RTTE TCF Form 501682 CE Report Linktek

: Pdf 501682 Ce Report Linktek 501682_CE__Report--Linktek CertsReports 501682 ProductFiles

Open the PDF directly: View PDF .
Page Count: 146

Download
Open PDF In Browser	View PDF

APPLICATION FORM
We hereby order examination by Nemko as specified below. When the order is received, Nemko will provide an Order Confirmation
which, together with the signed Application Form, will constitue a binding agreement between the applicant and NEMKO. The
appropriate conditions are described overleaf.
Name and address
APPLICANT
Our reference./ contact person: Mr. Jason Chang
Cameo Communications, Inc
Possible other invoice reference:
No. 42, Min Chuan East Road, Section 6, Taipei 114,
TRAINING RESEARCH CO., LTD.
Taiwan
Phone: 886-2-2693-5155 ext.32
Fax/E-mail: 886-2-2693-4440 /
jack@trclab.com.tw
MANUFACTURER
(if different from
the applicant)

FACTORY/
PROD. SITE

Name and address

Cameo Communications, Inc
6F, NO. 22, Chung Shin Rd., Hsi-Chih, Taipei 221, Taiwan
Name and address

(if different from
the manufacturer)

PRODUCT
CATEGORY
MARKING ON
THE PRODUCT

802.11g Wireless PCI Adapter
Model/ type : WLG-1202, WNC-0300, LWS5410P, NWP-0108G, ALL0281A

Data:
Other specification: 802.11g Wireless PCI Adapter

THE ORDER
COMPRISES

SUBMITTED/
ENCLOSED

Name/ trade mark/logo *) CAMEO, Level One, LG, Etherwan, Allnet GmbH
x New order
¨ Repeated examination, please indicate previous Nemko Order No.:

¨ Complete Nemko product certificate *)
¨ Nordic Certification Service *) for: ¨ Denmark
¨ Finland
¨
¨ Testing for European certification (CCA), relevant countries: *)
¨ Testing for international certification (CB) , relevant countries: *)
¨ Statement of conformity with standard for one product sample *)
¨ Test report according to the following standards/specifications:
¨ Attestation of conformity with: ¨ The EMC-Directive
¨
x Other: *) Conformity assessment for letter of opinion R&TTE Directive
¨

¨

Test sample(s)

Sweden

x Drawing(s)
x EMC test report

¨

List of applicant(s)/contact(s) in secondary countries for Nordic Certification Service *)

Test sample(s)
after examination::

¨

Collected by applicant 1)

Completed Questionnaire
on Production surveillance *)

¨

Power of Attorny *)
Certificate desired in:
Delivery of result:

¨

¨

¨

Enclosed

¨

English

By mail

Submitted previously

¨
¨

¨

Submitted previously

¨ Norwegian
Preliminary by fax *)

Test report(s)
from others
Certificate(s) from others
¨ Self declaration
(conformi
ty
with the EMC
Directive)

¨

To be discarded by Nemko

¨

Enclosed

Iceland *)

x

*)

x Other: See attached TCF
SPECIAL
INFORMATIO
N

¨

Other relevant Directives *)

x Declaration of Identity

Extra components

x Wiring/circuit diagram(s) x Part list
x User’s instruction
¨ Mounting instruction
¨

...................................

¨

Returned at
applicant’
s cost

Will be forwarded

¨

Will
be
forwarded
¨ Other *
By courier express service
*

Remarks:
We recognize and accept the technical, commercial and legal conditions described overleaf, as far as these are applicable to the specified
assignment.
The undersigned is authorized to sign on behalf of the applicant.

2005/4/27
Date
*) Confer separate Guidance

Cameo Communications, Inc (Jason Chang / Wireless Comm. R&D Dept. Manager)
Binding on the applicant
1) Will be discarded by Nemko if not collected or notice given within 4 weeks after dispatch of the Return
Notice. The same applies if not ticked in any of the boxes for “Test sample(s) after examination”.

APPLICATION FORM - R&TTE APPENDIX
We hereby order Notified Body assessment by Nemko as specified belo w. When the order is received, Nemko will provide an Order Confirmation, which
together with the signed Application Form, will constitue a binding agreement between the applicant and Nemko.

APPLICANT

Name and address

PRODUCT

Category

Model/type

802.11g Wireless PCI Adapter

WLG-1202, WNC-0300, LWS5410P, NWP-0108G, ALL0281A

Frequency range

Range

Harmonized

RADIO
TECHINCAL

TCAM

Cameo Communications, Inc
No. 42, Min Chuan East Road, Section 6, Taipei 114, Taiwan

2412 to 2472 MHz

YES

Channels

Number

Separation

Output power

13
5
802.11b: 93.33mW ; 802.11g: 94.62mW (e.i.r.p.)

Modulation

DBPSK / DQPSK / CCK / OFDM

Type of antenna

Dipole

Category

(if applicable)

USAGE
THE ORDER
COMPRISES

Intended use

Operating environment

Portability

RESIDENTIAL

PORTABLE

R&TTE Directive – Module Aa (Annex III) – Radio test suite assessment
(NB issues a radio test suite proposal)

R&TTE Directive – Module Aa+ (Annex IV) – TCF assessment
(NB issues an opinion based on examination of the technical construction file (TCF) presented by the applicant)

R&TTE Directive – Module H (Annex V) – Full quality assessment
(NB verifies the quality system and the requirements for periodic control of test suites)

Remarks:

OTHER

Similar applications have been submitted to other Notified Bodies (must be listed on separate letter)
Nemko is supposed to do assessments of the quality system
Nemko is supposed to do annual production surveillance

SUBMITTED
DOCUMENTS

Safety test report (3.1a)

Technical specifications

User documentation

MPE calculation (3.1a)

Principle diagrams

Service documentation

EMC test report (3.1b)

Block diagrams

ISO 9000 certificates

Radio test report (3.2)

Circuit diagrams

Quality manual

CEPT radio application

Part lists

Methods for periodic control

List of standards

Component lists

Declaration of Conformity

STANDARDS
APPLIED

Sample of the product

Art.3.1a

Art.3.1b

Art.3.2

EN60950-1: 2001

EN 301 489-1 V1.4.1
EN 301 489-17 V1.2.1

EN 300 328-2 V1.2.1

Art.3.3

REMARKS

This appendix supports the information given in the Nemko application form. The same conditions apply. The undersigned is authorized to sign on behalf of the applicant.

2005/4/27
Date

Cameo Communications, Inc
(Jason Chang / Wireless Comm. R&D Dept. Manager)
Binding on the applicant

Nemko's general terms of agreement for testing and certification of equipment

1.1

1.1.1

1.1.2

1.2

The terms of this agreement govern the relation between the party applying for
testing/evaluation and/or certification of equipment (the Applicant), the party
responsible for design, production and quality assurance of the equipment or
marks the equipment as its (the Manufacturer) and Nemko performing the
services.
If the order is to lead to certification, then part 1., 2. and 3. of these terms shall
apply. The Applicant to be the Manufa cturer or a physical or juridical person
appointed by the Manufacturer.
Should the Applicant not be identical with the Manufacturer in such cases,
the order shall be carried out only if the Manufacturer, on a form set by Nemko
(Power of Attorny), declares that he is aware of and agrees that the Applicant
gives Nemko the task of carrying out the certification of the equipment in
question and that he accepts the obligations that these terms impose on the
Manufacturer. (items 1.2, 3.2.1, 3.2.4, 3.2.6, 3.2.7, 3 .3, 3.4.2).
If the order is to lead to issuing of a test report or another document only
giving statement concerning the tested sample, part 1., 2. of these terms shall
apply. Nemko is carrying such orders regardless of who the Applicant is, and
shall in this connection solely cooperate with the Applicant concerned.
The general terms are as follows:
The Applicant is obliged to pay Nemko for the performing of the agreed order
in accordance with the at all times current Nemko prices. For certificates this
also includes payment of an annual licence fee for the right to use the
certificate and for the right to use Nemko's name or certification mark. The
Applicant is obliged to pay for for the work performed with the purpose of
issuing a certificate, even if such document cannot be issued, whether being
due to the tested sample, the Manufacturer or the Applicant.
Regarding orders which are to result in issuing of a certificate, Nemko may
permit that the obligation to pay totally or partly is transferred from the
Applicant to the Manufacturer, provided this is satisfactory documented
towards Nemko.
Payment to take place in accordance with invoices and their terms of payment.
Nemko may require payment in advance. I such case the balance will be settled
upon completion of the order. Other terms of delivery will be as described in
connection with confirmation for the individual order.

1.3

1.4

The Nemko staff is bound to observe professional secrecy, not disclosing any
confidential information received in connection with the order. According to
Norwegian law, the professional secrecy may be set aside in case of lawsuit in
Norwegian Court. Nemko is also obliged to ensure that other co-operating
bodies that might deal with the order, instruct their staff to observe the
equivalent professional secrecy.
Nemko's decision may be appealed to Nemko's Appeal Committee, which
deals with the appeal in accordance with Nemko's appeal procedure. An
appeal in writing must be received by Nemko within 3 weeks from the time the
Applicant has received Nemko's written decision.
Any dispute that might occur regarding these terms, one should primarily try
to resolve by negotiations between the parties. If this fail to succeed, the
dispute should be decided by the ordinary courts, unless the parties agree to
arbitration. Any dispute to be settled in accordance with Norwegian law.
Legal venue is City of Oslo Stipendiary Magistrate's Court.

3.1

GENERAL

3.1.1

Based on performed testing or other examination, Nemko certifies equipment found
to comply with current standard or other agreed specification, and which
otherwise is considered suitable for its purpose. Nemko also issues
documentation as a basis for certification in other countries in accordance with i.a.
Nordic EMKO agreement, European CCA agreement or international CB
agreement (primary orders). Correspondingly, Nemko issues national certificates,
based on documentation from other certification bodies according to the above
mentioned agreements (secondary orders).

3.1.2

As a basis for the application, the Applicant is to submit the material and
information found necessary by Nemko for issuing and maintainance of such a
certificate. Documentation in accordance with the EMKO-, CCA-, CB agreement or
equivalent, to be a basis for the certification by Nemko, must not exceed 3 years of
age.

3.1.3

Unless otherwise agreed upon, Nemko has the proprietary right to Nemko's own
original documents. These documents are filed by Nemko during their period of
validity, cfr. item 3.4.1.

3.2

FURTHER RIGHTS, RESPONSIBILITIES AND OBLIGATIONS

3.2.1

In connection with marketing, sales etc., the Manufacturer and the Applicant have
the right to inform that the products are certified by Nemko. The Manufacturer and
the Applicant are obliged to ensure that Nemko's name or certification mark are
affixed to the certified products in accordance with current instructions, and that
Nemko's name and certification mark are not misused.

3.2.2

Nemko's certificate, test report etc. does not exe mpt the Applicant, the
Manufacturer nor a third party for liability according to Norwegian or foreign
product liability legislation.

3.2.3

The certificate may be pleaded as documentation only for products that are
manufactured in total conformity with the certified design.

3.2.4

The Manufacturer is obliged to conform to the rules applying for Nemko's
production surveillance. If required by Nemko, representatives from Nemko or from
other bodies acting on Nemko's behalf, are given admittance to the production
sites, in order to ensure that the conditions associated with the certificates issued
by Nemko, are maintained. Nemko is entitled to invoice the Manufacturer for the
costs related to consumption of work hours, travel- and daily allowances, in
accordance with item 1 .2.

3.2.5

In cases required by Nemko, the Applicant shall, free of all costs to Nemko,
provide a sample of the certified product for re-examination in order to ensure that
it remains in conformity with the certified design. The Applicant is obliged to pay
for Nemko’s costs in connection with such re-examination.

3.2.6

Nemko to be notified by the Manufacturer with regard to complaints covering the
equipment and possibly affecting the certificate.

3.2.7

The Manufacturer and the Applicant are obliged to conform to Nemko's possible
directions, as a consequence of the above items 3.2.4 - 3.2.6.

3.3

CHANGES TO THE PRODUCT
The manufacturer shall notify Nemko in writing of any proposed product
alteration. Nemko is to evaluate whether the certificate may be maintained or
whether the equipment has to be re-certified, if necessary after repeated testing.

1.5

Nemko's Board has at any time the right to revise the present terms.
Alterations of the terms are only applicable for orders commenced 3 - three weeks after Nemko's Board having approved the alterations concerned.

1.6

The rights to a certificate devolve on the Manufacturer, provided that the
Applicant does not produce evidence that it is agreed with the Manufacturer
that such rights are to pass to the Applicant.
The rights to a test report or any other document concerning the tested sample
only, devolve on the Applicant.

3.4

DURATION, TERMINATION AND WITHDRAWAL

3.4.1

Rights and obligations according to these terms attaching to an issued certificate,
do no longer apply after expiry period of the certificate, i.e. maximum 10 years,
unless otherwise is stated in the certificate. (Not applicable to Ex-equipment).

1.7

Nemko has no liability for errors made in connection with the performance of
the order except for errors due to purpose or gross negligence on Nemko's
side. Nor has Nemko any liability for indirect losses, cfr. Norwegian Sale of
Goods Act § 67 (2).

3.4.2

1.8

The present terms are binding on the Applicant as from the moment he has
signed the Application form,and when appliable, for the Manufacturer when a
Power of Attorny as mentioned under item 1.1.1 is signed.

If production and/or marketing of certified equipment should terminate, and
obligations according to the present terms should be required terminated, the
Manufacturer or the Applicant must immediately give Nemko a written request to
be released from the obligations. If Nemko agrees to the release, the rights of the
persons or companies concerned according to the certificate simultaneously shall
no longer apply.

3.4.3

Nemko may withdraw the certificate if the Manufacturer or the Applicant do not
fulfil their obligations in accordance with the present terms. Notice of withdrawal
is to be sent in writing, stating the reason for the withdrawal and the appointed
time of conclusion. Withdrawal of a certificate will normally take effect between 1
and 6 months upon Nemko's dispatch of their notice of withdrawal. In case of
fundamental breach, the withdrawal may have immediate effect. If a certificate
should be withdrawn, each and every right in accordance with the certificate and
the present terms shall no longer apply, hereunder the right to use Nemko's name
and certification mark.

3.5

TRANSFER OF CERTIFICATE
The certificate may only be transferred when it is documented towards Nemko that
the present and future owner of the certificate agree to that. The product may,
however, be re-certified under a different company name, as long as documentation
is produced showing that the holder of the certificate permits this. Should the
Manufacturer in such cases approve a new Applicant, a new Power of Attorny as
mentiond under item 1.1.1 above must be submitted. Agreements made between the
former Applicant(s) and the Manufacturer is outside the concern of Nemko.

1.9

These terms are issued in an English and a Norwegian version. In case of
differencies in the wording, the Norwegian version shall apply and the
Norwegian version will supersede the English version.

2.

TESTING/EVALUATION

2.1

Nemko carries out testing/evaluation of equipment according to valid
standard or other agreed specification. Nemko reserves the right, in
exceptional cases, to subcontract parts of the testing to an other competent
laboratory.

2.2

As a basis for the testing, the Applicant is to submit, free of all costs to
Nemko, test sample(s), installation and user’s instruction, other technical
documentation, extra components etc. to the extent found necessary by Nemko
for the order in question.

2.3

Nemko undertakes no responsibility whatsoever for damages that might occur

necessary, the Applicant himself is to provide for insurance covering all
submitted material, cfr. item 2.2. Test samples not collected within 4 - four weeks from Nemko dispatching a Return Notice will be discarded. The same
applies if none of the boxes of the Application Form for "Test sample(s) after
examination" are ticked off.

3.6

For maintenance of the certificate, hereunder the use of Nemko's name or
certification mark on certified products and in connection with marketing and
sales, an annual fee per each certified type/model shall be paid, according to item
1.2. In case of termination or withdrawal of a certificate, the annual fee will not be
refunded.

R&TTE
Technical Construction File

Product description:
802.11g Wireless PCI Adapter

Applicant:
CAMEO COMMUNICATIONS, INC.

Manufacture:
CAMEO COMMUNICATIONS, INC.

Brand and Type/model number:
Brand Name

Model Name

Cameo

WLG-1202

Level One

WNC-0300

LG

LWS5410P

Etherwan

NWP-0108-G

Allnet GmbH

ALL0281A

Technical Construction file in accordance with R&TTE Annex IV
Under the provisions if Annex IV point 4 of the R&TTE directive 1999/5/EC of the European Parliament
and of the council of 9 March on Radio equipment and Telecommunications Terminal Equipment
(R&TTE directive) and the mutual recognition of their conformity,
We, the undersigned,
Company
Address, City
Country
Phone number
Fax number
E-mail

CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6, Taipei 114,
Taiwan
886-2-27908998
886-2-27909463
Jason_Chang@mail.cameo.com.tw

Have established a Technical Construction File as specified below to be presented to the Notified Body
for his opinion and to be kept available to the relevant national authorities of any Member State for
inspection purpose:
Item number
01
02

Technical Document description
Technical File in accordance with R&TTE directive Annex II point 4
Declaration of conformity to specific test suites described in R&TTE directive Annex III

For the following product:
Product Description / Supplementary Info
Manufacturer
Brand
Type

802.11g Wireless PCI Adapter
CAMEO COMMUNICATIONS, INC.
CAMEO, Level One, LG, Etherwan, Allnet GmbH
WLG-1202, WNC-0300, LWS5410P, NWP-0108G, ALL0281A

The Technical Construction File as specified above will be kept for a period ending at least 10 years
after the last product has been manufactured at the disposal of the relevant national authorities of any
Member State for inspection purpose,
Draw up in
Date

TAIWAN, R.O.C.
2005/4/27
CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6,
Taipei 114, Taiwan

Signature & company stamp

Jason Chang /
Wireless Comm. R&D Dept. Manager

Technical Construction file in accordance with R&TTE Annex II Point 4
Under the provisions if Annex II point 4 of the R&TTE directive 1999/5/EC of the European Parliament
and of the council of 9 March on Radio equipment and Telecommunications Terminal Equipment
(R&TTE directive) and the mutual recognition of their conformity,
We, the undersigned,
Company
Address, City
Country
Phone number
Fax number
E-mail

CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6, Taipei 114,
Taiwan
886-2-27908998
886-2-27909463
Jason_Chang@mail.cameo.com.tw

Have established a Technical Construction File as specified below to enable assessment of the product
conformity with the essential requirements of the R&TTE directive:
Item number
01
02a
02b
02c
02d
02e
02f
03a
03b
04
05
06
07

Technical Document description
Block diagram
Circuit diagram
PCB layout
Part list
Exterior photographs
Interior photographs
Label information
Technical description
User manual
R&TTE standard list
RF-EMC-LVD test report and corresponding annexes
Copy of the R&TTE Declaration of Conformity (DOC)
Product Quality Assurance documents

For the following product:
Product Description / Supplementary Info
Manufacturer
Brand
Type

802.11g Wireless PCI Adapter
CAMEO COMMUNICATIONS, INC.
CAMEO, Level One, LG, Etherwan, Allnet GmbH
WLG-1202, WNC-0300, LWS5410P, NWP-0108G, ALL0281A

The Technical File as specified above will be kept for a period ending at least 10 years after the last
product has been manufactured at the disposal of the relevant national authorities of any Member State
for inspection purpose,
Draw up in
Date

TAIWAN, R.O.C.
2005/4/27
CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6,
Taipei 114, Taiwan

Signature & company stamp

Jason Chang /
Wireless Comm. R&D Dept. Manager

Block Diagram

Block Diagram
32K Bit
EEPROM

PNP
3.3v

1.8V

PCI Interface

VREG_OUT

280mA

509mW

OPB
( Epicom )
PA2409

BPF

AR2414A-00

PDET

BPF

WAKE
ON
LAN

40MHZ
XTAL

Coupler

LED

XLNA
(SGA-8343)

SPDT
(NJG1600
KB2)

LPF

ANT
(SMA)

Circuit Diagram

5

4

3

2

1

3

SOT-23

5V_CON

1

3.3V_CON

3.3V_CON

D

2

EEPROM

Q1
NC,1PS301
SOT-23

3.3V

R1

PCI_PAR
AD15
AD13
AD11
AD9
PCI_CBE0_L
AD6
AD4

B

AD2
AD0

AD17
PCI_CBE2_L
PCI_IRDY_L
PCI_DEVSEL_L
PCI_PERR_L
PCI_SERR_L
PCI_CBE1_L
AD14
AD12
AD10

AD8
AD7
AD5
AD3
AD1

K1
L1
L2
R10
R6
P8
N9
R8
N10
P9
P10
R4
N1

PCI_INT_L
PCI_REQ_L
PCI_GNT_L
PCI_PERR_L
PCI_PAR
PCI_IRDY_L
PCI_TRDY_L
PCI_FRAME_L
PCI_STOP_L
PCI_SERR_L
PCI_DEVSEL_L
PCI_IDSEL
PCI_PME_L

8
10K

GREEN

4

R14

3

1
LED1

2

4
R

PCI_INT_L
PCI_REQ_L
PCI_GNT_L
PCI_PERR_L
PCI_PAR
PCI_IRDY_L
PCI_TRDY_L
PCI_FRAME_L
PCI_STOP_L
PCI_SERR_L
PCI_DEVSEL_L
IDSEL
PCI_PME_L

U0_CTS_L
U0_CLK
U0_SIN
EPRM_SCK
EPRM_SDA
ANTD
ANTB
ANTA

R15

PCI_CBE0_L
PCI_CBE1_L
PCI_CBE2_L
PCI_CBE3_L

C

TP1 TP2 TP3 TP4 TP5
=
=
=
=
=
=
=
=

1

P15
R11
R7
R3

5

KEEP CLOSE TOGETHER
RFDATAIN_3
RFDATAIN_2
RFDATAIN_1
RFDATAIN_0
RFDATAOUT
RFSHIFT
RFLOAD
RFRST_L

1

PCI_CBE0_L
PCI_CBE1_L
PCI_CBE2_L
PCI_CBE3_L

WC

SDA

ANTC 4
ANTB 4
ANTA 4

1

B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62

AD21
AD19

7

M24C32WMN6

AR2414A-00 EJTAG, GPIO, UART, EPRM, ANT

1

AD8
AD7
+3V3
AD5
AD3
GND
AD1
+5V(I/O)
#ACK64
+5V
+5V

PCI_CBE3_L
AD23

SCL

ANTC
ANTB
ANTA

1

#BE0/C
+3V3
AD6
AD4
GND
AD2
AD0
+5Vio
#REQ64
+5V
+5V

10K

A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62

A4
A5
B4
B5

6

U3

PUT TP12 ON TOP LAYER

TP6 TP7 TP8 TP9

TP10 TP11 TP12 TP13 TP14
U1C

R2

R3

A6
B6

POR_EN
POR_L

RX_FRAME
TX_FRAME

K2
F3

C6

F2D2EN

RX_CLEAR

R2

CLKOBS

E3

SLEEP

B3

K15

PLLBYPASS

K13

BT_ACTIVE

P14

RFTEST

1

PCI_STOP_L

ANTD
ANTC
ANTB
ANTA

1

PCI_TRDY_L

AD27
AD25

PCI_AD0
PCI_AD1
PCI_AD2
PCI_AD3
PCI_AD4
PCI_AD5
PCI_AD6
PCI_AD7
PCI_AD8
PCI_AD9
PCI_AD10
PCI_AD11
PCI_AD12
PCI_AD13
PCI_AD14
PCI_AD15
PCI_AD16
PCI_AD17
PCI_AD18
PCI_AD19
PCI_AD20
PCI_AD21
PCI_AD22
PCI_AD23
PCI_AD24
PCI_AD25
PCI_AD26
PCI_AD27
PCI_AD28
PCI_AD29
PCI_AD30
PCI_AD31

1

AD18
AD16
PCI_FRAME_L

PCI_REQ_L
AD31
AD29

L14
L15
L13
M15
M13
M14
N15
N14
R15
R14
P13
R13
P12
R12
P11
N12
N8
P7
N7
P6
N6
P5
R5
P4
N4
P1
P3
N2
R1
M2
M3
M1

E0
E1
E2

R13

1

AD22
AD20

PCI_CLK

AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
AD16
AD17
AD18
AD19
AD20
AD21
AD22
AD23
AD24
AD25
AD26
AD27
AD28
AD29
AD30
AD31

GPIO_5 1

R

1

R47

B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49

EPRM_SCK
EPRM_SDA
EPRM_EN_L

D1
D2
D3

PCI_MODE
PCI_RST_L
PCI_CLK
PCI_CLKRUN_L

R10

1
2
3

1

0

AD24

IDSEL

RESERVED
GND
CLK
GND
#REQ
+5V(I/O)
AD31
AD29
GND
AD27
AD25
+3V3
#BE3/C
AD23
GND
AD21
AD19
+3V3
AD17
#BE2/C
GND
#IRDY
+3V3
#DEVSEL
GND
#LOCK
#PERR
+3V3
#SERR
+3V3
#BE1/C
AD14
GND
AD12
AD10
GND

H3
H2
J2
J1
H1

R9
R

1

AD28
AD26

RESERV
#RST
+5Vio
#GNT
GND
RESERV
AD30
+3V3
AD28
AD26
GND
AD24
IDSEL
+3V3
AD22
AD20
GND
AD18
AD16
+3V3
#FRAME
GND
#TRDY
GND
#STOP
+3V3
SDONE
#SBO
GND
PAR
AD15
+3V3
AD13
AD11
GND
AD9

K14
L3
K3
R9

R8
390

1

R40

A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49

U0_SOUT
U0_RTS_L
U0_CTS_L
U0_CLK
U0_SIN

U1A
PCI_MODE
PCI_RST_L
PCI_CLK
PCI_CLKRUN_L

0

LED_1

G1
G2
F1
F2
E1
E2

1

AD30

B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11

390

0

NC,0

PCI_PME_L

-12V
TCK
GND
TD0
+5V
+5V
#INTB
#INTD
#PRSNT1
RESERVED
#PRSNT2

0

PCI_GNT_L
C

#TRST
+12V
TMS
TDI
+5V
#INTA
#INTC
+5V
RESERV
+5Vio
RESERV

R12

NC,10K

R43

R5

R4

10K

R6

10K

10K

3.3V_AUX
PCI_RST_L

A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11

C5
C4

R11

J1
PCI-BUS(universal)

TCLK
LED_0
TDI
LED_1
TDO
TMS
GPIO_0
TRST_L GPIO_1
GPIO_2
GPIO_3
GPIO_4
GPIO_5

0

3.3V

3.3V

R7

10K

C1
A3
A2
A1
B1

3.3V

LED_0

U1B

VCC

3.3V_CON 3.3V_CON 3.3V_CON 3.3V_CON

VSS

5V_CON

D

B

AR2414A-00 PCI Interface

CON\PCIB
AR2414A-00 Digital Interface
C71
C60

C70
NC,220uF,EC10V

0.1uF,Y5V

C72
NC,220uF,EC10V

0.1uF,Y5V

3.3V

2

3.3V_CON

5V_CON

2

C73
1000pF

C74

C75
C76
0.01uF 10uF/16V

C31
100uF,EC16V
A

2

R

100uF,EC16V

3.3V

1

C72

A

R53

10K

R52

3

U7
RT9161A-33CG
2 VinVout 3

L17
BLM18HG471

GND

Q

1 GPIO_5

Q

1

1

LED_1 1

Q5
R51
NC

1

LED_1

2

1

3

Q4

3.3V_AUX

NC,10uF/16V

WAKE ON LAN

CAMEO
Product Name

WLG-1202 PCI adapter

5

4

3

2

Size
C

Function Description

Date:

Friday, January 14, 2005

Rev
A2

Connector & Digital
Sheet
1

1

of

4

5

4

3

2

1

D

D

RFOUT_P

3

C8
1.5pF

IDDQ

BIASREF

F13

J15

XTALI

XTALO

J14

1

R16
1

PUT TP15
ON TOP LAYER
TP15
1
VREG_COMP
VREG_OUT

Q2
2SB1132

3

BIASREF

R19

XTALO

1.8V_A

XY1
C7

Y

1

3

10V

AR2414A-00 Radio Interface
0.1uF

390

J13
G13

C11

R20

XTALI

VREG_COMP
VREG_OUT

C

2

0
R

TX2

C2

C6

C4

10pF

R23

XBIAS

C15
C14

R21

2
5
6

3.3V_A
C147

ATBP
ATBN

43K

ADC_DAC_IP
ADC_DAC_IN
ADC_DAC_QP
ADC_DAC_QN

2.2pF

RFOUT_P
RFOUT_N

A10
A7

R17

G15
G14
E14
E15

2.2pF

RFOUTP_BIAS
RFOUTN_BIAS

C3

RFINP
RFINN

10pF

A13
A12

A9
A8

C2

R R45

C146

RFOUTP
RFOUTN

120pF

PDETP
PDETN

4

47

1
1

C9
C8

6.19K
1%

0

3

P_DET

2.2pF

1

R49

BALU N

P_DET
OPT

R18

RFIN

0

R48
3

F6

3
3

3

3.3V_A

L11
3.3nH

U1D
C

3.3V_A

0

1

XBIAS
L12
3.3nH

TP18
1

TP16

1.8V_A

TP19

R22

1.8V_A
TP17

C5
10uF

Y1
40.000MHZ

3

BIASREF

15pF

C10

C9

22pF

1

VREG

B

B

XTAL

A

A

CAMEO
Product Name

WLG-1202 PCI adapter

5

4

3

2

Size
C

Function Description

Date:

Friday, January 14, 2005

Rev
A2

Radio_Interface
Sheet
1

2

of

4

5

4

3

2

1

3.3V_A

C12
1uF

PRINTED TRANSMIT
COMBLINE FILTER

D

D

R25
0R

F3

C24
NC

GND

W10 L30

C23
10pF

4
6
7

0

0

Vhigh

J1-J2

R33
1K

J1-J3

Isolation

IL

IL

ANTB 1

TX Mode

Isolation

ANT1

RX Mode
C30
10pF

U2
F2

W10 L120
11
10

REF
DET
GND

8
9
17

C28
3pF(phycom) C25
NC

L14
NC

V2

Vhigh

PA2409

RF IN RF OUT
RF IN RF OUT
VB1
VB2
VB3

C16
0.1uF

V1

L16
10nH

3

2

1

C145
47pF

C20
10pF

C14
10pF
4

1

2
R27
47

C26
1.5pF

NC
NC
NC

C27
3pF(phycom)

OUT

5

1
13
15

C29
NC

GND

GND

IN

2
3

3

C22
10pF

2

C21
1.5pF

1

2 RFOUT_P

C

PRINTED BPF

4

C19
NC

5
16
14
12

C18
NC

6

OUTPUT MATCHING

C17
NC

VCC
VC1
VC2
VC3

C142
3pF(phycom)

C144
NC

W10 L70

R46
1.5nH

4-PIN-COUPLER
W=20
S=5
L=180

U6

3

J3

V2

6

GND

J1

5

J2

V1

4

F4

2

O

C34
10pF

I

E1

ANT 1

C78
NC
C11
15pF

1

C13
2.2pF

3

E

2

RF

1

4

E

5

SMA
ANT\RP-SMA

L1
3.3nH

NJG1600KB2
IC6\SC70\0.65
R30
R31
R32
180,1%82.5,1%150,1%

E

E

R26
1K

R29
100K

OPT 2

ANTA 1

D1
1
2 XBIAS

XBIAS

L4
3.9nH

R28
100K

C

L5
3.9nH
C33
47pF

2

P_DET 2

SMS7630-996

C32
10pF

C61
10pF
R35
NC

C15
10pF

C

R36
5.1K

1 ANTC

R37
56

C36
220pF

B

B

PRINTED RECEIVE
COMBLINE FILTER
2

R38
15K

C37
10pF

L7
18nH

R39
47

INPUT MATCHING

2

1

C38
3pF(phycom)

6

L8
18nH

C40
10pF

C43
3pF(phycom)

SGA-8343

C

C42
10pF

4

RFIN 2

GND

GND

IN

1

GND

Q3
1

OUT

3

R34
NC

3

1

R24
NC

5
C41
10pF

L15
1nH

F5

PRINTED BPF

50 OHM LINES

2

C39
120pF

C44
3pF(phycom)

C45
NC

L10
NC

4
2

C46
10pF

C47
NC

A

A

CAMEO
Product Name

WLG-1202 PCI adapter

5

4

3

2

Size
C

Function Description

Date:

Friday, January 14, 2005

Rev
A2

Front_End
Sheet
1

3

of

4

5

4

3

2

3.3V

1

1.8V
VR3

0.1uF

10V

C141

R42

0.1uF

10V

C50

10V

C49

1.8V_A

1000pF

1.8V

C51

3.3V_A

1uF

2.2uF

R41

10V

10pF
10pF

C48

10pF

C59

C58
C68

C69

1000pF
1000pF

10pF

C57
C67

1000pF

C56

25V

25V

0.01uF

C55

0.01uF

C54

0.1uF

10V

C53

0.1uF

10V

3.3V

0

C52

3.3V_A

1000pF

C66

25V

0.01uF

C65

25V

0.01uF

C64

0.1uF

10V

10V

C63

1.8V_A

0.1uF

1.8V

C62

D

0

3.3V

3

1

C1
NC

OUT

C

IN

C140

2

D

GND

VR

C

C

U1H

3.3V

U1F
1.8V

B2
C3
D4
D6
E5
E6
E7
E8
F4
F5
F6
F7
F8
G5
G6
G7
G8
H5
H6
H7
J5
J6
J7
J8
J9

U1E

TOOLING
HOLES
X33 1
X39

B

X99

X14
X28

GND
GND
GND
GND
GND
GND

X31

1

X32

1

1

X572

1

X524

X336

1

X502

X29

1

X30

1

X10

1

X9

1

X11

1

X8

1

1

X597

1

1

X548

1

X518

1

X602

1

1

X545

1

X594

1

X562

1

X563

1

X527

1

X538

1

X578

1

X600

1

1

X601

1

X598

1

X526

1

X568

1

X564

1

X536

1

X575

1

X546

1

X557

1

X573

1

X555

1

1

X588

1

X558

X577

1

1

X561

X603

1

X342

1

X547

1

1
1

X596

1
1

X582

X535

1

X339

1

1

X571

1

X586

X595

1

X589

1

X333

1

X585

1

1

X583

1

X593

X517

1

X332

1

X599

1

X519

1

X329
X591

1

X590

1

X569

1

X327

1

X503

1

X570

1

1

X338

1

X579

1

X335

1

X565

1

X556

1

X605

1

X504

1

X581

1

X574

1

X576

1

X525

1

X607

1

X537

1

X516

1

X584

1

X606

1

X587

1

X505

1

X580

1

X604

1

X330

1

X592

1

X341

1

FD1

1 FD500

1

FD2

1 FD501

1

FD3

1 FD502

1

FD4

1

TOOLING HOLES

VDD18
VDD18
VDD18
VDD18
VDD18
VDD18
VDD18
VDD18

D5
D8
E4
H4
L4
L12
M5
M8
M11
N5
N11

VDD33
VDD33
VDD33
VDD33
VDD33
VDD33
VDD33
VDD33
VDD33
VDD33
VDD33

GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

A11
A14
A15
B7
B10
B11
B12
B13
B14
C13
D10
D12
D14
E9
E10
E11
F9
F10
F11
F12
F14
G9
G10
G11
H9
H10
H11
H13

3.3V_A

J10
J11
K4
K5
K6
K7
K8
K9
K10
K11
K12
L5
L6
L7
L8
L9
L10
L11
M4
M6
M10
M12
N3
N13
P2

1.8V_A
U1G

AR2414A-00 Digital VDD

B8
B9
B15
C7
D9
D13
F15
G12
H14

AVDD
AVDD
AVDD
AVDD
AVDD
AVDD
AVDD
AVDD
AVDD

C10
C12
D11
D15
E12
E13
H12
H15

AVDD33
AVDD33
AVDD33
AVDD33
AVDD33
AVDD33
AVDD33
AVDD33

AR2414A-00 Analog VDD

AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND

B

AR2414A-00 Digital Ground
AR2414A-00 Analog Ground

BREAKAWAYS

X441
PCB_CB
1

A

1

X22

X560

FIDUCIALS

OPTIONAL SHIELD
HOLES

X21

X326

CB51 SHIELD

1
2
3
4
5
6

1

PANEL PERFORATIONS

D7
G3
G4
J3
J4
J12
M7
M9

GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

LOGO

X7

1

X12

X614

1

1

X615

1

X13

1

X616

1

X608

1

X617

1

X609

1

X618

1

ZH1

1

X610

1

X619

1

X1

1

ZH500

1

X611

1

X620

1

X2

1

ZH501

1

X612

1

X621

1

ZH502

1

X613

1

X622

1

ZH503

1

Tie ground
planes
together.

A

CAMEO
Product Name

WLG-1202 PCI adapter

5

4

3

2

Size
C

Function Description

Date:

Friday, January 14, 2005

Rev
A2

Power&Misc
Sheet
1

4

of

4

PCB Layout

Bill of Materials (Part List)

WLG-1202 PCI adapter Bill of material
Item Quantity Reference
Capacitance
1
3 C8,C21,C26
2
4 C7,C13,C146,C147
3
6 C27,C28,C38,C43,C44,C142
C3,C4,C14,C15,C20,C22,C23
C30,C32,C34,C37,C40,C41,
C42,C46,C58,C59,C61,C68,
4
20 C69
5
2 C10,C11
6
1 C9
7
2 C33,C145
8
2 C2,C39
9
1 C36
10
6 C51,C56,C57,C66,C67,C73
11
5 C54,C55,C64,C65,C75
C6,C16,C50,C52,C53,C60,C62,C63,
12
10 C71,C141
13
2 C12,C49
14
2 C48
15
2 C5,C76
16
1 L15
17
1 R46
18
3 L1,L11,L12
19
2 L4,L5
20
1 L16
21
2 L7,L8
22
1 L17
R1,R2,R3,R13,R18,R25,R47,R48,
23
9 R49
24
3 R19,R41,R42
25
1 R16
26
3 R22,R27,R39
27
1 R37
28
1 R31
29
1 R32
30
1 R30
31
3 R7,R8,R20
32
2 R26,R33
33
1 R36
34
1 R21
R4,R5,R6,R11,R12,R14
35
7 R52
36
1 R38
37
1 R17
38
2 R28,R29
39
1 D1
40
1 Q2

Part

PCB Footprint

1.5pF
2.2pF

CAP-0402
CAP-0402
3pF+/-0.1P(phycom) CAP-0402

10pF
15pF
22pF
47pF
120pF
220pF
1000pF
0.01uF

CAP-0402
CAP-0402
CAP-0402
CAP-0402
CAP-0402
CAP-0402
CAP-0402
CAP-0402

0.1uF
1uF
2.2uF
10uF
1nH
1.5nH
3.3nH
3.9nH
10nH
18nH
BEAD, 60O,500mA

CAP-0402
CAP-0603
CAP-0805
CAP-0805
IND-0402
IND-0402
IND-0402
IND-0402
IND-0402
IND-0402
RES-0603

0
0
1
47
56
82.5,1%
150,1%
180,1%
390
1K
5.1K
6.19K,1%

RES-0402
RES-0805
RES-0603
RES-0402
RES-0402
RES-0402
RES-0402
RES-0402
RES-0402
RES-0402
RES-0402
RES-0402

10K
15K
43K
100K
SMS7630-996
2SB1132

RES-0402
RES-0402
RES-0402
RES-0402
DIO-SC-70
SOT89-MIRRORED

41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56

1 Q3
1 U1
1 U2
1 U3
1 U6
1 Y1
1 U7
1 PCB 4層, Netgaear, WG311Tv1h3主板, REV.A1
1 Shielding Box-Frame, 無色
2 螺絲 圓頭 +字 無頸下物 公制牙(粗牙) 鍍鎳
1 BRACKET, PCI, 上折邊, 鍍鎳, 打字,SMA頭
1 E1
1 LED1
2 C31,C72
1 Shielding Box-Cover, 無色
1 分離式天線,2dbi

LNA-2.4GHZ-SGA-8343

SOT-343

AR2414A-00 Digital VDD BGA-224-15X15

NJG1600KB2
SO8
Epicom
FY4000041
RT9161A-33CG

SMA
LED-GREEN-(2)
EC-100uF

IC6\SC70\0.65
M24C32WMN6

PA-2409
CRY-SMD4-40MHz

SOT-223

ANT\RP-SMA
Holder 90° 3? 5mm

Exterior and Interior Photographs

External Photos of 802.11g Wireless PCI Adapter ---------------------------------- 1/4

Applicant: CAMEO COMMUNICATIONS, INC. FCC ID: NHPWLG1202
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

External Photos of 802.11g Wireless PCI Adapter ---------------------------------- 2/4

Applicant: CAMEO COMMUNICATIONS, INC. FCC ID: NHPWLG1202
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

External Photos of 802.11g Wireless PCI Adapter ---------------------------------- 3/4

Applicant: CAMEO COMMUNICATIONS, INC. FCC ID: NHPWLG1202
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

External Photos of 802.11g Wireless PCI Adapter ---------------------------------- 4/4

Applicant: CAMEO COMMUNICATIONS, INC. FCC ID: NHPWLG1202
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Label Information

94.04.12 WLG-1202/X

9500WLG12020XAV

Joseph Liu Grace Chen

CAMEO

51.00 mm

MODEL : WLG-1202/X
Q'TY:

WLG-1202/X Rev.AV
25.00 mm

802.11g WLAN
PCI Adapter

40 PCS

0470

FCC ID: NHPWLG1202
"See Caution in Manual"

S/N:

Made in XXXXXX

FROM
¾ ÷ Å é ¶ K ¯ È

S/N:

40.00 mm

WLG-1202/X

FCC ID: NHPWLG1202
"See Caution in Manual"

S/N:

34.00 mm

0470
CARTON OF NO.

6.00 mm

MAC: 000000000000

/

MADE IN xxxxxx

0470

Technical Description

TECHNICAL SPECIFICATIONS
General
Radio Technology

IEEE 802.11b Direct Sequence Spread Spectrum (DSSS)
IEEE 802.11g Orthogonal Frequency Division Multiplexing
(OFDM)

Interface

32-bit PCI 2.1, 2.2. Bus Master

Data Transfer Rate

1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54Mbps (auto sense)

Receiver Sensitivity

54Mbps: Typical -73dBm @ 10% PER (Packet Error Rate)
11Mbps: Typical -85dBm @ 8% PER (Packet Error Rate)
802.11g: 14dBm typically
802.11b: 18dBm typically

Transmit Rate
Frequency Range

2412 ~ 2484 MHz ISM band (channels 1 ~ 14)

Modulation Schemes

DBPSK/DQPSK/CCK/OFDM

Channels

1~11 channels (FCC), 1~13 channels (ETSI), 1~14 channels
(MKK-Japan)

Media Access Protocol

CSMA/CA with ACK

Security

64/128-bits WEP Encryption, WPA

Diagnostic LED

LNK (Link status), ACT (Activity status)

Antenna

1.8 dBi Dipole Antenna

Physical and Environmental
Driver Support
Continuous
Consumption

Windows 98se, Windows 2000, Windows ME, Windows XP
Current

250mA typ. for receive mode, 350mA typ. for transmit mode

Temperature

Operating: 0° ~ 40° C, Storage: -10° ~ 70° C

Humidity

10% ~ 95% RH, no condensation

Dimensions

133 x 121 x 21.6 mm (without antenna)

Certifications

FCC Part 15.247 for US, ETS 300 328 for Europe,

User Manual

IEEE 802.11g
PCI Adapter

User’s Guide

Regulatory notes and statements
Wireless LAN, Health and Authorization for use
Radio frequency electromagnetic energy is emitted from Wireless LAN devices.
The energy levels of these emissions however are far much less than the
electromagnetic energy emissions from wireless devices like for example mobile
phones. Wireless LAN devices are safe for use frequency safety standards and
recommendations. The use of Wireless LAN devices may be restricted in some
situations or environments for example:
·On board of airplanes, or
·In an explosive environment, or
·In case the interference risk to other devices or services is perceived or identified
as harmful
In case the policy regarding the use of Wireless LAN devices in specific
organizations or environments (e.g. airports, hospitals, chemical/oil/gas industrial
plants, private buildings etc.) is not clear, please ask for authorization to use these
devices prior to operating the equipment.

Regulatory Information/disclaimers
Installation and use of this Wireless LAN device must be in strict accordance with
the instructions included in the user documentation provided with the product. Any
changes or modifications made to this device that are not expressly approved by the
manufacturer may void the user’s authority to operate the equipment. The
Manufacturer is not responsible for any radio or television interference caused by
unauthorized modification of this device, of the substitution or attachment.
Manufacturer and its authorized resellers or distributors will assume no liability for
any damage or violation of government regulations arising from failing to comply
with these guidelines.

USA-FCC (Federal Communications Commission) statement
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause
undesired operation of this device.

FCC Radio Frequency Exposure statement
This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65
and found compliant to the requirements as set forth in CFR 47 Sections 2.1091,
2.1093, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices.
i

The radiated output power of this Wireless LAN device is far below the FCC radio
frequency exposure limits. Nevertheless, this device shall be used in such a manner
that the potential for human contact during normal operation is minimized.
When nearby persons has to be kept to ensure RF exposure compliance, in order to
comply with RF exposure limits established in the ANSI C95.1 standards, the
distance between the antennas and the user should not be less than 20 cm.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instructions, it may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Export restrictions
This product or software contains encryption code that may not be exported or
transferred from the US of Canada without an approved US Department of
Commerce export license.
Safety Information
Your device contains a low power transmitter. When device is transmitted it sends
out radio frequency (RF) signal.
CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this
equipment should be installed and operated with minimum distance 20cm between
the radiator and your body. Use on the supplied antenna. Unauthorized antenna,
modification, or attachments could damage the transmitter and may violate FCC
regulations.

ii

The antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating
in conjunction with any other antenna or transmitter.

CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950 has been conducted. These are
considered relevant and sufficient.

Protection requirements for electromagnetic compatibility – Article
3.1b
Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 48917 and EN 55024 has been conducted. These are considered relevant and sufficient.

Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328-2 has been conducted. These
are considered relevant and sufficient.

CE in which Countries where the product may be used freely:
Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland,
Denmark, Luxembourg, Austria, Finland, Sweden, Norway and Iceland.
France: except the channel 10 through 13, law prohibits the use of other channels.

iii

TABLE OF CONTENT
Introduction .................................................................................................1
Overview of this User’s Guide ..................................................................1
Unpacking and Setup...................................................................................2
Unpacking..................................................................................................2
Setup ..........................................................................................................2
Hardware Installation ..................................................................................3
LED Indicator............................................................................................3
Check the installation ................................................................................3
Software Installation....................................................................................4
Windows 98se/ME/2000/XP Utility and Driver Installation ....................4
Wireless Utility Setting .............................................................................5

iv

INTRODUCTION
Congratulations on your purchase of this IEEE 802.11g Wireless PCI Adapter.
This manual helps to get familiar with the Wireless PCI Adapter. This manual
contains detailed instructions in operation of this product. Please keep this manual
for future reference.
With a Wireless (IEEE 802.11g) PCI Adapter, a computer or a station can
communicate with another computer in a wireless way. Easy-to-use utilities are
bundled with Wireless PCI Adapter for configuration, monitoring, and diagnosis
purposes.
Wireless PCI Adapter can wirelessly transmit and receive data, minimizing the
need for wired connections, at a speed of up to fifty-four megabit per second. With
Wireless PCI Adapter, you can locate your PC or station wherever you want
without wires and cables.
Wireless PCI Adapter provides users with an access to real-time information
anywhere in their organization. The mobility provides productivity and service,
which are not available under wired networks. The Wireless PCI Adapter
configuration is easy to change from peer-to-peer networks, suitable for a small
number of users, to full infrastructure networks of thousands of users that allow
roaming around a broad area.

Overview of this User’s Guide
Introduction. Describes the Wireless PCI Adapter.
Unpacking and Setup. Helps you get started with the basic installation of the
Wireless PCI Adapter.
Hardware Installation. Describes the LED indicators of the Adapter.
Software Installation. Tells how to setup the driver and the utility setting.
Technical Specifications. Lists the technical (general, physical and environmental)
specifications of the Wireless PCI Adapter.

1

UNPACKING AND SETUP
This chapter provides unpacking and setup information for the Wireless PCI
Adapter.

Unpacking
Open the box of the Wireless PCI Adapter and carefully unpack it. The box should
contain the following items:
u
u

One 802.11g Wireless PCI Adapter
One Driver & Utility CD-ROM

If any item is found missing or damaged, please contact your local reseller for
replacement.

Setup
The setup of the Wireless PCI Adapter can be performed using the following steps:
u
Visually inspect the PCI Adapter and make sure that it is fully plugged in to the
PC’s PCI slot.
u
Make sure that there is a well environment that there is no much intrusion to
have a better connection.

2

HARDWARE INSTALLATION
LED Indicator
LNK (Link)
The LNK indicator indicates green when the Wireless PCI Adapter is connected to
a network successfully.
ACT (Activity)
The ACT indicator blinks green continuously whiles the Wireless PCI Adapter is
transmitting data.

Check the installation
1. Shut down the computer, unplugs its power cord, and remove the chassis cover.
2. Insert the contact edge of the Wireless PCI Adapter into the connector of any
available PCI Bus Master Expansion slot. Press the card firmly into the connector
such that the card’s contacts are fully seated in the PCI slot connector.
3. Install the bracket screw and secure the card to the computer chassis.
4. Cover the computer’s chassis.
5. Switch computer power on. The computer will automatically activate the newly
installed driver and utility the Wireless PCI Adapter.

3

SOFTWARE INSTALLATION
This section will lead you to install the driver and utility of the Wireless Cardbus
Adapter.

Windows 98se/ME/2000/XP Utility and Driver Installation
1. Insert the Wireless Cardbus Adapter Driver & Utility CD-ROM into computer’s
CD-ROM Drive and it will automatically run a setup menu and install the driver
and the utility. In some specific setting on Windows system, you may need to
proceed the software manually, go to your Windows Start menu and choose
Run, type “D:\Utility\Setup.exe” in the dialog box (D:\ will depend on where
your CD-ROM drive is located) and click OK.
2. If you need to install the driver manually, refer each Windows OS to the
following CD-Rom directory path: D:\Driver\\net5211.inf.
Note: (D:\ will depends on where the CD-ROM drive is located and
 will depend on the Windows OS you are using).

3. The Install Shield Wizard screen will appear. Click “Next” to continue.
4. The installation program will help you to setup the Wireless Cardbus utility.
Be noted that the Windows XP have its own Wireless Utility; you can either
use the utility of Windows XP or the provided utility.
5. When the Wireless Cardbus Adapter was installed, you will see the icon on the
Windows task bar.

When the icon in the toolbar represents in full green color then the signal
strength has an excellent performance with the AP, if it represents in yellow
color then the signal strength has a fair performance with the AP, and if the icon
represents no color, then the signal strength has a worst performance with the
wireless station.
4

Wireless Utility Setting
I. Link Information
The default page is as below after launching the Utility program.

Status: Shows the BSSID associated, which can be used to identify the wireless
network.
SSID: Shows current SSID, which must be the same for the wireless client and AP
in order for communication to be established.
Frequency: Shows the current frequency used for wireless network.
Wireless Mode: Shows the current wireless mode used for wireless communication.
Encryption: Shows the current encryption mode used for wireless network.
TxRate: Shows the current data rate used for transmitting.
Channel: Shows the current channel for commu nication.
Link Quality: Shows the link quality of the 108Mbps wireless LAN PC card with
the Access Point when operating under Infrastructure mode.
Signal Strength: Shows the wireless signal strength of the connection between the
108Mbps wireless LAN PC card with the Access Point.
Data Rate: Shows the statistics of data transfer, and the calculation is based on the
number of packets transmitted and received.

5

II. Configuration
This is the page where changes the basic settings of the PC card with the minimum
amount of effort to implement a secure wireless network environment.

SSID: Service Set Identifier, which is a unique name shared among all clients and
nodes in a wireless network. The SSID must be identical for each clients and nodes
in the wireless network.
Wireless Mode: There are two types available for selection
?Infrastructure – to establish wireless communication with LAN and other wireless
clients through the use the Access Points.
?Ad-Hoc – to establish point-to-point wireless communication directly with other
wireless client devices such as wireless network PCI Adapter.
AdHoc Band: There are two bands available for selection- 11B and 11G
Channel: The value of channel that AP will operate in. User can select the channel
range of 1 to 11 for North America (FCC) domain and 1 to 13 for European (ETSI)
domain and 1 to 14 for Japanese domain.
Tx Rate: Select the data rate for data transmission.
Power Mode: There are 3 modes to choose.
?Continuous Access Mode (default) – the PC card is constantly operating with full
power and it consumes the most power.
? Maximum Power Save – the PC card consumes the least power and only operates
when there is wireless network activity.
?Power Save – the PC card consumes the moderate level of power.

6

Preamble: Select Long or Short Preamble type. Preamble is a sequence of bits
transmitted at 1Mbps that allows the PHY circuitry to reach steady-state
demodulation and synchronization of bit clock and frame start. Two different
preambles and headers are defined: the mandatory supported Long Preamble and
header, which interoperate with the 1 Mbit/s and 2 Mbit/s DSSS specification (as
described in IEEE Std 802.11), and an optional Short Preamble and header (as
described in IEEE Std 802.11b). At the receiver, the Preamble and header are
processed to aid in demodulation and delivery of the PSDU. The Short Preamble
and header may be used to minimize overhead and, thus, maximize the network
data throughput. However, the Short Preamble is supported only from the IEEE
802.11b (High- Rate) standard and not from the original IEEE 802.11. That means
that stations using Short-Preamble cannot communicate with stations implementing
the original version of the protocol. Click “Apply” for the changes to take effect.
Support Band: There are three functions for users select, including 11B, 11G and
eXtended Range. The default setting is 11B, 11G and eXtended Range enable,
which is interoperable with both 11B and 11G devices, and provide more than
500m connection ability.
Note: user must select one of 11B or 11G at least, otherwise the wireless
connection will not function.
III. Advanced
This is the page to configure Security settings of 108Mbps wireless LAN PC card.

Encryption: 4 options are available: Disable, Enable, WPA and WPA-PSK.
Select Enable or Disable for WEP data encryption feature. If one of the two
7

options is selected, it is required to select the Authentication mode from the next
dropping list. If WPA is selected, configuration is enabled. Please click the
“configuration”. The below window is pop up. Then, please select the certificate
that user wants to use and enter the server name and login name

If WPA-PSK is selected, click the configuration button. The popping window is as
the below. Please enter the key.

Auth. Mode: There are three modes available to choose.
?Open Authentication – the sender and receiver do not share secret Key for
communication. Instead, each party generates its own key-pairs and asks the other
party to accept it. The key is regenerated when the connection is established every
time.
?Shared Authentication – the sender and receiver shares the common key for
data communication, and the key is used for extended length of time.
?Auto – depend on the communication to establish, and automatically use the
proper authentication mode.
The following will only be activated to allow for configuration when Encryption is
enabled.
Default Key: select one of the 4 keys to use.
8

Network Key: choose the encryption way, either in HEX or ASCII formats, and
enter the password in the blank space.
Key Length: select 64 or 128 bits as the length of the keys
Key Format: ASCII or HEX
IV. Site Survey
This page allows user to enable the Site Survey function to scan for the available
wireless network (wireless clients and Access Points) and establish wireless
communications with one.

Available Network – displays the wireless networks (wireless clients and Access
Points) that are in signal range.
Select any one of them to establish communications by simply mouse double-click
or click on the “Connect” button.
Click “Refresh” button to start scanning for available network again.
Profile – User can create and manage the created profiles for Home, offices or
public areas. By double-clicking on one of the created profile, the setting will adapt
to the configuration such as SSID, channel, and WEP settings saved by that
particular profile.
Remove: To remove the selected the profile
Properties: To view and change its settings of the profile.

9

Add: To add a profile. Then, the following screen would appear. User can enter the
necessary information required for accessing Access Points or Wireless Router.

V. About
This page displays some information about the 108Mpbs wireless LAN PC card
utility, which includes the version numbers for Driver, Firmware and Utility. When
there is new version of software available for upgrade, users will be able to identify
by version numbers.

10

R&TTE Standards List

R&TTE List of Standard
With referring to the article of the directive of R&TTE 1999/5/EC, the following equipment:
Product Description / Supplementary Info
Manufacturer
Brand
Type

802.11g Wireless PCI Adapter
CAMEO COMMUNICATIONS, INC.
CAMEO, Level One, LG, Etherwan, Allnet GmbH
WLG-1202, WNC-0300, LWS5410P, NWP-0108G, ALL0281A

has been tested to and conforms with the following List of R&TTE Harmonized standards:
Standard
ETSI EN 300 328-2
ETSI RF Specification

Issue date
V1.2.1 Dec. 2001
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
Transmission systems; Data transmission equipment operating in the 2,4GHz
ISM band and using spread spectrum modulation techniques; Harmonized
EN covering essential requirements under article 3.2 of the R&TTE Directive.

Meets R&TTE directive art. 3.2.a on effective use of radio frequency
spectrum so as to avoid harmful interference.
ETSI EN 301 489-1
V1.4.1 Aug. 2002
ETSI EN 301 489-17
V1.2.1 Apr. 2002
ETSI EMC Specification Electromagnetic compatibility and Radio spectrum Matters(ERM);
Electro Magnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common Technical requirements; Part 17: Specific
conditions for Wideband data and HIPERLAN equipment.
Meets R&TTE directive art. 3.1.b of essential requirements on protection with
respect to Electro Magnetic Compatibility.
As such standards referred to tin Article 5 of the directive have not been applied or do not exist, the
following Adopted solutions with descriptions and explanations as listed below, have been applied
in full or in part, to meet the essential requirements of the directive:
Standard
EN 60950-1
LVD specification

Issue date
2001
Safety of information technology equipment, including electrical business
equipment.
Meets R&TTE directive art. 3.1.a of essential requirements on protection of
the health and safety of the user.

Draw up in
Date

TAIWAN, R.O.C.
2005/4/27
CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6,
Taipei 114, Taiwan

Signature & company stamp

Jason Chang /
Wireless Comm. R&D Dept. Manager

RF & EMC Test Reports and
Corresponding Annexes

Test Report -------------------------------------------------------------------------------- 1/38
Report No.

C51ET050304

Specifications

ETSI EN 300 328-1 (V.1.3.1) / December, 2001
ETSI EN 300 328-2 (V.1.2.1) / December, 2001

Applicant

CAMEO COMMUNICATIONS, INC.

Applicant
address

No. 42, Min Chuan East Road, Section 6,
Taipei 114, Taiwan

Items tested
Model No.

802.11g Wireless PCI Adapter
W LG-1202, WNC- 0300, LWS5410P, NWP-0108G,
ALL0281A

EUT Condition

Engineering sample;
(Sample # N10415)

Results
Date

Compliance (As detailed within this report)
12/01/2004 (month / day / year) (Sample received)
12/14/2004 (month / day / year) (Test)

Pre-production;

Prepared by
______________________
Authorized by
Issue date

December 16, 2004

Final production

Project Engineer
(Jack Tsai)
General Manager
(Frank Tsai)
(month / day / year)

Modifications
Tested by

None
Training Research Co., Ltd.

Office at

No. 255, Nan Yang Street, Shijr City, Taipei Hsien 221, Taiwan

Laboratory at

1F, No. 255, Nan Yang Street, Shijr City, Taipei Hsien 221, Taiwan

Open site at

No. 15, Lane 530, Balian Rd., Sec. 1, Shijr City, Taipei Hsien 221, Taiwan

Conditions of issue:
This test report shall not be reproduced except in full, without written approval of
TRC. And the test result contained within this report only relate to the sample submitted
for testing.

Ϫ Aut. No. ELA 131

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 2/38

We here by verify that:
The test data, data evaluation, test procedures and equipment configurations shown in this report
were made mainly in accordance with the procedures given in ETSI EN 300328-2 (V.1.2.1) as a
reference. All test were conducted by Training Research Co., Ltd., 255 Nanyang Street, Shijr, Taipei
Hsien 221, Taiwan, R.O.C. Also, we attest to the accuracy of each.
We further submit that the energy emitted by the sample EUT tested as described in the report is
in compliance with the technical requirements set second edition in the European Telecommunication
Standard ETSI EN 300328-2 (V.1.2.1).

Reservation:
The test results herein refer only to the tested sample. Training Research Co., Ltd. is not
responsible for any generalizations or conclusions draw from these test results and concerning further
samples. Any modification of the tested samples is prohibited and leads to the invalidity of this test report.

Test by :

Training Research Co., Ltd.
TEL: 886-2-26935155

FAX: 886-2-26934440

No. 255, Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C.

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 3/38

Tables of Contents
I.

GENERAL ..........................................................................................4
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9

II.

SECTION 5.2.1: EFFECTIVE RADIATED POWER....................11
2.1
2.2
2.3

III.

Test Result of Frequency Range for IEEE 802.11b.................................................18
Test Result of Frequency Range for IEEE 802.11g.................................................20
Test Result of Frequency Range for Super 802.11g ................................................22

SECTION 5.2.4: TRANSMITTER SPURIOUS EMISSIONS .......24
5.1
5.2
5.3

VI.

Test Result of Peak Power Density for IEEE 802.11b.............................................14
Test Result of Peak Power Density for IEEE 802.11g.............................................14
Test Result of Peak Power Density for Super 802.11g............................................14

SECTION 5.2.3 : FREQUENCY RANGE.......................................18
4.1
4.2
4.3

V.

Test Result of Effective Radiated Power for IEEE 802.11b.....................................11
Test Result of Effective Radiated Power for IEEE 802.11g.....................................12
Test Result of Effective Radiated Power for Super 802.11g....................................13

SECTION 5.2.2: PEAK POWER DENSITY...................................14
3.1
3.2
3.3

IV.

INTRODUCTION ........................................................................................................4
DESCRIPTION OF EUT ..............................................................................................4
TEST METHOD .........................................................................................................4
DESCRIPTION OF SUPPORT EQUIPMENT ....................................................................5
CONFIGURATION OF SYSTEM UNDER TEST ...............................................................7
VERIFY THE FREQUENCY AND CHANNEL ..................................................................8
TEST PROCEDURE.....................................................................................................8
LOCATION OF THE TEST SITE ...................................................................................8
GENERAL TEST CONDITION......................................................................................9

Test Result for IEEE 802.11b.................................................................................24
Test Result for IEEE 802.11g.................................................................................27
Test Result for Super 802.11g................................................................................29

SECTION 5.3.2: RECEIVER SPURIOUS EMISSIONS................30
6.1
6.2
6.3
6.4

Test Result for IEEE 802.11b.................................................................................30
Test Result for IEEE 802.11g.................................................................................33
Test Result for Super 802.11g................................................................................35
Test Result for Standby mode.................................................................................36

VII. INSTRUMENT AND ANCILLARIES EQUIPMENT OF LIST ....37
Appendix A: Antenna Specification............................................................38

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 4/38

I. GENERAL
1.1. Introduction
The following measurement report is submitted on behalf of Applicant in support of a wireless
LAN measurement in accordance with ETSI EN 300328-2 (V.1.2.1) (Dec. 2001) of the European
Telecommunication Standard.

1.2. Description of EUT
Product Name

:

802.11g Wireless PCI Adapter

Model No.

:

WLG-1202, WNC-0300, LWS5410P,
NWP-0108G, ALL0281A

Frequency Range

:

2.400GHz ~ 2.4835GHz

Operating Frequency

:

2.412GHz ~ 2.472GHz

Support Channel

:

13 Channels

Modulation Skill

:

DBPSK, DQPSK, CCK, OFDM

Power Type

:

Power by PCI of client’ s device

Power Cable

:

None

Data Cable

:

None

1.3. Test Method
1. Put the EUT into a personal computer’ s PCI bus and fix it.
2. Using the notebook computer and software provided by the manufacturer to control the
EUT. The test is performed under those specific conditions.
3. Set different channel [ CH1/CH7/CH13/Super 802.11g (only CH7) ] and data rate being
tested, and then making EUT to the following modes:
a) The mode of continuous transmission.
b) The receive mode.
c) The standby mode.

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 5/38

1.4. Description of Support Equipment
In order to construct the minimum testing, following equipment were used as the support units.

PC

:

IBM 6840

Model No.

:

6840MJV

Serial No.

:

96CC 0BT

FCC ID

:

DoC Approved

ᛀ጖

:

3892I279

Power type

:

100 ~ 127/ 200 ~ 240VAC, 4A/2A 50/60 Hz, Switching

Power cord

:

Non-shielded, 182cm length, Plastic hood, No ferrite core

Monitor

:

HP 15’ Color Monitor

Model No.

:

D2827A

Serial No.

:

KR91161716

FCC ID

:

C5F7NFCMC1518X

ᛀ጖

:

3872B039

Power type

:

110 ~ 240 VAC / 50 ~ 60 Hz, Switching

Power cord

:

Shielded, 1.83m long, No ferrite core

Data cable

:

Shielded, 1.46m long, with two ferrite cores

PS/2 Keyboard

:

HP

Model No.

:

5181

Serial No.

:

BE21700405

FCC ID

:

DoC Approved

ᛀ጖

:

3892C981

Power type

:

By PC

Data cable

:

Shielded, 1.70m length, with ferrite core

PS/2 Mouse

:

HP

Model No.

:

M-S34

Serial No.

:

LZB90714106

FCC ID

:

DZL211029

ᛀ጖

:

4862A011

Power type

:

By PC

Power cord

:

Non-shielded, 1.88m long, No ferrite core

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 6/38

Notebook

:

IBM Think Pad X20

Model No.

:

2662-11T

Serial No.

:

FX-1192200/09

FCC ID

:

N/A, DoC Approved

ᛀ጖

:

3892B565

Adaptor

:

IBM

Model No.

:

PA2450U

Serial No.

:

02K6654

FCC ID

:

N/A, DoC Approved

Power type

:

I/P: 100 ~ 240vac, 50 ~ 60 Hz, 0.5A ~ 1.2A; O/P: 16Vdc, 4.5A

Power cord

:

Non-shielded, 1.80m length, Plastic, with ferrite core

WLAN Card
Model No.
FCC ID

:
:
:

Gemtek Technology Co., Ltd.
C911003
MXF-C911003

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 7/38

1.5. Configuration of System Under Test

Power
Source

EUT

Monitor

PC

Test-table
PS/2
Keyboard

PS/2
Mouse

The tests below are carried with the EUT transmitter set at high power in TDD mode. The
EUT is forced to select of output power level and channel number by PC.

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 8/38

1.6. Verify the Frequency and Channel
CH

1

2

3

4

5

6

7

8

9

10

0

2412

2417

2422

2427

2432

2437

2442

2447

2452

2457

1

2462

2467

2472

---

---

---

---

---

---

---

Note:
(1) This is for sure that all frequencies are in 2.4GHz – 2.4835 GHz.
(2) After test, the EUT operating frequencies are in 2.412GHz to 2.472GHz. So all the item as
followed in testing report are need to test these three frequencies:
channel 1, channel 7, and channel 13.
(3) E.T.S.I (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

1.7. Test Procedure
All measurements performed in this report were performed mainly according to the techniques
described in ETSI EN 300328-2 (Dec., 2001) and the pre-setup was written on 1.4 test method, the
detail setup was written on each test item.

1.8. Location of the Test Site
The radiated emissions measurements required by the rules were performed on the
three-meter, Anechoic Chamber (Registration Number: 93906) maintained by Training
Research Co., Ltd. 1F., No. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. Complete
description and measurement data have been placed on file with the commission. The conducted
power line emissions tests and other test items were performed in a anechoic chamber also located at
Training Research Co., Ltd.
No. 255 Nanyang Street, Shijr, Taipei Hsien 221, Taiwan, R.O.C. Training Research Co.,
Ltd. is listed by the FCC as a facility available to do measurement work for others on a contract
basis.

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 9/38

1.9. General Test Condition
The test condition shall be as follows: (See Clause 6)
The NORMAL temperature and humidity conditions for tests shall be any convenient
combination of temperature and humidity within the following ranges:
-temperature: +15к to +35к;
-relative humidity: 20% to 75%.
The normal test voltage for equipment to be connected to the main shall be the nominal mains
voltage.
For purpose of this ETS, the normal voltage shall be the declared voltage or any of the declared
voltages for which the equipment was designed.
The frequency of the test power source corresponding to the AC mains shall be between 49Hz
and 51Hz. When radio equipment is intended for operation from the usual, alternator fed lead-acid
battery power source used on vehicles, then the normal test voltage shall be 1.1 times the nominal
voltage of the battery (6V, 12V, etc.)
For operation from other power sources or types of battery (primary or secondary), the
nominal test voltage shall be as declared by the equipment manufacturer. This shall be recorded in the
test report.
For tests at EXTREME temperatures, measurements shall be made in accordance with the
procedures specified in subclause 6.4.3, at the upper and lower temperatures of the range as follows:
temperature: -20к to +55к;
Where the manufacturer’ s declared operating range does not include the range of -20к to
+55к, the equipment shall be tested over the following temperature ranges:
a)0к to +35кfor equipment intended for INDOOR use only, or intended for use in areas
where the temperature is controlled within this range;
b)Over the extremes of the operating temperature range(s) of the declared host equipment(s)
in case of plug-in radio devices.

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 10/38

The frequency range as in subclause 5.2.3 and the e.i.r.p. Limit in subclause5.2.1 shall not be
exceeded.
Tests at extreme power source voltages specified below are not required when the equipment
under test is designed for operation as part of and powered by another system or piece of equipment.
Where this is the case, the limit values of the host system or host equipment shall apply. The
appropriate limit values shall be declared by the manufacturer and recorded in the test report.
The EXTREME TEST VOLTAGE for equipment to be connected to an AC mains source
shall be the nominal mains voltage ±10%.
When radio equipment is intended for operation from the usual type of alternator fed lead-acid
battery power source used on vehicles, then extreme test voltage shall be 1.3 and 0.9 times the
nominal voltage of the battery (6V, 12V, …etc.).
The lower extreme test voltage for equipment with power source using the following type of
battery, shall be:
-for the Leclanche’ or lithium type battery: 0.85 times the nominal voltage of the battery;
-for the mercury or nickel-cadmium type of battery: 0.9 times the nominal voltage of the
battery.
In both cases, the upper extreme test voltage shall be 1.15 times the nominal voltage of the
battery.
For equipment using other power sources, or capable of being operated from a variety of
power sources (primary or secondary), the extreme test voltages shall be those declared by the
manufacturer; these shall be recorded in the test report. Before measurements are made the
equipment shall have reached thermal balance in the test chamber.

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 11/38

II. Section 5.2.1: Effective Radiated Power
2.1

Test Result of Effective Radiated Power for IEEE 802.11b

Power level at which the measurement has been performed

93.33

mW

TRANSMITTER PEAK POWER
TEST CONDITION

Channel 1

Channel 7

Channel 13

Tx Peak

Tx Ave.

Cable Loss

(dBm)

(dBm)

(dB)

25 {C

10.93

8.82

0 {C

12.10

9.75

35 {C

10.52

8.41

25 {C

11.13

9.07

0 {C

12.10

9.92

35 {C

10.41

8.35

25 {C

10.80

8.74

0 {C

11.92

9.58

35 {C

9.98

7.96

Limit

5.80

5.80

5.80

Tx Peak : 23dBm / -7dBW
Tx Ave. : 20dBm / -10dBW

NOTE:
(1) The E.U.T is a stand-alone radio device (see the clause 6.2.2). The powered by the adaptor. So,
the AC power is used as the extreme voltage source. (See clause 6.3.2.1)
(2) The value of table is worst case during test condition, includes different combinations of
transmitter rate antenna polarity and temperature
(3) TX PEAK: Max Peak Power, TX Ave.: Average Peak.
Actually Power = Max Peak Power + Cable Loss,
E.I.R.P. = Actually Power + Antenna Gain
= 17.90 dBm + 1.80dBi
= 19.70 dBm
(4) ETSI (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 12/38

2.2

Test Result of Effective Radiated Power for IEEE 802.11g

Power level at which the measurement has been performed

94.62 mW

TRANSMITTER PEAK POWER
TEST CONDITION

Channel 1

Channel 7

Channel 13

Tx Peak

Tx Ave.

Cable Loss

(dBm)

(dBm)

(dB)

25 {C

11.04

1.78

0 {C

12.16

2.98

35 {C

10.44

1.01

25 {C

10.88

1.60

0 {C

12.05

2.84

35 {C

10.12

0.73

25 {C

11.19

1.66

0 {C

12.14

2.71

35 {C

10.33

0.63

Limit

Tx Peak : 23dBm / -7dBW
Tx Ave. : 20dBm / -10dBW

NOTE:
(1) TX PEAK: Max Peak Power, TX Ave.: Average Peak.
Actually Power = Max Peak Power + Cable Loss,
E.I.R.P. = Actually Power + Antenna Gain
= 17.96 dBm + 1.80 dBi
= 19.76 dBm

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

5.80

5.80

5.80

Test Report -------------------------------------------------------------------------------- 13/38

2.3

Test Result of Effective Radiated Power for Super 802.11g

Power level at which the measurement has been performed

91.62 mW

TRANSMITTER PEAK POWER
TEST CONDITION

Channel 7

Tx Peak

Tx Ave.

Cable Loss

(dBm)

(dBm)

(dB)

25 {C

10.66

1.60

0 {C

12.02

3.04

35 {C

9.90

0.69

Limit

Tx Peak : 23dBm / -7dBW
Tx Ave. : 20dBm / -10dBW

NOTE:
(1) TX PEAK: Max Peak Power, TX Ave.: Average Peak.
Actually Power = Max Peak Power + Cable Loss,
E.I.R.P. = Actually Power + Antenna Gain
= 17.82 dBm + 1.80 dBi
= 19.62 dBm

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

5.80

Test Report -------------------------------------------------------------------------------- 14/38

III. Section 5.2.2: Peak Power Density
3.1

Test Result of Peak Power Density for IEEE 802.11b
Frequency

Ppr

CF

Ant. Gain

Ppq

Limit

Margin

(MHz)

(dBm)

(dB)

(dB)

(dBm)

(dBm)

(dB)

CH 01

2412

-2.54

6.60

1.80

5.86

10.00

-4.14

CH 07

2442

-1.79

6.60

1.80

6.61

10.00

-3.39

CH 13

2472

-2.81

6.70

1.80

5.69

10.00

-4.31

Channel

3.2

Test Result of Peak Power Density for IEEE 802.11g
Frequency

Ppr

CF

Ant. Gain

Ppq

Limit

Margin

(MHz)

(dBm)

(dB)

(dB)

(dBm)

(dBm)

(dB)

CH 01

2412

0.23

6.60

1.80

8.63

10.00

-1.37

CH 07

2442

-0.23

6.60

1.80

8.17

10.00

-1.83

CH 13

2472

-1.38

6.70

1.80

7.12

10.00

-2.88

Channel

3.3

Test Result of Peak Power Density for Super 802.11g
Channel
CH 07

Frequency

Ppr

CF

Ant. Gain

Ppq

Limit

Margin

(MHz)

(dBm)

(dB)

(dB)

(dBm)

(dBm)

(dB)

2442

-4.42

6.60

1.80

3.98

10.00

-6.02

NOTE:
(1) For equipment using FHSS modulation, the peak power density shall be limit to
–10dBW(100mW) per 100kHz E.I.R.P.
(2) For equipment using other types modulation, the peak power density shall be limit
–20dBW(10mW) per MHz E.I.R.P.
(3) Ppr: spectrum read power density (using peak search mode), CF: correct factor,
CF: Correct Factor, AG: Antenna Gain
Ppq: actual peak power density in the spread spectrum band. Ppq = Ppr + CF + AG
(4) The value of table is worst case during test condition, includes different combination s of
transmitter rate, antenna polarity and temperature
(5) The data in the above table are summarizing the following attachment spectrum analyzer hard
copy.
(6) ETSI (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 15/38

IEEE 802.11b

CH01

CH07

CH13

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 16/38

IEEE 802.11g

CH01

CH07

CH13

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 17/38

Super 802.11g

CH07

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 18/38

IV. Section 5.2.3 : Frequency Range
4.1

Test Result of Frequency Range for IEEE 802.11b

Transmitter Frequency Range – DSSS Equipment
FREQUENCY(MHz)
TEST CONDITION

Lowest Channel

Highest Channel

Channel 1

Channel 13

Frequency Rate (Mbps) Frequency Rate (Mbps)
0к
˅ˈк
35к

207 V

2402.70

11

2482.10

11

253 V

2402.80

11

2482.10

11

230 V

2402.30

11

2482.60

11

207 V

2402.30

11

2482.50

11

253 V

2402.30

11

2482.50

11

Measured frequencies
(lowest and highest)

FL = 2402.30 MHz

FH = 2482.60 MHz

Limit

FL > 2400MHz

FH < 2483.5MHz

Note:
(1) The E.U.T is a stand-alone radio device (see the clause 6.2.2). This is powered by the main. So,
the AC power is used as the extreme voltage source. (see clause 6.3.2.1).
(2) B: Battery, AC: AC Source, Rate: Transmitter Rate.
(3) The value of table is worst case during test condition, includes different combinations of
transmitter rate, antenna polarity and temperature.
(4) The data in the above table are summarizing the following attachment spectrum analyzer hard
copy.
(5) ETSI (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 19/38

Channel 1 (The lowest one in the frequency range)

Channel 13 (The greatest one in the frequency range)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 20/38

4.2

Test Result of Frequency Range for IEEE 802.11g

Transmitter Frequency Range – DSSS Equipment
FREQUENCY(MHz)
TEST CONDITION

Lowest Channel

Highest Channel

Channel 1

Channel 13

Frequency Rate (Mbps) Frequency Rate (Mbps)
0к
˅ˈк
35к

207 V

2403.60

54

2481.20

54

253 V

2403.70

54

2481.20

54

230 V

2402.80

54

2481.90

54

207 V

2402.80

54

2481.80

54

253 V

2402.90

54

2481.80

54

Measured frequencies
(lowest and highest)

FL = 2402.80 MHz

FH = 2481.90 MHz

Limit

FL > 2400MHz

FH < 2483.5MHz

Note:
(1) The E.U.T is a stand-alone radio device (see the clause 6.2.2). This is powered by the main. So,
the AC power is used as the extreme voltage source. (see clause 6.3.2.1).
(2) B: Battery, AC: AC Source, Rate: Transmitter Rate.
(3) The value of table is worst case during test condition, includes different combinations of
transmitter rate, antenna polarity and temperature.
(4) The data in the above table are summarizing the following attachment spectrum analyzer hard
copy.
(5) ETSI (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 21/38

Channel 1 (The lowest one in the frequency range)

Channel 13 (The greatest one in the frequency range)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 22/38

4.3

Test Result of Frequency Range for Super 802.11g

Transmitter Frequency Range – DSSS Equipment
FREQUENCY(MHz)
TEST CONDITION

Lowest Frequency

Highest Frequency

Channel 7

Channel 7

Frequency Rate (Mbps) Frequency Rate (Mbps)
0к
˅ˈк
35к

207 V

2425.10

108

2459.70

108

253 V

2425.10

108

2459.70

108

230 V

2424.10

108

2460.30

108

207 V

2424.60

108

2460.20

108

253 V

2424.50

108

2460.20

108

Measured frequencies
(lowest and highest)

FL = 2424.10 MHz

FH = 2459.70 MHz

Limit

FL > 2400MHz

FH < 2483.5MHz

Note:
(6) The E.U.T is a stand-alone radio device (see the clause 6.2.2). This is powered by the main. So,
the AC power is used as the extreme voltage source. (see clause 6.3.2.1).
(7) B: Battery, AC: AC Source, Rate: Transmitter Rate.
(8) The value of table is worst case during test condition, includes different combinations of
transmitter rate, antenna polarity and temperature.
(9) The data in the above table are summarizing the following attachment spectrum analyzer hard
copy.
(10) ETSI (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 23/38

Channel 1 (The lowest one in the frequency range)

Channel 13 (The greatest one in the frequency range)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 24/38

V.

Section 5.2.4: Transmitter Spurious Emissions (Radiated)
5.1

Test Result for IEEE 802.11b

Channel 1 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

302.81

H

-75.98

-36.00

-39.98

11

436.19

H

-67.80

-36.00

-31.80

11

502.87

H

-67.46

-36.00

-31.46

11

564.71

H

-64.01

-36.00

-28.01

11

598.66

H

-63.42

-36.00

-27.42

11

700.51

H

-66.12

-36.00

-30.12

11

367.07

V

-71.12

-36.00

-35.12

11

437.40

V

-71.30

-36.00

-35.30

11

468.92

V

-70.49

-36.00

-34.49

11

500.45

V

-64.31

-36.00

-28.31

11

564.71

V

-66.79

-36.00

-30.79

11

598.66

V

-61.24

-36.00

-25.24

11

Note:
(1) A. P. means antenna polarization, horizontal and vertical.
Amplitude means the fundamental emission measured
C F. means Correct Factor, Rate means transmitter rate
Corrected Factor (C. F.) = Cable Loss + Antenna Factor – Amplified Gain
LEVEL = Amplitude + Corrected Factor
(2) The margin is minus that means under limit.
(3) The value of table is the worst case during test condition. This is including different
combinations of transmitter rate antenna polarity and temperature.
(4) ETSI (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 25/38

Channel 13 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

339.19

H

-66.11

-36.00

-30.11

11

386.47

H

-71.27

-36.00

-35.27

11

436.19

H

-67.34

-36.00

-31.34

11

502.87

H

-68.16

-36.00

-32.16

11

564.71

H

-64.38

-36.00

-28.38

11

598.66

H

-63.60

-36.00

-27.60

11

369.50

V

-71.31

-36.00

-35.31

11

434.97

V

-70.60

-36.00

-34.60

11

468.92

V

-70.56

-36.00

-34.56

11

501.66

V

-63.92

-36.00

-27.92

11

564.71

V

-66.81

-36.00

-30.81

11

598.66

V

-60.79

-36.00

-24.79

11

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 26/38

Channel 1 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

2158.33

H

-52.58

-30.00

-22.58

11

2637.50

H

-55.03

-30.00

-25.03

11

7234.69

H

-59.19

-30.00

-29.19

11

9647.40

H

-56.41

-30.00

-26.41

11

12060.10

H

-57.37

-30.00

-27.37

11

2362.50

V

-52.21

-30.00

-22.21

11

2639.58

V

-50.36

-30.00

-20.36

11

7234.69

V

-60.03

-30.00

-30.03

11

9647.40

V

-58.74

-30.00

-28.74

11

12060.10

V

-57.04

-30.00

-27.04

11

Channel 13 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

2158.33

H

-54.42

-30.00

-24.42

11

2637.50

H

-55.37

-30.00

-25.37

11

7415.83

H

-59.30

-30.00

-29.30

11

9886.35

H

-57.01

-30.00

-27.01

11

12360.73

H

-57.69

-30.00

-27.69

11

1820.83

V

-54.97

-47.00

-7.97

11

2637.50

V

-52.20

-30.00

-22.20

11

4945.31

V

-63.16

-30.00

-33.16

11

7415.83

V

-59.96

-30.00

-29.96

11

9886.35

V

-58.01

-30.00

-28.01

11

12360.73

V

-58.36

-30.00

-28.36

11

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 27/38

5.2

Test Result for IEEE 802.11g

Channel 1 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

434.97

H

-67.17

-36.00

-31.17

54

500.45

H

-69.21

-36.00

-33.21

54

564.71

H

-64.64

-36.00

-28.64

54

598.66

H

-64.41

-36.00

-28.41

54

698.09

H

-66.84

-36.00

-30.84

54

369.50

V

-71.04

-36.00

-35.04

54

434.97

V

-71.07

-36.00

-35.07

54

468.92

V

-70.56

-36.00

-34.56

54

501.66

V

-64.43

-36.00

-28.43

54

565.92

V

-66.01

-36.00

-30.01

54

597.45

V

-60.32

-36.00

-24.32

54

Channel 13 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

436.19

H

-66.76

-36.00

-30.76

54

501.66

H

-69.37

-36.00

-33.37

54

564.71

H

-64.82

-36.00

-28.82

54

598.66

H

-64.30

-36.00

-28.30

54

699.30

H

-66.71

-36.00

-30.71

54

369.50

V

-71.36

-36.00

-35.36

54

468.92

V

-70.72

-36.00

-34.72

54

501.66

V

-64.24

-36.00

-28.24

54

565.92

V

-66.39

-36.00

-30.39

54

597.45

V

-60.81

-36.00

-24.81

54

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 28/38

Channel 1 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

2158.33

H

-52.25

-30.00

-22.25

54

2637.50

H

-53.53

-30.00

-23.53

54

7234.69

H

-59.69

-30.00

-29.69

54

9647.40

H

-58.74

-30.00

-28.74

54

12060.10

H

-56.71

-30.00

-26.71

54

2237.50

V

-55.76

-30.00

-25.76

54

2639.58

V

-49.86

-30.00

-19.86

54

7234.69

V

-61.03

-30.00

-31.03

54

9647.40

V

-58.91

-30.00

-28.91

54

12060.10

V

-57.21

-30.00

-27.21

54

Channel 13 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

2158.33

H

-52.75

-30.00

-22.75

54

2637.50

H

-54.20

-30.00

-24.20

54

4945.31

H

-61.66

-30.00

-31.66

54

7415.83

H

-59.63

-30.00

-29.63

54

9886.35

H

-58.01

-30.00

-28.01

54

12360.73

H

-57.86

-30.00

-27.86

54

2358.33

V

-53.41

-30.00

-23.41

54

2637.50

V

-50.20

-30.00

-20.20

54

7415.83

V

-59.80

-30.00

-29.80

54

9886.35

V

-57.01

-30.00

-27.01

54

12360.73

V

-57.69

-30.00

-27.69

54

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 29/38

5.3

Test Result for Super 802.11g

Channel 7 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

301.60

H

-74.70

-36.00

-38.70

108

434.97

H

-68.63

-36.00

-32.63

108

500.45

H

-69.49

-36.00

-33.49

108

565.92

H

-64.69

-36.00

-28.69

108

598.66

H

-64.62

-36.00

-28.62

108

287.05

V

-74.68

-36.00

-38.68

108

401.02

V

-72.83

-36.00

-36.83

108

434.97

V

-70.43

-36.00

-34.43

108

531.98

V

-67.20

-36.00

-31.20

108

598.66

V

-66.19

-36.00

-30.19

108

700.51

V

-66.78

-36.00

-30.78

108

Channel 7 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

2237.50

H

-54.09

-30.00

-24.09

108

2518.75

H

-56.35

-30.00

-26.35

108

7327.19

H

-58.62

-30.00

-28.62

108

9766.87

H

-57.91

-30.00

-27.91

108

12210.42

H

-56.43

-30.00

-26.43

108

1820.83

V

-58.31

-30.00

-28.31

108

2518.75

V

-52.68

-30.00

-22.68

108

7327.19

V

-60.95

-30.00

-30.95

108

9766.87

V

-58.41

-30.00

-28.41

108

12210.42

V

-55.43

-30.00

-25.43

108

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 30/38

VI. Section 5.3.2: Receiver Spurious Emissions (Radiated)
6.1

Test Result for IEEE 802.11b

Channel 1 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

403.45

H

-71.81

-57.00

-14.81

11

433.76

H

-65.07

-57.00

-8.07

11

501.66

H

-63.05

-57.00

-6.05

11

564.71

H

-63.57

-57.00

-6.57

11

597.45

H

-62.20

-57.00

-5.20

11

631.40

H

-67.21

-57.00

-10.21

11

302.81

V

-72.75

-57.00

-15.75

11

369.50

V

-70.81

-57.00

-13.81

11

436.19

V

-70.26

-57.00

-13.26

11

502.87

V

-63.93

-57.00

-6.93

11

564.71

V

-65.71

-57.00

-8.71

11

598.66

V

-60.32

-57.00

-3.32

11

Note:
(1) A. P. means antenna polarization, horizontal and vertical.
Amplitude means the fundamental emission measured.
C F. means Correct Factor, Rate means transmitter rate
Corrected Factor (C. F.) = Cable Loss + Antenna Factor – Amplified Gain
LEVEL = Amplitude + Corrected Factor
(2) The value of table is worst case during test condition, includes different combinations of
transmitter rate antenna polarity and temperature
(3) ETSI (2400MHz ~ 2483.5MHz),
FRANCE outdoor use limited to 10mW e.i.r.p. within the band (2454MHz ~ 2483.5MHz)

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 31/38

Channel 13 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

401.02

H

-72.24

-57.00

-15.24

11

434.97

H

-64.62

-57.00

-7.62

11

500.45

H

-62.50

-57.00

-5.50

11

564.71

H

-63.02

-57.00

-6.02

11

598.66

H

-62.49

-57.00

-5.49

11

700.51

H

-67.21

-57.00

-10.21

11

369.50

V

-71.48

-57.00

-14.48

11

436.19

V

-70.31

-57.00

-13.31

11

468.92

V

-69.45

-57.00

-12.45

11

504.09

V

-64.03

-57.00

-7.03

11

564.71

V

-66.22

-57.00

-9.22

11

598.66

V

-59.74

-57.00

-2.74

11

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 32/38

Channel 1 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

1499.37

H

-63.82

-47.00

-16.82

11

3957.08

H

-62.36

-47.00

-15.36

11

5670.62

H

-60.95

-47.00

-13.95

11

9964.27

H

-56.36

-47.00

-9.36

11

2096.67

V

-59.48

-47.00

-12.48

11

3942.40

V

-62.43

-47.00

-15.43

11

5611.87

V

-60.23

-47.00

-13.23

11

9425.73

V

-57.28

-47.00

-10.28

11

Channel 13 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

1499.37

H

-63.15

-47.00

-16.15

11

3315.73

H

-63.58

-47.00

-16.58

11

5176.15

H

-60.86

-47.00

-13.86

11

9734.17

H

-58.32

-47.00

-11.32

11

1499.37

V

-59.32

-47.00

-12.32

11

3315.73

V

-61.98

-47.00

-14.98

11

5176.15

V

-58.62

-47.00

-11.62

11

9734.17

V

-56.82

-47.00

-9.82

11

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 33/38

6.2

Test Result for IEEE 802.11g

Channel 1 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

402.24

H

-72.16

-57.00

-15.16

54

434.97

H

-63.76

-57.00

-6.76

54

501.66

H

-62.79

-57.00

-5.79

54

564.71

H

-63.09

-57.00

-6.09

54

598.66

H

-62.24

-57.00

-5.24

54

632.61

H

-67.30

-57.00

-10.30

54

331.91

V

-69.91

-57.00

-12.91

54

434.97

V

-70.63

-57.00

-13.63

54

501.66

V

-64.39

-57.00

-7.39

54

565.92

V

-66.48

-57.00

-9.48

54

598.66

V

-60.25

-57.00

-3.25

54

Channel 13 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

437.40

H

-63.94

-57.00

-6.94

54

500.45

H

-63.00

-57.00

-6.00

54

531.98

H

-68.24

-57.00

-11.24

54

565.92

H

-63.65

-57.00

-6.65

54

597.45

H

-62.47

-57.00

-5.47

54

369.50

V

-70.58

-57.00

-13.58

54

436.19

V

-70.24

-57.00

-13.24

54

501.66

V

-64.08

-57.00

-7.08

54

565.92

V

-66.32

-57.00

-9.32

54

598.66

V

-60.18

-57.00

-3.18

54

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 34/38

Channel 1 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

1499.37

H

-62.82

-47.00

-15.82

11

2096.67

H

-65.98

-47.00

-18.98

11

3991.35

H

-61.36

-47.00

-14.36

11

9533.44

H

-56.36

-47.00

-9.36

11

1499.37

V

-57.99

-47.00

-10.99

11

2096.67

V

-59.32

-47.00

-12.32

11

5043.96

V

-61.49

-47.00

-14.49

11

9753.75

V

-56.29

-47.00

-9.29

11

Channel 13 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

1499.37

H

-65.49

-47.00

-18.49

11

2738.02

H

-65.31

-47.00

-18.31

11

5695.10

H

-60.58

-47.00

-13.58

11

9504.06

H

-56.94

-47.00

-9.94

11

1499.37

V

-57.15

-47.00

-10.15

11

2096.67

V

-59.32

-47.00

-12.32

11

4941.15

V

-60.84

-47.00

-13.84

11

8999.79

V

-58.29

-47.00

-11.29

11

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 35/38

6.3

Test Result for Super 802.11g

Channel 7 (30MHz to 1GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

142.76

H

-76.10

-57.00

-19.10

108

301.60

H

-77.07

-57.00

-20.07

108

434.97

H

-69.16

-57.00

-12.16

108

501.66

H

-68.59

-57.00

-11.59

108

565.92

H

-64.23

-57.00

-7.23

108

598.66

H

-60.33

-57.00

-3.33

108

214.30

V

-75.58

-57.00

-18.58

108

313.72

V

-70.86

-57.00

-13.86

108

434.97

V

-73.98

-57.00

-16.98

108

500.45

V

-69.01

-57.00

-12.01

108

598.66

V

-63.30

-57.00

-6.30

108

850.86

V

-64.52

-57.00

-7.52

108

Channel 7 (1GHz to 12.75GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

1592.40

H

-63.86

-47.00

-16.86

108

3203.12

H

-63.03

-47.00

-16.03

108

4843.23

H

-61.14

-47.00

-14.14

108

9504.06

H

-58.44

-47.00

-11.44

108

1499.37

V

-57.65

-47.00

-10.65

108

2096.67

V

-60.32

-47.00

-13.32

108

4711.04

V

-61.41

-47.00

-14.41

108

8285.00

V

-58.04

-47.00

-11.04

108

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 36/38

6.4

Test Result for Standby mode

(30MHz to 12.5GHz)
Frequency

A. P.

LEVEL

Limit

Margin

Rate

(MHz)

(H/V)

(dBm)

(dBm)

(dB)

(Mbps)

168.22

H

-77.06

-57.00

-20.06

---

234.91

H

-74.83

-57.00

-17.83

---

369.50

H

-73.91

-57.00

-16.91

---

402.24

H

-72.37

-57.00

-15.37

---

434.97

H

-64.39

-57.00

-7.39

---

501.66

H

-62.96

-57.00

-5.96

---

564.71

H

-63.30

-57.00

-6.30

---

598.66

H

-62.35

-57.00

-5.35

---

1592.40

H

-65.69

-47.00

-18.69

---

3070.94

H

-63.95

-47.00

-16.95

---

3991.35

H

-62.20

-47.00

-15.20

---

8363.33

H

-59.85

-47.00

-12.85

---

301.60

V

-72.14

-57.00

-15.14

---

328.27

V

-66.98

-57.00

-9.98

---

365.86

V

-71.04

-57.00

-14.04

---

436.19

V

-70.21

-57.00

-13.21

---

502.87

V

-64.33

-57.00

-7.33

---

567.14

V

-66.82

-57.00

-9.82

---

598.66

V

-61.22

-57.00

-4.22

---

1499.37

V

-57.99

-47.00

-10.99

---

2096.67

V

-58.82

-47.00

-11.82

---

3971.77

V

-60.29

-47.00

-13.29

---

8363.33

V

-58.18

-47.00

-11.18

---

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 37/38

VII. Instrument and Ancillaries Equipment of List
Calibration Date

Instrument Name

Model

Brand

Serial No.

Next time

EMI Receiver

8546A

HP

3520A00242

08/05/05

RF Filter Section

85460A

HP

3448A00217

08/05/05

Small Biconical

UBAA9114 &

SCHWARZECK

127

10/11/05

Antenna

BBVU9135

Pre-amplifier

PA1F

TRC

1FAC

05/20/05

Auto Switch Box

ASB-01

TRC

9904-01

05/20/05

A30A30-0058-50FS-15M

JYEBAO

SMA-01

05/20/05

A30A30-0058-50FS-1M

JYEBAO

SMA-02

05/20/05

Spectrum Analyzer

8564E

HP

3720A00840

08/13/05

Microwave

84125C

HP

US36433002

08/13/05

Horn Antenna

3115

EMCO

9104-3668

12/18/04

Standard Guide

84125-80008

HP

18-26.5GHz

12/18/04

84125-80001

HP

26.5-40GHz

12/18/04

Horn Antenna

1196E (3115)

HP (EMCO)

9704-5178

12/12/04

Pre-amplifier

PA2F

TRC

2F1GZ

03/20/05

Coaxial Cable

A30A30-0058-50FST118

JYEBAO

MSA-05

03/20/05

A30A30-0058-50FST118

JYEBAO

MSA-04

03/20/05

(?30MHz)
Coaxial Cable
(Double shielded,
15 meter)
Coaxial Cable
(1.1 meter)

Preamplifier

Horn Antenna
Standard Guide
Horn Antenna

(3 miter)
Coaxial Cable
(1 meter)
The level of confidence of 95% , the uncertainty of measurement of radiated emission is +3.05dB / -3.84dB .

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report -------------------------------------------------------------------------------- 38/38

Appendix A

Antenna Specification

Report No.: C51ET050304 (ETSI EN 300 328)
Training Research Co., Ltd., TEL:886-2-26935155, Fax:886-2-26934440

Test Report ------------------------------------------------------------------------------- 1/45
Report No.

C51ET050304

Specifications

ETSI EN 301 489-1 V1.4.1 (August, 2002)
ETSI EN 301 489-17 V1.2.1 (April, 2002)

Applicant

CAMEO COMMUNICATIONS, INC.

Applicant
address

No. 42, Min Chuan East Road, Section 6,
Taipei 114, Taiwan

Items tested
Model No.

802.11g Wireless PCI Adapter
W LG-1202, WNC- 0300, LWS5410P, NWP-0108G,
ALL0281A

EUT Condition

Engineering sample;
(Sample # N10415)

Results
Date

Compliance (As detailed within this report)
12/01/2004 (month / day / year) (Sample received)
12/14/2004 (month / day / year) (Test)

Pre-production;

Prepared by
______________________
Authorized by
Issue date

December 16, 2004

Final production

Project Engineer
(Jack Tsai)
General Manager
(Frank Tsai)
(month / day / year)

Modifications
Tested by

None
Training Research Co., Ltd.

Office at

No. 255, Nan Yang Street, Shijr City, Taipei Hsien 221, Taiwan

Laboratory at

1F, No. 255, Nan Yang Street, Shijr City, Taipei Hsien 221, Taiwan

Open site at

No. 15, Lane 530, Balian Rd., Sec. 1, Shijr City, Taipei Hsien 221, Taiwan

Conditions of issue:
This test report shall not be reproduced except in full, without written approval of
TRC. And the test result contained within this report only relate to the sample
submitted for testing.

Ϫʳ Aut. No. ELA 131
Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 2/45

Generally Statement:
The results appear in the following order:
Electromagnetic compatibility and radio spectrum matters (ERM); Electro Magnetic
Compatibility (EMC) standard for radio equipment and services;
Part 1: Common Technical requirements
Part 17: Specific conditions for Wideband data and HIPERLAN equipment.
The results exhibits below only apply to particular samples tested and to the specific tests
carried out, as detailed in this Test Report. The issue of this Test Report does not indicate any
measure of Approval, Certification, Supervision, Control or Surveillance by Training Research
Co., Ltd. of any product. No extract, abridgement or abstraction from a Test Report may be
published or used to advertise a product without the written consent of the Director, Training
Research Co., Ltd. who reserves the absolute right to agree or reject all or any of the details of
any item of publicity for which consent may be sought.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 3/45

Contents
CHAPTER 0

EMISSION AND SUSCEPTIBILITY STANDARDS........5
EMISSION STANDARDS...............................................................................5
SUSCEPTIBILITY STANDARDS.....................................................................5

CHAPTER 1

INTRODUCTION..............................................................6
DESCRIPTION OF EUT ................................................................................6
TEST METHOD ...........................................................................................6
LIST OF SUPPORT EQUIPMENT ....................................................................7

CHAPTER 2

EMISSION AND IMMUNITY REQUIREMENTS
OVERVIEW ...................................................................10
EMISSION (ETSI EN 301 489-1) ..............................................................10
IMMUNITY (ETSI EN 301 489-1).............................................................11

CHAPTER 3

PERFORMANCE CRITERIA.........................................12
ETSI EN 301 489-17, SUBCLAUSE 6.2 ....................................................12

CHAPTER 4

ELECTROSTATIC DISCHARGES IMMUNITY TEST 18
ESD TEST INFORMATION:........................................................................18
EN 61000-4-2 PHOTO OF TESTSET-UP .............................................20

CHAPTER 5

RADIO FREQUENCY IMMUNITY TEST (RS).............21
RS TEST INFORMATION:...........................................................................21
EN 61000-4-3 PHOTO OF TESTSET-UP .............................................23

CHAPTER 6

ELECTRIC FAST TRANSIENT/
BURST REQUIREMENTS TEST..................................24
EFT TEST INFORMATION: ........................................................................24
EN 61000-4-4 PHOTO OF TESTSET-UP .............................................26

CHAPTER 7

SURGE IMMUNITY TEST.............................................27
SURGE TEST INFORMATION:.....................................................................27
EN 61000-4-5 PHOTO OF TESTSET-UP .............................................29

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 4/45

CHAPTER 8

CONTINUOUS WAVE VOLTAGE IMMUNITY TEST 30
CS TEST INFORMATION:...........................................................................30
TEST INSTRUMENTS : ................................................................................32
EN 61000-4-6 PHOTO OF TESTSET-UP .............................................33

CHAPTER 9

VOLTAGE DIP / INTERRUPTION TEST.....................34
DIP TEST INFORMATION :.........................................................................34
EN 61000-4-11 PHOTO OF TESTSET-UP ...........................................35

CHAPTER 10 HARMONICS TEST........................................................36
CHAPTER 11

VOLTAGE FLUCTUATION AND FLICKER TEST.....37

CHAPTER 12 CONDUCTED EMISSION TEST....................................38
TEST CONDITION AND SETUP ....................................................................38
LIST OF TEST INSTRUMENT ......................................................................39
CONDUCTED TEST P LACEMENT (F RONT VIEW AND SIDE VIEW )...............40
TEST RESULT OF CONDUCTED EMISSIONS FOR MAINS POWER .................41

CHAPTER 13 RADIATED EMISSION TEST........................................42
TEST CONDITION AND SETUP ....................................................................42
LIST OF TEST INSTRUMENT ......................................................................43
RADIATED TEST PLACEMENT (FRONT VIEW AND REAR VIEW ).................44
TEST RESULT OF SPURIOUS RADIATED EMISSIONS FOR 30MHZ TO 1GHZ
[HORIZONTAL].........................................................................................45
TEST RESULT OF SPURIOUS RADIATED EMISSIONS FOR 30MHZ TO 1GHZ
[V ERTICAL] .............................................................................................45

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 5/45

Chapter 0

Emission and Susceptibility Standards

Emission Standards
Emission Standard

European Standard

International Standard

(

)

EN 61000-6-3/2001

IEC 61000-6-3/1996

(

)

EN 61000-6-4/2001

IEC 61000-6-4/1997

(

)

EN 50081-1/1992

(

)

EN 50081-1/8.93

(

)

EN 55014/4.93

CISPR 14: 1993

(

)

EN 55015/12.93

CISPR 15: 1992

(

)

EN 55011/91

CISPR 11: 1990

(X)

EN 55022/98

CISPR 22: 1997

(X)

EN 61000-3-2/2000

IEC 61000-3-2: 2000

(X)

EN 61000-3-3/1995

IEC 61000-3-3: 1994

+A1/2001

+A1/2001

Susceptibility Standards
Susceptibility Standard European Standard

International Standard

(

)

EN 61000-6-1/2001

IEC 61000-6-1/1997

(

)

EN 61000-6-2/2001

IEC 61000-6-2/1999

(

)

EN 50082-1/1997

(

)

EN 50082-2/1994

(

)

EN 55024/1998

CISPR 24/1997

(

)

EN 55020/2002

CISPR 20/2002

(X)

EN 61000-4-2:1995

IEC 61000-4-2:1995

(X)

EN 61000-4-3:1996

IEC 61000-4-3:1995

(X)

EN 61000-4-4:1995

IEC 61000-4-4:1995

(X)

EN 61000-4-5:1995

IEC 61000-4-5:1995

(X)

EN 61000-4-6:1996

IEC 61000-4-6:1996

(

EN 61000-4-8:1993

IEC 61000-4-8:1993

(X)

EN 61000-4-11:1994

IEC 61000-4-11:1994

(

EN 55014-2:1993

CISPR/F (Sec) 159

)
)

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 6/45

Chapter 1

Introduction

Description of EUT
Product Name

:

802.11g Wireless PCI Adapter

Model Name

:

W LG-1202, WNC- 0300,
LWS5410P, NWP-0108G,
ALL0281A

Frequency Range

:

2.400GHz ~ 2.4835GHz

Operating Frequency :

2.412GHz ~ 2.472GHz

Support Channel

:

13 Channels

Modulation Skill

:

DBPSK, DQPSK, CCK, OFDM

Power Type

:

Power by PCI of client’ s device

Power Cable

:

None

Data Cable

:

None

Test Method
1. Put the EUT into a personal computer’ s PCI bus and fix it.
2. Using the notebook computer and software provided by the manufacturer to control
EUT, the test is performed under the specific conditions.
3. Then making EUT to the following mode.
(a) EMI testing: During test, making EUT to the linking mode with support equipments
(b) EMS testing: same as above

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 7/45

List of Support Equipment
In order to construct the minimum testing, following equipment were used as the support
units.
PC
Model No.

:
:

IBM 6840; HP Pavilion; HP d330 uT
6840MJV; P8574A; d338 uT

Serial No.

:

96CC 0C1; TW21920435; SGH41508NP

FCC ID
ᛀ጖

:
:

N/A, DoC
3892I279; 3902H097, R33001

Power type
Power cord

:
:

100 ~ 127VAC / 4A, 200 ~ 240VAC/2A, 50 ~ 60Hz, 5A, Switching
Non-shielded, 2.33 m length, Plastic hood, No ferrite core

Fax/Modem
Model No.
Serial No.
FCC ID
Power type
Power Cord
Data Cable

:
:
:
:
:
:
:

Aceex
DM-1414
9010582
IFAXDM1414
110 VAC / 50 ~ 60 Hz, Switching
Non-shielded, 1.90m long, Plastic hoods, and no ferrite bead
RS-232ШShielded, 1.30m long, Metal hoods , No bead
RJ-11Cx2ШNon-shielded, 7’ long, Plastic hoods, No bead

Printer
Model No.
Serial No.
FCC ID
ᛀ጖

:
:
:
:
:

Power type
Power cord

:
:

Data cable

:

HP
C6464A, C2642A
TH16LEB5PK, SG69A196GV
None (DoC Approved), B94C2642X

3892H381, None
Switching adaptor
Non-shielded, 173cm length, No ferrite core
(between adaptor and AC source)
Non-shielded, 180cm length, with ferrite core
(between printer and adaptor)
Shielded, 1.70m length, No ferrite core

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 8/45

Monitor

:

HP 15’ Color Monitor, HP pavilion mx70

Model No.
Serial No.

:
:

D2827A, P1283A
KR91379759, TWTBQ00397

FCC ID

:

C5F7NFCMC1518X

BSMI

:

3872B039

Power type

:

110 ~ 240 VAC / 50 ~ 60 Hz, Switching

Power cord
Data cable

:
:

Shielded, 1.83m length, No ferrite core
Shielded, 1.46m length, with two ferrite cores

USB Gamepad
Model No.
Serial No.
FCC ID
BSMI
Power type
Data Cable

:
:
:
:
:
:
:

Rockfire
QF-337uv
10600545, KR91379759
None (CE approval)
3862A574
By computer
Shielded, 1.81m long, Plastic, with ferrite core

PS/2 Keyboard
Model No.
Serial No.
FCC ID
BSMI
Power type
Data cable

:
:
:
:
:
:
:

HP
5187-0343, SK-2501K
BE21700404, M981216213
DoC Approved, GYUR38SK
3892C981, 3862A621
By PC
Shielded, 1.73m length, Plastic hood, No ferrite core

Mouse
Model No.
Serial No.
FCC ID
BSMI
Power type
Power cord

:
:
:
:
:
:
:

HP
M-UR89, M-S34
LZS21750238, LZC84446151
DoC Approved, DZL211029
3892D767, 4862A011
By PC
Shielded, 1.80m length, No ferrite core

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 9/45

Notebook

:

ASUS

Model No.
FCC ID

:
:

M2400E
N/A, DoC Approved

Adaptor

:

DELTA ELECTRONICS, INC.

Model No.

:

ADP-65DB REV.B

Serial No.

:

Q3W0311044403

FCC ID
BSMI

:
:

N/A, CE Approved
3882B596

Power type
Power cable

:
:

I/P: 100 ~ 240vac, 50 ~ 60 Hz, 1.5A ; O/P: 19Vdc, 3.42A
Non-shielded, 1.85m length, Plastic hood, No ferrite core
(Between power adaptor and AC power source)

Power cable

:

Non-Shielded, 1.70m length, with ferrite core
(Between power adaptor and notebook)

WLAN Card
Model No.
FCC ID

:
:
:

Gemtek Technology Co., Ltd.
C911003
MXF-C911003

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 10/45

Chapter 2

Emission and Immunity Requirements Overview

Emission (ETSI EN 301 489-1)
Phenomenon

Application

Equipment test requirement

Reference
Subclause in
the present

Radio and

Radio and

Radio and

ancillary

ancillary

ancillary

equipment for
fixed use (base

equipment for
vehicular use

equipment for
portable use

station

(mobile

(portable

equipment)
Applicable for
stand alone
testing

equipment)
Applicable for
stand alone
testing

equipment)
Applicable for
stand alone
testing

Applicable

Not applicable

8.3

document

Radiated
emission

Enclosure of
ancillary
equipment

Conducted
emission

DC power
input/output
port

Applicable

Conducted
emission

AC mains
input/output
port
AC mains
input port

Applicable

Not applicable Not applicable

8.4

Applicable

Not applicable Not applicable

8.5

Applicable

Not applicable Not applicable

8.6

Harmonic
current
emissions
Voltage
fluctuations
and flicker

AC mains
input port

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

8.2

Test Report ------------------------------------------------------------------------------- 11/45

Immunity (ETSI EN 301 489-1)
Phenomenon

Application

Equipment test requirement

Reference

Radio and Subclause in
the present
ancillary
equipment for equipment for equipment for document
fixed use (base vehicular use portable use
(portable
station
(mobile
equipment)
equipment) equipment)
Radio and
ancillary

Radio and
ancillary

Applicable

Applicable

Applicable

9.2

Electrostatic
Enclosure
discharge
Fast transients
Signal,
common mode telecommunication
and control ports,
DC and AC power
ports

Applicable

Applicable

Applicable

9.3

Applicable

Not
applicable

Not
applicable

9.4

RF common
Signal,
mode 0.15 MHz telecommunication
to 80MHz
and control ports,
DC and AC power
ports

Applicable

Applicable

Not
applicable

9.5

Not applicable

Applicable

9.6

Applicable

Not
applicable

Not
applicable
Not
applicable

Applicable

Not
applicable

Not
applicable

RF
electromagnetic
field ( 80MHz to
1GHz)

Enclosure

Transients and DC power input
surges
ports
Voltage dips and AC mains power
interruptions
input ports
Surges, line to AC mains power
line and line
input ports,
ground
telecommunication
ports

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

9.7
9.8

Test Report ------------------------------------------------------------------------------- 12/45

Chapter 3

Performance Criteria

ETSI EN 301 489-17, Subclause 6.2
Table 1 Performance criteria
Criteria
During test
After test
A
Shall operate as intended
Shall operate as intended

B

C

May show degradation of

Shall be no degradation of performance

performance (NOTE 1)
Shall be no loss of function
Shall be no unintentional
transmissions
May show loss of function (one or
more)
May show degradation of
performance (NOTE 1)
No unintentional transmissions

(NOTE 2)
Shall be no loss of function
Shall be no loss of stored data or user
programmable functions
Function shall be self-recoverable
Shall operate as intended after recovering
Shall be no degradation of performance
(NOTE 2)
Shall be no loss of stored data or user
programmable functions

May be loss of function (one or
more)

Functions shall be recoverable by the
operator
Shall operate as intended after recovering
Shall be no degradation of performance
(NOTE 2)

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 13/45

NOTE 1:
Degradation of performance during the test is understood as a degradation to a level not
below a minimum performance level specified by the manufacturer for the use of the apparatus
as intended. In some cases the specified minimum performance level may be replaced by a
permissible degradation of performance.
If the minimum performance level or the permissible performance degradation in not
specified by the manufacturer then either of these may be derived from the product description
and documentation (including leaflets and advertising) and what the user may reasonably expect
form the apparatus if used as intended.

NOTE 2:
No degradation of performance after the test is understood as no degradation below a
minimum performance level specified by the manufacturer for the use of the apparatus as
intended. In some cases the specified minimum performance level may be replaced by a
permissible degradation of performance. After the test no change of actual operating data or user
retrievable data is allowed.
If the minimum performance level or the permissible performance degradation in not
specified by the manufacturer then either of these may be derived from the product description
and documentation (including leaflets and advertising) and what the user may reasonably expect
form the apparatus if used as intended.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 14/45

ETSI EN 301 489-1
Performance criteria for Continuous phenomena applied Transmitters (CT)
If no further details are given in the relevant part of the present document dealing with the
particular type of radio equipment, the following general performance criteria for continuous
phenomena shall apply.
During and after the test:
The apparatus shall continue to operate as intended. No degradation of performance or loss
of function is allowed below a permissible performance level specified by the manufacturer
when the apparatus is used as intends. In some cases this permissible performance level may
be replaced by a permissible loss of performance.
During the test:
The EUT shall not unintentionally transmit or change its actual operating state and stored
data. If the minimum performance level or the permissible loss is not specified by the
manufacturer, then either of these may be deduced from the product description and
documentation and what the user may reasonably expect form the apparatus if used as
intended.
For ancillary equipment the pass/failure criteria supplied by the manufacturer (see subclause
6.4) shall apply, unless the ancillary equipment is tested in connection with a receiver or
transmitter in which case the corresponding performance criteria above shall apply.

Performance criteria for Transient phenomena applied Transmitters (TT)
If no further details are given in the relevant part of the present document dealing with the
particular type of radio equipment, the following general performance criteria for transient
phenomena shall apply.
After the test:
The apparatus shall continue to operate as intended. No degradation of performance or loss
of function is allowed below a permissible performance level specified by the manufacturer
when the apparatus is used as intends. In some cases this permissible performance level may
be replaced by a permissible loss of performance.
During the test:
The EMC exposure to an electromagnetic phenomenon, a degradation of performance is,
however, allowed. No change of the actual mode of operation (e.g. unintended transmission)
or stored data is allowed.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 15/45

If the minimum performance level or the permissible loss is not specified by the
manufacturer, Then either of these may be deduced from the product description and
documentation and what the user may reasonably expect form the apparatus if used as
intended.
For ancillary equipment the pass/failure criteria supplied by the manufacturer (see subclause
6.4) shall apply, unless the ancillary equipment is tested in connection with a receiver or
transmitter in which case the corresponding performance criteria above shall apply.

Performance criteria for Continuous phenomena applied Receivers (CR)
If no further details are given in the relevant part of the present document dealing with the
particular type of radio equipment, the following general performance criteria for continuous
phenomena shall apply.
During and after the test:
The apparatus shall continue to operate as intended. No degradation of performance or loss
of function is allowed below a permissible performance level specified by the manufacturer
when the apparatus is used as intends. In some cases this permissible performance level may
be replaced by a permissible loss of performance.
During the test:
The EUT shall not unintentionally transmit or change its actual operating state and stored
data. If the minimum performance level or the permissible loss is not specified by the
manufacturer, then either of these may be deduced from the product description and
documentation and what the user may reasonably expect form the apparatus if used as
intended.
For ancillary equipment the pass/failure criteria supplied by the manufacturer (see subclause
6.4) shall apply, unless the ancillary equipment is tested in connection with a receiver or
transmitter in which case the corresponding performance criteria above shall apply.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 16/45

Performance criteria for Transient phenomena applied Receivers (TR)
If no further details are given in the relevant part of the present document dealing with the
particular type of radio equipment, the following general performance criteria for transient
phenomena shall apply.
After the test:
The apparatus shall continue to operate as intended. No degradation of performance or loss
of function is allowed below a permissible performance level specified by the manufacturer
when the apparatus is used as intends. In some cases this permissible performance level may
be replaced by a permissible loss of performance.
During the test:
The EMC exposure to an electromagnetic phenomenon, a degradation of performance is,
however, allowed. No change of the actual mode of operation (e.g. unintended transmission)
or stored data is allowed.
If the minimum performance level or the permissible loss is not specified by the
manufacturer, then either of these may be deduced from the product description and
documentation and what the user may reasonably expect form the apparatus if used as
intended.
For ancillary equipment the pass/failure criteria supplied by the manufacturer (see subclause
6.4) shall apply, unless the ancillary equipment is tested in connection with a receiver or
transmitter in which case the corresponding performance criteria above shall apply.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 17/45

ETSI EN 301 489-17
Performance criteria for Continuous phenomena applied Transmitters (CT)
The performance criteria A shall apply.
Tests shall be repeated with the EUT in standby mode (if applicable) to ensure that
unintentional transmission does not occur. In systems using acknowledgement signals, it is
recognized that an ACKnowledgement (ACK) or Not ACKnowledgement (NACK) transmission
may occur, and steps should be taken to ensure that any transmission resulting from the
application of the test is correctly interpreted.

Performance criteria for Transient phenomena applied Transmitters (TT)
The performance criteria B shall apply, except for voltage dips of 100ms and voltage
interruptions of 5000 ms duration, for which performance criteria C shall apply.
Tests shall be repeated with the EUT in standby mode (if applicable) to ensure that unintentional
transmission does not occur. In system using acknowledgement signals, it is recognized that an
acknowledgement (ACK) or not-acknowledgement (NACK) transmission may occur, and steps
should be taken to ensure that any transmission resulting from the application of the test is
correctly interpreted.

Performance criteria for Continuous phenomena applied Receivers (CR)
The performance criteria A shall apply.
Where the EUT is a transceiver, under no circumstances, shall the transmitter operate
unintentionally during the test. In systems using acknowledgement signals, it is recognized that
an ACK or NACK transmission may occur, and steps should be taken to ensure that any
transmission resulting from the application of test is correctly interpreted.

Performance criteria for Transient phenomena applied Receivers (TR)
The performance criteria B shall apply, except for voltage dips of 100ms and voltage
interruptions of 5000 ms duration, for which performance criteria C shall apply.
Where the EUT is a transceiver, under no circumstances, shall the transmitter operate
unintentionally during the test. In systems using acknowledgement signals, it is recognized that
an ACK or NACK transmission may occur, and steps should be taken to ensure that any
transmission resulting from the application of test is correctly interpreted.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 18/45

Chapter 4

Electrostatic Discharges Immunity Test

ESD Test information:
Test setup: Shielded room, According to EN 61000-4-2
Test setup for table-top equipment at laboratory tests:
Typical position for
indirect discharge to VCP

Typical position for
indirect discharge

Typical position for
indirect discharge to HCP

VPC
0.5m X 0.5m

Insulation

Horizontal coupling place
1.6m X 0.8m

Power Supply

0.1 m

Wooden table H=0.8m
470kohm
Resistor

Ground Reference Plane

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 19/45

Test levels: (Apply Level 2 and Level 3)
1a — Contact discharge
Level
Test voltage

1b — Air discharge
Level
Test voltage

(kV)

(kV)

1

2

1

2

2
3

4
6

2
3

4
8

4

8

4

15

X

Special

X

Special

NOTE: “X” is an open level. The level has to be specified in the dedicated equipment specification. If
higher voltages than those shown are specified, special test equipment may be needed.

Test Voltage:
( X ) 4KV contact discharge ( X ) 8KV air discharge
Indirect Discharges: ( X ) HCP
( X ) VCP
Polarity:
( X ) Positive
( X ) Negative
Test mode: Refer to Test method of Chapter 1
Test points: Chassis of EUT.
Test instruments:
Name
Best Plus BURST ESD
SURGE TRANSIENTS
BEST EMC Test
Instrument

Model Number
Best Plus V6.2

Serial Number
199749-019SC

Selected

BEST EMC V2.3
(-8, -9)

199918-006SC

KeyTek Instrument
ESD Test system

Series 2000

9204303/9204310
9209226/9301395

NoiseKen Electrostatic
Discharge Simulator
NoiseKen Electrostatic
Discharge Gun

ESS-100L(A)

2100C03605

TC-815P

2100C03566

X

Comment:
Performance Criteria: (According to ETSI EN 301 489-1)
( X ) Enclosure

(

)CT

( X )TT

( ) CR

( X )TR

( ) Signal and control ports

( )CT

( )TT

( ) CR

( )TR

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 20/45

EN 61000-4-2 PHOTO OF TEST SET-UP

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 21/45

Chapter 5

Radio Frequency Immunity Test (RS)

RS Test information:
Test setup: GTEM cell
Radiated Immunity Test Setup

Model 7122
Isotropic Probe

High Power
Amplifier

GTEMI Cell

EUT

Signal
Generator
EUT Performance
Monitor
Model 7122 Co mpanion
Metering Unit

Modulation
Generator
Model 7110 Data
Processing / Interface Unit

Test levels: (Apply Level 2)
Level

Test Field Strength
(V/m)

1

1

2
3

3
10

X

Special

NOTE: the “X” is an open test level. This level may be given in the product specification.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 22/45

Field strength:

( X ) 3V/m at 80 ~ 1000 MHz

Modulation:

( X ) 3V/m at 1400 ~ 2000 MHz
( ) FM %
( X ) 80% AM Modulation with 1KHz
(
(

( X ) 1% step size
( X ) 2.5 Second

Step size:
Sweep time:
Test mode:

) 80% AM Modulation with 400Hz when signal is modulated at 1kHz
) 900 KHz²5 KHz with PM 200 Hz and 100% depth

Ref. Test method of Chapter 1

Test instruments:
Name
EMCO GTEM

Model Number
5317

Serial Number
9411-1123

Selected
X

EMCO Probe

7122

9406-1194

X

EMCO METERING UNIT

7122

9406-1194

X

EMCO data interface
HP Personal Computer

7110
D3178A

9410-1273
3438S00486

X
X

HP Signal Generator

8657B

2928U00286

X

HP Signal Generator
IFI Wideband Amplifier

83711A
SMX50

3429A00434
467-0795

X
X

Min-circuit Amplifier

GFL-2500VH

N/A

X

WG radiation meters
WG E- filed

EMC-20
2244 / 90.20

BN2244129
Z-0001

X
X

HP Transmission Test Set

4935A

3115A24046

X

B & K Precision Sound Level Meter

Type 2232

1810564

X

Comment:
Performance Criteria: (According to ETSI EN 301 489-1)
( X ) Enclosure

( X )CT

( )TT

( X ) CR

( )TR

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 23/45

EN 61000-4-3 PHOTO OF TEST SET-UP

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 24/45

Chapter 6

Electric Fast Transient/Burst Requirements Test

EFT Test information:
General test set-up for laboratory type tests:

> 0.25 m
> 0.25 m
> 0.25 m
> 0.25 m

EUT

(L)

(L)
EUT

AC mains
supply

Capacitive
coupling clamp
AC mains
supply

EUT
EUT

0.1 m
0.1 m

Insulating
support

Reference
plane

EFT/Bgenerator (B)

Grounding connection
according to the
manufacturer’ s
specification.
Length to be specified
in the test plan.

Non-metallic
table
EFT/Bgenerator

(L) = length between clamp and EUT to be tested, should
not be more than 1-meter
(A) = location for supply line coupling
(B) = location for signal lines coupling

Coupling / decoupling
network (A)

Reference
plane

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 25/45

Test levels: (Apply Level 2)
Open-circuit output test voltage (±10%) and repetition rate of the impulses (±20%)
On power supply port, PE
On input/output signal, data and
Level

control ports
Voltage peak

Repetition rate

Voltage peak

Repetition rate

kV

kHz

kV

kHz

1
2

0.5
1

5
5

0.25
0.5

5
5

3

2

5

1

5

4
X

4
Special

2.5
Special

2
Special

5
Special

NOTE: the “X” is an open level. The level has to be specified in the dedicated equipment specification

Test setup: According to EN 61000-4-4
Test Voltage:
DC Power line
( ) 0.5 KV, 5 KH
AC Power line
( X ) 1 KV, 5 KHz
Signal & Control line ( ) 0.5 KV, 5 KHz; ( ) 1 KV, 5 KHz
Polarity:
( X ) Positive
( X ) Negative
Test Duration: ( X ) 1 minute
( ) 3 minutes
Connected lines: ( ) Power line shielded
( X ) Power line non-shielded
( ) Signal & Control line non-shielded
( ) Signal & Control line shielded
Test mode: Ref. Test method of Chapter 1.
Test instrument:
Name
Model Number
Best Plus BURST ESD Best Plus V6.2
SURGE TRANSIENTS

Serial Number
199749-019SC

Selected

BEST EMC Test
Instrument

BEST EMC V2.3
(-8, -9)

199918-006SC

KeyTek Instrument
EFT Test system

E412

9505206/505207

X

Comment:
Performance Criteria: (According to ETSI EN 301 489-1)
( ) Signal and control ports

( )CT

( )TT

( ) CR

( )TR

( ) DC power input ports

( )CT

( )TT

( ) CR

( )TR

( X ) AC mains input ports

(

( X )TT

( ) CR

( X )TR

)CT

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 26/45

EN 61000-4-4 PHOTO OF TEST SET-UP

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 27/45

Chapter 7

Surge Immunity Test

Surge Test information:
Test setup:

According to EN 61000-4-5

Test levels: (Apply Level 2 and Level 3)
Level

Test Field Strength
(kV)

1

0.5

2
3

1.0
2.0

4

4.0

X
Special
NOTE: the “X” is an open class. This level may be specified in the product specification.
Test Voltage:

DC Power line ( ) 0.5 KV
AC Power line ( ) Line – Line: 1KV
( ) Line – Ground: 2KV
( X ) Line – Line: 0.5KV
( X ) Line – Ground: 1KV
Control line
( ) 0.5 KV
Signal
( ) 1 KV, ( ) 0.5KV

Time:

( X ) 1.2/50µs [8/20µs]

Polarity:

( X ) Positive

( X ) Negative

Connected lines: ( ) Power line shielded
( X ) Power line non-shielded
( ) Signal & Control line non-shielded
( ) Signal & Control line shielded
Test mode: Ref. Test method of Chapter 1.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 28/45

Test instrument:
Name
Model Number
Best Plus BURST ESD Best Plus V6.2

Serial Number
199749-019SC

SURGE TRANSIENTS
BEST EMC Test
BEST EMC V2.3

199918-006SC

Instrument

(-8, -9)

KeyTek Pulsed-EMI

E103, 501B, E502B,

0008260 ~0008264,

Test System

E503, E505A,
E4552A

0008254

Selected

X

Comment:
Performance Criteria: (According to ETSI EN 301 489-1)
( X ) AC mains input ports
(

) Signal and control ports

( )CT
( )CT

( X )TT
( )TT

( ) CR
( ) CR

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

( X )TR
( )TR

Test Report ------------------------------------------------------------------------------- 29/45

EN 61000-4-5 PHOTO OF TEST SET-UP

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 30/45

Chapter 8

Continuous Wave Voltage Immunity Test

CS Test information:
Test setup: According to EN 61000-4-6
Immunity test to RF conducted disturbances:

CDN: Coupling and
decoupling network

Auxiliary
equipment 1

CDN

Equipment
under test

Auxiliary
equipment 1

CDN

0.1 m
support

Ground reference plane
T

T2: Power attenuator
(6dB)

T: Termination 50ohm

T2
RF — generator
Test generator
Test levels:

(Apply Level 2)
Frequency range 150kHz to 80MHz
Level

Voltage level (e.m.f.)

1

Uo [dB(µv)]
120

Uo [V]
1

2

130

3

3
X

140

10
Special

NOTE: the “X” is an open test level.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 31/45

Test Frequency:

( X ) 0.15 ~ 80MHz

Modulation:

(

) FM

%

( X ) 80% AM Modulation with 1kHz

Step size:

(
(

) 80% AM Modulation with 400Hz when signal is modulated at 1kHz
) 900 MHz²5 MHz with PM 200 Hz and 50% duty cycle

(

) Performed over the frequency range 150kHz to 80MHz with the

exception of an exclusion band for transmitters, and for receivers and
duplex transceivers
( X ) For receivers and transmitters the stepped frequency increments shall
be 1% frequency increment of the momentary frequency in the
frequency range 150kHz to 80MHz, unless specified otherwise in the
part of EN 301 489 dealing with the particular type of radio equipment
Field strength:

(

) 1Vrms

( X ) 3Vrms

(

Connected lines:

( ) Power line shielded
( X ) Power line non-shielded
( ) Signal & Control line non-shielded
( ) Signal & Control line shielded

) 10Vrms

Test mode: Ref. Test method of Chapter 1

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 32/45

Test instruments:
Name
FRANKONIA EMV–Mess–
System
FRANKONIA CDN

Model Number
CIT-10

Serial Number
103A3113

Selected
X

M2+M3

A3011015

X

FRANKONIA CDN

T2-801

A3010002

FRANKONIA CDN
FRANKONIA CDN

T4-801
S1-801

A3015004
A3005002

SCHAFFNER FM-Koppelzange

KEMZ 801

17045

SCHAFFNER RF-SYNTHE
SIZERIAMP21FIER
SCHAFFNER CDN
SCHAFFNER CDN

NSG 2070-1

1020

M325
M216

13773
15604

SCHAFFNER CDN

T004

15230

SCHAFFNER CDN
SCHAFFNER FM-Koppelzange

S501
KEMZ 801

15167
14301

HP Transmission Test Set

4935A

3115A24046

B & K Precision Sound Level Meter Type 2232

1810564

Comment:
Performance Criteria: (According to ETSI EN 301 489-1)
( ) Antenna port

( )CT

( )TT

( ) CR

( )TR

( ) Signal and control ports

( )CT

( )TT

( ) CR

( )TR

( ) DC power input ports

( )CT

( )TT

( ) CR

( )TR

( X ) AC mains input ports

( X )CT

( )TT

( X ) CR

( )TR

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 33/45

EN 61000-4-6 PHOTO OF TEST SET-UP

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 34/45

Chapter 9

Voltage DIP / Interruption Test

DIP Test information:
Test setup: According to EN 61000-4-11
Voltage dips :

( X ) 30%, 0.01 Second
( X ) 60%, 0.1 Second

Voltage interruptions: ( X ) > 95%, 5 Seconds
Test mode: Ref. Test method of Chapter 1
Test instruments:
Name
Model Number
Best Plus BURST ESD Best Plus V6.2
SURGE TRANSIENTS

Serial Number
199749-019SC

BEST EMC Test
Instrument

BEST EMC V2.3
(-8, -9)

199918-006SC

Partner EMS Tester

Transienter-1000

PIO

Selected

X

Comment:
Performance Criteria: (According to ETSI EN 301 489-1)
Dips 30%:
( X ) CT
( ) TT
( X ) CR
Dips 60%:
( ) CT
( ) TT
( ) CR
Interruptions >95%: ( ) CT
( ) TT
( ) CR
No unintentional responses shall occur at the end of the test;
( )Event of loss of function(s)
( )Event of loss of user stored data

Performance Criteria: (According to ETSI EN 301 489-17)
Dips 60%, 100 ms :
( ) A
( ) B
Interruptions >95%, 5 000 ms:
( ) A
( ) B

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

( ) TR
( ) TR
( ) TR

(X)C
(X)C

Test Report ------------------------------------------------------------------------------- 35/45

EN 61000-4-11 PHOTO OF TEST SET-UP

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 36/45

Chapter 10

Harmonics Test

Test information:
Test setup:

According to EN 61000-3-2

Test item:
Test mode:

Quasi – stationary & Fluctuating Current Harmonics Test.
Ref. Test method of Chapter 1

Test instrument:
Name
Model Number
Harmonic/Flicker Test HP 6842A
System

Test Equipment Settings:

Serial Number
3531A-00102

Selected
X

Line Voltage

Quasi-stationary Current
Harmonics Test
230VAC

Fluctuating Current
Harmonics Test
230VAC

Line Frequency
Device Class

50Hz
D

50Hz
D

Test Limit Overrides

None

None

Total Number of Failures:

None

None

Total Number of Errors:

None

None

Test Result: Pass

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 37/45

Chapter 11 Voltage Fluctuation and Flicker Test
Test information:
Test setup:

According to EN 61000-3-3

Test mode:

Ref. Test method of Chapter 1

Test instrument:
Name
Model Number
Harmonic/Flicker Test HP 6842A
System

Serial Number
3531A-00102

Selected
X

Test Equipment Settings:
Line Voltage
Line Frequency

230VAC
50Hz

Test Limit Overrides

None

Total Number of Failures:

Pst: (0), Plt: (0)
Dc: (0), Dmax (0), Dt (0)

Total Number of Errors:

None

Test Result: Pass

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 38/45

Chapter 12 Conducted Emission Test
Test condition and setup
All the equipment is placed and setup according to EN 55022.
Mains power:
The EUT is assembled on a wooden table, which is 80 cm high and placed 40 cm from the
back-wall, which is a vertical conducting plane. One LISN is for EUT, the other LISN is for
support equipment. They are all placed on the conductive ground. The EUT’ s LISN connect a
line switch box for selecting L1 or L2, then connect to a preamplifier and spectrum.
The spectrum scans from 150KHz to 30MHz. Conducted emission levels are detected at
maximum peak mode. But if the maximum peak mode failed or over average limit, it will be
measured by average detection mode.
While testing the worst-emission plot printed in the peak detection mode, and there are up
to 6 highest emissions to be recorded. The plot is kept as the original data and not included in the
test report.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 39/45

List of test Instrument
Calibration Date

Instrument Name

Model

Brand

Serial No.

Next time

EMI Receiver

8546A

HP

3520A00242

08/05/05

RF Filter Section

85460A

HP

3448A00217

08/05/05

LISN

LISN-01

TRC

99-05

10/07/05

LISN-01

TRC

9912-03, 04

11/04/05

15542 ZFL-500

Mini –

0 0117

05/20/05

Mini –

9915 –

05/20/05

Circuits

Conducted

Mini –

0215 –

Circuits

Conducted

A30A30-0058-50FS-2M

Jyebao

SMA-08

05/20/05

A30A30-0058-50FS-1M

Jyebao

SMA-09

05/20/05

RG-214/U

Jyebao

NP-01

05/20/05

RG-214/U

Jyebao

NP-02

05/20/05

ASB-01

TRC

9904-01

05/20/05

(EUT)
LISN
(Support E.)
Pre-amplifier

Circuits
6dB

MCL BW-S6W2

Attenuator
10dB

A5542 VAT010

Attenuator
Coaxial Cable

05/20/05

(2 meter)
Coaxial Cable
(1.1 meter)
Coaxial Cable
(20 meter)
Coaxial Cable
(20 meter)
Auto Switch Box
(< 30MHz)
The level of confidence of 95%, the uncertainty of measurement of conducted emission is +2.43dB / -2.53dB.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 40/45

Conducted Test Placement (Front view and Side view)

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 41/45

Test Result of Conducted Emissions for Mains power
Test Conditions: Temperature : 25 °C Humidity : 73 % RH
Power

Connected

Conductor Frequency
(KHz)

Line 1

Line 2

Emissions

Class

B

Peak

QP

Average

QP-limit

AVG-limit

Margin

(dBµ V)

(dBµ V)

(dBµ V)

(dBµ V)

(dBµ V)

(dB)

197.000

32.95

---

---

64.66

54.66

-21.71

331.000

29.21

---

---

60.83

50.83

-21.62

528.000

29.79

---

---

56.00

46.00

-16.21

788.000

28.02

---

---

56.00

46.00

-17.98

4406.000

32.88

---

---

56.00

46.00

-13.12

5940.000

29.86

---

---

60.00

50.00

-20.14

6000.000

29.09

---

---

60.00

50.00

-20.91

6140.000

29.49

---

---

60.00

50.00

-20.51

262.000

30.37

---

---

62.80

52.80

-22.43

329.000

33.12

---

---

60.89

50.89

-17.77

533.000

33.19

---

---

56.00

46.00

-12.81

788.000

31.05

---

---

56.00

46.00

-14.95

4406.000

32.37

---

---

56.00

46.00

-13.63

4762.000

30.47

---

---

56.00

46.00

-15.53

6460.000

30.91

---

---

60.00

50.00

-19.09

6670.000

30.53

---

---

60.00

50.00

-19.47

Note:
1. The reading amplitudes are all under limit.
2. Testing result = Amplitude reading + Correction factor (Insertion loss of LISN, Cable loss,
Attenuator, Amplifier and so on)

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 42/45

Chapter 13 Radiated Emission Test
Test condition and setup
Pretest:

Prior to the final test (OATS test), the EUT is placed in a shielded enclosure,

and scan from 30MHz to 1GHz. This is done to ensure the radiation is exactly emitted from the
EUT.

Final test:

Final radiation measurements are made on a 10 – meter, open-field test

site. The EUT is placed on a nonconductive table, which is 0.8m height, the top surface is 1.0 x
1.5 meter. The entire placement is according to EN 55022.
The whole range antenna is used to measure frequency from 30 MHz to 1GHz. The final
test is used the spectrum analyzer (EMI Receiver). Measure more than six top marked
frequencies generated form pretest by computer step by step at each frequency.
The EUT is rotated 360 degrees, and antenna is raised and lowered from 1 to 4 meters to
find the maximum emission levels. The antenna is used with both horizontal and vertical
polarization.
Appropriated preamplifier which is made by TRC is used for improving sensitivity and
precautions is taken to avoid overloading .The spectrum analyzer’ s 6dB bandwidth is set to 120
kHz, and the EUT is measured at quasi-peak (below 1GHz) mode.
If the emission is close to the frequency band of ambient, the tester will recheck the data
and the corrected data will be written in the test data sheet. If the emission is just within the
ambient, the data from shielded room will be taken as the final data.

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 43/45

List of test Instrument
Calibration Date

Instrument Name

Model

Brand

Serial No.

Next time

EMI Receiver

8546A

HP

3520A00242

08/05/05

RF Filter Section

85460A

HP

3448A00217

08/05/05

Small Biconical

UBAA9114 &

SCHWARZECK

127

10/11/05

Antenna

BBVU9135

Pre-amplifier

PA1F

TRC

1FAC

05/20/05

Auto Switch Box

ASB-01

TRC

9904-01

05/20/05

A30A30-0058-50FS-15M

JYEBAO

SMA-08

05/20/05

A30A30-0058-50FS-1M

JYEBAO

SMA-02

05/20/05

Receiver

SCR3102

SCHAFFNER

012

05/13/05

Control Box

TWR95-4

TRC

C9001-2

N/A

Antenna

CBL6141A

SCHAFFNER

4206

05/26/05

Pre-amplifier

TRC-CB-2

TRC

CB-002

05/28/05

Coaxial cable

RG-214/U

JYEBAO

Cl-002

05/28/05

BNC31VB-0316

JYEBAO

SMA-02

05/28/05

BNC31VB-0318

JYEBAO

SMA-02

05/28/05

BNC31VB-0316

JYEBAO

SMA-02

05/28/05

BNC31VB-0316

JYEBAO

SMA-02

05/28/05

(>30MHz)
Coaxial Cable
(Double shielded,
15 meter)
Coaxial Cable
(1.1 meter)

(20 meter)
Coaxial Cable
(50 cm)
Coaxial Cable
(1.1 meter)
Coaxial Cable
(1.1 meter)
Coaxial Cable
(1.1 meter)
The level of confidence of 95% , the uncertainty of measurement of radiated emission is +2.85dB / -2.77dB .

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 44/45

Radiated Test Placement (Front view and Rear view)

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Test Report ------------------------------------------------------------------------------- 45/45

Test Result of Spurious Radiated Emissions
Test Conditions:
Testing room :

Temperature : 25 ° C

Humidity : 73 % RH

Testing site :

Temperature : 22 ° C

Humidity : 65 % RH

Test Result of Spurious Radiated Emissions for 30MHz to 1GHz [Horizontal]
Frequency

MHz

Reading

Ant.

Amplitude

Height

dBµV

m

Table

degree

Correction

Corrected

Class B

Factors

Amplitude

Limit

dB/m

dBµV/m

dBµV/m

Margin

dB

75.7728

31.57

2.29

270

-10.17

21.40

30.00

-8.60

355.8113

16.48

1.00

156

2.04

18.52

37.00

-18.48

552.0938

12.11

1.88

47

8.17

20.28

37.00

-16.72

753.7826

11.47

1.00

156

14.28

25.75

37.00

-11.25

Test Result of Spurious Radiated Emissions for 30MHz to 1GHz [Vertical]
Frequency

MHz

Reading

Ant.

Amplitude

Height

dBµV

m

Table

degree

Correction

Corrected

Class B

Factors

Amplitude

Limit

dB/m

dBµV/m

dBµV/m

Margin

dB

39.4230

24.17

2.48

308

-0.47

23.70

30.00

-6.30

54.9095

22.98

1.00

43

-6.52

16.46

30.00

-13.54

76.9673

32.50

1.00

30

-10.12

22.38

30.00

-7.62

169.3797

27.12

1.00

359

-5.88

21.24

30.00

-8.76

338.7602

20.98

1.00

9

0.98

21.96

37.00

-15.04

432.0596

17.70

2.47

63

5.24

22.94

37.00

-14.06

Note:

1. Margin = Amplitude – limit, if margin is minus means under limit.
2. Corrected Amplitude = Reading Amplitude + Correction Factors
3. Correction factor = Antenna factor + (Cable Loss – Amplitude gain) + Switching Box Loss

Report No.: C51ET050304 (ETSI EN 301 489)
Training Research Co., Ltd., TEL: 886-2-26935155, Fax: 886-2-26934440

Copy of the R&TTE Declaration of
Conformity (DoC)

Declaration of Conformity
We, the under signed,
Company
Address, City
Country
Phone number
Fax number
E-mail

CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6, Taipei 114,
Taiwan
886-2-27908998
886-2-27909463
Jason_Chang@mail.cameo.com.tw

certify and declare under our sole responsibility that the following equipment:
Product Description / Supplementary Info
Manufacturer
Brand
Type

802.11g Wireless PCI Adapter
CAMEO COMMUNICATIONS, INC.
CAMEO, Level One, LG, Etherwan, Allnet GmbH
WLG-1202, WNC-0300, LWS5410P, NWP-0108G, ALL0281A

is tested to and conforms with the essential radio test suites included in the following standards:
Standard
ETSI EN 300 328-2
ETSI EN 301 489-1
ETSI EN 301 489-17
EN 60950-1

Issue date
V1.2.1 Dec. 2001
V1.4.1 Aug. 2002
V1.2.1 Apr. 2002
2001

and therefore complies with the essential requirements and provisions of the R&TTE directive
1999/5/EC of the European Parliament and of the council of 9March 1999 on radio equipment and
Telecommunications Terminal Equipment and the mutual recognition of their conformity and the
requirements of Annex IV (conformity Assessment procedure referred to in article 10(4)).
The following Notified Bodies have been consulted in the Conformity Assessment procedure:
Notified Body number
0470

Name and address
Nemko, PO Box 73, Blindern N-0314 Oslo, Norway

The technical documentation as required by the Conformity Assessment procedure is kept at the
following address:
Company
Address, City
Country
Phone number
Fax number
E-mail

CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6, Taipei 114,
Taiwan
886-2-27908998
886-2-27909463
Jason_Chang@mail.cameo.com.tw

Draw up in
Date

TAIWAN, R.O.C.
2005/4/27
CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6,
Taipei 114, Taiwan

Signature & company stamp

Jason Chang /
Wireless Comm. R&D Dept. Manager

Product Quality
Assurance Documents

Declaration of Product Quality Assurance
In accordance with the Conformity Assessment procedure referred to in article 10(3) of R&TTE
Directive 1999/5/EC of the European Parliament and the council of 9 march 1999 on the Radio
equipment and Telecommunication Terminal Equipment and their mutual recognition of their conformity
(R&TTE directive) the following manufacture:
Company
Address, City
Country
Phone number
Fax number
E-mail

CAMEO COMMUNICATIONS, INC.
6F, NO. 22, Chung Shin Rd., Hsi-Chih,
Taipei 221, Taiwan
886-2-26499800
886-2-26499984
Jason_Chang@mail.cameo.com.tw

declares under its sole responsibility that it had taken the following measures in order to achieve that
the manufacturing process ensures compliance of the manufactured products with the technical
documentation as established by CAMEO COMMUNICATIONS, INC.. under the requirements of the
R&TTE directive and with the requirements of R&TTE directive that apply to them:
Number
01

Measures taken in order to achieve that the manufacturing process ensures
compliance of the manufactured products
Manufacturing of the equipment is subcontracted by CAMEO
COMMUNICATIONS, INC. to CAMEO COMMUNICATIONS, INC. located at 6F,
NO. 22, Chung Shin Rd., Hsi-Chih, Taipei 221, Taiwan. who is ISO 9001 certified
for development, production and distribution of radio products. (See copy of ISO
9001 certification attached)

Draw up in
Date

TAIWAN, R.O.C.
2005/4/27
CAMEO COMMUNICATIONS, INC.
No. 42, Min Chuan East Road, Section 6,
Taipei 114, Taiwan

Signature & company stamp

Jason Chang /
Wireless Comm. R&D Dept. Manager



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2005:04:29 02:01:32Z
Modify Date                     : 2005:05:03 18:53:20+08:00
Page Count                      : 146
Creation Date                   : 2005:04:29 02:01:32Z
Mod Date                        : 2005:05:03 18:53:20+08:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : Weng1
Metadata Date                   : 2005:05:03 18:53:20+08:00
Creator                         : Weng1
Title                           : Microsoft Word - RTTE-TCF Form.doc
Has XFA                         : No

EXIF Metadata provided by EXIF.tools