509060 Manual

2009-10-12

: Pdf 509060 Manual 509060_manual 510 s

Open the PDF directly: View PDF .
Page Count: 76

Download
Open PDF In Browser	View PDF

1-Port
USB
Wireless
Print
Server
user
manual
Model 509060

INT-509060-UM-0508-01

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™ 1-Port USB Wireless Print
Server, Model 509060. Designed to work with any access point or peer-to-peer wireless network,
this server connects any USB printer to your network and is compatible with all major operating
systems. Its 10/100 Mbps Ethernet network port connection lets you operate wired or wireless,
and its pocket size makes it an easy fit in portable tool kits.
The easy-to-follow instructions in this user manual help make setup and operation relatively
simple. NOTE: Some screen images have been modified to fit the format of this manual.

safety & compliance statements
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC (Federal Communication Commission) Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from the receiver.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

This equipment must be installed and operated in accordance with provided instructions, and a
minimum of 20 cm spacing must be provided between the computer-mounted antenna and a
person’s body (excluding hands and feet) during wireless modes of operation. As this device
complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: 1)
This device may not cause harmful interference; and 2) this device must accept any interference
received, including interference that may cause undesired operation. Any changes or modifications
not expressly approved by the party responsible for compliance could void the authority to operate
equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. To avoid the possibility of exceeding these limits, human proximity to the antenna
shall not be less than 20 cm (8 inches) during normal operation. The antenna(s) used for this
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of Directive 1999/5/EC of the European
Parliament and the Council of March 9, 1999, on radio equipment and telecommunication terminal
equipment (R&TTE) and the mutual recognition of their conformity. The R&TTE directive repeals
and replaces Directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth
Station Equipment) as of April 8, 2000.

EU Countries Intended for Use

The ETSI version of this device is intended for home/office use in Austria, Belgium, Denmark,
Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal,
Spain, Sweden and the U.K., and is also authorized for use in EFTA member states Iceland,
Liechtenstein, Norway and Switzerland. (EU countries not intended for use: none.)
SAFETY & COMPLIANCE

Contents
1. Introduction................................................................................................................... 6

1.1 Network Printing Architecture...................................................................................... 6

1.1.1 Print Server Network Functions....................................................................... 6

1.1.2 Network Printing Functions for Clients............................................................ 6

1.1.3 Network Printing Functions for a Network Server........................................... 7

1.2 Network Printing Environment..................................................................................... 8
2. Hardware Installation.............................................................................................. 9
3. Windows Peer-to-Peer Network............................................................................ 9

3.1 System Architecture..................................................................................................... 9

3.2 Administrator Installation and Setup.......................................................................... 10

3.3 Administrator Utilities................................................................................................. 13

3.4 Client Installation and Setup...................................................................................... 14

3.5 Client Utilities............................................................................................................. 16

3.5.1 Network Ports Quick Setup.......................................................................... 17

3.5.2 Remote Ports Utility..................................................................................... 17

3.6 Windows Add Printer Procedure............................................................................... 19

3.6.1 Windows Vista.................................................................................................. 19

3.6.2 Windows XP..................................................................................................... 22
4. Windows NT/2000/Server 2003 Network.............................................................. 24

4.1 System Architecture................................................................................................... 24
4.2 Windows NT/2000/Server 2003 Server Installation and Setup................................. 24
4.3 User Installation......................................................................................................... 25

5. NetWare Network...................................................................................................... 26

5.1 System Architecture.................................................................................................. 26

5.2 NetWare 3.x/4.x/5.x Installation & Setup................................................................... 26

5.2.1 Installation Using PCONSOLE..................................................................... 26
6. UNIX System Network................................................................................................ 28

6.1 Introduction................................................................................................................ 28

6.2 Enable Print Server’s TCP/IP Support...................................................................... 28

6.3 Set Up the Print Server’s IP Address........................................................................ 28

6.3.1 DHCP ........................................................................................................... 28

6.3.2 BOOTP......................................................................................................... 28

6.4 Verify the Print Server’s IP Address.......................................................................... 29

6.5 Configure Remote LPD Printing on the Host............................................................. 29
7. Configuration Utility............................................................................................... 30

7.1 Introduction................................................................................................................ 30
7.2 Search for All Available Print Servers........................................................................ 31
7.3 Status of the Print Server........................................................................................... 32
7.4 Set Up the Print Server.............................................................................................. 33
7.5 General Configuration................................................................................................ 34
7.6 TCP/IP Configuration................................................................................................. 34
7.7 NetWare Print Server Configuration.......................................................................... 35
7.8 AppleTalk Configuration............................................................................................. 35
7.9 Bonjour Configuration................................................................................................ 36
7.10 SNMP Configuration.................................................................................................. 36
7.11 SMB Configuration.................................................................................................... 36
7.12 System Configuration................................................................................................ 37
7.13 Wireless Configuration.............................................................................................. 38

CONTENTS

7.14 Wizard......................................................................................................................... 43
7.15 Report.......................................................................................................................... 46

8. Web Management......................................................................................................... 46

8.1 Introduction.................................................................................................................. 46

8.2 Login........................................................................................................................... 46

8.3 Device Status............................................................................................................. 47

8.3.1 System.......................................................................................................... 47

8.3.2 Printer........................................................................................................... 47

8.3.3 TCP/IP.......................................................................................................... 48

8.3.4 SMB.............................................................................................................. 48

8.3.5 SNMP........................................................................................................... 49

8.3.6 NetWare....................................................................................................... 49

8.3.7 AppleTalk...................................................................................................... 50

8.3.8 Bonjour......................................................................................................... 50

8.4 Setup Wizard............................................................................................................. 51

8.4.1 System.......................................................................................................... 51

8.4.1.1 Admin Password............................................................................. 51

8.4.1.2 Advanced Settings......................................................................... 52

8.4.2 Wireless........................................................................................................ 52

8.4.2.1 Site Survey..................................................................................... 53

8.4.2.2 Encryption...................................................................................... 54

8.4.3 TCP/IP.......................................................................................................... 56

8.4.4 SMB.............................................................................................................. 57

8.4.5 SNMP........................................................................................................... 58

8.4.6 NetWare....................................................................................................... 58

8.4.7 AppleTalk...................................................................................................... 59

8.4.8 Bonjour......................................................................................................... 60

8.4.9 Save Settings............................................................................................... 60

8.5 System Tools............................................................................................................. 61

8.5.1 Load Default.................................................................................................. 61

8.5.2 Upgrade Firmware from Browser.................................................................. 61

8.5.3 Backup Setting.............................................................................................. 62

8.5.4 Restore System............................................................................................ 62

8.5.5 Language...................................................................................................... 63
9. Telnet Management.................................................................................................... 63

9.1
9.2
9.3
9.4
9.5

Introduction................................................................................................................... 63
Login...... ....................................................................................................................... 63
Get Setting Values – The ‘get’ Command................................................................... 64
Modify Setting Values – The ‘set’ Command.............................................................. 66
Other Commands........................................................................................................ 67

10. IPP Printing................................................................................................................... 68

10.1

10.2

Introduction................................................................................................................. 68
System Setup............................................................................................................ 68
10.2.1 Print Server Side........................................................................................... 68
10.2.2 Client Side..................................................................................................... 68

11. Windows XP SP2 Setup. ........................................................................................................70
12. specifications . ...................................................................................................................... 74

CONTENTS

1. introduction
1.1 Network Printing Architecture
By first introducing the roles of a print server, client user and network server in the
network-printing environment, this section illustrates how the 1-Port USB Wireless
Print Server — often referred to subsequently simply as “the print server” —
functions and operates on the network. Before you install and use the print server,
it is strongly recommended that you read this section completely, then select only
the chapters you
Network Printing Environment
need according to
your network
Network Server
Print Server
operating system.
Client
User
The print server
provides a complete
network printing
solution, including
Unix
Print Server
NetWare ServerWindows NT Server
peer-to-peer printing
(PTPP), TCP/IP
(LPR), IPP printing,
NetWare bindery
Windows NT Windows 2000 Windows 98
printing, AppleTalk
Workstation
and SMB printing.
1.1.1 Print Server Network Functions
Because the 1-Port USB Wireless Print Server
supports IPX/SPX, NetBEUI, TCP/IP and AppleTalk
network protocols, any networked computer can
directly print to it through any of its installed
protocols.

1.1.2 Network Printing Functions for Clients
The 1-Port USB Wireless Print Server provides a
PTPP (peer-to-peer printing) driver and utilities for
Windows 95/98SE/Me/NT/2000/XP/Server 2003/
Vista users. PTPP supports the TCP/IP protocol.

Print Server

Unix

INTRODUCTION

NetWare ServerWindows NT Server

Windows NT Windows 2000 Windows 98
Workstation

Client User

Unix

Windows NT Windows 2000 Windows 98
Workstation

Print Server

NetWare ServerWindows NT Server

In the client installation procedure, after the PTPP driver is installed in Windows,
the system will automatically (manual configuration is also allowed) search all the
print servers on the network and then add their printing ports into Windows’ printing
port (see below).

PTPP

Windows 98

Print Server
MIS-2

Print Server
MIS-1

UNIX (including HP/UX, SCO Unix, SunOS, Solaris, Unixware DECUnix, IBM AIX
and others) and Linux use the system-standard LPR to print through the print server.
MAC OS can use the system-standard AppleTalk network to print through the print
server.
Network Server

1.1.3 Network Printing Functions for a Network Server
The 1-Port USB Wireless Print Server provides a
PTPP driver and utilities for Windows NT/2000/
Server 2003/Vista. After PTPP is installed, the
server can directly print through the print server.
Adding this printing function to Windows allows many advanced features to be used,
such as print queue and user authority management.
Unix

Print Server

NetWare ServerWindows NT Server

Windows NT Windows 2000 Windows 98
Workstation

In a NetWare environment, the 1-Port USB Wireless Print Server offers various
printing modes, such as print queue, remote printer, etc.

INTRODUCTION

1.2 Network Printing Environment
In a Windows peer-to-peer network, the client’s PTPP driver will use the TCP/IP
protocol to print through the print server.

In a Windows NT/2000/Server 2003/Vista network, the network printing function
will become available after the PTPP driver is installed in Windows. As stated
earlier, adding this printing function
allows many advanced features to
be used, such as print queue and
user authority management.

In a NetWare network, the 1-Port USB Wireless Print Server offers various printing
modes, such as print queue, remote
printer, etc.

INTRODUCTION

2. hardware installation
1. Unpack the 1-Port USB Wireless Print Server package and verify that all the
items listed in the Package Contents section of the Specifications are provided.
2. Connect the print server to the printer you want to share on the network.
3. Connect the print server to your network by attaching the network cable to the
UTP port of the print server.
4. Connect the power adapter to the print server. The print server will perform the
Power-On-Self-Test (POST) after it is turned on. During the POST, the Status
LED will be on. When the LEDs are unlighted, the print server is ready.
NOTE 1: Only use the power adapter shipped with the print server. Do NOT use
any other power adapter from any other sources.
NOTE 2: To avoid a compatibility problem between the 1-Port USB Wireless Print
Server and some printers, it is recommended that you turn on power to the 1-Port
USB Wireless Print Server before turning on the printer.

3. windows peer-to-peer network
3.1 System Architecture
The print server supports Windows’ Peer-to-Peer Network Printing mode, which is
suitable for most medium and small network environments.

The installation procedure is separated into two parts:
1. Administrator Installation and Setup (refer to section 3.2 for more detailed info).
System administrators must:
• Install the administrator’s utilities into his/her computer.
• Configure the print server from the administrator’s configuration utility.
2. Client Installation and Configuration (refer to section 3.3 for more detailed info).
Client users must:
• Install a Windows PTPP driver for network printing.
In addition, after PTPP is installed, the system will automatically search for all
print servers on the network and add the printing port of the print servers into
Windows’ printing port (refer to Network Printing Architecture in section 1.1 for
more detailed information).

HARDWARE INSTALLATION / WINDOWS PEER-TO-PEER NETWORK

3.2 Administrator Installation and Setup
The Administrator Installation can be performed on Windows 98SE/Me/NT/2000/
XP/Server 2003/Vista with the same user interface. Before the installation, verify
that your network protocol is installed on your PC (TCP/IP, IPX and/or NetBEUI). It
will be helpful in your installation process.
Insert the CD included with
the print server into your
CD-ROM drive. The
Autorun.exe program should
be executed automatically.
If not, run Autorun.exe
manually from the CD-ROM
drive’s root directory. The
Installation Manager will be
displayed on the screen
(shown at right). Click
“Administrator Installation.”
The “Utilities Setup” window
will be displayed. Click
“Next.”

Click “Next” to install the
utilities in the default folder,
or click “Browse” to specify
the destination folder where
you would like to install the
utilities.

WINDOWS PEER-TO-PEER NETWORK

Select the components you
want to install. It is highly
recommended that you
install all of the provided
components. Click “Next” to
continue.

Specify the program folder
where the program icons
will be added. Click “Next.”

The system will start to
install the utilities
automatically.

WINDOWS PEER-TO-PEER NETWORK

At this point, the installation
phase is complete. You can
prepare to configure the
print server. The “Choose
Print Server” field will list all
print servers within the
network. Select the print
server you would like to
configure and click “Next.”
NOTE 1: If this is the first
time you configure the print
server, the “Print Server
Name” is the last 6 digits of
the MAC ID with the prefix
“PS.” Check the MAC ID on
the print server.
NOTE 2: The list can only display the devices from the same manufacturer.
Specify a recognizable
name for the print server
and click “Next.”

Specify the IP address for
the print server manually or
click “Next” to keep the
default IP address:
192.168.2.2.

WINDOWS PEER-TO-PEER NETWORK

The configuration summary
is displayed.Now, you have
completed the print server
setup. Click Finish” and
your system will add a
network port of the print
server to your PC
automatically.

At this point, the administrator
installation procedure is
done. Click “Finish.”

The Administrator Installation program performs the following tasks:
• Installs all utilities and drivers to the administrator’s PC.
• Configures the print server (including the print server name and network protocol).
• Adds the network port of the print server to the administrator’s PC.
If you want to print from this administrator’s PC to the print server, all you need to
do is to perform Windows’ standard Add Printer procedure (refer to Section 3.6).

3.3 Administrator Utilities
After the Administrator Installation program is completed, there will be four utilities
in the print server’s Program folder.
Network Ports Quick Setup – Adds the network ports of print servers within the
network to your PC.
Print Server Configuration – Allows you to configure the print server’s IP address,
network protocols and other advanced functions. (Refer to Chapter 7 for detailed
instructions for the configuration.)
Remote Ports – Adds the network port of a remote printer server to your PC.

WINDOWS PEER-TO-PEER NETWORK

Uninstall – This “assistant”
serves to remove all
installed administrator
software.

3.4 Client Installation and Setup
The Client Installation program can be performed on Windows 98SE/Me/NT/2000/
XP/Server 2003/Vista with the same user interface. Before starting the installation
procedure, confirm that your PC has connected to the network and has installed at
least one network protocol.
Insert the included CD into
your CD-ROM drive. The
Autorun.exe program should
be executed automatically.
If not, run Autorun.exe
manually from the CD-ROM
drive’s root directory. The
Installation Manager will be
displayed on the screen
(shown at right). Click
“Client Installation.”

The “Utilities Setup” window
will be displayed. Click
“Next.”

WINDOWS PEER-TO-PEER NETWORK

Click “Next” to install the
utilities in the default folder,
or click “Browse” to specify
the destination folder where
you would like to install the
utilities.

Specify the program folder
where the program icons
will be added; click “Next.”

The system will start to
install the utilities
automatically.

WINDOWS PEER-TO-PEER NETWORK

Now that the installation
procedure is complete, you
are ready to set up the
client’s computer. All
network ports of the print
servers detected on the
network will be added to
your PC automatically. Click
“Continue.”

The Client Installation
procedure is complete.
Click “Finish.”

With this installation, the following tasks have been completed:
• Installation of all utilities and drivers to the client’s PC.
• Addition of all the print server’s network ports of the network to the client’s PC.
You can then perform Windows’ standard Add Printer procedure to add network
printers to your PC. (Refer to Section 3.6.)

3.5 Client Utilities
When Client Installation is
complete, there will be three
tools in the print server’s
Program folder: Network
Ports Quick Setup, Remote
Ports and Uninstall Network
Driver. Uninstall Network
Driver will assist you in
removing all installed client
software; the other two tools
are described below.

WINDOWS PEER-TO-PEER NETWORK

3.5.1 Network Ports Quick Setup
The Network Ports Quick Setup utility offers a very simple method to add or remove
the print server’s printer port from the client’s computer.
During the client’s installation procedure,
the system will automatically search for
all print servers on the network and add
them into the printer ports of the client’s
computer (shown at right).



If you have just installed another new print server in the network, you must run this
program first. This program will search for new print servers and allow you to add
the new network printer port into the client’s computer conveniently. By performing
the standard Add Printer procedure, you can then print directly to the printer through
the newly installed print server.

Be aware that Network Ports Quick Setup utility can only detect and configure all
print servers on the same network: It cannot search and configure print servers on
other subnets across network segments. You must use the Remote Ports utility
described in the next section to manage remote (across network segments) print
servers.
3.5.2 Remote Ports Utility
The Remote Ports utility offers a convenient way fto manage and add a printer
port of the remote print server. From the assistant of this utility, you can print to
other print servers outside the subnet across a network segment. Note, however,
that this function only supports the TCP/IP network protocol.
WINDOWS PEER-TO-PEER NETWORK

1. Run the Remote Ports utility. Click “Add”
to add a remote printer port.

2. Enter the print server’s name and
IP address, select the ports used
and enter the LPR queue name
of each port. Click “OK.”

3. The new remote printer port is displayed.

In order to use the remote printing
function, you need to proceed with
the normal Add Printer procedure
and select your printer port as the
newly added remote printer port.

WINDOWS PEER-TO-PEER NETWORK

3.6 Windows Add Printer Procedure
After adding a network port of the print server to your PC using the Administrator
or Client Installation program, you can follow the procedure described below to
add a printer to Windows. NOTE: The following Add Printer steps are in Windows
Vista and XP: The steps in other operating systems are similar.
3.6.1 Windows Vista
1. Click “Start” and select “Settings\Printers.”
2. Click “Add a Printer.”
3. The Add Printer wizard is
displayed. Select “Add a
local printer.”

4. Choose the suitable printer
port created during the
installation process and
click “Next.”

WINDOWS PEER-TO-PEER NETWORK

5. Select the printer
manufacturer and the
printer model and click
“Next.” If your printer isn’t
on the list, click “Have
Disk…” to install the driver
of the printer. After
installation, the printer
model will be added to the
list.

6. Name your printer and set
the default printer; then
click “Next.”

7. The printer drivers are
being installed.

WINDOWS PEER-TO-PEER NETWORK

8. It is recommended that you
print a test page. Then
click “Finish.”

9. The printer is added to the Printers screen, indicating that you have added the
printer to your computer successfully. Now you can start to print from your
computer to the print server.

WINDOWS PEER-TO-PEER NETWORK

3.6.2 Windows XP
1. On the desktop, go to Start, then Settings: select “Printers and Faxes.”
2. Click “Add a Printer.”
3. The Add Printer Wizard”
screen is displayed. Click
“Next.”

4. Select “Local printer
attached to this computer”
and make sure that
“Automatically detect and
install my Plug and Play
printer” is not selected.
Click “Next.”

5. Choose the suitable “Print
Server Network Port”
created during the
Administrator Installation
or Client Installation
process and click “Next.”

WINDOWS PEER-TO-PEER NETWORK

6. Select a suitable printer
manufacturer and the
printer model and click
“Next.” If your printer isn’t
on the list, click “Have
Disk…” to install the driver
of the printer. After
installation, the printer
model will be added to the
list.

7. Name your printer and set
up the default printer; then
click “Next.”

8. It is recommended that you
print a test page. Then
click “Next.”

WINDOWS PEER-TO-PEER NETWORK

9. You have now successfully
added the printer to the PC.
Information about the
printer is displayed on
screen. Click “Finish.”

4. windows nt/2000/server 2003 network
4.1 System Architecture
In a Windows network environment, in addition to the Peer-to-Peer network
printing architecture described in the previous chapter, the 1-Port USB Wireless
Print Server also offers the server-based printing architecture for Windows NT/2000/
Server 2003. Only one Windows NT/2000/Server 2003 workstation is required to
have the Windows PTPP (Peer-to-Peer Printing) driver installed — it can share the
printing service on the network so other network users can simply connect to the
server and access the shared printer (see below).

4.2 Windows NT/2000/Server 2003 Installation and Setup

The following procedure is for the installation and construct of a peer-to-peer
connection (PTPP) between Windows NT/2000/Server 2003 and the print server.
1. If this is your first time installing the print server, install the administrator software
on Windows NT/2000/Server 2003 first. (Refer to section 3.2 for installation
instructions.)
24

NT/2000/SERVER 2003

If your network has already installed a working print server and your Windows
NT/2000/Server 2003 has not yet installed the PTPP driver, install the client
software. (Refer to section 3.4 and 3.5 for installation instructions.)
2. Add/configure the Peer-to-Peer Printing of the Windows NT/2000/Server 2003
network printer and verify that you can print from Windows NT/2000/Server 2003
to the print server through the installed PTPP driver.
3. Connect the above server’s printer to the network by performing the standard
Windows printer sharing process.

4.3 User Installation
After the server side’s installation
is complete, the client side will be
able to find the server’s shared
printer in Network Neighborhood.
You only need to perform
Window’s standard Add New
Printer procedure, select
“Network Printer” (as shown at
below right), and complete the
configurations afterward to
access the shared printer.

NT/2000/SERVER 2003

5. netware network
5.1 System Architecture
A NetWare printer sharing functionality has been integrated into the 1-Port USB
Wireless Print Server itself, thus allowing one or more printers attached by a print
server to be connected to the network. (The 1-Port USB Wireless Print Server
supports the NetWare print server.) This embedded print server emulates the “queue
management functionality” of a NetWare print server (the PSERVER program
running on the NetWare server). A user first prints a job at a workstation, the job
is routed to a NetWare server, the NetWare server stores the job in a print queue
and then the print server gets the print job from the queue to printers.

Print Queue

Windows 98

Netware Server

Print Server

Windows 2000

Compared with NetWare printing functionality, the advantages of embedding the
NetWare network printing functionality in the 1-Port USB Wireless Print Server
include:
• Installation is easier and quicker.
• Network management is easier.
• Printing performance is enhanced.
• The NetWare file server’s burden is lessened.
• The need for a workstation running the remote printer utility is removed.
• Productivity is improved by locating the printer near the workgroup.
Each print server should log in to a NetWare server before servicing the print jobs,
and each print server will occupy a user account with which it can log in to the
NetWare server.

5.2 NetWare 3.x/4.x/5.x Installation & Setup
Once your print server is connected to your Ethernet network, you can set it up for
use with your networking software.
5.2.1 Installation Using PCONSOLE (Configuring as Print Server Mode)
1. Run the NetWare PCONSOLE program.
2. Change the current file server, if necessary, using the “Change Current File
Server” menu selection.
3. Choose the “Print Queue Information” menu selection.
4. Press the Insert key to add a new print queue.
5. Enter a print queue name, such as “PQ” or “Q1.”
26

NT/2000/SERVER 2003

6. You’ve now successfully created
the print queue that your print
server will serve. Press the
Escape key until the Available
Options main menu is displayed.
7. Select “Print Server Information.”
8. Press the Insert key to add a new
NetWare print server object. The
print server name can be identical
to the PSxxxxxx name printed on
the label of the print server.
9. Press Enter to select the newly
created print server.
10. Select “Print Server
Configuration.”
11. Select “Printer Configuration.”
12. Select “Printer 0” (or “Printer 1,”
“Printer 2”) and press Enter, then
select “P1” (or “P2,” “P3”) in the
“Type” field. NOTE: If your print
server has only one port, you do
not need to configure this field.
13. Press Escape, and answer
“Yes” to the “Save Changes?”
prompt.
14. Select “Queues Serviced by
Printer,” then select “Printer 0”
(or “Printer 1,” “Printer 2”) and
press Enter.
15. Press Insert and add your
newly created print queue to
the list of queues serviced by
the printer. Enter a priority
number for the queue service,
or press Enter to accept the
default.
16. Repeatedly press Escape to
exit the PCONSOLE program.
17. Reset the print server so the changes take effect.
NOTE: If the print server you have has multiple printer connectors, you may create
multiple print queues and printer objects. Your print server should now be ready to
use. You should be able to redirect printing to your print server using a CAPTURE
command such as the one shown in the previous section.

NT/2000/SERVER 2003

6. UNIX System Network
6.1 Introduction
The print server is available for TCP/IP printing by Unix LPD (Line Printer Daemon)
protocol. The LPD protocol, which originated with the Unix release, is based on the
BSD version of Unix and is supported under most versions of Unix.
This chapter explains how to configure the print server for TCP/IP operation, and
how to modify configuration files on your Unix system to allow printing to the print
server. The configuration examples in this manual follow the syntax for BSD-based
Unix systems. Refer to the related system documentation for the correct syntax of
your systems.
The five steps below, which are detailed in the following sections, show how to
configure the print server for LPD printing.
1. Enable the print server’s TCP/IP support.
2. Set up the print server’s IP address.
3. Verify the print server’s IP address.
4. Configure remote LPD printing on the host.
5. Print a test page.

6.2 Enable the Print Server’s TCP/IP Support
The default configuration of the print server is set with TCP/IP support enabled.
You can configure the print server to enable TCP/IP support using the configuration
program.

6.3 Set Up the Print Server’s IP Address
The print server must have a unique IP address in order to be recognized by the
network. You can set up the IP address on the various Unix systems using either:
• DHCP (Dynamic Host Configuration Protocol) or
• BOOTP (Bootstrap Protocol)
6.3.1 DHCP
There are many Unix systems that support the DHCP protocol, and the procedures
to configure the DHCP server database are different. This manual does not
describe the DHCP server configuration on the Unix systems. It is highly
recommended that the DHCP server should be located on the same network as
the print server.
6.3.2 BOOTP
If you have the BOOTP daemon, bootpd, running on your UNIX system that is
accessible by the print server, you can use the BOOTP protocol to set up the IP
address of the print server. It’s recommended that the BOOTP server should be
located on the same subnet as the print server. If you use Network Information
Services (NIS) in your system, you may need to rebuild the NIS map with the
BOOTP services before doing the following BOOTP configuration. To rebuild the
NIS map, refer to your system documentation.
To configure the IP address data for the BOOTP server, you will need to log in the
host of the BOOTP server as the superuser (root). Perform the following steps to
add address entries.
28

UNIX

1. Optionally, assign a name corresponding to the print server’s IP address. You can
add this address to the /etc/hosts file by adding a line such as:
203.66.191.12
pserver
2. Add an entry to the host’s /etc/bootptab file, similar to the following:
hostname:\

:ht=1:\
:ha=print_server_ethernet_address:\
:ip=print_server_ip_address:
Lines should be indented with tabs.
Where the hostname is the device name of a print server, the ht=1 tag specifies
the hardware type is Ethernet; the ha= tag specifies the Ethernet address of a
print server, which is the node ID located on the print server. The ha tag must be
preceded by the ht tag. The ip= tag should correspond to the IP address you want
to assign to the print server.
For example, for a print server with the following configuration:
• Node ID: 0000B4010101 (this implies the Ethernet address is 0000B4010101),
• IP address: 203.66.191.12
the entry for this print server in the /etc/bootptab file should be:
PS010101:\

:ht=1:\
:ha=0000B4010101:\
:ip=203.66.191.12:

6.4 Verify the Print Server’s IP Address
To verify that your print server is responding to the newly assigned IP address
using a PING command:

ping ip-address

6.5 Configure Remote LPD Printing on the Host
The procedure you use to configure your Unix host(s) to allow printing to your
network remote print server varies among different varieties of Unix. The procedure
below can be used for Unix variants that are related to BSD Unix, such as SunOS
or Linux. For other versions of Unix, consult your system documentation, keeping
in mind that:
• The print server should be treated as a BSD-networked print server host.
• The hostname should be the name (or IP address) that you have assigned to the
print server.
• The printer name (or queue name) on the remote host should be p1, p2 or p3 —
the name of the printer port on the print server.
You will need to perform the tasks below, logged in as the superuser (root). To
configure your Unix host for printing,
1. Optionally, assign a name corresponding to the print server’s IP address. You can
add this address to the /etc/hosts file, by adding a line such as:

203.66.191.186
pserver
2. Create a spool directory for the printer in the same directory where spool
directories are normally kept on the machine, such as /var/spool or /var/spool/lpd:

UNIX

mkdir /var/spool/lpd/pserverd
chown daemon /var/spool/lpd/pserverd
chgrp daemon /var/spool/lpd/pserverd
chmod 775 /var/spool/lpd/pserverd
3. Add an entry to the host’s /etc/printcap file, similar to the following:
printer-name:\

:lp=:\

:rm=203.66.191.186:\

:rp=p1:\

:lf=/var/spool/lpd/pserverd.log:\

:sd=/var/spool/lpd/pserverd:\

:mx#0:
Lines should be indented with tabs. More than one printer name can be used, with
variants separated by vertical bars (name1|name2).
The rm= entry should correspond to the IP address you have assigned to the print
server. You can also use a hostname if you’ve assigned one in the /etc/hosts file.
The sd= entry should correspond to the spool directory you created in the previous
step.
The rp= entry should correspond to the port name of the remote printer. The values
should be one of p1, p2 or p3, depending on the printer port.
The print server should now be available for printing from your Unix host.

7. Configuration Utility
7.1 Introduction
This chapter introduces the print server’s system configuration utility in a Windows
environment. This utility is automatically installed during the Windows Administrator
utility installation procedure (refer to sections 3.2 and 3.3).
This utility provides the most complete management and configuration functions
on the print server side. This utility only provides configuration functions for the
print server itself; it does not include configuration functions for the client side or
other file servers or NetWare servers in the network environment.
The Configuration utility provides the following configuration and management
functions (with detailed subsections that follow):
• Search Print Server: Search all available printer servers on the network.
• Print Server Status: Display print server network status.
• General Configuration: General information about the print server.
• TCP/IP Configuration: IP address and DHCP server configuration.
• NetWare Configuration: NetWare printing configuration.
• AppleTalk Configuration: AppleTalk protocol settings.
• Bonjour Configuration: Mac OSX protocol settings.
• SMB: Configure the SMB group name.
• SNMP Configuration: SNMP information configuration.
• Setup Wizard: Guide to all the settings.
• System Configuration: Print server network ability settings, firmware upgrades
and language settings.
• Wireless Configuration: Wireless LAN configuration.
• Report: List the status of all available print servers on the network.

CONFIGURATION UTILITY

7.2 Search for All Available Print Servers

Whenever you run the print server’s configuration utility, click on the Search
icon (left) on the tool bar. The configuration utility will be delayed for several
seconds because the utility is using the system’s available network protocols to
search for all print servers on the network. All available print servers will be listed
under “Server Group” on the left side of the screen. Select the print server you
would like to configure from the list. The system will, at the same time, display the
selected print server’s status on the right side of the screen.

CONFIGURATION UTILITY

7.3 Status of the Print Server

Click on the Status icon (left) on the tool bar to show the status of the current
selected print server on the right side of the screen.
Information displayed about the print server includes MAC ID, model type, firmware
version, status of each printer port, NetWare file server name, NetWare file server
polling interval, NetWare printer queue names, IP address, subnet mask, default
gateway, AppleTalk printer type, AppleTalk zone and print server printing ability.
Refresh the print server’s status by clicking on the Refresh icon (far left).
Restart the print server by clicking on the Reboot icon (near left).

CONFIGURATION UTILITY

7.4 Set Up the Print Server

Click on the Setup icon on the tool bar to show the setup items of the current
selected print server on the right side of the screen. Double-click one of the
icons to set up the selected print server. A screen will display to verify the user
name and password of the print server. The default values are as follows.
• User Name: admin
• Password: 1234

CONFIGURATION UTILITY

7.5 General Configuration
Double-click on the General
icon and the General
configuration screen will
display. You can see basic
print server information on
this screen. You also can
configure the server name,
username and password here.
Server Name is the name
of the print server. You can
use this name to identify the
print server when you are
searching for the print server
using the administration and
client utilities.
User Name / Password is
used to authenticate the administrator using the Web administration tool.

7.6 TCP/IP Configuration
Double-click on the TCP/IP
icon and the TCP/IP
configuration screen will
display. You can configure the
print server to automatically
get an IP address from DHCP
server or manually specify a
static IP. The print server also
has a built-in DHCP server.
You can enable this DHCP
server and let it manage IP
addresses for you.
Click “IP” to enter the IP
settings page. If you need the
print server to automatically
get an IP address from the
DHCP server, select “Auto IP.”
You also can select “Static IP”
to manually assign an IP
address, subnet mask and
gateway for the print server.
Click “DHCP Server” to enter
the DHCP server’s settings
page. You can enable/disable
the DHCP server, or set to
“Auto” and assign a range of
IP addresses here. The DHCP
server is disabled by default.
34

CONFIGURATION UTILITY

If “Auto” is selected, the DHCP server of the print server will be enabled only when
there is no other DHCP server within the network. When “Enable” or “Auto” is
selected, you need to configure starting address, range, subnet mask, gateway
and DNS. The print server will assign a unique IP address for each client.

7.7 NetWare Print Server Configuration
Double-click on the NetWare
icon and the NetWare
configuration screen will
display. This print server
supports NetWare Bindery
Printing. The print server
periodically polls the
NetWare server printer
queues for printing jobs. You
need to assign the NetWare
server name, print server
polling interval and the name
of the queue on the NetWare
server for each printer port.
Polling Time is the polling
interval of the print server waiting for printing jobs on the NetWare server.
Queue Serviced by Printer is the name of the printer queue on the NetWare server.
The printer queue keeps all printing jobs waiting on the NetWare server. You need
to assign a printer queue for each printer port of this print server.
NetWare Server is the name of the NetWare file server that provides printer queues.

7.8 AppleTalk Configuration
Double-click on the AppleTalk
icon and the AppleTalk
configuration screen will
display. AppleTalk is a data
communication protocol often
used by Macs. The print
server can use these
parameters to join the
AppleTalk network and share
the printer to other AppleTalk
workstations. You need to
set up the zone name and
printer type for each printer
port of this print server.
Zone Name: The print
server has to join zones of AppleTalk before it can be shared with other workstations:
Only workstations in the same zone can share the printer. To share the printer with
all workstations in all zones, enter only an asterisk (*) in the “Zone Name” field.
Printer Type is the type of printer attached to each printer port. You can get the
printer type from the manufacturer of the printer.

CONFIGURATION UTILITY

7.9 Bonjour Configuration
Bonjour enables
automatic discovery
of computers,
devices and services
on an IP network.
The service name
will be seen by users
on the IP network,
so choose a unique
(but recognizable!)
name to describe
the device.

7.10 SNMP Configuration
Double-click on the SNMP
icon and the SNMP
configuration window will
display.
Contact: You can enter the
print server administrator’s
contact information here.
This information will be
displayed in the SNMP
management tool.
Location: You can enter the
installed location of the print
server here. This information will be displayed in the SNMP management tool.

7.11 SMB Configuration
SMB Group Name is the
name of SMB group that this
print server belongs to. All
PCs should join the same
group before they can use
this print server using the
SMB protocol.

CONFIGURATION UTILITY

7.12 System Configuration

Double-click on the System icon and the System configuration window will display.
On the System configuration screen, you can enable/disable each printing or
management protocol, assign a name for each printer port of this print server,
upgrade the new firmware for this print server and enable/disable the wireless
function.
Port Name is the name of the printer port. Each printer port has to be assigned a
name. The client utility uses this name to access the printer port.
Upgrade Firmware: You can use this Upgrade Firmware tool to update the newest
firmware of the print server. Click
and select the correct firmware in your PC.
After selecting the firmware file, click “Upgrade” to finish the firmware update
process. If you want to reset the print server to the default factory settings, click
“Load Default.”
Wireless Function: You can select “Enable” or “Disable” to manually enable or
disable the wireless function. If you manually enable the wireless function, the print
server’s wireless LAN will be always enabled and Ethernet will be always disabled.

CONFIGURATION UTILITY

If you manually disable the wireless function, the print server’s wireless LAN will be
always disabled and Ethernet will be always enabled. You also can select “Auto” to
let the print server automatically decide to enable or disable the wireless function.
The print server only can work in ether Ethernet or wireless LAN mode: It cannot
work in both Ethernet and wireless LAN mode at the same time. When the print
server starts up, it will auto-detect if the LAN port is connected to an active network
by an Ethernet cable. If the print server is connected to an active network through
an Ethernet cable when starting up, the print server will run in Ethernet mode. If
the print server is not connected to an active network by Ethernet cable when
starting up, the print server will run in wireless LAN mode. The print server default
is in “Auto” mode.
Domain Country: The wireless channels vary from country to country. Generally,
the channels are from 1 to 11 in the U.S. and from 1 to 13 in Europe. The operating
channel will be set to the print server before importing. If you are in a different
locale, make sure that you have set the available channels according to your
location.

7.13 Wireless Configuration
If you want to use the print server through a wireless LAN, set up the print server
through Ethernet first and make sure your wireless LAN setting is correct. After
setting the wireless LAN, unplug the Ethernet cable and restart the print server;
then you can start to use the print server through the wireless LAN. NOTE: If the
wireless configuration doesn’t work, plug the Ethernet cable in again, restart the
print server and configure the print server through Ethernet until the wireless LAN
settings are correct.
The default settings of the print server wireless function are as follows.
• Mode: Infrastructure
• SSID: Default
• Channel: 11

CONFIGURATION UTILITY

Double-click on the Wireless icon and the wireless configuration window will display.
If you use access points to create a wireless network, Infrastructure mode is used.
After selecting the operation modes of the wireless function, click “Next” to display
detailed configuration information.
Infrastructure Mode

In Infrastructure mode, you need to let the print server associate with an access
point. The print server can scan for an available access point automatically or you
can manually assign the SSID of the access point you want to use.
If you elect to let the print
server scan for an available
access point, the screen at
right will display. The list is
of the scanned available
access points. Select an
access point on the list and
click “Next.” If you can’t find
the access point that you
want to use, click “Scan” to
let the print server scan
again.

The following procedures are necessary to continue with the configuration of the
Infrastructure mode settings.

CONFIGURATION UTILITY

This print server supports WEP, WPA-PSK and WPA2-PSK security modes. To
use WEP encryption to protect your wireless network, select “WEP(ASCII)” or
“WEP(HEX).” To use WPA-PSK, select “WPA-PSK.” To use WPA2-PSK, select
“WPA2-PSK.” The wireless security setting should be the same on other wireless
devices in the same network.
WEP Security Mode

Select “64 bit” or “128 bit” length and “Hexadecimal” or “ASCII” format for the
encryption key. NOTE: A longer key length can provide stronger security, but at
the expense of communication performance.
40

CONFIGURATION UTILITY

Enter four key values using the guidelines below and select one key as the default
key.
PassPhrase: A passphrase simplifies the WEP encryption process by automatically
generating the WEP encryption keys for the print server. This setting is only valid
when the security mode is “WEP(HEX).”
Key 1 — Key 4: If the key length is 64-bit, enter 10-digit Hex values or 5-digit
ASCII values as the encryption keys. For example: “0123456aef” or “Guest.” If the
key length is 128-bit, enter 26-digit Hex values or 13-digit ASCII values as the
encryption keys. For example: “01234567890123456789abcdef” or “administrator.”
WPA-PSK Mode

“WPA-PSK” requires users to select the advanced encryption methods — TKIP or
AES — and enter a set of shared keys.
CONFIGURATION UTILITY

TKIP: The Temporal Key Integrity Protocol (TKIP) changes the temporal key every
10,000 packets. This ensures much greater security than standard WEP security.
AES: AES has been developed to ensure the highest degree of security and
authenticity for digital information. It’s the most advanced solution defined by IEEE
802.11i for security in the wireless network.
Pre-shared Key Format: Select “Passphrase” or “Hex” key format. If “Passphrase”
is selected, enter 8 to 63 digits of ASCII format as the key for authentication within
the network. If “Hex” is selected, enter 64 digits of Hex code (“0-9” and “A-F”).
WPA2-PSK Mode

“WPA2-PSK” requires that you select the advanced encryption methods — TKIP
or AES — and enter a set of shared keys.
AES: AES has been developed to ensure the highest degree of security and
authenticity for digital information. It’s the most advanced solution defined by IEEE
802.11i for security in the wireless network.
Key: Enter 8 to 63 digits of ASCII format as the key for authentication within the network.
When you finish configuring the wireless security, click “Next” to continue.
You can elect to let the print
server automatically obtain
IP settings with DHCP Client
or to manually assign the IP
settings.
If you manually assign the
IP settings, you need to
enter the IP address, subnet
mask and default gateway
address.
When you finish configuring
the IP settings, click “Next”
to confirm the IP address
configuration.

CONFIGURATION UTILITY

Click “Save” to save the
wireless configuration.

7.14 Wizard

Click on the Wizard icon (left) on the tool bar to display the setup wizard item
of the current selected print server on the right side of the screen. Doubleclick on the Print Server Setup Wizard and the setup wizard will guide you through
the entire setup process.

CONFIGURATION UTILITY

1. Set up the name
of this print
server and the
port name for the
print server, and
choose to enable
or disable the
wireless function.

2. Select/enable the
required printing
protocol (refer to section
7.12 for details).

3. Set up the IP address of
this print server and the
DHCP server (refer to
section 7.6 for details).

CONFIGURATION UTILITY

4. Set up the NetWare
printing (refer to section
7.7 for details).

5. Select the Wireless
Adapter mode and
complete the wireless
LAN settings. NOTE:
The other procedures
are the same as the
“Wireless” settings on
the Setup screen (refer
to section 7.13 for
details).

6. Click “Save” to
finish the
procedure.

CONFIGURATION UTILITY

7.15 Report

Click on the Report icon (left) on the tool bar to display the Report screen.
The report lists basic information about all available print servers on the
network, including device name, MAC ID, model type, firmware version and the
status of the print server.

8. web management
8.1 Introduction
The 1-Port USB Wireless Print Server can be configured and managed on the Web.
Through a local area network, or even the Internet, an administrator can easily
configure and manage the print server’s various main functions in browsers. Simply
enter the print server’s IP address into your browser’s address field to manage a
print server using the print server’s built-in Web server.
The default IP address, username and password settings of the print server are as
follows.
• IP Address: 192.168.2.2
• User Name: Admin
• Password: 1234

8.2 Login
You can use any Web browser to review
the status or configure the settings of the
print server. After entering the IP address
of the print server, a login page displays
(right). Make the correct entries in the
“User Name” and “Password” fields, then
proceed to the Web Management pages.

WEB MANAGEMENT

8.3 Device Status
8.3.1 System
System Information includes the device name, print server name, model type,
system up time, firmware version, MAC address and the status of the protocols
enabled.

8.3.2 Printer
This screen lists information about the printer connected to the printer port.

WEB MANAGEMENT

8.3.3 TCP/IP
This screen lists all TCP/IP settings of the print server, including the IP address,
subnet mask and gateway. It also lists DHCP server settings.

8.3.4 SMB
This screen lists the SMB group settings of the print server.

WEB MANAGEMENT

8.3.5 SNMP
This screen lists the SNMP settings of the print server, including the SNMP system
contact and SNMP system location.

SNMP System Community: To enter the name of the system group. The default
name is “public.”
SNMP System Manager IP: The IP address for the trap alarm.
SNMP Trap: There are two levels to choose from: v1 and v2.
8.3.6 NetWare
This screen lists NetWare settings, including polling time, Bindery mode settings,
name of the file server and port attached queue.

WEB MANAGEMENT

8.3.7 AppleTalk
This screen lists AppleTalk settings, including the AppleTalk zone name and the type
of printers connected to all print ports.

8.3.8 Bonjour
This screen lists Bonjour settings, including the port service name of each port.

WEB MANAGEMENT

8.4 Setup Wizard
8.4.1 System
You can change the print server name and port name of the print server from here.

Print Server Name is the name of the print server. You can use this name to
identify the print server when you are searching for the print server by the
administrator and client utilities.
Port Name is the name of the printer port. Each printer port has to be assigned a
name to be used to access the printer port.
8.4.1.1 Admin Password
This screen allows you to change the password of the print server.

WEB MANAGEMENT

Name is the administrator name of the print server. If you change the name, you
need to log in to the print server from the administrator utility or Web management
with the new name. The default user name is “admin.”
Password: Enter the password you want to change for the print server. The
password can be up to an 8-digit alphanumeric format. The default password is
“1234.”
Re-type Password: Enter the password you want to change for the print server
again.
8.4.1.2 Advanced Settings
This screen allows you to enable/disable the printing protocol.

To enable the function, select “Enable”; to disable the function, select “Disable.”
8.4.2 Wireless
If you want to use the print server through a wireless LAN, set up the print server
through the Ethernet first and make sure your wireless LAN setting is correct. After
setting the wireless LAN, unplug the Ethernet cable and restart the print server.
You can then start to use the print server through the wireless LAN. If the wireless
configuration doesn’t work, plug the Ethernet cable in again, restart the print server
and configure the print server through the Ethernet until the wireless LAN settings
are correct.
You can set parameters that are used for the wireless stations — including Function
and ESSID — to connect to this print server. You can manually set the parameters
of a wireless LAN on this screen or use the Site Survey function to automatically
search for an available access point and associate with it.
Mode is the operation mode of wireless station. If you’re using an access point in
the wireless LAN infrastructure, the wireless mode is Infrastructure.
ESSID is the unique name identifying a wireless LAN. The ID prevents the
unintentional merging of two co-located WLANs. Make sure that the ESSID of all

WEB MANAGEMENT

stations and access points in the same WLAN network is the same.
Channel Number is the channel number of your wireless LAN. The channel
number is set to “11.”
8.4.2.1 Site Survey
This screen allows you to search for available access points in your location.

On the list is information about all available access points or wireless stations,
including SSID, BSSID, channel, type, encryption and signal strength. You can
select one wireless device on the list for this print server to associate with.

WEB MANAGEMENT

8.4.2.2 Encryption
This print server supports WEP, WPA-PSK and WPA2-PSK security modes. To
use WEP encryption to protect your wireless network, select “WEP.” To use WPAPSK, select “WPA-PSK.” To use WPA2-PSK, select ‘’WPA2-PSK.’’ The wireless
security setting should be the same for other wireless devices in the same network.
WEP Security Mode

Key Length: Choose “64-bit” to use WEP with 64-bit key length encryption; choose
“128-bit” to use WEP with 128-bit key length encryption. NOTE: A longer key
length can provide stronger security, but at the expense of throughput.
Key Format: Use ASCII characters (alphanumeric format) or hexadecimal digits
(in the “A-F,” “a-f” and “0-9” ranges) for the WEP key.
PassPhrase: A passphrase simplifies the WEP encryption process by automatically
generating the WEP encryption keys for the print server.
Default Key: Select one of the four keys to encrypt your data. Only the key you
select in the “Default key” drop-down menu will take effect.
Key 1 – Key 4: The WEP keys are used to encrypt data transmitted within the
wireless network. If the key length is 64-bit, enter 10-digit Hex values or 5-digit
ASCII values as the encryption keys. For example: “0123456aef” or “Guest.” If the
key length is 128-bit, enter 26-digit Hex values or 13-digit ASCII values as the
encryption keys. For example: “01234567890123456789abcdef” or “administrator.”

WEB MANAGEMENT

WPA-PSK Security Mode

“WPA-PSK” requires that you select one of the advanced encryption methods —
TKIP or AES — and enter a set of shared keys.
TKIP: The Temporal Key Integrity Protocol (TKIP) changes the temporal key every
10,000 packets. This ensures much greater security than standard WEP.
AES: AES has been developed to ensure the highest degree of security and
authenticity for digital information. It’s the most advanced solution defined by IEEE
802.11i for security in the wireless network.
Pre-shared Key Format: Select “Passphrase” or “Hex” key format. If “Passphrase”
is selected, enter 8 to 63 digits of ASCII format as the key for the authentication
within the network. If “Hex” is selected, enter 64 digits of Hex code (“0-9” and “A-F”).
Pre-Shared Key: Enter your encryption code in this field.

WEB MANAGEMENT

WPA2-PSK Security Mode

“WPA2-PSK” requires that you enter shared keys with AES algorithms only.
AES: AES has been developed to ensure the highest degree of security and
authenticity for digital information. It’s the most advanced solution defined by IEEE
802.11i for security in the wireless network.
Pre-shared Key Format: Select “Passphrase” or “Hex” key format. If “Passphrase”
is selected, enter 8 to 63 digits of ASCII format as the key for the authentication
within the network. If “Hex” is selected, enter 64 digits of Hex code, (“0-9” and “A-F”).
When you finish configuring the wireless security, click “Save & Next” to confirm
the configuration.
8.4.3 TCP/IP

WEB MANAGEMENT

You can configure the print server to automatically get an IP address from the
DHCP server, or to manually specify a static IP address. The print server also has
a built-in DHCP server. You can enable this DHCP server and let it manage the IP
process for you.
If you need the print server to automatically get an IP address from the DHCP
server, select “Enable Obtain TCP/IP Settings Automatically (Use DHCP/ BOOTP).”
You also can select “Disable Use the following TCP/IP Settings” to manually assign
an IP address, subnet mask and gateway for the print server.
You can enable/disable or set to “Auto” for the print server’s DHCP server. The
DHCP server is disabled by default. If the DHCP server is enabled or set to “Auto,”
you need to assign a range of IP addresses here. Fill in the “Start IP,” “Range,”
“DNS,” “Subnet Mask” and “Gateway” fields, and the print server will assign a
unique IP for each client. NOTE: When “Auto” is selected, the DHCP server of the
print server will be enabled only when there is no other DHCP server within the
network.
8.4.4 SMB

You can enable/disable the SMB protocol from here. If SMB is enabled, enter the
SMB group name to specify the SMB group that this print server belongs to. All
PCs should join the same group before they can use this print server using the
SMB protocol. Furthermore, you can enable the “Pass Job When Error Occurred’’
function and enter the time length (1-60 seconds) in the “Waiting time to pass job’’
field.

WEB MANAGEMENT

8.4.5 SNMP
The print server supports SNMP configuration. If it’s enabled, set up the following
parameters.

SNMP System Contact: You can enter the print server administrator’s contact
information here. This information will be displayed in the SNMP management tool.
SNMP System Location: You can enter the installed location of the print server
here. This information will be displayed in the SNMP management tool.
SNMP System Community: To enter the name of the system group. The default
name is “public.”
SNMP System Manager IP: The IP address for the trap alarm.
SNMP Trap: There are two levels to choose from: v1 and v2.
8.4.6 NetWare
This print server supports the NetWare Bindery Printing method. The print server

WEB MANAGEMENT

periodically polls the NetWare server printer queues for printing jobs. You have
to assign the NetWare server name, print server polling interval and the name of
queue on the NetWare server for each printer port.
Polling Time is the polling interval of the print server for waiting printing jobs on
the NetWare server.
Name of the File Server is the name of the NetWare file server that provides
printer queues.
Attached Queue is the name of the printer queue on the NetWare server. The
printer queue keeps all printing jobs waiting on the NetWare server. You need to
assign a printer queue for each printer port of this print server.
8.4.7 AppleTalk
AppleTalk is a data communication protocol often used by Macs. The print server
can use these parameters to join the AppleTalk network and share the printer to
other AppleTalk workstations. You need to either enable or disable AppleTalk and
set up the zone name and printer type for each printer port of this print server.

AppleTalk Enable: Enable or disable AppleTalk.
AppleTalk Zone Name: The print server has to join zones of AppleTalk before it
can be shared with other workstations. Only workstations in the same zone can
share the printer. If you want to share the printer with all workstations in all zones,
enter only and asterisk (*) in the “Zone Name” field.
Printer Type is the type of printer attached to each printer port. You can get the
printer type from the manufacturer of the printer.

WEB MANAGEMENT

8.4.8 Bonjour
Bonjour enables automatic discovery of computers, devices and services on an IP
network. The service name will be seen by users on the IP network, so choose a
unique (but recognizable!) name to describe the device.

8.4.9 Save Settings
Click “Save Settings” to save the settings and restart the system.

WEB MANAGEMENT

8.5 System Tools
8.5.1 Load Default
You can use this screen to restore the factory default settings. All of your previous
setup will be cleared.

8.5.2 Upgrade Firmware from Browser
You can upgrade new firmware for the print server on this screen.

Browse

Click “Browse” to select the new firmware in your storage, then click “OK.” The
firmware will be updated in several minutes. NOTE: Once you’ve started upgrading
the firmware, you need to follow all the upgrading steps or the print server can’t return
to its normal configuration.

WEB MANAGEMENT

8.5.3 Backup Settings
To back up the print server settings to a “config.bin” file, select “Backup settings
from Print Server.”

8.5.4 Restore System
To apply the settings from the backup file, select “Restore settings from file” and
specify a file to restore.

Browse

WEB MANAGEMENT

8.5.5 Language
To apply the language you want to use, select “TW” for Chinese or “EN” for
English; then click “OK.”

9. telnet management
9.1 Introduction
The 1-Port USB Wireless Print Server an be configured and managed by Telnet.
Through a local area network, or even over the Internet, an administrator can
easily configure and manage the print server’s various main functions using a
Telnet client tool.

9.2 Login
Execute the Telnet client tool and connect to the print server’s IP address:
telnet 192.168.2.2
You’ll then be prompted to enter the username and password.

After you enter the correct username and password, an “admin#” prompt will be
displayed, indicating that you can start to manage the print server by command.

TELNET MANAGEMENT

9.3 Get Setting Values – The ‘get’ Command
The “get” command (formatted as: get argument [value] — see the table below) is
used to get the setting values of the print server. For example, to get the IP address
of the print server, type the “get ip” command after the “admin#” prompt. The IP
value “IP_ADDR=’192.168.2.2’” will be displayed:
admin# get ip  IP_ADDR=’192.168.2.2’
If you enter “get” only, the system will list all available arguments for the “get”
command, as presented in the following table.
Argument
Description
Example

psname
password
username
wlfunc

wlmode
ESSID
channel
wep
defkey

key641
key642
key643
key644
key1281
key1282
key1283
key1284
ip
gateway

Print server name

admin# get psname
PORT1_PS=’PS254896’
Login password
admin# get password
USER_PASSWORD=’1234’
Login username
admin# get username
USER_NAME=’admin’
Wireless LAN function is enabled admin# get wlfunc
or disabled
WIRELESS_FUNCTION=2
0: disabled
1: enabled
2: auto
Wireless LAN mode is
admin# get wlmode
Infrastructure
AP_MODE=1
0: Infrastructure
ESSID of the wireless LAN
admin# get ESSID
SSID=’default’
Channel number used by wireless admin# get channel
LAN
CHANNEL=11
The mode of WEP
admin# get wep
0: disable
WEP=0
1: 64 bit WEP enabled
2: 128 bit WEP enabled
Default WEP key number
admin# get defkey
0: key 1
WEP_DEFAULT_KEY=0
1: key 2
2: key 3
3: key 4
64 bit WEP key 1
admin# get key641
WEP64_KEY1=0123456789
64 bit WEP key 2
admin# get key641
WEP64_KEY2=0123456789
64 bit WEP key 3
admin# get key641
WEP64_KEY3=0123456789
64 bit WEP key 4
admin# get key641
WEP64_KEY4=0123456789
128 bit WEP key 1
admin# get key1281
WEP128_KEY1=0123456789
abcdef0123456789a
128 bit WEP key 2
admin# get key1282
WEP128_KEY2=0123456789
abcdef0123456789a
128 bit WEP key 3
admin# get key1283
WEP128_KEY3=0123456789
abcdef0123456789a
128 bit WEP key 4
admin# get key1284
WEP128_KEY4=0123456789
abcdef0123456789a
IP of the print server
admin# get ip
AP_ADDR=’192.168.2.2’
Default gateway of the print server admin# get gateway
DEFAULT_
GATEWAY=’192.168.2.254’

TELNET MANAGEMENT

submask
polling

Subnet mask of the print server

aq1
applezone
printertype1

admin# get aq1
PORT1_QNAME=’PQ1’
admin# get applezone
PORT1_APPLEAONE=’*’
admin# get printertype1
PORT1_
PRINTTYPE=’LaserWriter’
The name of the SMB group
admin# get SMBDG
name that this print server joins to SMBD_NAME=’default’
The administrator contact
admin# get SNMPC
information of this print server for SNMP_CONTACT=’sbdjohn@
SNMP
hotmail.com’
The installed location of this print admin# get SNMPL
server for SNMP
SNMP_LOCATION=’Room 301’
The port name of this print server admin# get port1
PORT1_LPTNAME=’���
p��
1’
The DHCP server is enabled or
admin# get DHCPS
disabled
DHCPD=0
0: disable
1: enable
Get dynamic IP by DHCP is
admin# get DHCP
enabled or disabled
DYNAMIC_IP=0
0: disable
1: enable
AppleTalk printing is enabled or
admin# get appletalk
disabled
APPLE_ENABLE=0
0: disable
1: enable
SMB printing is enabled or
admin# get SMBD
disabled
SMBD_ENABLE=1
0: disable
1: enable
SNMP management protocol is
admin# get SNMP
enabled or disabled
SNMP_ENABLE=1
0: disable
1: enable
NetWare Bindery printing is
admin# get IPX
enabled or disabled
IPX_ENABLE=1
0: disable
1: enable
LPR printing is enabled or
admin# get LPD
disabled
LPD_ENABLE=1
0: disable
1: enable
IPP printing is enabled or disabled admin# get IPP
0: disable
IPP_ENABLE=1
1: enable
RAW printing is enabled or
admin# get RAW
disabled
RAW_ENABLE=1
0: disable
1: enable

SMBDG
SNMPC
SNMPL
port1
DHCPS
DHCP
appletalk
SMBD
SNMP
IPX
LPD
IPP
RAW

admin# get submask
SUBNET_MASK=’255.255.255.0’
admin# get polling
PORT1_POLLTIME=3

TELNET MANAGEMENT

9.4 Modify Setting Values – The ‘set’ Command
The “set” command (formatted as: set argument [name value] — see the table
below) is used to modify the print server setting values, which will be written into
the system configuration. For example, if you want to set the IP address of the print
server to 192.168.2.2, type “set ip 192.168.2.2” and the IP address of the print
server will be changed. After the setting is finished, reboot the print server (admin#
reboot).
If you enter “set” only, the system will list all available arguments for the “get”
command, as presented in the following table.
Argument

psname
password
username
wlfunc
wlmode
ESSID
channel
wep
defkey

key641
key642
key643
key644
key1281
key1282
key1283
key1284
ip
gateway
submask
66

Description

Print server name
Login password
Login username
Enable or disable the wireless
LAN function.
The value should be “disabled,”
“enabled” or “auto”
Wireless LAN mode is
Infrastructure�.
The value should be “inf”
ESSID of the wireless LAN
Channel number used by wireless
LAN.
The mode of WEP.
The value should be “disable,”
“wep64” or “wep128”
Default WEP key number.
The value should be 0–3.
0: key 1
1: key 2
2: key 3
3: key 4
64 bit WEP key 1.
The value should be 10-digit Hex
value
64 bit WEP key 2.
The value should be 10-digit Hex
value
64 bit WEP key 3.
The value should be 10-digit Hex
value
64 bit WEP key 4.
The value should be 10-digit Hex
value
128 bit WEP key 1.
The value should be 26-digit Hex
value
128 bit WEP key 2.
The value should be 26 digit Hex
value
128 bit WEP key 3.
The value should be 26-digit Hex
value
128 bit WEP key 4.
The value should be 26-digit Hex
value
IP of the print server
Default gateway of the print server
Subnet mask of the print server

TELNET MANAGEMENT

Example

set psname PS001
set password 1234
set username admin
set wlfunc auto

set wlmode ��������������
infrastructure
set ESSID default
set channel 11
set wep disable
set defkey 0

set key641 0123456789
set key641 0123456789
set key641 0123456789
set key641 0123456789
set key1281 0123456789ab
cdef0123456789a
set key1282 0123456789ab
cdef0123456789a
set key1283 0123456789ab
cdef0123456789a
set key1284 0123456789ab
cdef0123456789a
set ip 192.168.2.2
set gateway 192.168.2.254
set submask 255.255.255.0

polling
aq1
applezone
printertype1
SMBDG
SNMPC
SNMPL
port1
DHCPS
DHCP
appletalk
SMBD
SNMP
IPX
LPD
IPP

Polling interval (in second) of the
print server for waiting printing
jobs on the NetWare server
Name of the printer queue on the
NetWare server
The name of AppleTalk zone that
this print server joins to
The type of the printer attached to
this print server
The name of the SMB group
name that this print server joins to
The administrator contact
information of this print server for
SNMP
The installed location of this print
server for SNMP
The port name of this print server
Enable or disable the DHCP
server.
The value should be “disabled” or
“enabled.”
Enable or disable to get dynamic
IP by DHCP.
The value should be “disabled” or
“enabled.”
Enable or disable AppleTalk
printing
The value should be “disabled” or
“enabled.”
Enable or disable SMB printing
The value should be “disabled” or
“enabled.”
Enable or disable SNMP
management protocol
The value should be “disabled” or
“enabled.”
Enable or disable NetWare
Bindery printing
The value should be “disabled” or
“enabled.”
Enable or disable LPR printing
The value should be “disabled” or
“enabled.”
Enable or disable IPP printing
The value should be “disabled” or
“enabled.”

set polling 3
set aq1 PQ1
set applezone *
set printertype1 �����������
L����������
aserWriter
set SMBDG default
set SNMPC sbdjohn@hotmail.
com
set SNMPL Room 301
set port1 p�
��
1
set DHCPS disable

set DHCP disable

set appletalk disable

set SMBD enable
set SNMP enable

set IPX enable

set LPD enable
set IPP enable

9.5 Other Commands
ipconfig — quickly gets the IP settings (IP address, subnet mask, default gateway)
of the print server:

admin# ipconfig 
IP_ADDR=192.168.2.2

SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=192.168.2.254
reboot — restarts the print server
exit — leaves the print server Telnet management program
help — lists all Telnet management commands of the print server

TELNET MANAGEMENT

10. IPP Printing
10.1 Introduction
IPP (Internet Printing Protocol) printing provides a convenient way of remote
printing by TCP/IP. The print server supports IPP printing by default: No special
settings are necessary. Any PC that can support IPP printing can directly use the
print server through the IP address (thus, even sharing print-server access over
the Internet).

10.2 System Setup
10.2.1 Print Server Side
No settings are necessary on the print server side: Just make sure the print server
has correct IP settings. If you want to share with Internet users, assign a real IP
address to the print server and make sure that no gateway, router or firewall blocks
the IPP protocol (if you have these gateway devices installed in your network).
10.2.2 Client Side
All that’s needed is to perform Window’s standard Add New Printer procedure.
1. On the desktop, go to Start, then Settings. Select “Printers and Faxes.”
2. Click “Add a Printer” to
display the Add Printer
Wizard screen.
3. Click “Next” to display the
Local or Network Printer
screen.

4. Select “A network printer,
or a printer attached to
another computer”; then
click “Next” to display to
the Specify a Printer
screen.

IPP PRINTING

5. Select “Connect
to a printer on the
Internet or on a
home or office
network” and enter
the URL of the
print server (the
format is “http://IP:
631/Port Name”).
The IP address
should be that of
the print server.
“631” is the standard
IPP port number.
The port name (the
last segment of the
URL) is the port
name of the print
server that your
printer is connected to. The default port name is “p1.” One example of the URL
(as shown) is http://192.168.3.66:631/p1. After entering the URL of the print
server, click “Next.”
6. Select a suitable printer
manufacturer and the
printer model, then click
“Next.” If your printer is not
in the list, click “Have
Disk…” to install the driver
of the printer. After
installation, the printer
model will be added to the
list.

7. On the Default Printer
screen, choose whether
you want to use the device
as a default printer or not.
Click “Next.”

IPP PRINTING

8. The printer information
displays, indicating that
the process is complete.
Click “Finish.”

11. Windows XP SP2 Setup
In Windows XP SP2, the service pack’s firewall is designed to block unrecognized
communications. This print server, however, allows the communications data to
pass through the firewall. If you can’t find a print server listed in the “Available
Ports” window in Network Ports Quick Setup, follow the steps below.
1. On the desktop, go to Start, then Settings. Select “Network Connections.”
2. Right-click on Local Area Connection and select “Properties.”

XP SP2

3. Click on the Advanced tab
and click “Settings….”

4. Click on the Exceptions tab
and click “Add Program….”

XP SP2

5. Click “Browse” to add a
new program.

6. Open the “NPUtil” file
from “C:\Program Files\
PrintServer Utilities”
(where C:\ is the system
drive).

XP SP2

7. If “Network Ports Quick
Setup” is displayed in the
list, click “OK.”

8. The procedure is complete:
The Windows XP SP2 will
allow the incoming network
connections activated by
the program. Click “OK.”

XP SP2

12. specifications
General
• CPU: MIPS CPU (240 MHz)
• Flash: 2 MB NOR Flash
• RAM: 16 MB SDRAM
• Printer port: USB 2.0 type A x 1
• LAN port: 10/100M UTP port x 1 (Auto-MDI/MDI-X)
• Antenna: external 2 dBi dipole antenna
• Output power: 16 - 18 dBm
• Power: 5 V DC, 1 A power adapter
• Dimensions: 20 (H) x 58 (W) x 82 (D) mm
• Temperature: 0 – 55˚C
• Humidity: 10 – 90% (non-condensing)
• Certification: FCC, CE class B
Package Contents
• Wireless Print Server
• Detachable antenna
• Power adapter
• Utility CD (software & user manual)
• Quick start guide

SPECIFICATIONS

INTELLINET NETWORK SOLUTIONS™ offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit

www.intellinet-network.com.

Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1.1-111
Instance ID                     : uuid:b9969845-30cf-11dd-9fba-000a95bb094a
Document ID                     : adobe:docid:indd:5ff0db3c-24b7-11dd-93b5-9b4852dfe7a0
Rendition Class                 : proof:pdf
Derived From Instance ID        : 3a7a018a-24ad-11dd-93b5-9b4852dfe7a0
Derived From Document ID        : adobe:docid:indd:3a7a0187-24ad-11dd-93b5-9b4852dfe7a0
Manifest Link Form              : ReferenceStream
Manifest Placed X Resolution    : 72.00
Manifest Placed Y Resolution    : 72.00
Manifest Placed Resolution Unit : Inches
Manifest Reference Document ID  : adobe:docid:photoshop:f0874c39-cae2-11da-a1b4-f9925afeb75f
Create Date                     : 2008:06:02 14:13:36-04:00
Modify Date                     : 2008:06:02 14:14:22-04:00
Metadata Date                   : 2008:06:02 14:14:22-04:00
Creator Tool                    : Adobe InDesign CS2 (4.0)
Format                          : application/pdf
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Page Count                      : 76
Creator                         : Adobe InDesign CS2 (4.0)

EXIF Metadata provided by EXIF.tools

509060 Manual

Navigation menu

Versions of this User Manual:

Views

Navigation