6 1110XI_Copy Of 455221 Product Data Sheet

: Pdf 455221 Product Data Sheet 455221 Product Data Sheet Forms

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

6-1110XI Series

SPEEDHIDE®
Architectural Coatings

SPEEDHIDE Interior Wall and Trim Semi-Gloss Oil

GENERAL DESCRIPTION
Our best professional interior semi-gloss alkyd formulated to
meet the performance requirements of professional applicators.
SPEEDHIDE Interior Semi-Gloss Oil provides excellent hiding,
touchup, stain removal and scrubbability properties. SPEEDHIDE
Interior Semi-Gloss Oil is an alkyd with excellent flow and leveling to yield a smooth, even appearance on interior walls and trim
surfaces. Recommended for interior use on properly prepared
and primed or previously painted drywall, plaster, masonry, wood,
and metal surfaces.

RECOMMENDED SUBSTRATES
Aluminum
Concrete
Ferrous Metal
Galvanized Steel

Gypsum Wallboard-Drywall
Masonry
Plaster
Wood

CONFORMANCE STANDARDS
VOC compliant - lower than Federal AIM
Meets MPI® Category #47, Interior Alkyd Semi-Gloss, Gloss
Level 5

TINTING AND BASE INFORMATION
Refer to the appropriate color formula book, automatic tinting
equipment, and or computer color matching system for color formulas
and tinting instructions.
6-1110XI
6-1160XI
6-1300XI

White and Pastel Base
Midtone Base*
Neutral Base*

*Must be tinted before use.
Some colors, drastic color changes, or porous substrates may require
more than one coat to achieve a uniform finish.

PRODUCT DATA
PRODUCT TYPE:
SHEEN:
VOLUME SOLIDS*:
WEIGHT SOLIDS*:
VOC*:

Alkyd
Semi-Gloss: 50 to 70 (60º Gloss Meter)
52% +/- 2%
70% +/- 2%
374 g/L (3.1 lbs./gal.)

APPLICATION INFORMATION

WEIGHT/GALLON*:
10.4 lbs. (4.7 kg) +/- 0.2 lbs. (91 g)
*Product data calculated on product 6-1110XI.
COVERAGE: Approximately 400 sq. ft./gal. (37.2 sq. m/3.78L) per
U.S. Gallon (3.78L) on smooth, nonporous surfaces.
Wet Film Thickness:
4 mils
Wet Microns:
102
Dry Film Thickness:
2.1 mils
Dry Microns:
53
Application Equipment: Apply with a high quality brush, roller, Coverage figures do not include loss due to surface irregularities and
paint pad, or by spray equipment. Where necessary, apply a sec- porosity or material loss due to application method or mixing.
ond coat.
DRYING TIME: Dry time @ 77ºF (25ºC); 50% relative humidity.
To Touch:
5 hours
Airless Spray: Pressure 2000 psi, tip 0.017” - 0.021”
To
Recoat:
24 hours
Spray equipment must be handled with due care and in
To
Full
Cure:
7 to 14 days
accordance with manufacturer’s recommendation. High-pressure
injection of coatings into the skin by airless equipment may cause Drying times listed may vary depending on temperature, humidity, film
build, color, and air movement.
serious injury.
Stir thoroughly before and occasionally during use. When using
more than one can of the same color, intermix to ensure color
uniformity. USE WITH ADEQUATE VENTILATION. KEEP OUT
OF REACH OF CHILDREN. Read all label and Material Safety
Data Sheet (MSDS) information prior to use. MSDS are available
through our website or by calling 1-800-441-9695.

Explosion-proof equipment must be used when coating with these CLEANUP: High quality paint thinner
materials in confined areas. Keep containers closed and away DANGER: Rags, steel wool or waste soaked with this product may
spontaneously catch fire if improperly discarded. Immediately after
from heat, sparks, and flames when not in use.
use, place rags, steel wool or waste in a sealed water-filled metal
container. Refer to www.ppgpittsburghpaints.com, Spontaneous
Brush: High quality natural bristle brush
Combustion Advisory for additional information.
Roller: 3/16” - 3/8” nap roller cover
Thinning: Do not thin.
Permissible temperatures during
Material:
50 to 90ºF
Ambient:
50 to 90ºF
Substrate:
50 to 90ºF

application:
10 to 32ºC
10 to 32ºC
10 to 32ºC

DISPOSAL: Contact your local environmental regulatory agency for
guidance on disposal of unused product. Do not pour down a drain or
storm sewer.
FLASH POINT:

116ºF (46.7ºC)

FEATURES / BENEFITS
Features
Excellent adhesion
Excellent block resistance
Excellent flow and leveling
Alkyd hardness and durability
Good color and gloss retention
Excellent scrubbability
Good hiding power and coverage
Meets MPI Category #47, Interior Alkyd
Semi-Gloss, Gloss Level 5

Benefits
Sticks to difficult substrates
Tack free film/ideal for doors, doorframes, and windowsills
Less brush marks on the paint film/better coverage on trim
Resists chipping providing long lasting beauty
Looks like new longer
Withstands repeated cleaning requirements
Hides surface imperfections
Meets strict performance and aesthetic requirements
A3.66

SPEEDHIDE®

6-1110XI Series

Architectural Coatings

SPEEDHIDE Interior Wall and Trim Semi-Gloss Oil

GENERAL SURFACE PREPARATION
Surfaces to be coated must be dry, clean, sound, and free from all contamination including loose and peeling paint, dirt, grease, oil, wax,
concrete curing agents and bond breakers, chalk, efflorescence, mildew, rust, product fines, and dust. Remove loose paint, chalk, and
efflorescence by wire brushing, scraping, sanding, and/or pressure washing. Putty all nail holes and caulk all cracks and open seams. Sand
all glossy, rough, and patched surfaces. Feather back all rough edges to sound surface by sanding. Prime all bare and porous substrates
with an appropriate primer.
WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST
OR FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a properly fitted NIOSH-approved respirator and prevent skin contact to control lead exposure. Clean up
carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the USEPA
National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. In Canada contact a regional Health Canada office.
Follow these instructions to control exposure to other hazardous substances that may be released during surface preparation.
ALUMINUM: This substrate may present potential adhesion problems. Any coating applied directly to aluminum should be spot applied,
allowed to cure overnight, and then evaluated for adhesion. If adhesion is good, the application may proceed.
CONCRETE and MASONRY: New concrete should cure for at least 30 days and preferably 90 days prior to priming and painting. The pH
of the substrate must be less than 10 before priming with an alkali resistant primer.
FERROUS METAL: The surface must be cleaned thoroughly to remove any dust, rust, and surface contaminants, and then primed.
GALVANIZED STEEL: Caution must be used when selecting coatings for use on all galvanized metal surfaces. These substrates may have
a factory-applied stabilizer, which is used to prevent white rusting during storage and shipping. Such stabilizers must be removed by either
brush blasting, sanding or chemical treatment prior to priming with a primer approved for galvanized steel.
GYPSUM WALLBOARD-DRYWALL: Nails or screws should be countersunk, and they along with any indentations should be mudded flush
with the surface, sanded smooth and cleaned to remove any dust, then prime prior to painting the substrate.
PLASTER: Plaster, hardcoat, skim coat, or other alkaline surfaces should be allowed to cure for at least 30 days prior to priming with an
alkali resistant primer.
WOOD: Unpainted wood or wood in poor condition should be sanded smooth, wiped clean, then primed. Any knots or resinous areas must
be primed before painting. Countersink all nails, putty flush with surface, then prime.

LIMITATIONS OF USE

RECOMMENDED PRIMERS
Aluminum
Concrete
Ferrous Metal
Galvanized Steel
Gypsum Wallboard-Drywall
Masonry
Plaster
Wood

6-204, 17-921
4-603, 17-921
6-208, 90-712, 90-912
6-209, 17-921
6-2, 6-4, 9-900, 12-900
4-603, 17-921
4-603, 17-921
6-9, 17-921, 12-900

Apply only when air, surface and product temperatures are between
50ºF (10ºC) and 90ºF (32ºC).
Not recommended for use on floors.
For exterior use on doors, trim, and other small areas of wood or
metal surfaces. Not for exterior use on large expanses of wood.
Important: All oil based alkyd products change color with age. The
yellow discoloration is most visible in whites and light colors. PPG
latex products are recommended when yellowing is a concern.

PACKAGING
1-Gallon (3.78L)
5-Gallon (18.9 L)
Not all products available in all sizes.
The PPG logo is a registered trademark of PPG Industries Ohio, Inc. SPEEDHIDE is a registered trademark of PPG Architectural Finishes, Inc. The Master Painters Institute
and MPI are registered trademarks of Master Painters Institute, Inc.
PPG Architectural Finishes, Inc. believes the technical data presented is currently accurate: however, no guarantee of accuracy, comprehensiveness, or performance is given or
implied. Improvements in coatings technology may cause future technical data to vary from what is in this bulletin. For complete, up-to-date technical information, visit our web
site or call 1-800-441-9695.
PPG Industries, Inc.
Architectural Coatings
One PPG Place
Pittsburgh, PA 15272
www.ppgpro.com

Technical Services
1-800-441-9695
1-888-807-5123 fax

Architect/Specifier
1-888-PPG-IDEA

PPG Canada, Inc.
Architectural Coatings
4 Kenview Blvd
Brampton, ON L6T 5E4

A3.66 4/2013
(Supersedes 9/2012)



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Format                          : application/pdf
Creator                         : car6622
Title                           : 6-1110XI_Copy of Layout 1
Create Date                     : 2013:04:22 13:40:49-04:00
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2018:06:08 15:02:30-04:00
Metadata Date                   : 2018:06:08 15:02:30-04:00
Producer                        : GPL Ghostscript 8.64
Document ID                     : uuid:35304953-d1f7-45f3-8286-cc8854269fb6
Instance ID                     : uuid:229cb7d5-9e03-49ed-b827-2e5beee74850
Page Count                      : 2
Author                          : car6622

EXIF Metadata provided by EXIF.tools