ZSS QCPOO
2014-10-22
: Pdf 520975-Attachment 520975-Attachment Batch9 unilog
Open the PDF directly: View PDF .
Page Count: 4
Download | ![]() |
Open PDF In Browser | View PDF |
CP SERIES ELECTRIC RADIANT CEILING PANELS 470 Beauty Spot Rd. E, Bennettsville, SC 29512 END FRAME SCREWS SIDE FRAME END FRAME SIDE FRAME MOUNTING HOLES File # E21609 CORNER HEATING PANEL Recess Mounting Kit Surface Mounting Kit CEILING PANELS TAG CATALOG NUMBER QTY. TAG SIZE VOLTS CAT. NO. QTY. WATTS CUSTOM FEATURES DESCRIPTION ACCESSORIES AND CONTROLS DATE: PROJECT: ARCHITECT: ENGINEER: CONTRACTOR: SUBMITTED BY: ZSS-QCPOO (03-02) Printed in U.S.A. CP SERIES - ELECTRIC RADIANT CEILING PANELS SUBMITTAL SHEET STANDARD FEATURES CUTAWAY DRAWING OF A HEATING PANEL 24 GAUGE STEEL BACK OF UNIT MIN. 1 INCH, 1 POUND DENSITY HIGH TEMPERATURE FIBERGLASS INSULATION ENCAPSULATED CASSETTE 22 GAUGE STEEL FRONT OF UNIT CRYSTALLINE SURFACE T-BAR SYSTEM CEILING TILE RADIANT HEATING PANEL UNIVERSAL MOUNTING CLIP CEILING TILE T-BAR GRID CAT. NO. CP251 CP258 CP252 CP257 CP253 CP311 CP318 CP312 CP317 CP313 CP371 CP378 CP372 CP377 CP373 CP501 CP508 CP502 CP507 CP503 CP621 CP628 CP622 CP627 CP623 CP751 CP758 CP752 CP757 CP753 VOLTS 120 208 240 277 347 120 208 240 277 347 120 208 240 277 347 120 208 240 277 347 120 208 240 277 347 120 208 240 277 347 WATTS WIRING - For connection to the main power supply, the heater is completely prewired including green ground wire, with the lead wires housed in a 48-inch length of flexible metal conduit and connector for J-Box mounting. STANDARD FINISH - Standard mounting kits finished white to blend with standard panel birch white finish. SCREWS END FRAME MOUNTING HOLES SIDE FRAME FRAME CONSTRUCTION FOR SURFACE MOUNT PANELS EXTRUDED ALUMINUM FRAME RADIANT HEATER METAL: Extruded Aluminum. Decorative Frame: .062" thick, 3" deep. DIM. (IN.) WOOD: Heaters can be framed in wood Consult your factory representative for specifics. 250 310 SIDE FRAME 24 x 24 x 1 END FRAME CORNER 375 500 625 24 x 48 x 1 750 CRYSTALLINE SURFACE - The panel’s unique crystalline surface greatly enhances the radiant characteristics of the heating panel. Radiant output is in the 8-10 micron wavelength. This is ideal for comfort. Human skin will absorb 99% of the radiant energy in these wavelengths. Humans themselves radiate heat predominately in that micron range. Without the panel’s crystalline surface a panel will be less radiant, operate at higher temperature and produce energy at shorter wavelengths. ELEMENT - Encapsulated cassette heating element assures uniform temperatures and long life. 2 METAL: Back - 24 Gauge Galvanized or Aluminized Steel. Front - 22 Gauge Galvanized or Aluminized Steel. Sides - Overlapping Front and Back. WIRE: Internal - 200°C, 14 Gauge, Teflon insulated. External - Pig Tails with 48" of 1/2" flexible conduit and connector for J-Box. ELEMENT: The encapsulated cassette element delivers a uniform temperature distribution over entire panel surface. INSULATION: Minimum 1 inch, 1 pound density, high temperature fiberglass. SURFACE: All ceiling and wall mounted panels are coated with unique crystalline surface. Birch white finish. UNIVERSAL HANGING CLIPS - All radiant ceiling panels are supplied with COMBINATION EARTHQUAKE/T-BAR GRIP CLIPS as a standard feature. These clips have holes for support chains or can be folded over the T-BAR to reduce lateral movement. FRAME CONSTRUCTION FOR RECESSED PANELS CEILING JOIST RADIANT HEATER CERTIFICATION AND SAFETY FIRE RATING - Heating panels do not have a fire rating, but construction is of fire retardant materials. Panels normally are treated like light fixtures. If necessary, acoustical tile can be placed on top of the panels. HAZARDOUS AREAS - Heating panels do not have a hazardous rating. ACCESSORIES PRODUCT QSF2424 QSF2448 QRF2424 QRF2448 DESCRIPTION Surface Mounting Frame for 24” x 24” Panels Surface Mounting Frame for 24” x 48” Panels Recess Mounting Frame for 24” x 24” Panels Recess Mounting Frame for 24” x 48” Panels METAL: Extruded aluminum inverted "T". "T" .125 thick by 1.432 wide by 1.875" high. FRAME * Measuring for Custom Ceiling Panels: • Panels are built to fit inside the dimensions given. • Measurements must be from “T” Bar 0Center Line to “T” Bar Center Line • Do Not Measure Opening CUSTOM FEATURES 1. 7. PANEL FRONTS FOR A CONTINUOUS CEILING LINE CUSTOM SIZE PANELS While a wide variety of panel sizes are listed as standard, the factory produces thousands of panels each year of varying widths and lengths to order. SELECTION CHART CATALOG NUMBER WATTS PER PANEL NOMINAL PANEL LENGTH 48”-59” 60”-71” 72”-83” PANEL WIDTH WATT DENSITY 24”-35” 36”-47” 10-13 High Med. Low 155 130 105 235 195 155 315 260 210 390^ 325^ 260^ N/A N/A N/A N/A N/A N/A N/A N/A N/A 14-17 High Med. Low 235 195 155 350 295 235 470 390 315 585^ 490^ 390^ N/A N/A N/A N/A N/A N/A N/A N/A. N/A 18-21 High Med. Low 315 260 210 470 390 315 625 520 415 780 650 520 940^ 780^ 625^ N/A N/A N/A N/A N/A N/A 22-28 High Med. Low 375 310 250 565 470 375 750 625 500 940 785 625 1125 940 750 1315 1095 875 1500 1250 1000 QT+**@@# LEGEND: + Watt Density: H = High, M = Medium, L = Low **Width of Panel @@Length of Panel 2. CUSTOM SIZE FRAMES ACCESSORIES CATALOG NO. DESCRIPTION QSF**@@ Surface Mounting Frame QRF**@@ Recess Mounting Frame ** Width of Heater (10” to 28”) @@Length of Heater (10” to 96”) 3. TEGULAR (revealed edge) Tegular systems may utilize a standard grid with a 15/16” cross-T or a "fine line" grid with a 9/16" cross-T. The acoustical tile is notched to hang below the grid creating the revealed edge. Tegular panels are built with a support angle on all four sides to allow the panel front to drop flush with the finished ceiling. REVEALED EDGE CEILING SYSTEM TEGULAR FINELINE TEGULAR FINELINE 9/16" GRID UNIVERSAL MOUNTING CLIPS RADIANT HEATING PANEL TEGULAR 15/16" GRID TEGULAR CEILING TILE Tegular and Fine line Tegular panels are supplied standard with universal mounting clips installed for support chain. 84”-95” 96” ^ Maximum Panel Length = 60 inches ^^ Maximum Panel Length = 72 Inches. # Voltage Designation: 1 = 120, 8 = 208, 2 = 240, 7 = 277, 3 = 347 To provide a continuous ceiling line around the perimeter of a building, the factory can provide panel fronts to be interspersed between the functioning heating panels. Field-trimmable filler panels also are available. 8.SEAL TIGHT FLEXIBLE CONDUIT AND CONNECTORS Radiant ceiling panels come with 1/2" Greenfield flexible conduit and straight connectors as standard equipment. Seal tight connectors and conduit can be substituted at the factory if panels are to be used in high moisture areas or if required by local electrical codes. 9. FACTORY SILICONE SEALED PANELS FOR USE IN HIGH MOISTURE AREAS - Exterior moisture and condensation do not affect heating panel 4. CONCEALED SPLINE SYSTEMS performance, but water inside the unit can These systems utilize ceiling tiles cause the panel to fail. Panels being used notched to hide the T-bar grid. heating in locker rooms and swimming pool areas panels will be treated in a manner should be totally sealed with silicone at the similar to the lights in such a system. We factory before shipment. If there is a will build a custom recessed frame and chance of moisture above the ceiling, then panel to fit inside the grid opening. The seal tight conduit and seal tight connectors also should be used. recessed frame will be suspended independently from the T-bar grid. The result is a flush-mounted panel with an exposed trim finishing off the adjacent tiles and supporting the panel. 10. LONGER FLEXIBLE CONDUIT Panels will replace the standard 48” Greenfield with up to 11’ of 1/2” flexible conduit. 5. SILKSCREEN Radiant heating panels can be silk screened to provide an architectural blend with leading acoustical tiles. For Tbar, concealed spline and tegular ceiling systems. 11. CONTROLS P/E Switches - factory prewired to heaters. 20 amps - 120V, 240V, 208V and 277V. Power Relay - factory prewired to heaters. 30 amps single pole, 120 volt holding coil. 6. CUSTOM COLORS 12. HEAVIER DUTY PANELS Radiant heating panels can be painted any color desired with high temperature acrylic paints without affecting panel performance. For special installations the factory can use heavier gauge steel in the construction of the panels. Radiant energy is emitted from heating panels in the 8-10 micron wavelength range. One of the principal characteristics of this wavelength is that it is not color selective as are shorter wavelengths. Consequently, the surface color of the panel is unimportant to heating efficiency and can be considered solely in the light of aesthetics. 13. STAINLESS STEEL CONSTRUCTION PANELS FOR CHLORINE STORAGE AREAS - Special stainless steel panels are available for chlorine storage areas. Panels will be equipped with seal tight connectors and silicone sealed. 14. MODULAR WIRING SYSTEMS For specific jobs, the factory can substitute modular connectors for the straight connectors and pig tails that are standard equipment. 3 CP SERIES ARCHITECT’S & ENGINEER’S SPECIFICATIONS * The electric ceiling heating panel shall be as manufactured by QMark, A Division of Marley Engineered Products, Bennettsville, SC. The construction and design shall permit it to be: recessed ceiling mounted with the use of Recessed Mounting Kit, fit into standard or custom designed modules of a T-bar suspended ceiling, or surface mounted with the use of a Surface Mounting Kit. Panels shall include the custom features listed below. HEATING ASSEMBLY: The heating assembly shall be UL Listed and CSA Certified and shall consist of powdered graphite encapsulated in a plastic laminate with heavy duty copper buss bars running the entire length, backed by 1 inch, 1 pound density high temperature fiberglass insulation to insulate against heat loss to the ceiling and separated from the inside of the panel by a dielectric insulation to assure uniform heat transfer throughout the entire radiating surface of the heater. The rated input shall be: (62.5 watts/sq. ft. with an average temperature of not more than 165 degree F.) or (95 watts/sq. ft. with an average surface temperature of 200 degree F.), to assure long trouble free life. The panel voltage shall be __________, (120, 208, 240, 277) WIRING: For connection to the main power supply, the heater shall be completely prewired, with the lead wires housed in a 48 inch length of flexible metal conduit and connector for J-Box mounting. Appropriate wiring diagrams shall appear on the back of the panel. Total length ___ in. by 1/2” (Max Length 132”) ____HEAVY DUTY CONSTRUCTION ___Gauge front ___Gauge back PANEL ASSEMBLY: The metal heating panel, containing the completely prewired heating assembly, shall be of 22 gauge formed galvanized steel front and 24 gauge formed galvanized steel back. Sides are overlapping front and back panels riveted together. ___STAINLESS STEEL CONSTRUCTION ___Panel ___Frame ____EARTHQUAKE CLIPS Surface Mounting Kit shall come in a separate carton which contains: two side frames, two end frames and eight assembly screws. Frame shall be field assembled before installing on ceiling. FINISH: The front of the heating panel shall be QMark’s unique multi-faceted crystalline type surface finished with high temperature silicone paint. CUSTOM FEATURES: Radiant heating panels shall be provided with the following custom features: ____CUSTOM SIZE _____in. Length, _____ in Width. ____SILK SCREENING to blend with acoustical tile. ____TEGULAR (Revealed edge) ____CUSTOM COLOR to match architectural samples. ____PAINTED FRAME to match heater (Surface or Recess only) ____FACTORY SILICONE SEALED ____SEAL TIGHT FLEXIBLE CONDUIT and CONNECTORS ____LONGER FLEXIBLE CONDUIT SURFACE MOUNTING Surface Mounting Kit shall come in a separate carton which contains: two side frames, two end frames and eight assembly screws. Frame shall be field assembled before installing on ceiling. END FRAME SURFACE MOUNTING RECESS MOUNTING Recess Mounting Kit shall come in a separate carton which contains: four frame sections and four corner pieces. Recess mounting shall require a: (Panel Length + 3/8”) X (Panel Width + 3/8”) cutout in the ceiling and a secure method of support. *QMark reserves the right to change specifications without prior notice. RECESS MOUNTING Recess Mounting Kit shall come in a separate carton which contains: four frame sections and four corner pieces. Recess mounting shall requires a: (Panel Length + 3/8”) X (Panel Width + 3/8”) cutout in the ceiling and a secure method of support. SCREWS SIDE FRAME END FRAME SIDE FRAME MOUNTING HOLES 4 CORNER
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Signing Date : 2010:03:16 09:51:32-04:00 Signing Authority : ARE Acrobat Product v8.0 P23 0002337 Document Usage Rights : FullSave Annotation Usage Rights : Create, Delete, Modify, Copy, Import, Export Form Usage Rights : Add, FillIn, Delete, SubmitStandalone Signature Usage Rights : Modify XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:30 Producer : Acrobat Distiller 4.0 for Macintosh Create Date : 2002:08:06 13:38:34Z Modify Date : 2010:03:16 09:51:32-04:00 Metadata Date : 2010:03:16 09:51:32-04:00 Creator Tool : QuarkXPress(tm) 4.11 Document ID : uuid:7e128033-e646-11d8-a281-000a95ba851c Instance ID : uuid:7b2246e5-5cf9-9247-93aa-f7cdbd3a9047 Format : application/pdf Creator : Marley Engineered Products Title : ZSS-QCPOO Has XFA : No Page Count : 4 Author : Marley Engineered ProductsEXIF Metadata provided by EXIF.tools