Primary Switch Mode Power Supply CP D 12/0.83
118567-Attachment 118567-Attachment 118567-Attachment 804325 Batch7 unilog cesco-content
2014-07-30
: Pdf 118567-Attachment 118567-Attachment 804325 Batch6 unilog
Open the PDF directly: View PDF 
.
Page Count: 9
| Download | |
| Open PDF In Browser | View PDF |
Power supply CP-D 12/0.83 2CDC 271 024 F0t07 Primary switch mode power supply Data sheet Features � � � � � a OUTPUT +, ‑: terminals ‑ output b INPUT L, N: terminals ‑ input c DC ON: green LED ‑ output voltage applied d DC LOW: red LED ‑ output voltage too low Rated output voltage 12 V DC Rated output current 0.83 A Rated output power 10 W Wide range input 100‑240 V AC (90‑264 V AC, 120‑375 V DC) Efficiency of typ. 78 % Low power dissipation and low heating Free convection cooling (no forced cooling with ventilators) Ambient temperature range during operation ‑40...+70 °C Open‑circuit, overload and short‑circuit stable Integrated input fuse U/I characteristic (fold‑forward behaviour at overload ‑ no switch‑off) LEDs for status indication Structural form ideal for installation in distribution panels Light‑grey enclosure in RAL 7035 Approvals A UL 508, CAN/CSA C22.2 No.14 H UL 1310, CAN/CSA C22.2 No.223 (Class 2 Power Supply) H UL 60950, CAN/CSA C22.2 No.60950 GOST D CCC E *) Approval refers to rated input voltage Uin ~ *) *) *) *) e Circuit diagram Marks a b CE C‑Tick pending Order data Type Input voltage range Rated output voltage / current Order code CP-D 12/0.83 90‑264 V AC / 120-375 V DC 12 V DC / 0.83 A 1SVR 427 041 R1000 Application The primary switch mode power supply has two voltage input ranges. This enables the supply with AC or DC. Furthermore it is equipped with two generous capacitors, which ensure mains buffering of at least 30 ms. That is why the device can be used worldwide also in high fluctuating networks and battery‑powered plants. Installation The switch mode power supply can be snapped on a DIN rail according to IEC/EN 60715 as shown in the accompanying picture. For that the device is set with its mounting rail slide on the upper edge of the mounting rail and locked by lifting it downwards. ABB 2CDC 272 040 F0b07 Mounting 1 Power supply CP-D 12/0.83 Primary switch mode power supply Data sheet Installation Demounting 2CDC 272 041 F0b07 Remove the switch mode power supply as shown in the accompanying picture. For that the latching lever is pulled downwards by means of the screwdriver. Alternatively you can press the unlock button to release the device. Then in both cases the device can be unhinged from the mounting rail edge and removed. Mounting position 2CDC 272 042 F0b07 The devices have to be mounted horizontally with the input terminals on the bottom. In order to ensure a sufficient convection, the minimum distance to other modules should not be less than 25 mm in vertical direction and horizontal direction. Electrical connection Connect the input terminals L and N. The installation must be executed acc. to EN 60950, provide a suitable disconnecting device (e. g. line protection switch) in the supply line. The input side is protected by an internal input fuse. Rate the lines for the maximum output current or provide a separate fuse protection. We recommend to choose the cable section as large as possible in order to minimize voltage drops. Observe the polarity. Actuate plug connector only when power is off. The device is overload, short‑circuit and open‑circuit proof. The secondary side of the power supply is electrically isolated from the input and internally not earthed (SELV) and can therefore be earthed by the user according to the needs with + or ‑ (PELV). Connection diagram(s) - L + PWM N L 2 - N 2CDC 272 038 F0b07 + +, ‑ L, N Output voltage Input voltage ABB Power supply CP-D 12/0.83 Primary switch mode power supply Data sheet Safety instructions and warnings The device must be installed by qualified persons only and in accordance with the specific national regulations (e. g. VDE, etc.). CP‑D power supplies are chassis‑mounted units. They are maintenance‑free and do not contain any integral setting elements and should therefore not be opend. Before any installation, maintenance or modification work: Disconnect the system from the supply network and protect against switching on! Before start of operation the following must be ensured: Connect to main according to the specific national regulations. Power supply cables and unit must be sufficiently fused. A disconnecting device has to be provided for the end product to disengage unit and supply cables from supply mains if required. Rate the output lines for the output current of the power supply and connect them with the correct polarity. In order to ensure sufficient air‑cooling the distance to the other devices has to be considered. Attention! Improper installation/operation may impair safety and cause operational difficulties or destruction of the unit. In operation pay attention to: Do not modify the installation (primary and secondary side)! High current! Risk of electric arcs and electric shock (danger to life)! Risk of burns: Depending on the operation conditions the enclosure can become very hot. If the internal fuse blows, most probably the device is defect. In this case, an examination of the switch mode power supply by the manufacturer is necessary. Attention! Danger to life! Disconnect the system from the supply network before executing any works at the device and protect against switching on! The power supply contains components with high stored energy and circuits with high voltage! Do not introduce any objects into the unit and do not open the unit. With some units of this range the output is capable of providing hazardous energy. Ensure that the service personnel is protected against inadvertent contact with parts carrying energy. ABB 3 Power supply CP-D 12/0.83 Primary switch mode power supply Data sheet Technical data Data at Ta = 25 °C, Uin = 230 V AC and rated values, unless otherwise indicated Input circuits - Supply circuits 1SVR 427 041 R1000 Rated input voltage Uin L, N Typical input current / power consumption 100‑240 V AC Input voltage range Frequency range 90‑264 V AC 120‑375 V DC AC 47‑63 Hz 30 A max. 3 ms min. 30 ms Internal input fuse (apparatus protection, not accessible) 1 A slow‑acting / 250 V AC Power factor correction (PFC) no Indication of operational states 1SVR 427 041 R1000 DC ON: green LED V: output voltage applied DC LOW: red LED V: output voltage too low Output circuits 1SVR 427 041 R1000 +, ‑ Tolerance of the output voltage Derating of the output current Deviation 10 W Ta ≤ 60 °C Rise time Residual ripple and switching peaks 0.83 A 60 °C < Ta ≤ 70 °C 2.5 %/°C load change statical max. 1 % change of output voltage within the input voltage range max. 1 % Control time Starting time after applying supply voltage 12 V DC ± 1 % Rated output power Rated output current Ir 230 V AC 128.3 mA / 13.01 W AC Power failure buffering time Rated output voltage 110 V AC 200 mA / 12.68 W DC Inrush current limiting Output voltage 100‑240 V AC < 1 ms at Ir 1000 ms at rated load typ. 1 ms BW = 20 MHz 50 mV Parallel connection yes, use of CP-D RU required Series connection yes, to increase voltage Resistance to reverse feed 18 V / 1 s Characteristic curve of output U/I characteristic curve Short‑circuit protection continuous short‑circuit stability Short‑circuit behaviour continuation with output power limiting Current limiting at short circuit typ. 1.4 A Overload protection output power limiting Overvoltage protection 15-16.5 V DC No‑load protection continuous no‑load stability Starting of capacitive loads unlimited General data 1SVR 427 041 R1000 Duty time 100 % Dimensions (W x H x D) Material of housing 4 18 x 91 x 57.5 mm (0.71 x 3.58 x 2.26 inches) housing Plastic ABB Power supply CP-D 12/0.83 Primary switch mode power supply Data sheet General data 1SVR 427 041 R1000 Efficiency typ. 78 % Weight 0.066 kg (0.13 lb) Mounting position horizontal Minimum distance to other units normal operation mode horizontal 25 mm (0.98 inch) vertical 25 mm (0.98 inch) Mounting Degree of protection DIN rail (IEC/EN 60715), snap‑on mounting without any tool housing / terminals Class of protection II Electrical connection 1SVR 427 041 R1000 Input circuit / Output circuit Wire size Screw connection fine‑strand with wire end ferrule 0.2‑1.5 mm2 (24‑16 AWG) rigid 0.2‑2.5 mm2 (26‑12 AWG) Stripping length 4-5 mm (0.16-0.2 in) Tightening torque 0.6 Nm (5 lb.in) Environmental data Ambient temperature range IP20 / IP20 1SVR 427 041 R1000 operation ‑40...+70 °C full load ‑40...+60 °C storage ‑40...+85 °C Damp heat, cyclic (IEC/EN 60068‑2‑30) 4 x 24 h cycles, 40 °C, 95 % RH Vibration, half‑sine (IEC/EN 60068‑2‑6) 50 m/s2, 10 Hz ‑ 2 kHz Shock, half‑sine (IEC/EN 60068‑2‑27) 40 m/s2, 22 ms Isolation data Rated isolation voltage Ui 1SVR 427 041 R1000 input circuit / output circuit 3 kV AC Pollution degree 2 Overvoltage category (UL/IEC/EN 60950-1) II Standards / Directives 1SVR 427 041 R1000 Product standard EN 61204 EMC Directive 2004/108/EC Low Voltage Directive 2006/95/EC Electrical safety UL 508, UL 60950‑1, EN 60950‑1 Protective low voltage SELV (EN 60950‑1) Electromagnetic compatibility 1SVR 427 041 R1000 Interference immunity to IEC/EN 61000‑6‑2 electrostatic discharge IEC/EN 61000‑4‑2 Level 4 (4 kV / 8 kV) radiated, radio-frequency, electromagnetic field IEC/EN 61000‑4‑3 Level 3 (10 V/m) electrical fast transient / burst IEC/EN 61000‑4‑4 Level 4 (4 kV) surge IEC/EN 61000‑4‑5 Level 3 (2 kV L‑L) conducted disturbances, induced by radiofrequency fields IEC/EN 61000‑4‑6 Level 3 (10 V) ABB 5 Power supply CP-D 12/0.83 Primary switch mode power supply Data sheet Electromagnetic compatibility 1SVR 427 041 R1000 Interference emission 6 IEC/EN 61000‑6‑3 high-frequency radiated IEC/CISPR 22, EN 55022 Class B high-frequency conducted IEC/CISPR 22, EN 55022 Class B ABB Power supply CP-D 12/0.83 Primary switch mode power supply Data sheet Technical diagrams Output behaviour 12 11 10 9 8 7 6 5 4 3 2 1 0 0.25 0 0.5 0.75 1 1.25 Iout [A] 2CDC 272 019 F0207 Uout [V] Characteristic curve of output at Ta = 25 °C The switch mode power supply CP‑D 12/0.83 is able to supply at 12 V DC output voltage and at an ambient temperature of: ≤ 60 °C a continuous output current of approx. 0.83 A at ambient temperatures of: 60 °C < Ta ≤ 70 °C the output power has to be reduced by 2,5 % per °C temperature increase. If the switch mode power supply is loaded with an output current > 0.83 A, the operating point is passing through the U/I characteristic curve shown. Temperature behaviour 100 90 80 70 60 50 40 30 20 10 -10 0 10 20 30 40 50 60 70 Ta [°C] 2CDC 272 018 F0207 Pout [%] Characteristic curve of temperature at Uout Dimensions in mm 18,0 [0.71”] 67,0 [2.64”] 57,5 [2.26”] 2CDC 272 011 F0b07 49,0 [1.93”] 32,1 [1.26”] 91,0 [3.58”] 44,5 [1.75”] CP-D 12/0.83 ABB 7 Power supply CP-D 12/0.83 Primary switch mode power supply Data sheet Further Documentation Document title Document type Document number Electronic Products and Relays Technical catalogue 2CDC 110 004 C02xx Power Supply Units Application manual 2CDC 114 048 M020x You can find the documentation on the internet at www.abb.com/lowvoltage R Control Products R Power Supplies 8 ABB Contact us Document number 2CDC 114 052 D0201 (02/12) ABB STOTZ-KONTAKT GmbH P. O. Box 10 16 80 69006 Heidelberg, Germany Phone: +49 (0) 6221 7 01-0 Fax: +49 (0) 6221 7 01-13 25 E-mail: info.desto@de.abb.com You can find the address of your local sales organisation on the ABB home page http://www.abb.com/contacts -> Low Voltage Products and Systems Note: We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB AG does not accept any responsibility whatsoever for potential errors or possible lack of information in this document. We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole or in parts – is forbidden without prior written consent of ABB AG. Copyright© 2010 ABB All rights reserved
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Create Date : 2012:02:13 14:30:07+01:00 Metadata Date : 2012:02:13 14:31:06+01:00 Modify Date : 2012:02:13 14:31:06+01:00 Creator Tool : Adobe InDesign CS5 (7.0.4) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 8037 bytes, use -b option to extract), (Binary data 6090 bytes, use -b option to extract) Instance ID : uuid:75d6282b-0dae-4a18-a496-7f3e6c59f3c1 Document ID : xmp.did:638D5ADC3608E011AAF496DAE2721608 Original Document ID : adobe:docid:indd:9bb419ce-f5c5-11dc-8fb5-88e1111732ec Rendition Class : proof:pdf Version ID : 1 Derived From Instance ID : xmp.iid:628D5ADC3608E011AAF496DAE2721608 Derived From Document ID : adobe:docid:indd:9bb419ce-f5c5-11dc-8fb5-88e1111732ec Derived From Original Document ID: adobe:docid:indd:9bb419ce-f5c5-11dc-8fb5-88e1111732ec Derived From Rendition Class : default History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:E671DD760E02E0118749FA0A809647F6, xmp.iid:E771DD760E02E0118749FA0A809647F6, xmp.iid:8638AD26A602E011BA07E07F83136F78, xmp.iid:7358C256A702E011BA07E07F83136F78, xmp.iid:628D5ADC3608E011AAF496DAE2721608, xmp.iid:638D5ADC3608E011AAF496DAE2721608, xmp.iid:4C7DF3913708E011AAF496DAE2721608, xmp.iid:BF6A668F3156E11192B6DED1E5FF53FB, xmp.iid:C06A668F3156E11192B6DED1E5FF53FB, xmp.iid:D5947B9C3956E11192B6DED1E5FF53FB, xmp.iid:F77A6F6D3C56E11192B6DED1E5FF53FB History When : 2010:12:07 15:30:18+01:00, 2010:12:07 15:30:18+01:00, 2010:12:08 09:42:36+01:00, 2010:12:08 10:08:19+01:00, 2010:12:15 11:34:44+01:00, 2010:12:15 11:34:44+01:00, 2010:12:15 14:16:11+01:00, 2012:02:13 11:57:45+01:00, 2012:02:13 11:57:45+01:00, 2012:02:13 12:55:23+01:00, 2012:02:13 13:15:33+01:00 History Software Agent : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0 History Changed : /, /metadata, /, /, /metadata, /;/metadata, /, /;/metadata, /metadata, /;/metadata, /;/metadata Format : application/pdf Title : Primary switch mode power supply CP-D 12/0.83 Creator : ABB Stotz-Kontakt GmbH Description : Data sheet Authors Position : Data sheet - CP-D 12/0.83 - Primary switch mode power supplies Startup Profile : Print Doc Change Count : 328 Producer : Adobe PDF Library 9.9 Trapped : False GTS PDFX Version : PDF/X-4 Page Count : 9 Author : ABB Stotz-Kontakt GmbH Subject : Data sheet Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools