3119 Lx Belden 8471 Cable Cutsheet

: Pdf 3119 Lx Belden 8471 Cable Cutsheet 3119_lx_belden_8471_cable_cutsheet spec products hba

Open the PDF directly: View PDF .
Page Count: 2

BELDEN 

PVC Jcket

Unsheilded

Twisted Pir #Tinned Cpper Cnductrs PVC Insul

tin

LX SYSTEM NETWORK CABLE REQUIREMENTS

Hubbell Controls' LX Lighting Control System requires the use of Belden #8471 cable for Riser Rated applications OR Windy City Wire

#104500 for Plenum Rated applications. These are the ONLY cables that can be used for network wiring with the LX System.

The use of substitute cables based on similar physical characteristics is not allowed and will VOID any warranty for the LX system or any

LX component connected to the substitute cable.

Riser Rated Belden 8471 Cable

LX SERIES NETWORKED LIGHTING CONTROLS

PROJECT INFORMATION

Project Name

Catalog No. Date

Hubbell Controls' LX network cable is used to interconnect LX Panels, LX Devices

and LX Accessories for a complete communications network. All devices that

communicate on the LX Network are connected with the same type of twisted

pair cable. Both power and data are carried over the same two wires. The LX

System is wired as a topology-free, polarity-insensitive network. Hubbell Controls

supplied LX Network Cables assure proper network communications and should

be specied and installed on all LX System projects.

PRODUCT FEATURES

• Interconnects LX Lighting Control Panels and LX network devices

• Cable carries both power and data in a single twisted pair

• Belden #8471 - twisted pair #16 tinned copper

• Single cable type connects to all types of LX network devices

• Echelon Guideline Compliant for LON networks

• Available in 100 ft and 500 ft reels

• Riser Rated

• Connects to terminal blocks or with twist on connectors

• UL and cUL Listed

• One-year limited warranty

INSTALLATION NOTES

1. DO NOT exceed 1500 feet of cable OR connect more than 56 devices per network segment.

2. Each network segment using LP style devices requires an LXLPM2 Link Power Module for device power. Each additional segment requires

an additional LXLPM2 Link Power Module and an LXRRM Repeater for data transmission between segments.

3. Each network segment existing of panels only or that use FT style devices only require termination with LXTERMINATOR instead of LXLPM2 Link Power Module.

4. Run cable and connect network with the shortest distances possible. The most ecient network is wired similar to branch circuit outlets.

5. When using twist-on wire connectors with network cable use no more than three wires per connector.

6. The use of T-taps to minimize cable length is encouraged. Daisy chain topology is allowed, but most often increases overall cable length.

7. DO NOT homerun all devices individually, or leave spare cable at ceiling mounted devices. If devices need to be relocated, cables can be extended with

twist-on wire connectors.

8. DO NOT mix plenum and NON-plenum cables on the same segment.

9. Keep 12” minimum from line voltage, do nut run in the same raceway with line voltage.

*All sales are nal, no returns are allowed.

MODEL

LX8471CBL100* LX Cable Belden 8471 Riser Rated 100 ft Reel

LX8471CBL500* LX Cable Belden 8471 Riser Rated 500 ft Reel

General Specications

Description 1 pair - 16 AWG stranded tinned copper conductors,

PVC Insulation, unshielded twisted pair (UTP), PVC jacket

Shielding Unshielded

Overall Nominal Diameter 0.274 inches

Plenum Rating Not Plenum Rated

Operating Temperature Range -20°C to +80°C (Indoor use only)

Maximum Pulling Tension 61 lbs

Minimum Bend Radius 5.1 inches

Color Pair Color - Black/White, Outer Jacket - Gray

Certications NEC (UL) CMG, CEC/C (UL) CMG,

Flame Test UL Flame Test – UL1685 FT4 Loading,

C (UL) Flame Test FT4

Warranty One-year limited

Ordering Information

9601 Dessau Road | Building One | Austin, Texas 78754 | 512-450-1100 | 512-450-1215 fax | www. hubbell-automation.com 3119A 2.4.2016