509060 Manual

2009-10-12

: Pdf 509060 Manual 509060_manual 510 s

Open the PDF directly: View PDF .
Page Count: 76

1-Port

USB

WireleSS

Server

USer

manUal

MODEL 509060

INT-509060-UM-0508-01

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™ 1-Port USB Wireless Print

Server, Model 509060. Designed to work with any access point or peer-to-peer wireless network,

this server connects any USB printer to your network and is compatible with all major operating

systems. Its 10/100 Mbps Ethernet network port connection lets you operate wired or wireless,

and its pocket size makes it an easy t in portable tool kits.

The easy-to-follow instructions in this user manual help make setup and operation relatively

simple. NOTE: Some screen images have been modied to t the format of this manual.

Safety & comPliance StatementS

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC (Federal Communication Commission) Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

This equipment must be installed and operated in accordance with provided instructions, and a

minimum of 20 cm spacing must be provided between the computer-mounted antenna and a

person’s body (excluding hands and feet) during wireless modes of operation. As this device

complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: 1)

This device may not cause harmful interference; and 2) this device must accept any interference

received, including interference that may cause undesired operation. Any changes or modications

not expressly approved by the party responsible for compliance could void the authority to operate

equipment.

FCC Radiation ExposuRE statEmEnt

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. To avoid the possibility of exceeding these limits, human proximity to the antenna

shall not be less than 20 cm (8 inches) during normal operation. The antenna(s) used for this

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

R&ttE ComplianCE statEmEnt

This equipment complies with all the requirements of Directive 1999/5/EC of the European

Parliament and the Council of March 9, 1999, on radio equipment and telecommunication terminal

equipment (R&TTE) and the mutual recognition of their conformity. The R&TTE directive repeals

and replaces Directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth

Station Equipment) as of April 8, 2000.

Eu CountRiEs intEndEd FoR usE

The ETSI version of this device is intended for home/ofce use in Austria, Belgium, Denmark,

Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal,

Spain, Sweden and the U.K., and is also authorized for use in EFTA member states Iceland,

Liechtenstein, Norway and Switzerland. (EU countries not intended for use: none.)

SAFETY & COMPLIANCE

contentS

1. INTRODUCTION....... ........................................................................................................... 6

1.1 Network Printing Architecture ..................................................................................... 6

1.1.1 Print Server Network Functions ...................................................................... 6

1.1.2 Network Printing Functions for Clients ........................................................... 6

1.1.3 Network Printing Functions for a Network Server .......................................... 7

1.2 Network Printing Environment ....................................................................................8

2. HARDWARE INSTALLATION ............................................................................................. 9

3. WINDOWS PEER-TO-PEER NETWORK ........................................................................... 9

3.1 System Architecture .................................................................................................... 9

3.2 Administrator Installation and Setup ......................................................................... 10

3.3 Administrator Utilities ................................................................................................ 13

3.4 Client Installation and Setup ..................................................................................... 14

3.5 Client Utilities... ......................................................................................................... 16

3.5.1 Network Ports Quick Setup ......................................................................... 17

3.5.2 Remote Ports Utility..................................................................................... 17

3.6 Windows Add Printer Procedure .............................................................................. 19

3.6.1 Windows Vista ................................................................................................. 19

3.6.2 Windows XP ....................................................................................................22

4. WINDOWS NT/2000/SERVER 2003 NETWORK .............................................................24

4.1 System Architecture .................................................................................................. 24

4.2 Windows NT/2000/Server 2003 Server Installation and Setup ................................ 24

4.3 User Installation ........................................................................................................ 25

5. NETWARE NETWORK ..................................................................................................... 26

5.1 System Architecture ................................................................................................. 26

5.2 NetWare 3.x/4.x/5.x Installation & Setup .................................................................. 26

5.2.1 Installation Using PCONSOLE .................................................................... 26

6. UNIX SYSTEM NETWORK ............................................................................................... 28

6.1 Introduction...... ......................................................................................................... 28

6.2 Enable Print Server’s TCP/IP Support...................................................................... 28

6.3 Set Up the Print Server’s IP Address ....................................................................... 28

6.3.1 DHCP .......................................................................................................... 28

6.3.2 BOOTP ........................................................................................................ 28

6.4 Verify the Print Server’s IP Address ......................................................................... 29

6.5 Congure Remote LPD Printing on the Host ............................................................ 29

7. CONFIGURATION UTILITY .............................................................................................. 30

7.1 Introduction........ ....................................................................................................... 30

7.2 Search for All Available Print Servers ....................................................................... 31

7.3 Status of the Print Server .......................................................................................... 32

7.4 Set Up the Print Server ............................................................................................. 33

7.5 General Conguration ............................................................................................... 34

7.6 TCP/IP Conguration ................................................................................................34

7.7 NetWare Print Server Conguration ......................................................................... 35

7.8 AppleTalk Conguration ............................................................................................35

7.9 Bonjour Conguration ............................................................................................... 36

7.10 SNMP Conguration .................................................................................................36

7.11 SMB Conguration ................................................................................................... 36

7.12 System Conguration ............................................................................................... 37

7.13 Wireless Conguration ............................................................................................. 38

CONTENTS

7.14 Wizard......................................................................................................................... 43

7.15 Report................ ......................................................................................................... 46

8. WEB MANAGEMENT ........................................................................................................46

8.1 Introduction.................... ............................................................................................. 46

8.2 Login................. ......................................................................................................... 46

8.3 Device Status.... ........................................................................................................ 47

8.3.1 System ......................................................................................................... 47

8.3.2 Printer .......................................................................................................... 47

8.3.3 TCP/IP ......................................................................................................... 48

8.3.4 SMB.... ......................................................................................................... 48

8.3.5 SNMP ..........................................................................................................49

8.3.6 NetWare ...................................................................................................... 49

8.3.7 AppleTalk .....................................................................................................50

8.3.8 Bonjour ........................................................................................................ 50

8.4 Setup Wizard... ......................................................................................................... 51

8.4.1 System ......................................................................................................... 51

8.4.1.1 Admin Password ............................................................................ 51

8.4.1.2 Advanced Settings ........................................................................ 52

8.4.2 Wireless ....................................................................................................... 52

8.4.2.1 Site Survey .................................................................................... 53

8.4.2.2 Encryption .....................................................................................54

8.4.3 TCP/IP .........................................................................................................56

8.4.4 SMB... .......................................................................................................... 57

8.4.5 SNMP ..........................................................................................................58

8.4.6 NetWare.......................................................................................................58

8.4.7 AppleTalk ..................................................................................................... 59

8.4.8 Bonjour ........................................................................................................60

8.4.9 Save Settings ..............................................................................................60

8.5 System Tools... ......................................................................................................... 61

8.5.1 Load Default ................................................................................................. 61

8.5.2 Upgrade Firmware from Browser ................................................................. 61

8.5.3 Backup Setting ............................................................................................. 62

8.5.4 Restore System ...........................................................................................62

8.5.5 Language .....................................................................................................63

9. TELNET MANAGEMENT ................................................................................................... 63

9.1 Introduction........ .......................................................................................................... 63

9.2 Login ..... ............ .......................................................................................................... 63

9.3 Get Setting Values – The ‘get’ Command .................................................................. 64

9.4 Modify Setting Values – The ‘set’ Command..............................................................66

9.5 Other Commands ....................................................................................................... 67

10. IPP PRINTING......... ......................................................................................................... 68

10.1 Introduction...... .......................................................................................................... 68

10.2 System Setup............................................................................................................ 68

10.2.1 Print Server Side .......................................................................................... 68

10.2.2 Client Side ....................................................................................................68

11. WINDOWS XP SP2 SETUP .........................................................................................................70

12. SPECIFICATIONS ....................................................................................................................... 74

CONTENTS

1. introdUction

1.1 Network Printing Architecture

By rst introducing the roles of a print server, client user and network server in the

network-printing environment, this section illustrates how the 1-Port USB Wireless

Print Server — often referred to subsequently simply as “the print server” —

functions and operates on the network. Before you install and use the print server,

it is strongly recommended that you read this section completely, then select only

the chapters you

need according to

your network

operating system.

The print server

provides a complete

network printing

solution, including

peer-to-peer printing

(PTPP), TCP/IP

(LPR), IPP printing,

NetWare bindery

printing, AppleTalk

and SMB printing.

1.1.1 Print Server Network Functions

Because the 1-Port USB Wireless Print Server

supports IPX/SPX, NetBEUI, TCP/IP and AppleTalk

network protocols, any networked computer can

directly print to it through any of its installed

protocols.

1.1.2 Network Printing Functions for Clients

The 1-Port USB Wireless Print Server provides a

PTPP (peer-to-peer printing) driver and utilities for

Windows 95/98SE/Me/NT/2000/XP/Server 2003/

Vista users. PTPP supports the TCP/IP protocol.

Windows NT Server

NetWare Server

Windows 98Windows NT

Workstation

Windows 2000

Unix Print Server

Network Printing Environment

Print Server

Client User

Network Server

Windows NT Server

NetWare Server

Windows 98

Windows NT

Workstation

Windows 2000

Unix Print Server

Print Server

Windows NT Server

NetWare Server

Windows 98Windows NT

Workstation

Windows 2000

Unix Print Server

Client User

INTRODUCTION

In the client installation procedure, after the PTPP driver is installed in Windows,

the system will automatically (manual conguration is also allowed) search all the

print servers on the network and then add their printing ports into Windows’ printing

port (see below).

UNIX (including HP/UX, SCO Unix, SunOS, Solaris, Unixware DECUnix, IBM AIX

and others) and Linux use the system-standard LPR to print through the print server.

MAC OS can use the system-standard AppleTalk network to print through the print

server.

1.1.3 Network Printing Functions for a Network Server

The 1-Port USB Wireless Print Server provides a

PTPP driver and utilities for Windows NT/2000/

Server 2003/Vista. After PTPP is installed, the

server can directly print through the print server.

Adding this printing function to Windows allows many advanced features to be used,

such as print queue and user authority management.

In a NetWare environment, the 1-Port USB Wireless Print Server offers various

printing modes, such as print queue, remote printer, etc.

Windows 98

PTPP

Print Server

MIS-2

P1 P2

Print Server

MIS-1

Windows NT Server

NetWare Server

Windows 98Windows NT

Workstation

Windows 2000

Unix Print Server

Network Server

INTRODUCTION

1.2 Network Printing Environment

In a Windows peer-to-peer network, the client’s PTPP driver will use the TCP/IP

protocol to print through the print server.

In a Windows NT/2000/Server 2003/Vista network, the network printing function

will become available after the PTPP driver is installed in Windows. As stated

earlier, adding this printing function

allows many advanced features to

be used, such as print queue and

user authority management.

In a NetWare network, the 1-Port USB Wireless Print Server offers various printing

modes, such as print queue, remote

printer, etc.

INTRODUCTION

2. hardWare inStallation

1. Unpack the 1-Port USB Wireless Print Server package and verify that all the

items listed in the Package Contents section of the Specications are provided.

2. Connect the print server to the printer you want to share on the network.

3. Connect the print server to your network by attaching the network cable to the

UTP port of the print server.

4. Connect the power adapter to the print server. The print server will perform the

Power-On-Self-Test (POST) after it is turned on. During the POST, the Status

LED will be on. When the LEDs are unlighted, the print server is ready.

NOTE 1: Only use the power adapter shipped with the print server. Do NOT use

any other power adapter from any other sources.

NOTE 2: To avoid a compatibility problem between the 1-Port USB Wireless Print

Server and some printers, it is recommended that you turn on power to the 1-Port

USB Wireless Print Server before turning on the printer

3. WindoWS Peer-to-Peer netWork

3.1 System Architecture

The print server supports Windows’ Peer-to-Peer Network Printing mode, which is

suitable for most medium and small network environments.

The installation procedure is separated into two parts:

1. Administrator Installation and Setup (refer to section 3.2 for more detailed info).

System administrators must:

• Install the administrator’s utilities into his/her computer.

• Congure the print server from the administrator’s conguration utility.

2. Client Installation and Conguration (refer to section 3.3 for more detailed info).

Client users must:

• Install a Windows PTPP driver for network printing.

In addition, after PTPP is installed, the system will automatically search for all

print servers on the network and add the printing port of the print servers into

Windows’ printing port (refer to Network Printing Architecture in section 1.1 for

more detailed information).

HARDWARE INSTALLATION / WINDOWS PEER-TO-PEER NETWORK

3.2 Administrator Installation and Setup

The Administrator Installation can be performed on Windows 98SE/Me/NT/2000/

XP/Server 2003/Vista with the same user interface. Before the installation, verify

that your network protocol is installed on your PC (TCP/IP, IPX and/or NetBEUI). It

will be helpful in your installation process.

Insert the CD included with

the print server into your

CD-ROM drive. The

Autorun.exe program should

be executed automatically.

If not, run Autorun.exe

manually from the CD-ROM

drive’s root directory. The

Installation Manager will be

displayed on the screen

(shown at right). Click

“Administrator Installation.”

The “Utilities Setup” window

will be displayed. Click

“Next.”

Click “Next” to install the

utilities in the default folder,

or click “Browse” to specify

the destination folder where

you would like to install the

utilities.

WINDOWS PEER-TO-PEER NETWORK

Select the components you

want to install. It is highly

recommended that you

install all of the provided

components. Click “Next” to

continue.

Specify the program folder

where the program icons

will be added. Click “Next.”

The system will start to

install the utilities

automatically.

WINDOWS PEER-TO-PEER NETWORK

At this point, the installation

phase is complete. You can

prepare to congure the

print server. The “Choose

Print Server” eld will list all

print servers within the

network. Select the print

server you would like to

congure and click “Next.”

NOTE 1: If this is the rst

time you congure the print

server, the “Print Server

Name” is the last 6 digits of

the MAC ID with the prex

“PS.” Check the MAC ID on

the print server.

NOTE 2: The list can only display the devices from the same manufacturer.

Specify a recognizable

name for the print server

and click “Next.”

Specify the IP address for

the print server manually or

click “Next” to keep the

default IP address:

192.168.2.2.

WINDOWS PEER-TO-PEER NETWORK

The conguration summary

is displayed.Now, you have

completed the print server

setup. Click Finish” and

your system will add a

network port of the print

server to your PC

automatically.

At this point, the administrator

installation procedure is

done. Click “Finish.”

The Administrator Installation program performs the following tasks:

• Installs all utilities and drivers to the administrator’s PC.

•

Congures the print server (including the print server name and network protocol).

• Adds the network port of the print server to the administrator’s PC.

If you want to print from this administrator’s PC to the print server, all you need to

do is to perform Windows’ standard Add Printer procedure (refer to Section 3.6).

3.3 Administrator Utilities

After the Administrator Installation program is completed, there will be four utilities

in the print server’s Program folder.

Network Ports Quick Setup – Adds the network ports of print servers within the

network to your PC.

Print Server Conguration – Allows you to congure the print server’s IP address,

network protocols and other advanced functions. (Refer to Chapter 7 for detailed

instructions for the conguration.)

Remote Ports – Adds the network port of a remote printer server to your PC.

WINDOWS PEER-TO-PEER NETWORK

Uninstall – This “assistant”

serves to remove all

installed administrator

software.

3.4 Client Installation and Setup

The Client Installation program can be performed on Windows 98SE/Me/NT/2000/

XP/Server 2003/Vista with the same user interface. Before starting the installation

procedure, conrm that your PC has connected to the network and has installed at

least one network protocol.

Insert the included CD into

your CD-ROM drive. The

Autorun.exe program should

be executed automatically.

If not, run Autorun.exe

manually from the CD-ROM

drive’s root directory. The

Installation Manager will be

displayed on the screen

(shown at right). Click

“Client Installation.”

The “Utilities Setup” window

will be displayed. Click

“Next.”

WINDOWS PEER-TO-PEER NETWORK

Click “Next” to install the

utilities in the default folder,

or click “Browse” to specify

the destination folder where

you would like to install the

utilities.

Specify the program folder

where the program icons

will be added; click “Next.”

The system will start to

install the utilities

automatically.

WINDOWS PEER-TO-PEER NETWORK

Now that the installation

procedure is complete, you

are ready to set up the

client’s computer. All

network ports of the print

servers detected on the

network will be added to

your PC automatically. Click

“Continue.”

The Client Installation

procedure is complete.

Click “Finish.”

With this installation, the following tasks have been completed:

• Installation of all utilities and drivers to the client’s PC.

• Addition of all the print server’s network ports of the network to the client’s PC.

You can then perform Windows’ standard Add Printer procedure to add network

printers to your PC. (Refer to Section 3.6.)

3.5 Client Utilities

When Client Installation is

complete, there will be three

tools in the print server’s

Program folder: Network

Ports Quick Setup, Remote

Ports and Uninstall Network

Driver. Uninstall Network

Driver will assist you in

removing all installed client

software; the other two tools

are described below.

WINDOWS PEER-TO-PEER NETWORK

3.5.1 Network Ports Quick Setup

The Network Ports Quick Setup utility offers a very simple method to add or remove

the print server’s printer port from the client’s computer.

During the client’s installation procedure,

the system will automatically search for

all print servers on the network and add

them into the printer ports of the client’s

computer (shown at right).

If you have just installed another new print server in the network, you must run this

program rst. This program will search for new print servers and allow you to add

the new network printer port into the client’s computer conveniently. By performing

the standard Add Printer procedure, you can then print directly to the printer through

the newly installed print server.

Be aware that Network Ports Quick Setup utility can only detect and congure all

print servers on the same network: It cannot search and congure print servers on

other subnets across network segments. You must use the Remote Ports utility

described in the next section to manage remote (across network segments) print

servers.

3.5.2 Remote Ports Utility

The Remote Ports utility offers a convenient way fto manage and add a printer

port of the remote print server. From the assistant of this utility, you can print to

other print servers outside the subnet across a network segment. Note, however,

that this function only supports the TCP/IP network protocol.



WINDOWS PEER-TO-PEER NETWORK

1. Run the Remote Ports utility. Click “Add”

to add a remote printer port.

2. Enter the print server’s name and

IP address, select the ports used

and enter the LPR queue name

of each port. Click “OK.”

3. The new remote printer port is displayed.

In order to use the remote printing

function, you need to proceed with

the normal Add Printer procedure

and select your printer port as the

newly added remote printer port.

WINDOWS PEER-TO-PEER NETWORK

3.6 Windows Add Printer Procedure

After adding a network port of the print server to your PC using the Administrator

or Client Installation program, you can follow the procedure described below to

add a printer to Windows. NOTE: The following Add Printer steps are in Windows

Vista and XP: The steps in other operating systems are similar.

3.6.1 Windows Vista

1. Click “Start” and select “Settings\Printers.”

2. Click “Add a Printer.”

3. The Add Printer wizard is

displayed. Select “Add a

local printer.”

4. Choose the suitable printer

port created during the

installation process and

click “Next.”

WINDOWS PEER-TO-PEER NETWORK

5. Select the printer

manufacturer and the

printer model and click

“Next.” If your printer isn’t

on the list, click “Have

Disk…” to install the driver

of the printer. After

installation, the printer

model will be added to the

list.

6. Name your printer and set

the default printer; then

click “Next.”

7. The printer drivers are

being installed.

WINDOWS PEER-TO-PEER NETWORK

8. It is recommended that you

print a test page. Then

click “Finish.”

9. The printer is added to the Printers screen, indicating that you have added the

printer to your computer successfully. Now you can start to print from your

computer to the print server.

WINDOWS PEER-TO-PEER NETWORK

3.6.2 Windows XP

1. On the desktop, go to Start, then Settings: select “Printers and Faxes.”

2. Click “Add a Printer.”

3. The Add Printer Wizard”

screen is displayed. Click

“Next.”

4. Select “Local printer

attached to this computer”

and make sure that

“Automatically detect and

install my Plug and Play

printer” is not selected.

Click “Next.”

5. Choose the suitable “Print

Server Network Port”

created during the

Administrator Installation

or Client Installation

process and click “Next.”

WINDOWS PEER-TO-PEER NETWORK

6. Select a suitable printer

manufacturer and the

printer model and click

“Next.” If your printer isn’t

on the list, click “Have

Disk…” to install the driver

of the printer. After

installation, the printer

model will be added to the

list.

7. Name your printer and set

up the default printer; then

click “Next.”

8. It is recommended that you

print a test page. Then

click “Next.”

WINDOWS PEER-TO-PEER NETWORK

9. You have now successfully

added the printer to the PC.

Information about the

printer is displayed on

screen. Click “Finish.”

4. WindoWS nt/2000/Server 2003 netWork

4.1 System Architecture

In a Windows network environment, in addition to the Peer-to-Peer network

printing architecture described in the previous chapter, the 1-Port USB Wireless

Print Server also offers the server-based printing architecture for Windows NT/2000/

Server 2003. Only one Windows NT/2000/Server 2003 workstation is required to

have the Windows PTPP (Peer-to-Peer Printing) driver installed — it can share the

printing service on the network so other network users can simply connect to the

server and access the shared printer (see below).

4.2 Windows NT/2000/Server 2003 Installation and Setup

The following procedure is for the installation and construct of a peer-to-peer

connection (PTPP) between Windows NT/2000/Server 2003 and the print server.

1. If this is your rst time installing the print server, install the administrator software

on Windows NT/2000/Server 2003 rst. (Refer to section 3.2 for installation

instructions.)

NT/2000/SERVER 2003

If your network has already installed a working print server and your Windows

NT/2000/Server 2003 has not yet installed the PTPP driver, install the client

software. (Refer to section 3.4 and 3.5 for installation instructions.)

2. Add/congure the Peer-to-Peer Printing of the Windows NT/2000/Server 2003

network printer and verify that you can print from Windows NT/2000/Server 2003

to the print server through the installed PTPP driver.

3. Connect the above server’s printer to the network by performing the standard

Windows printer sharing process.

4.3 User Installation

After the server side’s installation

is complete, the client side will be

able to nd the server’s shared

printer in Network Neighborhood.

You only need to perform

Window’s standard Add New

Printer procedure, select

“Network Printer” (as shown at

below right), and complete the

congurations afterward to

access the shared printer.

NT/2000/SERVER 2003

5. netWare netWork

5.1 System Architecture

A NetWare printer sharing functionality has been integrated into the 1-Port USB

Wireless Print Server itself, thus allowing one or more printers attached by a print

server to be connected to the network. (The 1-Port USB Wireless Print Server

supports the NetWare print server.) This embedded print server emulates the “queue

management functionality” of a NetWare print server (the PSERVER program

running on the NetWare server). A user rst prints a job at a workstation, the job

is routed to a NetWare server, the NetWare server stores the job in a print queue

and then the print server gets the print job from the queue to printers.

Compared with NetWare printing functionality, the advantages of embedding the

NetWare network printing functionality in the 1-Port USB Wireless Print Server

include:

• Installation is easier and quicker.

• Network management is easier.

• Printing performance is enhanced.

• The NetWare le server’s burden is lessened.

• The need for a workstation running the remote printer utility is removed.

• Productivity is improved by locating the printer near the workgroup.

Each print server should log in to a NetWare server before servicing the print jobs,

and each print server will occupy a user account with which it can log in to the

NetWare server

5.2 NetWare 3.x/4.x/5.x Installation & Setup

Once your print server is connected to your Ethernet network, you can set it up for

use with your networking software.

5.2.1 Installation Using PCONSOLE (Conguring as Print Server Mode)

1. Run the NetWare PCONSOLE program.

2. Change the current le server, if necessary, using the “Change Current File

Server” menu selection.

3. Choose the “Print Queue Information” menu selection.

4. Press the Insert key to add a new print queue.

5. Enter a print queue name, such as “PQ” or “Q1.”

Netware Server

Windows 98

Windows 2000

Print Queue

Print Server

NT/2000/SERVER 2003

6. You’ve now successfully created

the print queue that your print

server will serve. Press the

Escape key until the Available

Options main menu is displayed.

7. Select “Print Server Information.”

8. Press the Insert key to add a new

NetWare print server object. The

print server name can be identical

to the PSxxxxxx name printed on

the label of the print server.

9. Press Enter to select the newly

created print server.

10. Select “Print Server

Conguration.”

11. Select “Printer Conguration.”

12. Select “Printer 0” (or “Printer 1,”

“Printer 2”) and press Enter, then

select “P1” (or “P2,” “P3”) in the

“Type” eld. NOTE: If your print

server has only one port, you do

not need to congure this eld.

13. Press Escape, and answer

“Yes” to the “Save Changes?”

prompt.

14. Select “Queues Serviced by

Printer,” then select “Printer 0”

(or “Printer 1,” “Printer 2”) and

press Enter.

15. Press Insert and add your

newly created print queue to

the list of queues serviced by

the printer. Enter a priority

number for the queue service,

or press Enter to accept the

default.

16. Repeatedly press Escape to

exit the PCONSOLE program.

17. Reset the print server so the changes take effect.

NOTE: If the print server you have has multiple printer connectors, you may create

multiple print queues and printer objects. Your print server should now be ready to

use. You should be able to redirect printing to your print server using a CAPTURE

command such as the one shown in the previous section.

NT/2000/SERVER 2003

6. UniX SyStem netWork

6.1 Introduction

The print server is available for TCP/IP printing by Unix LPD (Line Printer Daemon)

protocol. The LPD protocol, which originated with the Unix release, is based on the

BSD version of Unix and is supported under most versions of Unix.

This chapter explains how to congure the print server for TCP/IP operation, and

how to modify conguration les on your Unix system to allow printing to the print

server. The conguration examples in this manual follow the syntax for BSD-based

Unix systems. Refer to the related system documentation for the correct syntax of

your systems.

The ve steps below, which are detailed in the following sections, show how to

congure the print server for LPD printing.

1. Enable the print server’s TCP/IP support.

2. Set up the print server’s IP address.

3. Verify the print server’s IP address.

4. Congure remote LPD printing on the host.

5. Print a test page.

6.2 Enable the Print Server’s TCP/IP Support

The default conguration of the print server is set with TCP/IP support enabled.

You can congure the print server to enable TCP/IP support using the conguration

program.

6.3 Set Up the Print Server’s IP Address

The print server must have a unique IP address in order to be recognized by the

network. You can set up the IP address on the various Unix systems using either:

• DHCP (Dynamic Host Conguration Protocol) or

• BOOTP (Bootstrap Protocol)

6.3.1 DHCP

There are many Unix systems that support the DHCP protocol, and the procedures

to congure the DHCP server database are different. This manual does not

describe the DHCP server conguration on the Unix systems. It is highly

recommended that the DHCP server should be located on the same network as

the print server.

6.3.2 BOOTP

If you have the BOOTP daemon, bootpd, running on your UNIX system that is

accessible by the print server, you can use the BOOTP protocol to set up the IP

address of the print server. It’s recommended that the BOOTP server should be

located on the same subnet as the print server. If you use Network Information

Services (NIS) in your system, you may need to rebuild the NIS map with the

BOOTP services before doing the following BOOTP conguration. To rebuild the

NIS map, refer to your system documentation.

To congure the IP address data for the BOOTP server, you will need to log in the

host of the BOOTP server as the superuser (root). Perform the following steps to

add address entries.

UNIX

1. Optionally, assign a name corresponding to the print server’s IP address. You can

add this address to the /etc/hosts le by adding a line such as:

203.66.191.12 pserver

2. Add an entry to the host’s /etc/bootptab le, similar to the following:

hostname:\

:ht=1:\

:ha=print_server_ethernet_address:\

:ip=print_server_ip_address:

Lines should be indented with tabs.

Where the hostname is the device name of a print server, the ht=1 tag species

the hardware type is Ethernet; the ha= tag species the Ethernet address of a

print server, which is the node ID located on the print server. The ha tag must be

preceded by the ht tag. The ip= tag should correspond to the IP address you want

to assign to the print server.

For example, for a print server with the following conguration:

• Node ID: 0000B4010101 (this implies the Ethernet address is 0000B4010101),

• IP address: 203.66.191.12

the entry for this print server in the /etc/bootptab le should be:

PS010101:\

:ht=1:\

:ha=0000B4010101:\

:ip=203.66.191.12:

6.4 Verify the Print Server’s IP Address

To verify that your print server is responding to the newly assigned IP address

using a PING command:

ping ip-address

6.5 Congure Remote LPD Printing on the Host

The procedure you use to congure your Unix host(s) to allow printing to your

network remote print server varies among different varieties of Unix. The procedure

below can be used for Unix variants that are related to BSD Unix, such as SunOS

or Linux. For other versions of Unix, consult your system documentation, keeping

in mind that:

• The print server should be treated as a BSD-networked print server host.

• The hostname should be the name (or IP address) that you have assigned to the

print server.

• The printer name (or queue name) on the remote host should be p1, p2 or p3 —

the name of the printer port on the print server.

You will need to perform the tasks below, logged in as the superuser (root). To

congure your Unix host for printing,

1. Optionally, assign a name corresponding to the print server’s IP address. You can

add this address to the /etc/hosts le, by adding a line such as:

203.66.191.186 pserver

2. Create a spool directory for the printer in the same directory where spool

directories are normally kept on the machine, such as /var/spool or /var/spool/lpd:

UNIX

mkdir /var/spool/lpd/pserverd

chown daemon /var/spool/lpd/pserverd

chgrp daemon /var/spool/lpd/pserverd

chmod 775 /var/spool/lpd/pserverd

3. Add an entry to the host’s /etc/printcap le, similar to the following:

printer-name:\

:lp=:\

:rm=203.66.191.186:\

:rp=p1:\

:lf=/var/spool/lpd/pserverd.log:\

:sd=/var/spool/lpd/pserverd:\

:mx#0:

Lines should be indented with tabs. More than one printer name can be used, with

variants separated by vertical bars (name1|name2).

The rm= entry should correspond to the IP address you have assigned to the print

server. You can also use a hostname if you’ve assigned one in the /etc/hosts le.

The sd= entry should correspond to the spool directory you created in the previous

step.

The rp= entry should correspond to the port name of the remote printer. The values

should be one of p1, p2 or p3, depending on the printer port.

The print server should now be available for printing from your Unix host

7. configUration Utility

7.1 Introduction

This chapter introduces the print server’s system conguration utility in a Windows

environment. This utility is automatically installed during the Windows Administrator

utility installation procedure (refer to sections 3.2 and 3.3).

This utility provides the most complete management and conguration functions

on the print server side. This utility only provides conguration functions for the

print server itself; it does not include conguration functions for the client side or

other le servers or NetWare servers in the network environment.

The Conguration utility provides the following conguration and management

functions (with detailed subsections that follow):

• Search Print Server: Search all available printer servers on the network.

• Print Server Status: Display print server network status.

• General Conguration: General information about the print server.

• TCP/IP Conguration: IP address and DHCP server conguration.

• NetWare Conguration: NetWare printing conguration.

• AppleTalk Conguration: AppleTalk protocol settings.

• Bonjour Conguration: Mac OSX protocol settings.

• SMB: Congure the SMB group name.

• SNMP Conguration: SNMP information conguration.

• Setup Wizard: Guide to all the settings.

• System Conguration: Print server network ability settings, rmware upgrades

and language settings.

• Wireless Conguration: Wireless LAN conguration.

• Report: List the status of all available print servers on the network.

CONFIGURATION UTILITY

7.2 Search for All Available Print Servers

Whenever you run the print server’s conguration utility, click on the Search

icon (left) on the tool bar. The conguration utility will be delayed for several

seconds because the utility is using the system’s available network protocols to

search for all print servers on the network. All available print servers will be listed

under “Server Group” on the left side of the screen. Select the print server you

would like to congure from the list. The system will, at the same time, display the

selected print server’s status on the right side of the screen.

CONFIGURATION UTILITY

7.3 Status of the Print Server

Click on the Status icon (left) on the tool bar to show the status of the current

selected print server on the right side of the screen.

Information displayed about the print server includes MAC ID, model type, rmware

version, status of each printer port, NetWare le server name, NetWare le server

polling interval, NetWare printer queue names, IP address, subnet mask, default

gateway, AppleTalk printer type, AppleTalk zone and print server printing ability.

Refresh the print server’s status by clicking on the Refresh icon (far left).

Restart the print server by clicking on the Reboot icon (near left).

CONFIGURATION UTILITY

7.4 Set Up the Print Server

Click on the Setup icon on the tool bar to show the setup items of the current

selected print server on the right side of the screen. Double-click one of the

icons to set up the selected print server. A screen will display to verify the user

name and password of the print server. The default values are as follows.

• User Name: admin

• Password: 1234

CONFIGURATION UTILITY

7.5 General Conguration

Double-click on the General

icon and the General

conguration screen will

display. You can see basic

print server information on

this screen. You also can

congure the server name,

username and password here.

Server Name is the name

of the print server. You can

use this name to identify the

print server when you are

searching for the print server

using the administration and

client utilities.

User Name / Password is

used to authenticate the administrator using the Web administration tool.

7.6 TCP/IP Conguration

Double-click on the TCP/IP

icon and the TCP/IP

conguration screen will

display. You can congure the

print server to automatically

get an IP address from DHCP

server or manually specify a

static IP. The print server also

has a built-in DHCP server.

You can enable this DHCP

server and let it manage IP

addresses for you.

Click “IP” to enter the IP

settings page. If you need the

print server to automatically

get an IP address from the

DHCP server, select “Auto IP.”

You also can select “Static IP”

to manually assign an IP

address, subnet mask and

gateway for the print server.

Click “DHCP Server” to enter

the DHCP server’s settings

page. You can enable/disable

the DHCP server, or set to

“Auto” and assign a range of

IP addresses here. The DHCP

server is disabled by default.

CONFIGURATION UTILITY

If “Auto” is selected, the DHCP server of the print server will be enabled only when

there is no other DHCP server within the network. When “Enable” or “Auto” is

selected, you need to congure starting address, range, subnet mask, gateway

and DNS. The print server will assign a unique IP address for each client.

7.7 NetWare Print Server Conguration

Double-click on the NetWare

icon and the NetWare

conguration screen will

display. This print server

supports NetWare Bindery

Printing. The print server

periodically polls the

NetWare server printer

queues for printing jobs. You

need to assign the NetWare

server name, print server

polling interval and the name

of the queue on the NetWare

server for each printer port.

Polling Time is the polling

interval of the print server waiting for printing jobs on the NetWare server.

Queue Serviced by Printer is the name of the printer queue on the NetWare server.

The printer queue keeps all printing jobs waiting on the NetWare server. You need

to assign a printer queue for each printer port of this print server.

NetWare Server is the name of the NetWare le server that provides printer queues.

7.8 AppleTalk Conguration

Double-click on the AppleTalk

icon and the AppleTalk

conguration screen will

display. AppleTalk is a data

communication protocol often

used by Macs. The print

server can use these

parameters to join the

AppleTalk network and share

the printer to other AppleTalk

workstations. You need to

set up the zone name and

printer type for each printer

port of this print server.

Zone Name: The print

server has to join zones of AppleTalk before it can be shared with other workstations:

Only workstations in the same zone can share the printer. To share the printer with

all workstations in all zones, enter only an asterisk (*) in the “Zone Name” eld.

Printer Type is the type of printer attached to each printer port. You can get the

printer type from the manufacturer of the printer.

CONFIGURATION UTILITY

7.9 Bonjour Conguration

Bonjour enables

automatic discovery

of computers,

devices and services

on an IP network.

The service name

will be seen by users

on the IP network,

so choose a unique

(but recognizable!)

name to describe

the device.

7.10 SNMP Conguration

Double-click on the SNMP

icon and the SNMP

conguration window will

display.

Contact: You can enter the

print server administrator’s

contact information here.

This information will be

displayed in the SNMP

management tool.

Location: You can enter the

installed location of the print

server here. This information will be displayed in the SNMP management tool.

7.11 SMB Conguration

SMB Group Name is the

name of SMB group that this

print server belongs to. All

PCs should join the same

group before they can use

this print server using the

SMB protocol.

CONFIGURATION UTILITY

7.12 System Conguration

Double-click on the System icon and the System conguration window will display.

On the System conguration screen, you can enable/disable each printing or

management protocol, assign a name for each printer port of this print server,

upgrade the new rmware for this print server and enable/disable the wireless

function.

Port Name is the name of the printer port. Each printer port has to be assigned a

name. The client utility uses this name to access the printer port.

Upgrade Firmware: You can use this Upgrade Firmware tool to update the newest

rmware of the print server. Click and select the correct rmware in your PC.

After selecting the rmware le, click “Upgrade” to nish the rmware update

process. If you want to reset the print server to the default factory settings, click

“Load Default.”

Wireless Function: You can select “Enable” or “Disable” to manually enable or

disable the wireless function. If you manually enable the wireless function, the print

server’s wireless LAN will be always enabled and Ethernet will be always disabled.

CONFIGURATION UTILITY

If you manually disable the wireless function, the print server’s wireless LAN will be

always disabled and Ethernet will be always enabled. You also can select “Auto” to

let the print server automatically decide to enable or disable the wireless function.

The print server only can work in ether Ethernet or wireless LAN mode: It cannot

work in both Ethernet and wireless LAN mode at the same time. When the print

server starts up, it will auto-detect if the LAN port is connected to an active network

by an Ethernet cable. If the print server is connected to an active network through

an Ethernet cable when starting up, the print server will run in Ethernet mode. If

the print server is not connected to an active network by Ethernet cable when

starting up, the print server will run in wireless LAN mode. The print server default

is in “Auto” mode.

Domain Country: The wireless channels vary from country to country. Generally,

the channels are from 1 to 11 in the U.S. and from 1 to 13 in Europe. The operating

channel will be set to the print server before importing. If you are in a different

locale, make sure that you have set the available channels according to your

location.

7.13 Wireless Conguration

If you want to use the print server through a wireless LAN, set up the print server

through Ethernet rst and make sure your wireless LAN setting is correct. After

setting the wireless LAN, unplug the Ethernet cable and restart the print server;

then you can start to use the print server through the wireless LAN. NOTE: If the

wireless conguration doesn’t work, plug the Ethernet cable in again, restart the

print server and congure the print server through Ethernet until the wireless LAN

settings are correct.

The default settings of the print server wireless function are as follows.

• Mode: Infrastructure

• SSID: Default

• Channel: 11

CONFIGURATION UTILITY

Double-click on the Wireless icon and the wireless conguration window will display.

If you use access points to create a wireless network, Infrastructure mode is used.

After selecting the operation modes of the wireless function, click “Next” to display

detailed conguration information.

Infrastructure Mode

In Infrastructure mode, you need to let the print server associate with an access

point. The print server can scan for an available access point automatically or you

can manually assign the SSID of the access point you want to use.

If you elect to let the print

server scan for an available

access point, the screen at

right will display. The list is

of the scanned available

access points. Select an

access point on the list and

click “Next.” If you can’t nd

the access point that you

want to use, click “Scan” to

let the print server scan

again.

The following procedures are necessary to continue with the conguration of the

Infrastructure mode settings.

CONFIGURATION UTILITY

This print server supports WEP, WPA-PSK and WPA2-PSK security modes. To

use WEP encryption to protect your wireless network, select “WEP(ASCII)” or

“WEP(HEX).” To use WPA-PSK, select “WPA-PSK.” To use WPA2-PSK, select

“WPA2-PSK.” The wireless security setting should be the same on other wireless

devices in the same network.

WEP Security Mode

Select “64 bit” or “128 bit” length and “Hexadecimal” or “ASCII” format for the

encryption key. NOTE: A longer key length can provide stronger security, but at

the expense of communication performance.

CONFIGURATION UTILITY

Enter four key values using the guidelines below and select one key as the default

key.

PassPhrase: A passphrase simplies the WEP encryption process by automatically

generating the WEP encryption keys for the print server. This setting is only valid

when the security mode is “WEP(HEX).”

Key 1 — Key 4: If the key length is 64-bit, enter 10-digit Hex values or 5-digit

ASCII values as the encryption keys. For example: “0123456aef” or “Guest.” If the

key length is 128-bit, enter 26-digit Hex values or 13-digit ASCII values as the

encryption keys. For example: “01234567890123456789abcdef” or “administrator.”

WPA-PSK Mode

“WPA-PSK” requires users to select the advanced encryption methods — TKIP or

AES — and enter a set of shared keys.

CONFIGURATION UTILITY

TKIP: The Temporal Key Integrity Protocol (TKIP) changes the temporal key every

10,000 packets. This ensures much greater security than standard WEP security.

AES: AES has been developed to ensure the highest degree of security and

authenticity for digital information. It’s the most advanced solution dened by IEEE

802.11i for security in the wireless network.

Pre-shared Key Format: Select “Passphrase” or “Hex” key format. If “Passphrase”

is selected, enter 8 to 63 digits of ASCII format as the key for authentication within

the network. If “Hex” is selected, enter 64 digits of Hex code (“0-9” and “A-F”).

WPA2-PSK Mode

“WPA2-PSK” requires that you select the advanced encryption methods — TKIP

or AES — and enter a set of shared keys.

AES: AES has been developed to ensure the highest degree of security and

authenticity for digital information. It’s the most advanced solution dened by IEEE

802.11i for security in the wireless network.

Key: Enter 8 to 63 digits of ASCII format as the key for authentication within the network.

When you nish conguring the wireless security, click “Next” to continue.

You can elect to let the print

server automatically obtain

IP settings with DHCP Client

or to manually assign the IP

settings.

If you manually assign the

IP settings, you need to

enter the IP address, subnet

mask and default gateway

address.

When you nish conguring

the IP settings, click “Next”

to conrm the IP address

conguration.

CONFIGURATION UTILITY

Click “Save” to save the

wireless conguration.

7.14 Wizard

Click on the Wizard icon (left) on the tool bar to display the setup wizard item

of the current selected print server on the right side of the screen. Double-

click on the Print Server Setup Wizard and the setup wizard will guide you through

the entire setup process.

CONFIGURATION UTILITY

1. Set up the name

of this print

server and the

port name for the

print server, and

choose to enable

or disable the

wireless function.

2. Select/enable the

required printing

protocol (refer to section

7.12 for details).

3. Set up the IP address of

this print server and the

DHCP server (refer to

section 7.6 for details).

CONFIGURATION UTILITY

4. Set up the NetWare

printing (refer to section

7.7 for details).

5. Select the Wireless

Adapter mode and

complete the wireless

LAN settings. NOTE:

The other procedures

are the same as the

“Wireless” settings on

the Setup screen (refer

to section 7.13 for

details).

6. Click “Save” to

nish the

procedure.

CONFIGURATION UTILITY

7.15 Report

Click on the Report icon (left) on the tool bar to display the Report screen.

The report lists basic information about all available print servers on the

network, including device name, MAC ID, model type, rmware version and the

status of the print server.

8. WeB management

8.1 Introduction

The 1-Port USB Wireless Print Server can be congured and managed on the Web.

Through a local area network, or even the Internet, an administrator can easily

congure and manage the print server’s various main functions in browsers. Simply

enter the print server’s IP address into your browser’s address eld to manage a

print server using the print server’s built-in Web server.

The default IP address, username and password settings of the print server are as

follows.

• IP Address: 192.168.2.2

• User Name: Admin

• Password: 1234

8.2 Login

You can use any Web browser to review

the status or congure the settings of the

print server. After entering the IP address

of the print server, a login page displays

(right). Make the correct entries in the

“User Name” and “Password” elds, then

proceed to the Web Management pages.

WEB MANAGEMENT

8.3 Device Status

8.3.1 System

System Information includes the device name, print server name, model type,

system up time, rmware version, MAC address and the status of the protocols

enabled.

8.3.2 Printer

This screen lists information about the printer connected to the printer port.

WEB MANAGEMENT

8.3.3 TCP/IP

This screen lists all TCP/IP settings of the print server, including the IP address,

subnet mask and gateway. It also lists DHCP server settings.

8.3.4 SMB

This screen lists the SMB group settings of the print server.

WEB MANAGEMENT

8.3.5 SNMP

This screen lists the SNMP settings of the print server, including the SNMP system

contact and SNMP system location.

SNMP System Community: To enter the name of the system group. The default

name is “public.”

SNMP System Manager IP: The IP address for the trap alarm.

SNMP Trap: There are two levels to choose from: v1 and v2.

8.3.6 NetWare

This screen lists NetWare settings, including polling time, Bindery mode settings,

name of the le server and port attached queue.

WEB MANAGEMENT

8.3.7 AppleTalk

This screen lists AppleTalk settings, including the AppleTalk zone name and the type

of printers connected to all print ports.

8.3.8 Bonjour

This screen lists Bonjour settings, including the port service name of each port.

WEB MANAGEMENT

8.4 Setup Wizard

8.4.1 System

You can change the print server name and port name of the print server from here.

Print Server Name is the name of the print server. You can use this name to

identify the print server when you are searching for the print server by the

administrator and client utilities.

Port Name is the name of the printer port. Each printer port has to be assigned a

name to be used to access the printer port.

8.4.1.1 Admin Password

This screen allows you to change the password of the print server.

WEB MANAGEMENT

Name is the administrator name of the print server. If you change the name, you

need to log in to the print server from the administrator utility or Web management

with the new name. The default user name is “admin.”

Password: Enter the password you want to change for the print server. The

password can be up to an 8-digit alphanumeric format. The default password is

“1234.”

Re-type Password: Enter the password you want to change for the print server

again.

8.4.1.2 Advanced Settings

This screen allows you to enable/disable the printing protocol.

To enable the function, select “Enable”; to disable the function, select “Disable.”

8.4.2 Wireless

If you want to use the print server through a wireless LAN, set up the print server

through the Ethernet rst and make sure your wireless LAN setting is correct. After

setting the wireless LAN, unplug the Ethernet cable and restart the print server.

You can then start to use the print server through the wireless LAN. If the wireless

conguration doesn’t work, plug the Ethernet cable in again, restart the print server

and congure the print server through the Ethernet until the wireless LAN settings

are correct.

You can set parameters that are used for the wireless stations — including Function

and ESSID — to connect to this print server. You can manually set the parameters

of a wireless LAN on this screen or use the Site Survey function to automatically

search for an available access point and associate with it.

Mode is the operation mode of wireless station. If you’re using an access point in

the wireless LAN infrastructure, the wireless mode is Infrastructure.

ESSID is the unique name identifying a wireless LAN. The ID prevents the

unintentional merging of two co-located WLANs. Make sure that the ESSID of all

WEB MANAGEMENT

stations and access points in the same WLAN network is the same.

Channel Number is the channel number of your wireless LAN. The channel

number is set to “11.”

8.4.2.1 Site Survey

This screen allows you to search for available access points in your location.

On the list is information about all available access points or wireless stations,

including SSID, BSSID, channel, type, encryption and signal strength. You can

select one wireless device on the list for this print server to associate with.

WEB MANAGEMENT

8.4.2.2 Encryption

This print server supports WEP, WPA-PSK and WPA2-PSK security modes. To

use WEP encryption to protect your wireless network, select “WEP.” To use WPA-

PSK, select “WPA-PSK.” To use WPA2-PSK, select ‘’WPA2-PSK.’’ The wireless

security setting should be the same for other wireless devices in the same network.

WEP Security Mode

Key Length: Choose “64-bit” to use WEP with 64-bit key length encryption; choose

“128-bit” to use WEP with 128-bit key length encryption. NOTE: A longer key

length can provide stronger security, but at the expense of throughput.

Key Format: Use ASCII characters (alphanumeric format) or hexadecimal digits

(in the “A-F,” “a-f” and “0-9” ranges) for the WEP key.

PassPhrase: A passphrase simplies the WEP encryption process by automatically

generating the WEP encryption keys for the print server.

Default Key: Select one of the four keys to encrypt your data. Only the key you

select in the “Default key” drop-down menu will take effect.

Key 1 – Key 4: The WEP keys are used to encrypt data transmitted within the

wireless network. If the key length is 64-bit, enter 10-digit Hex values or 5-digit

ASCII values as the encryption keys. For example: “0123456aef” or “Guest.” If the

key length is 128-bit, enter 26-digit Hex values or 13-digit ASCII values as the

encryption keys. For example: “01234567890123456789abcdef” or “administrator.”

WEB MANAGEMENT

WPA-PSK Security Mode

“WPA-PSK” requires that you select one of the advanced encryption methods —

TKIP or AES — and enter a set of shared keys.

TKIP: The Temporal Key Integrity Protocol (TKIP) changes the temporal key every

10,000 packets. This ensures much greater security than standard WEP.

AES: AES has been developed to ensure the highest degree of security and

authenticity for digital information. It’s the most advanced solution dened by IEEE

802.11i for security in the wireless network.

Pre-shared Key Format: Select “Passphrase” or “Hex” key format. If “Passphrase”

is selected, enter 8 to 63 digits of ASCII format as the key for the authentication

within the network. If “Hex” is selected, enter 64 digits of Hex code (“0-9” and “A-F”).

Pre-Shared Key: Enter your encryption code in this eld.

WEB MANAGEMENT

WPA2-PSK Security Mode

“WPA2-PSK” requires that you enter shared keys with AES algorithms only.

AES: AES has been developed to ensure the highest degree of security and

authenticity for digital information. It’s the most advanced solution dened by IEEE

802.11i for security in the wireless network.

Pre-shared Key Format: Select “Passphrase” or “Hex” key format. If “Passphrase”

is selected, enter 8 to 63 digits of ASCII format as the key for the authentication

within the network. If “Hex” is selected, enter 64 digits of Hex code, (“0-9” and “A-F”).

When you nish conguring the wireless security, click “Save & Next” to conrm

the conguration.

8.4.3 TCP/IP

WEB MANAGEMENT

You can congure the print server to automatically get an IP address from the

DHCP server, or to manually specify a static IP address. The print server also has

a built-in DHCP server. You can enable this DHCP server and let it manage the IP

process for you.

If you need the print server to automatically get an IP address from the DHCP

server, select “Enable Obtain TCP/IP Settings Automatically (Use DHCP/ BOOTP).”

You also can select “Disable Use the following TCP/IP Settings” to manually assign

an IP address, subnet mask and gateway for the print server.

You can enable/disable or set to “Auto” for the print server’s DHCP server. The

DHCP server is disabled by default. If the DHCP server is enabled or set to “Auto,”

you need to assign a range of IP addresses here. Fill in the “Start IP,” “Range,”

“DNS,” “Subnet Mask” and “Gateway” elds, and the print server will assign a

unique IP for each client. NOTE: When “Auto” is selected, the DHCP server of the

print server will be enabled only when there is no other DHCP server within the

network.

8.4.4 SMB

You can enable/disable the SMB protocol from here. If SMB is enabled, enter the

SMB group name to specify the SMB group that this print server belongs to. All

PCs should join the same group before they can use this print server using the

SMB protocol. Furthermore, you can enable the “Pass Job When Error Occurred’’

function and enter the time length (1-60 seconds) in the “Waiting time to pass job’’

eld.

WEB MANAGEMENT

8.4.5 SNMP

The print server supports SNMP conguration. If it’s enabled, set up the following

parameters.

SNMP System Contact: You can enter the print server administrator’s contact

information here. This information will be displayed in the SNMP management tool.

SNMP System Location: You can enter the installed location of the print server

here. This information will be displayed in the SNMP management tool.

SNMP System Community: To enter the name of the system group. The default

name is “public.”

SNMP System Manager IP: The IP address for the trap alarm.

SNMP Trap: There are two levels to choose from: v1 and v2.

8.4.6 NetWare

This print server supports the NetWare Bindery Printing method. The print server

WEB MANAGEMENT

periodically polls the NetWare server printer queues for printing jobs. You have

to assign the NetWare server name, print server polling interval and the name of

queue on the NetWare server for each printer port.

Polling Time is the polling interval of the print server for waiting printing jobs on

the NetWare server.

Name of the File Server is the name of the NetWare le server that provides

printer queues.

Attached Queue is the name of the printer queue on the NetWare server. The

printer queue keeps all printing jobs waiting on the NetWare server. You need to

assign a printer queue for each printer port of this print server.

8.4.7 AppleTalk

AppleTalk is a data communication protocol often used by Macs. The print server

can use these parameters to join the AppleTalk network and share the printer to

other AppleTalk workstations. You need to either enable or disable AppleTalk and

set up the zone name and printer type for each printer port of this print server.

AppleTalk Enable: Enable or disable AppleTalk.

AppleTalk Zone Name: The print server has to join zones of AppleTalk before it

can be shared with other workstations. Only workstations in the same zone can

share the printer. If you want to share the printer with all workstations in all zones,

enter only and asterisk (*) in the “Zone Name” eld.

Printer Type is the type of printer attached to each printer port. You can get the

printer type from the manufacturer of the printer.

WEB MANAGEMENT

8.4.8 Bonjour

Bonjour enables automatic discovery of computers, devices and services on an IP

network. The service name will be seen by users on the IP network, so choose a

unique (but recognizable!) name to describe the device.

8.4.9 Save Settings

Click “Save Settings” to save the settings and restart the system.

WEB MANAGEMENT

8.5 System Tools

8.5.1 Load Default

You can use this screen to restore the factory default settings. All of your previous

setup will be cleared.

8.5.2 Upgrade Firmware from Browser

You can upgrade new rmware for the print server on this screen.

Click “Browse” to select the new rmware in your storage, then click “OK.” The

rmware will be updated in several minutes. NOTE: Once you’ve started upgrading

the rmware, you need to follow all the upgrading steps or the print server can’t return

to its normal conguration.

WEB MANAGEMENT

Browse

8.5.3 Backup Settings

To back up the print server settings to a “cong.bin” le, select “Backup settings

from Print Server.”

8.5.4 Restore System

To apply the settings from the backup le, select “Restore settings from le” and

specify a le to restore.

WEB MANAGEMENT

Browse

8.5.5 Language

To apply the language you want to use, select “TW” for Chinese or “EN” for

English; then click “OK.”

9. telnet management

9.1 Introduction

The 1-Port USB Wireless Print Server an be congured and managed by Telnet.

Through a local area network, or even over the Internet, an administrator can

easily congure and manage the print server’s various main functions using a

Telnet client tool.

9.2 Login

Execute the Telnet client tool and connect to the print server’s IP address:

telnet 192.168.2.2

You’ll then be prompted to enter the username and password.

After you enter the correct username and password, an “admin#” prompt will be

displayed, indicating that you can start to manage the print server by command.

TELNET MANAGEMENT

9.3 Get Setting Values – The ‘get’ Command

The “get” command (formatted as: get argument [value] — see the table below) is

used to get the setting values of the print server. For example, to get the IP address

of the print server, type the “get ip” command after the “admin#” prompt. The IP

value “IP_ADDR=’192.168.2.2’” will be displayed:

admin# get ip



IP_ADDR=’192.168.2.2’

If you enter “get” only, the system will list all available arguments for the “get”

command, as presented in the following table.

Argument Description Example

psname Print server name admin# get psname

PORT1_PS=’PS254896’

password Login password admin# get password

USER_PASSWORD=’1234’

username Login username admin# get username

USER_NAME=’admin’

wlfunc Wireless LAN function is enabled

or disabled

0: disabled

1: enabled

2: auto

admin# get wlfunc

WIRELESS_FUNCTION=2

wlmode Wireless LAN mode is

Infrastructure

0: Infrastructure

admin# get wlmode

AP_MODE=1

ESSID ESSID of the wireless LAN admin# get ESSID

SSID=’default’

channel Channel number used by wireless

LAN

admin# get channel

CHANNEL=11

wep The mode of WEP

0: disable

1: 64 bit WEP enabled

2: 128 bit WEP enabled

admin# get wep

WEP=0

defkey Default WEP key number

0: key 1

1: key 2

2: key 3

3: key 4

admin# get defkey

WEP_DEFAULT_KEY=0

key641 64 bit WEP key 1 admin# get key641

WEP64_KEY1=0123456789

key642 64 bit WEP key 2 admin# get key641

WEP64_KEY2=0123456789

key643 64 bit WEP key 3 admin# get key641

WEP64_KEY3=0123456789

key644 64 bit WEP key 4 admin# get key641

WEP64_KEY4=0123456789

key1281 128 bit WEP key 1 admin# get key1281

WEP128_KEY1=0123456789

abcdef0123456789a

key1282 128 bit WEP key 2 admin# get key1282

WEP128_KEY2=0123456789

abcdef0123456789a

key1283 128 bit WEP key 3 admin# get key1283

WEP128_KEY3=0123456789

abcdef0123456789a

key1284 128 bit WEP key 4 admin# get key1284

WEP128_KEY4=0123456789

abcdef0123456789a

ip IP of the print server admin# get ip

AP_ADDR=’192.168.2.2’

gateway Default gateway of the print server admin# get gateway

DEFAULT_

GATEWAY=’192.168.2.254’

TELNET MANAGEMENT

submask Subnet mask of the print server admin# get submask

SUBNET_MASK=’255.255.255.0’

polling Polling interval (in second) of the

print server for waiting printing

jobs on the NetWare server

admin# get polling

PORT1_POLLTIME=3

aq1 Name of the printer queue on the

NetWare server

admin# get aq1

PORT1_QNAME=’PQ1’

applezone The name of AppleTalk zone that

this print server joins to

admin# get applezone

PORT1_APPLEAONE=’*’

printertype1 The type of the printer attached to

this print server

admin# get printertype1

PORT1_

PRINTTYPE=’LaserWriter’

SMBDG The name of the SMB group

name that this print server joins to

admin# get SMBDG

SMBD_NAME=’default’

SNMPC The administrator contact

information of this print server for

SNMP

admin# get SNMPC

SNMP_CONTACT=’sbdjohn@

hotmail.com’

SNMPL The installed location of this print

server for SNMP

admin# get SNMPL

SNMP_LOCATION=’Room 301’

port1 The port name of this print server admin# get port1

PORT1_LPTNAME=’p1’p1’1’

DHCPS The DHCP server is enabled or

disabled

0: disable

1: enable

admin# get DHCPS

DHCPD=0

DHCP Get dynamic IP by DHCP is

enabled or disabled

0: disable

1: enable

admin# get DHCP

DYNAMIC_IP=0

appletalk AppleTalk printing is enabled or

disabled

0: disable

1: enable

admin# get appletalk

APPLE_ENABLE=0

SMBD SMB printing is enabled or

disabled

0: disable

1: enable

admin# get SMBD

SMBD_ENABLE=1

SNMP SNMP management protocol is

enabled or disabled

0: disable

1: enable

admin# get SNMP

SNMP_ENABLE=1

IPX NetWare Bindery printing is

enabled or disabled

0: disable

1: enable

admin# get IPX

IPX_ENABLE=1

LPD LPR printing is enabled or

disabled

0: disable

1: enable

admin# get LPD

LPD_ENABLE=1

IPP IPP printing is enabled or disabled

0: disable

1: enable

admin# get IPP

IPP_ENABLE=1

RAW RAW printing is enabled or

disabled

0: disable

1: enable

admin# get RAW

RAW_ENABLE=1

TELNET MANAGEMENT

9.4 Modify Setting Values – The ‘set’ Command

The “set” command (formatted as: set argument [name value] — see the table

below) is used to modify the print server setting values, which will be written into

the system conguration. For example, if you want to set the IP address of the print

server to 192.168.2.2, type “set ip 192.168.2.2” and the IP address of the print

server will be changed. After the setting is nished, reboot the print server (admin#

reboot).

If you enter “set” only, the system will list all available arguments for the “get”

command, as presented in the following table.

Argument Description Example

psname Print server name set psname PS001

password Login password set password 1234

username Login username set username admin

wlfunc Enable or disable the wireless

LAN function.

The value should be “disabled,”

“enabled” or “auto”

set wlfunc auto

wlmode Wireless LAN mode is

Infrastructure..

The value should be “inf”

set wlmode infrastructureinfrastructure

ESSID ESSID of the wireless LAN set ESSID default

channel Channel number used by wireless

LAN.

set channel 11

wep The mode of WEP.

The value should be “disable,”

“wep64” or “wep128”

set wep disable

defkey Default WEP key number.

The value should be 0–3.

0: key 1

1: key 2

2: key 3

3: key 4

set defkey 0

key641 64 bit WEP key 1.

The value should be 10-digit Hex

value

set key641 0123456789

key642 64 bit WEP key 2.

The value should be 10-digit Hex

value

set key641 0123456789

key643 64 bit WEP key 3.

The value should be 10-digit Hex

value

set key641 0123456789

key644 64 bit WEP key 4.

The value should be 10-digit Hex

value

set key641 0123456789

key1281 128 bit WEP key 1.

The value should be 26-digit Hex

value

set key1281 0123456789ab

cdef0123456789a

key1282 128 bit WEP key 2.

The value should be 26 digit Hex

value

set key1282 0123456789ab

cdef0123456789a

key1283 128 bit WEP key 3.

The value should be 26-digit Hex

value

set key1283 0123456789ab

cdef0123456789a

key1284 128 bit WEP key 4.

The value should be 26-digit Hex

value

set key1284 0123456789ab

cdef0123456789a

ip IP of the print server set ip 192.168.2.2

gateway Default gateway of the print server set gateway 192.168.2.254

submask Subnet mask of the print server set submask 255.255.255.0

TELNET MANAGEMENT

polling Polling interval (in second) of the

print server for waiting printing

jobs on the NetWare server

set polling 3

aq1 Name of the printer queue on the

NetWare server

set aq1 PQ1

applezone The name of AppleTalk zone that

this print server joins to

set applezone *

printertype1 The type of the printer attached to

this print server

set printertype1 LaserWriterLaserWriteraserWriter

SMBDG The name of the SMB group

name that this print server joins to

set SMBDG default

SNMPC The administrator contact

information of this print server for

SNMP

set SNMPC sbdjohn@hotmail.

com

SNMPL The installed location of this print

server for SNMP

set SNMPL Room 301

port1 The port name of this print server set port1 p1p11

DHCPS Enable or disable the DHCP

server.