HomeWorks QS Wired Maestro Designer Local Controls Spec Sheet Part #369700a 122644 Catalog

122639-Catalog 1 122639-Catalog_1 122639-Catalog_1 Batch9 unilog cesco-content

122640-Catalog 1 122640-Catalog_1 122640-Catalog_1 Batch9 unilog cesco-content

: Pdf 122644-Catalog 122644-Catalog Batch9 unilog

Open the PDF directly: View PDF .
Page Count: 9

1 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

HomeWorks® QS Wired Maestro® local controls

function much like standard dimmers and switches,

but can be controlled as part of a lighting control

system. Local lighting controls are useful in locations

where single circuits of lighting need to be dimmed

or switched. Local fan speed controls are useful in

locations where control of a single ceiling paddle fan is

needed.

HomeWorks® QS Wired

Maestro® dimmers

incorporate advanced features such as fade on / fade

off, delayed long fade to off, and rapid full on.

HomeWorks® QS Wired

Maestro® local controls

include a Front Accessible Service Switch (FASSTM)

for safe lamp replacement. HomeWorks® QS Wired

Maestro® local controls install in single-pole or multi-

location applications. Remote dimmers / switches are

available for multi-location control.

Use Lutron® Designer (Claro® or Satin Colors®)

wallplates or designer-style wallplates from other

manufacturers. Wallplates are sold separately. Lutron®

Claro® and Satin Colors® wallplates snap on with no

visible means of attachment. HomeWorks® QS Wired

Maestro® local controls support color change kits.

Model Numbers

Dimmers

Incandescent/Magnetic Low-voltage

HWD-6D-XX* 600 W/600 VA Dimmer

HWD-6ND-XX* 600 W/600 VA Dimmer

HWD-10D-XX* 1000 W/1000 VA Dimmer

HWD-10ND-XX* 1000 W/1000 VA Dimmer

Electronic Low-voltage

HWD-5NE-XX* 500 W Neutral Dimmer

Switches

HWD-8ANS-XX* 8 A Lighting, 5.8 A Motor

Neutral Electronic Switch

Fan Speed Control

Single ceiling paddle fan only (120 V~)

HWD-2ANF-XX*

2 A Neutral Fan Speed

Control

Remotes (for multi-location installations)

HQD-RD-XX* Remote Dimmer (120 V~)

HQD-RS-XX* Remote Switch (120 V~)

Color Change Kits

RK-D-XX* Dimmers (-6D, -6ND,

-10D, -10ND)

RK-S-XX* Switches (-8ANS )

RK-AD-XX* Remote Dimmer (-RD)

RK-AS-XX* Remote Switch (-RS)

RK-F-XX* Fan Speed Control (-2ANF)

Note: No color change kit is available for -5NE

Switch

Dimmer

Remote

Dimmer

Fan Speed

Remote

Switch

* “XX” in the model number represents color/fi nish code.

See Colors and Finishes at end of document.

2 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Specifi cations

Model Numbers Dimmer:

HWD-6D-XX, HWD-6ND-XX, HWD-10D-XX, HWD-10ND-XX,

HWD-5NE-XX

Switch:

HWD-8ANS-XX

Fan Speed Control:

HWD-2ANF-XX

Remote:

HQD-RD-XX, HQD-RS-XX

Color Change Kits: RK-D-XX, RK-S-XX, RK-AD-XX, RK-AS-XX, RK-F-XX

Power 120 V~ 50 / 60 Hz

Typical Power

Consumption

Dimmer / Switch / Fan Speed Control: 0.75 W

Test conditions: load is off and nightlight mode is enabled.

Remote Dimmer / Switch: 0 W Test conditions: load is off.

Regulatory

Approvals

UL, CSA (all except -5NE), and NOM

Environment Ambient operating temperature: 32 °F to 104 °F (0 °C to 40 °C), 0% to 90%

humidity, non-condensing. Indoor use only.

Communications Wired Local Controls are wired to a HomeWorksR dimmer Hub (HWI-H48). One

pair twisted shielded 22 AWG to 18 AWG (0.5 mm2 to 1.0 mm2) IEC PELV/

NECR Class 2 wiring.

Capacity Each HomeWorksR Dimmer Hub (HWI-H48) is capable of directly controlling

up to 48 Wired MaestroR Local Controls. Up to 8 Wired Local Controls may be

wired to a single bus on the HWI-H48. Refer to IEC PELV/NECR Class 2.

ESD Protection Tested to withstand electrostatic discharge without damage or memory loss, in

accordance with IEC 61000-4-2.

Surge Protection Tested to withstand surge voltages without damage or loss of operation, in

accordance with IEEE C62.41-1991 Recommended Practice on Surge Voltages

in Low-Voltage AC Power Circuits.

Power Failure Power failure memory: should power be interrupted, the control will return to its

previous state when power is restored.

Mounting Requires a U.S. wallbox. 3 ½ in (89 mm) deep recommended, 2 ¼ in (57 mm)

deep minimum.

Wiring Uses conventional 3-way and 4-way wiring.

Warranty http://www.lutron.com/TechnicalDocumentLibrary/warranty.pdf

3 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Design Features

Dimmer

• On a single-tap, lights fade ON or OFF.

• On a double-tap, lights go to full ON.

• When ON, press and hold the tapswitch to

engage the delayed long fade to OFF.

• Light levels can be fi ne-tuned by pressing and

holding the dimming rocker until the desired

light level is reached.

• Two-wire dimmers available.

• Electronic low voltage dimmer available.

Switch

• On a single-tap, lights or motors turn ON or

OFF.

• Requires a neutral connection.

Fan Speed Control

• On a single-tap, fan turns ON or OFF.

• Fan speeds can be selected by pressing and

holding the fan speed control rocker until the

desired fan speed is reached.

• Controls one paddle type ceiling fan (Permanent

split-capacitor motor) up to 2 A. Not for use with

shaded-pole type motors (i.e. bath exhaust fans).

• Provides four (4) quiet speeds plus OFF.

• Not for use with fans that have integrated fan

speed and/or light control modules.

• Requires a neutral connection.

Dimensions

All dimensions are shown as in

(mm)

Front View Side View

5/16

(8) 1

1⁄8

(30)

4

11⁄16

(119)

2

15⁄16

(75)

5/16

(8) 1

3⁄8

(35)

-5NE only

Side View

5/16

(8) 1

11⁄16

(43)

-2ANF only

Side View

The HWD-5NE dimmer does not have terminals - it has wires.

Refer to the chart to the right for wire color equivalents when

viewing the wiring diagrams for the -5NE.

Terminal / Wire Color

Terminal Color -5NE Wire Color

Black Black

Brass Yellow

Silver White

Blue Blue

4 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Mounting and Parts Identifi cation

Wallbox

Control

Adapter

Mounting

Screws

Control

Mounting

Screws

Wallplate Adapter / Wallplate

purchased separately.

Wallplate

Wallplate

Adapter

Ganging and Derating

When combining controls in the same wallbox, derating is required. See Load Type and Capacity. No derating is required

for remote dimmers / switches / fan speed controls. -8ANS has fi ns that need to be removed for multigang installations.

Do not remove outside fi ns

on end of gang controls

-8ANS only:

Middle of gang control

has all fi ns removed

Each control has

inside fi ns removed

5 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Load Type and Capacity

Control Load Type Minimum Load Not

Ganged

End of

Gang

Middle of

Gang

Neutral

Connection

HWD-6D1

Incand. 50 W 600 W 500 W 400 W

NO

MLV250 W / VA 450 W /

600 VA

400 W /

500 VA

300 W /

400 VA

HWD-6ND1, 5

Incand. 10 W 600 W 500 W 400 W

YES

MLV210 W / VA 450 W /

600 VA

400 W /

500 VA

300 W /

400 VA

HWD-10D1

Incand. 50 W 1000 W 800 W 650 W

NO

MLV250 W / VA 800 W /

1000 VA

600 W /

800 VA

500 W /

650 VA

HWD-10ND1, 5

Incand. 10 W 1000 W 800 W 650 W

YES

MLV210 W / VA 800 W /

1000 VA

600 W /

800 VA

500 W /

650 VA

HWD-5NE ELV/Incand. 10 W 500 W 450 W 400 W YES

HWD-8ANS4, 7

Lighting 10 W 8 A 6.5 A 5 A

YES

Motor 0.083 A 1/4 HP

5.8 A 5.8 A 5 A

HWD-2ANF6Ceiling Fan 0.083 A 2 A 2 A 2 A YES

1 Dimmer Load Type: -6D, -6ND,-10D, and -10ND are designed for use with permanently installed incandescent, magnetic

low-voltage, or tungsten halogen only. Do not install dimmers to control receptacles or motor-operated appliances.

2 Low-Voltage Applications: Use -6D, -6ND, -10D and -10ND with magnetic (core and coil) low-voltage transformers only.

Not for use with electronic (solid-state) low-voltage transformers. To control electronic low-voltage transformers, use the

HWD-5NE control.

Operation of a low-voltage circuit with lamps inoperative or removed may result in transformer overheating and premature

failure. Lutron strongly recommends the following:

• Do not operate low-voltage circuits without operative lamps in place.

• Replace burned-out lamps as soon as possible.

• Use transformers that incorporate thermal protection or fused transformer primary windings to prevent transformer failure

due to overcurrent.

3 Switch Load Type: -8ANS is designed for use with all permanently installed lighting loads and with motor loads up to

1/4 HP (5.8 A)

4 Ceiling Fan Application (HWD-2ANF):

• Use to control one paddle-type ceiling fan (permanent split-capacitor).

• Use the ceiling fan’s pull chain to set its speed to the highest setting*.

• Do not use to control fans that use shaded-pole motors (i.e. bath exhaust fans).

• Do not use to control fans that have integrated fan speed controls (i.e. fans that have a remote control), unless the

integrated control is removed from the ceiling fan.

• Do not connect to any other motor-operated appliance or to any lighting load type.

• Do not use to control a fan lighting load (i.e. lighting kit).

*See Application Note # 217 “HomeWorksR MaestroR Controls Reference” for more information.

5 Can control the following power boosters/load interfaces: Hi-PowerR Boosters (HP-2, HP-4, HP-6), 0-10 Volt Interface

(GRX-TVI), Minimum Load Interface (LUT-LBX), Phase Adaptive Power Module (PHPM-PA), Switched Power Module

(PHPM-SW), and 3-Wire Flourescent Power Module (PHPM-3F).

6 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Operation

Status LEDs

(not on Remote Dimmers) Indicate

light level; glow softly as night light

when light is off

Dimming Rocker

Press to brighten

Press to dim

Tapswitch

Tap on / off

FASSTM

Front

Accessible

Service

Switch

Dimmer

Tapswitch

Tap on / off

FASSTM

Front

Accessible

Service

Switch

Switch

Status LED

(not on Remote Switches) Indicates

load status; glows softly as night

light when light is off

IMPORTANT NOTICE:

FASSTM - Front Accessible Service Switch

To replace bulb, remove power by pulling

the FASSTM switch out fully on all controlling

devices.

After replacing bulb(s), push the FASSTM

switch(es) back in fully to restore power to the

control(s).

Status LEDs

Indicate speed level; glow softly as

night light when fan is off

Speed Control Rocker

Press to increase speed

Press to decrease speed

Tapswitch

Tap on / off

FASSTM

Front

Accessible

Service

Switch

Fan Speed Control

HWD-5NE only

OFF ON

OR

7 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Wiring

Dimmer communications wiring may be in a

daisy chain, star, or t-tap confi guration. Each

home run on a bus may be up to 500 ft

(152 m) and may contain up to 8 devices.

The total length of wire on each bus (all home

runs) may be up to 1000 ft (305 m). Up to 48

HomeWorksR Wired MaestroR Local Controls

may be wired to the HomeWorksR Dimmer

Hub (HWI-H48). Up to four HWI-H48 Dimmer

Hubs may be placed on each processor link

confi gured as an H48 link in the HomeWorksR

software.

IEC PELV/NECR Class

2 wiring to HomeWorks

Dimmer Hub or other Wired

MaestroR devices

Dimmer Side View

Butt Splices

Drywall

Wall Box

Dimmer Backcover

IEC PELV/NECR Class 2 Wire Type

One pair twisted shielded 22 AWG to 18 AWG

(0.5 mm2 to 1.0 mm2) IEC PELV/NECR Class 2

wiring.

HWI-H48 Dimmer Hub

One pair twisted shielded 22 AWG

to 18 AWG (0.5 mm2 to 1.0mm2) IEC

PELV/NECR Class 2 wiring.

Maximum 500 ft (152 m) per home

run, maximum 1000 ft (305 m) total

per bus (non-polarized).

Up to 8 devices

may be wired to

each bus on the

H48.

VioletGrayVioletGrayVioletGray

8 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Single Location Installation without Neutral1

-6D and -10D

Single Location Installation with Neutral1

-6ND, -10ND, -5NE, -2ANF and -8ANS

Brass

Black

Blue - unused, Tighten1

Green

Ground

Hot/Live

Neutral

120 V~

50 / 60 Hz

Brass

Silver

Black

Green

Ground

Hot/Live

Neutral

Load

Multi-Location Installation without Neutral2

-6D and -10D with HQD-RD

Brass

Black

Blue

Green

Ground

Dimmer or

Remote Dimmer

Brass

Black

Blue

Green

Ground

Brass

Black

Blue

Green

Ground

Hot/Live

Neutral

Load

Load

Note: Dimmer can be installed

in any location in the circuit.

Wiring Diagrams

Dimmer/Switch

Remote Dimmer

or Dimmer

Remote Dimmer

or Dimmer

Wiring Diagram 1 Wiring Diagram 2

Wiring Diagram 3

120 V~

50 / 60 Hz

120 V~

50 / 60 Hz

Dimmer / Switch /

Fan Speed Control

Multi-Location Installation with Neutral2, 3

-6ND, -10ND, -5NE and -2ANF with HQD-RD; -8ANS with HQD-RS

Brass

Silver

Black

Blue

Green

Ground

Load

Brass

Black

Blue

Green

Ground

Remote Dimmer / Switch

Brass

Black

Blue

Green

Ground

Hot/Live

Neutral

Remote Dimmer / Switch

Wiring Diagram 4

120 V~

50 / 60 Hz

Dimmer / Switch/

Fan Speed Control3

Violet

Gray

To HomeWorks Dimmer Hub

(HWI-H48) or next Wired

MaestroR Local Control

Blue - unused, Tighten1

Violet

Gray

Violet

Gray

Violet

Gray

1 When using controls in single location installations, tighten the blue terminal. DO NOT connect the blue terminal to any other wiring or to ground.

2 Up to 9 HomeWorksR MaestroR Remote Dimmers / Switches may be connected to the HomeWorksR Wired MaestroR Dimmer / Switch / Fan Speed Controls. Total

blue terminal wire length may be up to 250 ft (76 m).

3 Neutral wire Dimmers / Switches / Fan Speed Controls must be connected on the Load side of a multi-location installation.

}}

}

}

To HomeWorks Dimmer Hub

(HWI-H48) or next Wired

MaestroR Local Control

To HomeWorks Dimmer Hub

(HWI-H48) or next Wired

MaestroR Local Control

To HomeWorks Dimmer Hub

(HWI-H48) or next Wired

MaestroR Local Control

9 | Lutron®24/7 Technical Support—800.523.9466

product specifi cations 11.05.12

369700a

HomeWorks® QS Wired Maestro® Designer Local Controls

Colors and Finishes

Gloss Finishes Satin Finishes

Metal Finish (wallplate only)

Stainless

Steel SS

Taupe

TP

Turquoise

TQ

Plum

PL

Merlot

MR

Terracotta

TC

Sienna

SI

Midnight

MN

Hot

HT

Desert Stone

DS

Eggshell

ES

Biscuit

BI

Snow

SW

Palladium

PD

Greenbriar

GB

Bluestone

BG

Mocha

Stone

MS

Goldstone

GS

Stone

ST

Limestone

LS

White

WH

Ivory

IV

Almond

AL

Light

Almond

LA

Gray

GR

Brown

BR

Black

BL

• Due to printing limitations,

colors and fi nishes shown

cannot be guaranteed

to perfectly match actual

product colors.

• Color chip keychains are

available for more precise

color matching:

Gloss Finishes - DG-CK-1

Satin Finishes - SC-CK-1

When using Stainless Steel wallplates,

it is recommended to order the

MaestroR Control in Midnight (MN).