HomeWorks QS Wired Maestro Designer Local Controls Spec Sheet Part #369700a 122644 Catalog
122639-Catalog 1 122639-Catalog_1 122639-Catalog_1 Batch9 unilog cesco-content
122640-Catalog 1 122640-Catalog_1 122640-Catalog_1 Batch9 unilog cesco-content
2014-10-23
: Pdf 122644-Catalog 122644-Catalog Batch9 unilog
Open the PDF directly: View PDF .
Page Count: 9
Download | |
Open PDF In Browser | View PDF |
product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® HomeWorks® QS Wired Maestro® local controls function much like standard dimmers and switches, but can be controlled as part of a lighting control system. Local lighting controls are useful in locations where single circuits of lighting need to be dimmed or switched. Local fan speed controls are useful in locations where control of a single ceiling paddle fan is needed. Dimmer Switch Remote Dimmer Remote Switch HomeWorks® QS Wired Maestro® dimmers incorporate advanced features such as fade on / fade off, delayed long fade to off, and rapid full on. HomeWorks® QS Wired Maestro® local controls include a Front Accessible Service Switch (FASSTM) for safe lamp replacement. HomeWorks® QS Wired Maestro® local controls install in single-pole or multilocation applications. Remote dimmers / switches are available for multi-location control. Use Lutron® Designer (Claro® or Satin Colors®) wallplates or designer-style wallplates from other manufacturers. Wallplates are sold separately. Lutron® Claro® and Satin Colors® wallplates snap on with no visible means of attachment. HomeWorks® QS Wired Maestro® local controls support color change kits. Fan Speed Model Numbers Dimmers Incandescent/Magnetic Low-voltage HWD-6D-XX* 600 W/600 VA Dimmer HWD-6ND-XX* 600 W/600 VA Dimmer HWD-10D-XX* 1000 W/1000 VA Dimmer HWD-10ND-XX* 1000 W/1000 VA Dimmer Remotes (for multi-location installations) HQD-RD-XX* Remote Dimmer (120 V~) HQD-RS-XX* Remote Switch (120 V~) Electronic Low-voltage HWD-5NE-XX* 500 W Neutral Dimmer RK-S-XX* RK-AD-XX* RK-AS-XX* RK-F-XX* Switches HWD-8ANS-XX* 8 A Lighting, 5.8 A Motor Neutral Electronic Switch Fan Speed Control Single ceiling paddle fan only (120 V~) HWD-2ANF-XX* 2 A Neutral Fan Speed Control 1 | Lutron® Color Change Kits RK-D-XX* Dimmers (-6D, -6ND, -10D, -10ND) Switches (-8ANS ) Remote Dimmer (-RD) Remote Switch (-RS) Fan Speed Control (-2ANF) Note: No color change kit is available for -5NE *“XX” in the model number represents color/finish code. See Colors and Finishes at end of document. 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Specifications Model Numbers Power Dimmer: HWD-6D-XX, HWD-6ND-XX, HWD-10D-XX, HWD-10ND-XX, HWD-5NE-XX Switch: HWD-8ANS-XX Fan Speed Control: HWD-2ANF-XX Remote: HQD-RD-XX, HQD-RS-XX Color Change Kits: RK-D-XX, RK-S-XX, RK-AD-XX, RK-AS-XX, RK-F-XX 120 V~ 50 / 60 Hz Typical Power Consumption Dimmer / Switch / Fan Speed Control: 0.75 W Test conditions: load is off and nightlight mode is enabled. Remote Dimmer / Switch: 0 W Test conditions: load is off. Regulatory Approvals Environment UL, CSA (all except -5NE), and NOM Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0% to 90% humidity, non-condensing. Indoor use only. Communications Wired Local Controls are wired to a HomeWorksR dimmer Hub (HWI-H48). One pair twisted shielded 22 AWG to 18 AWG (0.5 mm2 to 1.0 mm2) IEC PELV/ NECR Class 2 wiring. Capacity Each HomeWorksR Dimmer Hub (HWI-H48) is capable of directly controlling up to 48 Wired MaestroR Local Controls. Up to 8 Wired Local Controls may be wired to a single bus on the HWI-H48. Refer to IEC PELV/NECR Class 2. ESD Protection Tested to withstand electrostatic discharge without damage or memory loss, in accordance with IEC 61000-4-2. Surge Protection Tested to withstand surge voltages without damage or loss of operation, in accordance with IEEE C62.41-1991 Recommended Practice on Surge Voltages in Low-Voltage AC Power Circuits. Power Failure Power failure memory: should power be interrupted, the control will return to its previous state when power is restored. Mounting Requires a U.S. wallbox. 3 ½ in (89 mm) deep recommended, 2 ¼ in (57 mm) deep minimum. Wiring Warranty 2 | Lutron® Uses conventional 3-way and 4-way wiring. http://www.lutron.com/TechnicalDocumentLibrary/warranty.pdf 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Design Features Dimmer • On a single-tap, lights fade ON or OFF. • On a double-tap, lights go to full ON. • When ON, press and hold the tapswitch to engage the delayed long fade to OFF. • Light levels can be fine-tuned by pressing and holding the dimming rocker until the desired light level is reached. • Two-wire dimmers available. • Electronic low voltage dimmer available. Switch • On a single-tap, lights or motors turn ON or OFF. • Requires a neutral connection. Fan Speed Control • On a single-tap, fan turns ON or OFF. • Fan speeds can be selected by pressing and holding the fan speed control rocker until the desired fan speed is reached. • Controls one paddle type ceiling fan (Permanent split-capacitor motor) up to 2 A. Not for use with shaded-pole type motors (i.e. bath exhaust fans). • Provides four (4) quiet speeds plus OFF. • Not for use with fans that have integrated fan speed and/or light control modules. • Requires a neutral connection. Dimensions All dimensions are shown as in (mm) Front View Side View Side View Side View -2ANF only -5NE only 4 11⁄16 (119) 2 15⁄16 (75) 5/16 (8) 1 1⁄8 (30) 5/16 (8) 1 11⁄16 (43) 5/16 (8) 1 3⁄8 (35) Terminal / Wire Color The HWD-5NE dimmer does not have terminals - it has wires. Refer to the chart to the right for wire color equivalents when viewing the wiring diagrams for the -5NE. 3 | Lutron® Terminal Color Black Brass Silver Blue -5NE Wire Color Black Yellow White Blue 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Mounting and Parts Identification Control Mounting Wallplate Screws Adapter Adapter Mounting Wallplate Screws Wallbox Control Wallplate Adapter / Wallplate purchased separately. Ganging and Derating When combining controls in the same wallbox, derating is required. See Load Type and Capacity. No derating is required for remote dimmers / switches / fan speed controls. -8ANS has fins that need to be removed for multigang installations. -8ANS only: Do not remove outside fins on end of gang controls Each control has inside fins removed 4 | Lutron® Middle of gang control has all fins removed 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Load Type and Capacity Control HWD-6D1 HWD-6ND Load Type Minimum Load Not Ganged End of Gang Middle of Neutral Gang Connection Incand. 50 W 600 W 500 W 400 W MLV2 50 W / VA 450 W / 600 VA 400 W / 500 VA 300 W / 400 VA Incand. 10 W 600 W 500 W 400 W MLV2 10 W / VA 450 W / 600 VA 400 W / 500 VA 300 W / 400 VA Incand. 50 W 1000 W 800 W 650 W MLV2 50 W / VA 800 W / 1000 VA 600 W / 800 VA 500 W / 650 VA Incand. 10 W 1000 W 800 W 650 W MLV2 10 W / VA 800 W / 1000 VA 600 W / 800 VA 500 W / 650 VA YES ELV/Incand. 10 W 500 W 450 W 400 W YES Lighting 10 W 8A 6.5 A 5A Motor 0.083 A 1/4 HP 5.8 A 5.8 A 5A Ceiling Fan 0.083 A 2A 2A 2A 1, 5 HWD-10D1 HWD-10ND1, 5 HWD-5NE HWD-8ANS4, 7 HWD-2ANF6 NO YES NO YES YES 1 Dimmer Load Type: -6D, -6ND,-10D, and -10ND are designed for use with permanently installed incandescent, magnetic low-voltage, or tungsten halogen only. Do not install dimmers to control receptacles or motor-operated appliances. 2 Low-Voltage Applications: Use -6D, -6ND, -10D and -10ND with magnetic (core and coil) low-voltage transformers only. Not for use with electronic (solid-state) low-voltage transformers. To control electronic low-voltage transformers, use the HWD-5NE control. Operation of a low-voltage circuit with lamps inoperative or removed may result in transformer overheating and premature failure. Lutron strongly recommends the following: • Do not operate low-voltage circuits without operative lamps in place. • Replace burned-out lamps as soon as possible. • Use transformers that incorporate thermal protection or fused transformer primary windings to prevent transformer failure due to overcurrent. 3 Switch Load Type: -8ANS is designed for use with all permanently installed lighting loads and with motor loads up to 1/4 HP (5.8 A) 4 Ceiling Fan Application (HWD-2ANF): • Use to control one paddle-type ceiling fan (permanent split-capacitor). • Use the ceiling fan’s pull chain to set its speed to the highest setting*. • Do not use to control fans that use shaded-pole motors (i.e. bath exhaust fans). • Do not use to control fans that have integrated fan speed controls (i.e. fans that have a remote control), unless the integrated control is removed from the ceiling fan. • Do not connect to any other motor-operated appliance or to any lighting load type. • Do not use to control a fan lighting load (i.e. lighting kit). *See Application Note # 217 “HomeWorksR MaestroR Controls Reference” for more information. 5 Can control the following power boosters/load interfaces: Hi-PowerR Boosters (HP-2, HP-4, HP-6), 0-10 Volt Interface (GRX-TVI), Minimum Load Interface (LUT-LBX), Phase Adaptive Power Module (PHPM-PA), Switched Power Module (PHPM-SW), and 3-Wire Flourescent Power Module (PHPM-3F). 5 | Lutron® 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Operation Dimmer Switch Status LEDs (not on Remote Dimmers) Indicate light level; glow softly as night light when light is off Dimming Rocker Press to brighten Status LED (not on Remote Switches) Indicates load status; glows softly as night light when light is off Tapswitch Tap on / off Press to dim Tapswitch Tap on / off HWD-5NE only FASSTM Front Accessible OR Service Switch OFF ON FASSTM Front Accessible Service Switch Fan Speed Control Status LEDs Indicate speed level; glow softly as night light when fan is off Speed Control Rocker Press to increase speed Press to decrease speed Tapswitch Tap on / off IMPORTANT NOTICE: FASSTM - Front Accessible Service Switch To replace bulb, remove power by pulling the FASSTM switch out fully on all controlling devices. After replacing bulb(s), push the FASSTM switch(es) back in fully to restore power to the control(s). FASSTM Front Accessible Service Switch 6 | Lutron® 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Wiring Dimmer communications wiring may be in a daisy chain, star, or t-tap configuration. Each home run on a bus may be up to 500 ft (152 m) and may contain up to 8 devices. The total length of wire on each bus (all home runs) may be up to 1000 ft (305 m). Up to 48 HomeWorksR Wired MaestroR Local Controls may be wired to the HomeWorksR Dimmer Hub (HWI-H48). Up to four HWI-H48 Dimmer Hubs may be placed on each processor link configured as an H48 link in the HomeWorksR software. Dimmer Side View IEC PELV/NECR Class 2 wiring to HomeWorks Dimmer Hub or other Wired MaestroR devices Butt Splices Drywall Wall Box Dimmer Backcover IEC PELV/NECR Class 2 Wire Type One pair twisted shielded 22 AWG to 18 AWG (0.5 mm2 to 1.0 mm2) IEC PELV/NECR Class 2 wiring. HWI-H48 Dimmer Hub Gray Violet Gray Violet Gray Violet Up to 8 devices may be wired to each bus on the H48. One pair twisted shielded 22 AWG to 18 AWG (0.5 mm2 to 1.0mm2) IEC PELV/NECR Class 2 wiring. Maximum 500 ft (152 m) per home run, maximum 1000 ft (305 m) total per bus (non-polarized). 7 | Lutron® 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Wiring Diagrams Wiring Diagram 1 Wiring Diagram 2 1 1 Single Location Installation without Neutral -6D and -10D Single Location Installation with Neutral -6ND, -10ND, -5NE, -2ANF and -8ANS Dimmer/Switch Violet Dimmer / Switch / Fan Speed Control Violet To HomeWorks Dimmer Hub or next Wired } (HWI-H48) MaestroR Local Control } Gray Brass Gray Blue - unused, Tighten1 Hot/Live Hot/Live Black Brass Silver To HomeWorks Dimmer Hub (HWI-H48) or next Wired MaestroR Local Control Blue - unused, Tighten1 Black Green Green 120 V~ 50 / 60 Hz Load 120 V~ 50 / 60 Hz Load Ground Ground Neutral Neutral Wiring Diagram 3 2 Multi-Location Installation without Neutral -6D and -10D with HQD-RD Remote Dimmer or Dimmer Remote Dimmer or Dimmer Dimmer or Remote Dimmer Violet To HomeWorks Dimmer Hub or next Wired } (HWI-H48) MaestroR Local Control Gray Brass Brass Blue Blue Brass Note: Dimmer can be installed in any location in the circuit. Blue Hot/Live Black 120 V~ 50 / 60 Hz Black Black Green Green Green Ground Ground Ground Load Neutral Wiring Diagram 4 2, 3 Multi-Location Installation with Neutral -6ND, -10ND, -5NE and -2ANF with HQD-RD; -8ANS with HQD-RS Remote Dimmer / Switch Remote Dimmer / Switch Dimmer / Switch/ Fan Speed Control3 Violet To HomeWorks Dimmer Hub or next Wired } (HWI-H48) MaestroR Local Control Gray Brass Blue Brass Blue Blue Silver Hot/Live Black Black 120 V~ 50 / 60 Hz Brass Black Green Green Green Ground Ground Ground Load Neutral 1 When using controls in single location installations, tighten the blue terminal. DO NOT connect the blue terminal to any other wiring or to ground. 2 Up to 9 HomeWorksR MaestroR Remote Dimmers / Switches may be connected to the HomeWorksR Wired MaestroR Dimmer / Switch / Fan Speed Controls. Total blue terminal wire length may be up to 250 ft (76 m). 3 Neutral wire Dimmers / Switches / Fan Speed Controls must be connected on the Load side of a multi-location installation. 8 | Lutron® 24/7 Technical Support—800.523.9466 product specifications 369700a 11.05.12 HomeWorks QS Wired Maestro Designer Local Controls ® ® Colors and Finishes Gloss Finishes Satin Finishes White WH Ivory IV Hot HT Merlot MR Plum PL Turquoise TQ Almond AL Light Almond LA Taupe TP Eggshell ES Biscuit BI Snow SW Gray GR Brown BR Palladium PD Midnight MN Sienna SI Terracotta TC Greenbriar GB Bluestone BG Mocha Stone MS Goldstone GS Desert Stone DS Stone ST Limestone LS Black BL • Due to printing limitations, colors and finishes shown cannot be guaranteed to perfectly match actual product colors. • Color chip keychains are available for more precise color matching: Gloss Finishes - DG-CK-1 Satin Finishes - SC-CK-1 Metal Finish (wallplate only) When using Stainless Steel wallplates, it is recommended to order the MaestroR Control in Midnight (MN). Stainless Steel SS 9 | Lutron® 24/7 Technical Support—800.523.9466
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Create Date : 2012:11:16 09:14:55-05:00 Keywords : HomeWorks, QS, Wired, Maestro, Designer, Local, Controls, 369700a, 369-700a, HWD-6D-XX, HWD-6ND-XX, HWD-10D-XX, HWD-10ND-XX, HWD05NE-XX, HWD-8ANS-XX, HWD-2ANF-XX, HQD-RD-XX, HQD-RS-XX, RK-D-XX, RK-S-XX, RK-AD-XX, RK-AS-XX, RK-F-XX Modify Date : 2013:11:06 14:01:07-05:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2013:11:06 14:01:07-05:00 Producer : Acrobat Distiller 10.0.0 (Windows) Format : application/pdf Title : HomeWorks QS Wired Maestro Designer Local Controls Spec Sheet Part #369700a Creator : Description : HomeWorks QS Wired Maestro Designer Local Controls Subject : HomeWorks, QS, Wired, Maestro, Designer, Local, Controls, 369700a, 369-700a, HWD-6D-XX, HWD-6ND-XX, HWD-10D-XX, HWD-10ND-XX, HWD05NE-XX, HWD-8ANS-XX, HWD-2ANF-XX, HQD-RD-XX, HQD-RS-XX, RK-D-XX, RK-S-XX, RK-AD-XX, RK-AS-XX, RK-F-XX Document ID : uuid:9cda17e3-556e-4678-af0c-af2b13736554 Instance ID : uuid:d019bfcd-f5cf-44d3-9907-1062846547a0 Page Count : 9EXIF Metadata provided by EXIF.tools