L" Square
For two single receptacles. Opening 1.4" diameter. Each
cover individually packaged with the necessary screws
for mounting.*

7.5

10

5

656

d" Raised–4L" Square
For two toggle switches. Each cover individually
packaged with the necessary screws for mounting.*

7.5

10

6

657-NEC

d" Raised–4L" Square
For one duplex and one single receptacle. Opening
1.4" diameter. Each cover individually packaged with the
necessary screws for mounting.*

7.5

10

5

658

d" Raised–4L" Square
For one four-wire twist lock receptacle in center.
Opening 1.594" diameter. Each cover individually
packaged with the necessary screws for mounting.*

7.5

10

6

659

d" Raised–4L" Square
7.5
Opening to accommodate one Bryant 9303, Hubbell 9350,
Arrow 9344, or P & S 3853 receptacle in center. Opening
2.138" diameter. Each cover individually packaged with
the necessary screws for mounting.*

10

6

660

d" Raised–4L" Square
For one toggle switch. Each cover individually
packaged with the necessary screws for mounting.*

10

6

655

656

657

658

G

7.5

*Fits any Bowers 4L" square outlet box or extension ring.

659

660

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G55

Bowers ®

654

Std. Wt./Lbs.
Pkg. Per Pkg.

d" Raised–4L" Square
Surface blank. Each cover individually packaged with
the necessary screws for mounting.*

652-NEC

653-NEC

Cu. In.
Capacity

649
649

650-BW

Specifications

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G56

Rings and Covers
4 11⁄16" Square Industrial Device Covers (Continued)
Cat.
No.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

663-BW

d" Raised–4L" Square
For two three-wire twist lock receptacles. L"
spacing between 1.4" diameter openings. Each cover
individually packaged with the necessary screws
for mounting.*

7.5

10

5

664-BW

d" Raised–4L" Square
7.5
Opening to accommodate one Bryant 7301, Hubbell 7301,
or Arrow 4515 receptacle in center. Opening 2.45"
diameter. Each cover individually packaged with the
necessary screws for mounting.*

10

5

665-BW

d" Raised–4L" Square
Opening to accommodate Hubbell 3330 receptacle in
center. Opening 1.75" diameter. Each cover individually
packaged with the necessary screws for mounting.*

10

5

663-BW

664-BW

G

Specifications

665-BW

7.5

Bowers ®

*Fits any Bowers 4L" square outlet box or extension ring.

802

Multi-Gang Rings
Cat.
No.

Specifications

802

f" Raised–4l" Long–6g" Wide
A two gang switch ring.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

9.3

5

3

14.3

5

4

21.3

5

4

25.8

5

4

31.0

1

1

36.3

1

2

41.0

1

2

46.5

1

2

51.5

1

2

Fits Bowers 702 outlet boxes and uses GB-2 covers.
803

803

f" Raised–4l" Long–8f" Wide
A three gang switch ring.
Fits Bowers 702 or 703 outlet boxes and uses GB-3 covers.

804

804

f" Raised–4l" Long–10l" Wide
A four gang switch ring.
Fits Bowers 703 or 704 outlet boxes and uses GB-4 covers.

805

f" Raised–4l" Long–12j" Wide
A five gang switch ring.
Fits Bowers 704 or 705 outlet boxes and uses GB-5 covers.

805

806

f" Raised–4l" Long–14a" Wide
A six gang switch ring.
Fits Bowers 705 or 706 outlet boxes and uses GB-6 covers.

806

807

f" Raised–4l" Long–15n" Wide
A seven gang switch ring.
Fits Bowers 706 or 707 outlet boxes and uses GB-7 covers.

808

f" Raised–4l" Long–17f" Wide
An eight gang switch ring.
Fits Bowers 707 or 708 outlet boxes and uses GB-8 covers.

807

809

f" Raised–4l" Long–19l" Wide
A nine gang switch ring.
Fits Bowers 708 or 709 outlet boxes and uses GB-9 covers.

808

810

f" Raised–4l" Long–21c" Wide
A ten gang switch ring.
Fits Bowers 709 or 710 outlet boxes and uses GB-10 covers.

809

810

G56

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G57

Rings and Covers
Concrete Box Covers

910

Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

910

Flat–4" Octagon
Three d" K.O.’s and two f" K.O.’s without fixture stud.*

–

25

7

911

Flat–4" Octagon
Two d" K.O.’s and two f" K.O.’s with c" fixture stud.*

–

25

8

Fits any Bowers concrete box.

911

Switch Box Extension Ring
Cat.
No.
220-EXT

220-EXT

Specifications
Switch Box Extension Ring
Extends a set-in box flush with the wall surface. Ring
extends box from b" to 1". Slotted on both ends to fit
around screws in plaster ears. Not UL listed.

Cu. In.
Capacity
–

Std. Wt./Lbs.
Pkg. Per Pkg.
25

3

Bowers ®

Fits any Bowers single switch box.

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G

G57

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G58

Multi-Gang Covers
Multi-Gang Covers – SB Series

Typical
Mounting Arrangement

Bowers ®

G

Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

SB-2

Two gang cover

–

1

.30

SB-3

Three gang cover

–

1

.44

SB-4

Four gang cover

–

1

.58

SB-5

Five gang cover

–

1

.72

SB-6

Six gang cover

–

1

.86

SB-7

Seven gang cover

–

1

1.00

SB-8

Eight gang cover

–

1

1.14

SB-9

Nine gang cover

–

1

1.28

SB-10

Ten gang cover

–

1

1.42

Fits Bowers 132, 133, and 134 series handy boxes (both welded and drawn) and 800 series multi-gang rings.

Multi-Gang Covers – GB Series

Typical
Mounting Arrangement

Cat.
No.

Specifications

Cu. In.
Capacity

GB-2

Two gang cover

GB-3

Three gang cover

–

1

.44

GB-4

Four gang cover

–

1

.58

GB-5

Five gang cover

–

1

.72

GB-6

Six gang cover

–

1

.86

GB-7

Seven gang cover

–

1

1.00

GB-8

Eight gang cover

–

1

1.14

GB-9

Nine gang cover

–

1

1.28

GB-10

Ten gang cover

–

1

1.42

–

Std. Wt./Lbs.
Pkg. Per Pkg.
1

.30

Fits Bowers 700 series multi-gang boxes.

How To Order.
1.
2.
3.
4.

Indicate style of cover “GB” or “SB”
Use symbols for each opening
Separate each symbol with a dash (–)
Allow 4 to 6 weeks for shipment.

Example:

G58

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G59

Nonmetallic Boxes
Nonmetallic Single Gang Switch Boxes
Cat.
No.

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

8.0

50

5

8.0

50

5

14.0

50

12

18.0

100

25

G

18.0

100

25

Bowers ®

2g" Deep–3f" Long–2b" Wide
Single Gang Box with threaded screw cavity–18.0 cu. in.
Capacity. Designed with lateral brackets and side
supports for steel stud.

18.0

100

17

118-LBP 2g" Deep–3f" Long–2b" Wide
Single Gang Box with POSI-SET® device mounting clips
–18.0 cu. in. Capacity. Designed with lateral brackets
and side supports for steel stud.

18.0

100

18

120-N

20.3

100

25

20.3

100

25

22.5

100

20

108-E

1c" Deep–3c" Long–2b" Wide
One Layback K.O. in each end. Furnished with plaster
ears and tapped device holes.
Wire Capacity: 4#14; 3#12; 3#10.

108-E

108-FB

1a" Deep–4" Long–2j" Wide
One Layback K.O. in each end. Flat bracket on one side.
Furnished with tapped device holes.
Wire Capacity: 4#14; 3#12; 3#10.

108-FB

114-OW

2z" Deep–3c" Long–2b" Wide
Old work box with swing clamp which adjusts to
wallboard from a" to f" thick. Furnished with four
POSI-WEDGE® clamps.
Wire Capacity: 7#14; 6#12; 5#10.

118-N
114-OW

2g" Deep–3f" Long–2b" Wide
Two Layback K.O.’s in each end. Furnished with
No-Distort angled captive nail supports.
Wire Capacity: 9#14; 8#12; 7#10.

118-NP
118-N

2g" Deep–3f" Long–2b" Wide
Two Layback K.O.’s in each end furnished with
POSI-SET® device mounting clips. Furnished with
No-Distort angled captive nail supports.
Wire Capacity: 9#14; 8#12; 7#10.

118-LB

118-NP

118-LB

3i" Deep–3f" Long–2b" Wide
Two Layback K.O.’s in each end. Furnished with No-Distort
angled captive nail supports.
Wire Capacity: 10#14; 9#12; 8#10.

120-NP
118-LBP

3i" Deep–3f" Long–2b" Wide
Two Layback K.O.’s in each end furnished with
POSI-SET® device mounting clips. Furnished with
No-Distort angled captive nail supports.
Wire Capacity: 10#14; 9#12; 8#10.

122-N
120-N

3e" Deep–3f" Long–2b" Wide
Two Layback K.O.’s in each end. Furnished with
No-Distort angled captive nail supports.
Wire Capacity: 11#14; 10#12; 9#10.

120-NP

120-N

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G59

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G60

Nonmetallic Boxes
Nonmetallic Single Gang Switch Boxes (Continued)
Cat.
No.

120-LB

120-LBP

Specifications

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

120-LB

Single Gang Box with threaded screw cavity–
20.3 cu. in. Capacity. Designed with lateral brackets
and side supports for steel stud.

20.3

100

17

120-LBP

Single Gang Box with POSI-SET® device mounting clips. 20.3–
20.3 cu. in. Capacity. Designed with lateral brackets
and side supports for steel stud.

100

18

122-LB

Single Gang Box with threaded screw cavity–
22.5 cu. in. Capacity. Designed with lateral brackets
and side supports for steel stud.

22.5

100

21

122-LBP

Single Gang Box with POSI-SET® device mounting clips.
22.5 cu. in. Capacity. Designed with lateral brackets
and side supports for steel stud.

22.5

100

21

G
Nonmetallic Multi-Gang Switch Boxes

Bowers ®

122-LB

Cat.
No.
234-N

Specifications
3p" Deep–4" Wide–3f" High
Two gang nail-on switch box. Furnished with eight
POSI-WEDGE® cable clamps and two nails.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

34.0

50

17

34.0

50

17

34.0

50

19

34.0

50

19

45.0

20

10

45.0

25

17

Wire Capacity: 17#14; 15#12; 13#10.

122-LBP

234-NP

3p" Deep–4" Wide–3f" High
Two gang nail-on switch box. Furnished with eight
POSI-WEDGE® cable clamps, POSI-SET® device
mounting clips, and two nails.
Wire Capacity: 17#14; 15#12; 13#10.

234-LB
234-N

3p" Deep–4" Wide–3f" High
Two gang switch box with lateral brackets offset c" from
face. Furnished with eight POSI-WEDGE® cable clamps.
Wire Capacity: 17#14; 15#12; 13#10.

234-NP

234-LBP 3p" Deep–4" Wide–3f" High
Two gang switch box with lateral brackets offset c" from
face. Furnished with eight POSI-WEDGE® cable clamps,
POSI-SET® device mounting clips.
Wire Capacity: 17#14; 15#12; 13#10.

345-N
234-LB

2f" Deep–5m" Wide–3f" High
Three gang nail-on switch box. Furnished with twelve
POSI-WEDGE® cable clamps and two nails.
Wire Capacity: 22#14; 20#12; 18#10.

345-LB
234-LBP

2f" Deep–5m" Wide–3f" High
Three gang switch box with lateral brackets offset c"
from face. Furnished with twelve POSI-WEDGE®
cable clamps.
Wire Capacity: 22#14; 20#12; 18#10.

345-N

G60

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G61

Nonmetallic Boxes
Nonmetallic Multi-Gang Switch Boxes (Continued)
Cat.
No.
460-LB

Specifications

Cu. In.
Capacity

2f" Deep–7l" Wide–3f" High
60.0
Four gang switch box with lateral brackets offset c" from
®
face. Furnished with sixteen POSI-WEDGE cable clamps.

Std. Wt./Lbs.
Pkg. Per Pkg.
8

6

10

10

Wire Capacity: 30#14; 26#12; 24#10.

460-LB

460-SB

2f" Deep–7l" Wide–3f" High
Four gang switch box with stabilizing brackets. Furnished
with sixteen POSI-WEDGE® cable clamps and two nails.
Back support slide bracket.

60.0

Wire Capacity: 30#14; 26#12; 24#10.
460-SB

Nonmetallic Two Gang Old Work Boxes
232-OW

Specifications

232-OW

Bowers® Two Gang Old Work Box

Cu. In.
Capacity
–

Std. Wt./Lbs.
Pkg. Per Pkg.
50

26

Nonmetallic 4" Square Outlet Boxes and Covers
Cat.
No.
4S-32-N

Specifications
4" Square–2l" Deep
4" square outlet box. Angled captive nails and
eight POSI-WEDGE® cable clamps.

Cu. In.
Capacity

Std. Wt./Lbs.
Pkg. Per Pkg.

32.0

50

17

–

50

10

3.5

50

9

5.4

50

8

Wire Capacity: 16#14; 14#12; 12#10.

4S-32-N

4S-B

Flat–4" Square
Flat blank cover for 4S-32N box.

4S-1G

4" Square–d" Raised
Single gang switch ring for 4S-32N box.
Wire Capacity: 1#14; 1#12; 1#10.

4S-2G
4S-B

4" Square–d" Raised
Two gang switch ring for 4S-32N box.
Wire Capacity: 2#14; 2#12; 2#10.

4S-1G

4S-2G

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

G61

G
Bowers ®

Cat.
No.

412034.G01 BOWERS 5/7

5/7/03

4:43 PM

Page G62

Nonmetallic Boxes
Nonmetallic 31⁄2" Diameter Ceiling Boxes
Cat.
No.

Specifications
3d" Diameter–2b" Deep
Angled captive nails and four POSI-WEDGE®
cable clamps.*

16.0

50

9

3R-16-NGP

3d" Diameter–2b" Deep
Angled captive nails and four POSI-WEDGE®
cable clamps with ground plate.*

16.0

50

9

3R-16-OW

3d" Diameter–2b" Deep
Old work ceiling box. Furnished with four
POSI-WEDGE® cable clamps.*

16.0

50

15

3R-16-OWGP

3d" Diameter–2b" Deep
Old work ceiling box. Furnished with four
POSI-WEDGE® cable clamps and ground plate.*

16.0

50

15

3R-16-BH

3d" Diameter–2b" Deep
16.0
Furnished with four POSI-WEDGE® cable clamps
and fully adjustable 16"-24" hanger. Hanger secured
to box with one screw.*

25

13

3R-16-BHGP

3d" Diameter–2b" Deep
Furnished with four POSI-WEDGE® cable clamps,
ground plate, and fully adjustable 16"-24" hanger.
Hanger secured to box with one screw.*

16.0

25

13

3R-16-NGP

Bowers ®

3R-16-OW

3R-16-OWGP

3R-16-BH

Std. Wt./Lbs.
Pkg. Per Pkg.

3R-16-N
3R-16-N

G

Cu. In.
Capacity

*Wire Capacity: 8-#14; 7-#12, 6-#10.
3R-16-BHGP

Nonmetallic 4" Diameter Ceiling Boxes and Covers
Cat.
No.

Specifications
4" Diameter–2h" Deep
Angled captive nails and four POSI-WEDGE®
cable clamps.*

20.3

50

10

4R-20-NGP

4" Diameter–2h" Deep
Angled captive nails and four POSI-WEDGE®
cable clamps*, and ground plates.

20.3

50

10

4R-20-BH

4" Diameter–2h" Deep
20.3
Furnished with four POSI-WEDGE® cable clamps
and fully adjustable 16"-24" hanger. Hanger secured
to box with one screw.*

25

14

4R-20-BHGP

4" Diameter–2h" Deep
Furnished with four POSI-WEDGE® cable clamps
and ground plates and fully adjustable 16"-24"
hanger. Hanger secured to box with one screw.*

20.3

25

14

4R-B

4" Round Cover

–

50

5

4R-K

4" Round Cover with d" K.O.

–

50

5

4R-20-BH

4R-20-BHGP

Std. Wt./Lbs.
Pkg. Per Pkg.

4R-20-N
4R-20-N
4R-20-NGP

Cu. In.
Capacity

*Wire Capacity: 10-#14; 9-#12, 8-#10.

4R-B/4R-K

G62

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G63

Cross-Reference Charts
Steel-Correlative Table
BOWERS

STEEL CITY

APPLETON

THEPITT

PAGE NO.

695
690
696
691
697
692
110

GW-135G
GW-125G
GW-235G
GW-225G
GW-335G
GW-325G
24151-1/2

M1-350
M1-250
M2-350
M2-250
M3-350
M3-250
30-1/2

690
682
691
683
692
684
256

112

24151-N

111

25151-1/2

560-L
560-LXE
30E-1/2

262
264
258

119

24151-NV

560-LVB

607

CTDW

698
693
125
126
127
130
164
145, 146
160

GW-435G
GW-425G
54151-1/2
54151-3/4
54151-1/2&3/4
55151-1/2&3/4
54151-NV
54151-N
54151-NL

M4-350
M4-250
40-1/2
40-3/4
40SPL
40E-SPL
561LVB
561N
561LJB

693
685
274
276
278
286
304
300
302

150
296-1
294
153
161

54151-NE

561-LXE

306

54151-V-1/2

40-VB-1/2

282

155
158

54151-L-1/2

280
302

157
128

55151-1/2

284

G40
G40
G40
G40
G40
G40
G6
G6
G6
G6
G7
G6
G6
G6
G6
G20
G20
G20
G40
G40
G9
G9
G9
G10
G9
G9
G10
G7
G7
G7
G7
G7
G24
G24
G7
G8
G8
G8
G8
G8
G8
G9
G9
G8
G8
G10
G10
G10
G10
G11
G11
G11

329
326, 338
165
166
167
175

54171-1/2
54171-3/4
54171-1/2&3/4
54171-N

177

54171-NV

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

SX-18-561-L
SX-115-561-L
40-D-1/2
40-D-3/4
40-D-SPL
561-L
40-E-1/2
40-E-SPL
561-LVB

www.tnb.com

378
374
288
290
292
316

320

G
Bowers ®

1-MB
1-MBS
2-MB
2-MBS
3-MB
3-MBS
3-O-1/2
3-O-SPL
3-O-LC
3-O-LCE
3-O-EXT-1/2
3-O-B-1/2
3-O-LCB
3-O-B-MXN
3-O-LCH
4-D
4-DW
4-DWS
4-MB
4-MBS
4-O-1/2
4-O-3/4
4-O-SPL
4-O-EXT-SPL
4-O-LCB
4-O-LC
4-O-ULC
4-OW-1/2
4-OW-3/4
4-OW-SPL
4-OW-LC
4-OW-LCE
4-O-LCF
4-O-LCFB
4-OW-MXN
4-OW-B-1/2
4-OW-LCB
4-OW-FB-MXN
4-OW-U-1/2
4-OW-ULC
4-OW-U-MXN
4-OW-EXT-1/2
4-OW-EXT-SPL
4-OW-LC-BHC
4-OW-LC-BHS
4-OD-1/2
4-OD-3/4
4-OD-SPL
4-OD-LC
4-OD-EXT-1/2
4-OD-EXT-SPL
4-OD-LCB

RACO

G63

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G64

Cross-Reference Charts
Steel-Correlative Table
BOWERS

Bowers ®

G

4-OD-ULC
4-OD-FB-MXN
4-S-1/2
4-S-3/4
4-S-SPL
4-S-EXT-1/2
4-S-EXT-SPL
4-SW-1/2
4-SW-3/4
4-SW-SPL
4-SW-LC
4-SW-MXN
4-SW-FB-1/2
4-SW-FB-3/4
4-SW-FB-SPL
4-SW-FBH-1/2
4-SW-FBC
4-SW-FB-MXN
4-SW-LB-1/2
4-SW-LBC
4-SW-LB-MXN
4-SW-AB-1/2
4-SW-1/2-2BC
4-SW-EA-SPL
4-SW-EXT-1/2
4-SW-EXT-3/4
4-S-WR-1/2
4-S-WR-SPL
4-SS-WR-1/2
4-SS-1/2
4-SDW-1/2
4-SDW-3/4
4-SDW-SPL
4-SDW-1
4-SDW-LC
4-SDW-FB-1/2
4-SDW-FB-3/4
4-SDW-FB-SPL
4-SDW-FBC
4-SDW-MXN
4-SDW-FB-MXN
5-SDW-1/2
5-SDW-3/4
5-SDW-SPL
5-SDW-3/4-1
5-SDW-1
5-SDW-1-1/4
5-SDW-FB-1
5-SDW-FB-SPL
5-SDW-EXT-1/2
5-SDW-EXT-3/4

G64

RACO

STEEL CITY

APPLETON

THEPITT

PAGE NO.

176
170
190
191
192
201
203

54171-NL

561-LDJB

318

211

52151-1/2
52151-3/4
52151-1/2&3/4
53151-1/2
53151-1/2&3/4
52151-1/2-W
52151-3/4-W
52151-1/2&3/4-W
52151-N

4S1/2-DR
4S3/4-DR
4S-SPL-DR
4SE-1/2
4SES
4-S-1/2
4-S-3/4
4-S-SPL
4SR

410
412
414
424
428
411
412
415
444

197, 198

52151-CV-1/2

4SVB-1/2
4SVB-1/2-PL

407, 419

G11
G11
G15
G15
G15
G15
G15
G12
G12
G12
G12
G12
G12

199
194, 196
197
220, 223

52151-CV-3/4
52151-CV-1/2&3/4
52151-V-1/2
52151-CVN

4SVB-SPL-PL

421, 427
413
448

193
225

52151-B-1/2
52151-BN

4SB-1/2
4SRB

416
446

181

4SAB-1/2
187

53151-1/2&3/4-UB

202
204

53151-3/4
X-1-1/2-1/2
X-1-1/2-1/2-3/4

422
4SE-3/4

4SLES
4SL-1/2
4SD-1/2
4SD-3/4
4SD-SDL
4SD-1
4SRD

426

186
185
230
231
232
233
242
234

52141-1/2
52171-1/2
52171-3/4
52171-1/2&3/4
52171-1
52171-N
52171-CV-1/2

235
240

52171-CV-1/2&3/4
52171-VN

4SD-VB-SPL-PL
4SRD-VB-PL

451
452

255
256
257
265
258
259

72171-1/2
72171-3/4
72171-1/2&3/4
72171-3/4-1
72171-1
72171-1-1/4

4SJD-1/2
4SJD-3/4
4SJD-SPL
4SJD-3/4&1
4SJD-1
4SJD-1-1/2
4SJD-SPL-VB

262
262

72171-CV-3/4-1
73171-1/2
73171-3/4

552
554
556
558
560
562
561
557

408
430
432
434
436
450
420

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

G12
G13
G13
G13
G13
G13
G13
G14
G14
G14
G14
G14
G14
G16
G16
G16
G15
G16
G16
G16
G16
G17
G17
G17
G17
G17
G17
G17
G18
G18
G18
G18
G18
G18
G18
G18
G19
G19

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G65

Cross-Reference Charts
Steel-Correlative Table
BOWERS

STEEL CITY

APPLETON

THEPITT

PAGE NO.

262
263
245
246
247
250
250

73171-1/2&3/4
73171-1
72151-1/2
72151-3/4
72151-1/2&3/4
73151-1/2
73151-1/2&3/4

4SJDE-1/2&3/4
4SJDE-1
4SJ-1/2
4SJ-3/4
4SJ-SPL

564
566
544
546
548

G19
G19
G19
G19
G19
G20
G20
G42
G42
G42
G42
G42
G42
G42
G25
G25
G25
G25
G25
G25
G25
G26
G26
G26
G26
G26
G26
G26
G26
G26
G27
G27
G27
G27
G27
G27
G27
G28
G28
G28
G28
G28
G28
G28
G28
G28
G29
G30
G30
G30
G30
G30

420
421
445
440
424
500
503

SWB-25
CLV
CDOW

550

111
111LE
383
171-F

130
126
116
120
132
218

CDV

222
225
222VB-PL

501

CDLE

222-LE

214

519
528

LXWOW
LXWLE

384
384-LE

162
158

504
449, 531

LXWV

384-VB-PL

222
170

502
529

804-S

222-NL

425
539

CDOW-TG
LXWOWC

384-OW

560
565
561
566
567
568

CW-1/2
CW-3/4
CWLE-1/2
CWLE-3/4
CWN
CWNLE

333
335
333-LE

562
564

CWV
CWNV

333-VB
389-VB

680
664

591
592
601
602

CY-3/4
CYLE-1/2
CXW

336
333-DLE
384-D
384-DLE

254
248
238
236

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

220
164
163

389

www.tnb.com

676
678
672
674
662
660

G
Bowers ®

5-SDW-EXT-SPL
5-SDW-EXT-1
5-SS-1/2
5-SS-3/4
5-SS-SPL
5-SS-EXT-1/2
5-SS-EXT-SPL
12-BC
14-B
14-BL
20-BC
44-B
44-BD
44-BL
51
51-NE
51-LC
51-MXN
51-FB
52
52-3/4-BW
52-FB-W/O-SPUR
52-FB-3/4
52-NE
52-NE-3/4
52-LC
52-LCNE
52-MXN
52-FB
52-FBC
52-FB-MXN
52-LB
52-LBC
52-LB-MXN
52-OW
52-OWC
52-OW-MXN
53
53-3/4-BW
53-NE
53-NE-3/4
53-LC
53-LCNE
53-MXN
53-FB
53-FBC
53-FB-MXN
54-3/4
54-NE
54-LC
54-LCNE
54-MXN

RACO

G65

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G66

Cross-Reference Charts
Steel-Correlative Table
BOWERS

Bowers ®

G

54-FBC
54-FB-MXN
72
72-C
72-CE
72-OC
72-ONCS
72-ONS-MXN
72-FB-MXN
73-C
73-ONCS
73-FBC
73-FB-MXN
74-CE
74-ONCS
74-FBC
75-ONCS
100-BW
100-DR
100-K
100-SR
100-TL
100-TS
100-GFI
102-1/2
102-W-1/2
102-W-LB-1/4
102-W-EXT-1/2
103-1/2-BW
103-3/4
103-FB-1/2
103-W-1/2
103-W-3/4
103-W-AB
103-W-EXT-1/2
103-W-FB-1/2
104-1/2
104-FB-1/2
104-W-1/2
104-W-3/4
104-W-AB
104-W-FB-1/2
104-W-FB-3/4
105-1/2
106-1/2-BW
106-3/4
106-FB-1/2
106-FB-3/4
132-SPL
132-W-SPL
132-W-1/2
132-W-SPL

G66

RACO

STEEL CITY

APPLETON

THEPITT

PAGE NO.

605

CXWV

384-D-VBPL

242

G30
G30
G31
G31
G31
G31
G31
G32
G32
G32
G33
G33
G33
G33
G33
G33
G34
G44
G44
G44
G44
G44
G44
G44
G35
G34
G34
G35
G36
G36
G36
G35
G35
G35
G35
G35
G37
G37
G36
G36
G36
G36
G36
G37
G37
G37
G37
G37
G39
G38
G38
G38

596
556
555
551
396
355
341

384-LES
A-254
A-257

385-LES
385-LESN

206
210

CWN
16KLESN
CWNV

110

CXWOW
CXWV
860
864
861
863
868
865

650
655
653
660
663
662

661
665

58-C-1
58-C-7
58-C-6
58-C-5
58-C-4
58-C-30

2540
2510
2555
2539
2538
2594

608
616
614
612
610
618

58351-1/2

4SSLS1/2

588

4SSLE1/2
4CS1/2
4CS3/4

591
592
594
596
598

58351-B-1/4
58361-1/2
58361-3/4
58361-V-1/2

4CS3/4
4CSX1/2PL
59361-1/2
58371-1/2
58371-V-1/2

670
674
671
678

683

596
600, 602

4CSVB1/2
4SSL1/2-DR

58371-3/4
58371-T-1/2

4SSL1/2
4SSL3/4
4SSLX1/2-PL
4SSLBV1/2

68361-1/2
68371-1/2

180-1/2
181-1/2

2G4D-1/2&3/4

604
605
606

395

680
132AP-SPL

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G67

Cross-Reference Charts
Steel-Correlative Table
BOWERS

STEEL CITY

APPLETON

THEPITT

681
685
2G4DV-1/2&3/4
LXWV-9

132APFB-SPL

391

36115-C
LCLE
LCOW
LXWV-2G

510-LC
388-LE
388
384-VB-PL2G

266

24-C-1

8301-A

270

703

24-C-6

8320

272

752
753
767
759
757
756
758

52-C-1
52-C-6
52-C-3-1/2
52-C-3-3/4
52-C-3-1
52-C-3
52-C-3-1-1/4

8465
8474
8461-A
8461-B
8461-C
8461
8461-D

472
478
476
475
479
477

772
773
771
768
787
755
771
772
778
779
777
769
791
775
774

52-C-13
52-C-14
52-C-62
52-C-14-5/8
52-C-O
52-C-10

8468
8468-WB
8468-C
8468-F

484
486
482
489
480

52-C-17
52-C-18
52-C-20
52-C-18-5/8
52-C-OO
52-C-16
52-C-15

8468-B
8468-A
8470-A
8470
8470-B
8470-C
8470-F
8466
8466-A

498
500
496
499
494
490
488

781
780
782
783
784
790
785
786
792
793

52-C-21
52-C-19
52-C-49-1/2
52-C-49-3/4
52-C-49-1
52-C-49-1-1/4
52-C-50-1-1/2
52-C-51-2
52-C-1/2
52-C-52-3/4

8469
8469-A
846-50
846-75
846-100
846-125
846-150
846-200
847-50
847-75

502
520
522
524
526
528
530
532
534

292
473
471
543

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

PAGE NO.

G38
G38
G38
G38
G38
G39
G39
G39
G23
G23
G31
G31
G34
G34
G45
G45
G45
G45
G45
G45
G45
G45
G45
G45
G46
G45
G46
G46
G46
G46
G46
G46
G46
G46
G47
G47
G46
G47
G46
G47
G47
G47
G47
G47
G48
G48
G48
G48
G48
G48
G48
G48

G
Bowers ®

132-W-AB-1/2
132-W-FB-1/2
132-W-FB-3/4
132-W-FB-SPL
132-W-FBC
133-B
133-FB-1/2
134-B
210-L
210-LC
230-CC
230-LCC
271-FBC
271-FB-MXN
300-BW
300-DR
300-K
300-SR
400-BW
400-K
401-C
401-CA
401-CB
401-CC
401-CD
401-CS
403-BW
403-A
403-B
403-C
403-F
403-O
403-ST
403-T
404-BW
404-A
404-B
404-C
404-F
405-BW-R
405-A
405-B
406-BW
406-A
407-A
407-B
407-C
407-D
407-F
407-G
408-A
408-B

RACO

G67

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G68

Cross-Reference Charts
Steel-Correlative Table

Bowers ®

G

BOWERS

RACO

STEEL CITY

APPLETON

THEPITT

PAGE NO.

408-C
408-D
408-F
408-G
410
410-L
410-LC
410-LCF
440-B
449-BW
450
451-NEC
452-NEC
453-NEC
454
455

794
797
795
796

52-C-52-1
52-C-52 1-1/4
52-C-53 1-1/2
52-C-52-2

847-100
847-125
847-150
847-200
4CL

536
538
540
542
269

293
295
295

56111

805
806
807
802
801
804

RS-1
RS-2
RS-8
RS-12
RS-11
RS-10

8360
8368
8375
8371
8365
8363
8364

503
504
506
510
516
514

803

RS-5
RS-3
RS-4

G48
G48
G48
G48
G23
G23
G23
G24
G42
G49
G49
G49
G49
G49
G49
G49
49
G49
G49
G49
G49
G49
G50
G50
G50
G50
G50
G50
G50
G50
G50
G50
G50
G50
G51
G51
G51
G51
G51
G51
G51
G51
G51
G51
G51
G52
G52
G51
G52
G52
G52
G52
G52

456
457-NEC
458
459
460-BW
464
465
469
470-BW
471-NEC
472-NEC
473-NEC
474-BW
475
476
477-NEC
478
479-GFI
480-BW
481-BW
482-NEC
500-BW-C
500-DR
500-K
500-K-3/4
500-SR
500-TL
501-C-BW
501-CA
501-CB
501-CC
501-CD
501-CS
503-BW
600-BW
600-K

G68

8367
8379
8377
8361
8378

8369
508

812
810
800
813
811

507
518
512

RS-9
RS-14
RS-15

722
731
724

54-C-1
5402-LR
54-C-6

8403
8420-LR
8413

322
336
328

730

5401-LR

8419-LR

334

737
734
732
727
733

54-C-3-1/2

8409-A

54-C-3-1
54-C-3
54-C-3-1-1/4

8409

332
331
331
326

728
832
833

54-C-14
72-C-1
72-C-6

8434
8487
8487-K

568
572

519

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G69

Cross-Reference Charts
Steel-Correlative Table
RACO

STEEL CITY

APPLETON

THEPITT

601-C
601-CA
601-CB
601-CC
601-CD
603-BW
603-A
603-B
603-C
604-BW
604-A
604-B
604-C
604-F
605-BW
605-A
606-BW
606-A
607-A
607-B
607-C
607-D
607-F
607-G
608-C
608-F
608-G
649
650-BW
651-NEC
652-NEC
653-NEC
654
655
656
657-NEC
658
659
660
663-BW
664-BW
665-BW
702-SPL
703-SPL
704-SPL
705-SPL
706-SPL
707-SPL
708-SPL
709-SPL
710-SPL
802
803

829
830
831
835
834
838
837
836
843
840
841
817
818

72-C-3-1/2
72-C-3-3/4
72-C-3-1
72-C-3

8488-A

72-C-14
72-C-13
72-C-62
72-C-14-5/8
72-C-18
72-C-17

8485
8485-A

578
576
574
586
584

72-C-18-5/8

8486
8486-A
8486-B
8486-C

839
842
819
820
894
895
896
897
898
899
883
885
886

72-C-15
72-C-16
72-C-19
72-C-21
72-C-49-1/2
72-C-49-3/4
72-C-49-1
72-C-49-1-1/4
72-C-5-1-1/2
72-C-52-2
72-C-52-1
72-C-53-1-1/2
72-C-54-2

570

580
582

8495
876
877
872
871

RSL-2
RSL-8
RSL-12
RSL-11

8493
8492
8491
8494

728
722
724

873

RSL-5

8490

726

878
870

RSL-4
RSL-9

8496
8498
8489

730
732
720

888
879
951
952
953
954
955
956
957
958

RSL-14
RSL-15
2-G-1/2-3/4
3-G-1/2-3/4
4-G-1/2-3/4
5-G-1/2-3/4
6-G-1/2-3/4

8499
8497
2G-5075
3G-5075
4G-5075
5G-5075
6G-5075
7G-5075
8G-5075

734
736
629
630
631
640
641

821
822

2GC
3GC

2GC-75
3GC-75

657
653

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

PAGE NO.

G52
G52
G52
G52
G52
G53
G53
G53
G53
G53
G53
G53
G53
G53
G53
G53
G53
G53
G54
G54
G54
G54
G54
G54
G54
G54
G54
G55
G55
G55
G55
G55
G55
G55
G55
G55
G55
G55
G55
G56
G56
G56
G20
G21
G21
G21
G21
G21
G21
G21
G21
G56
G56

G
Bowers ®

BOWERS

G69

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G70

Cross-Reference Charts
Steel-Correlative Table

Bowers ®

G

G70

BOWERS

RACO

STEEL CITY

APPLETON

THEPITT

PAGE NO.

804
805
806
807
808
809
810
900
901-BW
902
903
904
906-BW
905
910
911
BH-C

823
824
825
826
827
828

4GC
5GC
6GC

4GC-75
5GC-75
6GC-75
7GC-75
8GC-75

655
661
667

270
271
272
273
274
276
275
890
891
922

OCR-2
OCR-2-1/2
OCR-3
OCR-3-1/2
OCR-4

620
622
628
636
644

OCP
OCP-3/8
SX18, SX26

648
650
352

BH-S

920

SX115, SX160

350

G42

BH-200
GB-2
GB-3
GB-4
GB-5
GB-6
GB-7
GB-8
GB-9
GB-10
LVP
LVPH
MBP
MBPS
MBT-4
MBT-6
MBT-8
NP-3008
PT-26
SB-2
SB-3
SB-4
SB-5
SB-6
SB-7
SB-8
SB-9
SB-10

977
844
845
846
847
848
849
850
851

54531-1/2-3/4
54541-1/2-3/4
54551-1/2-3/4
54561-1/2-3/4
54571-1/2-3/4
54591-1/2-3/4
54581-1/2-3/4
CBP
CBP-3/8
6011-P,
6011-DW,
6011-AP,
6011-DW
6010-P,
6010-DW,
6010-AW,
6010-ADW
820-D
2-GCS
3-GCS
4-GCS
5-GCS
6-GCS

G56
G56
G56
G56
G56
G56
G56
G22
G22
G22
G22
G22
G22
G22
G57
G57
G42

896

708
802
803
804
805
806

G43
G58
G58
G58
G58
G58
G58
G58
G58
G58
G22
G22
G40
G40
G41
G41
G41
G43
G43
G58
G58
G58
G58
G58
G58
G58
G58
G58

974
971
971
633
634
635
2710, 2709

SGP
DGP

CBTW-4
CBTW-6
CBTW-8
CP-1

LVP-1
LVP-1
LVP-250
LVP-350
MW1-350
MW1-550
MW1-750
P-300
14813

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G71

Cross-Reference Charts
Nonmetallic-Correlative Table
BOWERS

B-518A
B-518P
B-518R
B-520A
B-520P
B-620H
B-620HG
A-410
B-432A
A-400
A-420

RACO

ALLIED

7305
7906
7118
7918
7121
7921
7824
7823
7338
7938
7772
7234

9336-UBK
9336-UBGK
9336-NK
9336-NGK
9338-ESK
9338-ESGK
9351-NK
9351-NGK
9350-UBK
9350-UBGK
9345
9343-NC2
9344
9346
9307-E

7778

B-114R
B-118B

7887

9331-EW
1096-Z2

B-118A
B-118F
B-120A
B-120F

7302
7301
7820

1096-N
1096-NT
1098-N

B-232B
B-232BF
B-232A
B-232F

SLATER

C1-18-HAC
N-321-C-94/95
C1-18-HGAC
N-321-GC-94/95
C1-18-RAC
N-321-C
C1-18-RGAC
N-321-GC
C1-18-WAC
3080-9
C1-18-WGAC
3080-9-40
S1-20-RAC
N-423-C-V
S1-20-RGAC
N-423-GC-V
S1-20-HAC
N-423-C-94-V/95V
S1-20-HGAC N-423-GC-94-V/95V
RC-1
4SP1-214
S44-35-RAC
4S-1310-C
4SPB
RC-2
4SP2-312
7090
S1-18-W
S1-18-S50
P1-18-R
S1-18-R
S1-22-R

B-344A

7534
7734
7835
7836
7642
7846

B-455A

7644

1099-N
2300-2Z2
2300-NK
2300-NCZ
3300-2Z2
3300-NK
4300-2Z2
4300-Z2BK

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

CHALENGER/
UNION

S2-35-S50AC
S2-35-S25AC
S2-35-RAC
S3-54-S25AC
S3-54-RAC
S4-73-S50AC

www.tnb.com

E14-4
SB18
SB18FS
SN-18
SN18FS
SN-21
SN21FS
RN-23
2002-738
SB2-236-FS
SN236
SN236-FS
7073-202
SN357
2004-238
7074-BH
SST

PAGE NO.

G62
G62
G62
G62
G62
G62
G62
G62
G62
G62
G61
G61
G61
G61
G59
G59
G59
G59
G59
G59
G59
G59
G59
G59
G60
G60
G60
G60
G60
G60
G61
G61
G62

G
Bowers ®

3R-16-BH
3R-16-BHGP
3R-16-N
3R-16-NGP
3R-16-OW
3R-16-OWGP
4R-20-N
4R-20-NGP
4R-20-BH
4R-20-BHGP
4S-1G
4S-32N
4S-B
4S-2G
108-E
108-FB
114-OW
118-LB
118-LBP
118-N
118-NP
120-N
120-NP
122-N
234-LB
234-LBP
234-N
234-NP
345-LB
345-N
460-LB
460-SB
MSTCRIMPING
TOOL

CARLON

G71

412034.G01 BOWERS 5/7

5/7/03

4:44 PM

Page G72

Notes

Bowers ®

G

G72

© 2003 Thomas & Betts Corporation. Specifications are subject to change without notice.

www.tnb.com



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2003:05:14 19:17:49Z
Modify Date                     : 2003:05:14 15:09:04-05:00
Subject                         : Indoor Boxes and Covers
Page Count                      : 72
Creation Date                   : 2003:05:14 19:17:49Z
Mod Date                        : 2003:05:14 15:09:04-05:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : J Canestrari
Metadata Date                   : 2003:05:14 15:09:04-05:00
Title                           : G-BOWERS.pdf
Page Mode                       : UseOutlines

EXIF Metadata provided by EXIF.tools