Instruction_Sheet Installation Directions

323263-Installation 323263-Installation 323263-Installation 751928 Batch4 unilog cesco-content

: Pdf 323263-Installationsheet 323263-InstallationSheet 751928 Batch4 unilog

Open the PDF directly: View PDF .
Page Count: 1

Operation:

All controls are designed to turn-on within a

range of 1-5 foot candles and turn-off within a

range of 3-15 foot candles.

The FT and SFT controls have a movable

shutter to provide for turn-on/turn-off settings.

Test:

To test all controls simply cover photocell to

simulate darkness and wait approximately 5

minutes for control to respond.

FA - To prevent water entry into photocontrol,

always install photocontrol with wire side down

and a drip loop on the lead wires.

Installation Instructions:

1. Turn off all power at fuse or breaker box.

2. Ensure that the supply voltage matches the

photocontrol voltage rating (see table)

3. Wire control as indicated in Figure 1.

Installation must be in compliance with NFPA

National Electrical Code which requires both

sides of an ungrounded single phase or

multi-phase line be broken (article 410-48)

for lighting loads.

4. The control should be mounted such that the

“photocell” faces away from artificial light

sources. It must not be illuminated by the

lamp it controls or it will cycle on & off at

night.

5. Control should be mounted with wires facing

down to prevent moisture ingress.

6. Once power is restored lamp will come on.

7. Allow up to 5 minutes for lamp to turn off for

daytime operation.

Installation Instructions:

1. Turn off all power at fuse or breaker box.

2. Ensure that the supply voltage matches the photocontrol voltage rating (see table)

3. Wire socket as indicated in wiring diagrams shown.

4. The socket should be mounted such that the “photocell” faces away from artificial light

sources. It must not be illuminated by the lamp it controls or it will cycle on & off at night.

5. Installation must be in compliance with NFPA National Electrical Code which requires both sides

of an ungrounded single phase or multi-phase line be broken (article 410-48) for lighting loads.

6. To install the control, firmly place it into the socket and twist it clockwise until it locks into place.

7. To confirm proper control installation, during daylight hours, cover the window completely to

simulate darkness. The control should switch the load on within 1-2 minutes.

*Note: NS47671, NS47673 socket shall ne mounted directly through standard 1/2” NPT or

1/2” knockout, for NS47671, NS47673 a 1/4” NPT or 1/4” knockout, connection to junction

box must be watertight through the use of thread compound or suitable weatherproof washer.

Operation:

All controls are designed to turn-on within a range of 1-5 foot candles and turn-off

within a range of 3-15 foot candles.

OUTDOOR LIGHTING CONTROLS

FROM FP OLC

54 Commercial Street

Raynham, MA 02767 USA

508-884-9732

www.fisherpierceolc.com

H3007

Installation

Mounting:

Figure1

KNURLED NUT

MODEL

FA - 105

FA - 1068

RED

BLACK

WHITE

AC SUPPLY

NEUTRAL

LAMP

(SEE TABLE)

SINGLE PHASE

GROUNDED LINE

GASKET

N L1

BW

W

UNGROUNDED SINGLE PHASE

OR MULTI PHASE LINE

DPST

RELAY

FT15, SFT15 120 2000W 1000VA

FT168, FFST168 208-277 2000W 1000VA

FT19**, SFT19** 480 2000W 1000VA

FL115 120 2000W 1000VA

FA105, FA105P.W 120 2000W 1000VA

FA1068, FA1068P.W 208-277 2000W 1000VA

Model Line Load Rating

Voltage Tungsten Ballast*

** Not UL Listed or CSA Certified

*HID Ballast Rating

Control Model Line Voltage Load Rating-HID

N7762E 120 1800VA

N7772E 240 1800VA

N7790B 105-285 1800VA

N7792E 105-285 1800VA

N7793 350 1800VA

N7794 480 1800VA

FP240 240 1800VA

FP240H 240 1800VA

Control Model Line Voltage Load Rating-HID

FP120 120 1800VA

FP208-277 208-277 1800VA

FP480* 420-530 1800VA

N7760 120 1800VA

N7841* 120 1800VA

N7842* 208-277 1800VA

MULTI-RELAYS

N251A/N252A* 120 3000VA

N261/N262* 120 3000VA

N271/N272* 120 3000VA

NS476XX UP to 480 15 Amps Max.

NAT9021 Up to 480 15 Amps Max.

** Not UL Listed or CSA Certified

*HID Ballast Rating

FA Series controls are designed for mount-

ing in any UL approved junction box. The

control is provided with a neoprene gasket

and one knurled nut for mounting in a wall

plate with 11/16” center opening. The FA

series with post collar is provided with a self

tapping screw for grounding the post collar.

Drill a 1/8” diameter hole into existing post

through hole in adapter and install self-tapping

ground screw. The FT, SFT & FL series are

designed to mount in a standard UL approved

junction box.

Photocontrol can be mounted directly

through standard 1/2” NPT or 1/2” knockout.

Connection to junction box must be watertight

through the use of thread compound or

suitable weatherproof washer. SFT and FL

series are provided with an elbow to allow the

control’s “photocell” to be directed away from

ambient light sources.

TYPICAL WIRING DIAGRAMS

GROUND

SCREW

FA105P

FA1068P

FA105W

FA1068W

FT15

FT168

FT19

ADJUSTMENT

SHUTTER

SFT15

SFT168

SFT19

FL115

B

R

W

N L1 DPST

RELAY

SINGLE PHASE

GROUNDED LINE

UNGROUNDED SINGLE PHASE

OR MULTI PHASE LINE

SINGLE PHASE

GROUNDED SUPPLIES AND LOADS

N L1

LINE (BLACK)

LOAD (RED)

NEUT. (WHITE)

LOAD

NFP AND N6690/N7700 PHOTOCONTROLS

Cupola

7840 SERIES

STANDARD NS47671

NS47673

N251/N252A

NS47681

NAT9021

N271/N272 SERIES

N281/N282 SERIES

SEE NOTE

54 Commercial Street

Raynham, MA 02767

P: 508-821-1597, FAX: 508-822-0593

www.fpolc.com